S380 Barbecue Assembly Manual

Transcription

1 S380 arbecue ssembly Manual (G31216) Propane 1 YER LIMITED WRRNTY RED ND SVE MNUL FOR FUTURE REFERENCE. If pre-assembled, leave this manual with unit for consumer s future reference. For product inquiries, parts, warranty and troubleshooting support, please call Manual Revision #: PD NS Z21.58b-2012-CS 1.6b-2012 NS Z21.58b-2012-CS 1.6b-2012

2 HEVY RTICLE NEEDS 2 TO LIFT THIS MNUL MUST REMIN WITH THE PRODUCT T LL TIMES To ORDER non-warranty replacement parts or accessories, or to register your warranty, please visit us on the web at CUTION Sharp edges. Wear gloves when assembling your grill. CUTION Read and follow all safety statements, assembly instructions, use and care directions before attempting to assemble and cook. INSTLLER OR SSEMLER/CONSUMER This manual should be kept with the Q at all times. WRNING Failure to follow all of the Manufacturer s instructions could result in hazardous fires, explosions, property damage, or serious personal injury or even death. Follow all leak check procedures carefully prior to operation of barbecue, even if grill was dealer assembled. Do not try to light this barbecue without reading the Lighting Instructions section of this manual. DNGER 1. If you smell Gas: a. Shut off gas to the appliance b. Extinguish any open flame c. Open lid d. If odor continues, keep away from the appliance and immediately call your gas supplier or your fire department 2. Requires two people to complete the assembly process. 3. eware of sharp edges. WRNING 1. Do not store or use gasoline or other flammable liquids or vapours in the vicinity of this or any other appliance. 2. n LP cylinder not connected for use shall not be stored in the vicinity of this or any other appliance. WRNING IN DIRECT SUN, ND IN OPERTION, YOUR Q S STINLESS STEEL ND PINTED STEEL PRTS CN ECOME VERY HOT. THIS RECUE IS FOR OUTDOOR USE ONLY CONTCT CLL CENTRE IF NY PRTS RE MISSING

3 HRDWRE PCK TOOLS NEEDED FOR SSEMLY #2 Phillips screwdriver (long and short) ¼ Slotted screwdriver (long and short) djustable wrench Pliers For correct hardware assembly, always position the lock washer between the screw and the flat washer. KEY # DESCRIPTION PRT NUMER QUNTITY 1 NO.10-24UNCx13 Screw G /4-20UNCx13 Screw #8x3/8 Self Tapping Screw Washer (Wheel) G Hitch Pin G Screw Lock Washer Flat Washer Caution: Sheet metal can cause injury. Wear gloves when installing the grill NO.10-24UNCx13 Screw X 12 ¼ -20UNCx13 Screw X 4 #8x3/8 Self Tapping Screw X Washer (Wheel) X 3 Hitch Pin X 1 EFORE SSEMLING THIS RECUE, RED THE INSTRUCTIONS CREFULLY. ssemble the barbecue on a flat, clean surface. Grill is heavy. Two people are recommended to complete assembly. 1

4 PRTS LIST (PROPNE) FOR (G31216) KEY # QUNTITY DESCRIPTION PRT NO. 1 Top lid assembly G Lid handle brackets G C 1 Top lid handle G D 2 Lid bumpers-back G E 2 Lid bumpers-front G F 2 Screws for lid G urner box assembly G Side Heat shield G C 3 urner G312-0D00-01 D 1 Electrode G E 2 Carryover assembly G F 3 Flame tamer G G 2 Cooking grate G H 1 Warming rack G C 1 Control panel G C 1 Manifold assembly G CC 1 Regulator G CD 3 Control knob G CE 1 Ignitor G CF 1 Grease cup hook G CG 1 Grease cup G CH 1 Heat shield (tank) G D 1 Lower cart frame, right G312-0F00-01 D 1 Upper cart frame, right G312-0H00-01 DC 1 Lower cart frame, left G312-0E00-01 DD 1 Upper cart frame, left G312-0G00-01 DE 2 Upper cart brace G312-F00-01 DF 1 Upper back brace G DG 1 Lower back brace G DH 1 Upper front panel G DI 1 Lower front panel G DJ 2 End caps G DK 2 Wheel G DL 1 Wheel axle G DM 1 Match holder G DN 3 Tank exclusion G E 2 Side shelf table G F1 1 Hardware pack G F2 1 ssembly instructions G312-M F3 1 Safe use and care manual G451-M

5 EXPLODED DIGRM (PROPNE) FOR (G31216) G D E H F F C CC C D E DD E CH C CE CD E DE DN DF C DG D DM DH D CF CG DC DL DK DI DJ F1 HRDWRE PCK F2 SSEMLY MNUL F3 SFETY ND CRE MNUL 3

6 1 D a. ssemble hardware half way into the lower left and right cart frames (DC and D). Do not tighten. YOU WILL NEED: 1 X 8 DC 4

7 1 D b. Position the upper front panel (DH) and lower front panel (DI) onto the screws attached to the left and right lower cart frames (DC and D) as shown in figure & C. DH DI D DH D DH DI C c. Tighten screws. D DH 5

8 2 DC a. To assemble the upper and lower back brace (DF and DG) to the left and right cart frames (D and DC) first partially assemble screws half way into the back of the parts (D & DC) as shown in figure. Do not tighten. D YOU WILL NEED: 1 X 4 b. Position the upper back brace (DF) and lower back brace (DG) onto the screws you assembled in 2. DF DG c. Tighten screws. 6

9 3 DJ Insert end caps (DJ) into the lower cart frame, right (D). DJ D ack view DJ D DJ DJ D ack view 7

10 4 DL DK DK a. Place one wheel (DK) on the wheel axel (DL) followed by 2 wheel washers (#4). Complete assembly by adding the second wheel (DK), a third wheel washer (#4), and secure with the hitch pin (#5). YOU WILL NEED: X 3 X 1 DK DL 4 DK b. With the cart assembly in the upside down position, firmly push the wheel assembly (DL and DK) into the opening at the bottom of the left lower cart frame (DC). Make sure that the inside wheel spacers are positioned on the outside of the left cart legs. DC 4 5 C, correct assembly D, correct assembly, back view 8

11 5 DN DH DI ssemble the three tank exclusion wires (DN) to the lower back brace (DG) and the front panel (DI and DH) as shown. YOU WILL NEED: 3 DG X 3 ack view DH DN DI DN, front view DG DN, back view 9

12 6 + Note: TWO PEOPLE required for this step. Ensure that the regulator hose (CC) is hanging outside of cart. CC a. Position the top lid and burner box assembly (&) onto the cart assembly (C). C Front View b. ssemble hardware as shown. DF DD YOU WILL NEED: 2 X 4 ack View 10

13 7 C a. ssemble the control knobs (CD) onto the valve stems of the manifold assembly (C) located on the control panel (C). CD C CE C b. Verify the urner Electrode Wire is connected to the Igniter (CE), as shown. View from underneath control panel CE 11

14 8 SIDE SHELF SSEMLY a. Loosen the hardware pre-assembled to the right upper cart frame (D) as shown in figure. Right side view D b. Position the right side shelf (E) onto the hardware loosened in Step 9. Tighten the hardware. E Right side view 12

15 9 a. Loosen the hardware pre-assembled to the left upper cart frame (DD) as shown in figure. Left side view DD b. Position the left side shelf (E) onto the hardware loosened in Step 10. Tighten the hardware. E Left side view 13

16 10 F Place the flame tamers (F) into the burner box assembly (). 11 Place the cooking grates (G) into the burner box assembly (). G 14

17 12 H Stationary wire To assemble the warming rack (H), insert the stationary wire into the holes on the sides of the lid. Insert warming rack pivot legs into the holes on the inside of the burner box assembly, as shown. Pivot legs H 13 Hang the grease cup hook (CF) from the bottom of the burner box (), and place grease cup (CG) into position. CF CG CF CG 15

18 14 DC Position the gas tank onto the top and bottom tank supports, attached to the lower cart frame, left (DC) as shown. DC 15 ttach the regulator coupling nut (CC) to the propane tank valve. CC TTENTION FOR YOUR SFETY, DO NOT TTEMPT TO LIGHT THIS Q UNTIL YOU HVE REVIEWED PGES 4-8 OF THE MSTER CHEF SFETY & CRE MNUL. LL SFETY ND LEK TESTS MUST E PERFORMED Y THE END USER, PRIOR TO LIGHTING THIS Q. 16

19 17

20 Visit to complete product registration Master Chef Customer Service Trileaf Distributions Trifeuil Toronto, Ontario M4S 28