DESIGN AND MANUFACTURING ELECTRICAL CAR JACK D.C. 12 VOLT

Size: px
Start display at page:

Download "DESIGN AND MANUFACTURING ELECTRICAL CAR JACK D.C. 12 VOLT"

Transcription

1 International Journal of Mechanical Engineering and Technology (IJMET) Volume 8, Issue 6, June 207, pp , Article ID: IJMET_08_06_02 Available online at aeme.com/ijmet/issues.asp?jtype=ijmet&vtyp pe=8&itype=6 ISSN Print: and ISSN Online: IAEME Publication Scopus Indexed DESIGN AND MANUFACTURING ELECTRICAL BOTTLE CAR JACK D.C. 2 VOLT Timur Choban Khidir Mechanical Department, Kirkuk University / College of Engineering, Iraq ABSTRACT The tire puncture problem of the cars on the roads, especially on the highway roads generally needs manual human force to solve the problem by using a mechanical scissor car jack. Our work focused on a bottle carjack and adapting D.C. motor (2 volts) with chain-sprocket set to design a suitable machine. Lifting the car to solve the puncture problem with this new machine is easier, safer, abbreviate the time and more reliable for persons who suffer from their health s. We used drilling, grinding, milling, and welding machines to make up this work. The designed jack had been tested on a passenger car and passed successfully. We used Solidworks software program to achieve the goal. Key words: Puncture, SOILDWORKS, D.C. motor, bottle carjack, chain-sproket. Cite this Article: Timur Choban Khidir. Design and Manufacturing Electrical Bottle Car Jack D.C. 2 Volt. International Journal of Mechanical Engineering and Technology, 8(6), 207, pp MET/issues.asp?JType=IJMET&VType=8&ITy ype=6. INTRODUCTION During side road emergency i.e. tire puncture the jack is used to raise the car. A mechanical scissor car jack is a device used to facilitate vehicle maintenances by lifting all or parts of a vehicle into the air []. Nowadays, different types of car jacks have been remodeled for raising vehicles from the land surface. Generally, the available carjacks manually operated by turning a lead screw which is needed to human effort to do requested job. So, the operator may hurt his back and beside that he spends more time to replace the punctured tire with the spare tire that exists in the car [2]. Hence, to save from the effort and the time it's needed to electrical portable jack which is necessary to repair the car on the side way [3]. Which is performed with electric D.C. motor (2 volts) with bottle carjack and this motor must hold the load more than 000 kg. This type of bottle carjack consistss of a power screw that converts the rotary motion to a linear motion. These jacks are compact in size, but are designed and built for performance to lift vehicles. The aim of this study is to remodel a car jack which is safe, able to lift and lowering the car without spending much human effort and easy to be operated. The design and analysis of modified carjack are discussed in this study editor@iaeme.com

2 Design and Manufacturing Electrical Bottle Car Jack D.C. 2 Volt 2. WORKING OF ELECTRICALLY OPERATED JACK When running the motor, transmission of movement of the motor to shaft caller with first sprocket and by chain starts picked up movement to the second sprocket, and thus the movement transition to jack and thus jack begins to lift a car. D.C. motor 2V receives electricity from the battery through the car. The bottle carjack also contains the gearbox and it helps the device to increase torque. 3. DESIGN AND DEVELOPMENT OF JACK Figure shows remodeled bottle jack. The main components required for the development of this jack are: Original bottle jack. Shaft arm for jack. Chain and Sprocket Set. D.C. Motor for windshield wiper motor (Window Motors) for bus. Base for jack and Sprocket Set. Table includes details of all components required for manufacturing the actual model or prototype of electrically operated bottle jack. Table List of components. Component No. Description Bearing 2 Base 3 Chain and Sprocket Set 4 D.C. Motor 5 Shaft arm 6 Bolt 7 Nut The isometric view of the bottle carjack is shown below: Qty Figure Isometric view of CAD model for Modified bottle jack 20 editor@iaeme.com

3 Timur Choban Khidir Figure 2 shows the actual model of electrically operated carjack. The prototype is manufactured by using the jack and bus windshield wiper motor. (a) (b) 4. SPECIFICATIONS Specifications of Sprocket and Chain Figure 2 Model factory of modified bottle jack Bottom Diameter of larger sprocket = 45 mm and Outside Diameter = 50 mm. Bottom Diameter of smaller sprocket = 30 mm and Outside Diameter = 35 mm. Center distances = 46 mm. No. of teeth of the largest sprocket = 24 No. of teeth of the smallest sprocket = 6 No. of chain link = 32 Material : Stainless Steel Specifications of Bottle Jack Overall height of Jack = 390 mm, Out diameter = 40 mm, in diameter = 38 mm, Material : cast carbon steel Specifications of D.C. Motor Power = 30 W, Torque = 6 N.m, Speed = 75 r.p.m. Voltage = 2 V editor@iaeme.com

4 Design and Manufacturing Electrical Bottle Car Jack D.C. 2 Volt Figure 3 D.C. motor 5. ANALYSIS This section shows the details of FEA of this remodeled prototype. The FEA Method is the easiest technique to the theoretical method to determine the stress remodeled in various components of bottle jack. In this study FEA is carried out in SOILDWORKS to calculate the max. (stress, deformation and strain) in the main parts of the system when applied with boundary conditions. Steps in the Analysis Step : Analysis jack for 000 kg (Stress, deformation, Strain) Figure 4 Stress Analysis Figure 5 Deformation Analysis Figure 6 Strain Analysis editor@iaeme.com

5 Timur Choban Khidir Step 2: Analysis jack for 2000 kg (Stress, deformation, Strain) Figure 7 Stress Analysis Figure 8 Deformation Analysis Figure 9 Strain Analysis Step 3: Analysis of torque for arm shaft jack: 6 N.m Figure 0 Stress Analysis Figure Strain Analysis editor@iaeme.com

6 Design and Manufacturing Electrical Bottle Car Jack D.C. 2 Volt Step 4: Analysis torque of smaller sprocket for Outside Diameter 35 mm: 6 N.m Figure 2 Stress Analysis Figure 3 Deformation Analysis Figure 4 Strain Analysis Step 5: Chain link analysis: 6 N.m, F = N, smaller sprocket = 35 mm Figure 5 Stress Analysis Figure 6 Deformation Analysis Figure 7 Strain Analysis editor@iaeme.com

7 Timur Choban Khidir 6. CONCLUSIONS The main physical parameters of the design with reasonable assumptions have been determined through practical considerations. Cast alloy is used as the materials for both chains due to its high strength, toughness, and its economical effects and cast carbon steel used in Jack. Depending on the analysis of FEA, it shows that the max. nodal displacement value of the system of carjack is about.048e-00 mm as shown in Figure 8 and max. Von Mises 3.625e+008 shows in Figure 7, when max. load (9620 N) applied Furthermore, it seen that max. Von Mises stress, max. safe point. And we tried this carjack on the vehicle (Kia Rio model 2005 its curb weight is 090 kg) practically to see wether it rasie the vehicle or not, we saw it is succeeded as seen in the figure 2-b. 7. RECOMMENDATIONS In this model we currently used chain and sprocket set for transmission. In the future, maybe use the gears or special kind of hydraulic motor and work comparison between each type and choose the best type that transmits power and motion. REFERENCES [] Budyanas, G.R. and Nisbett, K.J., (2008), Shigley s Mechanical Engineering Design, McGraw-Hill Companies 8th Edition, pp 67 40, ISBN: [2] Khurmi, R.S. and Gupta, J.K. (2005), A Teaxt book of Machine Design, Eurasia Publication House (P.V.T) Ltd. 4th Edition, 230 pp. ISBN: [3] Lonon, E.M., East Orange, N.J Motorized Jack, US Patent No Date of patent. Feb 4, 992. AUTHOR DETAILS TIMUR CHOBAN KHIDIR B.Sc. University of Technology Baghdad / Mech. Eng MsD. Gazi University (Ankara) / Turkey 200 Specialist: Applied Mechanic Lecturer in College of Engineering / Kirkuk University editor@iaeme.com

Design, Construction and Testing of an Electric Powered Toggle Jack Mechanism

Design, Construction and Testing of an Electric Powered Toggle Jack Mechanism Design, Construction and Testing of an Electric Powered Toggle Jack Mechanism Ipilakyaa T.D. 1, Achirgbenda V.T. 2, Gbashi S. 3 1Department of Mechanical Engineering, University of Agriculture Makurdi,

More information

DESIGNING AND ANALYSING STAIR CASE LIFT SYSTEM

DESIGNING AND ANALYSING STAIR CASE LIFT SYSTEM DESIGNING AND ANALYSING STAIR CASE LIFT SYSTEM Timur Choban Khidir 1, Abbas Mohammed Ismael 2 & Ayaz Aydin Abduljabbar 3 1, 2, 3 Kirkuk University / College of Engineering - Mechanical Department, IRAQ

More information

MANUFACTURING OF STEERING COMPONENTS FOR A RACE CAR

MANUFACTURING OF STEERING COMPONENTS FOR A RACE CAR International Journal of Mechanical Engineering and Technology (IJMET) Volume 8, Issue 6, June 2017, pp. 207 211, Article ID: IJMET_08_06_022 Available online at http://www.ia aeme.com/ijmet/issues.asp?jtype=ijmet&vtyp

More information

M.E. Scholar (Design and Thermal), I.E.T-DAVV, Indore, M.P., India. 2

M.E. Scholar (Design and Thermal), I.E.T-DAVV, Indore, M.P., India. 2 IJESRT INTERNATIONAL JOURNAL OF ENGINEERING SCIENCES & RESEARCH TECHNOLOGY PARAMETRIC ANALYSIS OF SPUR GEAR TO DETERMINE THE EFFECT OF VARIATION OF R.P.M. AND PRESSURE ANGLE ON STRESS PRODUCED Yogendra

More information

STRESS AND THERMAL ANALYSIS OF CLUTCH PLATE

STRESS AND THERMAL ANALYSIS OF CLUTCH PLATE International Journal of Mechanical Engineering and Technology (IJMET) Volume 9, Issue 3, March 2018, pp. 611 618, Article ID: IJMET_09_03_063 Available online at http://www.iaeme.com/ijmet/issues.asp?jtype=ijmet&vtype=9&itype=3

More information

MODELLING AND STRUCTURAL ANALYSIS OF A GO-KART VEHICLE CHASSIS FRAME

MODELLING AND STRUCTURAL ANALYSIS OF A GO-KART VEHICLE CHASSIS FRAME International Journal of Mechanical Engineering and Technology (IJMET) Volume 8, Issue 6, June 2017, pp. 305 311, Article ID: IJMET_08_06_031 Available online at http://www.ia aeme.com/ijmet/issues.asp?jtype=ijmet&vtyp

More information

GEARBOX DESIGN FOR CNC LATHE

GEARBOX DESIGN FOR CNC LATHE GEARBOX DESIGN FOR CNC LATHE Prof. Reji Mathew 1, Linto P Anto 2, Adith Shajan 3, Basil P Thomas 4, Elisa Manoj 5, Kuriakose M Renji 6 1Professor, Department of Mechanical Engineering, Mar Athanasius College

More information

Modification of an Existing Small Hydraulic Jack for Lifting Light Duty Vehicle

Modification of an Existing Small Hydraulic Jack for Lifting Light Duty Vehicle International Journal of Science and Technology Volume 5 No. 11, November, 2016 Modification of an Existing Small Hydraulic Jack for Lifting Light Duty Vehicle S.K. Amedorme 1, Y.A.K. Fiagbe 2 1 School

More information

Design and Analysis of Pressure Die Casting Die for Side Differential Cover of Mini truck

Design and Analysis of Pressure Die Casting Die for Side Differential Cover of Mini truck Design and Analysis of Pressure Die Casting Die for Side Differential Cover of Mini truck 1 A Chakravarthi P.G student, Department of Mechanical Engineering,KSRM CE, kadapa-516003 2. R Rama Krishna Reddy,

More information

Design and Analysis of Clutch Plate for Automatic Single Plate Clutch

Design and Analysis of Clutch Plate for Automatic Single Plate Clutch ISSN 2395-1621 Design and Analysis of Clutch Plate for Automatic Single Plate Clutch #1 Ravikiran M. Tate, #2 S. H. Sarje 1 rtate26@gmail.com 2 suhas_sarje7@rediffmail.com #12 Mechanical Department, JSPM

More information

Design and Analysis of Mini Dumper

Design and Analysis of Mini Dumper Design and Analysis of Mini Dumper Ajay P V 1 Vishnu K M 4 Sreeraj J Menon 7 Daise T Mechery 2 Afsal Fajarudheen 5 Akhil Viswanath K C 8 Assistant Professor Gokul Krishnan T N 3 Delvin T D 6 Abstract A

More information

Design, Development and analysis of electrically operated toggle jack using power of car battery

Design, Development and analysis of electrically operated toggle jack using power of car battery ISSN (e): 2250 3005 Vol, 04 Issue, 7 July 2014 International Journal of Computational Engineering Research (IJCER) Design, Development and analysis of electrically operated toggle jack using power of car

More information

STUDY AND ANALYSIS OF TIRE CHANGING MACHINE COMPONENTS

STUDY AND ANALYSIS OF TIRE CHANGING MACHINE COMPONENTS STUDY AND ANALYSIS OF TIRE CHANGING MACHINE COMPONENTS Mr. Sutar Gururaj 1,Mr. Suryawanshi Bhairavnath 2, Mr. Tengle Kiran 3 Mr. Thaware Madan 4 1,2,3,4UG, Mechanical Engineering, UCOER, Pune, Maharashtra,

More information

MULTI-USE FLOOR CLEANING MACHINE

MULTI-USE FLOOR CLEANING MACHINE International Journal of Mechanical Engineering and Technology (IJMET) Volume 8, Issue 5, May 2017, pp. 656 664, Article ID: IJMET_08_05_072 Available online at http://www.iaeme.com/ijmet/issues.asp?jtype=ijmet&vtype=8&itype=5

More information

DESIGN AND ANALYSIS OF HARMONIC ANALYSIS OF THREE WHEELER AUTO CHASSIS USING ANSYS

DESIGN AND ANALYSIS OF HARMONIC ANALYSIS OF THREE WHEELER AUTO CHASSIS USING ANSYS International Journal of Mechanical Engineering and Technology (IJMET) Volume 9, Issue 12, December 218, pp. 195 111, Article ID: IJMET_9_12_11 Available online at http://www.iaeme.com/ijmet/issues.asp?jtype=ijmet&vtype=9&itype=12

More information

STRUCTURAL ANALYSIS OF SPUR GEAR USING FEM

STRUCTURAL ANALYSIS OF SPUR GEAR USING FEM International Journal of Mechanical Engineering and Technology (IJMET) Volume 7, Issue 6, November December 2016, pp.01 08, Article ID: IJMET_07_06_001 Available online at http://www.iaeme.com/ijmet/issues.asp?jtype=ijmet&vtype=7&itype=6

More information

COMPARISON OF ANALYTICAL & FEA OF CONTACT ANALYSIS OF SPUR GEAR DRIVE

COMPARISON OF ANALYTICAL & FEA OF CONTACT ANALYSIS OF SPUR GEAR DRIVE COMPARISON OF ANALYTICAL & FEA OF CONTACT ANALYSIS OF SPUR GEAR DRIVE Sachin Almelkar 1, Prof I.G.Bhavi 2 1M.Tech (Machine Design). B L D E A s Dr.P.G. Halakatti College Of Engineering and Technology,Vijayapur,

More information

Design and Analysis of 2 - Speed gearbox for Bicycles

Design and Analysis of 2 - Speed gearbox for Bicycles Design and Analysis of 2 - Speed gearbox for Bicycles Venu Akhil Kumar Parakala, Lucky Purushwani SMBS, VIT University, Chennai Campus, Vandalur-kelambakam road, Chennai-600127 ABSTRACT This paper sees

More information

Design and Investigation of Safety Cross Stand For Scrambler

Design and Investigation of Safety Cross Stand For Scrambler Design and Investigation of Safety Cross Stand For Scrambler L.Natrayan 1, M.S.Santhosh 2, S.Yogeshwaran 3 1 PG Scholar, Department of Mechanical Engineering, Selvam College of technology-namakkal 2 Assistant

More information

A STUDY ON THE PROPELLER SHAFT OF CAR USING CARBON COMPOSITE FIBER FOR LIGHT WEIGHT

A STUDY ON THE PROPELLER SHAFT OF CAR USING CARBON COMPOSITE FIBER FOR LIGHT WEIGHT International Journal of Mechanical Engineering and Technology (IJMET) Volume 9, Issue 5, May 2018, pp. 603 611, Article ID: IJMET_09_05_066 Available online at http://www.iaeme.com/ijmet/issues.asp?jtype=ijmet&vtype=9&itype=5

More information

DESIGN AND DEVELOPMENT OF IC ENGINE GO-KART

DESIGN AND DEVELOPMENT OF IC ENGINE GO-KART DESIGN AND DEVELOPMENT OF IC ENGINE GO-KART AkshayB. Khot 1, KunalJ. Mahekar 2, VaibhavJ. Mahekar 3, GurunathS. Patil 4, MohanishM. Patil 5, Prof. S. P. Jarag 6 BE Student, Department of Mechanical Engineering,

More information

Development of Motorized Car Jack

Development of Motorized Car Jack Development of Motorized Car Jack Ravi Kumar D Assistant Professor Mechanical Engineering SRM University Shubham Choudhary U.G. Student Mechanical Engineering SRM University Devanshu Pasbola U.G. Student

More information

Static Stress Analysis of Piston

Static Stress Analysis of Piston Static Stress Analysis of Piston Kevin Agrawal B. E. Student, Mechanical Engineering, BITS Pilani K. K. Birla Goa Campus. AH7-352, BITS Pilani, K. K. Birla Goa Campus, NH 17B, Zuarinagar 403726. Parva

More information

Load Analysis and Multi Body Dynamics Analysis of Connecting Rod in Single Cylinder 4 Stroke Engine

Load Analysis and Multi Body Dynamics Analysis of Connecting Rod in Single Cylinder 4 Stroke Engine IJSRD - International Journal for Scientific Research & Development Vol. 3, Issue 08, 2015 ISSN (online): 2321-0613 Load Analysis and Multi Body Dynamics Analysis of Connecting Rod in Single Cylinder 4

More information

Increase Factor of Safety of Go-Kart Chassis during Front Impact Analysis

Increase Factor of Safety of Go-Kart Chassis during Front Impact Analysis IJIRST International Journal for Innovative Research in Science & Technology Volume 3 Issue 04 September 2016 ISSN (online): 2349-6010 Increase Factor of Safety of Go-Kart Chassis during Front Impact Analysis

More information

DESIGN AND ANALYSIS OF DIFFERENTIAL GEAR BOX IN AUTOMOBILES

DESIGN AND ANALYSIS OF DIFFERENTIAL GEAR BOX IN AUTOMOBILES International Journal of Mechanical Engineering and Technology (IJMET) Volume 8, Issue 5, May 2017, pp. 175 185 Article ID: IJMET_08_05_019 Available online at http:// http://www.iaeme.com/ijmet/issues.asp?jtype=ijmet&vtype=8&itype=5

More information

DESIGN METHODOLOGY FOR STEERING SYSTEM OF AN ATV

DESIGN METHODOLOGY FOR STEERING SYSTEM OF AN ATV International Journal of Mechanical Engineering and Technology (IJMET) Volume 7, Issue 5, September October 2016, pp.272 277, Article ID: IJMET_07_05_027 Available online at http://www.iaeme.com/ijmet/issues.asp?jtype=ijmet&vtype=7&itype=5

More information

Address for Correspondence

Address for Correspondence Research Article DESIGN AND STRUCTURAL ANALYSIS OF DIFFERENTIAL GEAR BOX AT DIFFERENT LOADS C.Veeranjaneyulu 1, U. Hari Babu 2 Address for Correspondence 1 PG Student, 2 Professor Department of Mechanical

More information

Keywords: Von Mises, Piston, Thermal Analysis, Pressure, CATIAV5R20, ANSYS14 I. INTRODUCTION

Keywords: Von Mises, Piston, Thermal Analysis, Pressure, CATIAV5R20, ANSYS14 I. INTRODUCTION Finite Element Analysis of IC Engine Piston Using Thermo Mechanical Approach 1 S.Sathishkumar, Dr.M.Kannan and 3 V.Raguraman, 1 PG Scholar, Professor, 3 Assistant professor, 1,,3 Department of Mechanical

More information

Design and Vibrational Analysis of Flexible Coupling (Pin-type)

Design and Vibrational Analysis of Flexible Coupling (Pin-type) Design and Vibrational Analysis of Flexible Coupling (Pin-type) 1 S.BASKARAN, ARUN.S 1 Assistant professor Department of Mechanical Engineering, KSR Institute for Engineering and Technology, Tiruchengode,

More information

DESIGN AND ANALYSIS OF COMPOSITE LEAF SPRING

DESIGN AND ANALYSIS OF COMPOSITE LEAF SPRING International Journal of Mechanical Engineering and Technology (IJMET) Volume 7, Issue 5, September October 2016, pp.177 183, Article ID: IJMET_07_05_019 Available online at http://www.iaeme.com/ijmet/issues.asp?jtype=ijmet&vtype=7&itype=5

More information

A STUDY ON DIESEL ENGINE PERFORMANCE DEPENDS ON BP AND BSFC BY APPLYING DIFFERENT INJECTION PRESSURE

A STUDY ON DIESEL ENGINE PERFORMANCE DEPENDS ON BP AND BSFC BY APPLYING DIFFERENT INJECTION PRESSURE International Journal of Mechanical Engineering and Technology (IJMET) Volume 9, Issue 11, November 2018, pp. 599 603, Article ID: IJMET_09_11_059 Available online at http://www.iaeme.com/ijmet/issues.asp?jtype=ijmet&vtype=9&itype=11

More information

DEVELOPMENT OF A FOOT OPERATED HYDRAULIC LIFTER FOR AUTOMOBILE WORKSHOPS

DEVELOPMENT OF A FOOT OPERATED HYDRAULIC LIFTER FOR AUTOMOBILE WORKSHOPS DEVELOPMENT OF A FOOT OPERATED HYDRAULIC LIFTER FOR AUTOMOBILE WORKSHOPS Ikechukwu Celestine Ugwuoke, Olawale James Okegbile and Ibukun Blessing Ikechukwu Department of Mechanical Engineering, Federal

More information

DESIGN AND ANALYSIS OF STEERING COMPONENTS FOR A RACE CAR

DESIGN AND ANALYSIS OF STEERING COMPONENTS FOR A RACE CAR International Journal of Mechanical Engineering and Technology (IJMET) Volume 8, Issue 6, June 2017, pp. 125 129, Article ID: IJMET_08_06_013 Available online at http://www.ia aeme.com/ijmet/issues.asp?jtype=ijmet&vtyp

More information

DOUBLE WISHBONE SUSPENSION SYSTEM

DOUBLE WISHBONE SUSPENSION SYSTEM International Journal of Mechanical Engineering and Technology (IJMET) Volume 8, Issue 5, May 2017, pp. 249 264 Article ID: IJMET_08_05_027 Available online at http:// http://www.iaeme.com/ijmet/issues.asp?jtype=ijmet&vtype=8&itype=5

More information

Stress and Design Analysis of Triple Reduction Gearbox Casing

Stress and Design Analysis of Triple Reduction Gearbox Casing IJIRST International Journal for Innovative Research in Science & Technology Volume 2 Issue 02 July 2015 ISSN (online): 2349-6010 Stress and Design Analysis of Triple Reduction Gearbox Casing Mitesh Patel

More information

WITH BIO LUBRICANTS JATROPHA OIL, CASTOR OIL, NEEM OIL AND MINERAL OIL (SAE 20W50)

WITH BIO LUBRICANTS JATROPHA OIL, CASTOR OIL, NEEM OIL AND MINERAL OIL (SAE 20W50) and COMPARATIVE Mineral Oil (SAE 20W50), Anand STUDY Kalani OF and Rita FULL Jani, Journal JOURNAL Impact Factor BEARING (2015): 8.8293 WITH BIO LUBRICANTS JATROPHA OIL, CASTOR OIL, NEEM OIL AND MINERAL

More information

MULTI-BODY DYNAMIC ANALYSIS OF AN IC ENGINE PISTON FOR SHAPE OPTIMIZATION

MULTI-BODY DYNAMIC ANALYSIS OF AN IC ENGINE PISTON FOR SHAPE OPTIMIZATION Int. J. Mech. Eng. & Rob. Res. 2014 Shivayogi S Hiremath and I G Bhavi, 2014 Research Paper ISSN 2278 0149 www.ijmerr.com Vol. 3, No. 4, October 2014 2014 IJMERR. All Rights Reserved MULTI-BODY DYNAMIC

More information

MULTISTAGE EPICYCLIC LUG WRENCH

MULTISTAGE EPICYCLIC LUG WRENCH MULTISTAGE EPICYCLIC LUG WRENCH 1 Shinu Baby, 2 Nevin G Ninan, 3 Nithin George, 4 Salu Zachariah, 5 Aju Zachariah Mani 1,2,3,4 Scholar, 5 Assistant Professor, Department of Mechanical Engineering, Saintgits

More information

Chapter 7: Thermal Study of Transmission Gearbox

Chapter 7: Thermal Study of Transmission Gearbox Chapter 7: Thermal Study of Transmission Gearbox 7.1 Introduction The main objective of this chapter is to investigate the performance of automobile transmission gearbox under the influence of load, rotational

More information

Design & Performance Testing of Torque Limiter Timer Belt Spindle Drive for Overload Protection

Design & Performance Testing of Torque Limiter Timer Belt Spindle Drive for Overload Protection Design & Performance Testing of Torque Limiter Timer Belt Spindle Drive for Overload Protection Prof. RAUT L.B. SVERI S, College of Engineering Pandharpur, Solapur University, Solapur, MAHARASTRA KARE

More information

Finite Element Analysis of Clutch Piston Seal

Finite Element Analysis of Clutch Piston Seal Finite Element Analysis of Clutch Piston Seal T. OYA * F. KASAHARA * *Research & Development Center Tribology Research Department Three-dimensional finite element analysis was used to simulate deformation

More information

SPEED DEPENDENT DUAL CALIPER ACTION IN DISC BRAKE

SPEED DEPENDENT DUAL CALIPER ACTION IN DISC BRAKE INTERNATIONAL JOURNAL OF MECHANICAL ENGINEERING AND TECHNOLOGY (IJMET) International Journal of Mechanical Engineering and Technology (IJMET), ISSN 0976 6340(Print), ISSN 0976 6340 (Print) ISSN 0976 6359

More information

Design and Manufacturing of Self Inflating Tire System

Design and Manufacturing of Self Inflating Tire System Design and Manufacturing of Self Inflating Tire System Mahendra Kagane 1, Prathamesh Halande 2, Mayur Chaure 3, Rakshit Tambe 4,Abhijit Bugade 5 1 Student, Mechanical Dept., Smt. Kashibai Navale College

More information

Design, Analysis & Balancing of 5 Cylinder Engine Crankshaft

Design, Analysis & Balancing of 5 Cylinder Engine Crankshaft International OPEN ACCESS Journal Of Modern Engineering Research (IJMER) Design, Analysis & Balancing of 5 Cylinder Engine Crankshaft Yogesh S. Khaladkar 1, Lalit H. Dorik 2, Gaurav M. Mahajan 3, Anil

More information

ANALYSIS OF STRESSES AND DEFLECTIONS IN SPUR GEAR

ANALYSIS OF STRESSES AND DEFLECTIONS IN SPUR GEAR International Journal of Mechanical Engineering and Technology (IJMET) Volume 8, Issue 4, April 2017, pp. 461 473 Article ID: IJMET_08_04_050 Available online at http://www.iaeme.com/ijmet/issues.asp?jtype=ijmet&vtype=8&itype=4

More information

ANALYSIS OF EXISTING TROLLEY AXLE USING ANSYS

ANALYSIS OF EXISTING TROLLEY AXLE USING ANSYS International Journal of Science, Environment and Technology, Vol. 4, No 2, 2015, 293 299 ISSN 2278-3687 (O) 2277-663X (P) ANALYSIS OF EXISTING TROLLEY AXLE USING ANSYS 1 Mr. Harish V. Katore, 2 Mr. Ashitosh

More information

A GEAR COUPLING WITH TAPERED EXCESS LOAD ABSORPTION

A GEAR COUPLING WITH TAPERED EXCESS LOAD ABSORPTION International Journal of Mechanical Engineering and Technology (IJMET) Volume 9, Issue 12, December 2018, pp. 928 942, Article ID: IJMET_09_12_093 Available online at http://www.ia aeme.com/ijmet/issues.asp?jtype=ijmet&vtype=

More information

Finite Element Modeling and Analysis of Vehicle Space Frame with Experimental Validation

Finite Element Modeling and Analysis of Vehicle Space Frame with Experimental Validation Finite Element Modeling and Analysis of Vehicle Space Frame with Experimental Validation Assoc. Prof Dr. Mohammed A.Elhaddad Mechanical Engineering Department Higher Technological Institute, Town of 6

More information

INCREASE IN FATIGUE LIFE OF SPUR GEAR BY INTRODUCING CIRCULAR STRESS RELIEVING FEATURE

INCREASE IN FATIGUE LIFE OF SPUR GEAR BY INTRODUCING CIRCULAR STRESS RELIEVING FEATURE INTERNATIONAL JOURNAL OF MECHANICAL ENGINEERING AND International Journal of Mechanical Engineering and Technology (IJMET), ISSN 0976 6340(Print), ISSN 0976 6359(Online), Volume TECHNOLOGY 6, Issue 5,

More information

Analysis of Turn Table Assembly of Semi- Automatic High Pressure Molding Machine

Analysis of Turn Table Assembly of Semi- Automatic High Pressure Molding Machine Kalpa Publications in Engineering Volume 1, 2017, Pages 259 264 ICRISET2017. International Conference on Research and Innovations in Science, Engineering &Technology. Selected Papers in Engineering Analysis

More information

INTERNATIONAL JOURNAL OF PURE AND APPLIED RESEARCH IN ENGINEERING AND TECHNOLOGY

INTERNATIONAL JOURNAL OF PURE AND APPLIED RESEARCH IN ENGINEERING AND TECHNOLOGY INTERNATIONAL JOURNAL OF PURE AND APPLIED RESEARCH IN ENGINEERING AND TECHNOLOGY A PATH FOR HORIZING YOUR INNOVATIVE WORK DESIGN, ANALYSIS AND OPTIMIZATION OF PISTON OF 180CC ENGINE USING CAE TOOLS NIKHIL

More information

HARMONIC RESPONSE ANALYSIS OF GEARBOX

HARMONIC RESPONSE ANALYSIS OF GEARBOX HARMONIC RESPONSE ANALYSIS OF GEARBOX Rishav Ranjan, Sindhu Srinath and Shanmukha Nagaraj Departmental of Mechanical Engineering, RVCE, Bangalore, India E-Mail: rishav.singh94@gmail.com ABSTRACT Gearbox

More information

New Frontier in Energy, Engineering, Environment & Science (NFEEES-2018 ) Feb

New Frontier in Energy, Engineering, Environment & Science (NFEEES-2018 ) Feb RESEARCH ARTICLE OPEN ACCESS DESIGN AND IMPACT ANALYSIS OF A ROLLCAGE FOR FORMULA HYBRID VEHICLE Aayush Bohra 1, Ajay Sharma 2 1(Mechanical department, Arya College of Engineering & I.T.,kukas, Jaipur)

More information

STRESS AND VIBRATION ANALYSIS ON TWO- STAGE REDUCTION GEARBOX USING FINITE ELEMENTS METHOD

STRESS AND VIBRATION ANALYSIS ON TWO- STAGE REDUCTION GEARBOX USING FINITE ELEMENTS METHOD International Journal of Mechanical Engineering and Technology (IJMET) Volume 9, Issue 8, August 2018, pp. 1111 1125, Article ID: IJMET_09_08_120 Available online at http://www.iaeme.com/ijmet/issues.asp?jtype=ijmet&vtype=9&itype=8

More information

IJESRT. Scientific Journal Impact Factor: (ISRA), Impact Factor: 1.852

IJESRT. Scientific Journal Impact Factor: (ISRA), Impact Factor: 1.852 IJESRT INTERNATIONAL JOURNAL OF ENGINEERING SCIENCES & RESEARCH TECHNOLOGY Design Analysis and Optimization of Piston and Determination of its Thermal Stresses Using CAE Tools Deovrat Vibhandik *1, Ameya

More information

STRESS ANALYSIS OF PISTON USING PRESSURE LOAD AND THERMAL LOAD

STRESS ANALYSIS OF PISTON USING PRESSURE LOAD AND THERMAL LOAD STRESS ANALYSIS OF PISTON USING PRESSURE LOAD AND THERMAL LOAD Vaishali R. Nimbarte 1, Prof. S.D. Khamankar 2 1 Student of M.Tech (CAD/CAM), Rajiv Gandhi College Of Engineering, Research and Technology,

More information

Analysis Of Vehicle Air Compressor Mounting Bracket

Analysis Of Vehicle Air Compressor Mounting Bracket Analysis Of Vehicle Air Compressor Mounting Bracket Murtaza Goawala 1,Rahul Giri 2,Niket Phalke 3,Krishna Singh 4,Prof. Nitin Sall 5 1,2,3,4,5 Automobile Engineering Dept., Theem College Of Engineering,

More information

STRUCTURAL ANALYSIS OF STEERING YOKE OF AN AUTOMOBILE FOR WITHSTANDING TORSION/ SHEAR LOADS

STRUCTURAL ANALYSIS OF STEERING YOKE OF AN AUTOMOBILE FOR WITHSTANDING TORSION/ SHEAR LOADS STRUCTURAL ANALYSIS OF STEERING YOKE OF AN AUTOMOBILE FOR WITHSTANDING TORSION/ SHEAR LOADS S.K.Chandole 1, M.D.Shende 2, M.K.Bhavsar 3 1 PG Student, Mechanical Engineering, S.N.D. COE & RC, Yeola, Nasik,

More information

Analysis Of Gearbox Casing Using FEA

Analysis Of Gearbox Casing Using FEA Analysis Of Gearbox Casing Using FEA Neeta T. Chavan, Student, M.E. Design, Mechanical Department, Pillai Hoc, Maharashtra, India Assistant Prof. Gunchita Kaur-Wadhwa, Mechanical Department Pillai Hoc,

More information

DESIGN AND ANALYSIS OF TELESCOPIC JACK

DESIGN AND ANALYSIS OF TELESCOPIC JACK DESIGN AND ANALYSIS OF TELESCOPIC JACK Ashish Patil 1, Sachin Wangikar 2, Sangam Patil 3, Rajashekhar M S 4 1 Assistant Professor, Mechanical Department, Shaikh College of Engineering and Technology, karnataka,

More information

DESIGN AND ANALYSIS OF LEAF SPRING FOR SOLAR VEHICLE

DESIGN AND ANALYSIS OF LEAF SPRING FOR SOLAR VEHICLE DESIGN AND ANALYSIS OF LEAF SPRING FOR SOLAR VEHICLE MAY MYA DARLI CHO, HTAY HTAY WIN, 3 AUNG KO LATT,,3 Department of Mechanical Engineering, Mandalay Technological University, Mandalay, Myanmar E-mail:

More information

Thermal Analysis of Helical and Spiral Gear Train

Thermal Analysis of Helical and Spiral Gear Train International Journal for Ignited Minds (IJIMIINDS) Thermal Analysis of Helical and Spiral Gear Train Dr. D V Ghewade a, S S Nagarale b & A N Pandav c a Principal, Department of Mechanical, GENESIS, Top-Kolhapur,

More information

Design and Analysis of Go-kart Chassis

Design and Analysis of Go-kart Chassis Design and Analysis of Go-kart Chassis Sannake Aniket S. 1, Shaikh Sameer R. 2, Khandare Shubham A. 3 Prof. S.A.Nehatrao 4 1,2,3 BE Student, mechanical Department, N.B.Navale Sinhagad College Of Engineering,

More information

Comparative study between double wish-bone and macpherson suspension system

Comparative study between double wish-bone and macpherson suspension system IOP Conference Series: Materials Science and Engineering PAPER OPEN ACCESS Comparative study between double wish-bone and macpherson suspension system To cite this article: Shoaib Khan et al 2017 IOP Conf.

More information

STUDY AND ANALYSIS OF CONNECTING ROD PARAMETERS USING ANSYS

STUDY AND ANALYSIS OF CONNECTING ROD PARAMETERS USING ANSYS International Journal of Mechanical Engineering and Technology (IJMET) Volume 7, Issue 4, July Aug 2016, pp.212 220, Article ID: IJMET_07_04_022 Available online at http://www.iaeme.com/ijmet/issues.asp?jtype=ijmet&vtype=7&itype=4

More information

Design and Analysis of Front Lower Control Arm by Using Topology Optimization

Design and Analysis of Front Lower Control Arm by Using Topology Optimization Design and Analysis of Front Lower Control Arm by Using Topology Optimization Prashant Gunjan 1, Amit Sarda 2 12 Department of Mechanical Engineering, Christian College of Engineering and Technology, Bhilai

More information

Analysis of Spur Gear Box Using Software tool Ansys

Analysis of Spur Gear Box Using Software tool Ansys Analysis of Spur Gear Box Using Software tool Ansys K.G.Patel D.N.Patel College of Engineering, Shahada (Maharashtra) S.U.Patil D.N.Patel College of Engineering, Shahada (Maharashtra) H.G.Patil D.N.Patel

More information

Design and Analysis of a steering Rack of an ATV for different materials under static loading conditions

Design and Analysis of a steering Rack of an ATV for different materials under static loading conditions Design and Analysis of a steering Rack of an ATV for different materials under static loading conditions 1 Niraj Kulkarni, 2 Pritam Wani 1 BE Mechanical JNEC Aurangabad 2 TE Mechanical MIT T Aurangabad

More information

Experimental Investigation of Pedal Driven Hacksaw

Experimental Investigation of Pedal Driven Hacksaw Research Inventy: International Journal of Engineering And Science Vol.4, Issue 7 (July 2014), PP 01-05 Issn (e): 2278-4721, Issn (p):2319-6483, www.researchinventy.com Experimental Investigation of Pedal

More information

VERTICAL MATERIAL HANDLING SYSTEM

VERTICAL MATERIAL HANDLING SYSTEM INTERNATIONAL JOURNAL OF MECHANICAL ENGINEERING AND TECHNOLOGY (IJMET) International Journal of Mechanical Engineering and Technology (IJMET), ISSN 0976 6340(Print), ISSN 0976 6340 (Print) ISSN 0976 6359

More information

Parametric Modeling and Finite Element Analysis of the Brake Drum Based on ANSYS APDL

Parametric Modeling and Finite Element Analysis of the Brake Drum Based on ANSYS APDL 2017 3rd International Conference on Green Materials and Environmental Engineering (GMEE 2017) ISBN: 978-1-60595-500-1 Parametric Modeling and Finite Element Analysis of the Brake Drum Based on ANSYS APDL

More information

Android Controlled Automatic Jack System for Vehicle

Android Controlled Automatic Jack System for Vehicle Android Controlled Automatic Jack System for Vehicle Sourabh Savadatti 1, Amit Doddamani 2, Vijaylaxmi N Nadagouda 3, Sahana M Konnur 4, Chetan Patil 5 U.G. Student, Department of Instrumentation Technology,

More information

P. D. Belapurkar, S.D. Mohite, M.V. Gangawane, D. D. Doltode (Department of Mechanical, M.E.S. College of Engineering, S.P. Pune University, India)

P. D. Belapurkar, S.D. Mohite, M.V. Gangawane, D. D. Doltode (Department of Mechanical, M.E.S. College of Engineering, S.P. Pune University, India) IOSR Journal of Mechanical & Civil Engineering (IOSRJMCE) e-issn: 2278-1684,p-ISSN: 2320-334X PP 12-16 www.iosrjournals.org Development and Comparison of Manual Spring Testing Machine with Universal Testing

More information

COMPARISON OF PROPELLER TYPE B-SERIES AND AU-OUTLINE GAWN SERIES FOR IMPROVING ON SUBMARINE PROPULSION PERFORMANCE USING CFD

COMPARISON OF PROPELLER TYPE B-SERIES AND AU-OUTLINE GAWN SERIES FOR IMPROVING ON SUBMARINE PROPULSION PERFORMANCE USING CFD International Journal of Mechanical Engineering and Technology (IJMET) Volume 10, Issue 03, March 2019, pp. 534-538. Article ID: IJMET_10_03_054 Available online at http://www.iaeme.com/ijmet/issues.asp?jtype=ijmet&vtype=10&itype=3

More information

Design Modification and Optimization of Trolley in an Off-Bearer Mechanism Present In Concrete Block Making Machines

Design Modification and Optimization of Trolley in an Off-Bearer Mechanism Present In Concrete Block Making Machines Design Modification and Optimization of Trolley in an Off-Bearer Mechanism Present In Concrete Block Making Machines Aravindhan. V 1, Anantha Krishnan. P 2 1,2Final Year UG Students, Dept. of Mechanical

More information

Redesign and Analysis of Automobile Wheel Rim #1 Pandit Shailesh, #2 Gajjal Shekhar

Redesign and Analysis of Automobile Wheel Rim #1 Pandit Shailesh, #2 Gajjal Shekhar ISSN 2395-1621 Redesign and Analysis of Automobile Wheel Rim #1 Pandit Shailesh, #2 Gajjal Shekhar 1 shailesh27290@gmail.com 2 shekhar.gajjal@sinhgad.edu #1234 Department of Mechanical Engineering,SavitribaiPhule

More information

Design and analysis of shock absorber using FEA tool

Design and analysis of shock absorber using FEA tool International Journal of Engineering Research and Development e-issn: 2278-067X, p-issn: 2278-800X, www.ijerd.com Volume 10, Issue 2 (February 2014), PP.22-28 Design and analysis of shock absorber using

More information

Structural Analysis of Differential Gearbox

Structural Analysis of Differential Gearbox Structural Analysis of Differential Gearbox Daniel Das.A Seenivasan.S Assistant Professor Karthick.S Assistant Professor Abstract- The main aim of this paper is to focus on the mechanical design and analysis

More information

[Vishal*et al., 5(7): July, 2016] ISSN: IC Value: 3.00 Impact Factor: 4.116

[Vishal*et al., 5(7): July, 2016] ISSN: IC Value: 3.00 Impact Factor: 4.116 IJESRT INTERNATIONAL JOURNAL OF ENGINEERING SCIENCES & RESEARCH TECHNOLOGY DESIGN AND ANALYSIS OF ALUMINUM ALLOY PISTON USING CAE TOOLS Mr. Jadhav Vishal, Dr. R.K. Jain, Mr. Yogendra S.Chauhan *M-Tech

More information

Design & Modeling of Mobile Chaff Cutter a Review

Design & Modeling of Mobile Chaff Cutter a Review Design & Modeling of Mobile Chaff Cutter a Review Vishrut Raut 1, Prof.S.M.Fulmali 2 1 Student, Mtech CAD/CAM, B.D.C.E, vishrut.raut55@gmail.com 2 Assistant professor, Mechanical Engineering, B.D.C.E,

More information

Structural Stress Analysis of Reduction Helical Gear box Casing

Structural Stress Analysis of Reduction Helical Gear box Casing International OPEN ACCESS Journal Of Modern Engineering Research (IJMER) Structural Stress Analysis of Reduction Helical Gear box Casing Sudhir Mane *, Vijay Patil ** * Department Of Mechanical Engineering,

More information

KINEMATICS OF REAR SUSPENSION SYSTEM FOR A BAJA ALL-TERRAIN VEHICLE.

KINEMATICS OF REAR SUSPENSION SYSTEM FOR A BAJA ALL-TERRAIN VEHICLE. International Journal of Mechanical Engineering and Technology (IJMET) Volume 8, Issue 8, August 2017, pp. 164 171, Article ID: IJMET_08_08_019 Available online at http://www.iaeme.com/ijmet/issues.asp?jtype=ijmet&vtype=8&itype=8

More information

Design, Analysis& Optimization of Truck chassis- Rail & Cross member

Design, Analysis& Optimization of Truck chassis- Rail & Cross member Design, Analysis& Optimization of Truck chassis- Rail & Cross member Mr. Jinto Joju Thaikkattil 1, Gayatri Patil 2 1 PGScholar, Department of Mechanical Engg., KJCOEMR, Pune, jjt7171@gmail.com 2 Assistant

More information

Design, Modelling & Analysis of Double Wishbone Suspension System

Design, Modelling & Analysis of Double Wishbone Suspension System Design, Modelling & Analysis of Double Wishbone Suspension System 1 Nikita Gawai, 2 Deepak Yadav, 3 Shweta Chavan, 4 Apoorva Lele, 5 Shreyash Dalvi Thakur College of Engineering & Technology, Kandivali

More information

6340(Print), ISSN (Online) Volume 3, Issue 3, Sep- Dec (2012) IAEME AND TECHNOLOGY (IJMET)

6340(Print), ISSN (Online) Volume 3, Issue 3, Sep- Dec (2012) IAEME AND TECHNOLOGY (IJMET) INTERNATIONAL International Journal of Mechanical JOURNAL Engineering OF MECHANICAL and Technology (IJMET), ENGINEERING ISSN 0976 AND TECHNOLOGY (IJMET) ISSN 0976 6340 (Print) ISSN 0976 6359 (Online) Volume

More information

Design and Fabrication of Eco Friendly Pedal Operated Lawn Mower for Agricultural Applications

Design and Fabrication of Eco Friendly Pedal Operated Lawn Mower for Agricultural Applications IOSR Journal of Engineering (IOSRJEN) ISSN (e): 2250-3021, ISSN (p): 2278-8719 Vol. 08, Issue 6 (June. 2018), V (V) PP 12-17 www.iosrjen.org Design and Fabrication of Eco Friendly Pedal Operated Lawn Mower

More information

DESIGN AND ANALYSIS IN MECHANISM OF TILTING MACHINE

DESIGN AND ANALYSIS IN MECHANISM OF TILTING MACHINE International Journal of Mechanical Engineering and Technology (IJMET) Volume 8, Issue 8, August 2017, pp. 282 292, Article ID: IJMET_08_08_032 Available online at http://www.ia aeme.com/ijmet/issues.asp?jtype=ijmet&vtyp

More information

Stress Analysis of Piston at Different Pressure Load

Stress Analysis of Piston at Different Pressure Load Stress Analysis of Piston at Different Pressure Load 1 PG Student, Department of Mechanical Engineering, SKNSITS, Lonavala, India 2 Professor, Department of Mechanical Engineering, SKNSITS, Lonavala, India

More information

Optimization of Four Cylinder Engine Crankshaft using FEA

Optimization of Four Cylinder Engine Crankshaft using FEA Optimization of Four Cylinder Engine Crankshaft using FEA Prasad P. Gaware 1, Prof. V.S. Aher 2 Department of Mechanical Engineering, AVCOE, Sangamner 1 Department of Mechanical Engineering, AVCOE, Sangamner

More information

A STUDY ON JACK-UP GEARBOX DESIGN FOR DRILLSHIPS

A STUDY ON JACK-UP GEARBOX DESIGN FOR DRILLSHIPS International Journal of Mechanical Engineering and Technology (IJMET) Volume 9, Issue 6, June 2018, pp. 948 959, Article ID: IJMET_09_06_107 Available online at http://www.iaeme.com/ijmet/issues.asp?jtype=ijmet&vtype=9&itype=6

More information

INVESTIGATION ON THREE-WAY DUMPING MECHANISM OF A TWO- WHEEL TRACTOR TROLLEY

INVESTIGATION ON THREE-WAY DUMPING MECHANISM OF A TWO- WHEEL TRACTOR TROLLEY 110 INVESTIGATION ON THREE-WAY DUMPING MECHANISM OF A TWO- WHEEL TRACTOR TROLLEY 1 *Shingade Mahesh, 2 Vamsi Krishna K, 3 Ajay Kumar Yadav * 1 & 3 (PG Scholar, Mechanical Engineering Department, National

More information

KEYWORDS: ANSYS, Clamping effects, Leaf spring, Pro-E. International Journal of Computational Engineering Research Vol, 03 Issue, 10

KEYWORDS: ANSYS, Clamping effects, Leaf spring, Pro-E. International Journal of Computational Engineering Research Vol, 03 Issue, 10 International Journal of Computational Engineering Research Vol, 03 Issue, 10 Leaf Spring Analysis with Eyes Using FEA B.Mahesh Babu 1, D.Muralidhar Yadav 2, N.Ramanaiah 3 1 Assistant Professor, Dr.Samuel

More information

A Literature Review and Study on 4 Wheel Steering Mechanisms

A Literature Review and Study on 4 Wheel Steering Mechanisms 2018 IJSRST Volume 4 Issue 3 Print ISSN : 2395-6011 Online ISSN: 2395-602X National Conference on Advances in Engineering and Applied Science (NCAEAS) 29 th January 2018 Organized by : Anjuman College

More information

Thermal Stress Analysis of Diesel Engine Piston

Thermal Stress Analysis of Diesel Engine Piston International Conference on Challenges and Opportunities in Mechanical Engineering, Industrial Engineering and Management Studies 576 Thermal Stress Analysis of Diesel Engine Piston B.R. Ramesh and Kishan

More information

Static Structural Analysis & Optimization of Concept Automotive A-Arm Mechanical Engineering Design

Static Structural Analysis & Optimization of Concept Automotive A-Arm Mechanical Engineering Design Static Structural Analysis & Optimization of Concept Automotive A-Arm Mechanical Engineering Design Ashish R. Pawar 1, Madhuri V. Bodke 2, Aditya R. Wankhade 3 1,3 Mechanical Engineering Department, ABMSP

More information

Keywords: Mars rover, Flange, Deformation analysis, Stress distribution

Keywords: Mars rover, Flange, Deformation analysis, Stress distribution Applied Mechanics and Materials Submitted: 2014-05-14 ISSN: 1662-7482, Vol. 574, pp 253-258 Accepted: 2014-05-15 doi:10.4028/www.scientific.net/amm.574.253 Online: 2014-07-18 2014 Trans Tech Publications,

More information

ISSN: [Patil et al., 5(10): October, 2016] Impact Factor: 4.116

ISSN: [Patil et al., 5(10): October, 2016] Impact Factor: 4.116 IJESRT INTERNATIONAL JOURNAL OF ENGINEERING SCIENCES & RESEARCH TECHNOLOGY DESIGN AND ANALYSIS OF TELESCOPIC HALFSHAFT FOR AN ALL-TERRAIN VEHICLE (ATV) Chirag Patil *, Sandeep Imale, Kiran Hiware, Sumeet

More information

Design and Development of Hydraulic Driven Mobile Air Inflator

Design and Development of Hydraulic Driven Mobile Air Inflator Available online at: http://www.ijmtst.com/vol4issue5.html International Journal for Modern Trends in Science and Technology ISSN: 2455-3778 :: Volume: 04, Issue No: 05, May 208 Design and Development

More information

Design of Boom Attachment in Backhoe Loader to Excavate Inaccessible Location

Design of Boom Attachment in Backhoe Loader to Excavate Inaccessible Location Design of Boom Attachment in Backhoe Loader to Excavate Inaccessible Location 1 Kishore Krishna M, 2 Palani P.K 1 PG Scholar, Department of Engineering Design, Government College of technology, Coimbatore.

More information