CV3000 Series Pressure Balanced Cage type Control Valve

Transcription

1 No. SS CV3000 Series Pressure Balanced Cage type Control Valve OVERVIEW Model HCB Pressure Balanced Cage Type Control Valves are designed for heavy duty services. The compact valve body, having a S-shape flow passage that features low pressure loss and a stabilizer that regulates turbulent flow around the cage, allows a large flow capacity, rangeability, and high accuracy flow characteristics. The valve plug is structured in a pressure-balanced type that permits flow control of a high differential pressure with a small actuating force. The actuator integrated with simplest mechanisms utilizes a compact yet powerful diaphragm actuator loaded with multiple springs. The model HCB valves are widely applicable for reliable control of high or low temperature, high pressure or high differential pressure process lines where dynamic stability, low noise, and cavitation/flashing resistance are required. Model HCB SPECIFICATIONS Body Type Straight-through, cast globe valve Nominal size 1½, 2, 2½, 3, 4, 6, 8 inches Pressure rating JIS 10K, 16K, 20K, 30K, 40K ANSI Class 125, 150, 300, 600 JPI Class 125, 150, 300, 600 End connection Flanged end; Connection type Pressure rating Applicable standard JIS10K JIS B FF ANSI Class 125 ANSI B JPI Class 125 JPI-7S JIS10K, 16K, 20K, 30K, 40K JIS B RF ANSI Class 150, 300, 600 ANSI B JPI Class150, 300, 600 JPI-7S RJ, LG ANSI Class 150, 300, 600 ANSI B JPI Class 150, 300, 600 JPI-7S Tongue and groove(groove) Male and female(female) JIS16K, 20K, 30K, 40K JIS B Welded end; SW (1½, 2 inches) BW (2½ to 8 inches) Material For body/trim material combinations and operating temperature ranges, refer to Table 1. Bonnet Plain bonnet (-17 to 230 C) Extension bonnet type 1 (-45 to -17 C and 230 to 566 C) Extension bonnet type 2 Integral cast type (-100 to -45 C) Welded type (-196 to -100 C) Bellows type For operating temperature and pressure range, refer to Figure 3. Note) Take care not to exceed the operating temperature ranges specified for respective materials. Gland type Bolted gland th edition

2 No. SS Packing / Grease Grease not provided When V shaped PTFE packing or PTFE yarn packing is used. Grease provided When graphite packing is used. Gasket Type Combination of serrated type and spiral wound type (integral cage), Serrated type (split cage) Material Stainless steel (SUS316, SUS316L, SUS329J1), copper, aluminum Trim Valve plug Pressure balanced type Cage High-capacity (For flow characteristics, refer to Figure 1.) -Metal seat: Equal percentage (%V) Linear (LV) -Soft seat: Equal percentage (%T) Linear (LT) High-flow characteristics type -Metal seat (For flow characteristics, refer to Figure 2.) Equal percentage (%VF) Linear (LVF) -Soft seat (For flow characteristics, refer to Figure 2.) Equal percentage (%TF) Linear (LTF) Note) 1.For cage design (integral cage or splie cage) refer to Table 1. 2.For operating temperature and maximum differential pressure range of soft-seat type, refer to Figure 4. Material For body/trim material combinations and operating temperature ranges, refer to Table 1 Note) For fluid conditions that require Stellite, refer to Figure 5. Type Single acting diaphragm actuator (Type PSA1, HA or VA5) Spring Type piston actuator (Type PSA6R) Action Direct or reverse action Diaphragm Type PSA1, HA: Cloth embedded ethylene propylene rubber Type VA: Cloth-embedded chloroprene rubber Spring range Type PSA1, HA or VA5 {0.2 to 1.0 kgf/cm 2 }, 40 to 120 {0.4 to 1.2 kgf/cm 2 }, {0.8 to 2.4 kgf/cm 2 } Type PSA6R 200 to 340 {2.0 to 3.5 kgf/cm 2 } 200 to 390 {2.0 to 4.0 kgf/cm 2 } Azbil Corporation Supply pressure Diaphragm actuator Type PSA1, HA: 140 to 390 {1.4 to 4.0 kgf/cm²} Type VA5: 140 to 270 {1.4 to 2.8 kgf/cm²} Spring type piston actuator Type PSA6R: 400 to 500 {4 to 5kgf/cm²} Note) Allowable differential pressure varies depending on spring range and air supply pressure. Air connection Rc1/4 or 1/4NPT internal thread Note) With Type VA, Rc¼ or ¼NPT adapter is provided on Rc½ internal thread (also providing Rc3/8 adapter is possible). Ambient temperature -30 to 70 C Valve action Air-to-close (Direct action actuator is combined.) Air-to-open (Reverse action actuator is combined.) Optional accessories *, pressure regulator with filter, hand wheel*, limit switch, solenoid valve, motion transmitter, booster relay, lock-up valve, and others. Note) 1. For the optional items, refer to the specification sheets and installation drawings of respective accessories. 2. Accessories with the asterisk mark (*) are selected from among the following types depending on the actuators to be combined. Hand wheel P/P I/P Top Side PSA1 VPE AVP/HEP THM SHM HA2 to 4 HTP AVP/HEP THM SHM VA5 HTP AVP/HEP THM SHM PSA6 HTP/VPP AVP/HEP - SHM Additional specification (by special order) Special inspection Flow characteristics inspection, material inspection (Material certificate), non-destructive inspection, steam inspection, low-temperature inspection With drain plug Double gland Oil/water free treatment Copper free treatment York material SCPH2 (York material of PSA1 is SCPH2 as standard.) - 2 -

3 Azbil Corporation Stainless steel (SUS304) atmosphere-exposed nuts and bolts Special air piping and joint Sand-/dust-preventive measure Saline damage countermeasure Cold-area use specifications Tropical-area use specifications Vacuum service Performance Rated Cv value Refer to Table 2. Flow characteristics Refer to Figure 1 and Figure 2. Inherent rangeability 50: 1 Optional 75 : 1 for full port size Allowable differential pressure Refer to Table 8 to Table 15. Leakage specification IEC :2006 or JIS B :2008 Metal seat Standard... Class II: Leakage less than 0.5% of maximum valve capacity. Option... Class III: Leakage less than 0.1% of maximum valve capacity. Note) If you require leakage Class IV, please refer to model ACP (No.SS2-ACP ). Soft seat Class VI: Leakage % of maximum valve capacity. No. SS Hysteresis error Without positioner:within 3% F.S. (Within 5% F.S.) ((Within 9% F.S.)) With positioner: Within 1% F.S. ((Within 2% F.S.)) Linearity Without positioner:within ± 5% F.S. ((Within 9% F.S.)) With positioner: Within ± 1% F.S. ((Within 2% F.S.)) (VPE : Within ±3% F.S., AVP/HEP : Within ±2% F.S.) Note) 1. When positioner is not provided, operating performance may vary depending on type of packings used. 2. Parenthesized figures are applicable to type PSA1. 3. Double parenthesized figures are applicable to type PSA6. Dimensions Refer to Figure 7 and Table 16 and Table 17 Weight Refer to Table 18. orientation Refer to Figure 8. Finish Blue (Munsell 10B5/10) or silver, or other specified colors

4 No. SS Azbil Corporation Table 1 Body / trim material combinations and operating temperature ranges ( C) Body Material JIS SCPH2 SCPH21 SCPH61 SCPL1 SCS11 SCS13A SCS14A SCS16A SCS19A Trim material ASTM A216WCB A217WC6 A217C5 A352LCB A351CF8 A351CF8M A351CF3M A351CF3 JIS SCS24-5 to to to to 350 JIS SCS11-50 to to 300 JIS SCS14A -5 to 300* -5 to 300* -5 to 300* -45 to to to 300 JIS SCS16A -45 to to to to JIS SCS19A -45 to to to to 300 JIS SCS11 Stellite -50 to to 550 JIS SCS14A Stellite -5 to 425* -5 to 550* -5 to 556* -45 to to to 550 JIS SCS16A Stellite -45 to to to to 450 JIS SCS19A Stellite to to to to 450 JIS SCS14A Atomlloy -5 to 425* -5 to 500* -5 to 500* JIS SCS14A Soft seat -5 to to to to 200 JIS SCS16A Soft seat -45 to to to to to 200 Note) 1. Asterisk marked (*) combinations, split cages are used when fluid temperature exceeds 230 C and valve size is greater than 3 inches. 2. shows standard combination of valve body and trim materials. Cv value and travel Table 2 High-capacity type cage (%V, LV, %T, LT) Nominal size (inches) 1½ 2 2½ Port size (inches) 1½ 2 2½ Rated Cv value Metal or soft seat type Equal percentage characteristics (%V,%T) Metal or soft seat type Linear characteristics (LV, LT) Rated travel (mm) Cv value (%) Cv value (%) Travel (%) Travel (%) a. Equal percentage characteristics b. Linear characteristics (%V: metal seat, %T: soft seat) (%LV: metal seat, LT: soft seat) Figure 1 Flow characteristics: High-capacity type Table 3 High-flow characteristic type cage (%VF, LVF, %TF, LTF) Nominal size (inches) 1½ 2 2½ Port size (inches) 1 1¼ 1½ 1¼ 1½ 2 1½ 2 2½ 2 2½ 3 2½ Rated Cv value (%VF, LVF, %TF, LTF) Rated travel (mm)

5 Azbil Corporation No. SS Cv value (%) Cv value (%) Cv value (%) Cv value (%) Travel (%) Travel (%) Travel (%) Travel (%) a. Equal percentage characteristics (%VF: metal seat) b. Linear characteristics (LVF: metal seat) Note) The above graphs indicate typical flow characteristics. c. Equal percentage characteristics (%TF: Soft seat) Figure 2 Flow characteristics: High-flow characteristic type cage d. Linear characteristics (LTF: Soft seat) Maximum pressure(mpa) Welded bellows Formed bellows type II Formed bellows type I Fluid temperature ( C) Figure 3 Bellows Type by Temperature and Pressure Ranges Note) Bellows type are classified into Formed bellows type I, II and welded bellows by temperature and pressure ranges. Please refer to No. SS2-BSL about detail of bellows specification. Maximum differential pressure {kgf/cm 2 } {30} 1470 {15} Glass-inserted PTFE PTFE Carbonfiber inserted PTFE Fluid temperature ( C) {30} 1470 {15} 490 {5} Figure 4 Temperature and maximum differential pressure range of soft-seat type Note) If there is any possibility to cause erosion due to saturated steam or superheated-water, use the metal seat. Maximum pressure {kgf/cm 2 } 1470 {15} 981 {10} 490 {5} Stellite Fluid temperature ( C) Figure 5 Temperature / normal differential pressure ranges requiring Stellite Note) 1. SCS24 (Precipitation-hardened stainless steel) requires no Stellite. 2. For cavitation / flashing service or oil free service, SCS24 or Stellite is recommended regardless of temperature and differential pressure

6 No. SS Azbil Corporation Structural drawing of trim and body/trim material combinations Following table shows typical body/trim material combinations. Please contact us about materials that are not listed in this table. 3 Piston ring Valve stem Bonnet gasket Valve plug Cage Seat gasket 3Piston ring Valve stem Bonnet gasket Valve plug Cage Seat ring a. Integral cage type (Plain bonnet) b. Split cage type (Extension bonnet type1) Figure 6 Structual drawing of trim Table 4 The valve body material is carbon steel (SCPH2/A216WCB) and plain bonnet. Valve plug Cage Piston ring *1 Valve stem Note) *1. For gas or steam only. Figure 5-1 SCS24 SCS14A SCS14A Stellite SCS14A Soft seat General Oil free General Ni-resist Stellite #21 SUS316 Spiral wound(hoop: SUS316, filler: Spiral wound(hoop: Spiral wound(hoop: SUS316, Seat gasket Inorganic paper) SUS316, filler: PTFE) filler: Inorganic paper) Bonnet gasket SUS316 SUS316(PTFE coating) SUS316 Table 5 The valve body material is carbon steel (SCPH2/A216WCB) and Extension bonnet type1. Valve plug Cage Piston ring *1 SCS24 Note) *1. For gas or steam only. *2. For split cage only. Figure 5-1 Figure 5-2 SCS14A SCS14A SCS14A Stellite Austenitic cast iron Seat ring *2 SCS14A Valve stem Seat gasket Bonnet gasket Spiral wound(hoop: SUS316, filler: Inorganic paper) SUS316 SUS316 SCS14A Stellite SCS14A Stellite - 6 -

7 Azbil Corporation No. SS Table 6 The valve body material is stainless steel (SCS13A/A351CF8 or SCS14A/A351CF8M) and plain bonnet Valve plug Cage Piston ring *1 Valve stem Seat gasket Note) *1. For gas or steam only. Figure 5-1 SCS14A SCS14A Stellite SCS14A Soft seat General Oil free General Ni-resist Stellite #21 SUS316 Spiral wound(hoop: SUS316, Filler: Inorganic paper) Spiral wound(hoop: SUS316, Filler: PTFE) Spiral wound(hoop: SUS316, Filler: Inorganic paper) Bonnet gasket SUS316 SUS316(PTFE coating) SUS316 Table 7 The valve body material is stainless steel (SCS13A/A351CF8 or SCS14A/A351CF8M) and extension bonnet type1 Valve plug Cage Piston ring *1 SCS24 Note) *1. For gas or steam only. *2. For split cage only. Figure 5-1 Figure 5-2 SCS14A SCS14A SCS14A Stellite Austenitic cast iron Seat ring *2 SCS14A Valve stem Seat gasket Bonnet gasket Spiral wound(hoop: SUS316, Filler: Inorganic paper) SUS316 SUS316 SCS14A Stellite SCS14A Stellite - 7 -

8 No. SS Azbil Corporation Allowable differential pressure Metal seat (%VF, LVF, %V, LV) : PTFE packing Valves with type PSA, HA actuator Table 8 Air-to-close model No. PSA1D HA2D HA3D HA4D Supply pressure 160 {1.6} 390 {4.0} 160 {1.6} 390 {4.0} 160 {1.6} 390 {4.0} 160 {1.6} 390 {4.0} Spring range Differential pressure (by nominal size (inches)) 1½ 2 2½ {5.1} 390 {4.0} {25.0} {19.0} {76.0} {59.0} {9.9} {7.7} {38.0} {49.2} {17.5} {13.7} {87.0} {67.0} 650 {6.6} 3230 {32.9} 9680 {98.7} 1150 {11.7} 5690 {58.0] 1980 {20.2] 530 {5.4} 2690 {27.4} 410 {4.2] 2040 {20.8} {82.3} {62.8} {9.7} {7.4} {37.0} {48.7} {16.7] {12.8} {83.9} {63.6} {100] 510 {5.2} 2560 {26.1} 7710 {78.6} {9.0} {7.4} {37.0} {45.0} {100] Note) 1. shows a model with standard actuator. 2. : is necessary, : Can be operated either with or without positioner. 3. Take care not to cause the maximum allowable differential pressure to exceed the maximum operating pressure designated by ANSI B or JIS B The upper figures denote the operating allowable differential pressure. The lower denote allowable differential pressure at full closure

9 Azbil Corporation No. SS Metal seat (%VF, LVF, %V, LV) : PTFE packing Valves with type PSA, HA actuator Table 9 Air-to-open model No. PSA1R HA2R HA3R HA4R HR5R PSA6R Supply pressure 140{1.4} 270{2.8} 140{1.4} 270{2.8} 140{1.4} 270{2.8} 140{1.4} 270{2.8} 140{1.4} 140{1.4} 270{2.8} 400{4.0} 500{5.0} Differential pressure (by nominal size (inches)) Spring range 1½ 2 2½ to 120 {0.4 to 1.2} 200 to 340 {2.0 to 3.5} 200 to 390 {2.0 to 4.0} {5.1} {4.0} {35.0} {27.0} {9.9} {7.7} {6.6} {5.4} {4.2} {38.4} {29.3} {68.1} {53.9} {46.0} {17.5} {13.7} {11.7} {9.7} {7.4} {5.2} {36.7} {95.7} {81.7} {68.0} {51.8} {20.2] {16.7} {12.8} {9.0} {7.4} {89.7} {63.0} {51.0} {17.5} {12.3} {10.2} {37.0} {30.7} {52.0} {100] {80.0} {70.0} Note) 1. shows a model with standard actuator. 2. : is necessary, : Can be operated either with or without positioner. 3. Take care not to cause the maximum allowable differential pressure to exceed the maximum operating pressure designated by ANSI B or JIS B The upper figures denote the operating allowable differential pressure. The lower denote allowable differential pressure at full closure

10 No. SS Azbil Corporation Soft seat (%TF, LTF, %T, LT) Table 10 Air-to-close model No. PSA1D HA2D HA3D HA4D Supply pressure 140{1.4} 160{1.6} 390 {4.0} 160 {1.6} 390 {4.0} 160 {1.6} 390 {4.0} 160 {1.6} 390 {4.0} Differential pressure (by nominal size (inches)) Spring range 1½ 2 2½ * {3.6} 1670 {17.0} 680* {6.9} 1210* {12.3} 270* {2.8} 1270 {13.0} 530* {5.4} 2610 {26.6} 940* {9.6} 450* {4.6} 2260 {23.0} 800* {8.2} 1380* {14.1} 370* {3.8} 1880 {19.2} 670* {6.8} 1150* {11.7} 280* {2.9} 1430 {14.6} 510 {5.2} 2540 {25.9} 880* {9.0} 350* {3.6} 1790 {18.3} 620* {6.3} 510 {5.2} 2540 {25.9} Table 11 Air-to-open model No. PSA1R HA2R HA3R HA4R Supply pressure 270 {2.8} 270 {2.8} 270 {2.8} 270 {2.8} Spring range Differential pressure (by nominal size (inches)) 1½ 2 2½ * {3.6} 2450 {25.0} 680* {6.9} 1210* {12.3} 270* {2.8} 1860 {19.0} 530* {5.4} 940* {9.6} 450* {4.6} 800* {8.2} 1380* {14.1} 370* {3.8} 2640 {26.9} 670* {6.8} 1150* {11.7} 280* {2.9} 2010 {20.5} 510* {5.2} 880* {9.0} 350* {3.6} 2520 {25.7} 620* {6.3} 510* {5.2} Note) 1. shows a model with standard actuator. 2. : is necessary, : Can be operated either with or without positioner. 3. Take care not to cause the maximum allowable differential pressure to exceed the maximum operating pressure designated by ANSI B or JIS B Seat leakages of items marked with asterisk(*) are less than 0.01% (Class IV). Those for items without asterisk marks(*) are less than % (Class VI)

11 Azbil Corporation No. SS Metal seat (%VF, LVF, %V, LV): Graphite packing "P6610CH+P6528" (+230 to +500 C) Valves with type PSA, HA or VA actuator Table 12 Air-to-close model No. Supply pressure Spring range Differential pressure (by nominal size (inches)) 1½ 2 2½ HA2D 390 {4.0} HA3D 390 {4.0} HA4D 390 {4.0} 9550 {97.3} 8150 {83.1} 6790 {69.2} 5180 {52.8} 9190 {93.7} 6490 {66.1} 9360 {95.4} Note) 1) shows a model with standard actuator. 2): is necessary. 3) Take care not to cause the maximum allowable differential pressure to exceed the maximum operating pressure designated by ANSI B or JIS B ) The upper figures denote the operating allowable differential pressure. The lower denote allowable differential pressure at full closure. Table 13 Air-to-open Model No. Supply pressure Spring range Differential pressure (by nominal size (inches)) 1½ 2 2½ HA2R 270{2.8} HA3R 270{2.8} HA4R 270{2.8} VA5R 270{2.8} PSA6R 400{4.0} *1 500{5.0} *2 400{4.0} *3 200 to 340 {2.0 to 3.5} 200 to 390 {2.0 to 4.0} 200 to 340 {2.0 to 3.5} 5320 {54.2} 9450 {96.3} {36.1} {42.4} {75.2} {64.2} 2960 {30.1} 5250 {53.5} 2250 {22.9} {28.8} {40.7} {74.3} {52.5} {96.4} {68.2} 4200 {42.8} 5450 {55.5} - Note) 1) shows a model with standard actuator. 2): is necessary. 3) Take care not to cause the maximum allowable differential pressure to exceed the maximum operating pressure designated by ANSI B or JIS B ) The upper figures denote the operating allowable differential pressure. The lower denote allowable differential pressure at full closure. 5) *1.. Applicable to valve sizes of 21/2 to 4 inches, *2.. Applicable to valve size of 6 inches, *3.. Applicable to valve size of 8 inches

12 No. SS Azbil Corporation Metal seat (%VF, LVF, %V, LV): Graphite packing "P6610CH+M8590" (+500 to +566 C) Valves with type PSA, HA or VA actuator Table 14 Air-to-close model No. Supply pressure Spring range Differential pressure (by nominal size (inches)) 1½ 2 2½ HA2D 390 {4.0} HA3D 390 {4.0} HA4D 390 {4.0} 8940 {91.1} 7630 {77.8} 6350 {64.7} 4850 {49.4} 8600 {87.6} 6080 {61.9} 8880 {90.5} Note) 1) shows a model with standard actuator. 2): is necessary. 3) Take care not to cause the maximum allowable differential pressure to exceed the maximum operating pressure designated by ANSI B or JIS B ) The upper figures denote the operating allowable differential pressure. The lower denote allowable differential pressure at full closure. Table 15 Air-to-open model No. Supply pressure Spring range Differential pressure (by nominal size (inches)) 1½ 2 2½ HA2R 270{2.8} HA3R 270{2.8} HA4R 270{2.8} VA5R 270{2.8} PSA6R 400{4.0} *1 500{5.0} *2 400{4.0} *3 200 to 340 {2.0 to 3.5} 200 to 390 {2.0 to 4.0} 200 to 340 {2.0 to 3.5} {36.0} {46.1} {82.0} {64.1} 3020 {30.7} 5360 {54.6} 2520 {25.6} 1920 {19.5} {34.7} {45.5} {86.3} {65.8} 8060 {82.1} 2410 {24.5} {37.8} {46.4} {58.0} {47.3} Note) 1) shows a model with standard actuator. 2): is necessary. 3) Take care not to cause the maximum allowable differential pressure to exceed the maximum operating pressure designated by ANSI B or JIS B ) The upper figures denote the operating allowable differential pressure. The lower denote allowable differential pressure at full closure. 5) *1.. Applicable to valve sizes of 21/2 to 4 inches, *2.. Applicable to valve size of 6 inches, *3.. Applicable to valve size of 8 inches

13 Azbil Corporation DIMENSIONS Table 16 Face-to-face dimensions No. SS [Unit: mm] Nominal size (inches) JIS 10KFF, RF ANSI 125FF ANSI 150RF JPI 150RF * JIS 16KRF JIS 20KRF JIS 30KRF ANSI 300RF JPI 300RF * JIS 40KRF ANSI 600RF JPI 600RF * A JIS 16K Tongue and groove Male and female JIS 20K Tongue and groove Male and female JIS 30K Tongue and groove Male and female JIS 40K Tongue and groove Male and female 1½ ½ Nominal size (inches) ANSI 150RJ JPI 150RJ ANSI 300RJ JPI 300RJ ANSI 600RJ JPI 600RJ Note) * : Face-to-face dimensions conform to following standards. - IEC : IEC : 1998 (2½ inches or over) - JIS B : JIS B : 2005 (2½ inches or over) A ANSI 300LG JPI 300LG ANSI 600LG JPI 600LG ANSI 150 JPI 150SW, BW * ANSI 300, 600 JPI 300, 600SW, BW * 1½ ½ B B H H H H E E E E A A A A a. For PSA1 actuator b. For HA actuator c. For VA5 actuator d. For PSA6 actuator Figure 7 Face-to-face and external dimensions

14 No. SS Azbil Corporation Table 17 External dimensions [Unit: mm] Nominal size (inches) 1½ 2 2½ model No. Plain bonnet Extension bonnet Type 1 H Extension bonnet Type 2 Integral cast type Welded type Bellows type bonnet B B E PSA1D, R HA2D, R HA3D, R PSA1D, R HA2D, R HA3D, R HA2D, R / HA3D, R / HA4D, R / HA2D, R / HA3D, R / HA4D, R / HA2D, R / HA3D, R / HA4D, R / VA5R PSA6R HA3D, R / HA4D, R / VA5R PSA6R HA4D, R VA5R PSA6R Note) 1. H dimensions are applicable when a hand wheel is not provided. When top mounted hand wheel HA or VA actuators or side mounted hand wheel PSA6R actuators are used, add the hand wheel dimentsions designated in respective specification sheets (No.SS for Type HA actuators, No.SS for Type VA actuators and SS2-PSA for Type PSA actuators). 2. H dimensions of Extension bonnet Type 1 are as follows: The left side JIS 10K and ANSI 150, and the right side for JIS 16K and ANSI 300 or over

15 Azbil Corporation No. SS Table 18 Weight [Unit: kg] Weight Nominal size (inches) 1½ 2 2½ model No. Flanged type JIS 10K, ANSI/JPI 150 Plain bonnet Extension Type 1, Bellows type Extension Type 2 Integral cast type Welded type Plain bonnet Flanged type JIS 16K, 20K, 30K ANSI/JPI 300 Extension Type 1, Bellows type Extension Type 2 Integral cast type Welded type Plain bonnet Flanged type JIS 40K ANSI/JPI 600 Extension Type 1, Bellows type Extension Type 2 Integral cast type Welded type Plain bonnet Welded type JIS10K,16K,20K, 30K ANSI/JPI150,300,600 Extension Type 1, Bellows type Extension Type 2 Integral cast type PSA1D, R HA2D, R HA3D, R PSA1D, R HA2D, R HA3D, R HA2D, R HA3D, R HA4D, R HA2D, R HA3D, R HA4D, R HA2D, R HA3D, R HA4D, R VA5R PSA6R HA3D, R HA4D, R VA5R PSA6R HA4D, R VA5R PSA6R Welded type

16 No. SS Azbil Corporation Flow direction Side-mounted hand wheel Flow direction Flow direction Flow direction Side-mounted hand wheel Side-mounted hand wheel Side-mounted hand wheel Side-mounted hand wheel Flow direction Flow direction Flow direction Flow direction No.1 (Standard type) No.2 No.3 No.4 Figure 8 orientation Note) 1. Indicate by position number when installation other than the standard type is required. 2. With Type PSA6R actuator, the side-mounted hand wheel is mounted on the same side as the positioner. Ordering information When ordering, please specify; 1) Model number: HCB 2) Nominal size Port size 3) Type and rating of end connections 4) Body and trim material, necessity of hardening 5) Type of bonnet 6) Valve and plug characteristics 7) Type of actuator, air pressure to diaphragm 8) Valve action (direct or reverse) 9) Accessories (positioner, hand wheel, pressure regulator with filter and etc.) 10) 11) 12) 13) 14) 15) Special requirement of degreasing, copper free treatment, and etc. Name of flow medium Normal flow and maximum required flow Pressure of flow medium, upstream and downstream pressure at maximum and minimum, required flow Temperature and specific gravity of flow medium Viscosity of flow medium, inclusive or exclusive of slurry

17 Note

18

19

20 Please, read Terms and Conditions from following URL before the order and use. Specifications are subject to change without notice Kawana, Fujisawa Kanagawa Japan (11) 1st edition: Mar th edition: Aug No part of this publication may be reproduced or duplicated without the prior written permission of Azbil Corporation.