DOUBLE ROLLER COTTON GINNING MACHINE: ITS DRAWBACKS AND POSSIBLE MODIFICATIONS
|
|
- Estella Nelson
- 6 years ago
- Views:
Transcription
1 DOUBLE ROLLER COTTON GINNING MACHINE: ITS DRAWBACKS AND POSSIBLE MODIFICATIONS P.G. Patil Central Institute for Research on Cotton Technology (ICAR), Nagpur, (India) P.M. Padole Dept. of Mech. Engg., Visvesvaraya National Institute of Technology, Nagpur (India) ABSTRACT Detail design study revealed that present Double Roller (DR) Gin carries several drawbacks. In order to remove these drawbacks two conceptual modified models of DR gin were designed using Pro/ENGINEER software. Best design of modified DR gin found to be simple in operation, energy efficient, requires minimum operational cost, and consumes less spares. Saving in space requirement of the machine is observed to be 54 %. This modified design minimized lubricating points and application of grease. This design facilitates precise control over roller pressure. Machine manufacturing is very easy. This machine is very sturdy and operator friendly. INTRODUCTION Textiles constitute an important component of India s economy. Ginning is the first and most important mechanical process by which seed cotton is separated into lint (fibre) and seed and machine used for this separation is called as gin. There are mainly two types of gins (i) roller gins- most commonly used in India, Egypt, Uganda, Tanzania etc. and (ii) saw gins- extensively used in countries like USA, China, Australia, Uzbekistan etc.. Both type of gins are noted for certain advantages and disadvantages. The roller gin is used on high quality, fine fibred, extra-long staple cottons because of its tendencies to maintain fibre length and low nep levels as opposed to the adverse effects on these characteristics by the saw gins. Double roller (DR) gins are commonly used in rural India for ginning and producing about 2.8 million tonnes of lint [1]. In India about DR gins are working in around 4000 ginning factories and there is demand of around 1500 DR gins every year towards new addition as well as replacement of old one. During
2 1700 s some developments using roller principle followed and in 1840 Fones McCarthy invented single roller gin [2]. The British Middletone model of DR gin used 40 inches (1016mm) roller length while the American Foss model DR gin used 60 inches (1524mm) long roller [2]. Britishers introduced Middleton Double Roller gin manufactured by Platt Saco Lowell (UK) Ltd and Monforts M. Gladbach (Volkart) DR gin in India in the beginning of 20th Century. After India s independence Indian manufacturers have started manufacturing DR gins similar to Middletone DR gin and Monforts DR gin and major technological design modifications were not implemented for the improvement of the machine. PRESENT DESIGN AND WORKING PRINCIPLE OF DOUBLE ROLLER GIN It consists of two spirally grooved leather roller pressed against a fixed knife, are made to rotate at about rpm. Two moving blades combined with seed grids constitutes a central assembly known as beater which oscillates by means of a crank or eccentric shaft, close to the fixed knife. When the seed cotton is fed to the machine in action, fibres adhere to the rough surface of the roller are carried in between the fixed knife and roller in such a way that the fibres are partially gripped between them. The oscillating knife beats the seed and separates the fibres. This process is repeated for number of times and due to push-pull-hit action the fibres are separated from the seed, carried forward on the roller and dropped out of machine. The ginned seeds drop down through the grid which is oscillating along with beater. Drawbacks in Present Design of DR Gin Detail design study revealed that present DR gin carries several drawbacks. One of the most important drawbacks is complicated power transmission system. It includes six planetary gears which not only oscillates beater at 960 oscillations per minute but also rotate the rollers at 95 rpm as shown in Fig. 1. Nineteen teeth gear is fitted on main shaft, which transmits the motion to the gear having 89 teeth so that it rotates with 205 rpm. Gear with 46 teeth is fitted on the same shaft on which gear with 89 teeth is fitted. This gear (with 46 teeth) is transmitting motion to helical gear having 99 teeth which rotates the leather roller (left hand side) at 95 rpm and in clockwise direction. To rotate right hand side roller, the drive is taken from matching gear having 46 teeth so that direction is changed i.e. (anticlockwise) and this gear then transmitting motion to helical gear having 99 teeth which rotates the leather roller (right hand side) at 95 rpm. This system requires about 20 kg grease or 18 litre lubricating oil per machine per season. This grease/oil due
3 to leakage fall on the floor surface, and damages the lint quality, which is considered as serious contamination worldwide. Fig. 1 Conventional Double Roller Gin In present design, 21 bearings of different sizes and types are used which makes the maintenance complicated and costly. Also lubrication points are more i.e. 18 in number (Swing lever 8 points, hub 1 point, wrist pin 1 point, gear side pipe 2 points, weight lever 4 points, beater shaft 2 points). Uniform pressure between fixed knife and roller plays an important role in quality and out put of the lint. In present design the roller is pressed against fixed knife with the help of hanging dead weights (total weight of 1158 N i.e. 324 N and 255 N/roller on gear box side and offside respectively) mounted on the weight lever of 495 mm in length. This method does not ensure uniform pressure between roller and fixed knife, occupies more space, and also makes it difficult to remove the roller for maintenance. Presently rollers are made of chrome composite leather washers and wear rate of roller is 0.02 mm/h of working (i.e. it has life of around 1200 working hours). Besides this in rainy season it has tendency to absorb water and get swelled to reduce the life of material further. Studies revealed that chromium particles generated during the process of ginning produce deleterious effect on the people working in the vicinity [3]. Theoretically energy required to remove 1 kg lint (fibres) varies between 1075 to 2775 joules but actual energy consumed by present DR is about joules/kg lint. This is about 60 to 120 times more. This poor energy utilization efficiency is mainly due to improper design of gearbox, unscientific way of applying pressure etc. Machine noise level is reasonably high (93 db) due to the reciprocating action of beater and gearbox. Noise levels of 85 db and above have shown to cause hearing impairment after prolonged
4 exposure [4]. Study conducted on commercial ginning factory for past three years revealed that spare parts repairs and replacements and maintenance cost including grease/oil per season was found to be around 25 % of the initial cost (Rs ) of the machine because of drawbacks mentioned as above. POSSIBLE CONCEPTUAL DESIGN MODIFICATIONS AND EXPECTED IMPROVEMENTS In order to remove drawbacks mentioned above, two conceptual modified models of DR Gins were designed using Pro/ENGINEER software and after detailed analysis, better design is used for actual fabrication. First Conceptual Design In first proposed conceptual design, arrangement of separate electric motors 1 hp each is provided to rotate both the roller. Two shaft mounted speed reducers are attached to both the leather rollers separately (Fig. 2). Fig. 2 First Conceptual Design Power transmission from motor to shaft mounted speed reducer is achieved by pulley and V-belt arrangement. Separate electric motor of 1 hp is used for beater movement. Crankshaft with eccentric is used to convert rotatory motion of shaft into reciprocating
5 motion of beater shaft through oscillating head. The hanging weights used for applying pressure on roller against fixed knife are eliminated by providing push-pull and locking mechanism and attached to mainframe which is used to increase or decrease the roller pressure on the fixed knife. Split Coupling is provided for removing the roller for routine grooving and maintenance. The nut and screw mechanism to adjust the beater in respect of fixed knife is provided from the top of the side frames. Second Conceptual Design Second proposed conceptual design includes crankshaft with eccentric driven by electric motor, and flywheel with pulley & V-belt arrangement is provided to transmit power from electric motor to eccentric (Fig. 3) [5]. Power is supplied by 3 hp, 1440 rpm, 3 phase AC electric motor, which drives the main shaft at 960 rpm. This reduction in Fig. 3 Power transmission from electric motor to main shaft Fig. 4 Arrangement for change in direction and power transmission to roller speed is achieved through a V-belt drive having a reduction of 1: 1.5. Reciprocating motion of beater (960 oscillations per minute) is obtained by using eccentric mounted directly on main shaft and other end of connecting rod is connected to beater shaft through oscillating head. Left hand side roller is rotated at 120 rpm in clockwise direction by a set of combination of timer or V-belt-Pulley arrangement in which drive is directly taken from main shaft. The reduction of speed from 960 rpm to120 rpm is achieved in
6 two stages. First stage reduction is through a V-belt drive having a reduction of 1: 4 and second stage reduction is through timer belt drive with a speed reduction of 1:2 (Fig. 4). Idler is provided to timer/ V-belt to adjust the appropriate belt tension. Rpm of roller can be changed with change of pulley attached to roller shaft. Twenty degree full depth spur gear is mounted on main shaft. Number of teeth on gear is 60 [6]. The right hand side roller is rotated in opposite direction (i.e. in anticlockwise direction) to that of the left hand side roller. This change in direction is achieved by using identical matching gear to the gear fixed on main shaft so that rpm of both the rollers will remain same. With this simple arrangement total planetary gearbox arrangement present in existing design is eliminated. This will also avoid the use of grease/oil and reduce the repairs and maintenance cost. Due to this modified design the number of bearing required shall be reduced from 21 to 18 only. The number of lubricating points shall also be reduced considerably. The hanging weights used for applying pressure on roller against fixed knife are eliminated in present design by using spring loaded mechanism attached to main frame. Simple mechanism is designed for removing the roller for routine grooving and maintenance. This system is more scientific way of applying pressure uniformly and precisely on the roller and leads to more even wear-profile for rollers. The alternate appropriate material for roller has been selected out of several materials tried in laboratory. Results of composition covering has so for given encouraging results as regard to quality and productivity of lint. The appropriate arrangement to the machine is designed to check the dust emitted during the process of ginning by way of providing proper dust arresters. Detail analysis on Pro/ENGINEER showed that this conceptual design found to be better, hence machine is fabricated. Complete gearbox design and fabricated machine is shown in Fig. 5. Fig. 5 Second Conceptual Design
7 PERFORMANCE EVALUATION Performance of the machines was evaluated by ginning long staple Indian seed cotton variety named Surabhi having moisture content of 8.5 %. The ginning output of the second DR machine was found to 74 kg lint/h and fibre properties of lint viz. 2.5 % SL, UR, Mic, and Bt measured by High Volume Instrument (Uster 900) was observed to be 32.1 mm, 46 %, 3.4, 25 g/tex respectively. These results show that there was no damage to fibre properties of lint ginned on this machine. Electric power requirement of conceptual design is lower than the conventional machine. Electric current drawn during full load was found to be 5.3 A as against 8.63 A for conventional DR machine. This modified machine also requires less starting current of 14 A as against 25 A for conventional DR machine. CONCLUSIONS 1. The modified DR gin is simple in operation. 2. Machine manufacturing is very easy therefore cost of manufacturing is less. 3. This machine requires 30 % less energy than conventional DR. 4. Saving in space requirement of this machine is 54 %. 5. Lubricating points are less and grease is not required in the gearbox. 6. This machine facilitates precise control over roller pressure. 7. Machine requires less spares and therefore operational cost is minimum. 8. Cotton Quality is preserved during ginning operation. 9. This machine is very sturdy and operator friendly. NOMENCLATURE A- Ampere; Bt- Bundle Tenacity, Maximum specific stress to rupture the fibres in g/tex; Mic Fineness of fibre in Micronaire; SL- Span length, mm; UR- Uniformity Ratio in percentage. REFERENCES 1. International Cotton Advisory Committee Report, Washington DC, Bennet, C.A., Roller cotton ginning developments. Texas Cotton Ginners Association, Dallas, TX, 90, Iyer, G. V., Environmental and Health effects of rollers used in Ginning Industries, Journal of the Textile Association (July-Aug) 87-94, 1998.
8 4. Cooper, W. A., The ear hearing, loudness, and hearing damage. In M. J. Crocker, ed., Reduction of Machinery Noise, Purdue University, West Lafeyette, In., 43-50, Khurmi, R.S., and Gupta, J.K., A Textbook of Machine Design, 13th ed., Eurasia Publishing House, N. Delhi, Shigley, J.E., and Mischke, C.R., Mechanical Engineering Design, 5th ed., McGraw-Hill, New York, 1989.
2176 Improving Lint Quality using Modified Double Roller Gins in India
TITLE: DISCIPLINE: AUTHORS: 2176 Improving Lint Quality using Modified Double Roller Gins in India Engineering & Ginning P. G. Patil (Corresponding Author) Central Institute for Research on Cotton Technology,
More informationGEARBOX DESIGN FOR CNC LATHE
GEARBOX DESIGN FOR CNC LATHE Prof. Reji Mathew 1, Linto P Anto 2, Adith Shajan 3, Basil P Thomas 4, Elisa Manoj 5, Kuriakose M Renji 6 1Professor, Department of Mechanical Engineering, Mar Athanasius College
More informationDesign & Modeling of Mobile Chaff Cutter a Review
Design & Modeling of Mobile Chaff Cutter a Review Vishrut Raut 1, Prof.S.M.Fulmali 2 1 Student, Mtech CAD/CAM, B.D.C.E, vishrut.raut55@gmail.com 2 Assistant professor, Mechanical Engineering, B.D.C.E,
More informationNPTEL. Mechanics of Textile Machinery - Web course. Textile Engineering. COURSE OUTLINE. Machine elements and drives
NPTEL Syllabus Mechanics of Textile Machinery - Web course COURSE OUTLINE Machine elements and drives Introduction to drives, selection of drives, primary machine elements, special purpose drives and devices
More informationDesign, Construction and Testing of an Electric Powered Toggle Jack Mechanism
Design, Construction and Testing of an Electric Powered Toggle Jack Mechanism Ipilakyaa T.D. 1, Achirgbenda V.T. 2, Gbashi S. 3 1Department of Mechanical Engineering, University of Agriculture Makurdi,
More informationKeywords: Von Mises, Piston, Thermal Analysis, Pressure, CATIAV5R20, ANSYS14 I. INTRODUCTION
Finite Element Analysis of IC Engine Piston Using Thermo Mechanical Approach 1 S.Sathishkumar, Dr.M.Kannan and 3 V.Raguraman, 1 PG Scholar, Professor, 3 Assistant professor, 1,,3 Department of Mechanical
More informationAt the end of this lesson, the students should be able to understand:
Instructional Objectives: At the end of this lesson, the students should be able to understand: About rolling contact bearings Ball bearing and roller bearing Basics definitions of design parameters of
More informationConceptual design of planetary gearbox system for constant generator speed in hydro power plant
Conceptual design of planetary gearbox system for constant generator speed in hydro power plant Bhargav 1, M. A. Parameshwaran 2, Sivaraj S. 2 and Nithin Venkataram 1*, 1 Dept. of Mechanical and Manufacturing
More informationDesign and Fabrication of Eco Friendly Pedal Operated Lawn Mower for Agricultural Applications
IOSR Journal of Engineering (IOSRJEN) ISSN (e): 2250-3021, ISSN (p): 2278-8719 Vol. 08, Issue 6 (June. 2018), V (V) PP 12-17 www.iosrjen.org Design and Fabrication of Eco Friendly Pedal Operated Lawn Mower
More informationA Modified Version of Reciprocating Engine with Fuel Free Electromagnetic in Conventional Internal Combustion Engines
A Modified Version of Reciprocating Engine with Fuel Free Electromagnetic in Conventional Internal Combustion Engines V.Kumar*1 Assistant Professor (Sr.G) A.Sengolerayan *1 Assistant Professor (S.G) Dr.
More informationDesign and Analysis of Clutch Plate for Automatic Single Plate Clutch
ISSN 2395-1621 Design and Analysis of Clutch Plate for Automatic Single Plate Clutch #1 Ravikiran M. Tate, #2 S. H. Sarje 1 rtate26@gmail.com 2 suhas_sarje7@rediffmail.com #12 Mechanical Department, JSPM
More informationHOMER OPTIMIZATION BASED SOLAR WIND HYBRID SYSTEM 1 Supriya A. Barge, 2 Prof. D.B. Pawar,
1 HOMER OPTIMIZATION BASED SOLAR WIND HYBRID SYSTEM 1 Supriya A. Barge, 2 Prof. D.B. Pawar, 1,2 E&TC Dept. TSSM s Bhivrabai Sawant College of Engg. & Research, Pune, Maharashtra, India. 1 priyaabarge1711@gmail.com,
More informationDESIGN AND MANUFACTURING ELECTRICAL CAR JACK D.C. 12 VOLT
International Journal of Mechanical Engineering and Technology (IJMET) Volume 8, Issue 6, June 207, pp. 200 206, Article ID: IJMET_08_06_02 Available online at http://www.ia aeme.com/ijmet/issues.asp?jtype=ijmet&vtyp
More informationGEAR NOISE REDUCTION BY NEW APPROACHES IN GEAR FINISHING PROCESSES
GEAR NOISE REDUCTION BY NEW APPROACHES IN GEAR FINISHING PROCESSES Nikam Akshay 1, Patil Shubham 2, Pathak Mayur 3, Pattewar Vitthal 4, Rawanpalle Mangesh 5 1,2,3,4,5 Department of Mechanical Engineering,
More informationSTUDY AND ANALYSIS OF TIRE CHANGING MACHINE COMPONENTS
STUDY AND ANALYSIS OF TIRE CHANGING MACHINE COMPONENTS Mr. Sutar Gururaj 1,Mr. Suryawanshi Bhairavnath 2, Mr. Tengle Kiran 3 Mr. Thaware Madan 4 1,2,3,4UG, Mechanical Engineering, UCOER, Pune, Maharashtra,
More informationFRICTION DEVICES: DYNAMOMETER. Presented by: RONAK D. SONI Assistant Professor Parul Institute of Technology, Parul University
FRICTION DEVICES: DYNAMOMETER Presented by: RONAK D. SONI Assistant Professor Parul Institute of Technology, Parul University DYNAMOMETER A dynamometer is a brake but in addition it has a device to measure
More informationDHANALAKSHMI COLLEGE OF ENGINEERING
DHANALAKSHMI COLLEGE OF ENGINEERING (Dr.VPR Nagar, Manimangalam, Tambaram) Chennai - 601 301 DEPARTMENT OF MECHANICAL ENGINEERING III YEAR MECHANICAL - VI SEMESTER ME 6601 DESIGN OF TRANSMISSION SYSTEMS
More informationTechnical Bulletin. Drive Failure due to Incorrect Tensioner set-up. Transmission : Various Fuel : Petrol. Technical Details
Bulletin No. : TB0025 Issue Date : Oct 2013 Pages : 7 Subject : Drive Failure due to Incorrect Tensioner set-up Part No. : QBK538 / QTB578 Description : Timing Belt Kit Make : Mitsubishi / Volvo Engine
More informationINVESTIGATION ON THREE-WAY DUMPING MECHANISM OF A TWO- WHEEL TRACTOR TROLLEY
110 INVESTIGATION ON THREE-WAY DUMPING MECHANISM OF A TWO- WHEEL TRACTOR TROLLEY 1 *Shingade Mahesh, 2 Vamsi Krishna K, 3 Ajay Kumar Yadav * 1 & 3 (PG Scholar, Mechanical Engineering Department, National
More informationDesign and Fabrication of Palm Fronds Petioles Stripping Machine
Journal of Emerging Trends in Engineering and Applied Sciences (JETEAS) 6(4): 236-241 Scholarlink Research Institute Journals, 2015 (ISSN: 2141-7016) jeteas.scholarlinkresearch.com Journal of Emerging
More informationDesign and Analysis of Bent Pin Mechanism
Design and Analysis of Bent Pin Mechanism 1 Mr.Sachin R. Jaiswal, 2 Prof.D.M.Mate, 3 Dr. C.N.Sakhale 1 Assistant Professor, 2 Assistant Professor, 3 Associate Professor 1 Mechanical Engineering Department
More informationPOWER GENERATION BY MULTIPLE ROAD HUMPS
POWER GENERATION BY MULTIPLE ROAD HUMPS Asst Prof.Vaibhav Deshpande 1, Dr. H.K Amarnath 2, Abhishek Sutar 3, Sachin Hosalli 4, Manjunath Garagad 5, Prasad Undre 6. 1Asst. Professor, Dept Of Mechanical
More informationAQA GCSE Design and Technology 8552
AQA GCSE Design and Technology 8552 Mechanical devices Unit 2 Energy, materials, systems and devices 8 Objectives Be able to recognise and identify a range of movements Understand the functions of mechanical
More informationAnalysis of Multistage Linkage Based Eclipse Gearbox for Wind Mill Applications
Analysis of Multistage Linkage Based Eclipse Gearbox for Wind Mill Applications 1 Shrutika Patil, 2 J. G. Patil, 3 R. Y. Patil 1 M.E. Student, 2 Associate Professor, 3 Head of Department, Department of
More informationSCRAP COLLECTING VEHICLE
SCRAP COLLECTING VEHICLE Sunil Rathava 1, Gaurang Raval 2, Akshay Solanki 3, Shambhu Rai 4 1 Student, mechanical, V.I.E.R., Gujarat, INDIA 2 Student, mechanical, V.I.E.R., Gujarat, INDIA 3 Student, mechanical,
More informationAUTOMATION OF WINDSHIELD WIPER (Electrically controlled using LCC circuit)
AUTOMATION OF WINDSHIELD WIPER (Electrically controlled using LCC circuit) 1 M.SARAVANAN 2 G.SANDOSH KUMAR, 3 SALMAN.K.A.A, 4 S.RAVI SHANKAR. 5 M.PRAKASH, 6 S.SATHYAMOORTHI, 1,2,3,4, UG SCHOLAR Department
More informationDriver Driven. InputSpeed. Gears
Gears Gears are toothed wheels designed to transmit rotary motion and power from one part of a mechanism to another. They are fitted to shafts with special devices called keys (or splines) that ensure
More informationCHAPTER 6 GEARS CHAPTER LEARNING OBJECTIVES
CHAPTER 6 GEARS CHAPTER LEARNING OBJECTIVES Upon completion of this chapter, you should be able to do the following: Compare the types of gears and their advantages. Did you ever take a clock apart to
More informationStandard Test Method for Dropping Point of Lubricating Grease 1
Designation: D 566 02 An American National Standard British Standard 2877 Designation: 132/96 Standard Test Method for Dropping Point of Lubricating Grease 1 This standard is issued under the fixed designation
More information2003 Saturn Vue. SATURN 3.0L V6 DOHC - L-Series After VIN & Vue
TIMING BELT Removal 1. Disconnect negative battery cable. Remove air cleaner assembly. 2. Raise and support vehicle. Remove right front wheel. Remove lower front splash shield. 3. Lower vehicle. Loosen,
More informationANALYSIS OF EXISTING TROLLEY AXLE USING ANSYS
International Journal of Science, Environment and Technology, Vol. 4, No 2, 2015, 293 299 ISSN 2278-3687 (O) 2277-663X (P) ANALYSIS OF EXISTING TROLLEY AXLE USING ANSYS 1 Mr. Harish V. Katore, 2 Mr. Ashitosh
More informationTitle Objective Scope LITERATURE REVIEW
Title Objective Scope : Car Gear System : Investigate the force conversion in the gear system : Low rev engine match with five speed manual transmission Low rev engine match with four speed-auto transmission
More informationChapter B-3. Chapter 3. Actuators and output devices. Festo Didactic TP101
155 Chapter 3 Actuators and output devices Festo Didactic TP101 156 An actuator is an output device for the conversion of supply energy into useful work. The output signal is controlled by the control
More informationDesign and Fabrication of Automated Hacksaw Machine
Design and Fabrication of Automated Hacksaw Machine D.V.Sabariananda 1, V.Siddhartha 1, B.Sushil Krishnana 1, T.Mohanraj 2 UG Student [Mechatronics], Dept. of Mechatronics Engineering, Kongu Engineering
More informationReview of Overhead Crane and Analysis of Components Depending on Span
Review of Overhead Crane and Analysis of Components Depending on Span Omkar K. Sakurikar 1, D.V. Kushare 2 1Student, Department of Mechanical Engineering, N.D.M.V.P.S K.B.T. College of Engineering, Nashik,
More informationOptimization of Seat Displacement and Settling Time of Quarter Car Model Vehicle Dynamic System Subjected to Speed Bump
Research Article International Journal of Current Engineering and Technology E-ISSN 2277 4106, P-ISSN 2347-5161 2014 INPRESSCO, All Rights Reserved Available at http://inpressco.com/category/ijcet Optimization
More informationInstallation Tensioning Procedure
Contents PARTICULARS Introduction PIX X treme HTD Belts Construction Features Designation Pitch range Length range Pulley Dimensions Length tolerances Width tolerances PIX X treme Classical Belts Construction
More informationREVIEW ON NOISE AND VIBRATION IN AUTOMOBILES
REVIEW ON NOISE AND VIBRATION IN AUTOMOBILES AZAR R. INAMDAR 1, PRANITA A. DESHPANDE 2, SWAPNALI R. GADEKAR 3 1,2,3 Department of Mechanical Engineering, Sandip Foundation s, Sandip Institute of Technology
More informationDesign and Manufacturing of Indexing Fixture For Piston Compressor Block
Design and Manufacturing of Indexing Fixture For Piston Compressor Block Prof. G.E. Kondhalkar 1, Ganesh Kale 2, Aditya Kamble 3, Kunal Kshirsagar 4, Sarang Upasani 5 1 HOD Mechanical Dept, Anantrao Pawar
More informationAnalysis of Eclipse Drive Train for Wind Turbine Transmission System
ISSN 2395-1621 Analysis of Eclipse Drive Train for Wind Turbine Transmission System #1 P.A. Katre, #2 S.G. Ganiger 1 pankaj12345katre@gmail.com 2 somu.ganiger@gmail.com #1 Department of Mechanical Engineering,
More informationDesign and Analysis of Spring-Ball Clutch Torque Limiter
Design and Analysis of Spring-Ball Clutch Torque Limiter Nasiket M. Gawas, Manali S. Patkar, Prasad B. Gawade 1 B.E Student, B.E Student, 3 B.E Student Mechanical Engineering, Finolex Academy of Management
More informationKINEMATICS OF MACHINARY UBMC302 QUESTION BANK UNIT-I BASICS OF MECHANISMS PART-A
KINEMATICS OF MACHINARY UBMC302 QUESTION BANK UNIT-I BASICS OF MECHANISMS PART-A 1. Define the term Kinematic link. 2. Classify kinematic links. 3. What is Mechanism? 4. Define the terms Kinematic pair.
More informationDesign and Fabrication of Mini Saw Cotton Ginning Machine
IJIRST International Journal for Innovative Research in Science & Technology Volume 3 Issue 03 August 2016 ISSN (online): 2349-6010 Design and Fabrication of Mini Saw Cotton Ginning Machine Bhushan S.
More informationAUTOMATIC PNEUMATIC BUMPER IN 4 WHEELER VEHICLE
AUTOMATIC PNEUMATIC BUMPER IN 4 WHEELER VEHICLE Asst. Prof. Swapnil Patil,Suraj Mohite 2, Mahesh Motkar 3, Omkar Kurlekar 4, Krushna Raut 5 1,2,3,4,5 Mechanical Engineering, SPPU, Pune, (India) ABSTRACT
More informationPassive Vibration Reduction with Silicone Springs and Dynamic Absorber
Available online at www.sciencedirect.com Physics Procedia 19 (2011 ) 431 435 International Conference on Optics in Precision Engineering and Nanotechnology 2011 Passive Vibration Reduction with Silicone
More informationGatesFacts Technical Information Library Gates Compass Power Transmission CD-ROM version 1.2 The Gates Rubber Company Denver, Colorado USA
Gary L. Miller Plant Engineering November 7, 1991 DIFFERENCES IN SYNCHRONOUS BELTS All toothed belts are not the same; subtle differences in tooth profiles and construction affect performance. Synchronous
More informationTheory of Machines II EngM323 Laboratory User's manual Version I
Theory of Machines II EngM323 Laboratory User's manual Version I Table of Contents Experiment /Test No.(1)... 2 Experiment /Test No.(2)... 6 Experiment /Test No.(3)... 12 EngM323 Theory of Machines II
More informationDESIGN AND FABRICATION OF MULTIROD BENDING MACHINE
DESIGN AND FABRICATION OF MULTIROD BENDING MACHINE C. Anbumeenakshi 1, M.R.Thansekhar 2, Thanamani.M 3, Santhoshkumar.R 4, Parivallal.S 5, Senthilkumar.K 6 1 Assistant Professor, 2 Professor, 3,4,5,6 UG
More informationSHAFT MOUNTED HELICAL GEAR REDUCER
Shaft Mounted Helical Gear Assembly INTRODUCTION The VIGNESSH Shaft Mounted Helical Gear Units are the result of experience in design and production, taking advantage of the most recent relevent research
More informationOverhead Lines for Transmission and Distribution of Power System and its Consequences in Nigeria
IDOSR PUBLICATIONS International Digital Organization for Scientific Research ISSN:2550-794X Overhead Lines for Transmission and Distribution of Power System and its Consequences in Nigeria 1 Nweke F.
More informationDesign and Fabrication of Two Axis Pneumatic Arm
Design and Fabrication of Two Axis Pneumatic Arm Tapobrat Pani 1, Shubham Warate 2, Ritesh Chandrakar 3, Vaibhav Adulkar 4, Akshay Pawnarkar 5, Lecturer G.D.Gosavi 6 12345UG student at DBACER, Nagpur,
More informationTHREE AXIS PNEUMATIC TRAILER
THREE AXIS PNEUMATIC TRAILER Patel Umang M. 1, Patel Shailesh H. 2, Patel Sandip J. 3, Mr. Rahul M Desai. 4 1. Student of Mechanical Engineering at Samarth College Of Engineering And Technology Himatnagar,
More informationAn Approach for Power Generation with Reduced Fuel Consumption using PTO Driven Generator
Current World Environment Vol. 11(2), 544-553 (2016) An Approach for Power Generation with Reduced Fuel Consumption using PTO Driven Generator MANISH PATEL* and H. RAHEMAN Agricultural and Food Engineering
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION TIMING BELT Removal 1. Disconnect negative battery cable. On Millenia, raise and support vehicle. Remove right front wheel. Remove lower engine covers. 2. On all models, remove accessory
More informationDesign of Road Power Generator (RPG):an Alternate Energy Source for Sustainability
Design of Road Power Generator (RPG):an Alternate Energy Source for Sustainability Ashwin Chandwani 1* Amit N. Patel 1# Abhay Kothari 2 Department of Electrical Engineering Institute of Technology, Nirma
More informationDESIGN AND CONSTRUCTION OF A TIDAL TO ELECTRICAL ENERGY CONVERTER (WITH MATLAB SIMULINK)
DESIGN AND CONSTRUCTION OF A TIDAL TO ELECTRICAL ENERGY CONVERTER (WITH MATLAB SIMULINK) Tamunotonye Charles Mackinson Department of Electronics and Communication Engineering, All Nations University College
More informationCONCEPTUAL DESIGN OF A NEW TYPE OF ENGINE FOR VARIOUS APPLICATIONS WITH EXPECTED 10% HIGHER OVERALL EFFICIENCY
International Journal of Mechanical and Production Engineering Research and Development (IJMPERD ) Vol.1, Issue 2 Dec 2011 58-65 TJPRC Pvt. Ltd., CONCEPTUAL DESIGN OF A NEW TYPE OF ENGINE FOR VARIOUS APPLICATIONS
More informationDesign and Calibration of Epicyclic Gear Transmission Dynamometer for Rural use
Journal of Experimental Research. March 203, Vol No www.er-journal.com E-mail: edi tor-in-chief@er-journal.com Received: Dec. 5, 202 Design and Calibration of Epicyclic Gear Transmission Dynamometer for
More informationOrientalmotor. Development of K II Series Hypoid Geared Motor
Development of K II Series Hypoid Geared Motor The motor industry was looking for a geared motor that would downsize, reduce loss and provide high torque. This led our company to develop the K II series,
More informationGearless Power Transmission-Offset Parallel Shaft Coupling
Gearless Power Transmission-Offset Parallel Shaft Coupling Mahantesh Tanodi 1, S. B. Yapalaparvi 2, Anand. C. Mattikalli 3, D. N. Inamdar 2, G. V. Chiniwalar 2 1 PG Scholar, Department of Mechanical Engineering,
More informationEffortless Water Lifting Bucket Elevator Biswa Bihari Rath 1, Nabnit Panigrahi 2
Effortless Water Lifting Bucket Elevator Biswa Bihari Rath 1, Nabnit Panigrahi 2 1 Assistant Professor, Gandhi Institute For Technology, Bhubaneswar, Odisha India 2 Dean Research, Gandhi Institute For
More informationDesign and Force Analysis of Slider Crank Mechanism for Film Transport Used In VFFS Machine
Design and Force Analysis of Slider Crank Mechanism for Film Transport Used In VFFS Machine KITTUR RAVI ASHOK 1 1M.Tech Student (Design Engineering), KLE Dr. M S Sheshgiri College of Engineering and Technology,
More informationPART V. PADDY SEPARATION
PART V. PADDY SEPARATION In the paddy hullers of a rice mill not all the paddy grains are hulled at once. The huller efficiency, namely the percentage of paddy actually hulled with a minimum of breakage,
More informationPublished by: PIONEER RESEARCH & DEVELOPMENT GROUP ( 1
Advanced Development Of Semi-Automatic Traction Control System Using Differential Unit ABSTRACT S.Jesu Benner 1, M.Mugesh 2, R.Sunil 3 1,2,3 UNIVERSITY COLLEGE OF ENGINEERING ARNI, ARNI, TAMIL NADU, INDIA
More informationGeneration of Electricity from Road Transport Pressure
Generation of Electricity from Road Transport Pressure Dr V V Prathibha Bharathi Professor, Department of Mechanical Engineering, K. Haradeep Student, Department of Mechanical Engineering, K.Pavan Sai
More informationTips & Technology For Bosch business partners
Tips & Technology For Bosch business partners Current topics for successful workshops No. 05 Trucks Starters and starter systems Part 1 Requirements and functions Internal combustion engines must be cranked
More informationStress and Design Analysis of Triple Reduction Gearbox Casing
IJIRST International Journal for Innovative Research in Science & Technology Volume 2 Issue 02 July 2015 ISSN (online): 2349-6010 Stress and Design Analysis of Triple Reduction Gearbox Casing Mitesh Patel
More informationAmerican International Journal of Research in Science, Technology, Engineering & Mathematics INDIA
American International Journal of Research in Science, Technology, Engineering & Mathematics Available online at http://www.iasir.net ISSN (Print): 2328-3491, ISSN (Online): 2328-3580, ISSN (CD-ROM): 2328-3629
More informationFloating Oscillator based Electric Generator using Mechanical Energy Harvesting
Floating Oscillator based Electric Generator using Mechanical Energy Harvesting V Gukan 1, T K Balasekaran 2, E ArunMozhi Devan 3, G Udhaya Kumar 4 1,2,3Student, Dept. of EEE, Valliammai Engineering College,
More informationPerformance Evaluation of 4-WD Tractor at Various Gear rpm Combinations with Three Bottom M. B. Plough
Performance Evaluation of 4-WD Tractor at Various Gear rpm Combinations with Three Bottom M. B. Plough S. B. Patil & A. D. Chendake Assistant Professor, Dept. of FMPE, Assistant Professor, Dept. of RES,
More informationDESIGN OF FRONT END ACCESSORIES FOR A TWO CYLINDER ENGINE
DESIGN OF FRONT END ACCESSORIES FOR A TWO CYLINDER ENGINE Bhushan Bissa¹, Manish Dakhore², Rahul Waghmare 3 Assistant Professor, SRCOEM, Nagpur, India Email: 1 bissa_bhushan@yahoo.co.in, 2 manish.dakhore@gmail.com,
More information11. GEAR TRANSMISSIONS
11. GEAR TRANSMISSIONS 11.1. GENERAL CONSIDERATIONS Gears are one of the most important elements used in machinery. There are few mechanical devices that do not have the need to transmit power and motion
More information1998 Subaru Forester
Inspection 1. Inspect timing belt teeth for breaks, cracks or wear. Inspect belt for signs of oil contamination. When inspecting timing belt, do not bend less than a radius of 2.36" (6.0 mm). Replace belt
More informationReview Paper on Design and Development of Coupling Torque Endurance Test Machine with Variable Torque and Chamber Adjustment
Review Paper on Design and Development of Coupling Torque Endurance Test Machine with Variable Torque and Chamber Adjustment 1. Mr. Borude S.C.(P.G. Student, JSPM s ICOER, Pune), 2.Prof. Biradar N.S.(HOD
More informationAddress for Correspondence
Research Article DESIGN AND STRUCTURAL ANALYSIS OF DIFFERENTIAL GEAR BOX AT DIFFERENT LOADS C.Veeranjaneyulu 1, U. Hari Babu 2 Address for Correspondence 1 PG Student, 2 Professor Department of Mechanical
More informationA New Device to Measure Instantaneous Swept Volume of Reciprocating Machines/Compressors
Purdue University Purdue e-pubs International Compressor Engineering Conference School of Mechanical Engineering 2004 A New Device to Measure Instantaneous Swept Volume of Reciprocating Machines/Compressors
More informationREDUCTION OF IDLE-HUNTING IN DIESEL FUEL INJECTION PUMP
REDUCTION OF IDLE-HUNTING IN DIESEL FUEL INJECTION PUMP Mr. Veeresha G 1,Vijay Kumar S 2, Chandan Kumar S,3,Chetan Kumar Patil 4,Shashank Reddy J 5 1Assistant Professor, Department of Mechanical Engineering
More informationTECHNOLOGY MECHANISMS
TECHNOLOGY MECHANISMS 3º ESO IES CHAN DO MONTE URTAZA 1 WHAT IS A MECHANISM? Mechanism are devices that have been designed to make jobs easier. They all have certain things in common: They involve some
More informationTheory of Machines. CH-1: Fundamentals and type of Mechanisms
CH-1: Fundamentals and type of Mechanisms 1. Define kinematic link and kinematic chain. 2. Enlist the types of constrained motion. Draw a label sketch of any one. 3. Define (1) Mechanism (2) Inversion
More informationMoments. It doesn t fall because of the presence of a counter balance weight on the right-hand side. The boom is therefore balanced.
Moments The crane in the image below looks unstable, as though it should topple over. There appears to be too much of the boom on the left-hand side of the tower. It doesn t fall because of the presence
More informationAssessment of Fatigue and Modal Analysis of Camshaft
ISSN 2395-1621 Assessment of Fatigue and Modal Analysis of Camshaft #1 V. M. Kalshetti, # 2 H.V. Vankudre #1 vmkalshetti13.scoe@gmail.com 1 #12 Department of Mechanical Engineering, Savitribai Phule Pune
More informationELECTROMAGNETIC BRAKING SYSTEM
ELECTROMAGNETIC BRAKING SYSTEM 1 Krunal Prajapati, 2Rahul Vibhandik, 3Devendrasinh Baria, 4Yash Patel Student, Automobile department, Laxmi institute of Technology, Sarigam-Valsad. Gujarat Corresponding
More informationTesting Of Fluid Viscous Damper
Testing Of Fluid Viscous Damper Feng Qian & Sunwei Ding, Jingjing Song Shanghai Research Institute of Materials, China Dr. Chien-Chih Chen US.VF Corp, Omni Device, China SUMMARY: The Fluid Viscous Damper
More information2005 Hyundai Tucson LX. On some models, engine is equipped with a timing belt and timing chain. Inspect timing chain when replacing timing belt.
TIMING BELT NOTE: On some models, engine is equipped with a timing belt and timing chain. Inspect timing chain when replacing timing belt. Removal 1. Remove the engine cover. See Fig. 1. 2. Remove right
More informationENG-05, Camshaft (Timing) Belt and Balance Shaft Belt Removal
ENG-05, Camshaft (Timing) Belt and Balance Shaft Belt Removal Tools Jack stands Floor Jack Metric Socket set Metric Wrench set Porsche Timing Belt Tension tool (P9201) Flywheel Lock (P9206) Balance Shaft
More informationEffect of prime mover speed on power factor of Grid Connected low capacity Induction Generator (GCIG)
Effect of prime mover speed on power factor of Grid Connected low capacity Induction Generator (GCIG) 1 Mali Richa Pravinchandra, 2 Prof. Bijal Mehta, 3 Mihir D. Raval 1 PG student, 2 Assistant Professor,
More informationTiming Belt Replacement
Timing Belt Replacement Tools Required Timing Belt Alignment Kit Crank Hub TORX Socket Removal Procedure 1. Disconnect the negative battery cable. 2. Remove the timing belt front cover. 3. Rotate the crankshaft
More informationME6601 DESIGN OF TRANSMISSION SYSTEMS
SYED AMMAL ENGINEERING COLLEGE (Approved by the AICTE, New Delhi, Govt. of Tamilnadu and Affiliated to Anna University, Chennai) Established in 1998 - An ISO 9001:2008 Certified Institution Dr. E.M.Abdullah
More informationSYSTHESIS OF TROLLEY CUM WHEELCHAIR FOR PATIENT HANDLING
SYSTHESIS OF TROLLEY CUM WHEELCHAIR FOR PATIENT HANDLING Ehsanullah Khan Dr. C.C.Handa Dr. R.D.Askhedkar ABSTRACT Handling of patient from hospital bed to CT-Scan, MR Scan, X-Ray, Sonography centre etc
More informationDesign and Fabrication of Sequencing Circuit with Single Double Acting Cylinder
Design and Fabrication of Sequencing Circuit with Single Double Acting Cylinder V.G.Vijaya Department of Mechatronics Engineering, Bharath University, Chennai 600073, India ABSTRACT: This project deals
More information(POWER TRANSMISSION Methods)
UNIT-5 (POWER TRANSMISSION Methods) It is a method by which you can transfer cyclic motion from one place to another or one pulley to another pulley. The ways by which we can transfer cyclic motion are:-
More informationSemi-Active Suspension for an Automobile
Semi-Active Suspension for an Automobile Pavan Kumar.G 1 Mechanical Engineering PESIT Bangalore, India M. Sambasiva Rao 2 Mechanical Engineering PESIT Bangalore, India Abstract Handling characteristics
More informationPIONEER RESEARCH & DEVELOPMENT GROUP
Design and Stress Analysis of Tow Bar for Medium Sized Portable Compressors Pankaj Khannade 1, Akash Chitnis 2, Gangadhar Jagdale 3 1,2 Mechanical Department, University of Pune/ Smt. Kashibai Navale College
More informatione t Performance of Extended Inlet and Extended Outlet Tube on Single Expansion Chamber for Noise Reduction
e t International Journal on Emerging Technologies 7(1): 37-41(2016) ISSN No. (Print) : 0975-8364 ISSN No. (Online) : 2249-3255 Performance of Extended Inlet and Extended Outlet Tube on Single Expansion
More informationA STUDY ON THE PROPELLER SHAFT OF CAR USING CARBON COMPOSITE FIBER FOR LIGHT WEIGHT
International Journal of Mechanical Engineering and Technology (IJMET) Volume 9, Issue 5, May 2018, pp. 603 611, Article ID: IJMET_09_05_066 Available online at http://www.iaeme.com/ijmet/issues.asp?jtype=ijmet&vtype=9&itype=5
More informationDESIGN AND AUTOMATION OF CYLINDER HEAD VALVE GUIDE GROOVE DETECTION SYSTEM
DESIGN AND AUTOMATION OF CYLINDER HEAD VALVE GUIDE GROOVE DETECTION SYSTEM 1 NIRMAL KANNAN.V, 2 RAMYA.R, 3 KIRUBASHANKAR.T.S 1 Professor, V.S.B.Engineering College/Anna University, Karur, Tamilnadu, India
More informationDesign of Components used in Hoisting Mechanism of an EOT Crane: A Critical Literature Review
Design of Components used in Hoisting Mechanism of an EOT Crane: A Critical Literature Review Mr. Swapnil K. Agrawal Department of Mechanical Engineering Vidarbha Institute of Technology, Nagpur, India
More informationBalancing of Reciprocating Parts
Balancing of Reciprocating Parts We had these forces: Primary and Secondary Unbalanced Forces of Reciprocating Masses m = Mass of the reciprocating parts, l = Length of the connecting rod PC, r = Radius
More informationModule 1: Introduction to Drive Trains
Introduction ÂÂ Basic Components of a Drive Train Operation of a Drive Train Working Applications Types of Drives Types of Gears Formula for Calculating Gear Ratio Determining Gear Rotation Introduction
More informationStructural Analysis of Differential Gearbox
Structural Analysis of Differential Gearbox Daniel Das.A Seenivasan.S Assistant Professor Karthick.S Assistant Professor Abstract- The main aim of this paper is to focus on the mechanical design and analysis
More information