Fugitive Emission Gasket Test Report
|
|
|
- Jemima Jacobs
- 6 years ago
- Views:
Transcription
1 Fugitive Emission Gasket Test Report Chevron Fugitive Emission Test (CFET), March 2013 Performed for Environmental Gasket Co. 6 inch Class 300 Fishbone Gasket Project Number: Test Start Date: November6, 2013 Performed by YARMOUTH RESEARCH AND TECHNOLOGY, LLC 434 Walnut Hill road North Yarmouth, ME USA (207) info@yarmouthresearch.com
2 DATA SUMMARY Customer: Environmental Gasket Co. Start Date: 6-Nov-13 Project #: Gasket Description: Fishbone Gasket Test Description: Chevron Fugitive Emissions Test (CFET) Protocol for Pipe Flange Gaskets, 3/1/2013 Gasket Size / Class: 6 inch ANSI Class 300 Flange Condition: New Test Media / Pressure: 600 psig Methane Test Results: The average and maximum leakage results shown below were calculated from 60 readings measured during a minute duration. See data sheets for more detailed information. Test Procedure: Score grooves on outer rings - both sides: Yes Measure OD of Sealing Surface: 8.38 inches Measure ID of Sealing Surface: 7.00 inches Measure gasket thickness (4): 0.160, 0.159, 0.159, Outer ring thickness: inches Lube studs and nuts with Jet-Lube 550 Extreme: Yes Assemble gasket in flanges with 190 ft-lb nut torque: Yes Verify parallelism is within.010 inch: Yes Compressed Gasket Thickness: inches Pressurize with 600 psig methane for 15 minutes: Yes Thermal Cycling Perform thermal cycle and record leakage readings below: Heat 1 flange only. Record other flange temp when heated flange reaches 500F. Reduce pressure to 0, zero meter, repressurize, dwell 15 min. Yes Yes Yes Yes
3 Thermal Leakage Readings (PPMv) Flange Temperatures Cycle Ambient Temp. 500 deg F Temp. Heated Other Number Avg. Max. Avg. Max. (deg F) (deg F) Start Averages -> Maximums -> Gasket thickness at end of test: inches The gasket passed the leakage requirements of the test with all leakages being below 500 PPMv. Tested by:
4 Test Gasket as Received
5 Grooves cut in out ring to prevent sealing.
6 Thermal Cycle Number: 0 Date 11/6/ :08:43 AM :08:44 AM :08:45 AM :08:46 AM :08:47 AM :08:48 AM :08:49 AM :08:50 AM :08:51 AM :08:52 AM :08:53 AM :08:53 AM :08:54 AM :08:55 AM :08:56 AM :08:57 AM :08:58 AM :08:59 AM :09:00 AM :09:01 AM :09:02 AM :09:03 AM :09:04 AM :09:05 AM :09:06 AM :09:07 AM :09:08 AM :09:09 AM :09:10 AM :09:11 AM :09:12 AM :09:13 AM :09:14 AM :09:15 AM :09:16 AM :09:17 AM :09:18 AM :09:19 AM :09:20 AM :09:21 AM :09:22 AM :09:23 AM :09:24 AM :09:25 AM :09:26 AM :09:27 AM :09:28 AM :09:29 AM :09:30 AM :09:31 AM :09:32 AM :09:33 AM :09:34 AM :09:35 AM :09:36 AM :09:37 AM :09:38 AM :09:39 AM :09:40 AM :09:41 AM Averages -> Maximum -> 1.1
7 Thermal Cycle Number: 0 Date 11/6/2013 5:39:08 PM :39:09 PM :39:10 PM :39:11 PM :39:12 PM :39:13 PM :39:14 PM :39:15 PM :39:16 PM :39:17 PM :39:18 PM :39:19 PM :39:20 PM :39:21 PM :39:22 PM :39:23 PM :39:24 PM :39:25 PM :39:26 PM :39:27 PM :39:28 PM :39:29 PM :39:30 PM :39:31 PM :39:32 PM :39:33 PM :39:34 PM :39:35 PM :39:35 PM :39:36 PM :39:37 PM :39:38 PM :39:39 PM :39:40 PM :39:41 PM :39:42 PM :39:43 PM :39:44 PM :39:45 PM :39:46 PM :39:47 PM :39:48 PM :39:49 PM :39:50 PM :39:51 PM :39:52 PM :39:53 PM :39:54 PM :39:55 PM :39:56 PM :39:57 PM :39:58 PM :39:59 PM :40:00 PM :40:01 PM :40:02 PM :40:03 PM :40:04 PM :40:05 PM :40:06 PM Averages -> Maximum -> 12.1
8 Thermal Cycle Number: 1 Date 11/7/ :25:33 AM :25:34 AM :25:35 AM :25:36 AM :25:37 AM :25:38 AM :25:39 AM :25:40 AM :25:41 AM :25:42 AM :25:43 AM :25:44 AM :25:45 AM :25:46 AM :25:47 AM :25:48 AM :25:49 AM :25:50 AM :25:51 AM :25:52 AM :25:53 AM :25:54 AM :25:55 AM :25:56 AM :25:57 AM :25:58 AM :25:59 AM :26:00 AM :26:01 AM :26:02 AM :26:03 AM :26:04 AM :26:05 AM :26:06 AM :26:07 AM :26:08 AM :26:09 AM :26:10 AM :26:11 AM :26:12 AM :26:13 AM :26:14 AM :26:15 AM :26:16 AM :26:17 AM :26:18 AM :26:19 AM :26:20 AM :26:21 AM :26:22 AM :26:23 AM :26:24 AM :26:25 AM :26:26 AM :26:27 AM :26:28 AM :26:29 AM :26:30 AM :26:31 AM :26:32 AM Averages -> Maximum -> 15.1
9 Thermal Cycle Number: 1 Date 11/7/2013 1:52:43 PM :52:44 PM :52:44 PM :52:45 PM :52:46 PM :52:47 PM :52:48 PM :52:49 PM :52:50 PM :52:51 PM :52:52 PM :52:53 PM :52:54 PM :52:55 PM :52:56 PM :52:57 PM :52:58 PM :52:59 PM :53:00 PM :53:01 PM :53:02 PM :53:03 PM :53:04 PM :53:05 PM :53:06 PM :53:07 PM :53:08 PM :53:09 PM :53:10 PM :53:11 PM :53:12 PM :53:13 PM :53:14 PM :53:15 PM :53:16 PM :53:17 PM :53:18 PM :53:19 PM :53:20 PM :53:21 PM :53:22 PM :53:23 PM :53:24 PM :53:25 PM :53:26 PM :53:27 PM :53:28 PM :53:29 PM :53:30 PM :53:31 PM :53:32 PM :53:33 PM :53:34 PM :53:35 PM :53:36 PM :53:37 PM :53:38 PM :53:39 PM :53:40 PM :53:41 PM Averages -> Maximum -> 10.6
10 Thermal Cycle Number: 2 Date 11/8/ :31:09 AM :31:10 AM :31:11 AM :31:12 AM :31:13 AM :31:14 AM :31:15 AM :31:16 AM :31:17 AM :31:18 AM :31:19 AM :31:20 AM :31:21 AM :31:22 AM :31:23 AM :31:24 AM :31:25 AM :31:26 AM :31:27 AM :31:28 AM :31:29 AM :31:30 AM :31:31 AM :31:32 AM :31:33 AM :31:34 AM :31:35 AM :31:36 AM :31:37 AM :31:38 AM :31:39 AM :31:40 AM :31:41 AM :31:41 AM :31:42 AM :31:43 AM :31:44 AM :31:45 AM :31:46 AM :31:47 AM :31:48 AM :31:49 AM :31:50 AM :31:51 AM :31:52 AM :31:53 AM :31:54 AM :31:55 AM :31:56 AM :31:57 AM :31:58 AM :31:59 AM :32:00 AM :32:01 AM :32:02 AM :32:03 AM :32:04 AM :32:05 AM :32:06 AM :32:07 AM Averages -> Maximum -> 2.0
11 Thermal Cycle Number: 2 Date 11/8/2013 3:48:05 PM :48:06 PM :48:07 PM :48:08 PM :48:09 PM :48:10 PM :48:11 PM :48:12 PM :48:13 PM :48:14 PM :48:15 PM :48:16 PM :48:17 PM :48:18 PM :48:19 PM :48:20 PM :48:21 PM :48:22 PM :48:23 PM :48:24 PM :48:25 PM :48:26 PM :48:27 PM :48:28 PM :48:29 PM :48:30 PM :48:31 PM :48:32 PM :48:32 PM :48:33 PM :48:34 PM :48:35 PM :48:36 PM :48:37 PM :48:38 PM :48:39 PM :48:40 PM :48:41 PM :48:42 PM :48:43 PM :48:44 PM :48:45 PM :48:46 PM :48:47 PM :48:48 PM :48:49 PM :48:50 PM :48:51 PM :48:52 PM :48:53 PM :48:54 PM :48:55 PM :48:56 PM :48:57 PM :48:58 PM :48:59 PM :49:00 PM :49:01 PM :49:02 PM :49:03 PM Averages -> Maximum -> 7.9
12 Thermal Cycle Number: 3 Date 11/11/ :32:48 AM :32:49 AM :32:50 AM :32:51 AM :32:52 AM :32:53 AM :32:54 AM :32:55 AM :32:56 AM :32:57 AM :32:58 AM :32:59 AM :33:00 AM :33:01 AM :33:02 AM :33:03 AM :33:04 AM :33:05 AM :33:06 AM :33:07 AM :33:08 AM :33:09 AM :33:10 AM :33:11 AM :33:12 AM :33:13 AM :33:14 AM :33:15 AM :33:16 AM :33:17 AM :33:18 AM :33:19 AM :33:20 AM :33:21 AM :33:22 AM :33:23 AM :33:24 AM :33:25 AM :33:26 AM :33:27 AM :33:28 AM :33:29 AM :33:30 AM :33:31 AM :33:32 AM :33:33 AM :33:34 AM :33:35 AM :33:36 AM :33:37 AM :33:38 AM :33:38 AM :33:39 AM :33:40 AM :33:41 AM :33:42 AM :33:43 AM :33:44 AM :33:45 AM :33:46 AM Averages -> Maximum -> 6.9
13 Thermal Cycle Number: 3 Date 11/11/2013 3:24:43 PM :24:44 PM :24:45 PM :24:46 PM :24:47 PM :24:48 PM :24:49 PM :24:50 PM :24:51 PM :24:52 PM :24:53 PM :24:54 PM :24:55 PM :24:56 PM :24:57 PM :24:58 PM :24:59 PM :25:00 PM :25:01 PM :25:02 PM :25:03 PM :25:04 PM :25:05 PM :25:06 PM :25:07 PM :25:08 PM :25:09 PM :25:10 PM :25:11 PM :25:12 PM :25:13 PM :25:14 PM :25:15 PM :25:16 PM :25:17 PM :25:18 PM :25:19 PM :25:20 PM :25:21 PM :25:22 PM :25:23 PM :25:24 PM :25:25 PM :25:26 PM :25:26 PM :25:27 PM :25:28 PM :25:29 PM :25:30 PM :25:31 PM :25:32 PM :25:33 PM :25:34 PM :25:35 PM :25:36 PM :25:37 PM :25:38 PM :25:39 PM :25:40 PM :25:41 PM Averages -> Maximum -> 3.5
14 Thermal Cycle Number: 4 Date 11/12/ :24:16 AM :24:17 AM :24:18 AM :24:19 AM :24:20 AM :24:21 AM :24:22 AM :24:23 AM :24:24 AM :24:25 AM :24:26 AM :24:27 AM :24:28 AM :24:29 AM :24:30 AM :24:31 AM :24:32 AM :24:33 AM :24:34 AM :24:35 AM :24:36 AM :24:37 AM :24:38 AM :24:39 AM :24:40 AM :24:41 AM :24:42 AM :24:43 AM :24:44 AM :24:45 AM :24:46 AM :24:47 AM :24:48 AM :24:49 AM :24:50 AM :24:51 AM :24:52 AM :24:53 AM :24:54 AM :24:55 AM :24:56 AM :24:57 AM :24:58 AM :24:59 AM :25:00 AM :25:01 AM :25:02 AM :25:03 AM :25:04 AM :25:05 AM :25:06 AM :25:07 AM :25:08 AM :25:09 AM :25:10 AM :25:11 AM :25:12 AM :25:13 AM :25:14 AM :25:15 AM Averages -> Maximum -> 2.7
15 Thermal Cycle Number: 4 Date 11/12/2013 2:07:06 PM :07:07 PM :07:08 PM :07:09 PM :07:10 PM :07:11 PM :07:12 PM :07:13 PM :07:13 PM :07:14 PM :07:15 PM :07:16 PM :07:17 PM :07:18 PM :07:19 PM :07:20 PM :07:21 PM :07:22 PM :07:23 PM :07:24 PM :07:25 PM :07:26 PM :07:27 PM :07:28 PM :07:29 PM :07:30 PM :07:31 PM :07:32 PM :07:33 PM :07:34 PM :07:35 PM :07:36 PM :07:37 PM :07:38 PM :07:39 PM :07:40 PM :07:41 PM :07:42 PM :07:43 PM :07:44 PM :07:45 PM :07:46 PM :07:47 PM :07:48 PM :07:49 PM :07:50 PM :07:51 PM :07:52 PM :07:53 PM :07:54 PM :07:55 PM :07:56 PM :07:57 PM :07:58 PM :07:59 PM :08:00 PM :08:01 PM :08:02 PM :08:03 PM :08:04 PM Averages -> Maximum -> 6.4
16 Thermal Cycle Number: 5 Date 11/13/ :24:51 PM :24:52 PM :24:53 PM :24:54 PM :24:55 PM :24:56 PM :24:57 PM :24:58 PM :24:58 PM :24:59 PM :25:00 PM :25:01 PM :25:02 PM :25:03 PM :25:04 PM :25:05 PM :25:06 PM :25:07 PM :25:08 PM :25:09 PM :25:10 PM :25:11 PM :25:12 PM :25:13 PM :25:14 PM :25:15 PM :25:16 PM :25:17 PM :25:18 PM :25:19 PM :25:20 PM :25:21 PM :25:22 PM :25:23 PM :25:24 PM :25:25 PM :25:26 PM :25:27 PM :25:28 PM :25:29 PM :25:30 PM :25:31 PM :25:32 PM :25:33 PM :25:34 PM :25:35 PM :25:36 PM :25:37 PM :25:38 PM :25:39 PM :25:40 PM :25:41 PM :25:42 PM :25:43 PM :25:44 PM :25:45 PM :25:46 PM :25:47 PM :25:48 PM :25:49 PM Averages -> Maximum -> 13.3
Fire Test Report API Standard 6FA, Third Edition, April 1999 Specification for Fire Testing of Valves. Performed for. Valvtechnologies.
Fire Test Report API Standard 6FA, Third Edition, April 1999 Specification for Fire Testing of Valves Performed for Valvtechnologies www.valv.com 8 inch Class 1500 Trunnion Ball Valve Product Code: N8C1-JJ-XX-B080-005EM-P01
Fire Test Report ANSI/API Standard 607, 5 th Edition. ValvTechnologies, Inc.
Fire Test Report ANSI/API Standard 607, 5 th Edition Performed for ValvTechnologies, Inc. www.valv.com 2 inch Class 1500 Trunnion Ball Valve Valve Code: H8C2-JJ-FP-B020-004AA-P02 Project Number: 213204
Fire Test Report API Standard 607, 4th Edition
Fire Test Report API Standard 607, 4th Edition Performed for ValvTechnologies, Inc. www.valv.com 4 inch Class 300 Ball Valve Product Code: V5CC-RF-FP-B040-008ZZ Project Number: 210245 February 22, 2011
Fire Test Report ANSI/API Standard 607, 5th Edition. ValvTechnologies, Inc. 8 inch Class 300 Ball Valve
Fire Test Report ANSI/API Standard 607, 5th Edition Performed for ValvTechnologies, Inc. www.valv.com 8 inch Class 300 Ball Valve Product Code: H5C2-RF-FP-B080-004AA-P02 Project Number: 213204 Test Date:
ANSI/API Standard 607 Sixth Edition 2010 ISO 10497: 2010 Fire Test Certificate
ANSI/API Standard 607 Sixth Edition 2010 ISO 10497: 2010 Fire Test Certificate Name of Manufacturer: ValvTechnologies, Inc. Test Date: 10/26/2010 Designation of Valve: Ball Valve NexTech Series Report/Certificate
MP and MP Diaphragm and Seal Kits for MP8000 Series Actuators
MP8000-6325 and MP8000-6350 Diaphragm and Seal Kits for MP8000 Series Actuators Contents of the MP8000-6325 Diaphragm and Seal Kit for MP82 and MP83 Actuators One seal, 5/8 in. Internal Diameter (I.D.)
SETTING THE STANDARDS TO BE LEAK FREE
Emissions Reduction Technology Forum 12 th LDAR Symposium May 15-17, 2011 New Orleans, LA SETTING THE STANDARDS TO BE LEAK FREE GASKETS AND PACKINGS DESIGNED FOR A LEAK FREE OPERATION Standards Certification
Fugitive Emissions Standards & Laboratory Test Methods for Valves
Fugitive Emissions Standards & Laboratory Test Methods for Valves By: Greg Johnson President, United Valve 50 Years in 50 Seconds 1964 Houston air pollution Measuring air pollution in 1974 1 50 Years in
Bore (B) Pitch Diam. Drilling Template Flanges (1) Diam of Diam of. Groove. Neck D X G A Raised Face Raised Face P Raised face
Class 300 Orifice s Pipe size Thickness of Depth of jack Jack screw s (1) screw slot size & of and raised face Hub Bevel threaded Length of of Stud stud bolts Face face face bolt circle Bolts Bolts Bolt
Innovative World Leader
Innovative World Leader The ANSWER to Tight shut-off in various applications, Series 600 Triple offset butterfly valve is a virtual solution for heavy duty process, high pressure & temperature, and high
Description of Bolt Torque Tables
Maximum (preferred) torque required per bolt (foot pounds) to arrive at the maximum available / recommended gasket stress shown in the previous column. (4) Maximum gasket stress recommended or available
Integra Pneumatically Operated Valves
P/N 0-025696 REV. D 09/7 INSTRUCTION SHEET Integra Pneumatically Operated Valves ", 2-way, normally open, normally closed, sampling pneumatic designs; 4" 2-way, normally open, normally closed designs REPAIR
Excerpts from the ASME PVP 2017 technical paper
Excerpts from the ASME PVP 2016 technical paper An Improved Design of Threaded Closures for Screw-Plug Heat Exchangers by Haresh Sippy, MD, TEMA India Ltd Excerpts from the ASME PVP 2017 technical paper
SANITARY APPLICATIONS
SONDEX PLATE HEAT EXCHANGERS SANITARY APPLICATIONS SONDEX Fit earlier models Sonder Safe (safety plates) available Effective and glueless Sonder Lock or Sonder Snap gasket Available in all pressable materials
Internal Safety Shutoff & Operating Valve. Features. Internal Safety Shutoff & Operating Valve
The Shand & Jurs 96330 Internal Safety Shutoff and Operating Valve provides automatic, foolproof, quick acting shutoff of product flow in tanks and manifold lines. Extremely versatile, it can be mounted
1999 Honda Accord DX
Installation 1. Clean tensioner pulleys. Ensure cylinder No. 1 is at TDC by aligning dimple on timing belt drive pulley with pointer on oil pump housing. See Fig. 4. Ensure camshaft pulley TDC marks are
Fo ge Steel Floating Ball Valves
Fo ge Steel Floating Ball Valves 26 Design and Inspection Standard: Pressure-Temperature Ratings Shell Wall Thickness Face-to-face Dimensions End connection Dimensions Pressure Test Fire Safe Test Marking
RCM - Direct Reading Flowmeters
Compact Design Easy to Install Horizontal or Vertical Installation Flow Rates up to 3000 GPM (Liquid) or 20000 SCFM (Gas) Low Pressure Drop Optional Alarms and Output Signals Accuracy: ± 3% of full scale
Description of Bolt Torque Tables
Maximum (preferred) torque required per bolt (foot pounds) to arrive at the maximum available / recommended gasket stress shown in the previous column. (4) Maximum gasket stress recommended or available
INSTALLATION, OPERATION AND MAINTENANCE MANUAL
TYPE (BSA) SEALED VALVE BODY Series 2002 INSTALLATION, OPERATION AND MAINTENANCE MANUAL 1998-2013 by RF Valves, Inc. CUSTOMER SERVICE HOT-LINE 1-410-850-4404 Page 2 of 9 CONTENT 1.0 Introducing the airflex
IOM Manual. IOM Manual. Series 76/77.
IOM Manual IOM Manual Series 76/77 www.flowlinevalves.com Flow Line Valve and Controls, L.L.C. 110 Main Project Road Schriever, LA 70395 P.O. Box 677 Schriever, LA 70395 Phone 985-414-6004 * Toll Free
PVP Pressure Vessels & Piping Conference. Final Program. Pressure Vessel Technologies A Look Ahead into the Next Decade
PVP 2011 Final Program 2011 Pressure Vessels & Piping Conference Pressure Vessel Technologies A Look Ahead into the Next Decade July 17 21, 2011 Baltimore Marriott Waterfront Hotel Baltimore, Maryland,
I-VIC300MS. Vic -300 MasterSeal Butterfly Valves WARNING SERIES 761
warning Read and understand all instructions before attempting to install, remove, adjust, or perform maintenance on any Victaulic piping products. Depressurize and drain piping systems before attempting
Outstanding. Valve Stem Packings. Teadit 010-ELE (Extremely Low Emissions) Combo Set Valve Stem Packings for Extreme Emission Control
Outstanding Valve Stem Packings for Petroleum and Chemical Process Industry Teadit 010-ELE (Extremely Low Emissions) Combo Set Valve Stem Packings for Extreme Emission Control Teadit Style Packings for
Qualification Testing of Meritec High Power Conformal Connector 107 position, short (.22 inch stack height) and tall (.33 inch stack height) versions
Qualification Testing of Meritec High Power Conformal Connector 107 position, short (.22 inch stack height) and tall (.33 inch stack height) versions Project 1256 Scope: Test 1 per EIA-364-23 - determine
1 NRG #40 Anem. m/s 2 NRG #40 Anem. m/s 3 NRG #40 Anem. m/s 4 NRG #40 Anem. m/s 5 NRG #40 Anem. m/s 6 NRG #40 Anem. m/s. 30 m. 40 m. 30 m. m/s.
1 Site Information: Sensor Information: 1 2 3 4 6 7 #0P Wind Vane 8 #0P Wind Vane 9 NRG #1S Temp C BP- Barom. mb 11 No SCM Installed 12 No SCM Installed Summary Report Channel 1 2 3 4 6 7 8 9 Height 0
Rosemount 485 Annubar Pak-Lok Assembly
Quick Installation Guide 00825-0300-809, Rev EA Pak-Lok 85 Annubar Rosemount 85 Annubar Pak-Lok Assembly Start Step 1: Location and Orientation Step 2: Drill Holes into Pipe Step 3: Weld Mounting Hardware
Drive Axles SHAIS171. The Dana LMS Hub is available on the following Steer and Drive Axle Models:
Information Sheet Spicer Drive Axles SHAIS171 Topic: Dana LMS Hub Assembly Procedure Steer and Drive Axles Note: Bulletin ABIB-0302 replaces the original bulletin ABIB-9606. The Dana LMS hub design eliminates
Designing for Leak Free Operation
This file was downloaded from WWW.LDAR.COM 11 th LDAR Symposium May 18-19, 2011 New Orleans, LA Designing for Leak Free Operation The secret to reducing LDAR compliance costs! Standards Certification Education
SV SERIES. Metal Seated Ball Valves
SV SERIES Metal Seated Ball Valves 1/2 THRU 12 ANSI 150# THRU ANSI 1500# FULL PORT AND REDUCED PORT UNI-DIRECTIONAL AND BI-DIRECTIONAL 316SS OR CARBON STEEL BODY LIVE LOADED STEM PACKING HIGH QUALITY CASTINGS
B Series 1/2" to 2" 2-Way and 3-Way Bronze Control Valves
INSTALLATION AND MAINTENANCE INSTRUCTIONS IM-1-620-US November 2015 B Series 1/2" to 2" 2-Way and 3-Way Bronze Control Valves 1. Safety 2. Technical details 3. Installation and Commissioning 4. Maintenance
P445 Series Electronic Lube Oil Control
FANs 125, 121 s Section P Product/Technical Bulletin P445 Issue Date 0100 P445 Series Electronic Lube Oil The P445 Series Electronic Lube Oil is designed for use on refrigeration compressors equipped with
VCS/VCFS Prevent future leaks and blowouts
VCS/VCFS Prevent future leaks and blowouts InnovatIve engineering for corrosion protection For Zero Fugitive Emissions & Extreme Critical Sealing Applications The VCS/VCFS systems use proprietary materials
GF Piping Systems Flange Insulation
GF Piping Systems Flange Insulation 10014347_02/17 Disclaimer Information in the catalog GF Central Plastics is as diligent as possible in compiling and updating the information in its catalog. However,
REMOVAL & INSTALLATION
REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING & COUNTERBALANCE SHAFT BELTS
REMOVAL & INSTALLATION
REMOVAL & INSTALLATION TIMING BELT Removal 1. Disconnect negative battery cable. On Millenia, raise and support vehicle. Remove right front wheel. Remove lower engine covers. 2. On all models, remove accessory
CE43 1" (DN25) to 4" (DN100) Carbon Steel Cage Design, Two Port Control Valves
Globe 13 CE43 1" (DN25) to 4" (DN) Carbon Steel Cage Design, Two Port Description The CE43 series is a range of carbon steel two port, cage trim, control valves conforming to ANSI B16.34, ASME VIII standards
SECTION METERS AND GAGES FOR HVAC PIPING
PART 1 GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions Specification Sections, apply to this Section. 1.2 SUMMARY A. This
2018 Junior Sprint Rules
2018 KidSprint Engine Rules Briggs World Formula 2018B All parts must be Briggs & Stratton factory production parts unless otherwise noted in these rules. No machining, polishing or alteration of any parts
TEADIT PLANTS. Teadit International (Kufstein / Austria) Teadit North America (Houston / USA) Teadit Ind. e Com. (Rio de Janeiro / Brazil)
1 TEADIT PLANTS Teadit International (Kufstein / Austria) Teadit North America (Houston / USA) Teadit China (Shanghai) Teadit India (Mumbai) Teadit Argentina (Buenos Aires) Teadit Ind. e Com. (Rio de Janeiro
INSTALLATION, OPERATION AND MAINTENANCE MANUAL
INSTALLATION, OPERATION AND MAINTENANCE MANUAL LUDLOW SERIES FIGURE 340-S 3 to 14 Lever & Spring Swing Check Valves TABLE OF CONTENTS Introduction. 1 Description of Operation... 1 Receiving & Storage...
I-VIC300MS. Series 761 Vic-300 MasterSeal Carbon Steel Butterfly Valve Series 461 Vic-300 MasterSeal Stainless Steel Butterfly Valve WARNING
INSTALLATION AND MAINTENANCE INSTRUCTIONS I-VIC300MS Series 761 Vic-300 MasterSeal Carbon Steel Butterfly Valve Series 61 Vic-300 MasterSeal Stainless Steel Butterfly Valve SERIES 761 SERIES 61 Read and
High Temperature Chemical Process Inline Pumps
Bulletin C-1.2.21. Dean Pump Division High Temperature Chemical Process Inline Pumps Series DL Series DL High Temperature Chemical Process Inline Pumps Capacities to 6 GPM (182 m 3 /hr) Heads to feet (167
Dual Expanding Plug Valve MADE IN THE USA
Dual Expanding Plug Valve MADE IN THE USA WESTERN VALVE - DOUBLE BLOCK AND BLEED Facility Located in Bakersfield California Western Valve, Inc. was established in 1991. What started out as a valve repair
Fluid Pump. Special Tool(s) Alignment Gauge, Transmission Fluid Pump Alignment Gauge, Transmission Fluid Pump
SECTION 307-01: Automatic Transaxle/Transmission 5R55S 2009 Mustang Workshop Manual DISASSEMBLY AND ASSEMBLY OF SUBASSEMBLIES Procedure revision date: 06/30/2009 Fluid Pump Special Tool(s) Alignment Gauge,
2002 Chevrolet Blazer
The blower motor will operate in any switch position, as long as the ignition switch is in the RUN position and the mode switch is in any position other than OFF. When the ignition switch is on, power
SOLID CONSTRUCTION PTFE STEP FACE GASKETS FOR IMPROVED SEALING PERFORMANCE IN MONDI PIPING
SOLID CONSTRUCTION PTFE STEP FACE GASKETS FOR IMPROVED SEALING PERFORMANCE IN MONDI PIPING MIKE SHORTS, VP & GM TRIANGLE FLUID CONTROLS LTD. BELLEVILLE, ONTARIO, CANADA PHONE: 1-613-968-1100 MIKE@TRIANGLEFLUID.COM
PWH API 610 SINGLE STAGE OH2
API 6 SINGLE STAGE OH2 API 6 PROCESS PUMP HYDRAULIC PERFORMANCE COVERAGE Hz Performance Coverage Visit our web site at www.pumpworks6.com and specify flow and performance needs and obtain pump selection,
Safety Instructions. Series 3 E. for Installation, Operation and Maintenance of ABO Buteerfly Valves
Safety Instructions for Installation, Operation and Maintenance of ABO Buteerfly Valves Series 3 E 1 1. All safety instructions should be read carefully; otherwise all manufacturer's warranties become
PROVEN TECHNOLOGY. PROVEN PROBLEM SOLVER.
THE ONE CONSTANT IS CHANGE PROVEN TECHNOLOGY. PROVEN PROBLEM SOLVER. IT S MADE LIKE NO OTHER, SEALS LIKE NO OTHER, & PERFORMS 60% LONGER CHANGE, IT S SAFE. THE CHANGE GASKET. UNIQUELY MANUFACTURED. SHAPE
SPIRA-TROL 1/2" to 4" ANSI Two-port KEA, KFA and KLA Control Valves
1/2" to 4" ANSI Two-port KEA, KFA and KLA Description SPIRA-TROL is a range of two-port single seat globe valves with cage retained seats conforming to ASME/ANSI standards. These valves are available in
2005 Hyundai Tucson LX. On some models, engine is equipped with a timing belt and timing chain. Inspect timing chain when replacing timing belt.
TIMING BELT NOTE: On some models, engine is equipped with a timing belt and timing chain. Inspect timing chain when replacing timing belt. Removal 1. Remove the engine cover. See Fig. 1. 2. Remove right
PFA LINED BALL VALVES Installation, Operation and Maintenance Manual
ACRIS PFA LINED BALL VALVES WWW.AMRESIST.COM Table of Contents Safety Instructions - Definition of Terms............................................2 Introduction..............................................................2
Improving Valve Fugitive Emissions Performance
Improving Valve Fugitive Emissions Performance Steve McJones and Rich Sobilo March 6, 2014 Steve McJones Advisor Pressure Vessels, Piping and Valves BP Refining & Logistics Technology Support BP Refineries
ASME 350 BAR SAE 690 BAR
GENERAL HYDRAULIC PIPES 10-40 BAR SAE 50 BAR SAE 3000 PSI SAE 6000 PSI DIN 350-400 BAR SCHEDULE SERIE SAE 3000 PSI 1 SAE 6000 PSI ASME 350 BAR Product Page GS-ASME s 350 bar 203 SAE 690 bar - Grooving
EXTERNAL DISCONNECT ENCLOSURE INSTALL
The Intent and Purpose of the EXD Enclosure is to: 1) Isolate the primary power supply. 2) Initiate appropriate PPE for entry. 3) Prevent unauthorized entry, disconnect power before entry, and requiring
Profile Gaskets. Profile Gaskets with Covering Layers. Grooved Gaskets with Standard Profile. Grooved Gaskets with Convex Profile.
Gaskets with Covering Layers Grooved Gaskets with Standard Gaskets Grooved Gaskets with Convex CONVEX Gaskets EN ISO 900 Gaskets Gaskets Gasket Types Page 3 Construction Materials Page 3 Grooved Gaskets
DR Series Reactive Discharge Dampeners For Drilling
DR Series Reactive Discharge Dampeners For Drilling Instruction, Operating & Maintenance Manual Manufacturer of Pulsation Control Products 1.833.PPC.PROD 3309 Essex Dr. Suite 200, Richardson, Texas 75082
Patented S2 TM Stem Seal. Dual Body Seal. Fugitive Emissions Control.
Patented S TM Stem Seal s Dual Body Seal Fugitive Emissions Control Antistatic electrical continuity between ball, stem, and body. Locking washer Blowout proof stem. Live loaded packing assures reliable
SERIES 20FR16 FITTINGS GUIDE
ENGINEERED COMPOSITE PIPING SYSTEMS SERIES 20FR16 FITTINGS GUIDE FIBERBOND SERIES 20FR16 20FR16-C April 2016 Edition www.fiberbond.com www.futurepipe.com FIBERBOND Fittings Guide - Series 20FR16 and 20FR16-C
FLAT BIO END CAP TEST REPORT
FLAT BIO END CAP TEST REPORT Contents Page Section Heading/Title 3 1 Purpose 3 2 Background 3 3 Summary 3 4 Scope 3 5 References 3 6 Equipment and Materials 4/5 7 Results 6 8 Conclusions and Recommendations
Housing 3 GT/GTS Gas Turbine Meter
PL4802.2 Housing 3 GT/GTS Gas Turbine Meter 12 6 5 4 11 9 2 8 7 3 1 2 3 GT/GTS Gas Turbine Meter Housing Item No. Description Qty. Common To All Variations Part Numbers Product Variations 275 PSIG 1440
SPIRA-TROL 1/2" to 4" ANSI Two-port LEA, LFA and LLA Control Valves
1/2" to 4" ANSI Two-port LEA, LFA and LLA Description SPIRA-TROL is a range of two-port single seat globe valves with cage retained seats conforming to ASME/ANSI standards. These valves are available in
TED50XT EXTREME TEMPERATURE THERMALLY EFFICIENT, INSULATED BLADE DAMPER
3900 Dr. Greaves Rd. Kansas City, MO 64030 (816) 761-7476 FAX (816) 765-8955 APPLICATION Ruskin model TED50XT is a low leak, thermally efficient damper with insulated extruded aluminum blades specially
DISASSEMBLY AND ASSEMBLY (Continued)
205-03-23 Front Drive Axle/Differential Ford 8.8-Inch Ring Gear 205-03-23 49. Measure the ring gear backlash at four places to obtain a consistent reading. 1 Mount the special tools on the indicator base.
THE ONE CONSTANT IS CHANGE
THE ONE CONSTANT IS CHANGE 3.18 TYP OD= ID= Detail A A PROVEN TECHNOLOGY, PROVEN PROBLEM SOLVER. THE CHANGEGASKET. UNIQUELY MANUFACTURED. CHANGE HISTORY SHAPE > + 5X Thickness Change > 304-316L & Others
Expanding Plug Valve
Expanding Plug Valve Expanding Plug Valve Our expanding plug valve is designed for applications where positive shut-off, verifiable zero-leakage and double block and bleed (DBB) capabilities are required.
Fuel Injection System Low Pressure Leak Test Two-Filter Fuel System. Potential Fuel Leak Points Two-Filter. System
10 67-12 1 10 67-12 SUBJECT Fuel Injection System Low Pressure Leak Test, Potential Fuel Leak Points, Alternative Contrast Spray Method for Determining a Leak Path, Alternative Fuel Dye Method for Determining
Analyzing the Thermal Operating Conditions of a Solenoid
A CASE STUDY FROM SOLENOID SYSTEMS Analyzing the Thermal Operating Conditions of a Solenoid BACKGROUND When designing a Solenoid the operating temperature of the Coil must be taken into account when assessing
PWH API 610 SINGLE STAGE OH2
PWH API 610 SINGLE STAGE OH2 PWH API 610 PROCESS PUMP HYDRAULIC PERFORMANCE COVERAGE 60 Hz Performance Coverage Visit our web site at www.pumpworks610.com and specify flow and performance needs and obtain
2004 Dodge Pickup R1500 MIL ILLUMINATION DIAGNOSTIC TROUBLE CODES P0401, P0403, P0404, P0405, P0406 TECHNICAL SERVICE BULLETIN
TECHNICAL SERVICE BULLETIN Reference Number(s): 18-021-04, Date of Issue: May 4, 2004 GROUP: Vehicle Performance SUBJECT MIL Illumination Diagnostic Trouble Codes P0401, P0403, P0404, P0405, P0406 OVERVIEW
Pipeline Accessories. Rubber Steel gasket Type RSG Type RSG-V Type RFG 4 pipes
Pipeline Accessories Rubber Steel gasket Type RSG Type RSG-V Type RFG 4 pipes Flange Gaskets Type RSG 4 pipes Reg.Nr. NG-5113CQ0574 Trinkwasser KTW/W270 Product Information RSG 4 pipes Rubber-Steel-Flange-Gasket
Control Components Pty Ltd. PO Box 212 Caringbah NSW 1495 Sydney Australia ph: +61 (0) fx: +61 (0)
ABN 24 8 175 293 PO Box 212 Caringbah NSW 1495 Sydney Australia ph: +61 ()2 9542 8977 fx: +61 ()2 9542 7978 www.controlcomponents.com.au Magnetic Visual Level Indicators made in Australia under licence
1 of 25 9/12/2013 9:07 PM
1 of 25 9/12/2013 9:07 PM 46RE Automatic Transmission DISASSEMBLY 1. Clean exterior of transmission with suitable solvent or pressure washer. 2. Place transmission in vertical position. 3. Measure the
SOLUTIONS. Airless Spray System. In This Issue: Airless Spray System pg. 2. Improved FlowMaster pg. 5
THE LATEST PRODUCTS AND NEWS FOR LINCOLN CUSTOMERS SOLUTIONS DECEMBER 2002 VOL. 4, NO. 1 Airless Spray System In This Issue: Airless Spray System pg. 2 Improved FlowMaster pg. 5 MC 2 Progressive High Pressure
Miniature Proportional Valve Thermally Compensated Proportional Valve. Physical Properties
VSO Miniature Proportional Valve Thermally Compensated Proportional Valve Typical Applications Gas Chromatography Mass Spectrometry Ventilators O 2 Concentrators/Conservers Anaesthesia Delivery & Monitors
PRODUCT OVERVIEW. Our BDB (Bolted Body) and BW3 (Fully Welded Body) trunnion-mounted ball valves are designed and manufactured
PRODUCT OVERVIEW For over 30 years, FluoroSeal has been manufacturing and customizing a wide range of valves, and accessories for many industries including Oil & Gas, Petrochemical, Chemical, Mining, Pharmaceutical,
FISHBONE THE FUTURE OF HIGH PERFORMANCE SEALING HAS ARRIVED
AIGI ENVIRONMENTAL INC. THE FUTURE OF HIGH PERFORMANCE SEALING HAS ARRIVED Patented FISHBONE Uncompressed Compressed 1,000,000 times lower leakage than TA-LUFT Test limit 25 times lower leakage than Chevron
Gasket & Fastener Handbook. A Technical Guide To Gasketing & Bolted Flanges
Gasket & Fastener Handbook A Technical Guide To Gasketing & Bolted Flanges About Lamons Lamons is one of the largest gasket and bolt suppliers in the world, committed to quality and local service. We have
Fisher TBX Hydro Plug Fixture
Instruction Manual TBX Hydro-Plug Fixture Fisher TBX Hydro Plug Fixture Contents Introduction... 1 Scope of Manual... 1 Description... 2 Educational Services... 2 Principle of Operation... 2 Maintenance...
Installation, Operation and Maintenance Guide II NIBCO High Performance Butterfly Valves Series 6822 and 7822
Installation, Operation and Maintenance Guide II NIBCO High Performance Butterfly Valves Series 6822 and 7822 Statements: NIBCO High Performance Butterfly Valves, Series 6822 and 7822, have been designed
INSTALLATION, OPERATION AND MAINTENANCE MANUAL
INSTALLATION, OPERATION AND MAINTENANCE MANUAL LUDLOW SERIES FIGURE 350-W 3 to 24 Lever & Weight Air-Cushioned Swing Check Valves TABLE OF CONTENTS Introduction. 1 Description of Operation... 1 Receiving
LOWER MACUNGIE TOWNSHIP COMMUNITY CENTER ADDITIONS AND RENOVATIONS
LOWER MACUNGIE TOWNSHIP COMMUNITY CENTER. SECTION.0 - GENERAL-DUTY VALVES FOR PLUMBING PIPING PART - GENERAL. RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and
Provides the perfect seal, protects flanges, valves and pipelines against corrosion whilst improving safety and reducing the risk of fire.
Provides the perfect seal, protects flanges, valves and pipelines against corrosion whilst improving safety and reducing the risk of fire. s are typically used on offshore installations, sea water environments,
Generator/Starter Clutch
8-0 8. Generator/Starter Clutch Service Information 8-1 Shroud 8-2 A.C Generator 8-2 R.Crank Case Cover 8-4 Starter Clutch 8-6 Service Information General Safety This section describes the removal and
Series 240 Type 3351 Pneumatic On/off Valve
Series 240 Type 3351 Pneumatic On/off Valve Application Shut-off valve with tight shut-off for liquids, gases and vapors according to DIN or ANSI standards Valve size DN 15 to 100 NPS ½ to 4 Pressure rating
Max. Input Power (W) Input Current v 2 2 0v 2 40v. Enclosure
Output Power (W) Output Voltage (V) Output Current (A) Efficiency@ Max Load Max Case Temp. ( C) Input Current Max. Input Power (W) Inrush Current (Apk/50%-µs) THD @ Max Load (%) Power Factor @ Max Load
Bolting QA/QC Bulletin
Bolting QA/QC Bulletin M&TE Review 8-27-14 There have been several incidents over the past few months regarding torqueing methods, calibration procedures and verification of conversion charts matching
Integra Pneumatically Operated Distribution Valves
P/N 01-1007275 REV. D 10/17 INSTRUCTION SHEET Integra Pneumatically Operated Distribution Valves 3 4", high-temperature, 2-way, normally open, normally closed pneumatic designs REPAIR INSTRUCTIONS For
V550 Spring Lock Flanged Connection with Packing Gland
VERIS Verabar Flanged Models V550 Spring Lock Flanged Connection with Packing Gland The Most Accurate and Reliable Technology for Measuring Gas, Liquid and Steam Developed from aerospace technology, the
Dimensional Data Curb Optional Glass Damper Hood. A B C Size (O.D.) Size (O.D.) Qty Size Actuator Qty
Submittal Data Model PELV-100 Penthouse Elevator Vented Hood Application and Design The PELV-100 Penthouse Elevator Vented Hood is a gravity ventilator penthouse with an 18" x 18" gasketed access door
ULTRASONIC HEAT METER
MEASURE TODAY. ENSURE TOMORROW. tprime TM Series 280T Applications Residential submetering Commercial buildings District heating / cooling HVAC Green energy management AMR and Billing Features Wear-free.
Models FW, FWO & FWW 403 thru 1018
BULLETIN 2332 P-222-28 Installation Instructions Overrunning Clutch Couplings Models FW, FWO & FWW 403 thru 1018 23601 Hoover Road - Warren, MI 48089-3994 - 586-758-5000 www.formsprag.com Introduction
MODEL 5800 CONTENTS. Installation, Operation, and Maintenance Instructions 1.0 GENERAL
Installation, Operation, and Maintenance Instructions MODEL 5800 March 2002 CONTENTS 1.0 GENERAL 1.1 Model Number ----------------------------------------------------------------------------------------------
MK Series - High Performance Butterfly Valves Operation and Maintenance Instructions
COMMERCIAL Bray Controls Commercial Division 13788 West Road, Suite 200A Houston, Texas 77041 BCDSales@Bray.com Phone: 1-888-412-2729 Fax: 1-888-412-2720 www.braycommercialdivision.com MK Series - High
Series 11 Miniature Pneumatic Solenoid Valve 15mm Solenoid Valve
Series 11 Miniature Pneumatic Solenoid Valve 15mm Solenoid Valve Typical Applications Oxygen Conservers Oxygen Concentrators Compression Therapy Gas Chromatography Insufflators Medical & Analytical Gas
Ball Valves in cast 316 SS multi-port, bolted construction
65 Ball Valves in cast 36 SS, bolted construction Type 65 can be combined with 800 PSI WOG Thread, socket and butt weld ends Full port to Sch 40 pipe 3/4/5 ports in L, X, T or I pattern Range of seal options
The World s First Flameless Crude Heater
AFRC 2013 Industrial Combustion Symposium Kauai, HI September 23-25, 2013 The World s First Flameless Crude Heater Great Southern Flameless, LLC Presented by Great Southern Flameless, LLC GSF One of the
GBV-G Balancing Valves
Ductile Iron ASTM A6, Grade 6-4-2 The Series GBV is a multi-turn, Y-style globe valve designed for accurate determination and control of fluid flow to circuits requiring precise balancing. Max. Working
COVER EQUIPMENT. VAREC BIOGAS 400W Series EMERGENCY RELIEF MANHOLE COVERS
COVER EQUIPMENT VAREC BIOGAS 400W Series EMERGENCY RELIEF MANHOLE COVERS The 400W Series is designed to provide emergency pressure and/or vacuum relief in storage tanks and vessels. Introduction The Varec