Electric Actuator/ Guide Rod Type

Transcription

1 ourtesy of M/Flodyne/Hydradyne Motion ontrol Hydraulic Pneumatic Electrical Mechanical (800) Size How to Order LEYG M B 50 S N1 Bearing type M Sliding bearing L Ball bushing bearing When [M: Sliding bearing] is selected, the maximum speed of lead [] is 0 mm/s (at no-load, horizontal mounting). The speed is also restricted with a horizontal/moment load. Refer to Model Selection on page 263. Motor mounting position Top mounting D In-line Lead Symbol LEYG LEYG LEYG/ B Motor option Without option With motor cover B With lock W With lock/motor cover When With lock or With lock/motor cover are selected for the top mounting type, the motor body will stick out of the end of the body for size / with stroke 30 mm or less. heck for interference with workpieces before selecting a model. pplicable stroke table Stroke Motor type Symbol Stroke to to Refer to the applicable stroke table. There is a limit for mounting size / top mounting types and 50 mm stroke or less. Refer to the dimensions. Guide option Without option F With grease retaining function Only available for size and sliding bearings. (Refer to onstruction on page 280.) : Standard Manufacturable stroke range Model LEYG 10 to 200 LEYG 15 to 300 LEYG/ 20 to 300 Please consult with SM for non-standard strokes as they are produced as special orders. The actuator and controller/driver are sold as a package. onfirm that the combination of the controller/driver and the actuator is correct. <heck the following before use.> heck the actuator label for model number. This matches the controller/driver. heck Parallel I/O configuration matches (NPN or PNP). Refer to the operation manual for using the products. Please download it via our website, Electric ctuator/ Guide Rod Type Series LEYG LEYG,,, Type (Servo/24 VD) Servo motor (24 VD) LEYG aution [E-compliant products] EM compliance was tested by combining the electric actuator LEYG series and the controller LE series. The EM depends on the configuration of the customer s control panel and the relationship with other electrical equipment and wiring. Therefore, conformity to the EM directive cannot be certified for SM components incorporated into the customer s equipment under actual operating conditions. s a result, it is necessary for the customer to verify conformity to the EM directive for the machinery and equipment as a whole. For the servo motor (24 VD) specification, EM compliance was tested by installing a noise filter set (LE-NF). Refer to page 9 for the noise filter set. Refer to the LE Operation Manual for installation. -Link direct input type (LEPMJ) is not E-compliant. [UL-compliant products] When conformity to UL is required, the electric actuator and controller/driver should be used with a UL1310 lass 2 power supply. Size LEYG LEYG/ ompatible controller/driver LEP6 LEP1 LEP LEPMJ LE6 For auto switches, refer to pages 243 and 244.

2 ourtesy of M/Flodyne/Hydradyne Motion ontrol Hydraulic Pneumatic Electrical Mechanical (800) Motor mounting position: Top mounting ctuator cable type1 Without cable S Standard cable2 R Robotic cable (Flexible cable)3 1 The standard cable should be used on fixed parts. For using on moving parts, select the robotic cable. 2 Only available for the motor type Step motor. 3 Fix the motor cable protruding from the actuator to keep it unmovable. For details about fixing method, refer to Wiring/ables in the Electric ctuators Precautions. I/O cable length1, ommunication plug 1 If Without controller/driver is selected for controller/driver types, I/O cable cannot be selected. Refer to page 9 (For LEP6/ LE6), page 573 (For LEP1) or page 587 (For LEP) if I/O cable is required. 2 When Pulse input type is selected for controller/driver types, pulse input usable only with differential. Only 1.5 m cables usable with open collector. 3 For the LEPMJ, only, S and T are selectable since I/O cable is not included. ompatible ontroller/driver Type Step data input type ctuator cable length [m] Without cable B Produced upon receipt of order (Robotic cable only) Refer to the specifications Note 5) on page 277. ontroller/driver mounting Screw mounting D DIN rail mounting DIN rail is not included. Order it separately. Motor mounting position: In-line ontroller/driver type1 Without controller/driver 6N LEP6/LE6 NPN 6P (Step data input type) PNP 1N LEP12 NPN 1P (Programless type) PNP 1 For details about controller/driver and compatible motor, refer to the compatible controller/driver below. 2 Only available for the motor type Step motor. 3 Not applicable to E. 4 When pulse signals are open collector, order the current limiting resistor (LE-P-R-) on page 587 separately. Use of auto switches for the guide rod type LEYG series Insert the auto switch from the front side with rod (plate) sticking out. For the parts hidden behind the guide attachment (Rod stick out side), the auto switch cannot be fixed. Please consult with SM when using auto switch on the rod stick out side, as it is produced as a special order. Step data input type -Link direct input type Programless type Pulse input type Series LEP6 LE6 LEPMJ LEP1 LEP Features Without cable (Without communication plug connector) m 3 3 m2 5 5 m2 S Straight type communication plug connector3 T T-branch type communication plug connector3 ompatible motor (Servo/24 VD) Value (Step data) input Standard controller Servo motor (24 VD) Electric ctuator/guide Rod Type Series LEYG Step Motor (Servo/24 VD) Servo Motor (24 VD) -Link direct input apable of setting up operation (step data) without using a P or teaching box (Servo/24 VD) Operation by pulse signals Maximum number of step data 64 points 14 points Power supply voltage 24 VD Reference page Page 1 Page 1 Page 591 Page 567 Page 581 MJ N P LEPMJ2 3 (-Link direct input type) LEP2 4 (Pulse input type) NPN PNP 276 LEFS LEFB LEJS LEJB LEL LEM LEY LEYG LES LESH LEPY LEPS LER LEH LEY-5 11-LEFS 11-LEJS - LT3 Motorless LEYM LEYU LESS-T LES LE

3 ourtesy of M/Flodyne/Hydradyne Motion ontrol Hydraulic Pneumatic Electrical Mechanical (800) Series LEYG Step Motor (Servo/24 VD) Servo Motor (24 VD) Specifications Step Motor (Servo/24 VD) Model LEYG M L LEYG M L LEYG M L LEYG M L ctuator specifications Electric specifications Lock unit specifications Stroke Note 1) 30, 50, 100, 150, , 50, 100, 150, 200, 0, , 50, 100, 150, 200, 0, , 50, 100, 150, 200, 0, 300 Work load [kg ] Note 2) Horizontal (LEP6, LEP1, LEPMJ) cceleration/deceleration at 3000 [mm/s 2 ] cceleration/deceleration at 2000 [mm/s 2 ] cceleration/deceleration Horizontal at 3000 [mm/s 2 ] (LEP) cceleration/deceleration at 2000 [mm/s 2 ] cceleration/deceleration Vertical at 3000 [mm/s 2 ] Pushing force [N] Note 3) 4) 5) 14 to to to to to to to to to to to to 1058 Speed LEP6/LEP1/LEPMJ 12 to to to to to to to 0 4 to 1 18 to to 0 5 to 1 24 to 500 [mm/s] Note 5) LEP 12 to 0 6 to 1 24 to to to 75 Max. acceleration/deceleration [mm/s 2 ] 3000 Pushing speed [mm/s] Note 6) 50 or less 35 or less 30 or less 30 or less Positioning repeatability 0.02 Lost motion Note 7) 0.1 or less Screw lead Impact/Vibration resistance [m/s 2 ] Note 8) 50/20 ctuation type Ball screw + Belt (LEYG), Ball screw (LEYGD) Guide type Sliding bearing (LEYGM), Ball bushing bearing (LEYGL) Operating temp. range [] 5 to Operating humidity range [%RH] 90 or less (No condensation) Motor size Motor type (Servo/24 VD) Encoder Incremental /B phase (800 pulse/rotation) Rated voltage [V] 24 VD 10% Power consumption [W] Note 9) Standby power consumption when operating [W] Note 10) Max. instantaneous power consumption [W] Note 11) Type Note 12) Non-magnetizing lock Holding force [N] Power consumption [W] Note 13) Rated voltage [V] 24 VD 10% Note 1) Please consult with SM for non-standard strokes as they are produced as special orders. Note 2) Horizontal: n external guide is necessary to support the load (Friction coefficient of guide: 0.1 or less). The actual work load and transfer speed change according to the condition of the external guide. lso, speed changes according to the work load. heck Model Selection on pages 2 and 266. Vertical: Speed changes according to the work load. heck Model Selection on pages 2 and 266. Set the acceleration/deceleration values to be 3000 [mm/s 2 ] or less. Note 3) Pushing force accuracy is 20% (F.S.). Note 4) The pushing force values for LEYG is 35% to 85%, for LEYG is 35% to %, for LEYG is 35% to 85% and for LEYG is 35% to %. The pushing force values change according to the duty ratio and pushing speed. heck Model Selection on page 268. Note 5) The speed and force may change depending on the cable length, load and mounting conditions. Furthermore, if the cable length exceeds 5 m, then it will decrease by up to 10% for each 5 m. (t 15 m: Reduced by up to 20%) When [M: Sliding bearing] is selected, the maximum speed of lead [] is 0 mm/s (at no-load, horizontal mounting). The speed is also restricted with a horizontal/moment load. Refer to Model Selection on page 263. Note 6) The allowable speed for the pushing operation. Note 7) reference value for correcting an error in reciprocal operation. Note 8) Impact resistance: No malfunction occurred when it was tested with a drop tester in both an axial direction and a perpendicular direction to the lead screw. (Test was performed with the actuator in the initial state.) Vibration resistance: No malfunction occurred in a test ranging between 45 to 2000 Hz. Test was performed in both an axial direction and a perpendicular direction to the lead screw. (Test was performed with the actuator in the initial state.) Note 9) The power consumption (including the controller) is for when the actuator is operating. Note 10) The standby power consumption when operating (including the controller) is for when the actuator is stopped in the set position during the operation. Except during the pushing operation. Note 11) The maximum instantaneous power consumption (including the controller) is for when the actuator is operating. This value can be used for the selection of the power supply. Note 12) With lock only Note 13) For an actuator with lock, add the power consumption for the lock. 277

4 ourtesy of M/Flodyne/Hydradyne Motion ontrol Hydraulic Pneumatic Electrical Mechanical (800) Specifications Servo Motor (24 VD) Model LEYG M L LEYG M L ctuator specifications Electric specifications Lock unit specifications Stroke Note 1) 30, 50, 100, 150, , 50, 100, 150, 200, 0, 300 Horizontal Work load [kg] Note 2) Weight cceleration/deceleration at 3000 [mm/s 2 ] cceleration/deceleration Vertical at 3000 [mm/s 2 ] Weight: Motor Top Mounting Type Weight: In-line Motor Type dditional Weight [kg] Size Lock Motor cover Lock/Motor cover Pushing force [N] Note 3) 4) to to to to to to 130 Speed [mm/s] 1 to to 0 1 to 1 2 to to 0 1 to 1 Max. acceleration/deceleration [mm/s 2 ] 3000 Pushing speed [mm/s] Note 5) 50 or less 35 or less Positioning repeatability 0.02 Lost motion Note 6) 0.1 or less Screw lead Impact/Vibration resistance [m/s 2 ] Note 7) 50/20 ctuation type Ball screw + Belt (LEYG), Ball screw (LEYGD) Guide type Sliding bearing (LEYGM), Ball bushing bearing (LEYGL) Operating temp. range [] 5 to Operating humidity range [%RH] 90 or less (No condensation) Motor size Motor output [W] Motor type Servo motor (24 VD) Encoder Incremental /B (800 pulse/rotation)/z phase Rated voltage [V] 24 VD 10% Power consumption [W] Note 8) 86 Standby power consumption when operating [W] Note 9) 4 (Horizontal)/6 (Vertical) 4 (Horizontal)/12 (Vertical) Max. instantaneous power consumption [W] Note 10) Type Note 11) Non-magnetizing lock Holding force [N] Power consumption [W] Note 12) Rated voltage [V] 24 VD 10% Electric ctuator/guide Rod Type Series LEYG Step Motor (Servo/24 VD) Servo Motor (24 VD) Note 1) Please consult with SM for non-standard strokes as they are produced as special orders. Note 2) Horizontal: n external guide is necessary to support the load (Friction coefficient of guide: 0.1 or less). The actual work load and transfer speed change according to the condition of the external guide. Vertical: heck Model Selection on page 267 for details. Set the acceleration/deceleration values to be 3000 [mm/s 2 ] or less. Note 3) Pushing force accuracy is 20% (F.S.). Note 4) The pushing force values for LEYG is 50% to 95% and for LEYG is 50% to 95%. The pushing force values change according to the duty ratio and pushing speed. heck Model Selection on page 268. Note 5) The allowable speed for the pushing operation. Note 6) reference value for correcting an error in reciprocal operation. Note 7) Impact resistance: No malfunction occurred when it was tested with a drop tester in both an axial direction and a perpendicular direction to the lead screw. (Test was performed with the actuator in the initial state.) Vibration resistance: No malfunction occurred in a test ranging between 45 to 2000 Hz. Test was performed in both an axial direction and a perpendicular direction to the lead screw. (Test was performed with the actuator in the initial state.) Note 8) The power consumption (including the controller) is for when the actuator is operating. Note 9) The standby power consumption when operating (including the controller) is for when the actuator is stopped in the set position during the operation. Except during the pushing operation. Note 10) The maximum instantaneous power consumption (including the controller) is for when the actuator is operating. This value can be used for the selection of the power supply. Note 11) With lock only Note 12) For an actuator with lock, add the power consumption for the lock. Model LEYGM LEYGM LEYGM Stroke weight [kg] Servo motor Model LEYGL LEYGL LEYGL Stroke weight [kg] Servo motor Model LEYGM LEYGL Stroke weight [kg] Servo motor Model LEYGM LEYGM LEYGM Stroke weight [kg] Servo motor Model LEYGL LEYGL LEYGL Stroke weight [kg] Servo motor Model LEYGM LEYGL Stroke weight [kg] Servo motor 278 LEFS LEFB LEJS LEJB LEL LEM LEY LEYG LES LESH LEPY LEPS LER LEH LEY-5 11-LEFS 11-LEJS - LT3 Motorless LEYM LEYU LESS-T LES LE

5 ourtesy of M/Flodyne/Hydradyne Motion ontrol Hydraulic Pneumatic Electrical Mechanical (800) Series LEYG Step Motor (Servo/24 VD) Servo Motor (24 VD) onstruction Motor top mounting type Motor top mounting type With lock/motor cover In-line motor type In-line motor type With lock/motor cover 279

6 ourtesy of M/Flodyne/Hydradyne Motion ontrol Hydraulic Pneumatic Electrical Mechanical (800) onstruction LEYGM LEYGL omponent Parts No. Description Material Note 1 Body luminum alloy nodized 2 Ball screw (shaft) lloy steel 3 Ball screw nut Resin/lloy steel 4 Piston luminum alloy 5 Piston rod Stainless steel Hard chrome plating 6 Rod cover luminum alloy 7 Housing luminum alloy 8 Rotation stopper POM 9 Socket Free cutting carbon steel Nickel plating 10 onnected shaft Free cutting carbon steel Nickel plating 11 Bushing Lead bronze cast 12 Bumper Urethane 13 Bearing 14 Return box luminum die-cast oating 15 Return plate luminum die-cast oating Magnet 17 Wear ring holder Stainless steel Stroke 101 mm or more 18 Wear ring POM Stroke 101 mm or more 19 Screw shaft pulley luminum alloy 20 Motor pulley luminum alloy 21 Belt 22 Bearing stopper luminum alloy 23 Parallel pin Stainless steel 24 Seal NBR Retaining ring Steel for spring Phosphate coated 26 Motor 27 Motor cover Synthetic resin Only With motor cover 28 Grommet Synthetic resin Only With motor cover Electric ctuator/guide Rod Type Series LEYG Step Motor (Servo/24 VD) Servo Motor (24 VD) LEYG M: 50st or less LEYG M: Over 50st LEYGL: 30st or less LEYG L: 100st or less LEYGL: Over 30st, 100st or less LEYG L: Over 100st Replacement Parts/Belt No. Size Order no. LE-D LE-D-2-2, LE-D-2-3 When grease retaining function selected LEYG M B-F: 50st or less LEYG M B-F: Over 50st Note) Felt material is inserted to retain grease at the sliding part of the sliding bearing. This lengthens the life of the sliding part, but does not guarantee it permanently. No. Description Material Note 29 Guide attachment luminum alloy nodized 30 Guide rod arbon steel 31 Plate luminum alloy nodized Plate mounting cap screw arbon steel Nickel plating 33 Guide cap screw arbon steel Nickel plating 34 Sliding bearing 35 Lube-retainer Felt 36 Holder Resin 37 Retaining ring Steel for spring Phosphate coated 38 Ball bushing 39 Spacer luminum alloy hromated Motor block luminum alloy nodized 41 Motor adapter luminum alloy nodized/ley, only 42 Hub luminum alloy 43 Spider NBR 44 Motor cover with lock luminum alloy Only With lock/motor cover 45 over support luminum alloy Only With lock/motor cover Replacement Parts/Grease Pack pplied portion Piston rod Guide rod Order no. GR-S-010 (10 g) GR-S-020 (20 g) pply grease on the piston rod periodically. Grease should be applied at 1 million cycles or 200 km, whichever comes first. 280 LEFS LEFB LEJS LEJB LEL LEM LEY LEYG LES LESH LEPY LEPS LER LEH LEY-5 11-LEFS 11-LEJS - LT3 Motorless LEYM LEYU LESS-T LES LE

7 ourtesy of M/Flodyne/Hydradyne Motion ontrol Hydraulic Pneumatic Electrical Mechanical (800) Series LEYG Step Motor (Servo/24 VD) Servo Motor (24 VD) Dimensions: Motor Top Mounting Note 1) Range within which the rod can move when it returns to origin. Make sure a workpiece mounted on the rod does not interfere with the work pieces and facilities around the rod. Note 2) Position after return to origin. Note 3) [ ] for when the direction of return to origin has changed. Note 4) Through holes cannot be used for size / with 50 mm stroke or less. EV V J Section U T EH ød 4 x O through ø H9 depth Q S ødb Stroke end [Origin] Note 3) Rod operating range Note 1) [2] 2 (F) Y Z 0.5 F FB Stroke Note 4) (0.5) 4 x øg through W L + Stroke Origin Note 2) [Stroke end] B + Stroke + Stroke V VB B 20 Y K P G M E EB 0.5 FB Section Y details 4 x N thread depth NB LEYGL (Ball bushing bearing) ø H9 depth 4 x O thread depth OB LEYGM (Sliding bearing) Standard stroke: 50, 100, 200 Standard stroke: 30, 50, x N thread depth N Size Stroke range L DB Size Stroke range L DB 90st or less 75 64st or less st or more, 200st or less 105 st or more, 90st or less st or less 91 91st or more, 200st or less st or more, 190st or less st or less st or more, 300st or less st or more, 185st or less Section 114st or less st or more, 300st or less 138 (0.5) Section 115st or more, 190st or less st or less 74 WB 191st or more, 300st or less 134 st or more, 180st or less 107 Z W 181st or more, 300st or less 144 LEYGM, LEYGL ommon W + Stroke H9 Size Stroke range B D E EB EH EV F FB F G G H J K M N NB N st or more, 100st or less M4 x st or more, 200st or less st or more, 100st or less st or more, 124st or less M5 x st or more, 200st or less st or more, 300st or less st or more, 100st or less st or more, 124st or less M6 x st or more, 200st or less st or more, 300st or less 102 Servo motor Size Stroke range O OB P Q S T U V V VB V VB W WB W B Y Z 19 st or more, 100st or less M5 x st or more, 200st or less st or more, 100st or less 101st or more, 124st or less M6 x st or more, 200st or less st or more, 100st or less 101st or more, 124st or less M6 x st or more, 200st or less st or more, 100st or less 101st or more, 124st or less M6 x st or more, 200st or less M H

8 ourtesy of M/Flodyne/Hydradyne Motion ontrol Hydraulic Pneumatic Electrical Mechanical (800) Dimensions: In-line Motor Note 1) Range within which the rod can move when it returns to origin. Make sure a workpiece mounted on the rod does not interfere with the workpieces and facilities around the rod. Note 2) Position after return to origin. Note 3) [ ] for when the direction of return to origin has changed. Section EV J U T EH 4 x O through Q S LEYGM, LEYGL ommon P ød ødb LEYGL (Ball bushing bearing) Standard stroke: 50, 100, 200 Size Stroke range L DB 0.5 F FB ø H9 depth (0.5) Origin Note 2) Stroke end Rod operating range Note 1) [Origin] Note 3) [Stroke end] [2] Stroke 2 Y (F) Z ø H9 depth Electric ctuator/guide Rod Type Series LEYG Step Motor (Servo/24 VD) Servo Motor (24 VD) 4 x øg W through L + Stroke B + Stroke + Stroke YD 4 x O thread depth OB B 2 able length 300 VB K V E EB 0.5 FB Section Y details G H LEYGM (Sliding bearing) Standard stroke: 30, 50, x N thread depth N Size Stroke range L DB 90st or less 75 64st or less st or more, 200st or less 105 st or more, 90st or less st or less 91 91st or more, 200st or less st or more, 190st or less st or less st or more, 300st or less 133 Section 60st or more, 185st or less st or less 97.5 (0.5) Section 186st or more, 300st or less st or more, 190st or less WB 54st or less st or more, 300st or less 134 Z W st or more, 180st or less 107 W + Stroke H9 181st or more, 300st or less 144 Size Stroke range Servo motor B D E EB EH EV F FB F G G H J K N N st or more, 100st or less M4 x st or more, 200st or less st or more, 100st or less st or more, 124st or less M5 x st or more, 200st or less st or more, 300st or less st or more, 100st or less st or more, 124st or less M6 x st or more, 200st or less st or more, 300st or less st or more, 100st or less st or more, 124st or less M6 x st or more, 200st or less st or more, 300st or less 102 Size Stroke range O OB P Q S T U V Servo motor VB W WB W B YD Z 19 st or more, 100st or less M5 x st or more, 200st or less st or more, 100st or less 101st or more, 124st or less M6 x st or more, 200st or less st or more, 100st or less 101st or more, 124st or less M6 x st or more, 200st or less st or more, 100st or less 101st or more, 124st or less M6 x st or more, 200st or less LEFS LEFB LEJS LEJB LEL LEM LEY LEYG LES LESH LEPY LEPS LER LEH LEY-5 11-LEFS 11-LEJS - LT3 Motorless LEYM LEYU LESS-T LES LE

9 ourtesy of M/Flodyne/Hydradyne Motion ontrol Hydraulic Pneumatic Electrical Mechanical (800) Series LEYG Step Motor (Servo/24 VD) Servo Motor (24 VD) Dimensions Motor top mounting type With motor cover: LEYG B- onnector Size T2 2 T2 Servo motor Motor cover material: Synthetic resin Stroke Motor cable (2 x ø5) In-line motor type With motor cover: LEYG D B- Size Stroke range T2 2 L H V 100st or less st or more, 200st or less st or less st or more, 300st or less st or less 2 101st or more, 300st or less st or less 4 101st or more, 300st or less L L V T2 able length 0 H With lock: LEYG B-B onnector Lock cable Motor cable Lock cable Motor cable Servo motor 15 Size Servo motor W W Servo motor With lock: LEYG D B-B onnector Size Stroke range Motor cable (2 x ø5) Lock cable (ø3.5) W Lock cable (ø3.5) Motor cable (2 x ø5) 2 VB + Stroke able length 0 able length 0 Servo motor Servo motor VB 100st or less st or more, 200st or less st or less st or more, 300st or less st or less st or more, 300st or less st or less st or more, 300st or less 3.9

10 ourtesy of M/Flodyne/Hydradyne Motion ontrol Hydraulic Pneumatic Electrical Mechanical (800) Dimensions Motor top mounting type With lock/motor cover: LEYG -W B able length 0 Motor cable (2 x ø5) Size T Lock cable (ø3.5) T2 able length 0 Electric ctuator/guide Rod Type Series LEYG Step Motor (Servo/24 VD) Servo Motor (24 VD) In-line motor type With lock/motor cover: LEYG D -W B able length 0 Lock cable (ø3.5) Motor cable (2 x ø5) 2 + Stroke Size Stroke range T2 2 L H V 100st or less st or more, 300st or less st or less 0 101st or more, 300st or less st or less st or more, 300st or less st or less st or more, 300st or less 7 H T2 able length 0 L L V LEFS LEFB LEJS LEJB LEL LEM LEY LEYG LES LESH LEPY LEPS LER LEH LEY-5 11-LEFS 11-LEJS - LT3 Motorless LEYM LEYU LESS-T LES LE

11 ourtesy of M/Flodyne/Hydradyne Motion ontrol Hydraulic Pneumatic Electrical Mechanical (800) Series LEYG Step Motor (Servo/24 VD) Servo Motor (24 VD) Support Block Guide for support block application When the stroke exceeds 100 mm and the mounting orientation is horizontal, the body will be bent. Mounting the support block is recommended. (Please order it separately from the models shown below.) Support Block Model LEYG S 0 (0.5) W + Stroke Size 0 For size 0 For size 0 For size, aution Do not install the body using only a support block. The support block should be used only for support. ST Support block Body mounting screw 2 x O thread depth OB 2 x øg through EB G Support block Size Model Stroke range EB G G O OB ST W LEYG-S0 100st or less M5 x st or more, 200st or less LEYG-S0 100st or less M6 x st or more, 300st or less st or less 75 LEYG-S0 101 (5.4) (50.3) M6 x st or more, 300st or less Two body mounting screws are included with the support block. The through holes of the LEYG-S0 cannot be used. Use taps on the bottom. 285