SPIROVENT MICROBUBBLE DEAERATORS AND DIRT SEPARATORS

Size: px

Start display at page:

Download "SPIROVENT MICROBUBBLE DEAERATORS AND DIRT SEPARATORS"

Corey Jackson
5 years ago
Views:

1 SPIROVENT MICROBUBBLE DEAERATORS AND DIRT SEPARATORS S P I R O V E N T A I R & D I R T

Air - and dirt - free system water through a single unit 1 100 mm N.B.

2 Air - and dirt - free system water through a single unit mm N.B. Weld end 100 mm N.B. Flanged 100 mm N.B. Demountable Weld end The life and the efficiency of a heating or cooling system is greatly dependant on the quality of the system water. Air and dirt problems cause frequent breakdowns and increased customer complaints. Corrosion, cavitation and wear amongst others are consequences of saturated air and dirty system water. Recuring problems and increased maintenance results in unnecessarily high costs and dissatisfied customers. There is a solution... A system totally without air and dirt is possible. There is a unique device whose combined action will remove all gases including dissolved air and dirt down to the smallest particle keeping the system free from air and dirt, permanently. It is maintenance free as it works without strainers or filters. Less maintenance fewer costs. The name: SPIROVENT AIR & DIRT 100 mm N.B. Hi-flow Weld end

THE CORE EXPOSES THE DIFFERENCES The crucial difference SPIROVENT AIR & DIRT 1.The automatic air vent is guaranteed not to leak and cannot be closed. Standard thread for connecting a vent pipe.

3 THE CORE EXPOSES THE DIFFERENCES The crucial difference SPIROVENT AIR & DIRT 1.The automatic air vent is guaranteed not to leak and cannot be closed. Standard thread for connecting a vent pipe. The unique construction of this combined unit allows it not just to remove free and dissolved air but also dirt particles. The special design of the Spirotube is at the heart of the unique combined action of the Spirovent. Dirt particles of al sizes sink to the bottom of the unit and collect in the dirt chamber, whilst the air bubbles rise and collect in the air chamber. The dirt can be flushed out while the system is in full operation through the drain valve. The air is released via the automatic air vent. 2.Lifting eyes make installation easy. 3. Special constructed air chamber to protect the valve mechanism from dirt. Sufficient volume to take care of pressure fluctuations. 4.Valve for releasing large amounts of air during filling and for skimming off floating scum. 5.Many different connections up to 300 mm are available from stock: weld end and flanged. 6.Dirt collected does not restrict flow. The large collector ensures that flushing is only required now and then. 7. The solid construction guarantees a long life. 8.The unique Spirotube is at the heart of the Spirovent. Designed to separate the smallest microbubble and microscopic dirt particle, yet it offers little resistance to flow. 9.Large capacity collection chamber reduces the need for frequent draining. 10.Drain valve for flushing out the dirt.

Heating System ADVANTAGES FOR THE SPECIFIER, INSTALLER AND END-USER Maximum protection of the installation by conditioning the system water. Increased system efficiency. Reduced risk of breakdown.

No by-pass, isolating valves or replacement filters minimum pressure drop, always constant can be flushed while fully operational. Three year guarantee.

4 Heating System ADVANTAGES FOR THE SPECIFIER, INSTALLER AND END-USER Maximum protection of the installation by conditioning the system water. Increased system efficiency. Reduced risk of breakdown. Greatly reduced commissioning time. Optimum heat transfer. Increased component life. No oxygen based corrosion or pump cavitation. Quiet operation. No by-pass, isolating valves or replacement filters minimum pressure drop, always constant can be flushed while fully operational. Three year guarantee. The Spirotube makes the difference The Spirotube is at the heart of the unit and determines its amazing performance. It s unique construction creates a still area of water inside the Spirovent which allows air bubbles to rise and dirt particles with a higher specific weight than water to sink. Microbubbles are formed Boiler Microbubble Deaerator & Dirt Separator Positioning in the system is important for optimum performance Microbubbles are released at the hottest spot in an installation. This release of gas is based on Henry s Law. This physical law states that the solubility of gases in water reduces with an increase in temperature and/or a decrease in pressure. In simple terms air is released from the water as the temperature increases or the pressure decreases. When determining the best location for installation the microbubble separation is the determining factor. Therefore the Spirovent must be installed at the hottest point in the system. For a heating installation this is in the flow from the boiler. The static head above the point of installation must not exceed 15 metre. In a chilled water circuit the warmest point is usually in the return to the Chilled Water System Microbubble Deaerator & Dirt Separator Maximum 5 metre Maximum 15 metre Absorption of trapped air chiller. The maximum static head above the Spirovent must not exceed 5 metre. For dirt separation the location in the system is not of importance and is always secondary to the deaeration.* *For more detailed technical information about Henry s Law and the deaeration cycle a booklet called Spirotism is available. HOW SMALL ARE DIRT PARTICLES? 0,001 1 um Range Spirovent Dirt Visible to the naked eye Range standard filter Hair Hematite Sand Magnetite Welding grain 0,01 0, mm um Microbubbles are formed Chiller When the drain valve is opened the system pressure flushes out the collected dirt. This only takes a few seconds. The Hi-flow has been specially designed for water circuits with flow rates between 1 and 3 m/s.

Flow Resistance Spirovent Air & Dirt Pressure drop [kpa] 100 10 1 22 mm 1" DN50 DN65 DN80 DN100 DN125 DN150 DN200 DN250 DN300 Measured values according to Spirotech standard.

5 Flow Resistance Spirovent Air & Dirt Pressure drop [kpa] mm 1" DN50 DN65 DN80 DN100 DN125 DN150 DN200 DN250 DN300 Measured values according to Spirotech standard. Shown values are maximum values. For further information please contact us. 0,1 0, Water flow rate in [m 3 /h] Technical Specification Bore Size NB (DN) mm Weld End OD mm H2 mm H2 Hi-flow mm OD R1/2 h2 mm DN H2 h2 Hi-flow mm D mm h2 DF mm e/female G L mm LF mm e D L LF Flow Rate 1 m/s m 3 /h Flow Rate Hi-flow 3 m/s m 3 /h Volume l Volume Hi-flow l Weight kg 12 / / / / / / / / / 544 Weld / Flanged DN OD h2 R1/2 H2 Weight Demountable kg 30 / / / / / / / / / 609 Weld / Flanged Weight kg 20 / / / / / / / / / 854 Hi-flow Weld / Flanged Weight Demountable kg 38 / / / / / / / / / 919 Hi-flow Weld / Flanged e D DF L LF The Spirovent is designed for a maximum working temperature of 110 C and a max. operating pressure of 10 bar g. The system pressure must always be positive. From 50 mm NB the Spirovent is made from carbon steel. Flanges are drilled to DIN PN16. The body of the Spirovent 22mm and 1 are made from brass. d/female G 22 mm comp. 1 H2 mm h2 mm L mm Flow Rate m 3 /h 1,25 2 Volume l Weight kg Ø65 d L 52 h2 R1/2 H2 Other materials, pressures and temperatures are available on request.

Spirovent Deaerators and Dirt Separators are manufactured by Spirotech bv Helmond The Netherlands A Spiro Research Company SPIROVENT The application of our products and the positioning of them in

6 Spirotech is the world leader in deaeration and dirt separation technology for heating and cooling systems. Spirovent also finds many applications in the chemical and process industry, solar energy systems and of course in district heating installations. Spirovent Deaerators and Dirt Separators are manufactured by Spirotech bv Helmond The Netherlands A Spiro Research Company SPIROVENT The application of our products and the positioning of them in your system often require special consideration. The diagrams shown in this brochure are only indicative of a general installation. We will be pleased to advise you on any specific application. The manufacturer reserves the right to make changes without prior notification. Copyright Spirotech bv Information given in this brochure may not be reproduced complete or in part without the prior written consent of Spirotech bv /07-04 Spirotech bv, Churchilllaan 52, P.O. Box 207, 5700 AE Helmond, The Netherlands, Phone: +31 (0) , Fax: +31 (0) , info@spirotech.nl,

DIRT SEPARATORS FOR HEATING, COOLING AND PROCESS SYSTEMS

spirotrap DIRT SEPARATORS FOR HEATING, COOLING AND PROCESS SYSTEMS SPIRO EXCEPTIONAL GUARANTEE DOMESTIC COMMERCIAL INDUSTRY The smallest particle of dirt can cause the biggest problems Dirt in system water