SBRL-SERIES SPREADER BEAMS INSTRUCTION MANUAL
|
|
- Brandon Miller
- 5 years ago
- Views:
Transcription
1 VESTIL MANUFACTURING CORP North Wayne Street, P.O. Box 507, Angola, IN Telephone: (260) or- Toll Free (800) Fax: (260) SBRL-SERIES SPREADER BEAMS INSTRUCTION MANUAL Receiving instructions: After delivery, remove the packaging from the product. Inspect the product closely to determine whether it sustained damage during transport. If damage is discovered during the inspection, immediately record a complete description of the damage on the bill of lading. If the product is undamaged, discard the packaging. NOTE: The end-user is solely responsible for confirming that product design, installation, use, and maintenance comply with laws, regulations, codes, and mandatory standards applied where the product is used. Table of Contents Signal Words Safety Guidelines SBRL-25 Exploded parts diagram, bill of materials, & specifications. 4 SBRL-40 Exploded parts diagram, bill of materials, & specifications 5 SBRL-80 Exploded parts diagram, bill of materials, & specifications 6 Using the roll lifter Inspections. 9 Labeling diagram Limited warranty. 10 Copyright 2017 Vestil Manufacturing Co. Page 1 of 10
2 Signal Words: This manual uses SIGNAL WORDS to identify situations likely to result in personal injury or property damage. These words also indicate the seriousness of those injuries. Signal words used in this manual appear below along with their definitions. Identifies a hazardous situation which, if not avoided, WILL result in DEATH or SERIOUS INJURY. Use of this signal word is limited to the most extreme situations. Identifies a hazardous situation which, if not avoided, COULD result in DEATH or SERIOUS INJURY. Indicates a hazardous situation which, if not avoided, COULD result in MINOR or MODERATE injury. Identifies practices likely to result in product/property damage, such as operation that might damage the product. Safety Guidelines VESTIL strives to identify foreseeable hazards associated with the use of its products. However, material handling is inherently dangerous and no manual can address every conceivable risk. The end-user ultimately is responsible for exercising sound judgment at all times. If this product is used improperly or carelessly, the user and/or bystanders might sustain serious personal injuries or even be killed. Therefore, each person who assembles, uses or maintains this lifting device should read and understand the entire manual before installing, using or servicing the product for the first time. Failure to do so is a misuse of the product. If you do not understand an instruction, ask your supervisor for clarification. Read the manual to refresh your understanding of proper use and maintenance procedures when necessary. To reduce the likelihood of injury: ALWAYS inspect the spreader beam before each use according to the inspection procedures described in the most recent revision of ASME B Consult the safety messages included in the manuals for your crane, trolley, hoist, and any other device used in conjunction with this spreader beam. Always make sure that the shackle pin (see Item 4, Shackle, in Exploded Parts Diagrams on p. 3-5) is secure before applying a load to the load hook. Tighten the pin before each use. BEFORE releasing the roll material, be certain that it is fully supported by the ground or other surface, and is fully immobilized (can t fall over, roll, slide, or move in an uncontrolled manner). If a second person is needed to immobilize the material, find someone to help you. ALWAYS attach the spreader beam to a safety hook (e.g. a hoist that has a safety hook attached to the end of the chain or cable), or to a connection that includes safety mechanisms to prevent accidental/unintended detachment from the hoist. DO NOT use the device on a hoist hook that might accidentally/unintentionally release the clamp. DO NOT connect the beam to a safety hook that does not function properly or that is damaged. Clear all debris, including fluids, from the path of travel if the job requires moving the material to a new location BEFORE picking up the load. If moisture is present in the path of travel, absorb it before using the clamp. DO NOT remove or obscure any label. Verify the placement and legibility of all labels as shown in the label placement diagram on p. 9. If a label is damaged or unreadable, immediately contact Vestil for a replacement. DO NOT use the beam UNLESS all labels are securely attached and readable. DO NOT attempt an unbalanced lift. Before lifting a roll, confirm that it is properly balanced. (See Using the Lifter, on p. 9. DO NOT lift more than 1 roll at a time. Only lift rolls from the horizontal position. DO NOT sit on or apply any weight/pressure to the material held by the clamp. DO NOT attempt to lift material that weighs more than the rated load of the clamp. ALWAYS make sure that the material weighs no more than the rated load of the clamp. DO NOT lift a load higher than necessary. DO NOT walk beneath a raised load or allow other persons to do so. Copyright 2017 Vestil Manufacturing Co. Page 2 of 10
3 (continued from p. 2) DO NOT use the spreader beam to lift material over people or to lift any apparatus that supports people, such as a work platform. The beam is designed ONLY to lift material on rolls. DO NOT get in front of or behind a suspended load while moving it. Always orient yourself so that the load is visible to you. You are less likely to be injured if the load remains within your sight at all times. DO NOT leave suspended material unattended. An unattended, suspended load creates a risk of injury to yourself and others. Always move the load to its desired location, set it down and properly immobilize it; then disengage the load. DO NOT attempt to resolve any problem with the product unless you are both authorized to do so and certain that it will be safe to use afterwards. Inspect the product before each use, as described in Inspections & Maintenance Recommendations on p. 9, to confirm normal condition. DO NOT use the product if any unusual noise or movement is observed. If a malfunction occurs, remove the unit from service and notify your supervisor & maintenance personnel about the issue. DO NOT exceed the capacity of this product (see Product specifications table below and Label placement diagram on p. 9). DO NOT modify the spreader beam or any component in any way UNLESS you first obtain written approval from Vestil. Unauthorized modifications automatically void the Limited Warranty (p. 10) and might make the beam unsafe to use. DO NOT use the lifting device UNLESS all product labels (see Label placement diagram on p. 9) are readable and undamaged. Proper use, maintenance, and storage are essential for this product to function properly. o Always use this product in accordance with the instructions in this manual and consistent with any training relevant to hoists and rigging used in conjunction with this product. o Keep the product clean & dry. Periodically lubricate moving parts. Copyright 2017 Vestil Manufacturing Co. Page 3 of 10
4 SBRL-25: Exploded Parts Diagram, & Bill of Materials Item Part no. Description Qty SBRL-25 spreader frame weldment SBRL-25 roll lifting shaft Roll retainer with detent pins Shackle with screw pin ton hook 2 **Includes sling SL-2-F-4 Specifications: Model Maximum roll length Capacity Net weight SBRL-25 6 feet 1.8m 2,500lb. 1,136.4kg 88 lb. 40 kg Copyright 2017 Vestil Manufacturing Co. Page 4 of 10
5 SBRL-40: Specifications, Exploded Parts Diagram, & Bill of Materials Item Part no. Description Qty SBRL-40 spreader frame weldment SBRL-40 roll lifting shaft Roll retainer with detent pins Shackle with screw pin, 1 / 2, 2 ton ton hook 2 **Includes sling SL-2-F-4 Specifications: Model Maximum roll length Capacity Net weight SBRL-40 6 feet 1.8m 4,000 lb kg 200 lb. 91 kg Copyright 2017 Vestil Manufacturing Co. Page 5 of 10
6 SBRL-80: Specifications, Exploded Parts Diagram, & Bill of Materials Item Part no. Description Qty SBRL-80 spreader frame weldment SBRL-40 roll lifting shaft Roll retainer with detent pins Shackle with screw pin ton swivel hook 2 **Includes sling SL-4-F-4 Specifications: Model Maximum roll length Capacity Net weight SBRL-80 8 feet 2.4 m 8,000 lb kg 489 lb kg Copyright 2017 Vestil Manufacturing Co. Page 6 of 10
7 Using the roll lifter: The capacity of the hoist should equal or exceed the capacity of the roll lifter. DO NOT exceed the capacity of the lifter or the hoist, whichever is smaller. The capacity of each roll lifter model is listed in the table on p. 3 and is displayed on label 287 (see Label placement diagram on p. 10). 1. Pull up/down on the detent pins (of the roll retainers); then slide the tubes off of the roll lifting shaft. Pull out detent pins Roll lifting shaft Roll retainer 2. Insert the roll lifting tube through the roll. Adjust the position of the lifting shaft so that it is centered lengthwise inside the roll. Roll material Detent pin holes 3. Install the retainers. Pull out the detent pins and slide a retainer onto each end of the roll lifting shaft. Press the retainers against the ends of the roll; then release the detent pins. Adjust the position of each retainer until the detent pins seat inside pin holes. Retainers should seat into place as close to the ends of the roll as possible. Detent pin Retainer should contact or be as close as possible to roll material Roll retainer Detent pins seat in pin holes Copyright 2017 Vestil Manufacturing Co. Page 7 of 10
8 4. Adjust the location of the hooks. Each hook should hang above the center of the sling channel of a retainer. Sling channel To change the position of a hook, remove the threaded pin from a shackle; then reattach the shackle to the spreader frame via the appropriate pin hole. Pin holes are 4 inches apart. 4in. Unscrew threaded pin 5. Attach one end of a sling to one of the hooks, wrap the sling around the sling channel of a retainer, and then attach the other end of the sling to the hook. Attach a second sling to the other hook in the same fashion. Copyright 2017 Vestil Manufacturing Co. Page 8 of 10
9 6. Raise the load a few inches above the ground and verify that it is properly balanced. If one end of the load is considerably lower than the other, return the load to the ground and reposition the retainers, hooks, and shackles. When properly balanced, the spreader beam and roll will be horizontal. Inspections NOTE: Perform the recommended inspections in ASME B Inspect the spreader beam as frequently as indicated in this section to confirm that it is in normal operating condition. A designated person should verify that the spreader beam complies with all regulations, codes, and standards that apply to Below-the-Hook Lifting Devices in the location where the beam is used. Before each use, inspect all of the components listed below. Do not use this lifting device unless ALL components are in normal condition: 1. Spreader frame assembly: Examine each pin hole for elongations and the surrounding metal for cracks, and severe rusting and corrosion. Pin holes should be smooth and circular; the frame should be square and rigid and should lack cracks, warps, regions weakened by severe rusting or corrosion, etc. 2. Roll lifting shaft: confirm that the shaft is straight and rigid. Also examine the pin holes through the shaft for flared areas, elongations, cracks, bends, and warps. 3. Pins: inspect all of the detent pins (of the roll retaining tubes) and all threaded pins (part of the shackles). Confirm that pins are straight and without cracks or warps. 4. Hooks and shackles (hardware): examine each hook and shackle for damage including excessive wear, warping, cracks, or deformation. Remove and replace a hook or shackle that is damaged; 5. Roll retainers: confirm that both retaining tubes are free of warps and cracks. Confirm that the detent pins are firmly connected to the retaining tubes. 6. Product labels: all labels should be readable and located as shown in the label placement diagram below. If a label(s) is unreadable or missing, contact Vestil to order a replacement. 7. Welds: confirm that all welds are intact. Labeling diagram Each spreader beam should be labeled as shown below. Replace any label that is missing, damaged, or unreadable. DO NOT use this product unless all labels are in place. Label 287 Label 675 Copyright 2017 Vestil Manufacturing Co. Page 9 of 10
10 LIMITED WARRANTY Vestil Manufacturing Corporation ( Vestil ) warrants this product to be free of defects in material and workmanship during the warranty period. Our warranty obligation is to provide a replacement for a defective original part if the part is covered by the warranty, after we receive a proper request from the warrantee (you) for warranty service. Who may request service? Only a warrantee may request service. You are a warrantee if you purchased the product from Vestil or from an authorized distributor AND Vestil has been fully paid. What is an original part? An original part is a part used to make the product as shipped to the warrantee. What is a proper request? A request for warranty service is proper if Vestil receives: 1) a photocopy of the Customer Invoice that displays the shipping date; AND 2) a written request for warranty service including your name and phone number. Send requests by any of the following methods: Mail Fax Vestil Manufacturing Corporation (260) sales@vestil.com 2999 North Wayne Street, PO Box 507 Phone Angola, IN (260) In the written request, list the parts believed to be defective and include the address where replacements should be delivered. What is covered under the warranty? After Vestil receives your request for warranty service, an authorized representative will contact you to determine whether your claim is covered by the warranty. Before providing warranty service, Vestil may require you to send the entire product, or just the defective part or parts, to its facility in Angola, IN. The warranty covers defects in the following original dynamic components: motors, hydraulic pumps, electronic controllers, switches and cylinders. It also covers defects in original parts that wear under normal usage conditions ( wearing parts ), such as bearings, hoses, wheels, seals, brushes, and batteries. How long is the warranty period? The warranty period for original dynamic components is 90 days. For wearing parts, the warranty period is 90 days. The warranty periods begin on the date when Vestil ships the product to the warrantee. If the product was purchased from an authorized distributor, the periods begin when the distributor ships the product. Vestil may, at its sole discretion, extend the warranty periods for products shipped from authorized distributors by up to 30 days to account for shipping time. If a defective part is covered by the warranty, what will Vestil do to correct the problem? Vestil will provide an appropriate replacement for any covered part. An authorized representative of Vestil will contact you to discuss your claim. What is not covered by the warranty? 1. Labor; 2. Freight; 3. Occurrence of any of the following, which automatically voids the warranty: Product misuse; Negligent operation or repair; Corrosion or use in corrosive conditions; Inadequate or improper maintenance; Damage sustained during shipping; Accidents involving the product; Unauthorized modifications: DO NOT modify the product IN ANY WAY without first receiving written authorization from Vestil. Modification(s) might make the product unsafe to use or might cause excessive and/or abnormal wear. Do any other warranties apply to the product? Vestil Manufacturing Corp. makes no other express warranties. All implied warranties are disclaimed to the extent allowed by law. Any implied warranty not disclaimed is limited in scope to the terms of this Copyright 2017 Vestil Manufacturing Co. Page 10 of 10
MCHT-350 MAGNETIC CYLINDER HAND TRUCK INSTRUCTION MANUAL
VESTIL MANUFACTURING CORP. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868 Fax: (260) 665-1339 www.vestilmfg.com e-mail: sales@vestil.com
Rev. 10/27/2015 CDL-2000, MANUAL
VESTIL MANUFACTURING CORP. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 Toll Free (800) 348-0868 Fax: (260) 665-1339 www.vestilmfg.com e-mail: sales@vestil.com CDL-2000
HOOK-BASE INSTRUCTION MANUAL
VESTIL MANUFACTURING CORP. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868 Fax: (260) 665-339 www.vestilmfg.com e-mail: sales@vestil.com
CART-800-D-TS INSTRUCTION MANUAL
VESTIL MANUFACTURING CORP. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868 Fax: (260) 665-1339 www.vestilmfg.com e-mail: sales@vestil.com
rev. 2/24/2017 ALUMINUM SHEET DECK PLATFORM TRUCK ASD
VESTIL MANUFACTURING CORP. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868 Fax: (260) 665-1339 www.vestilmfg.com e-mail: sales@vestil.com
CYL-EH, CYL-EH-FF, CYL-EH-FP, & CYL-EH-FP-FF Cylinder Dollies Instruction Manual
Vestil Manufacturing Co. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868 Fax: (260) 665-1339 www.vestilmfg.com e-mail: sales@vestil.com CYL-EH,
COLV-6 SERIES VERTICAL CROSSOVER LADDERS INSTRUCTION MANUAL
VESTIL MANUFACTURING CORP. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868 Fax: (260) 665-1339 www.vestilmfg.com e-mail: sales@vestil.com
CANT-Series Cantilever Carts Instruction Manual
Vestil Manufacturing Corp. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 Toll Free (800) 348-0868 Fax: (260) 665-1339 www.vestilmfg.com e-mail: HUinfo@vestil.comU CANT-Series
RLAD-series Portable 2-Step Ladders Instruction Manual
VESTIL MANUFACTURING CORP. 999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (60) 665-7586 -or- Toll Free (800) 348-0868 Fax: (60) 665-1339 www.vestilmfg.com e-mail: HUsales@vestil.comU
RDC 100 & RDC DRUM ROTATING CARTS ASSEMBLY INSTRUCTIONS
Vestil Manufacturing Corp. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665 7586 or Toll Free (800) 348 0868 Fax: (260) 665 1339 www.vestilmfg.com e mail: info@vestil.com RDC
LAD-MM Series Mobile Ladder Stands Instruction Manual
Rev..8.07 LAD-MM, MANUAL Vestil Manufacturing Corp. 999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (60) 665-7586 -or- Toll Free (800) 348-0868 Fax: (60) 665-339 Web: www.vestilmfg.com
CJ-BEAM Trailer Stabilizing Jacks Instruction Manual
Vestil Manufacturing Corp. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868 Fax: (260) 665-1339 www.vestilmfg.com e-mail: sales@vestil.com
CRP-series Carpet Rams Instruction Manual
Vestil Manufacturing Corp. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868 Fax: (260) 665-1339 Web: www.vestilmfg.com e-mail: info@vestil.com
CRF-SERIES CARPET POLES INSTRUCTION MANUAL
VESTIL MANUFACTURING CORP. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868 Fax: (260) 665-1339 www.vestilmfg.com e-mail: sales@vestil.com
LPC-SERIES POSITIVE LOCKING PLATE CLAMPS USE AND MAINTENANCE MANUAL
VESTIL MANUFACTURING CORP. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868 Fax: (260) 665-1339 www.vestilmfg.com e-mail: sales@vestil.com
FE-Series Fork Extensions Instruction Manual
Vestil Manufacturing Corp. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868 Fax: (260) 665-1339 Web: www.vestilmfg.com e-mail: info@vestil.com
ABLT-H SERIES AIR BAG LIFT TABLES INSTRUCTION MANUAL
VESTIL MANUFACTURING CORP. 999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (60) 665-7586 -or- Toll Free (800) 348-0868 Fax: (60) 665-1339 www.vestilmfg.com e-mail: sales@vestil.com ABLT-H
LAD-EZ Series Portable Warehouse Ladders, 6-12 Steps Assembly Manual
Rev. 3/3/07 LAD-EZ (6- STEPS), MANUAL Vestil Manufacturing Corp. 999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (60) 665-7586 -or- Toll Free (800) 348-0868 Fax: (60) 665-339 www.vestilmfg.com
LAD-series Portable Warehouse Ladders, 6-12 Steps Instruction Manual
Rev. 3/3/07 LAD (6- STEPS), MANUAL VESTIL MANUFACTURING CORP. 999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (60) 665-7586 -or- Toll Free (800) 348-0868 Fax: (60) 665-339 www.vestilmfg.com
LSC SD LANDSCAPE CART ASSEMBLY I NSTRUCTIONS
VESTIL MANUFACTURING CORP. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665 7586 or Toll Free (800) 348 0868 Fax: (260) 665 1339 www.vestilmfg.com e mail: sales@vestil.com LSC
CYL-EX-12-S, CYL-EX-12-E, CYL-EX-18-S & CYL-EX-18-E Series Cylinder Storage Cabinets Assembly and Maintenance Manual
VESTIL MANUFACTURING CORP. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868 Fax: (260) 665-1339 www.vestilmfg.com e-mail: sales@vestil.com
08/2010 Rev. 2/7/2018 DGS-A, MANUAL. DGS-A, DGD-A, & DGS-AG Fork-Mounted Drum Lifters Use and Maintenance Manual DGS-AG
Vestil Manufacturing Corp. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868 Fax: (260) 665-1339 www.vestilmfg.com Email: info@vestil.com DGS-A,
LSC 3052 PCW LANDSCAPE CART ASSEMBLY INSTRUCTIONS
VESTIL MANUFACTURING CORP. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665 7586 or Toll Free (800) 348 0868 Fax: (260) 665 339 www.vestilmfg.com e mail: sales@vestil.com LSC
TT Series Benchtop Turntables Instruction Manual
Vestil Manufacturing Corp. 2999 North Wayne Street, P.O. Box 507, Angola, IN 6703 Telephone: (260) 665-7586 -or- Toll Free (800) 38-0868 Fax: (260) 665-1339 URL: www.vestilmfg.com Email: info@vestil.com
P-HOP-Series Portable Steel Hoppers Instruction Manual
VESTIL MANUFACTURING CORP. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868 Fax: (260) 665-1339 www.vestilmfg.com e-mail: sales@vestil.com
08/2010 Rev. 4/28/2017 FMDL, MANUAL. FMDL-Series Single & Double Eagle Beak Fork-Mounted Drum Lifters Use and Maintenance Manual
Vestil Manufacturing Corp. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868 Fax: (260) 665-1339 www.vestilmfg.com Email: info@vestil.com FMDL-Series
LAD-RF Series Collapsible Mobile Ladder Stands Instruction Manual
Rev..4.05 LAD-RF, MANUAL.doc Vestil Manufacturing Corp. 999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (60) 665-7586 -or- Toll Free (800) 348-0868 Fax: (60) 665-339 Url: www.vestilmfg.com
HOP-LP Portable Steel Dumping Hoppers Instruction Manual
VESTIL MANUFACTURING CORP. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868 Fax: (260) 665-1339 www.vestilmfg.com e-mail: sales@vestil.com
Rev. 12/16/2015 WTJ-HITCH, MANUAL. WTJ-HITCH Series Hitch-Mounted Jib Cranes Use and Maintenance Manual
VESTIL MANUFACTURING CORP. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868 Fax: (260) 665-1339 www.vestilmfg.com e-mail: sales@vestil.com
Instruction Manual DJG-100 and DJG
Vestil Manufacturing Corp. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868 Fax: (260) 665-1339 www.vestilmfg.com e-mail: info@vestil.com
OROAD-400 Traction Drive Electric Cart Use & Maintenance Manual
Rev. 8/8/2017 OROAD-400, MANUAL.doc VESTIL MANUFACTURING CORP. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868 Fax: (260) 665-1339 Web: www.vestilmfg.com
D-SERIES HOPPERS Instruction Manual
Vestil Manufacturing Corp. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868 Fax: (260) 665-339 Website: www.vestilmfg.com e-mail: info@vestil.com
WP-400 Series Electric Work Platforms Instruction Manual
VESTIL MANUFACTURING CORP. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868 Fax: (260) 665-1339 www.vestilmfg.com e-mail: sales@vestil.com
VAN-J Series Vehicle Mounted Jib Cranes Instruction Manual
Vestil Manufacturing Corp. 2999 North Wayne Street, P.O. Box 507, Angola, IN 4670 Telephone: (260) 665-7586 -or- Toll Free (800) 48-0868 Fax: (260) 665-19 Web: www.vestilmfg.com e-mail: HUinfo@vestil.comU
H-SERIES HOPPERS Instruction Manual
Rev. 7/20/208 H-hoppers MANUAL Vestil Manufacturing Corp. 2 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868 Fax: (260) 665-33 Web: www.vestilmfg.com
Table of Contents Rev. 10/31/2018 FHA MANUAL. FHA-series Fixed Height Aluminum Gantry Crane Instruction Manual
Vestil Manufacturing Corp. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868 Fax: (260) 665-339 Web: www.vestilmfg.com e-mail: info@vestil.com
H-SERIES HOPPERS Instruction Manual
Rev. /2/208 H, MANUAL.doc VESTIL MANUFACTURING CORP. 2 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868 Fax: (260) 665-33 www.vestilmfg.com e-mail:
INSTRUCTION MANUAL VERTICAL PLATE CLAMP MODEL EPC (10, 20, 40, & 80)
INSTRUCTION MANUAL VERTICAL PLATE CLAMP MODEL EPC (10, 20, 40, & 80) MODEL NO. SERIAL NO. VESTIL MANUFACTURING CORP. 2999 NORTH WAYNE STREET, P.O. BOX 507, ANGOLA, IN 46703 TELEPHONE: (260) 665-7586 -OR-
LP-6 LPG Cylinder Truck Use & Maintenance Manual
VESTIL MANUFACTURING CORP. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868 Fax: (260) 665-1339 www.vestilmfg.com LP-6 LPG Cylinder Truck
P-JIB Portable Jib Crane Instruction Manual
Vestil Manufacturing Corp. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868 Fax: (260) 665-1339 Web: www.vestilmfg.com e-mail: info@vestil.com
PEL-88-A-SWA & PEL-100-A-SWA Wrapping Machines Use and Maintenance Manual
VESTIL MANUFACTURING CORP. 999 North Wayne Street, P.O. Box 507, Angola, IN 6703 Telephone: (60) 665-7586 -or- Toll Free (800) 38-0868 Fax: (60) 665-339 www.vestilmfg.com e-mail: sales@vestil.com PEL-88-A-SWA
CART-FP Scissor Carts with 2-Speed Auto-Shifting Foot Pump Instruction Manual
Rev. 4/18/2018 CART-FP, MANUAL Vestil Manufacturing Corp. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868 Fax: (260) 665-1339 Web: www.vestilmfg.com
JIB-FM Series Floor Mounted Jib Cranes Instruction Manual
VESTIL MANUFACTURING CORP. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868 Fax: (260) 665-1339 www.vestilmfg.com e-mail: HUsales@vestil.comU
FHS-Series Steel Fixed Height Gantry Cranes Instruction Manual
24 rev. /5/205 FHS, MANUAL.doc Vestil Manufacturing Corp. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868 Fax: (260) 665-339 Url: www.vestilmfg.com
BEAM CLAMPS INSTRUCTION MANUAL
Beam Clamp Manual 0109 10/7/2010 update BEAM CLAMPS INSTRUCTION MANUAL MODEL BC-2, -4, -6, & -8 VESTIL MANUFACTURING CORP. 2999 NORTH WAYNE STREET, P.O. BOX 507, ANGOLA, IN 46703 TELEPHONE: (260) 665-7586
Instruction Manual. Forklift-Karrier
Instruction Manual Forklift-Karrier Note: The Owner/Operator must read carefully and understand all the information presented in this manual before using this device. - 0 - Contents 1. Figure and Parameter
INSTRUCTION MANUAL MODELS COVERED: CART-300-S-HR, FOR PREMIUM SCISSOR LIFT CARTS CART-600-S-HR,, CART-1000-S-HR, CART-400-D-HR - 1 -
INSTRUCTION MANUAL FOR PREMIUM SCISSOR LIFT CARTS MODELS COVERED: CART-300-S-HR, CART-600-S-HR,, CART-1000-S-HR, CART-400-D-HR - 1 - Content 1. Warning.3 2. Caution..4 3. Name of parts...5 4. Daily inspection
A-LIFT Manual Winch Lift Trucks Instruction Manual
Vestil Manufacturing Corp. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868 Fax: (260) 665-1339 Web: www.vestilmfg.com e-mail: HUsales@vestil.comU
FORK EXTENSIONS, SERIES FE INSTRUCTION MANUAL
FORK EXTENSIONS, SERIES FE INSTRUCTION MANUAL STANDARD FE ROUNDED FE TRIANGULAR FE VESTIL MANUFACTURING CORP. 2999 NORTH WAYNE STREET P.O. BOX 507, ANGOLA, IN 46703 TELEPHONE: (260) 665-7586 -OR- TOLL
STEEL ADJUSTABLE-HEIGHT GANTRY CRANE INSTRUCTION MANUAL
AHS manual 1011 rev. 10/6/011 STEEL ADJUSTABLE-HEIGHT GANTRY CRANE INSTRUCTION MANUAL VESTIL MANUFACTURING CORP. 999 NORTH WAYNE STREET, P.O. BOX 507, ANGOLA, IN 4670 TELEPHONE: (60) 665-7586 -OR- TOLL
LM-Series and LMS-Series Fork Truck Attachments Use and Maintenance Manual
0/ rev. 7/29/204 LM-boom, manual VESTIL MANUFACTURING CORP. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868 Fax: (260) 665-339 www.vestilmfg.com
VESTIL MANUFACTURING CORP. OPERATION & SERVICE MANUAL PORTABLE DRUM JACK (DRUM-55-S) 2999 NORTH WAYNE STREET, P.O. BOX 507, ANGOLA, IN 46703
OPERATION & SERVICE MANUAL PORTABLE DRUM JACK (DRUM-55-S) VESTIL MANUFACTURING CORP. 2999 NORTH WAYNE STREET, P.O. BOX 507, ANGOLA, IN 46703 TELEPHONE: (260) 665-7586 -OR- TOLL FREE (800) 348-0868 FAX:
OPERATION & SERVICE MANUAL DRUM (MANUAL DRUM LIFTER)
OPERATION & SERVICE MANUAL DRUM-55-36 (MANUAL DRUM LIFTER) Vestil Manufacturing Corp. 2999 North Wayne St., Angola, IN 46703 Ph: 260-665-7586. Fax: 260-665-1339 E-mail: Sales@vestil.com Website: www.vestil.com
Rev. 6/16/2015 EMC, MANUAL.doc. EMC-Series Tilting Tables Use and Maintenance Manual
VESTIL MANUFACTURING CORP. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868 Fax: (260) 665-1339 www.vestilmfg.com e-mail: sales@vestil.com
PEL-Series Pallet Handlers Instruction Manual
Rev. 8/3/207 Vestil Manufacturing Corp. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868 Fax: (260) 665-339 www.vestilmfg.com e-mail: sales@vestil.com
SCTAB-500, SCTAB-750D, SCTAB-1000 & SCTAB-2000 SCISSOR LIFT TABLES USE AND MAINTENANCE MANUAL
VESTIL MANUFACTURING CORP. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868 Fax: (260) 665-1339 www.vestilmfg.com e-mail: sales@vestil.com
CART-DC Scissor Carts with Battery-Powered Tabletop Operation and Maintenance Manual
Rev. 4/18/2018 CART-DC, MANUAL Vestil Manufacturing Corp. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868 Fax: (260) 665-1339 Web: www.vestilmfg.com
OWNER'S MANUAL HYDRAULIC DRUM CRUSHER/COMPACTOR MODELS HDC-900 & HDC-905
Vestil Manufacturing Corporation 2999 North Wayne Street, P.O. Box 507 Angola, Indiana 46703 USA Distributed by Ergonomic Partners Email: sales@ergonomicpartners.com Web: www.ergonomicpartners.com PH:
HYDRA SERIES MANUAL HYDRAULIC LIFT TRUCKS ASSEMBLY, USE, AND MAINTENANCE MANUAL
VESTIL MANUFACTURING CORP. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868 Fax: (260) 665-1339 www.vestilmfg.com e-mail: sales@vestil.com
E-TUG SERIES ELECTRIC POWERED TUGGER
E-TUG SERIES ELECTRIC POWERED TUGGER OPERATION AND MAINTENANCE MANUAL E-TUG, Manual VESTIL MANUFACTURING CORP. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 -or- Toll
ALUMINUM ADJUSTABLE-HEIGHT GANTRY CRANE INSTRUCTION MANUAL
AHA manual 1111 rev. 1/5/01 ALUMINUM ADJUSTABLE-HEIGHT GANTRY CRANE INSTRUCTION MANUAL VESTIL MANUFACTURING CORP. 999 NORTH WAYNE STREET, P.O. BOX 507, ANGOLA, IN 4670 TELEPHONE: (60) 665-7586 -OR- TOLL
CART-CTD Scissor Carts with Powered Tabletop and Powered Drive Operation and Maintenance Manual
Vestil Manufacturing Corp. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868 Fax: (260) 665-1339 Web: www.vestilmfg.com e-mail: info@vestil.com
HDC-905 Series Hydraulic Drum Crushers Instruction Manual
HDC-905 Series Hydraulic Drum Crushers Instruction Manual Vestil Manufacturing Corp. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868 Fax:
Before equipment use, please read this operation manual carefully. Serial Number: Date Purchased:
Pushed & Geared Trolleys OPERATION MANUAL This operation manual is intended as an instruction manual for trained personnel who are in charge of installation, maintenance, repair etc. Before equipment use,
01/11 rev. 3/12/2013 LM-series fork-mountable booms
0/ rev. /2/20 LM-series fork-mountable booms FORK-MOUNTED LIFT MASTER BOOMS USE AND MAINTENANCE MANUAL LM-OBT & LM-OBNT LM-HRT & LM-HRNT LM-T & LM-NT LM-EBT & LM-EBNT VESTIL MANUFACTURING CORP. 2999 NORTH
MG12K24T60V4 Mechanical Grapple
170 State Route 271 Attachment Solutions MG12K24T60V4 Mechanical Grapple Operators Manual KENCO Mechanical Grapple Operation Manual 1 TABLE OF CONTENTS 170 State Route 271 Section I. General Information....
INSTRUCTION MANUAL MOBILE LADDER STAND
INSTRUCTION MANUAL MOBILE LADDER STAND LAD-RF MODEL NO. SERIAL NO. VESTIL MANUFACTURING CORP. 2999 NORTH WAYNE STREET, P.O. BOX 507, ANGOLA, IN 46703 TELEPHONE: (260) 665-7586 -OR- TOLL FREE (800) 348-0868
FOR PREMIUM SCISSOR LIFT CARTS MODELS COVERED: CART-300-S-FR, CART-300-D-FR, CART-600-S-FR, CART-600-D-FR, CART-1000-S-FR, CART-1000-D-FR
INSTRUCTION MANUAL FOR PREMIUM SCISSOR LIFT CARTS MODELS COVERED: CART-300-S-FR, CART-300-D-FR, CART-600-S-FR, CART-600-D-FR, CART-1000-S-FR, CART-1000-D-FR Note: Owner/Operator must read and understand
OPERATIONS MANUAL LEVER CHAIN HOIST
OPERATIONS MANUAL LEVER CHAIN HOIST IMPORTANT SAFETY INFORMATION Please read, understand and follow all safety information contained in these instructions prior to the use of this hoist. Retain these instructions
CBS-Series Counterbalanced Stackers Instruction Manual
VESTIL MANUFACTURING CORP. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868 Fax: (260) 665-1339 www.vestilmfg.com e-mail: sales@vestil.com
4/12/2017 SWA-48, MANUAL. SWA-48 and SWA-48-PMO Instruction Manual
Vestil Manufacturing Corp. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868 Fax: (260) 665-339 www.vestilmfg.com e-mail: info@vestil.com SWA-48
Installation and Maintenance Manual for SPANCO A Series Aluminum Gantry Cranes
Manual No. 103-0008 REV. 6/11 Installation and Maintenance Manual for SPANCO A Series Aluminum Gantry Cranes ISO 9001 REGISTERED SPANCO, Inc. 2 TABLE OF CONTENTS Warnings... 3 Installation... 4 Maintenance...
03/10/03 10/10/2017 T-HOP, MANUAL
Vestil Manufacturing Corp. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868 Fax: (260) 665-1339 Website: www.vestilmfg.com Email: info@vestil.com
Provided by: Operating, Maintenance & Parts Manual
Provided by: www.hoistsdirect.com TB681.qxd 11/29/2004 3:04 PM Page 1 Operating, Maintenance & Parts Manual TB603 Manually Lever Operated Chain Hoist 1100 POUNDS MAXIMUM CAPACITY (500 kg) Follow all instructions
LIFT-O-FLEX Lift-O-Turn LIFTER USER MANUAL. We re here for you. PLACE SERIAL NUMBER LABEL HERE. Have Questions?
PLACE SERIAL NUMBER LABEL HERE LIFT-O-FLEX Lift-O-Turn LIFTER USER MANUAL DOCUMENT ID: 01022018 Have Questions? We re here for you. R ON I READ BEFORE YOU BEGIN It is important that you read and understand
Installation and Parts Manual for SPANCO E Series Gantry Cranes
Manual No. 103-0004 REV. 1/10 Installation and Parts Manual for SPANCO E Series Gantry Cranes ISO 9001 REGISTERED SPANCO, Inc. TABLE OF CONTENTS Warnings... 3 Assembly Instructions... 4 Serial Number Location...
Operating Instructions and Parts Manual 3-1/2 ton Farm Jack Model FJ-3-1/2A
Operating Instructions and Parts Manual 3-1/2 ton Farm Jack Model FJ-3-1/2A JET 427 New Sanford Road LaVergne, Tennessee 37086 Part No. M-440436 Ph.: 800-274-6848 Revision A1 06/2014 www.jettools.com Copyright
CB-PMPS Series Counterbalanced Pallet Handlers Instruction Manual
VESTIL MANUFACTURING CORP. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868 Fax: (260) 665-1339 www.vestilmfg.com e-mail: sales@vestil.com
Jib Crane for Bucket Elevators. Installation and Operation Manual PNEG Date: Version: 2.0 PNEG-1783
Jib Crane for Bucket Elevators Installation and Operation Manual PNEG-1783 Version: 2.0 Date: 11-25-15 PNEG-1783 42" Pulley with 14 x 22 and 14 x 26 Trunking 48" Pulley with 14 x 26 Trunking All information,
S3-125-AA -DOUBLE MAST-STACKER FULLY POWERED
Rev. 0213 EPT, Manual.doc VESTIL MANUFACTURING CORP. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868 Fax: (260) 665-1339 www.vestilmfg.com
Owner s (Operator s) Manual & Safety Instructions Manually Lever Operated Chain Hoist Model LX1B
Owner s (Operator s) Manual & Safety Instructions Manually Lever Operated Chain Hoist Model LX1B BULLETIN NO. LX-0804-CE-06 WARNING This equipment must not be installed, operated or maintained by any person
TONS. Before each shift: Before operating: Before initial operation of hoist:
LEVER HOIST 0.25 9 TONS Manual Notice It is the responsibility of the owner/user to install, inspect, test, maintain, and operate these lever hoists in accordance with ASME B30.21, Safety Standard for
Amarr SuperFlex. Installation Instructions and Owner's Manual. Entrematic 165 Carriage Court Winston Salem, NC
Entrematic 165 Carriage Court Winston Salem, NC 27105 www.amarr.com 877-512-6277 Amarr SuperFlex Installation Instructions and Owner's Manual Do not install, operate or service this product unless you
The Kenlift. Attachment Solutions
Attachment Solutions The Kenlift Concrete median barrier handling device Operators Manual Conforms to ASME B 30.20, BTH-1 Design Category B, Service Class 3 TABLE OF CONTENTS Section I. General Information....
Extension Hopper Installation & Operator s Instruction Manual for Model 55, 75, 90, & HMC FLEX-AUGER Feed Delivery Systems
Extension Hopper Installation & Operator s Instruction Manual for Model 55, 75, 90, & HMC FLEX-AUGER Feed Delivery Systems April 02 Chore-Time Warranty Chore-Time Equipment warrants each new product manufactured
Engine Crane. Operating Instructions & Parts Manual
Engine Crane Operating Instructions & Parts Manual Model HW93809 Maximum Rated Capacity 2 Ton This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety
Installation and Parts Manual for SPANCO A Series Steel Gantry Cranes
Manual No. 103-0002 REV. 3/07 Installation and Parts Manual for SPANCO A Series Steel Gantry Cranes ISO 9001 REGISTERED 2 TABLE OF CONTENTS Warnings... 3 Assembly and Operation...4 Track Installation Instructions...6
1000-LB. ENGINE STAND
1000-LB. ENGINE STAND WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions may result in
Spare Parts, Instruction and Maintenance Manual for SPANCO Model 301 Jib Cranes
Manual No. 103-0007 REV. 6/10 Spare Parts, Instruction and Maintenance Manual for SPANCO Model 301 Jib Cranes ISO 9001 REGISTERED SPANCO, Inc. 2 TABLE OF CONTENTS Forward... 4 Installation... 4-6 Maintenance...
2000-LB. ENGINE STAND
2000-LB. ENGINE STAND WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions may result in
Model 90 Twin Control Unit
Model 90 Twin Control Unit Installation Manual MAY 02 Model 90 Twin Control Unit Installation Manual Page 1 MA1277B Warranty Information Chore-Time Equipment, a division of CTB, Inc., ("Chore-Time") warrants
BELOW-THE-HOOK & MATERIAL HANDLING EQUIPMENT
BELOW-THE-HOOK & MATERIAL HANDLING EQUIPMENT lifting EQUIPMENT Tongs HBTF Bar Tong Fixed... Page 62 TONGS HBTA Bar Tong Adjustable... Page 63 lifting EQUIPMENT HBTF BAR TONG FIXED FEATURES This style of
1/2-TON MANUAL CHAIN HOIST
1/2-TON MANUAL CHAIN HOIST Owner s Manual WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions
Operating Instructions & Parts Manual
Forklift Jack Operating Instructions & Parts Manual Model Number HW93659 Capacity 4 Ton Made in the U.S.A.! This is the safety alert symbol. It is used to alert you to potential personal injury hazards.
LX MINI PULLER OWNER S MANUAL 1/4 and 1/2 Ton Capacities Effective: May 19, 2017
LX MINI PULLER OWNER S MANUAL 1/4 and 1/2 Ton Capacities Effective: May 19, 2017 WARNING This equipment should not be installed, operated or maintained by any person who has not read and understood all
On-A-Roll Lifter Instruction Manual for Standard Models Read Before Use!
On-A-Roll Lifter Instruction Manual for Standard Models Read Before Use! Important instructional, safety and precautionary information! It is the user s responsibility to exercise good judgment, common
MANUAL HYDRAULIC LIFT TRUCKS INSTRUCTION MANUAL
MANUAL HYDRAULIC LIFT TRUCKS INSTRUCTION MANUAL HYDRA-2 HYDRA-4 HYDRA-HD MODEL NO. SERIAL NO. VESTIL MANUFACTURING CORP. 2999 NORTH WAYNE STREET, P.O. BOX 507, ANGOLA, IN 46703 TELEPHONE: (260) 665-7586
Owner s Manual. Powered Dandy Lifts PLM-100, PLM100W, PLM150, PLM-150W. (See separate manual for PLM-250) Model # Serial #
Owner s Manual Powered Dandy Lifts PLM-00, PLM00W, PLM50, PLM-50W (See separate manual for PLM-250) Model # Serial # Southworth Products Corp P.O. Box 380/Portland, Maine 0404-380 Phone 800-743-000 FAX
Owner s Manual Gantry Cranes
Owner s Manual Gantry Cranes Fixed Height Gantry Crane MODEL NUMBER: SERIAL NUMBER: CAPACITY IN TONS: Telescoping Gantry Crane Bushman Equipment, Inc. 262-790-4200, 800338-7810, Fax 262-790-4200 www.bushman.com
500kg HYDRAULIC TABLE LIFT
Product Code: 6007T OWNER S MANUAL PRODUCT CODE: 6007T 500kg HYDRAULIC TABLE LIFT Working Load Limit 500kg Maximum Height 1575mm Minimum Height 440mm Table Dimensions 1010x520mm Wheel Diameter 150mm Made