File: 12-fc131 Page 1 of 11. Fault Code 131 CODES REASON EFFECT
|
|
- Judith Harrell
- 6 years ago
- Views:
Transcription
1 File: 12-fc131 Page 1 of 11 Fault Code 131 Accelerator Pedal or Lever Position Sensor Circuit - Voltage Above Normal, or Shorted to High Source CODES REASON EFFECT Fault Code: 131 PID(P), SID(S): P091 FMI: 3/3 Lamp: Red SRT: Accelerator Pedal or Lever Position Sensor Circuit - Voltage Above Normal, or Shorted to High Source. High voltage detected at accelerator pedal or lever position circuit. Severe derate in power output of the engine. Limp home power only. Accelerator Pedal or Lever Position Sensor Circuit Circuit Description: The accelerator pedal or lever position sensor is attached to the accelerator pedal or lever. The accelerator pedal or lever position sensor sends a signal to the electronic control module (ECM) when the accelerator pedal or lever is depressed and released. The accelerator pedal or lever position circuit contains three wires: accelerator pedal or lever Position +5 Volt Supply, accelerator pedal or lever Position Return, and accelerator pedal or lever Position Signal. Component Location: The accelerator pedal or lever position sensor is located on the accelerator pedal or lever. Refer to the OEM manual. Shop Talk: If troubleshooting an intermittent accelerator problem: The accelerator pedal or lever position sensor signal voltage can be monitored with the INSITE electronic service tool, while flexing the harness to locate the intermittent connection. Possible causes of this fault include: accelerator pedal or lever position signal circuit shorted to battery or +5 volt supply Open accelerator pedal or lever return circuit in the harness or connections Accelerator supply shorted to battery Failed accelerator pedal or lever position sensor.
2 File: 12-fc131 Page 2 of 11 Note: The three wires in the accelerator position sensor circuit must be twisted together.
3 File: 12-fc131 Page 3 of 11 TROUBLESHOOTING SUMMARY CAUTION To reduce the possibility of damaging a new ECM, all other active fault codes must be investigated prior to replacing the ECM. CAUTION To reduce the possibility of pin and harness damage, use the following test leads when taking a measurement: Part Number female Weather-Pack test lead Part Number male Deutsch/AMP/Metri-Pack test lead. STEPS SPECIFICATIONS SRT CODE STEP 1: Check the fault codes. STEP 1A: Check for sensor supply fault codes. Fault Code 387 active? STEP 1B: Check for an active fault code. Fault Code 131 active? STEP 2: STEP 2A: STEP 2B: Check the accelerator pedal or lever position sensor circuit. Inspect the accelerator pedal or lever position sensor and connector pins. Check the accelerator pedal or lever position sensor supply voltage and return circuit to 5.25 VDC? STEP 2C: Check the circuit response. Fault Code 132 active and Fault Code 131 inactive? STEP 2D: STEP 3: STEP 3A: STEP 3A-1: STEP 3A-2: Check the fault codes and verify accelerator pedal or lever condition. Check the ECM and OEM harness. Inspect ECM and OEM harness connector pins. Check for an open circuit in the OEM harness. Check for a pin-to-pin short circuit in the OEM harness. Fault Code 132 is active? Less than 10 ohms? Greater than 100k ohms? STEP 3B: Check for an inactive fault code. Fault Code 131 inactive? STEP 4: Clear the fault codes. STEP : Disable the fault code. Fault Code 131 inactive? STEP 4B: Clear the inactive fault codes. All fault codes cleared?
4 File: 12-fc131 Page 4 of 11 STEP 1: STEP 1A: Check the fault codes. Check for sensor supply fault codes. TROUBLESHOOTING STEP check for sensor supply fault codes. Using INSITE, read the fault codes. Fault Code 387 active? Fault Code 387 active? Fault Code 387 1B STEP 1B: Check for an active fault code. check for an active fault code. Using INSITE, read the fault codes. Fault Code 131 active? Fault Code 131 active? 2A Inactive or Intermittent Fault Code, Procedure
5 File: 12-fc131 Page 5 of 11 STEP 2: STEP 2A: Check the accelerator pedal or lever position sensor and circuit. Inspect the accelerator pedal or lever position sensor and connector pins. Disconnect the accelerator pedal or lever position sensor from the OEM harness. inspect the oem harness and sensor connector pins for the following: Loose connector Corroded pins Bent or broken pins Pushed back or expanded pins Moisture in or on the connector Missing or damaged connector seals Dirt or debris in or on the connector pins Wire insulation damage Connector shell broken. For general inspection techniques, refer to Component Connector and Pin Inspection, Procedure A defective connection has been detected in the sensor or harness connector. Clean the connector and pins. Repair the damaged harness, connector, or pins if possible. Refer to Procedure B
6 File: 12-fc131 Page 6 of 11 STEP 2B: Check the accelerator pedal or lever position sensor supply voltage and return circuit. Disconnect the accelerator pedal or lever position sensor from the OEM harness. measure the voltage from the accelerator pedal position sensor +5 volt supply pin to the accelerator pedal position sensor return pin at the sensor connector of the oem harness. Refer to the wiring diagram for connector pin identification to 5.25 VDC? 4.75 to 5.25 VDC? 2C 3A STEP 2C: Check the circuit response. Disconnect the accelerator pedal or lever position sensor from the OEM harness. check for the appropriate ecm response after 30 seconds. Read the fault codes using INSITE. Fault Code 132 active and Fault Code 131 inactive? Fault Code 132 active and Fault Code 131 inactive? 2D 3A
7 File: 12-fc131 Page 7 of 11 STEP 2D: Check the fault codes and verify accelerator pedal or lever condition. Connect the accelerator pedal or lever to the OEM harness. check for the appropriate circuit response after 30 seconds. Using INSITE, read the fault codes. Fault Code 132 is active? A defective accelerator pedal or lever has been detected. Contact the appropriate OEM or dealership for repair instructions. Replace the accelerator pedal or lever. Refer to the OEM troubleshooting manual. Fault Code 132 is active? None. The removal and installation of the connector corrected the failure. STEP 3: STEP 3A: Check the ECM and OEM harness. Inspect the ECM and OEM harness connector pins. Disconnect the OEM harness from the ECM. inspect the oem harness and ecm connector pins for the following: Loose connector Corroded pins Bent or broken pins Pushed back or expanded pins Moisture in or on the connector Missing or damaged connector seals Dirt or debris in or on the connector pins Wire insulation damage Connector shell broken. For general inspection techniques, refer to Component Connector and Pin Inspection, Procedure A defective connection has been detected in the harness connector. Clean the connector and pins. Repair the damaged harness, connector, or pins if possible. Refer to Procedure A-1
8 File: 12-fc131 Page 8 of 11 STEP 3A-1: Check for an open circuit in the OEM harness. Disconnect the OEM harness from the ECM. Disconnect the accelerator pedal or lever position sensor from the OEM harness. check for an open circuit. Measure the resistance between the OEM harness ECM connector accelerator pedal or lever RETURN pin and the OEM harness accelerator pedal or lever RETURN pin. Refer to the wiring diagram for connector pin identification. For general resistance measurement techniques, refer to the Resistance Measurements Using a Multimeter and Wiring Diagram, Procedure Less than 10 ohms? Less than 10 ohms? An open RETURN circuit has been detected in the OEM harness. Repair or replace the OEM harness. Refer to Procedure A-2
9 File: 12-fc131 Page 9 of 11 STEP 3A-2: Check for a pin-to-pin short circuit in the OEM harness. Disconnect the OEM harness from the ECM. Disconnect the accelerator pedal or lever position sensor from the OEM harness. check for a pin to pin short. Measure the resistance between the accelerator pedal or lever SIGNAL pin in the OEM harness ECM connector and all other pins in the OEM connector. Refer to the wiring diagram for connector pin identification. For general resistance measurement techniques, refer to the Resistance Measurements Using a Multimeter and Wiring Diagram, Procedure Greater than 100k ohms? Greater than 100k ohms? Repair or replace the OEM harness. Refer to Procedure B
10 File: 12-fc131 Page 10 of 11 STEP 3B: Check for an inactive fault code. Connect all components. check for the appropriate circuit response after 30 seconds. Using INSITE, read the fault codes. Fault Code 131 inactive? None. The removal and installation of the connector corrected the failure. Fault Code 131 inactive? Call for pre-authorization. Replace the ECM. Refer to Procedure STEP 4: STEP : Clear the fault codes. Disable the fault code. Connect all components. disable the fault code. Start the engine and let it idle for one minute. Using INSITE, verify that the fault code is inactive. Fault Code 131 inactive? Fault Code 131 inactive? 4B 1A STEP 4B: Clear the inactive fault codes. Connect all components. clear the inactive fault codes. Erase the inactive fault codes using INSITE. All fault codes cleared? All fault codes cleared? Repair complete Appropriate troubleshooti ng steps
11 File: 12-fc131 Page 11 of 11
TROUBLESHOOTING SUMMARY. STEPS SPECIFICATIONS SRT CODE STEP 1: Check the fault codes.
File: 16-t05-195-2wire Page 1 of 10 TROUBLESHOOTING SUMMARY CAUTION To reduce the possibility of damaging a new ECM, all other active fault codes must be investigated prior to replacing the ECM. CAUTION
More informationFAULT CODE 692 Turbocharger Number 1 Compressor Inlet Temperature Sensor Circuit - Voltage Below Normal or Shorted to Low Source
Page 1 of 14 FAULT CODE Turbocharger Number 1 Compressor Inlet Temperature Sensor Circuit - Voltage Below Normal or Shorted to Low Source View Related Topic Overview CODE REASON EFFECT : PID: SPN: 1172
More informationFAULT CODE 451 Injector Metering Rail Number 1 Pressure Sensor Circuit - Voltage Above Normal or Shorted to High Source
Page 1 of 16 FAULT CODE 451 Injector Metering Rail Number 1 Pressure Sensor Circuit - Voltage Above Normal or Shorted to High Source View Related Topic Overview CODE REASON EFFECT Fault Code: 451 PID:
More informationCUMMINS FAULT CODE: 1239 PID: SPN: 2623 FMI: 3/3 LAMP: AMBER
CUMMINS ACCELERATOR PEDAL OR LEVER POSITION SENSOR 2 CIRCUIT - VOLTAGE ABOVE NORMAL OR HORTED TO HIGH SOURCE FAULT CODE: 1239 PID: SPN: 2623 FMI: 3/3 LAMP: AMBER DESCRIPTION ISX and ISM Accelerator Pedal
More informationFAULT CODE 131 (IVS) Accelerator Position Sensor Circuit
FAULT CODE 131 (IVS) Accelerator Position Sensor Circuit Overview CODE REASON EFFECT Fault Code: 131 PID: P091 SPN: 91 FMI: 3 LAMP: Red SRT: 00-084 High voltage detected at accelerator position signal
More informationFAULT CODE 132 (SSS) Accelerator Position Sensor Circuit
FAULT CODE 132 (SSS) Accelerator Position Sensor Circuit Overview CODE REASON EFFECT Fault Code: 132 PID: P091 SPN: 91 FMI: 4 LAMP: Red SRT: 00-084 Low voltage detected at the accelerator position signal
More informationAssociated Procedures. Troubleshooting Steps SPECIFICATIONS. Check for multiple fault codes. STEP 1. Fault Code 283 or 284 inactive
Associated Procedures Troubleshooting Steps STEPS SPECIFICATIONS STEP 1. Check for multiple fault codes. STEP 1A. Read faults. Fault Code 283 or 284 inactive STEP 2. Check the engine harness. STEP 2A.
More informationFAULT CODE 474. Starter Solenoid Lockout Relay Driver Circuit
Page 1 of 12 Overview FAULT CODE 474 Starter Solenoid Lockout Relay Driver Circuit CODE REASON EFFECT Fault Code: 474 PID: S052 SPN: 1321 FMI: 2 LAMP: Yellow SRT: Either low voltage detected when 12 VDC
More informationFAULT CODE 432 (SSS) Accelerator Pedal Circuit
FAULT CODE 432 (SSS) Accelerator Pedal Circuit Overview CODE REASON EFFECT Fault Code: 432 PID: P091 SPN: 91 FMI: 13 LAMP: Red SRT: 00-612 No voltage detected at idle validation on-idle signal pin 6 of
More informationAccelerator Pedal or Lever Position Sensor Circuit
Page 1 of 9 019-086 Accelerator Pedal or Lever Position Sensor Circuit Initial Check CAUTION Do not use probes or leads other than Part No. 3822758. The OEM connector will be damaged. The leads must fit
More informationEngine Performance Troubleshooting Tree - Signature and ISX CM870
File: 70-t02-1001 Page 1 of 64 Engine Performance Troubleshooting Tree - Signature and ISX CM870 This troubleshooting procedure should be followed for the following symptoms: Engine Acceleration or Response
More informationISC, QSC8.3, and ISL (FIS )
Fault Information System... 1 FIS Usage Recommendations... 2 FIS Usage Recommendations... 2 Diagnostic Methods... 9 Troubleshooting Fault Codes... 9 Information Fault Codes... 3 (fc211) Fault Code 211...
More informationFAULT CODE 482. Fuel Pressure Low - Data Valid but Below. Operational Range - Moderately Severe Level.
Fuel Pressure Low - Data Valid but Below Normal Operational Range - Moderately Seve... Page 1 of 19 FAULT CODE 482 Fuel Pressure Low - Data Valid but Below Normal Operational Range - Moderately Severe
More informationFAULT CODE SAE J1939 Multiplexing PGN Timeout Error - Abnormal Update Rate
File: 00-t05-285 Page 1 of 7 FAULT CODE 285 - SAE J1939 Multiplexing PGN Timeout Error - Abnormal Update Rate Associated Procedures Procedure Title Procedure Number Service Model Name Bulletin Number Engine
More informationAdditions, Revisions, or Updates
1 8 02-14 SUBJECT DATE SPN 4334 (ACM) (GHG14) August 2014 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change SPN 4334/FMI 3 - DDC-SVC-MAN-0084 GHG14 DD Platform GHG14
More informationCAUTION Fuel Lift Pump. Initial Check. Resistance Check. https://qsol2.cummins.com/qs2/pubsys2/xml/en/procedures/10/
Page 1 of 16 View Related Topic 005-045 Fuel Lift Pump Initial Check Inspect the engine harness, the lift pump power connector, the lift pump relay power connector and the lift pump relay pins for the
More informationAdditions, Revisions, or Updates
1 01 06-16 SUBJECT SPN 4334/FMI 4 (ACM) (GHG14) SPN 4334/FMI 4 (ACM) (GHG17) DATE January 2016 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0084
More informationAdditions, Revisions, or Updates
1 4 09-14 SUBJECT DATE ACM2.1 SPN 3597/FMI 3, 4 - GHG14 April 2014 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0084 DD Platform SPN 3597/FMI 3,
More informationAdditions, Revisions, or Updates
1 8 09-14 SUBJECT DATE SPN 3361 (ACM) (GHG14) August 2014 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0084 DD Platform SPN 3361/FMI 3, 4, 5, 31
More informationGeneral Information. Resistance Check
General Information The CELECT system can control the fan clutch activation. The ECM energizes the fan clutch or air valve solenoid. Refer to vehicle manufacturer's publications for more information on
More informationAdditions, Revisions, or Updates
1 01 11-16 SUBJECT DATE SPN 647 (MCM)(EPA07-EPA10-GHG14) January 2016 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0084 DDC-SVC-MAN-S084 DD Platform
More informationAdditions, Revisions, or Updates
1 01 29-14 SUBJECT DATE SPN 3511/FMI 3 and 4 - GHG14 January 2014 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change SPN 3511/FMI 3 - DDC-SVC-MAN-0084 GHG14 DD Platform
More informationAdditions, Revisions, or Updates
1 10 16-13 SUBJECT DATE SPN 3216/FMI 13 - EPA10/GHG14 October 2013 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0084 EPA10 GHG14 DD Platform SPN
More informationSureShift Transmission
Issued 10-99 $2.50 SureShift Transmission Maintenance and Diagnostics Manual No. MM-9970 WE SUPPORT VOLUNTARY TECHNICIAN CERTIFICATION THROUGH TM Service Notes Service This Notes publication provides maintenance
More informationThrottle Position Sensor Circuit - Test
Throttle Position Sensor Circuit - Test System Operation Description: The throttle position sensor is mounted to a pedal assembly. The throttle position sensor provides a signal to the Electronic Control
More information2012 Volkswagen Eos Komfort
Test-ID Specified value min. max. 1 Rich to lean sensor barrier - 0.6241 V voltage 2 Lean to rich sensor barrier - 0.6241 V voltage 7 Minimum voltage at sensor - 0.450 V for test cycle 8 Maximum voltage
More informationDTC P2100, P2103 THROTTLE CONTROL MOTOR RELAY
DTC P2100, P2103 THROTTLE CONTROL MOTOR RELAY Component Description INFOID:0000000001702985 Power supply for the throttle control motor is provided to the ECM via throttle control motor relay. The throttle
More informationP TURBOCHARGER BOOST CONTROL CIRCUIT/OPEN
Page 1 of 8 P0045 - TURBOCHARGER BOOST CONTROL CIRCUIT/OPEN Page 2 of 8 Page 3 of 8 For a complete wiring diagram Refer to Section 8W When Monitored: With the ignition on and the Boost Pressure Servo Motor
More informationAdditions, Revisions, or Updates
1 29-13 1 1 29-13 SUBJECT DATE DD Platform GHG 14 SPN 3361 FMI 3, 4, 5 UPDATE January 2013 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0084 GHG
More informationSPN 1176/FMI 3 SPN 1176/FMI 4
NUMBER: 8 01 13 S.M. REF.: Listed in Table ENGINE: EPA07 MBE 900 DATE: August 2013 SUBJECT: SPN 1176/FMI 3, 4 ADDITIONS, REVISIONS, OR UPDATES Publication Number Platform Section Title Change DDC-SVC-MAN-0015
More informationVolkswagen > New Beetle, New Beetle Convertible > Liter 4-Cyl. 2V Generic Scan Tool, Engine Code(s): AEG 24 - Components, Checking
Page 1 of 9 Volkswagen > New Beetle, New Beetle Convertible > 1998-2008 2.0 Liter 4-Cyl. 2V Generic Scan Tool, Engine Code(s): AEG 24 - Components, Checking. Throttle Valve Control Module J338, Checking
More informationDTC P Shift Solenoid Circuit Electrical
1998 Pontiac Grand Prix DTC P0753 1-2 Shift Solenoid Circuit Electrical Circuit Description The 1-2 Shift Solenoid Valve (1-2 SS Valve) controls the fluid flow acting on the 1-2 and 3-4 shift valve. The
More information1 of 8 9/11/2015 3:59 PM
1 of 8 9/11/2015 3:59 PM P013C-O2 SENSOR 2/2 SLOW RESPONSE - RICH TO LEAN For complete wiring diagrams refer to Diagrams/Electrical. - When Monitored: With the engine running, vehicle speed between 32
More informationP O2 SENSOR 1/1 HEATER CIRCUIT
Page 1 of 8 P0030 - O2 SENSOR 1/1 HEATER CIRCUIT Page 2 of 8 For a complete wiring diagram Refer to Section 8W Page 3 of 8 When Monitored: With the ignition on and the Oxygen Sensor Heater command on.
More informationThe engine control module (ECM) uses the following information to calculate an expected airflow rate.
DTC Descriptors DTC Mass Air Flow (MAF) sensor performance Circuit/System Description The engine control module (ECM) uses the following information to calculate an expected airflow rate. The throttle
More informationAdditions, Revisions, or Updates
1 10 28-13 SUBJECT DATE SPN 625/FMI 9 EPA10 - GHG14 (ACM) October 2013 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0084 EPA10/ GHG14 DD Platform
More informationFault Code 34 - Weak Battery Voltage Supply
Fault Code 34 - Weak Battery Voltage Supply Fault Isolation Procedures TRTS0930 Fault Code 34 - Weak Battery Voltage Supply J1587: MID 130 PID 168 FMI 14 J1939: SA 3 SPN 168 FMI 14 Overview This fault
More informationD2 - RAM 3500 PICKUP - 6.7L CUMMINS TURBO DIESEL
0 - D - RAM 00 PICKUP -.7L CUMMINS TURBO DIESEL PB-O SENSOR / CELL CIRCUIT OPEN BATT A0 B(+) ELECTRONICS TOTALLY INTEGRATED POWER FUSED IGNITION SWITCH OUTPUT (RUN-START) PORT LOW PORT HIGH POWER 7 C 7
More informationAdditions, Revisions, or Updates
1 03 12-17 SUBJECT DATE SPN 157 (MCM) GHG17 March 2017 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0193 DD Platform - Med Duty SPN 157/FMI 16 -
More informationRev Rev. Additions, Revisions, or Updates
1 4 89-12Rev SUBJECT DATE SPN 5927/FMI 2 and 7 - GHG14 April 2012 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change SPN 5927/FMI 2 - DDC-SVC-MAN-0084 DD Platform
More informationDTC P0131 HO2S CIRCUIT LOW VOLTAGE (BANK 1/SENSOR 1)
2008 Kia Sorento 3.3L Eng LX DTC P0131 HO2S CIRCUIT LOW VOLTAGE (BANK 1/SENSOR 1) COMPONENT LOCATION Fig 1: Identifying HO2S GENERAL DESCRIPTION In order to control emissions of the CO, HC and x components
More informationTroubleshooting flowcharts CONTACT US 1-877-838-1399 support@rmstator.com Local & International: 819-849-7333 www.rmstator.com MELTED CONNECTORS CIRCLE OF DEATH Mispositioned connectors create irregular
More informationDTC P Shift Solenoid Circuit Electrical
1998 Pontiac Grand Prix DTC P0753 1-2 Shift Solenoid Circuit Electrical Circuit Description The 1-2 Shift Solenoid Valve Assembly (1-2 SS Valve Assy.) controls the transmission fluid pressure on the 1-2
More informationSB Issue date: July 18, 2012
SB-08-162 Issue date: July 18, 2012 Bendix TABS-6 TroubleShooting Guide Bendix has developed the attached TroubleShooting Guide to provide an easy to follow method of isolating and correcting problems
More informationP0365-CAMSHAFT POSITION SENSOR CIRCUIT - BANK 1 SENSOR 2
3 - JC - DODGE JOURNEY - 2.4L 4 CYL DOHC 6V DUAL V.V.T. P0365-CAMSHAFT POSITION CIRCUIT - BANK 2 MODULE- CMP /2 CMP / CKP CKP CMP / CMP /2 POWERTRAIN 85 C2 22 C 67 C2 87 C2 62 C2 66 C2 88 C2 86 C2 67 C2
More informationGROUP 35A 35A-1 CONTENTS GENERAL DESCRIPTION... 35A-3 BASIC BRAKE SYSTEM DIAGNOSIS 35A-6 HYDRAULIC BRAKE BOOSTER (HBB) DIAGNOSIS...
35A-1 GROUP 35A CONTENTS GENERAL DESCRIPTION......... 35A-3 DIAGNOSIS 35A-6 INTRODUCTION..................... 35A-6 DIAGNOSTIC TROUBLESHOOTING STRATEGY......................... 35A-6 SYMPTOM CHART...................
More informationMK - JEEP COMPASS/PATRIOT - 2.4L 4 CYL DOHC 16V DUAL V.V.T.
9 - MK - JEEP COMPASS/PATRIOT -.4L 4 CYL DOHC 6V DUAL V.V.T. C6-ABS PUMP MOTOR SUPPLY LOW VOLTAGE BATT A A (TIPM) FUSE 5 7 C TIPM A9 RD/DB FUSED B(+) (PUMP) ANTI-LOCK GROUND 6 47 GROUND Z99 BK/WT Z99 BK/WT
More informationENGINE AND EMISSION CONTROL
17-1 GROUP 17 ENGINE AND EMISSION CONTROL CONTENTS ENGINE CONTROL.......... 17-3 GENERAL DESCRIPTION...... 17-3 ENGINE CONTROL SYSTEM DIAGNOSIS.................. 17-3 INTRODUCTION TO ENGINE CONTROL SYSTEM
More informationRWRG Main Shaft Speed Sensor Pre-Authorization
RWRG0076 - Main Shaft Speed Sensor Pre-Authorization Overview The UltraShift PLUS and Fuller Advantage transmissions are equipped with four electronic speed sensors. The Input Shaft, Main Shaft and Output
More informationP245C REQUESTED INFORMATION P245C EGR COOLER BYPASS CONTROL CIRCUIT LOW RAM Pickup 6.7L Eng /12/2014 Printer Friendly View
P245C 2012 RAM Pickup 6.7L Eng 2500 REQUESTED INFORMATION P245C EGR COOLER BYPASS CONTROL CIRCUIT LOW http://www1.prodemand.com/print/index?content=tabs&module=true&tab=true&terms=true&ymms=false&classname=
More informationAdditions, Revisions, or Updates
1 3 30-12 SUBJECT DATE SPN 1761/FMI 2, 9 - MY13 March 2012 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0084 MY13 DD Platform SPN 1761/FMI 2 - MY13
More informationP0222-THROTTLE POSITION SENSOR 2 CIRCUIT LOW
- RT - DODGE CARAVAN -.L V V.V.T. P- POSITION SENSOR CIRCUIT LOW 5 VOLT SUPPLY CONTROL 5 VOLT SUPPLY 5 VOLT SUPPLY APPS SENSOR APPS APPS SENSOR APPS SENSOR- ACCELERATOR PEDAL POSITION 9 C 5 K855 K85 K7
More informationSPN 723/FMI 3, 8, 10, 11, 31 - All Years February SPN 723/FMI 3 - All Years. SPN 723/FMI 8 - All Years. SPN 723/FMI 10 - All Years
1 49-13 1 1 49-13 SUBJECT DATE SPN 723/FMI 3, 8, 10, 11, 31 - All Years February 2013 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change SPN 723/FMI 3 - All Years
More informationP0406-EGR POSITION SENSOR CIRCUIT HIGH
- LX - DODGE MAGNUM/CHARGER -.5L V V MPI - HIGH OUTPUT P-EGR POSITION SENSOR CIRCUIT HIGH F85 Z9 ASSEMBLY- EXHAUST GAS RECIRCULATION (EXCEPT SRT8) S S5.7L/.5L 5.7L F85.7L.5L C Z9 Z9 Z9 F85 K9 DB/DG S S
More information1 of 14 9/4/2016 4:05 PM
1 of 14 9/4/2016 4:05 PM P0068-MANIFOLD PRESSURE/THROTTLE POSITION CORRELATION P0068-Manifold Pressure/Throttle Position Correlation Theory of Operation This DTC sets when an unexpected high intake manifold
More information9-2 FAULT CODE DIAGNOSTICS AND REPAIR PROCEDURES
SERVICE BULLETIN (Not applicable to Mack Trucks Australia) (Supersedes bulletin SB-221-032 dated 3/20/03) NUMBER: SB-221-032 DATE: 12/4/03 MODEL: All 9-2 FAULT CODE DIAGNOSTICS AND REPAIR PROCEDURES A
More informationhttps://qsol2.cummins.com/qs2/pubsys2/xml/en/outlines/ html
(4022250) ISX15 CM2250 Service Manual https://qsol2.cummins.com/qs2/pubsys2/xml/en/outlines/4022250.html Page 1 of 1 (4022250) ISX15 CM2250 Service Manual Search Manual Search Help With Printing Front
More informationDTC P0324, P0325, P0326, P0327, P0328, P0330, P0332, or P0333
DTC Descriptor DTC P0324 Knock sensor module performance DTC P0325 Knock sensor circuit bank one DTC P0326 Knock sensor performance DTC P0327 Knock sensor circuit low voltage bank 1 DTC P0328 Knock sensor
More informationP0073-AMBIENT AIR TEMPERATURE SENSOR CIRCUIT HIGH
8 - JK - JEEP WRANGLER -.8L V6 (SMPI) P7- SENSOR CIRCUIT HIGH BATT A AAT RETURN AAT SIGNAL B(+) BUS (+) BUS (-) ELECTRONICS POWER 4 C4 5 C4 6 C 5 C S S G9 8 VT/BR G 8 VT/LG C 4 C BUS (+) 5 C BUS (-) POWERTRAIN
More information5 Volt Engine Pressure Sensor Supply Circuit - Test
Page 1 of 9 Shutdown SIS Previous Screen Product: TRUCK ENGINE Model: C-15 TRUCK ENGINE 6NZ Configuration: C-15 Truck Engine 6NZ00001-UP Troubleshooting 3406E, C-10, C-12, C-15, C-16 and C-18 On-highway
More informationBASIC BRAKE SYSTEM GROUP 35A 35A-1 CONTENTS GENERAL DESCRIPTION... 35A-3 BASIC BRAKE SYSTEM DIAGNOSIS 35A-6
35A-1 GROUP 35A BASIC BRAKE SYSTEM CONTENTS GENERAL DESCRIPTION......... 35A-3 DIAGNOSIS 35A-6 INTRODUCTION..................... 35A-6 DIAGNOSTIC TROUBLESHOOTING STRATEGY......................... 35A-6
More informationDTC P0743 sets when the TCM detects an open circuit, a short to power, or a short to ground in the TCC PWM solenoid circuit for 1.5 seconds.
Page 1 of 5 2005 GMC Truck GMC K Sierra - 4WD Sierra, Silverado VIN C/K Service Manual Document ID: 1492351 DTC P0743 Circuit Description The torque converter clutch (TCC) solenoid is a pulse width modulated
More informationP0340-CAMSHAFT POSITION SENSOR CIRCUIT - BANK 1 SENSOR 1
11 - RT - CHRYSLER TOWN AND COUNTRY - 3.6L V6 V.V.T. P0340-CAMSHAFT POSITION SENSOR CIRCUIT - BANK 1 SENSOR 1 S109 K856 BR/YL K856 BR/YL 2 SENSOR CAMSHAFT POSITION 2 SENSOR CAMSHAFT POSITION 2 1 4 3 3
More informationGAS P0344-CAMSHAFT POSITION SENSOR INTERMITTENT
2007 Chrysler Truck PT Cruiser L4-2.4L VIN X Vehicle > ALL Diagnostic Trouble Codes ( DTC ) > Testing and Inspection > P Code Charts > P0344 GAS P0344-CAMSHAFT POSITION SENSOR INTERMITTENT https://my.alldata.com/repair/#/repair/article/55125/component/3926/itype/423/nonstandard/1175627
More informationDTC P0340 or P0341. DTC Descriptor DTC P0340. Camshaft position sensor circuit DTC P0341. Camshaft position sensor performance
DTC Descriptor DTC P0340 Camshaft position sensor circuit DTC P0341 Camshaft position sensor performance Circuit/System Description The camshaft position sensor each has 3 circuits consisting of an engine
More information2007 Chevrolet Corvette STEERING Steering Wheel and Column - Corvette. Steering Wheel and Column - Corvette
2007 STEERING Steering Wheel and Column - Corvette SPECIFICATIONS FASTENER TIGHTENING SPECIFICATIONS Fastener Tightening Specifications Specification Application Metric English Actuator Retaining Screws
More informationAdditions, Revisions, or Updates
1 03 13-17 SUBJECT DATE SPN 520268 (MCM) (GHG17) March 2017 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0193 DD Platform Med Duty SPN 520268/ FMI
More informationAdditions, Revisions, or Updates
1 06 10-16 SUBJECT SPN 111 (CPC) (GHG17) and SPN 111 (CPC) (EPA07;EPA10;GHG14) DATE June 2016 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0191
More informationMotorPro. ECM Troubleshooting Guide
MotorPro ECM Troubleshooting Guide Table of Contents ECM Service............ 1 Constant Torque 115 Volt High Voltage Check..... 2 Constant Torque 230 Volt High Voltage Check..... 3 Constant Torque 24
More informationDIAGNOSTIC REPORT. Vehicle Components. Vehicle Key Data Points
Page 1 of 5 Vehicle Components Engine Cummins 15.0L ISX3 79270697 03684275 04017048 030711195725 08000084 B0 BAC High/Low Speed Brakes Bendix EC-60 Premium ABS N/A BB40970 High/Low Speed Vehicle Key Data
More informationGROUP 17 CONTENTS WARNINGS REGARDING SERVICING OF SUPPLEMENTAL RESTRAINT SYSTEM (SRS) EQUIPPED VEHICLES
17-1 GROUP 17 CONTENTS ENGINE CONTROL 17-4 GENERAL DESCRIPTION 17-4 ENGINE CONTROL SYSTEM DIAGNOSIS 17-4 INTRODUCTION TO ENGINE CONTROL SYSTEM DIAGNOSIS 17-4 ENGINE CONTROL SYSTEM DIAGNOSTIC TROUBLESHOOTING
More informationU010C-LOST COMMUNICATION WITH TURBOCHARGER/ SUPERCHARGER CONTROL MODULE
2014 - D2 - RAM 3500 PICKUP - 6.7L I6 CUMMINS TURBO DIESEL U010C-LOST COMMUNICATION WITH TURBOCHARGER/ SUPERCHARGER CONTROL MODULE For a complete wiring diagram, refer to the Wiring Information. IGN RELAY-
More informationRWRG Fault Code 71 Pre-Authorization
RWRG0080 - Fault Code 71 Pre-Authorization Overview The UltraShift PLUS transmission uses the X-Y Shifter to engage and disengage a gear based on the driver s selected mode of operation. Gear disengagement
More informationAdditions, Revisions, or Updates
1 10 09-14 SUBJECT DATE SPN 5016 (ACM) (GHG14) October 2014 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change SPN 5016/FMI 3 - DDC-SVC-MAN-0084 GHG14 DD Platform
More informationAlternator Ground Check Verify Repairs
DDEC III/IV SINGLE ECM TROUBLESHOOTING GUIDE 16.3.6 Alternator Ground Check Perform the following steps to check the alternator ground. 1. Connect all connectors. 2. Remove alternator belt or disable alternator
More informationRECOMMENDED TOOLS PERSONAL & VEHICLE PROTECTION SAFETY GLASSES
PART NUMBER: 250-9625 GENERAL APPLICABILITY THIS CRUISE WAS TESTED AND VERIFIED ON: ALL MODELS RECOMMENDED TOOLS PERSONAL & VEHICLE PROTECTION SAFETY GLASSES KIT CONTENTS/SERVICE PARTS ITEM QTY DESCRIPTION
More informationAdditions, Revisions, or Updates
1 02 01-14 SUBJECT DATE SPN 1761/FMI 3, 4 ( ACM2-EPA10) (ACM2.1-GHG14) February 2014 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0084 DD Platform
More informationDIAGNOSIS AND TESTING
307-05-1 Automatic Transaxle/Transmission External Controls 307-05-1 DIAGNOSIS AND TESTING Visual Inspection Chart External Controls Mechanical Electrical Refer to Wiring Diagrams Cell 37 for schematic
More informationP0113-INTAKE AIR TEMPERATURE SENSOR 1 CIRCUIT HIGH
- DS - RAM 5 PICKUP - 4.7L MAGNUM V - DTC-Based Diagnostics/MODULE, Powertrain Control (PCM), NGC/Diagnosis and Testing P- SENSOR CIRCUIT HIGH AAT SENSOR GROUND BUS (+) BUS (-) ELECTRONICS POWER 4 C4 5
More information05/01/06 1er mai 2006 Cruise Control - Diagnostic Updates General Service Procedure Service Procedure Speed Control Diagnostic Tips Additional
05/01/06 1er mai 2006 General Service Procedure Service Procedure Speed Control Diagnostic Tips Additional Reference Information SPEED CONTROL DIAGNOSTICS - W/O SCP FORD: 2000-2003 Escort 2000-2004 Crown
More informationSPN 51 or Suspect Parameter Number (SPN) and Failure Mode Indicator (FMI) Description
SPN 51 or 3673 Suspect Parameter Number (SPN) and Failure Mode Indicator (FMI) Description SPN FMI Description Possible Causes 51 3 TPS1 Sensor Signal Voltage High Open/high resistance in low Short to
More informationP2314-IGNITION COIL 5 SECONDARY CIRCUIT - INSUFFICIENT IONIZATION - 5.7L/SRT8
- LC - DODGE CHALLENGER - 5.7L V8 HEMI MDS V.V.T. (EZH) P4-IGNITION COIL 5 SECONDARY CIRCUIT - INSUFFICIENT IONIZATION - 5.7L/SRT8 S9 IGNITION IGNITION 4 IGNITION 6 K7 DB/TN K5 DB/GY K DB/OR 9 C C COIL
More informationDJ - RAM 2500 PICKUP - 6.7L I6 CUMMINS TURBO DIESEL
2013 - DJ - RAM 2500 PICKUP - 6.7L I6 CUMMINS TURBO DIESEL 1 P202E-(DIESEL EXHAUST FLUID) REDUCTANT PERFORMANCE MODULE- POWERTRAIN CONTROL SIGNAL 77 K428 DB RETURN 53 C2 K426 DB/LG 1 SIGNAL 2 RETURN -
More information41 FLASH CODE 41 - TOO MANY SRS
41 FLASH CODE 41 - TOO MANY SRS Section Page 41.1 DESCRIPTION OF FLASH CODE 41... 41-3 41.2 SAE J1587 EQUIVALENT CODE FOR FLASH CODE 41... 41-3 41.3 TROUBLESHOOTING FLASH CODE 41... 41-4 41-2 From Bulletin
More informationCRUISE CONTROL SYSTEM
CRUISE CONTROL SYSTEM 1994 Toyota Celica 1994 ACCESSORIES & EQUIPMENT Toyota Motor Sales, U.S.A., Inc. - Cruise Control Systems Celica DESCRIPTION Cruise control system consists of Cruise Control Electronic
More informationP0123-THROTTLE POSITION SENSOR 1 CIRCUIT HIGH
- DS - RAM PICKUP -.7L MAGNUM V8 8 - DTC-Based Diagnostics/MODULE, Powertrain Control (PCM), NGC/Diagnosis and Testing P- POSITION SENSOR CIRCUIT HIGH VOLT SUPPLY MODULE- POWERTRAIN CONTROL 9 C F8 PK/YL
More information1999 Toyota RAV ACCESSORIES & EQUIPMENT Cruise Control Systems - RAV4
1999 ACCESSORIES & EQUIPMENT Cruise Control Systems - RAV4 DESCRIPTION WARNING: Deactivate air bag system before performing any service operation. See AIR BAG RESTRAINT SYSTEMS article. DO NOT apply electrical
More informationRECOMMENDED TOOLS PERSONAL & VEHICLE PROTECTION SAFETY GLASSES
PART NUMBER: 250-9545 GENERAL APPLICABILITY THIS CRUISE WAS TESTED AND VERIFIED ON:2.7,3.3, 3.5, 5.0 FORD F-150 RECOMMENDED TOOLS PERSONAL & VEHICLE PROTECTION SAFETY GLASSES KIT CONTENTS/SERVICE PARTS
More informationO2 Sensor Testing. If your engine has unexpectedly started to run poorly, an O2 Sensor Test should be performed.
O2 Sensor Testing If your engine has unexpectedly started to run poorly, an O2 Sensor Test should be performed. IMPORTANT: Testing the O2 sensors using the procedures below REQUIRES that the engine will
More informationVehicle Components. Vehicle Key Data Points
VIN Vehicle Make Model Model Year 2HSCUAPR48C687071 International Prostar 2008 Vehicle s Serial Number Software Version Network Engine Cummins 15.0L ISX1 79277503 03684275 05000708 072209134739 08000062
More informationTC Series Cooling Systems
TC Series Cooling Systems Table of Contents Table of Contents...1 List of Figures...1 Safety...2 Introduction...2 General Specifications...2 Types of Coolant...2 Routine Maintenance...2 Surge Tank Coolant
More informationQuickServe Online ( ) ISB6.7 CM2350 B101 Service Manual
Page 1 of 31 (/qs3/pubsys2/xml/en/manual/2883567/2883567-titlepage.html) Select Service Tools Recommended Cummins Service Tools 0.043 inch orificed diagnostic fuel line, Part Number 3164621 Diagnostic
More information2UZ-FE ENGINE CONTROL SYSTEM SFI SYSTEM
2UZ-FE ENGINE CONTROL SYSTEM SFI SYSTEM 347 P2120 Throttle / Pedal Position Sensor / Switch "D" Circuit P2122 Throttle / Pedal Position Sensor / Switch "D" Circuit Low Input P2123 Throttle / Pedal Position
More informationANTI-LOCK BRAKING SYSTEM (ABS)
35B-1 GROUP 35B ANTI-LOCK BRAKING SYSTEM (ABS) CONTENTS GENERAL DESCRIPTION......... 35B-2................ 35B-4 INTRODUCTION TO ANTI-LOCK BRAKING SYSTEM DIAGNOSIS................ 35B-4 ABS DIAGNOSTIC
More information5 Volt Sensor Supply Circuit - Test
Page 1 of 10 Shutdown SIS Previous Screen Product: INDUSTRIAL ENGINE Model: C4.4 INDUSTRIAL ENGINE 444 Configuration: C4.4 Industrial Engine 44400001-UP Troubleshooting C4.4 and C6.6 Industrial Engines
More informationSection 10 Chapter 7
Section 10 Chapter 7 24 Valve, 8.3 Liter Engine Troubleshooting Symptoms Identification Note: All coding used in the 8.3 Liter and 9 Liter engine manuals are Cummins engine codes. These engine codes have
More informationGENESIS Electronic Brake Controller Hayes Brake Controller Company - P/N 81790
GENESIS Electronic Brake Controller Hayes Brake Controller Company - P/N 81790 INSTALLATION MANUAL For trailers with 2-8 electric brakes and vehicles with 12 volt negative ground systems only. READ AND
More informationHOW TO PROCEED WITH TROUBLESHOOTING
2005 BRAKES Anti-Lock Brake System With Electronic Brake Force Distribution (EBD) - Diagnostics - RAV4 HOW TO PROCEED WITH TROUBLESHOOTING Troubleshoot in accordance with the following procedures. Fig.
More informationRECOMMENDED TOOLS PERSONAL & VEHICLE PROTECTION SAFETY GLASSES
2014 FORD TRANSIT FULL SIZE PART NUMBER: 250-9636 GENERAL APPLICABILITY THIS CRUISE WAS TESTED AND VERIFIED ON: FORD TRANSIT 150, 250 RECOMMENDED TOOLS PERSONAL & VEHICLE PROTECTION SAFETY GLASSES KIT
More informationRECOMMENDED TOOLS PERSONAL & VEHICLE PROTECTION SAFETY GLASSES
PART NUMBER: 250-9631 GENERAL APPLICABILITY THIS CRUISE WAS TESTED AND VERIFIED ON: ALL MODELS (AT/MT) RECOMMENDED TOOLS PERSONAL & VEHICLE PROTECTION SAFETY GLASSES KIT CONTENTS/SERVICE PARTS ITEM QTY
More information