INSTALLATION INSTRUCTIONS
|
|
- Myra Imogen Cole
- 5 years ago
- Views:
Transcription
1 VOLVO THREADED FRONT LEAF SPRING BUSHING IMPORTANT INFORMATION AND SAFETY PRECAUTIONS This product will provide excellent service life when it has been properly installed and maintained. 1 OF 6 Read the instructions carefully. Pay particular attention to the NOTE sections which contain helpful information to make the installation as easy as possible. Also pay close attention to the sections with the following warning symbol next to them: These are provided to help avoid personal injury, property damage or to prevent future safety problems with the vehicle. In addition, we recommend that you strictly adhere to all federal and state approved shop safety practices and procedures. Carefully inspect the vehicle suspension that is being repaired. Correct or replace all defective components. REQUIRED TOOLS The PT91500 drive handle and PT91118 alignment nose are required when installing the Atro threaded leaf spring bushings. In addition, the PT threaded pin drive tool, or a spanner wrench, will be needed to install the threaded stainless steel pin into the Atro threaded leaf spring bushings. NOTE: Be sure to use the proper Atro leaf spring bushing installation tool. Use of the wrong tool may damage the bushing assembly and void your warranty. REMOVAL OF OLD COMPONENTS - FRONT OF FRONT SPRING EYE Always wear safety glasses and any other necessary safety gear while performing this procedure to protect against bodily injury. Overheating the spring eye could weaken the spring resulting in a premature failure. 1. Securely support the vehicle to remove the weight off of the front leaf springs 2. Remove the old front of front spring pin and spring eye bushing. NOTE: It is not necessary to completely remove the leaf spring from the axle. ATRO LEAF SPRING BUSHING INSTALLATION - FRONT OF FRONT SPRING EYE Always wear safety glasses and any other necessary safety gear while performing this procedure to protect against bodily injury. If the leaf spring eye was heated during bushing removal, allow it to cool before installing the Atro leaf spring bushing. This will prevent overheating of the bushing/polyurethane material. Overheating of the material could lead to premature failure. Inspect the leaf spring eye for cracks, out-of-round or worn out bore conditions. If any of these conditions exist, replace the damaged components. Failure of any of these components could result in an accident, serious property damage and severe injury or death.
2 VOLVO THREADED FRONT LEAF SPRING BUSHING 2 OF 6 1. Remove all burrs and corrosion from the spring eye with a file, hone or wire brush and wipe clean. 2. Measure spring eye ID. Recommended basic ID should be between and If ID is too large, replace spring. If ID is too small, make sure all corrosion and contamination are removed from spring eye. 3. Remove one of the plastic plugs from one end of the Atro leaf spring bushing. Do not remove plastic plug in opposite end of bushing until bushing is installed. This will help prevent contamination from getting inside the bushing during the installation process. 4. Insert the bushing drive tool into the Atro leaf spring bushing. (Refer to Figure 1) 5. Align Atro leaf spring bushing with bore of spring eye. Using a press (preferred), draw bolt, or impact hammer, install the bushing in the spring eye. 6. Remove second plastic plug. NOTE: The Atro leaf spring bushings come pre-lubricated with special break-in grease. It is NOT necessary to re-lubricate these bushings during their service life. FIGURE 1 FRONT SPRING BRACKET SPRING EYE BUSHING BUSHING DRIVE TOOL ATRO THREADED SPRING PIN INSTALLATION - FRONT OF FRONT SPRING EYE 1. Check bracket/spring alignment. If spring and bracket are out of alignment, correct alignment before continuing. 2. Remove any contaminants, such as rust or dirt, which may have been deposited in the inner diameter of the bushing during installation. NOTE: Do NOT remove grease from spring eye bushing. 3. Align bore of spring eye bushing with the spring pin holes in hanger bracket. (Refer to Figure 2)
3 VOLVO THREADED FRONT LEAF SPRING BUSHING 3 OF 6 FIGURE 2 SPRING PIN LOCK BOLT THREADED SPRING PIN 4. Insert threaded spring pin through hanger bracket into spring eye bushing. 5. Using the Atro PT threaded pin drive tool, or a spanner wrench, thread the pin into the bushing and hanger bracket until grooves in threaded pin line up with spring pin lock bolt holes in bracket. Note: Do NOT use air tools to tighten locking nuts. A torque wrench must be used to attain the required torque and precent over tightening. 6. Insure there is an equal amount of space between edge of spring and hanger bracket on both sides of the spring (center spring in bracket). Thread spring pin in or out to adjust spacing. Doing this will prevent the spring from rubbing against the hanger bracket during use. 7. Insert NEW spring pin lock bolts and nuts, torque to ft-lbs. NEVER reuse old bolts and nuts. REMOVAL OF OLD COMPONENTS - REAR OF FRONT SPRING EYE Always wear safety glasses and any other necessary safety gear while performing this procedure to protect against bodily injury. Overheating the spring eye could weaken the spring resulting in premature failure. 1. Securely support the vehicle to remove the weight off of the front leaf springs. 2. Remove the old shackle assembly. NOTE: It is not necessary to competely remove the leaf spring from the axle.
4 VOLVO THREADED FRONT LEAF SPRING BUSHING ATRO LEAF SPRING BUSHING INSTALLATION - REAR OF FRONT SPRING EYE & BRACKET Always wear safety glasses and any other safety gear while performing this procedure to protect against bodily injury. If the leaf spring eye or bracket were heated during bushing removal, allow them to cool before installation of Atro leaf spring bushings. This will prevent overheating of the bushing/polyurethane material. Overheating of material could lead to premature failure. Inspect the frame hanger bracket and the leaf spring eye for cracks, out-of-round or worn out bore conditions. If any of these conditions exist, replace the damaged components. Failure of any of these components could result in an accident, serious property damage and severe injury or death. 1. Remove all burrs and corrosion from the spring eye and bracket with a file, hone or wire brush and wipe clean. 2. Measure spring eye ID. Recommended basic ID should be between and If ID is too large, replace spring. If ID is too small, make sure all corrosion and contamination are removed from spring eye. 3. Remove one of the plastic plugs from the end of the Atro leaf spring bushing. Do not remove plastic plug in opposite end of bushing until bushing is installed. This will help prevent contamination getting inside the bushing during the installation process. 4. Insert the bushing drive tool into the Atro leaf spring bushing. (Refer to Figure 3) 5. Align Atro leaf spring eye bushing with bore of rear spring eye. 6. Using a press (preferred), draw bolt or impact hammer, install the bushing into the rear spring eye. 7. Remove second plastic plug. 8. Repeat steps 3-6 to install an Atro leaf spring bushing into the frame hanger bracket. 9. If the hanger has been removed, reinstall following the manufacturers instructions. NOTE: The Atro leaf spring bushings come pre-lubricated with a special break-in grease. It is NOT necessary to re-lubricate these bushings during their service life. FIGURE 3 4 OF 6 FRAME HANGER BRACKET BUSHING DRIVE REAR SPRING EYE SPRING EYE BUSHING Do not weld the Atro leaf spring bushing into the leaf spring eye. Welding the Atro leaf spring bushing will damage it and VOID warranty.
5 VOLVO THREADED FRONT LEAF SPRING BUSHING 5 OF 6 ATRO THREADED SPRING PIN INSTALLATION - REAR OF FRONT 1. Remove any contaminants, such as rust or dirt, which may have been deposited in the inner diameter of the bushing during installation. NOTE: Do NOT remove grease from spring eye bushing. 2. Using the Atro PT threaded pin drive tool, or a spanner wrench, thread a spring pin into both the hanger bracket and rear spring eye bushings until it is centered. NOTE: Do NOT use an impact tool to thread spring pin into bushing. NOTE: The spring pin in the hanger bracket and the rear spring eye must be threaded in from the oppoite directions in order for the side bars to fit properly. (Refer to figure 4) SIDE BAR INSTALLATION 1. Make sure the grooves in the small end of the spring pins are aligned horizontally so the side bar lock bolts will slide through them. Install the side bars on the ends of the pins protruding from the spring eye bushings. (Refer to Figure 4) FIGURE 4 SIDE BAR LOCK BOLTS SIDE BAR Inspect side bars for excessive wear. If necessary, replace side bars with Volvo side bar #: Failure to do so could result in an accident, serious property damage and severe injury or death. 2. Install NEW side bar lock bolts and locking nuts. Do not tighten yet! (Refer to Figure 4) 3. Insure there is an equal amount of space between edge of spring and side bars on both sides of the spring. Also insure there is an equal amount of space between edge of hanger bracket and side bars on both side of the hanger bracket. Thread spring pins in or out to adjust spacing (two side barlock bolts on the small end of the pins will have to be removed in order to rotate spring pin). Doing this will prevent the sidebars from rubbing against the hanger bracket or spring during use. 4. Torque side bar lock bolts to ft-lbs. NEVER reuse old bolts and nuts.
6 VOLVO THREADED FRONT LEAF SPRING BUSHING FRONT END ALIGNMENT After installing the Atro leaf spring bushing, it may be necessary to perform a front end alignment check for caster, camber and toe-in. Use the manufacturers guidelines and specifications for performing this task. MAINTENANCE The Atro leaf spring bushings are self-lubricating and virtually maintenance free. The spring, hanger bracket, side bars, and Atro leaf spring bushings should be visually inspected during every oil change. Also, the lock bolts should be re-torqued periodically to insure the integrity of the leaf spring bushings. WARRANTY NOTICE Follow the guidelines below to take full advantage of your Atro spring eye bushing warranty. Failure to do so could void your warranty and may lead to premature failure, damages and/or injuries. DO NOT use alternate components and/or hardwar in conjunction with Atro spring eye bushings Always use matching Atro components on both sides of the vehicle DO NOT exceed the 20,000lb GAWR Use proper installation tools and installation methods (see installation instructions) DO NOT expsose Atro spring eye bushings to excessive heat (i.e. welding or torch use) Atro Engineered Systems, Inc. can not be held responsible for any failure, damages or injuries that may result from not adhering to these guidelines. 6 OF 6 POLYURETHANE PARTS SOLUTIONS FOR HEAVY TRUCKS Atrobushing.com 2017 Atro Engineered Systems, Inc. 6 Bolte Lane St. Clair, Missouri U.S.A. (800) Fax (866)
SHACKLE INSTALLATION INSTRUCTIONS
SHACKLE INSTALLATION INSTRUCTIONS Read and understand all instructions, warnings, cautions, and notes in this sheet and in your owners manual before you begin the installation of this shackle kit. Proper
More informationINSTALLATION INSTRUCTIONS FOR PLEASE READ AND UNDERSTAND TERMS/POLICIES BEFORE YOU INSTALL THIS SYSTEM
MOUNTAIN OFF ROAD ENTERPRISES. LLC. P.O. BOX 690 DELTA, COLORADO 81416 970-625-0500 E-mail: info@mountainoffroad.com www.mountainoffroad.com INSTALLATION INSTRUCTIONS FOR 8795-2 PLEASE READ AND UNDERSTAND
More information5 inch lift kit. WILL FIT E-Z-GO RXV installation instructions. Main Bracket Spindles Shock Mount Brackets Rear Shock Plates Rear Lift Blocks
PART# 18142 included: 5 inch lift kit WILL FIT E-Z-GO RXV installation instructions Main Bracket Spindles Shock Mount Brackets Rear Shock Plates Rear Lift Blocks WARNING: After installing this lift kit,
More informationInstallation Instructions
86-95 Low Range Off Road Universal Front Shock Tower Kit for Suzuki Samurai (SKU# SSP-UST) Installation Instructions Revised 10/29/13 Suggested Tools: CAUTION: Safety glasses should be worn at all times
More informationINSTALLATION INSTRUCTIONS FOR PLEASE READ AND UNDERSTAND TERMS/POLICIES BEFORE YOU INSTALL THIS SYSTEM
MOUNTAIN OFF ROAD ENTERPRISES. INC. P.O. BOX 690 DELTA, COLORADO 81416 970-625-0500 E-mail: info@mountainoffroad.com www.mountainoffroad.com INSTALLATION INSTRUCTIONS FOR 8795-3 PLEASE READ AND UNDERSTAND
More informationInstallation Instructions
Instructions Created by an: 1986-1995 Toyota Pickup 4Runner Hilux Front Ball Joint Spacer Kit - 2.5" 64mm Lift by Low Range Off-Road (SKU# TSP-BJS-1.5 & TSP-BJS-1.5-W/Shocks) Installation Instructions
More informationInstallation Instructions
Instructions Created by an: Revised 7-11-17 LRT 2005-2017 3/1 Leveling/ Lift Kit for Toyota Tacoma by Low Range Off-Road (SKU# LR-LRTACO) Installation Instructions Suggested Tools: CAUTION: Safety glasses
More informationINSTALLATION INSTRUCTION 88092
INSTALLATION INSTRUCTION 88092 FOR RANCHO SUSPENSION SYSTEM RS6592: NISSAN XTERRA & 2WD FRONTIER READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION Rev C IMPORTANT NOTES!
More informationInstallation Instructions
86-95 Suzuki Samurai Front Shackle (SKU# SSP-HDS1) Note: These instructions also apply to SKU# SSP-HDS3 Installation Instructions Suggested Tools: CAUTION: Safety glasses should be worn at all times when
More informationINSTALLATION INSTRUCTIONS FOR M.O.R.E. SHACKLE REVERSAL SYSTEM (S.R.S. ) PART # THIS SYSTEM FITS Jeep CJ-5, CJ-7, CJ-8 VEHICLES.
INSTALLATION INSTRUCTIONS FOR M.O.R.E. SHACKLE REVERSAL SYSTEM (S.R.S. ) PART # 7686-6 THIS SYSTEM FITS 1976-1986 Jeep CJ-5, CJ-7, CJ-8 VEHICLES. Please read all instructions carefully (including terms-policies)
More informationInstallation Instructions
86-95 Suzuki Samurai Replacement U-bolts, Stock and Extended Length (SKU# SSP-UB) Installation Instructions CAUTION: Safety glasses should be worn at all times when working with vehicles and related tools
More informationMS2200, MS2500, and MS3000 Suspension Installation Manual ON/OFF HIGHWAY SUSPENSION SYSTEM
MS22, MS25, and MS3 Suspension Installation Manual ON/OFF HIGHWAY SUSPENSION SYSTEM 972.547.62 8.445.736 FAX: 972.542.97 725 E. UNIVERSITY ST. McKINNEY, TEXAS 7569 www.watsonsuspensions.com Watson & Chalin
More information1988 Chevrolet Pickup V SUSPENSION - FRONT (4WD)' 'Front Suspension - "V" Series 1988 SUSPENSION - FRONT (4WD) Front Suspension - "V" Series
1988 SUSPENSION - FRONT (4WD) Front Suspension - "V" Series DESCRIPTION NOTE: Vehicle serial numbers used in this article has been abbreviated for common reference to Chevrolet and GMC models. Chevrolet
More informationTorque Settings. 5/ ft lbs. 3/ ft lbs. 7/ ft lbs. 1/ ft lbs. 9/ ft lbs. 5/ ft lbs. 3/ ft lbs.
INSTALLATION MANUAL 2 OR 4 FRONT AND REAR SPRING SUSPENSION SYSTEM CHEVY PICKUP & BLZR 1/2 3/4 TON 1969 1972 PART # 14611 SJ052802 PART NUMBER : 14611 1969 1972 CHEVY PICK UP & BLAZER 1/2 OR 3/4 TON 2
More informationTC Series Front Axle. TC Series Front Axle 010-1
TC Series Front Axle Blue Bird Corporation assumes sole responsibility for ensuring that the information provided herein is accurate to the best of its knowledge at the time of printing. In keeping with
More informationINSTALLATION MANUAL 4 SUSPENSION SYSTEM CHEVY PICKUP 3/4 TON PART # 14720
INSTALLATION MANUAL 4 SUSPENSION SYSTEM CHEVY PICKUP 3/4 TON 1973 1987 PART # 14720 SJ051402 PART NUMBER : 14720 1973 1987 CHEVY PICK UP 3/4 TON 4 SUSPENSION SYSTEM / WITH REAR BLOCKS PARTS LIST: Part
More informationTorque Settings. 5/ ft lbs. 3/ ft lbs. 7/ ft lbs. 1/ ft lbs. 9/ ft lbs. 5/ ft lbs. 3/ ft lbs.
INSTALLATION MANUAL 2, 3 OR 4 FRONT AND REAR SPRING SUSPENSION SYSTEM CHEVY PICKUP & BLAZER 1/2 TON 1973 1987 PART # 14711 SJ052102 PART NUMBER : 14711 1973 1987 CHEVY PICK UP & BLAZER 1/2 TON 2, 3 OR
More informationTorque Settings. 5/ ft lbs. 3/ ft lbs. 7/ ft lbs. 1/ ft lbs. 9/ ft lbs. 5/ ft lbs. 3/ ft lbs.
INSTALLATION MANUAL 6 FRONT AND REAR SPRING SUSPENSION SYSTEM CHEVY PICKUP 3/4 TON 1973 1987 PART # 16721 SJ052102 PART NUMBER : 16721 1973 1987 CHEVY PICK UP 3/4 TON 6 SUSPENSION SYSTEM FRONT AND REAR
More informationPart # WD & 2WD Jeep XJ Cherokee 3 Lift Now Manufactured With Chromolly Arms PRO COMP SUSPENSION. Suspension Systems that Work!
PRO COMP SUSPENSION Suspension Systems that Work! Part # 55590 84-01 4WD & 2WD Jeep XJ Cherokee 3 Lift Now Manufactured With Chromolly Arms This document contains very important information that includes
More informationFTS21031BK Rear Leaf Spring Hanger GM 2500 HD 4WD
4331 EUCALYPTUS AVE. ~~ CHINO, CA 91710 909-597-7800 Fax 909-597-7185 FTS21031BK Rear Leaf Spring Hanger 2001-2006 GM 2500 HD 4WD PARTS LIST: Qu a Part # Description 1 FT20250BK Front Hanger Bracket Driver
More informationOperation & Maintenance Instruction , S.9. MARCH, 2005 Supersedes issue dated March, 2003
S-1 LOAD SENSOR VALVES, SUSPENSION MOUNTING - PART NO. 664801-0001 SUSPENSION MOUNTING - PART NO. 665132-0001 FLOOR MOUNTING - PART NO. 664801-0002 FLOOR MOUNTING - PART NO. 665132-0002 MARCH, 2005 Supersedes
More informationS-1 LOAD SENSOR VALVES, PART NOS & PART NOS &
S-1 LOAD SENSOR VALVES, PART NOS. 578553-0001 & 578553-0011 PART NOS. 665133-0001 & 665133-0011 AUGUST, 2005 Supersedes issue dated December, 2004 NOTE: The following description and operation is based
More informationSuzuki Samurai to Toyota Front Spring Swap Kit, with Missing Link Shackles (SKU#SSP-TSFM) Installation Instructions
Suzuki Samurai to Toyota Front Spring Swap Kit, with Missing Link Shackles (SKU#SSP-TSFM) Installation Instructions CAUTION: Safety glasses should be worn at all times when working with vehicles and related
More informationDODGE 3 SUSPENSION LIFT KIT
921351200 Kit Contents: 9280:Front Coil Springs 1351BOX1: Upper Control Arms Lower Control Arms Sway bar Brackets Brake Proportioning Valve Bracket Track Bar Relocation Bracket 1351BOX2: 5.75 Blocks U-bolt
More information"N-1-A" REDUCING VALVE, Part No with "N" REDUCING VALVE PORTION, Part No
"N-1-A" REDUCING VALVE, Part No. 528348 with "N" REDUCING VALVE PORTION, Part No. 529445 DECEMBER, 1984 NOTE: The following description and operation is based on this device and its components being new
More information4331 EUCALYPTUS AVE. ~~ CHINO, CA Fax FORD F-250/350 SUPER DUTY 4 WHEEL DRIVE
4331 EUCALYPTUS AVE. ~~ CHINO, CA 91710 909-597-7800 Fax 909-597-7185 2001-2004 FORD F-250/350 SUPER DUTY 4 WHEEL DRIVE 2000-03 EXCURSION 4 WHEEL DRIVE FTS424-1BK 3.5 LIFT BOX KIT PARTS LIST: 1 EA. FRT.
More informationBefore beginning this installation read the instruction sheet thoroughly. Check that all parts on parts list are present.
INSTALLATION INSTRUCTIONS C2085 SLIDE-A-LINK, FORD F-150/LIGHTNING The Slide-A-Link by Competition Engineering is designed for use in 2 Wheel Drive Ford Lightning Pickups. The rigid front mount assembly
More informationRUGBY HOIST CYLINDERS SERVICE BULLETIN
TRUCK BODIES & EQUIPMENT INTERNATIONAL, Inc. Website: www.rugbymfg.com E-mail: sales@rugbymfg.com Phone: (701) 776-5722 Toll Free: (800) 869-9162 RUGBY HOIST CYLINDERS SERVICE BULLETIN This bulletin applies
More informationSuperTrac. Axle. Service & Maintenance. Manual
SuperTrac Axle Service & Maintenance Manual Table of Contents Page Exploded Views Section 1: General Information General Warnings Description of Axle Models Identifications Section 2: Installation Axle
More informationTorque Settings INSTALLATION MANUAL 3 SUSPENSION SYSTEM CHEVY PICKUP 3/4 TON PART # 13720
INSTALLATION MANUAL 3 SUSPENSION SYSTEM CHEVY PICKUP 3/4 TON 1973 1987 PART # 13720 SJ050702 PART NUMBER : 13720 1973 1987 CHEVY PICK UP 3/4 TON 3 SUSPENSION SYSTEM / WITH REAR BLOCKS PARTS LIST: Part
More informationTechnical Support Line: (952) Hanover Ave. Lakeville, MN
Technical Support Line: (952) 985-5675 Email: Sales@QA1.net 21730 Hanover Ave. Lakeville, MN 55044 www.qa1.net INSTALLATION INSTRUCTIONS QA1 1967-1979 Mopar A-Body Rear 6 link Conversion System QA1 p/n
More informationMODCO TM FIGURE 500 CLOSURE
CLOSURE SPECIALISTS SINCE 1981 MODCO TM FIGURE 500 CLOSURE INSTALLATION INSTRUCTIONS (!) THE INFORMATION PROVIDED IN THIS DOCUMENT IS VERY IMPORTANT (!) & (!) needs to be shared with everyone involved
More informationInstallation Instructions
Suzuki Samurai 26 Spline Lockright Locker w/o Couplers (SKU# SAX-1510) Installation Instructions Suggested Tools: CAUTION: Safety glasses should be worn at all times when working with vehicles and related
More informationWD DODGE SUSPENSION LIFT KIT P/N
4/03/03 94-01 4WD DODGE 1500 3 SUSPENSION LIFT KIT P/N 10-46094 NOTE: Each lift kit, and options to lift kits, are packaged separately. Therefore installation procedures are covered in separate instructions.
More informationInstallation Instructions
Preparing your vehicle to install your brake system upgrade 1. Rack the vehicle. 2. If you don t have a rack, then you must take extra safety precautions. 3. Choose a firmly packed and level ground to
More informationINSTALLATION MANUAL 6 FRONT AND REAR SPRING SUSPENSION SYSTEM CHEVY PICKUP & BLZR 1/2 3/4 TON PART #
INSTALLATION MANUAL 6 FRONT AND REAR SPRING SUSPENSION SYSTEM CHEVY PICKUP & BLZR 1/2 3/4 TON 1969 1972 PART # 16611 SJ052102 PART NUMBER : 16611 1969 1972 CHEVY PICK UP & BLAZER 1/2 OR 3/4 TON 6 FRONT
More informationSuspension. Table of Contents
Suspension Table of Contents Sub-Headings Safety Notice 2 Explanation of Signal Words 2 Danger 2 2 Caution 2 Description 3 Preventive Maintenance 4 Shock Absorber 7 Visual Inspection 7 Heat Test 8 Steering
More information4331 EUCALYPTUS AVE. ~~ CHINO, CA Fax FORD F-250/350 SUPER DUTY 4 WHEEL DRIVE FTS
4331 EUCALYPTUS AVE. ~~ CHINO, CA 91710 909-597-7800 Fax 909-597-7185 2000-2003 FORD F-250/350 SUPER DUTY 4 WHEEL DRIVE FTS421-1 5.5 & 8 LIFT BOX KIT PARTS LIST: 1 EA. TRACK ARM BRKT. FT423-100 1 EA. PITMAN
More informationEqua-Flex Tandem and Triple OEM INSTALLATION MANUAL
Equa-Flex Tandem and Triple OEM INSTALLATION MANUAL TABLE OF CONTENTS System Information 2 Tandem Axle Options 2 Triple Axle Options 2 Safety Information 2 Resources Required 3 Installation 3 Tandem Axle
More informationIFS Eliminator Kit,
IFS Eliminator Kit, 110001-1 IFS Eliminator Kit Contents: Front Leaf Springs (choice 3", 4", or 5") 1.0 High Steer Crossover Steering Kit 1.0 Frame Tube Jig Kit 1.0 Steering Stabilizer Kit 1.0 U-bolt Flip
More information4331 EUCALYPTUS AVE. ~~ CHINO, CA TEL FAX
www.fabtechmotorsports.com 4331 EUCALYPTUS AVE. ~~ CHINO, CA. 91710 TEL 909-597-7800 FAX 909-597-7185 1995.5 2004 TOYOTA TACOMA OEM PRERUNNER AND 4WD FTS2300K 0-3.5 COIL OVER SYSTEM PARTS LIST: 2 EA. FT2300S
More informationPRODUCT USE INFORMATION
Nissan 2017 Titan 3 Suspension Kit Thank you for choosing Rough Country for all your suspension needs. Rough Country recommends a certified technician install this system. In addition to these instructions,
More informationINSTALLATION MANUAL 6 SUSPENSION SYSTEM PART # CHEVY/GMC BLZR/SUBURBAN 1/2 TON
INSTALLATION MANUAL 6 SUSPENSION SYSTEM CHEVY/GMC BLZR/SUBURBAN 1/2 TON 1988 1991 PART # 16730 SJ051402 PART NUMBER : 16730 1988 1991 CHEVY/GMC BLAZER & SUBURBAN 1/2 TON 6 SUSPENSION SYSTEM WITH REAR BLOCKS
More informationINSTALLATION INSTRUCTION 88051
INSTALLATION INSTRUCTION 88051 For Rancho Suspension System RS6551: Chevrolet 2500 Suburban & 2500 Avalanche READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION Rev C IMPORTANT
More informationRequired tools General hand tools 21/64" drill bit Torque wrench Threadlocker Center punch
Slipper Spring Kit (part numbers 2560, 2570 and 2580) Item Qty Part number Description 1... 8... 350054-50...3/8-16 x 1" grade 8 self-tapping screw 2... 4... 350084-00...7/16-14 x 4" grade 5 3... 6...
More information4 & 6 4-Link Suspension Systems. Ford Super Duty 4WD Part#: ,
Part#: 013013, 013014 4 & 6 4-Link Suspension Systems Ford Super Duty 4WD 2011-2016 Rev. 051817 491 W. Garfield Ave., Coldwater, MI 49036. Phone: 517-279-2135 E-mail: tech-bds@sporttruckusainc.com Read
More information28-A DOUBLE CHECK VALVE PORTION, Pc. No
28-A DOUBLE CHECK VALVE PORTION, Pc. No. 650143 NOVEMBER, 1989 Supersedes issue dated January, 1989 NOTE: The following description and operation is based on this device and its components being new or
More informationRoad Armor Triple Axle Equalizer by Trailair
Road Armor Triple Axle by Trailair OEM INSTALLATION MANUAL Rev: 06.26.2017 Page 1 TABLE OF CONTENTS System Information 2 Triple Axle Options 2 Safety Information 2 Resources Required 2 Installation 3 Rear
More informationWARNING indicates a potentially hazardous situation which, if not avoided, could result in property damage, serious personal injury or even death.
Comfort Ride Third axle slipper leaf spring system (part numbers 2560-50, 2570-50 and 2580-50) and shock absorber system (part numbers 2450-50, 2460-50 and 2470-50) Installation Instructions All specifications
More informationINSTALLATION INSTRUCTIONS
214205 INSTALLATION INSTRUCTIONS 8-27-2015 REV.A PART # DESCRIPTION 7929 Lincoln Ave. Riverside, CA 92504 Phone: 951.689.ICON Fax: 951.689.1016 214205 14-UP RAM 2500 4.5 BOX KIT COMPONENTS INCLUDED (1)
More informationLIFT Standard A-Arm Lift Kit Club Car Precedent Installation Instructions
LIFT-563 6 Standard A-Arm Lift Kit Club Car Precedent Installation Instructions Contents of LIFT-563 Club Car Precedent Lift Kit: a (1 ea.) Front Suspension b (1 ea.) Driver Side Upper A-Arm c (1 ea.)
More informationChrysler A-Body Tubular A-Arms Installation Instructions A-ARM INSTALLATION
1967-1976 Dodge Demon 1112 67-72 Chrysler A-Body Tubular A-Arms Installation Instructions Thank you for your purchase of this Hotchkis Performance product. Your A-Arm set was designed with the performance
More informationInstallation Instructions
86-89 Suzuki Samurai Pedal Rebuild Kit SKU# SIB-PRB! Instructions also includes clutch adjustment procedures. Installation Instructions W e a l s o s u p p l y replacement peddle pads. Click HERE for more
More information& 6 XJ CHEROKEE LONG ARM KIT
92PERF1689 84-01 4.5 & 6 XJ CHEROKEE LONG ARM KIT Thank you for choosing Rough Country for your suspension needs. Rough Country recommends a certified technician installs this system. In addition to these
More informationRear Axle Single-Reduction Carrier
Revised 08-0 Rear Axle Single-Reduction Carrier Model MS-3 Maintenance Manual MM-030 Service Notes Service Notes Notes About This Manual This manual provides instructions for Meritor s model MS-3 single-reduction
More informationRhino Long Travel Spindle Kit Yamaha Rhino FTR10072
4331 EUCALYPTUS AVE. ~~ CHINO, CA 91710 909-597-7800 Fax 909-597-7185 Rhino Long Travel Spindle Kit 2005-08 Yamaha Rhino FTR10072 PARTS LIST: QTY. Part # Description 1 FTS95061D Rhino Spindle Driver 1
More informationInstallation Instructions
86-95 Suzuki Samurai Rear Wheel Bearing Kit (SKU# SAX-RWB) Instructions also include:! Rear Hub Bolt Kit!!!! (SKU# SAX-AS)!! SJ410 Backing Plate!!!! (SKU# SAX-410)! SJ413 Rear Drum Brake Hardware Kit!
More informationGM P/U, Blazer, Suburban, 1 Ton 4WD 4-6 Kits
92114500 1973-87 GM P/U, 1973-91 Blazer, Suburban, 1 Ton 4WD 4-6 Kits Thank you for choosing Rough Country for all of your suspension needs. Rough Country recommends a certified technician installs this
More informationFRONT SHOCK ABSORBER
FRONT SHOCK ABSORBER INSTALLATION AND USER S INSTRUCTIONS Thank you for purchasing a MAZDASPEED accessory. Before removal and installation, be sure to thoroughly read these instructions. Please read the
More informationINSTALLATION INSTRUCTION 88578
INSTALLATION INSTRUCTION 88578 For Rancho Suspension System RS6579B: 4WD Dodge 1500 & 2500 READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION Rev E IMPORTANT NOTES! WARNING:
More information2005 Dodge Grand Caravan
REMOVAL REMOVAL - REAR DISC BRAKE SHOES 1. Raise vehicle. (Refer to LUBRICATION & MAINTENANCE/HOISTING - STANDARD PROCEDURE). 2. Remove rear wheel and tire assemblies from vehicle. 3. Remove the caliper
More informationINSTALLATION INSTRUCTIONS FOR M.OR.E. SHACKLE SYSTEM (S.R.S. ) Please read terms and Policies page 5.
MOUNTAIN OFF ROAD ENTERPRISES INC. P.O. BOX 690, DELTA CO. 81416 970-625-0500 970-625-3747 fax E-mail: info@mountainoffroad.com www.mountainoffroad.com INSTALLATION INSTRUCTIONS FOR M.OR.E. SHACKLE SYSTEM
More informationInstallation Instructions
Instructions Created by an: 2005+ Toyota Tacoma BTB Front Coilovers by Low Range Off Road SKU# TAC-SP-05CO-BTB-650 Diff Drop Kit (SKU# LR-2GDDK) Instructions included Installation Instructions Revised
More informationInstallation Instructions
Instructions Created by an: DIY Alignment Toe Set Tool, 5 Patterns (SKU# DIY-TST) Installation Instructions CAUTION: Safety glasses should be worn at all times when working with vehicles and related tools
More information7929 Lincoln Ave, Riverside, CA Ph ICON Fx
7929 Lincoln Ave, Riverside, CA 92504 Ph 951.689.ICON Fx 951.689.1016 Instruction Sheet: Part No. 6-7000 7 Suspension System 2005-2007 Ford F250/F350 4WD (2) Coil Springs (1) Pan Rod Drop Bracket (2) Radius
More informationD-1-A TRIPLE VALVE, PC. NO
D-1-A TRIPLE VALVE, PC. NO. 577893 MARCH, 1985 Supersedes issue dated July, 1984 NOTE: The following description and operation is based on this device and its components being new or this device and its
More informationXJ CHEROKEE LIFT KIT
921633XN200 Thank you for choosing Rough Country for your suspension needs. 84-01 4.5 XJ CHEROKEE LIFT KIT Rough Country recommends a certified technician installs this system. In addition to these instructions,
More informationBD Adjustable Track Bar Dodge Cummins 5.9L/6.7L (4WD Models)
BD Adjustable Track Bar 2003-2012 Dodge Cummins 5.9L/6.7L (4WD Models) P/N# 1032013-F UPLEASE READ ALL INSTRUCTIONS BEFORE INSTALLATION Length adjustment of the BD Track Bar is 39-41 (bushing center to
More informationInstallation Instructions
Instructions Created by an: Suzuki Samurai Roof Rack Kit for Hard Top, Tin Top by Low Range Off Road (SKU# SEB-RRTT) Installation Instructions CAUTION: Safety glasses should be worn at all times when working
More informationKysor On/Off Rear Air Fan Drive
. Proper precautions must be taken to prevent personal injury from contact with moving parts, unintended engine start, or other hazards present when working with powered equipment. Refer to the vehicle
More informationINSTALLATION INSTRUCTION 88148
INSTALLATION INSTRUCTION 88148 Rev C For Rancho Suspension Systems RS6548, RS6549 & RS6550: GM 2500HD, 2500, and 1500HD Trucks READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION
More informationMAXXUS 22. Mechanical Sliding Disc Brake Caliper
MAXXUS 22 Mechanical Sliding Disc Brake Caliper MAXXUS 22 Mechanical Sliding Disc Brake Caliper Assembly Instructions/ Maintenance Guidelines Edition 1 This publication is not subject to any update service.
More informationMax IV Rear Axle Replacement For models after Serial Number and all rear splined axle replacements.
Max IV Rear Axle Replacement For models after Serial Number 19089 and all rear splined axle replacements. 10/8/03 Max IV Snap Ring Rear Axle replacement.doc Tools required: 9/16 Wrench 6 Extension Steel
More information88-98 GM 2-3 SUSPENSION KIT
92754500 Thank you for choosing Rough Country for your suspension needs. 88-98 GM 2-3 SUSPENSION KIT Rough Country recommends a certified technician installs this system. In addition to these instructions,
More informationInstalling RideSentry Suspension Axle Seats onto RideStar RHP Series Single-Axle and Sliding Tandem Trailer Air Suspension Systems
Issued 10-07 Technical Bulletin Installing RideSentry Suspension Axle Seats onto RideStar RHP Series Single-Axle and Sliding Tandem Trailer Air Suspension Systems Issued 1 Technical 10-07 Bulletin Hazard
More informationPRODUCT USE INFORMATION
*745N2BAG* 745N2BAG 92745000 Thank you for choosing Rough Country for your suspension needs. 05-16 TACOMA 3 Fr / 2 Rr Leveling Kit Rough Country recommends a certified technician install this system. In
More informationINSTALLATION INSTRUCTIONS 88518
INSTALLATION INSTRUCTIONS 88518 For Rancho Suspension Systems RS6518: 2009 FORD F-150 4WD READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION Rev A IMPORTANT NOTES! WARNING:
More information8" 4-LINK SUSPENSION SYSTEM. Ford Super Duty 4WD Part#:
Part#: 013813 8" 4-LINK SUSPENSION SYSTEM Ford Super Duty 4WD 2011-2016 Rev. 051817 491 W. Garfield Ave., Coldwater, MI 49036. Phone: 517-279-2135 E-mail: tech-bds@sporttruckusainc.com Read And Understand
More informationConstant Velocity Joint: Service and Repair Wheel Drive Shaft Outer Joint and Boot Replacement REMOVAL PROCEDURE
Constant Velocity Joint: Service and Repair Wheel Drive Shaft Outer Joint and Boot Replacement REMOVAL PROCEDURE Tools Required - J 8059 Snap Ring Pliers - J 35910 Seal Clamp Tool - J 41048 Small Swage
More information97-06 JEEP TJ/LJ LONG ARM UPGRADE KIT
921663U00 97-06 JEEP TJ/LJ LONG ARM UPGRADE KIT Thank you for choosing Rough Country for your suspension needs. This kit is an upgrade kit only. This kit includes frame mounting points and adjustable long
More informationPage 1 of 26 Oteco Inc. Houston, Texas
Page 1 of 26 Page 2 of 26 1.0 OVERVIEW CONTENTS 2.0 INSTALLATION GUIDELINES 2.1 Preferred Valve Orientation 2.2 Pressure Rating and Orientation of Discharge line 2.3 Reaction Forces and Anchoring of Reset
More informationInstallation Instructions
Instructions Created by an: Suzuki Sidekick / Tracker / X90 / Vitara / Grand Vitara Defiant Armor Differential Guard (SKU# KAR-DG) Installation Instructions CAUTION: Safety glasses should be worn at all
More information05-07 F250 8 SUSPENSION KIT
92159000 05-07 F250 8 SUSPENSION KIT Thank you for choosing Rough Country for your suspension needs. Rough Country recommends a certified technician installs this system. In addition to these instructions,
More informationPNEUMATIC SLIDING VALVE
INSTALLATION, OPERATION, & #: MM-SV001 6-23-09 Rev. A Page 1 of 8 PNEUMATIC SLIDING VALVE PART NUMBERS (Including, but not inclusive) SV704MSTS, SV714MSTS, SV754MSTS, SV764MSTS, SV774MSTS, SV706MSTS, SV716MSTS,
More informationFrame Bracket Side Plate Repair Procedures
Revised 02-08 Service Parts Instructions Frame Bracket Side Plate Repair Procedures Meritor RideStar RHP Series Single-Axle and Sliding Tandem Trailer Air Suspension Systems Revised 1 Service 02-08 Parts
More informationInstallation Instructions
2003-Present Toyota 4Runner 2007-2014 FJ Cruiser LRT 3" Lift Kit by Low Range Off-Road (SKU# LR-LRFJ4RU) Installation Instructions Suggested Tools: CAUTION: Safety glasses should be worn at all times when
More informationMGM Brakes Service Manual
MGM Brakes Service Manual MODEL LTR-T - 2.50 Pre 6/1/98 MODEL LTR-T - 2.50 Post 5/31/98 MODEL LTR-L3-3.00 For: Long Life Integral Release Bolt Double Diaphragm Spring Brakes Several design improvements
More informationReadyLift (Part# ) Installation Instructions
SAFETY WARNING: recommends this system be installed by a professional technician. In addition to these instructions, professional knowledge of disassembly/ reassembly procedures and post installation checks
More informationJEEP CHEROKEE (XJ) 3 SPRING KIT TM w/ Rear Add-A-Leaf & TM w/ Rear Leaf Spring
400 W. Artesia Blvd. Fax: (310) 747-3912 Compton, CA 90220 Ph: (877) 695-7812 www.trailmastersuspension.com JEEP CHEROKEE (XJ) 3 SPRING KIT 84-01 TM3730-40013 w/ Rear Add-A-Leaf & TM3730-40023 w/ Rear
More informationKysor Rear Air Fan Drives
On/Off Technology for Heavy-Duty Truck Applications Installation & Service Guide Kysor Rear Air Fan Drives thermal.borgwarner.com For Additional BorgWarner Thermal Systems Information: 800-927-7811 USA
More informationXJ CHEROKEE LIFT KIT
92169600 84-01 6.5 XJ CHEROKEE LIFT KIT Thank you for choosing Rough Country for your suspension needs. Rough Country recommends a certified technician installs this system. In addition to these instructions,
More informationInstallation Instructions
Instructions Created by an: Inchworm Tacoma Dual Case Adapter Installation Instructions Suggested Tools: CAUTION: Safety glasses should be worn at all times when working with vehicles and related tools
More informationREAD ALL INSTRUCTION THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION!
www.fabtechmotorsports.com 4331 EUCALYPTUS AVE. ~~ CHINO, CA 91710 PHONE 909-597-7800 FAX 909-597-7185 1995 1/2-2004 TOYOTA TACOMA 2 WD 4 CYLINDER KIT FTS4130-4-4 3 LIFT KIT PARTS LIST: 2 EA. ( UCA ) FT4130-4A
More informationInstallation Instructions
Instructions Created by an: 2007-Present Toyota Tundra LRT Leveling Lift Kit - 4WD by Low Range Off-Road (SKU# LR-LRTundra) Instructions also apply to 2WD Kits. Installation Instructions Revised 7-11-17
More informationInstallation Manual WJ Long Arm Upgrade kit Jeep Grand Cherokee Last Revision No.: 1/30/12 PN
Thank you for purchasing a Clayton Off Road suspension. Please check to make sure you have all necessary parts before you start your install. 4806010 WJ 99-04 Long Arm Upgrade Kit 1206100 WJ Rear 4 Link
More informationSpring Axle Owner s Manual
Spring Axle Owner s Manual Spring/Hub Axles for Marine and Utility Trailers Table of Contents Page Slipper Springs 2 Double Eye Springs 3 Inspecting Springs 4 Replacing Springs 5 Tire Tread Wear 6-7 Super
More information»Product» Safety Warning
#J1200 Installation Instructions 1987-1995 Jeep Wrangler YJ 2" Suspension Lift Read and understand all instructions and warnings prior to installation of product and operation of vehicle. Zone Offroad
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS ----3300 W. Pontiac Way Clovis, CA 93612 toll free: 1-800-445-3767 web: www.belltech.com---- 6686 REAR AXLE FLIP-KIT 2004 DODGE RAM REGULAR CAB, QUAD CAB Thank you for being selective
More informationCHEVY / GMC 1500HD / 2500HD 2WD 8 LUG 7 BASIC KIT
85101 2000-2010 CHEVY / GMC 1500HD / 2500HD 2WD 8 LUG 7 BASIC KIT C8510-4 MAIN BOX KIT W/ HARDWARE 1) FRONT X MEMBER 1) REAR X MEMBER 2) TORSION BAR DROPS 1) LEFT BUMP STOP 1) RIGHT BUMP STOP 2) SWAY BAR
More informationDisassembly / Reassembly Procedure
08-T059 Disassembly / Reassembly Procedure HEAVY DUTY TYPE PNEUMATIC CYLINDER 10A-3 SERIES Failure to observe the instructions given in this manual could cause this equipment
More information