SECTION AIR INTAKE SYSTEM
|
|
- Alvin Johnston
- 5 years ago
- Views:
Transcription
1 / AL05 SECTION AIR INTAKE Air for the engine is taken in through a grille located on the upper-rear, left-hand side of the vehicle. See Figure 1. Air passes through a chamber, reaches the air cleaner mounted near the radiator, then passes through the air cleaner and into the turbocharger of the engine. AIR CLEANER An air cleaner is used to remove dust and dirt before the air reaches the diesel engine turbocharger. It is a dry type air cleaner, and the filter element can be easily removed for cleaning or replacement through the access grille located on the rear left corner of the bus. An optional air intake restriction indicator (Filter Minder) may be installed on the engine air intake in order to inform the service personnel when the air cleaner is restricted and needs replacement. For more details on the restriction indicator, see sub-section A: AIR INTAKE RESTRICTION INDICATOR, at the end of this section. STREET SIDE AIR CLEANER MAINTENANCE MAINTENANCE INTERVALS An appropriate inspection will extend the life span of the engine and air cleaner. It is recommended that the air intake system be checked regularly. The recommended inspection interval is every time the engine oil is changed. It is not necessary to disassemble the air cleaner for inspection. The complete air intake system should be checked in the following sequence: 1. Air cleaner casing (cracks, disassembled, loose nuts or bolts) 2. Restriction indicator (loose, missing) (optional) 3. Drain valve (missing, worn-out, loose, turned the wrong way) 4. Clips on the air intake system (loose, broken) 5. Air intake system (broken or missing flanges, holes in the system). 6. Perform a stall test and refer to the Cummins engine manual for normal rpm values during the test. The engine should reach the specified values indicated in the Cummins engine manual. Replacing, repairing, or correcting any faulty situation will increase the service life of the engine and air cleaner. Figure 1 - Engine Air Intake (Typical)
2 2007AL05 2 / SHORT LIFE SPAN If the service life of the filter element is too short, check for the following: 1. Leaks in the air intake system. A leak can cause a short life span. If a restriction indicator is installed on the air intake system (see sub-section A: AIR INTAKE RESTRICTION INDICATOR, at the end of this section), also check for the following: 2. Restriction indicator improperly installed. It should be turned downwards and its lugs parallel to the airflow coming from the engine fan. It should be checked to ensure that it is neither obstructed nor turned the wrong way. 3. Wrong maintenance indicator. Use only genuine Nova Bus maintenance parts. The indicator is calibrated for the desired final pressure drop. Filter should NOT be cleaned and re-used. REPLACING AIR CLEANERS Do not replace the filter element unless the yellow ring of the restriction indicator (optional) is visible or when the obstruction has reached 22 in. H 2 O (0.8 psi) on the air restriction indicator. 1. Stop the engine. Remove the cover plate of the air cleaner. See Figure Carefully move the filter element up and down and from side to side or turn it so as to release it from the seal. See Figures 4 and Remove the filter element by making sure not to touch the casing walls. See Figure 8. Check the accuracy of the restriction indicator using a water pressure gauge or an indicator at the air intake casing of the blower assembly; the fitting may be clogged with dirt. WARNING: Carefully avoid shaking dust from the filter element. Any loose dust must be removed from the air cleaner body with a wet cloth before installing a clean element. DUST ESCAPING FROM THE AIR FILTER ELEMENT Dust escaping from the air cleaner may cause the engine to wear out rapidly. Make sure that all fittings between the air cleaner and the engine are tightened and sealed. If all fittings are tight, check for the following: 1. Make sure that the filter element seals are not damaged. 2. Check the filter element to ensure that there are no tears in the folds (holes, cracks or tears can be detected where there is evidence of dust streaks on the clean side of the element. Also, hold a light bulb inside the element; light will shine through any holes). These problems would be evidence of filter element failure, and it should be replaced. 3. If installed, check the restriction indicator to detect leaks. 4. Look for structural failure. Any damaged parts must be replaced. 4. Clean the inside surface of the casing. This will prevent dust from hindering the efficiency of the filter element. See Figures 6 and 7. Inspect the old filter element to detect any foreign matter on the sealed surface that might tamper with the efficiency of the new filter element. Apply a maximum torque of 30 lb-in. (3.4 N m) on the clamp at the filter outlet. A higher torque could damage the filter s casing. Dust going through the air filter element can often be detected by looking for streaks of dust in the air duct. COVER PLATE Figure 3 - Air Cleaner Casing
3 / AL05 INPUT SEAL OUTPUT Figure 4 - Access to Filter Element 5. Inspect the new filter element. Check the surface of the seal inside the air cleaner. It should be smooth, flat, and clean. Do not install a damaged filter element. Under no circumstance should a wet element be installed. The air intake to the engine may break or collapse a wet filter element. 6. Check the element to make sure that all piping and fittings are of the proper size and are not clogged. 7. Install the new element to evenly distribute the pressure at the bottom flange seal. See Figure Check the seal of the access cover and tighten the cover nuts. 9. If installed, reset the restriction indicator by pushing the button located on its lower part. 10. Close the access doors. Figure 5 - Direction of Rotation Figure 6 - Cleaning of Casing Figure 8 - Remove Filter YES NO YES Figure 7 - Cleaning the Casing Cover Figure 9 - Pressure Distribution
4 2007AL05 4 / BLANK PAGE
5 SECTION AIR RESTRICTION INDICATOR / AL05 DESCRIPTION See Figures A1 and A2. The purpose of this optional device is to warn when the engine air cleaner is restricted and requires replacement. The indicator is designed to prevent any engine damage that could result from a clogged air filter. When the air filter obstructs air circulation, the indicator shows a yellow ring through the transparent part of its casing. Temporary conditions such as snow or inlet screen clogging can cause a high reading. Pushing the bottom of the gauge will reset the filter gauge. If the reading is still high, (0.8 psi/22in. H 2 O) it indicates that the air cleaner should be changed. Over servicing should be avoided, because this increases the risk for gauge and seal damage. After the maintenance, described further in this section, reset the indicator. This will return the reading to zero. INSTALLATION 1. Remove the existing air cleaner gauge from the air cleaner tap. 2. Remove the air cleaner tap fitting and replace with a new fitting. - Pipe thread sealant should be used on metal fittings. Do not use sealant on the FILTER MINDER. 3. Install the FILTER MINDER gauge to the fitting. Do not over-tighten. Finger tight is sufficient. The FILTER MINDER is now ready to monitor the air cleaner system. The gauge gives a progressive indication of air filter plugging which allows the entire air filter capacity to be used. Actual filter life will vary, depending on operating conditions. STREET SIDE FILTER MINDER Figure A1 - Restriction Indicator (Filter Minder) Figure A2 - Filter Minder Installation (Typical)
6 2007AL05 6 / High restriction No restriction TROUBLESHOOTING GUIDE PROBLEM CAUSE SOLUTION a. Filter is blocked b. Air intake duct is blocked c. External vent is blocked a. Gauge is defective b. Loose clamps c. Improperly sealed filter d. Blocked fitting on gauge a. Replace filter b. Verify and clean duct c. Verify and clear vent a. Replace gauge b. Verify and tighten if necessary c. Verify and replace if damaged d. Remove and clear blockage, or replace if necessary Table 1 - Troubleshooting Guide
FBC CODES AND TRANSLATIONS TRANSLATION
FBC CODES AND TRANSLATIONS CODE TRANSLATION 500 air cleaning system checked 501 air cleaner housing found cracked 502 repaired cracked air cleaner housing 503 renewed air cleaner housing 504 air intake
More informationTC Series Cooling Systems
TC Series Cooling Systems Table of Contents Table of Contents...1 List of Figures...1 Safety...2 Introduction...2 General Specifications...2 Types of Coolant...2 Routine Maintenance...2 Surge Tank Coolant
More informationPortable Oil Free Silent Series Compressor Operating Instructions
Portable Oil Free Silent Series Compressor Operating Instructions NOTICE Carefully read this instruction manual before attempting to operate this compressor. MODEL # SERIAL # 1-800-551-2406 www.eaglecompressor.com
More informationService Access Cover. Vacuator Valve. Accessories
Under Hood Mount, Two-Stage Filtration For Large Construction & Mining Equipment The FTG Cycloflow Air Cleaner is another two-stage air cleaner with a built-in pre-cleaner. This air cleaner has axial seal
More informationCOOLING SYSTEM. Return to Main Table of Contents
COOLING SYSTEM Return to Main Table of Contents GENERAL... 2 COOLING SYSTEM... 7 RADIATOR... 9 ENGINE COOLANT PUMP... 12 THERMOSTAT... 14 ENGINE COOLANT TEMPERATURE SENDER &, SENSOR... 15 ENGINE COOLANT
More informationOPERATION AND MAINTENANCE MANUAL
WREN IBT SERIES HYDRAULIC TORQUE WRENCHES IBT SQUARE DRIVE SERIES OPERATION AND MAINTENANCE MANUAL FOR WREN Products: POINT 75, 1IBT, 3IBT, 5IBT, 8IBT, 10IBT, 20IBT, 25IBT, 35IBT, 50IBT SQUARE DRIVE HYDRAULIC
More informationOperation and Maintenance Manual http://www.torsionx.eu Use the MaxDrv Series Square Drive Torque Wrench Model.75, 1, 3, 5, 8, 10, 20, 25, 35, 50 to install and remove threaded fasteners requiring precise
More informationTURBOCHARGER Toyota Celica DESCRIPTION OPERATION TURBOCHARGING SYSTEMS All Models
TURBOCHARGER 1988 Toyota Celica 1988 TURBOCHARGING SYSTEMS All Models DESCRIPTION Most models use a water-cooled turbocharger, mounted directly to the exhaust manifold with a wastegate assembly attached
More informationIBT Series Square Drive Torque Wrenches
IBT Series Square Drive Torque Wrenches Operation and Maintenance Manual Model.75, 1, 3, 5, 8, 10, 20, 25, 35, 50 http://www.torsionx.com Use the IBT Series Square Drive Torque Wrenches Model.75, 1, 3,
More informationSERVICING INSTRUCTIONS
TSP Series 66 Triplex Plunger Pump SERVICING INSTRUCTIONS TRIPLEX TRIPLEX SERVICING PUMP PROCEDURES Valve Replacement: All inlet and discharge valves can be serviced without disrupting the inlet or discharge
More informationINTAKE AND EXHAUST GROUP CONTENTS CHARGE AIR COOLER <2.0L ENGINE> GENERAL DESCRIPTION SERVICE SPECIFICATIONS...
15-1 GROUP 15 INTAKE AND EXHAUST CONTENTS GENERAL DESCRIPTION 15-2 SERVICE SPECIFICATIONS 15-2 DIAGNOSIS 15-2 INTRODUCTION 15-2 TROUBLESHOOTING STRATEGY 15-2 SYMPTOM CHART 15-2 SYMPTOM PROCEDURES 15-3
More informationOperation and Maintenance Manual Model.75,, 3, 5, 8, 0, 0, 5, 35, 50 http://www.torsionx.com Use the MaxDrv Series Square Drive Torque Wrench Model.75,, 3, 5, 8, 0, 0, 5, 35, 50 to install and remove threaded
More informationk. Components not properly adjusted. Refer to machine technical manual for proper adjustment of components.
General Troubleshooting Charts General Troubleshooting Charts Use the charts on the following pages to help in listing all the possible causes of trouble when you begin diagnosing and testing of a machine.
More informationTroubleshooting the Transmission Hydraulic System
Testing and Adjusting IT28F INTEGRATED TOOLCARRIER POWER TRAIN Testing And Adjusting Introduction Reference: For Specifications with illustrations, refer to SENR5974, IT28F Integrated Toolcarrier Power
More informationHexPro Series Low Profile Wrenches
HexPro Series Low Profile Wrenches Operation and Maintenance Manual Model 2HP 4HP 8HP 14HP 30HP www.torquetoolsinc.com Use the HEXPRO Series Low Profile Wrenches Model 2HP 4HP 8HP 14HP 30HP to install
More informationSection 10 Chapter 17
Section 10 Chapter 17 24 Valve, 8.3 Liter Engine Air Intake System Note: All coding used in the 8.3 Liter and 9 Liter engine manuals are Cummins engine codes. These engine codes have no meaning to New
More informationTWO-STAGE HYDRAULIC PUMP. RWP55-IBT-Air
ORIGINAL INSTRUCTIONS Form No.1000458 5 SPX Corporation 5885 11th Street Rockford, IL 61109-3699 USA Tech. Services: (800) 477-8326 Fax: (800) 765-8326 Order Entry: (800) 541-1418 Fax: (800) 288-7031 Internet
More informationGENERAL SPECIFICATIONS 25-2 GENERAL. Water cooling, forced circulation with electric fan
COOLING SYSTEM GENERAL 2 COOLING SySTEM 8 RADIATOR 10 RADIATOR FAN MOTOR ASSY 12 WATER PUMP 14 THERMOSTAT 16 WATER HOSE AND PiPE 17 WATER TEMPERATURE GAUGE UNIT AND SENSOR 18 GENERAL GENERAL Y25CAOA SPECIFICATIONS
More informationTable 6-1. Problems and solutions with pump operations. No Fluid Delivery
Table 6-1. and solutions with pump operations No Fluid Delivery Fluid level in the reservoir is low. Oil intake pipe or inlet filter is plugged. Air leak in the inlet line prevents priming or causes noise
More informationENGINE COOLING GROUP CONTENTS RADIATOR GENERAL DESCRIPTION SPECIAL TOOLS THERMOSTAT
14-1 GROUP 14 CONTENTS GENERAL DESCRIPTION 14-2 SPECIAL TOOLS 14-3 DIAGNOSIS 14-3 INTRODUCTION 14-3 TROUBLESHOOTING STRATEGY 14-3 SYMPTOM CHART 14-4 SYMPTOM PROCEDURES 14-4 ON-VEHICLE SERVICE 14-17 ENGINE
More informationEngine Power Output Low
File: 3666087-t057-tr Page 1 of 5 STEP 1 Engine under excessive load STEP 2 Fuel shutoff lever (mechanical) partially engaged STEP 3 Engine will not reach full throttle STEP 4 Poor fuel quality or wrong
More informationLow Profile Wrenches Operation and Maintenance Manual
Low Profile Wrenches Operation and Maintenance Manual http://www.torquetoolsinc.com Use the HEXPRO Series Low Profile Wrenches Model 2HP 4HP 8HP 14HP 30HP to install and remove large bolts that have minimal
More informationPRESSURE CABINETS PROBLEM CAUSE SOLUTION
BLAST CABINET TROUBLESHOOTING Page 1 PRESSURE CABINETS 1. Poor Visibility. Motor rotating backwards. The motor should rotate as indicated by the arrow on the housing. If it does not rotate in the proper
More informationENGINE COOLING SYSTEM
B ENGINE A SECTION ENGINE COOLING SYSTEM CO C D CONTENTS E PRECAUTIONS... 2 Precautions for Liquid Gasket... 2 REMOVAL OF LIQUID GASKET SEALING... 2 LIQUID GASKET APPLICATION PROCEDURE... 2 PREPARATION...
More informationRUFNEX Series Low Profile Wrenches Operation and Maintenance Manual
RUFNEX Series Low Profile Wrenches Operation and Maintenance Manual http://www.torsionx.com Use the RUFNEX Series Ultra-Low Profile Wrenches to install and remove large bolts that have minimal wrench clearance.
More informationLubrication & Maintenance Schedule
REMOVE DIRT AND SPILLAGE FROM AROUND THE CRUSHER. REMOVE DUST AND DIRT FROM CRUSHER FRAME SURFACES. REMOVE DUST AND DIRT FROM DRIVE MOTOR. CHECK FLUID LEVELS IN DIESEL ENGINE (IF EQUIPPED). REFER TO ENGINE
More informationTROUBLESHOOTING FLOW CHARTS
TROUBLESHOOTING FLOW CHARTS Bowl Style Carburetor Troubleshooting Hunts and Surges Will Run only on Prime Will run only if the choke is used Determine that the governor system is functioning properly
More informationENGINE COOLING SYSTEM
B ENGINE A SECTION ENGINE COOLING SYSTEM CO C D CONTENTS E PRECAUTIONS... 2 Precautions for Supplemental Restraint System (SRS) AIR BAG and SEAT BELT PRE-TEN- SIONER... 2 Precautions for Liquid Gasket...
More informationTroubleshooting. This section outlines procedures for troubleshooting problems with the operation of the system:
Troubleshooting This section outlines procedures for troubleshooting problems with the operation of the system: 4.1 System Error Messages... 4-2 4.2 Prep Station Troubleshooting... 4-6 4.2.1 Adapter Not
More informationEPG Air Cleaners. Durable, Corrosion-Free Air Cleaner Improved Reliability, Superior Engine Protection, Easiest Serviceability
LIGHT DUST AIR CLEANERS Durable, Corrosion-Free Air Cleaner Improved Reliability, Superior Engine Protection, Easiest Serviceability The EPG air cleaner series, which incorporates Donaldson RadialSeal
More information13. FUEL SYSTEM/CARBURETOR/
13 FUEL SYSTEM/CARBURETOR/FUEL PUMP FUEL SYSTEM --------------------------------------------------------- 13-1 SCHEMATIC DRAWING ---------------------------------------------- 13-2 OPERATION OF CARBURETOR
More informationFPU SYSTEMS OPERATION MANUAL (INCLUDING REPAIR PARTS & SPECIAL TOOL LIST) BOH CONTAINERIZED LATRINES BOH FPU Field Pack-up Units
FPU SYSTEMS OPERATION MANUAL (INCLUDING REPAIR PARTS & SPECIAL TOOL LIST) BOH CONTAINERIZED LATRINES BOH FPU Field Pack-up Units CHAPTER 4 OPERATOR MAINTENANCE INSTRUCTIONS 2016 BOH Environmental LLC This
More information2003 FORESTER SERVICE MANUAL QUICK REFERENCE INDEX
2003 FORESTER SERVICE MANUAL QUICK REFERENCE INDEX ENGINE 2 SECTION FU(TURBO) EMISSION CONTROL (AUX. EMISSION CONTROL DEVICES) INTAKE (INDUCTION) EC(TURBO) IN(TURBO) This service manual has been prepared
More information12. CARBURETOR/FUEL PUMP
12 CARBURETOR/FUEL PUMP SERVICE INFORMATION... 12-2 TROUBLESHOOTING... 12-2 THROTTLE VALVE DISASSEMBLY... 12-3 THROTTLE VALVE INSTALLATION... 12-4 CARBURETOR REMOVAL... 12-5 AUTO BYSTARTER... 12-6 FLOAT
More informationStandard Valves Series Globe Valves Series Angle Valves Series Way-Valves
Installation, Operation, Maintenance Instructions Standard Valves Series 035 000 Globe Valves Series 031 000 Angle Valves Series 033 000 3-Way-Valves 1 GENERAL INFORMATION These instructions are designed
More informationJet Fans. Instruction Manual READ AND SAVE THESE INSTRUCTIONS WARRANTY
Jet Fans Instruction Manual READ AND SAVE THESE INSTRUCTIONS WARRANTY All Leader Fan products are guaranteed to be free from defects of workmanship or material and to function satisfactorily when properly
More informationCARBURETOR SERVICE INFORMATION TROUBLESHOOTING THROTTLE VALVE DISASSEMBLY THROTTLE VALVE INSTALLATION...
11 CARBURETOR SERVICE INFORMATION... 11-2 TROUBLESHOOTING... 11-2 THROTTLE VALVE DISASSEMBLY... 11-3 THROTTLE VALVE INSTALLATION... 11-4 CARBURETOR REMOVAL... 11-5 AUTO BYSTARTER... 11-6 FLOAT CHAMBER...
More informationOur older, classic EBA cowl-mounted air cleaner (shown on the right) has been replaced with our ERA Air Cleaner.
Air Cleaners Cowl-Mounted Air Cleaner Superior Protection with RadialSeal Sealing Technology Looking for a replacement to our older EBA cylindrical-shaped axial seal style air cleaner? Our RadialSeal air
More informationINTAKE AND EXHAUST GROUP CONTENTS GENERAL INFORMATION SERVICE SPECIFICATION AIR CLEANER
15-1 GROUP 15 INTAKE AND EXHAUST CONTENTS GENERAL INFORMATION 15-2 SERVICE SPECIFICATION 15-2 DIAGNOSIS 15-2 INTRODUCTION 15-2 TROUBLESHOOTING STRATEGY 15-2 SYMPTOM CHART 15-2 SYMPTOM PROCEDURES 15-3 SPECIAL
More informationENGINE COOLING Click on the applicable bookmark to selected the required model year
ENGINE COOLING - ENGINE COOLING General Information/ Service Specifications/Lubricant/Sealants GENERAL INFORMATION 0000 The cooling system is designed to keep every part of the engine at appropriate temperature
More informationLubricating Oil Pan
007-025 Lubricating Oil Pan Preparatory Steps Batteries can emit explosive gases. To reduce the possibility of personal injury, always ventilate the compartment before servicing the batteries. To reduce
More informationSYSTEM SAVER 318 AIR COMPRESSOR FOR MACK E-TECH AND ASET ENGINES MAINTENANCE MANUAL
SYSTEM SAVER 318 AIR COMPRESSOR FOR MACK E-TECH AND ASET ENGINES MAINTENANCE MANUAL NON-THROUGH DRIVE THROUGH DRIVE Service Notes About This Manual This manual provides service and repair procedures for
More informationEP1306N 5 Gallon Can Extruder System Rev. A June EP1306N Operation Manual
EP1306N Operation Manual 1 THIS PAGE HAS BEEN INTENTIONALLY LEFT BLANK 2 TABLE OF CONTENTS SECTION 1: SAFETY... 4 1. GENERAL SAFETY... 5 2. PUMP SAFETY... 5 3. FLUID PRESSURE AND COMPATIBILITY... 6 4.
More informationCooling System. Table of Contents
Sub-Headings Safety 2 s 2 Cautions 2 Notes 2 Introduction 2 General Specifications 2 Engine 2 Coolant 2 Routine Maintenance 2 Hose Connections 4 Radiator, Charge Air and Heater Cores 4 Cooling System Leaks
More informationENGINE LUBRICATION & COOLING SYSTEMS SECTIONLC CONTENTS. ENGINE LUBRICATION SYSTEM...2 Precautions...2
ENGINE LUBRICATION & COOLING SYSTEMS SECTIONLC CONTENTS ENGINE LUBRICATION SYSTEM...2 Precautions...2 LIQUID GASKET APPLICATION PROCEDURE...2 Preparation...2 SPECIAL SERVICE TOOLS...2 Lubrication Circuit...3
More informationFUEL SYSTEM. Table of Contents. Specifications. Section 3A Fuel Delivery System. Models 6/8/9.9/10/15 CARBURETOR SPECIFICATIONS
FUEL SYSTEM Section 3A Fuel Delivery System Table of Contents Specifications............................. 3A-1 WMC Carburetor Specifications............. 3A-2 WMC Carburetor Specifications.............
More informationTURBOCHARGER SYSTEM TURBOCHARGER TC 1
TURBOCHARGER SYSTEM TURBOCHARGER TC1 TC2 TURBOCHARGER SYSTEM Description DESCRIPTION Systems which increase the amount of air sent to the engine are either turbocharger type (using exhaust gas to turn
More informationTroubleshooting:Passenger Car
Troubleshooting:Passenger Car Troubleshooting If the engine or other parts has the problem, it is possible to break the exchange turbocharger again. Please confirm the notes below and inspect each part
More informationSERVICE INSTRUCTIONS,HOOVER - BAGLESS CLEANERS
SERVICE INSTRUCTIONS,HOOVER - BAGLESS CLEANERS o41oo 149 E -1 Upper Handle Handle Cap Handle Cover Rear Di_ Cup_ HEPA Front Cover pport Latch Shaft Spring Pre-Filter Rear Filter Grille Dirt Cup _,_ Front
More informationSUPERCHARGER. ON-VEHICLE INSPECTION 1. INSPECT SUPERCHARGER OIL LEVEL HINT: With the engine cold, check the oil level on the dipstick.
EG45 ONVEHICLE INSPECTION 1. INSPECT OIL LEVEL HINT: With the engine cold, check the oil level on the dipstick. (a) Park the vehicle on a level spot and turn the engine off. (b) 4WD: Remove the LH front
More information11. CARBURETOR 11-0 CARBURETOR ZX / SCOUT 50
11 CARBURETOR SERVICE INFORMATION... 11-2 TROUBLESHOOTING... 11-2 THROTTLE VALVE DISASSEMBLY... 11-3 THROTTLE VALVE INSTALLATION... 11-4 CARBURETOR REMOVAL... 11-5 AUTO BYSTARTER... 11-6 FLOAT CHAMBER...
More informationTable of Contents. 4. Before a New Turbocharger is Installed
Table of Contents 1. Turbocharger Overview ------------------------------------------------------------------ 1.1. Definition -----------------------------------------------------------------------------
More informationCIRRUS AIRPLANE MAINTENANCE MANUAL
NOISE SUPPRESSOR 1. DESCRIPTION Noise suppression is accomplished through use of a heat exchanger (Serials 0002 thru 019) or a heat exchanger and muffler (Serials 020 & subs) connected to the exhaust header
More informationP2459-DIESEL PARTICULATE FILTER REGENERATION TOO FREQUENT
2014 - DP - RAM 4500/5500 CAB CHASSIS - 6.7L I6 CUMMINS TURBO DIESEL P2459-DIESEL PARTICULATE FILTER REGENERATION TOO FREQUENT The engine aftertreatment system monitors the soot load in the Diesel Particulate
More information6 Litre Oil-Less Air Compressor
Operator s Manual 6 Litre Oil-Less Air Compressor WARNING! Before using this appliance, read the Operator s manual and follow all its safety rules and instructions. SPECIFICATION HWKAC1 1.1 kw / 1.5 HP
More informationEngine Compartment Inspection
Engine Compartment Inspection Unit Contents Student Page Student Components Learning Activities Sheet... 7 3 Abbreviated Checklist.... 7 5 Objective Sheet... 7 7 Expanded Checklist... 7 9 * Job Sheets
More information1.2.5 Installation of Cylinder Head
SERIES 50 SERVICE MANUAL 1.2.5 Installation of Cylinder Head Perform the following steps for cylinder head installation: 1. Be sure piston domes and the cylinder head and cylinder block firedeck surfaces
More informationPreventive maintenance 4
00 Series Preventive maintenance Preventive maintenance periods Use the procedures in this chapter to maintain your engine in accordance with the preventive maintenance schedule. Check the periods given
More informationSD Bendix E-12 & E-15 Dual Brake Valve DESCRIPTION
SD-03-6 Bendix E- & E-15 Dual Brake Valve TREADLE UPPER BODY ASSEMBLY PRIMARY DELIVERY ( ) 1 SECONDARY DELIVERY ( ) LOWER BODY ASSEMBLY MOUNTING PLATE PRIMARY SUPPLY ( SUP-1) PRIMARY SUPPLY ( SUP-) PRIMARY
More informationINTAKE (INDUCTION) IN(TURBO)
IN(TURBO) Page 1. General Description...2 2. Air Cleaner...7 3. Air Intake Duct...8 4. Intake Duct...9 5. Intercooler...10 6. Turbocharger...12 7. Air By-pass Valve...14 8. Resonator Chamber...15 GENERAL
More informationOWNER S TECHNICAL MANUAL
OWNER S TECHNICAL MANUAL Electronic Oil Meter 660 Description Oval gear type Hose end meter with electronic LCD display for Lubricants and Anti-Freeze fluid. The Hose end meter includes a progressive opening
More information5. FUEL SYSTEM FUEL SYSTEM 5-0
5 FUEL SYSTEM 5-0 SERVICE INFORMATION GENERAL INSTRUCTIONS SERVICE INFORMATION...5-1 CARBURETOR INSTALLATION...5-9 TROUBLESHOOTING...5-1 PILOT SCREW ADJUSTMENT...5-10 CARBURETOR REMOVAL...5-2 AUTO BYSTARTER...5-3
More informationOregon Fuel Injection
Cummins PT Fuel Pump Diagnostic No Start, with no smoke 1. This could be caused by the fuel pump not turning or a seized gear pump. Remove the fuel supply hose and the fuel inlet fitting from the gear
More informationPowers Controls TT 184 Temperature Transmitters
Powers Controls Document No. 155-077P25 TT 184-1 Room Transmitter Remote Bulb Average Bulb Rigid Bulb Description The are direct acting, one-pipe instruments that sense temperature and transmit a proportional
More informationMANUAL INSTALLATION. Venturi FX. VFX Series. v100 Issue Date: 11/22/ Price Industries Limited. All rights reserved.
MANUAL INSTALLATION Venturi FX VFX Series v100 Issue Date: 11/22/16 2016 Price Industries Limited. All rights reserved. TABLE OF CONTENTS Product Overview Safety Precautions... 1 Caution to Contractors...1
More informationTrouble Shooting Guide EWA, 3-phase (D2422)
Trouble Shooting Guide EWA, 3-phase (D2422) Trouble Shooting Guide Problem Possible Cause Possible Remedy Unit does not start Breaker tripped, no power to unit Loose wire Defective contactor or coil Close
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION NOTE: For reassembly reference, label all electrical connectors, vacuum hoses and fuel lines before removal. Also place mating marks on engine hood and other major assemblies before
More information7-6 COOLING KJ COOLING (Continued) COOLING SYSTEM DIAGNOSIS CHART - GAS ENGINE COOLING SYSTEM DIAGNOSIS CHART CONDITION POSSIBLE CAUSES CORRECTION TEM
7-6 COOLING KJ COOLING (Continued) COOLING SYSTEM DIAGNOSIS CHART - GAS ENGINE COOLING SYSTEM DIAGNOSIS CHART CONDITION POSSIBLE CAUSES CORRECTION TEMPERATURE GAUGE READS LOW 1. Has a Diagnostic Trouble
More informationMcCANNA Actuation Systems B
17710-B Ramcon Series 8/25 C/CR, 50/100 B/BR, 250/500 B/BR Electric Actuators Installation, Operation and Maintenance Instructions Contents Storage...........................................................................................................
More informationCla-Val. Service Training Manual. Simple solutions plus learning with a purpose
Cla-Val Service Training Manual Simple solutions plus learning with a purpose 5 Application Series Section General Identify What Valve You Have 5-1 Rate of Flow 40 Series 5-2 Pressure Relief 50 Series
More informationAir-Assist Service Jack Max. Capacity: 10 Tons
Form No. 565786 Parts List & Operating Instructions for: 1511B Air-Assist Service Jack Max. Capacity: 10 Tons 109 67 66 68 77 69 70 78 95 94 107 106 108 26 71 72 72 93 X L 65 75 92 91 90 89 88 87 86 85
More informationTypical Install Instructions
Typical Install Instructions Read & understand all steps of these instructions before beginning this installation. WEBER Conversion Kit, VW T-1/2, up to 1835cc 32 / 36 DFEV Weber Carburetor These instructions
More information1600 PSI ELECTRIC PRESSURE WASHER
MODEL NO.: XE03 SKU: 39-8508-6 1600 PSI ELECTRIC PRESSURE WASHER Owner s Manual QUESTIONS, PROBLEMS, MISSING PARTS? Before returning to your retailer, visit our web site or call our customer service at
More informationSECTION 4 - FUEL/LUBRICATION/COOLING
For Arctic Cat Discount Parts Call 606-678-9623 or 606-561-4983 SECTION 4 - FUEL/LUBRICATION/COOLING 4 TABLE OF CONTENTS Carburetor Specifications... 4-2 Carburetor Schematic... 4-2 Carburetor... 4-3 Cleaning
More informationOrifice Flange Union Assembly and Orifice Run Installation and Operation Manual
Orifice Flange Union Assembly and Orifice Run Installation and Operation Manual 354-EN Please read and save these instructions. Installation Procedures Orifice Flange Union Assembly Installing Orifice
More informationService Instruction ENGINE COMPONENTS, INC.
Title: Service Instruction S.I. No.: 89-5-1 Page: 1 of 5 Issued: 05/05/89 Revision: 1 (09/01/01) Technical Portions of FAA DER Approved. FAILURE OF ENGINE TO START 27 points 1. Lack of fuel 2. Ignition
More informationRoutine Compressor Maintenance
Establishing a regular, well-organized maintenance program and strictly following it is critical to maintaining the performance of a compressed air system. One person should be given the responsibility
More informationExhaust Gas Recirculation Valve, Replace J S file://c:\program Files\cosids\DATA\TMP\ rtf.html. Remove
1 Page 1 of 20 Exhaust Gas Recirculation Valve, Replace J982500 Remove 1. Disconnect battery negative lead 2. Disconnect hose (1) from oil filler on air cleaner assembly, then move to one side Release
More informationNSGV PT-1000 PORTABLE WELDING STATION I, O & M MANUAL
APPLICATION OF DUST CONTROL EQUIPMENT: CAUTION - Warning Improper operation of dust control system may contribute to conditions in the work area or facility that could result in severe personal injury
More information2004 IMPREZA SERVICE MANUAL QUICK REFERENCE INDEX
2004 IMPREZA SERVICE MANUAL QUICK REFERENCE INDEX ENGINE SECTION 1 FU(H4SO) EMISSION CONTROL (AUX. EMISSION CONTROL DEVICES) INTAKE (INDUCTION) EC(H4SO) IN(H4SO) This service manual has been prepared to
More informationSplit Body Valves with Bellows Seal Series Globe Valves Series Angle Valves Series Way-Valves
Installation, Operation, Maintenance Instructions Split Body Valves with Bellows Seal Series 025 300 Globe Valves Series 027 300 Angle Valves Series 028 300 3-Way-Valves 1 GENERAL INFORMATION These instructions
More informationADJUSTMENTS Mazda MX-3. Fig. 1: Identifying Engine Code & Number Courtesy of MAZDA MOTORS CORP. VALVE CLEARANCE ADJUSTMENT
Fig. 1: Identifying Engine Code & Number Courtesy of MAZDA MOTORS CORP. ADJUSTMENTS VALVE CLEARANCE ADJUSTMENT 1. No valve clearance adjustment is required, as hydraulic valve lash adjusters are used.
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Universal Air Series!! NOTE!! Covers the following model: 6000 Series 85-0100B-AZ Rev 0 5/07 To ensure that the system is installed properly, provide your electrician with these
More informationService Information System
Page 1 of 7 7HVWLQJDQG$GMXVWLQJ &&DQG&2QKLJKZD\(QJLQHV 0HGLD1XPEHU5(15 3XEOLFDWLRQ'DWH 'DWH8SGDWHG Aftercooler - Test SMCS - 1063-081 Table 1 Tools Needed Part Number Part Name Quantity 1U-5470 Engine
More informationFUEL SYSTEM/CARBURETOR/FUEL PUMP
13 FUEL SYSTEM/CARBURETOR/FUEL PUMP FUEL SYSTEM-------------------------------------------------------------------------------------13-1 SCHEMATIC DRAWING-------------------------------------------------------------------------13-2
More informationWARNING. Filter Service. Section Refer to the following pages for timing and procedures of fi lter element replacement.
Section 10-1 Filter Service Effective fi ltration of fl uids is vital to the longevity and performance of your Wagner. See the previous section on Preventive Maintenance for the scheduled intervals for
More informationUNPACKING SAFETY GUIDELINES GENERAL SAFETY INFORMATION. Operating Instructions & Maintenance Manual
Please read and save this Repair Parts Manual. Read this manual and the General Operating Instructions carefully before attempting to assemble, install, operate or maintain the product described. Protect
More informationINTAKE/EXHAUST SYSTEM 7 C TURBOCHARGER
INTAKE/EXHAUST SYSTEM 7 C TURBOCHARGER Table Of Contents Page Identification.................................. 7C-1 Torque Specifications.......................... 7C-1 Sealants.....................................
More informationOreck Magnesium Series Service Manual. The Oreck Manufacturing Company
Oreck Magnesium Series Service Manual The Oreck Manufacturing Company 08/2012 10/2011 The Oreck Manufacturing Company Contents Covering all Magnesium Upright Models Including: LW100, LW125, LW1000, AND
More informationAir Operated Grease Ratio Pumps 50:1 BGRP
INSTRUCTION MANUAL S1350, Rev C Air Operated Grease Ratio Pumps 50:1 BGRP Congratulations on purchase of this World Class Air Operated Grease Ratio Pump! World-class Industrial High Pressure Grease pump
More informationSECTION 4 PERIODIC INSPECTIONS NOTE
LYCOMING OPERATOR S MANUAL SECTION 4 O-360 AND ASSOCIATED MODELS PERIODIC INSPECTIONS SECTION 4 PERIODIC INSPECTIONS NOTE Perhaps no other factor is quite so important to safety and durability of the aircraft
More informationINSTALLATION, OPERATION AND MAINTENANCE MANUAL WALL EXHAUST FANS BELT DRIVE XBL FANS
INSTALLATION, OPERATION AND MAINTENANCE MANUAL WALL EXHAUST FANS BELT DRIVE XBL FANS The purpose of this manual is to aid in the proper installation and operation of the fans. These instructions are intended
More informationREMAN MBE 4000 Turbo Brake Assembly
TO: Service Locations No.: 06 TS - 22 August 17, 2006 FROM: SUBJECT: Technical Support REMAN MBE 4000 Turbo Brake Assembly ISSUE A new service assembly (P/N: R4571401206) is now available to install a
More informationINSTALLATION & MAINTENANCE MODEL mm
MODEL 65-25mm INSTALLATION INSTRUCTIONS CAUTION: Installation of Backflow Preventers must be performed by qualified, licensed personnel. The installer should be sure the proper device has been selected
More informationRocker Lever Assembly
003-009 Rocker Lever Assembly Preparatory Steps Remove the air piping from the intake manifold. Remove the rocker lever cover. Refer to Procedure 003-011 in Section 3. Remove the engine brakes, if equipped.
More informationGeneral Information. Note : The aftertreatment DOC is integrated into the inlet of the exhaust aftertreatment system. WARNING
General Information The material captured in a diesel particulate filter may contain elevated concentrations of media, primarily zinc and molybdenum, and possibly polynuclear aromatic hydrocarbons that
More informationSection 10 Chapter 7
Section 10 Chapter 7 24 Valve, 8.3 Liter Engine Troubleshooting Symptoms Identification Note: All coding used in the 8.3 Liter and 9 Liter engine manuals are Cummins engine codes. These engine codes have
More informationSRT OPERATIONS MANUAL
MAINTENANCE SECTION PAGE # VEHICLE DAILY INSPECTION.......................................1 P.M. INSPECTION #1.................................................3 P.M. INSPECTION #2.................................................6
More informationREAD AND SAVE THESE INSTRUCTIONS. Air Boss MP600M Vertical Air Flow Mist Precipitator Industrial Applications. TRION
READ AND SAVE THESE INSTRUCTIONS Vertical Air Flow Mist Precipitator Industrial Applications TRION Vertical Air Flow Mist Precipitator for Industrial Applications Table of Contents Design...2 Installation...2
More information12. CARBURETOR 12-0 CARBURETOR VITALITY 50
12 12 CARBURETOR SERVICE INFORMATION (2-STROKE)... 12-2 SERVICE INFORMATION (4-STROKE)... 12-3 THROTTLE VALVE (2-STROKE)... 12-5 CARBURETOR (2-STROKE)... 12-7 AIR SCREW ADJUSTMENT (2-STROKE)... 12-13 REED
More information