Severe Duty Water Cannon Styles 3491 & 3492 Electric & Hydraulic
|
|
- Mervin Fleming
- 5 years ago
- Views:
Transcription
1 Severe Duty Water Cannon Styles 3491 & 3492 Electric & Hydraulic Disassembly/Assembly Service Repair Procedure australian only Tools Required: 3/16 Allen Key 5/16 Allen Key 5/16 Socket or Spanner 5/32 Allen Key 1/2 Socket or Spanner Mobilith SHC 460 Synthetic Grease Loctite Marker Pen Disassembly Procedure: 1. Isolate Power Source from Water Cannon 2. Disconnect hydraulic hoses from nozzle & motors. (If using electric monitor, disconnect electrical connections) (i) 2 from Nozzle (ii) 2 from each Hydraulic Motor 3. Remove Nozzle Style 3492 Shown 4. Remove Vertical Rotating Joint from upstream waterway (4-5/16 stainless hex head cap screws) Item / #
2 5. Remove Motor & Gearbox Housing assembly from shaft. (4-5/32 socket head cap screws) Item / #41 6. Remove Worm Drive from Vertical Rotating Joint (4-5/16 socket head cap screws) 7. Mark opposing side of Vertical Rotating Joint for easy reassembly 8. Remove Rotational Stops (2-1/2 hex head cap screws) Item / # 8 Figure 1 Stop Plug NOTE: Steel stops have a double hex head see Figure 1. Plastic plugs have a single hex head. You do not need to remove the plastic plug ( / #9), only the steel stops. 2
3 9. Remove downstream waterway flange from Vertical Rotating (4-5/16 socket head cap screws. Item / # 48. Also, remove 2 of Polymer bearing. Item / # Remove 3 x 3/16 (locking pins) socket head cap screws from Worm Gear assembly. Item / # Separate Worm Gear from waterway. Item / # 4 Assembly Procedure: 1. Properly clean & regrease all parts as necessary 2. Replace both motor subassemblies and worn parts as necessary 3. Recommend replacement of Polymer Bearings and Worm Gear. Item - ( / # 44 Bearing) ( / # 4 Worm Gear) Polymer Bearing 3
4 4. Lubricate both main waterway where Worm Gear is positioned along with o-rings with Mobilith SHC 460 Synthetic Grease. 5. Reinstall Worm Gear into position taking note to match the 3 x 3/16 (locking pins) socket head cap screws from Worm Gear assembly. Item / # 51 Please Note: 3/16 locking pins should be prepared with Teflon pipe sealant tape prior to assembly. 6. Lubricate Worm Drive spline along with Rotation slot in Vertical Rotating Joint prior to assembly. 7. Lubricate Bearings prior to carefully reinstalling and securing Worm Gear into Vertical Rotating Joint. Hint: Install small amount of Loctite 222 on 4-5/16 socket head cap screws prior to assembly. 4
5 8. Reinstall Rotational Stops (2-1/2 hex head cap screws) in correct position or to required travel length (adjustable). Item / #8 9. Install Vertical Rotating Joint to upstream waterway. Install small amount of Loctite 222 on 4-5/16 socket head screws prior to assembly. 10. Reinstall Nozzle 11. Re-connect power source 12. Test movement of water cannon using the joystick in all directions to ensure full movement. 13. Check for leaks from waterway Your Akron Water Cannon is now Ready for Use! 5
6 Hydraulic Cannon 6
7 3492 Hydraulic Severe-Duty Monitor item no. description part number quantity 1 OUTLET ELBOW MIDDLE ELBOW INLET 2.5 NPT WORM GEAR JOINT CAP NAIL GRIP ID PLATE STOP PIN PLUG SCREW SOC HD CAP 1/4-20 X 7/ O-RING POLYMER BEARING O-RING O-RING SCREW HEX HD CAP ST STL 5/16-18 X 7/ STUD JOINT HOUSING NIPPLE 2.5 NPT FLANGE HYDRAULIC MOTOR & GEAR SUB ASSEMBLY Complete Assembly MON SD S/A 3FLG X 2.5NH, HYDRAULIC, SS, BLK, SPC SUB ASSEMBLY & ACCESSORIES PARTS LIST RAMPAGE HYDRAULIC NZ, SD, 2.5NH, INCLDS NEEDLE VALVE AKROFOAM HYDRAULIC NZ, SD, 2.5NH, INCLDS NEEDLE VALVE NEEDLE VALVE WITH 1/8 NPT F THREAD
8
9 3492 Hydraulic Motor item no. description part number quantity 11 GASKET HYDRAULIC MOTOR SHAFT HOUSING O-RING SOCKET HEAD CAP SCREW 1/4-28X5/8 STSTL RETAINING RING ROLLER BEARING BELLVILLE SPRING THRUST WASHER THRUST BEARING WORM SHAFT HOUSING KEY ROLLER BEARING O-RING MOTOR ADAPTER O-RING SOCKET HEAD CAP SCREW X 3/4 ST STL RETAINING RING LABEL
10 Electric Cannon
11 3491 Severe-Duty Monitor item no. description part number quantity 1 OUTLET ELBOW MIDDLE ELBOW INLET WORM GEAR JOINT CAP NAIL GRIP ID PLATE STOP PIN PLUG MAGNET SCREW SOC HD CAP 1/4-20 X 7/8 STSTL O-RING POLYMER BEARINGS O-RING O-RING SCREW HEX HD CAP 5/16-18 X 7/ SCREW SOC HD CAP 10-24X WIRING HARNESS (NOT SHOWN) STUD JOINT HOUSING NIPPLE 2.5NPT 6 LONG STSTL COMP FLG 3 150# FLAT FACE STSTL W/ 2.5 NPT MOTOR S/A GEAR, CONN, 12V, BLACK MOTOR S/A GEAR, CONN, 24V, BLACK Complete Assembly MON SD S/A 3FLG X 2.5NH, 24V, SS, BLK, SPC SUB ASSEMBLY & ACCESSORIES PARTS LIST BOX LOGIC W/CONNECTORS, 12/24V FF, MINING MON BOARD PC 12/24V W/LMT TRAVEL EA REPAIR / 6 METRE WIRING HARNESS WITH IP67 DEUTSCH PLUGS / 10 METRE WIRING HARNESS WITH IP67 DEUTSCH PLUGS / 12 METRE WIRING HARNESS WITH IP67 DEUTSCH PLUGS RAMPAGE ELECT NZ, SD, 2.5NH, 12V, GPM RAMPAGE ELECT NZ, SD, 2.5NH, 24V, GPM NZ AKROFOAM 24V, 2.5NH, IP67 DEUTSCH PLUG, NZ BOOT, GPM JOYSTICK FOR MINING MONITOR
12 NOTES: USE MOBILITH SHC 460 ON ALL ASSEMBLY USE PERMABOND LM113 OR LOCTITE ASSEMBLY USE LUBRIPLATE LOW-TEMP ASSEMBLY ASSEMBLE RETAINING RING (ITEM 62) WITH SHARP CORNERS AWAY FROM MOTOR ADAPTER (ITEM 40) 3491 Electric Motor Assembly
13 3491 Severe-Duty Motor item no. description part number quantity 15 MOTOR WITH GEAR AND CONNECTOR 12V MOTOR WITH GEAR AND CONNECTOR 24V O-RING O-RING HOUSING O-RING SCREW SOC HD CAP W/PATCH 6-32X1/ RIVET PLANET GEAR CARRIER INTERNAL GEAR CARRIER PLATE ROLL PIN RETAINING RING ROLLER BEARING BELLEVILLE SPRING THRUST WASHER THRUST BEARING WORM SHAFT KEY ROLLER BEARING SPRING PIN O-RING ADAPTER O-RING SCREW SOC HD CAP 6-32 X 1 3/8 LG STSTL RETAINING RING
14 Australian Severe-Duty Water Cannon Preventive Maintenance Program Sheet Beginning Date Ending Date Serial Number Model Number Timeline: 6 months 12 months 18 months 24 months 30 month 36 months Task: Remove Motor Subassembly and inspect and evaluate grease of Worm. (See Below) * * * Worm Gear (See Below) * * * ** Order Preventative Maintenance Kit. * * * Remove Motor Subassembly and inspect and evaluate grease of ** Preventative Maintenance Kit may be ordered prior to schedule depending on grease evaluation throughout preventative maintenance cycle. Worm Grease color evaluation: Color: Action: Electric Preventative Maintenance Kit Hydraulic Preventative Maintenance Kit Red Reddish Brown Black Clean grease from worm. Inspect for metal shavings. If none, apply generous amount of grease to worm; component ready for reinstallation. Clean grease from worm. Inspect for metal shavings. If none, apply generous amount of grease to worm. Component ready for service. Component needs overhaul. Preventative Maintenance Kit required. Worm Gear Grease color evaluation: Color: Red Reddish Brown Black Action: Clean grease from worm gear. Inspect for metal shavings. If none, apply generous amount of grease to worm gear; component ready for reinstallation. Clean grease from worm gear. Inspect for metal shavings. If none, apply generous amount of grease to worm gear. Component ready for service. Component needs overhaul. Preventative Maintenance Kit required. 14
15 PRODUCT WARNINGS WARNING: WARNING: WARNING: WARNING: WARNING: WARNING: WARNING: Aim the Severe Duty Water Cannon in a safe direction before pumping water through it. If any tags or bands are worn or damaged and cannot be easily read, they should be replaced. Disconnect power and disable flow before maintenance. Keep all personnel out from the front of the outlet of the monitor when the water source is attached. Dangerous flow velocities can cause serious injury. The Severe Duty Water Cannon contains moving parts. Keep hand, finger and objects away from pinch points. Not designed for explosive environments. Exceeding the maximum pressure and flow of the monitor or nozzle may cause damage. WARRANTY AND DISCLAIMER We warrant Akron Brass products for a period of one (1) year after purchase against defects in materials or workmanship. Akron Brass will repair or replace product which fails to satisfy this warranty. Repair or replacement shall be at the discretion of Akron Brass. Products must be promptly returned to Akron Brass for warranty service. We will not be responsible for: wear and tear, any improper installation, use, maintenance or storage: negligence of the owner or user; repair or modification after delivery; failure to follow our instructions or recommendations; or anything else beyond our control. WE MAKE NO WARRANTIES, EXPRESS OR IMPLIED, OTHER THAN THOSE INCLUDED IN THIS WARRANTY STATEMENT, AND WE DISCLAIM ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE. Further, we will not be responsible for any consequential, incidental or indirect damages (including, but not limited to, any loss of profits) from any cause whatsoever. No person has authority to change this warranty. GENERAL INSTRUCTIONS For use with water or standard fire fighting foams only. After use with foam, flush with fresh water. Drain the Severe Duty Water Cannon and nozzle after use to prevent freeze damage in cold weather. Ensure that the thread in the nozzle swivel matches the thread on the Severe Duty outlet. Do not overtighten the nozzle onto the Severe Duty Water Cannon. Do not install shutoffs on the outlet of the Severe Duty. MAINTENANCE INSTRUCTIONS Your Severe Duty Water Cannon and nozzle should be inspected prior to and after each use, to ensure it is in good operating condition. The Water Cannon joints were greased and sealed at assembly, there is no greasing to be done while in use. SITUATIONS THAT MAY CAUSE IRRERPAIRABLE DAMAGE Operating above maximum rated pressure and flow. Not draining, and allowing water to freeze inside. Prolonged exposure to temperatures above 130 F (54 C), or below -25 F (-32 C). Having the nozzle hit a fixed object during operating or transportation. Also there are many tell tale signs that indicate repair is in order, such as: Controls that are either inoperable or difficult to operate. Excessive wear. Poor discharge performance. Water leaks. If any of the above situations are encountered, the Severe Duty should be taken out of service, repaired, and tested by a qualified technician before placing it back in service 15
16 PHONE: or I FAX: or I revised: 9/08 WARRANTY AND DISCLAIMER: We warrant Akron Brass products for a period of five (5) years after purchase against defects in materials or workmanship. Akron Brass will repair or replace product which fails to satisfy this warranty. Repair or replacement shall be at the discretion of Akron Brass. Products must be promptly returned to Akron Brass for warranty service. ISO 9001 REGISTERED COMPANY We will not be responsible for: wear and tear; any improper installation, use, maintenance or storage; negligence of the owner or user; repair or modification after delivery; damage; failure to follow our instructions or recommendations; or anything else beyond our control. WE MAKE NO WARRANTIES, EXPRESS OR IMPLIED, OTHER THAN THOSE INCLUDED IN THIS WARRANTY STATEMENT, AND WE DISCLAIM ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE. Further, we will not be responsible for any consequential, incidental or indirect damages (including, but not limited to, any loss of profits) from any cause whatsoever. No person has authority to change this warranty. Premier Farnell Corporation All rights reserved. No portion of this can be reproduced without the express written consent of Premier Farnell Corporation.
Severe Duty Water Cannon Styles 3491 & 3492 Electric & Hydraulic
Tools Required: 3 / 16 Allen Key 5 / 16 Allen Key 5 / 16 Socket or Spanner 5 / 32 Allen Key 1 / 2 Socket or Spanner Mobilith SHC 460 Synthetic Grease Loctite Marker Pen Severe Duty Water Cannon Styles
More informationThe following is intended to provide the basic instructions for installation, operating and maintenance of the Severe Duty Monitor.
STYLE 3492 Severe Duty Hydraulic Monitor INSTALLATION, OPERATING and MAINTENANCE INSTRUCTIONS The following is intended to provide the basic instructions for installation, operating and maintenance of
More informationSTYLE 3491 Severe Duty Electric Mining Water Cannon INSTALLATION, AND OPERATING INSTRUCTIONS
STYLE 349 Severe Duty Electric Mining Water Cannon INSTALLATION, AND OPERATING INSTRUCTIONS Australian Only The following is intended to provide the basic instructions for installation, operating and maintenance
More informationSTYLE 3462 FORESTRY BUMPER MONITOR INSTALLATION, OPERATING and MAINTENANCE INSTRUCTIONS
STYLE 3462 FORESTRY BUMPER MONITOR INSTALLATION, OPERATING and MAINTENANCE INSTRUCTIONS The following is intended to provide the basic instructions for installation, operating and maintenance of the 3462
More informationSTYLE 3463 FireFox. With Position Feedback Potentiometer
STYLE 3463 FireFox INSTALLATION, OPERATING and MAINTENANCE INSTRUCTIONS With Position Feedback Potentiometer The following is intended to provide the basic instructions for installation, operating and
More information( Versions Available)
STYLE 494 ELECTRIC LADDER PIPE INSTALLATION, OPERATING AND MAINTENANCE INSTRUCTIONS ( Versions Available) The following is intended to provide the basic instructions for installation, operating and maintenance
More informationSTYLE 5148 MERCURYMASTER OSCILLATING NOZZLE INSTALLATION, OPERATING, AND MAINTENANCE INSTRUCTIONS
STYLE 5148 MERCURYMASTER OSCILLATING NOZZLE INSTALLATION, OPERATING, AND MAINTENANCE INSTRUCTIONS The following is intended to provide the basic instructions for installation, operation, and maintenance.
More informationSTYLE 5148 MERCURYMASTER OSCILLATING NOZZLE INSTALLATION, OPERATING, AND MAINTENANCE INSTRUCTIONS
STYLE 5148 MERCURYMASTER OSCILLATING NOZZLE INSTALLATION, OPERATING, AND MAINTENANCE INSTRUCTIONS The following is intended to provide the basic instructions for installation, operation, and maintenance.
More information: 1250 gpm in the deck mode : 800 gpm while operating in the ground base - Dual Inlet : 1000 gpm while operating in the ground base - Single Inlet
APOLLO HI-RISER MONITOR STYLE 3433/3431 INSTALLATION, OPERATING, AND MAINTENANCE INSTRUCTIONS The following is intended to provide the basic instructions for installation, operation and maintenance of
More informationELECTRIC ACTUATOR AND CONTROLLER FOR AKRON BUTTERFLY VALVES INSTALLATION INSTRUCTIONS
ELECTRIC ACTUATOR AND CONTROLLER FOR AKRON BUTTERFLY VALVES INSTALLATION INSTRUCTIONS The electric actuator and controller is designed to operate current model Akron Style 7940, 7945, 7950 and 7960 Butterfly
More information3061, 3096, 3126 foam systems gpm Installation Instructions
3061, 3096, 3126 foam systems 60-95-125 gpm Installation Instructions Bypass eductor Eductor is available with the following inlet and outlet connections: 2 NPT, 2 Victaulic and 2 1/2 NPT. Eductor may
More informationSTYLE 3440 DECKMASTER ELECTRIC MONITOR INSTALLATION, OPERATING, AND MAINTENANCE INSTRUCTIONS
STYLE 3440 DECKMASTER ELECTRIC MONITOR INSTALLATION, OPERATING, AND MAINTENANCE INSTRUCTIONS The following is intended to provide the basic instructions for installation, operation and maintenance of the
More informationSTYLE 624, 638 QUICK-ATTACK FOAM TUBE INSTALLATION, OPERATING, AND MAINTENANCE INSTRUCTIONS
STYLE 624, 638 QUICK-ATTACK FOAM TUBE INSTALLATION, OPERATING, AND MAINTENANCE INSTRUCTIONS The following is intended to provide the basic instructions for installation, operation, and maintenance. Read
More informationSTYLE 9300 FLOW/PRESSURE METER INSTALLATION & OPERATING INSTRUCTIONS
STYLE 9300 FLOW/PRESSURE METER INSTALLATION & OPERATING INSTRUCTIONS INTRODUCTION The Style 9300 Flow/Pressure Meter from Akron is designed to offer reliable and accurate service with an easy to install,
More informationMaximum Flow: 600 GPM (3800 LPM) Portable Base 1250 GPM (4800 LPM) Direct Mount. Maximum Pressure: 200 PSI (1380 Kpa, 13.8 BARS)
STYLE 3414 Apollo S.I. Monitor with FoldING Legs OPERATING & MAINTENANCE INSTRUCTIONS WITH SPECIAL L.A. COUNTY SPECIFICATIONS The Akron Style 3414 Apollo Monitor is designed to provide efficient trouble-free
More informationSTYLE 3440 DECKMASTER ELECTRIC MONITOR WITH POSITION FEEDBACK INSTALLATION, OPERATING, AND MAINTENANCE INSTRUCTIONS
STYLE 3440 DECKMASTER ELECTRIC MONITOR WITH POSITION FEEDBACK INSTALLATION, OPERATING, AND MAINTENANCE INSTRUCTIONS The following is intended to provide the basic instructions for installation, operation
More information3061, 3096, 3126 FOAM SYSTEMS GPM INSTALLATION INSTRUCTIONS
3061, 3096, 3126 SYSTMS 60-95-125 GPM INSTALLATION INSTRUCTIONS BYPASS DUCTOR ductor is available with the following inlet and outlet connections: Connections available in 2" NPT, 2" Victaulic and 2 1/2"
More informationProduct Ratings Electrical Specifications
STYLE 3440 DECKMASTER ELECTRIC MONITOR FOR STANDARD CONFIGURATION WITH POTENTIOMETERS & U2 LOGIC BOX INSTALLATION, OPERATING, AND MAINTENANCE INSTRUCTIONS The following is intended to provide the basic
More information3061, 3096, 3126 foam systems gpm Installation Instructions
3061, 3096, 3126 foam systems 60-95-125 gpm Installation Instructions Bypass eductor ductor is available with the following inlet and outlet connections: 2 NPT, 2 Victaulic and 2 1/2 NPT. ductor may be
More informationDAP-625S and DAP-875S
AIR CHAMP PRODUCTS DAP-625S and DAP-875S (i) FORM NO. L-20078-B-0501 In accordance with Nexen s established policy of constant product improvement, the specifications contained in this manual are subject
More informationElgin Hydraulic Clutch-Brake ECB-240, Product Number FORM NO. L F FORM NO. L F-0704
Elgin Hydraulic Clutch-Brake ECB-20, Product Number 96225 FORM NO. L-20283-F-070 1 FORM NO. L-20283-F-070 In accordance with Nexen s established policy of constant product improvement, the specifications
More informationUSER MANUAL. NEMA 48C Flange Mounted, Enclosed, Clutch Brake. FMCBE Model 500 FORM NO. L A (i)
USER MANUAL NEMA 48C Flange Mounted, Enclosed, Clutch Brake FMCBE Model 500 (i) In accordance with Nexen s established policy of constant product improvement, the specifications contained in this manual
More informationModel GP Triplex Ceramic Plunger Pump Operating Instructions/ Manual
Model GP6145-3100 Triplex Ceramic Plunger Pump Operating Instructions/ Manual Contents: Installation Instructions: page 2 Pump Specifications: page 3 Exploded View: page 4 Parts List / Kits: page 5 Repair
More informationModel GXR Series. Consumer Pump. Triplex Plunger Pump Operating Instructions/ Repair Instructions Manual
Model GXR Series Triplex Plunger Pump Operating Instructions/ Repair Instructions Manual Consumer Pump Horizontal/Vertical Pump with built-in Regulator, Thermal Relief Valve and Siphon Injector Updated
More informationDome-Loaded Pressure Reducing BD-Series
Dome-Loaded Pressure Reducing BD-Series *Parts will differ for high pressure valves. Load Piston - Piston - U-cup U-cup Piston 1. Carefully place the u-cup over the neck of the piston. Load Cylinder -
More informationModel BP6150. Triplex Ceramic Plunger Pump Operating Instructions/ Manual
Model BP6150 Triplex Ceramic Plunger Pump Operating Instructions/ Manual Contents: Installation Instructions: page 2 Pump Specs: page 3 Exploded View: page 4 Parts List / Kits Torque Specifications: page
More informationModel GXR Series. Consumer Pump. Triplex Plunger Pump Operating Instructions/ Repair Instructions Manual
Model GXR Series Triplex Plunger Pump Operating Instructions/ Repair Instructions Manual Consumer Pump Horizontal/Vertical Pump with built-in Regulator, Thermal Relief Valve and Siphon Injector Updated
More informationINSTRUCTIONS AND SERVICE MANUAL WITH PARTS LIST
CMP SERIES CPM15-15B (25905F300) CPM15-15B-H/D (25905F301) CPM18-15B (25905F303) CPM18-15B-H/D (25905F304) INDUSTRIAL PUMPS INSTRUCTIONS AND SERVICE MANUAL WITH PARTS LIST NOTE! To the installer: Please
More informationBC Brake Caliper. (i) MEX (55) QRO (442) MTY (81) DIST. AUTORIZADO
MEX (55) 5 6 QRO (44) 95 7 60 MTY () 54 0 BC Brake Caliper (i) FORM NO. L-0066-B-040 In accordance with Nexen s established policy of constant product improvement, the specifications contained in this
More informationModel CP420/CP425. Triplex Ceramic Plunger Pump Operating Instructions/ Repair and Service Manual
Model CP420/CP425 Triplex Ceramic Plunger Pump Operating Instructions/ Repair and Service Manual Updated 02/12 Contents: Installation Instructions: page 2 Pump Specifications: page 3 Exploded View: page
More information4000SS. For other repair kits and service parts, send for Ames Repair Parts Price List, PL-A-RP-BPD.
Series 4000SS RP/IS-A-4000SS 4000SS Reduced Pressure Zone Assemblies Sizes: 8" 10" (200 250mm) Installation Service Repair Kits Maintenance For other repair kits and service parts, send for Ames Repair
More informationrings used in the TuckAway Electric Monitor (#3352)
STYLE 3352 O-Ring Ring Replacement Guide The following tools & materials are required for disassembly & servicing of the O-rings rings used in the (#3352) 5/64 Allen wrench 7/64 Allen wrench* 3/16 Allen
More informationModel GXR Series. Consumer Pump. Triplex Plunger Pump Operating Instructions/ Repair Instructions Manual
Model GXR Series Triplex Plunger Pump Operating Instructions/ Repair Instructions Manual Consumer Pump Horizontal/Vertical Pump with built-in Regulator, Thermal Relief Valve and Siphon Injector MADE IN
More informationSeries CP200. Triplex Ceramic Plunger Pump Operating Instructions/ Repair and Service Manual. For Models: CP218 CP219 CP220 CP230
Series CP200 Triplex Ceramic Plunger Pump Operating Instructions/ Repair and Service Manual For Models: CP218 CP219 CP220 CP230 Updated 10/02 Contents: Installation Instructions: page 2 Pump Specifications:
More informationInstallation, Operation and Maintenance Manual
IOM-HS-QTColdBevMax Installation, Operation and Maintenance Manual QT TM Cold Bev Max TM Models: QTCLDBMX-1S-.5M, QTCLDBMX-2S-.5M, QTCLDBMX-3S-.5M, QTCLDBMX-4S-.5M, QTCLDBMX-5S-.5M Tested and Certified
More informationSpring-Engaged/Hydraulically-Released BD Caliper Brake. (i) MTY (81) QRO (442) MEX (55)
Spring-Engaged/Hydraulically-Released BD Caliper Brake (i) FORM NO. L-07-E-0300 In accordance with Nexen s established policy of constant product improvement, the specifications contained in this manual
More informationMetroPrime 22MPC Self-Priming Centrifugal Pump
Page 1 of 6 prevent priming or reduce pump capacity. OPERATION The 22 MPC-Metropolitan Pump is a self-priming centrifugal pump and only requires priming prior to its initial start. The pump will retain
More informationService Guide JATCO Environmental Protection Tank Model J-7000
Service Guide JATCO Environmental Protection Tank Model J-7000 Listed below are a series of steps to follow if the JATCO tank fails to dump properly. #1. Be sure there is an adequate supply of gas pressure
More informationData Sheet 11.1 Issue A
TECHNICAL DATA : MODEL A & B Data Sheet 11.1 Page 1 of 6 MAXIMUM WORKING PRESSURE MINIMUM EFFECTIVE WORKING PRESSURE END CONNECTION MATERIAL 12.3 Kg./Sq.Cm. (175 psi) 7 Kg./Sq.Cm. (100 psi) maximum 1.4
More informationARSD3FA-M325 Pneumatic Nutrunner Parts List
ARSDFA-M Pneumatic Nutrunner Parts List Feb. 0 Model No. ARSDFA-M Table of Contents Tool Breakdown Assembly....... Stall Motor Group........ AS Valve Sub-Assembly....... Valve Stem Sub-Assembly.......
More informationModels P420A-3100 & P420A-5100
Models P420A-3100 & P420A-5100 Triplex Ceramic Plunger Pump Operating Instructions/ Repair and Service Manual Corrossion Resistant Pumps Contents: Installation Instructions: page 2 Specifications: page
More informationP SERIES PUMPS. 18mm Versions Nickle-Aluminum Bronze Models: P , P , P , P , P , P , P
P200-3100 SERIES PUMPS 18mm Versions Nickle-Aluminum Bronze Models: P217-3100, P218-3100, P219-3100, P220-3100, P221-3100, P227-3100, P230-3100 Triplex Ceramic Plunger Pump Operating Instructions/ Repair
More informationInverted High Pressure Fluid Filters
Instruction Sheet P/N 33290-03 Description See Figure. Nordson high-pressure fluid filters prevent nozzle-plugging by filtering contaminants out of coating materials. These stainless steel, wall-mounted
More informationHighly Styled, Low Cost Serpentine Drive
Revised 12-9-08 Highly Styled, Low Cost Serpentine Drive Installation Instructions Chevy Small Block Kit #21100 (without Power Steering) and #21150 (with Remote Power Steering) and #21155 (with Saginaw
More informationHighly Styled, Low Cost Serpentine Drive
Revised 11-15-11 Highly Styled, Low Cost Serpentine Drive Installation Instructions Chevy Small Block Kit #21110 (without Power Steering) Kit #21160 (with Remote Power Steering) Kit #21165 (with Saginaw
More informationEffective June 2016 New Issue
Voltage Regulators MN225035EN Effective June 2016 New Issue COOPER POWER SERIES QD8 Quik-Drive Tap-Changer Switch Assembly Kit 5740785B13 and Switch Neutral Stationary Assembly Kit 5791646A48 Installation
More information3.2 DRIVE TORQUE HUB. Roll, Leak and Brake Testing SECTION 3 - CHASSIS & TURNTABLE. 3-2 JLG Lift
3.2 DRIVE TORQUE HUB Roll, Leak and Brake Testing 10 LUG PATTERN Torque-Hub units should always be roll and leak tested before disassembly and after assembly to make sure that the unit's gears, bearings
More informationOperating Instructions and Parts Manual AHR-50 Auto Rewind Hose Reel
Operating Instructions and Parts Manual AHR-50 Auto Rewind Hose Reel JET 427 New Sanford Road LaVergne, Tennessee 37086 Part No. M-426238 Ph.: 800-274-6848 Revision C 04/2017 www.jettools.com Copyright
More informationPPM EO-100 TM. Operation Manual
PPM EO-100 TM Open Loop Electric Prewet Power Module Operation Manual Rev A Page 1 2/23/2010 Copyright 2008 by Cirus Controls, LLC. All Rights Reserved. No part of this material may be reproduced in any
More informationModel GX Series. Consumer Pump. Triplex Plunger Pump Operating Instructions/ Repair Instructions Manual
Model GX Series Triplex Plunger Pump Operating Instructions/ Repair Instructions Manual Consumer Pump Horizontal/Vertical Pump with built-in Thermal Relief Valve and Siphon Injector Contents: Installation
More informationDIAMOND CONCRETE SAW PARTS LIST MODEL CC8000 P R O D U C T S. (Revised )
DIAMOND P R O D U C T S CONCRETE SAW PARTS LIST MODEL CC8000 (Revised 10-15-2002) Table of Contents Page Saw Controls Legend. 3 Drawing 1. Frame Group. 4-5 Drawing 2. Arm Assembly... 6-7 Drawing 3. Hydraulics
More informationModel. Triplex Ceramic Plunger Pump Operating Instructions/ Repair and Service Manual SP100W/SP351W
Model Triplex Ceramic Plunger Pump Operating Instructions/ Repair and Service Manual SP100W/SP351W Contents: Installation Instructions: page 2 Pump Specifications: pages 3-4 Parts List/Torque Specs.: page
More informationtechnical service parts
style 5 Trident Dual gallonage technical service parts 0 5 4 5 4 5 4 5 4 5 4 5 4 5 9 9 0 9 4 5 8 8 9 9 9 9 9 0 4 8 9 9 04 0 0 5 0 8 4 5 9 USE PERMABOND LM OR LOCTITE TORQUE TO IN-LBS BOND SPACERS TOGETHER
More informationV400D VERIS Verabar (Double Rod) Installation and Maintenance Manual
V400D VERIS Verabar (Double Rod) Installation and Maintenance Manual 168-EN Please read and save these instructions Contents General Safety Information...3 Product Information...3 Section 1: Scope...3
More informationAir Operated Diaphragm Pumps Operating and Maintenance Instructions
Product & Chemical Disclaimer The user must take responsibility in the selection of the products materials of construction. Empire Pumps Ltd will act in an advisory role and offer recommendations; however,
More informationWatts Series CSM-91. Grooved/Flanged Flow Measurement/Balancing Valves. Installation and Operating Instructions. Table of Contents. 1.
Watts Series CSM-9 Grooved/Flanged Flow Measurement/Balancing Valves Installation and Operating Instructions IS-CSM-9 Table of Contents Item Description Page. Installation of Valve Angle Design 2. Installation
More informationModel GP7122. Triplex Ceramic Plunger Pump Operating Instructions/ Repair and Service Manual
Model GP7122 Triplex Ceramic Plunger Pump Operating Instructions/ Repair and Service Manual Contents: Installation Instructions: page 2 Pump Specifications: page 3 Exploded View: page 4 Parts List: page
More informationColt Series C400, C500
Colt Series C400, C500 RP/IS-A-C400/C500 C400 OSY Reduced Pressure Zone Assemblies Reduced Pressure Detector Assemblies Sizes: 2 1 2" 10" (65 250mm) Installation Service Repair Kits Maintenance For other
More informationThrough-Shaft Clutch-Brake LSCB-32HT, LSCB-32HT, LSCB-44, LSCB-44HT, LSCB-54HT FORM NO. L D-0606 MEX (55) QRO (442)
Through-Shaft Clutch-Brake LSCB-HT, LSCB-HT, LSCB-, LSCB-HT, LSCB-5HT In accordance with Nexen s established policy of constant product improvement, the specifications contained in this manual are subject
More informationINSTALLATION INSTRUCTIONS, PARTS LIST AND CONFIGURATION GUIDE FOR THE CARBONATOR. Large Model No
Please refer to the Schroeder America website (www.schroederamerica.com) for information relating to Schroeder America installation and Service Manuals, Instruction Sheets, Technical Bulletins, Service
More informationG8 Portable Fuel Transfer Pump Owner s Manual
G8 Portable Fuel Transfer Pump Owner s Manual GENERAL INFORMATION This pump is designed for use only with gasoline (up to 15% alcohol blends such as E15), diesel fuel (up to 20% biodiesel blends such as
More informationProposition 65 Warning This product contains chemicals known to the State of California to cause cancer or birth defects or other reproductive harm.
Model RPHBM Hydrant Backflow Meter Installation Testing Maintenance Instructions CAUTION: Installation of Backflow Preventers must be performed by qualified, licensed personnel. The installer should be
More informationDEMA MODEL 692T FOAM STATION I INSTALLATION INSTRUCTION
1. PARTS CHECKLIST: ITEM DESCRIPTION QTY. A. Foam Station Assembly 1 B. #10 Screw & Anchor Kit Set (Total: 4 Screws & 4 Anchors) 1 C. Ceramic Weight 1 D. ¼ ID Tubing & Foot Valve Assembly 1 E. Metering
More informationStraight-Bore Clutch LSCC-32, 44, 54
Straight-Bore Clutch LSCC-32, 44, 54 1 In accordance with Nexen s established policy of constant product improvement, the specifications contained in this manual are subject to change without notice. Technical
More informationGH-BETTIS SERVICE INSTRUCTIONS DISASSEMBLY & REASSEMBLY FOR MODELS HD521-M4, HD721-M4 AND HD731-M4 DOUBLE ACTING SERIES PNEUMATIC ACTUATORS
GH-BETTIS SERVICE INSTRUCTIONS DISASSEMBLY & REASSEMBLY FOR MODELS HD521-M4, HD721-M4 AND HD731-M4 DOUBLE ACTING SERIES PNEUMATIC ACTUATORS WITH HYDRAULIC CONTROL PACKAGE PART NUMBER: SE-023 REVISION:
More informationParts 3A2528C EN. Mark VII Max, Mark X Premium, and Mark X Max Electric Airless Sprayers
Parts Mark VII Max, Mark X Premium, and Mark X Max Electric Airless Sprayers 3A2528C EN For Portable Airless Spraying of Architectural Coatings and Paints. For professional use only. Not approved for use
More informationLiquid Turbine Flowmeter
NUFLO Liquid Turbine Flowmeter User Manual 167018 Explosion-proof for use in Class I, Division I, Groups A, B, C, D Hazardous Environments ANSI 12.27.01-2003 Single Seal Part No. 9A-100062201, Rev. 01
More informationOWNER S MANUAL. 6. If you aren t competent to instal the pump, get help from a qualified source.
OWNER S MANUAL RK2 Systems Pro Pump Energy-Efficient, Self Priming Centrifugal Pumps Important Safety Instructions Please read all instructions completely before you install or operate your new pump. Save
More informationAir Operated Double Diaphragm Pump. M-Pump ½ Metallic Non Metallic Pump INSTALLATION, OPERATION & MAINTENANCE MANUAL
Air Operated Double Diaphragm Pump M-Pump ½ Metallic Non Metallic Pump INSTALLATION, OPERATION & MAINTENANCE MANUAL 0.5 I.O.M rev 05. 12/2015 INDEX Title Section Introduction.1 Safety.2 Warranty, General
More informationLaboratory Series. Ultraviolet Ozone Destruct System Installation, Operation and Maintenance Manual. One Source for All Your UV Needs!
Laboratory Series Ultraviolet Ozone Destruct System Installation, Operation and Maintenance Manual KEEP THIS MANUAL ON HAND IT IS IMPORTANT THAT THOSE RESPONSIBLE FOR THE INSTALLATION OF THIS EQUIPMENT,
More informationAVK SERIES 41 SWING CHECK VALVE FIELD MAINTENANCE AND INSTRUCTION MANUAL FOR SWING CHECK VALVES 3" - 12"
AMERICAN AVK COMPANY AVK SERIES 41 SWING CHECK VALVE FIELD MAINTENANCE AND INSTRUCTION MANUAL FOR SWING CHECK VALVES 3" - 12" TABLE OF CONTENTS EXPLODED ASSEMBLY / PARTS LIST INTRODUCTION / DESCRIPTION
More informationIntended Use: Explanation of Signal Word Consequences
SAFETY INFORMATION & INSTRUCTION MANUAL Please read, understand, and follow all safety information contained in these instructions prior to the use of this device. Retain these instructions for future
More informationInstallation, Operation and Maintenance Manual
IOM-HS-QTCubeMax Installation, Operation and Maintenance Manual QT TM Cube Max TM Models: QTCBMX-1S-1M, QTCBMX-2S-1M, QTCBMX-3S-1M, QTCBMX-4S-1M, QTCBMX-1L-1M, QTCBMX-2L-1M, QTCBMX-3L-1M, QTCBMX-4L-1M,
More informationINSTALLATION & MAINTENANCE MODEL mm
MODEL 65-25mm INSTALLATION INSTRUCTIONS CAUTION: Installation of Backflow Preventers must be performed by qualified, licensed personnel. The installer should be sure the proper device has been selected
More informationArtesian2 Owners Manual
Artesian2 Owners Manual Energy-Efficient, Self Priming Centrifugal Pumps Discharge Inlet Important Safety Instructions Please read all instructions completely before you install or operate your new pump.
More informationAir Trap TATSU2. Copyright 2013 by TLV CO., LTD. All rights reserved ISO 9001/ ISO M-02 (TATSU2) 7 August 2013.
172-65177M-02 (TATSU2) 7 August 2013 ISO 9001/ ISO 14001 Manufacturer Kakogawa, Japan is approved by LRQA LTD. to ISO 9001/14001 Air Trap TATSU2 Copyright 2013 by TLV CO., LTD. All rights reserved 1 Contents
More informationParts list. See Frame parts list Page 12. See hydraulic pump. exploded view. Page 14. See work head. exploded view. Page 7
Parts list See Frame parts list Page 12 See hydraulic pump exploded view Page 14 See work head exploded view Page 7 See electrical parts list Page 18 See hoist parts list Page 11 See Frame parts list Page
More informationEZ-IN Series Turbine Flowmeter
Class I, Group A, B, C, D, Division I Complies with ASME Standard B31.3 NUFLO EZ-IN Series Turbine Flowmeter Installation Manual Part No. 9A-100062997, Rev. 01 Measurement Systems EZ-IN Series BF Turbine
More informationAVK SERIES 41 SWING CHECK VALVE FIELD MAINTENANCE AND INSTRUCTION MANUAL FOR SWING CHECK VALVES 3" - 12"
AMERICAN AVK COMPANY AVK SERIES 41 SWING CHECK VALVE FIELD MAINTENANCE AND INSTRUCTION MANUAL FOR SWING CHECK VALVES 3" - 12" TABLE OF CONTENTS EXPLODED ASSEMBLY / PARTS LIST INTRODUCTION / DESCRIPTION
More informationMODEL 5120 Tire Repair Station
MODEL 5120 Tire Repair Station 00-0049 Installation, Operation & Repair Parts Information Branick Industries, Inc. 4245 Main Avenue P.O. Box 1937 Fargo, North Dakota 58103 REV01182017 P/N: 81-0058G CAUTION
More informationCirculation Kits for CP Pumps
Instruction Sheet P/N 08000C Description This instruction sheet covers two circulation kits for CP Pumps: Stainless steel circulation kit, with Viton O-rings Stainless steel circulation kit, with EPR O-rings
More informationInstallation Instructions
Installation Instructions AMP RESEARCH Power Step by Bestop Automatic Retracting Running Board Vehicle Application Nissan Titan King Cab 2004 and newer (5 ft.) Part Number: 75106-01 Nissan Titan Crew Cab
More informationHALLMARK INDUSTRIES INC
Performance Part No. HP. CONVERTIBLE JET PUMP USER S MANUAL GPH of Water @ Total Discharge Pressure of 40 psi Max. Pressure Max suction (shallow well) Max Suction (deep well) Max GPM (@0 head) Max Discharge
More informationDEMA MODEL 693T FOAM STATION II INSTALLATION INSTRUCTION
1. PARTS CHECKLIST: 2. INSTALLATION: DEMA MODEL 93T FOAM STATION II ITEM DESCRIPTION QTY. A. Foam Station Assembly 1 B. ¼ ID Tubing & Foot Strainer 1 C. 3/ ID Tubing & Foot Strainer 1 D. Ceramic Weight
More informationEasytork Solenoid Valve IOM
Easytork Solenoid Valve IOM General This installation document is to be read in conjunction with the Easytork Vane Actuator IOM. Description The Easytork Solenoid Valve ( ESV ) series is intended for the
More informationTECHNICAL SERVICE MANUAL
Electronic copies of the most current TSM issue can be found on the Viking Pump website at www.vikingpump.com TECHNICAL SERVICE MANUAL Viking In-Line Helical Gear Reducers Sizes 11, 21, 31, 35, 41, 51,
More informationLDS-455 PREWETTING SYSTEM
LDS-455 PREWETTING SYSTEM 4GPM & 7GPM Service and Parts Manual Monroe Snow & Ice Control A Division of Monroe Truck Equipment 1051 W. 7th Street Monroe, WI 53566 Phone: 608-328-8127 05051882-6 03/11/2016
More informationModel 5-025, 5-050, &
Model 5-025, 5-050, 5-075 & 5-150 7 Model 5-025, 5-050, 5-075 & 5-150 8 Eductor Block Exploded View Model 5-025, 5-050, 5-075 & 5-150 9 Figure 1 Item Part Name Model Model Model Model 5-025 5-050 5-075
More informationArctic Equipment Manufacturing Corporation R04 M673F Power Unit Kit Installation Instructions. M673F installation instructions
Arctic Equipment Manufacturing Corporation R04 M673F Power Unit Kit Installation Instructions M673F installation instructions Arctic Equipment Manufacturing Corporation R04 M673F Power Unit Kit Installation
More informationModel CP470. Triplex Ceramic Plunger Pump Operating Instructions/ Repair and Service Manual
Model Triplex Ceramic Plunger Pump Operating Instructions/ Repair and Service Manual CP470 Updated 06/17 Contents: Installation Instructions: page 2 Pump Specifications: page 3 Exploded View: page 4 Part
More informationMODEL HD-BTC. Installation, Operation & Repair Parts Information REV041416
MODEL HD-BTC Installation, Operation & Repair Parts Information REV041416 TABLE OF CONTENTS SAFETY INSTRUCTIONS 1 DEFINITIONS 1 SPECIFICATIONS 2 INSTALLATION INSTRUCTIONS 2 OPERATING INSTRUCTIONS 2 MAINTENANCE
More informationV200D VERIS Verabar (Double Rod) Installation and Maintenance Manual
V200D VERIS Verabar (Double Rod) Installation and Maintenance Manual 173-EN Please read and save these instructions Contents General Safety Information...3 Product Information...3 Section 1: Scope...3
More informationA Member of the. Integrated Metering Technologies
I n s t a l l a t i o n M a n u a l A Member of the Integrated Metering Technologies 1.0 General and Safety Do not install, operate or maintain this flow meter without reading, understanding and followingthe
More informationCOOPER POWER SERIES. QD5 Quik-Drive tap-changer reversing neutral stationary contact asssembly kit A26 installation instructions
Voltage Regulators MN225025EN Effective March 2016 Supersedes S225-50-48 November 2008 COOPER POWER SERIES QD5 Quik-Drive tap-changer reversing neutral stationary contact asssembly kit 5791646A26 installation
More information70 Series 8700 Coupler 2-pc Hub & Shaft Three Phase Brake Instructions IP43 & IP56 (NEMA 2 & 4) Housing
Bulletin No. BK4775-3 (08/2016) 70 Series 8700 Coupler 2-pc Hub & Shaft Three Phase Brake Instructions IP43 & IP56 (NEMA 2 & 4) Housing Read carefully before attempting to assemble, install, operate or
More informationBMK-30. Heavy-Duty By-Pass Filtration System Installation and Servicing Instructions
BMK-30 Heavy-Duty By-Pass Filtration System Installation and Servicing Instructions IMPORTANT NOTICE Read all instructions completely before attempting to install this unit. Improper installation could
More informationDO NOT INSULATE BELOW THIS LINE. * For sizes 1/2" to 1 1/2" add 2 1/2" to 'C' dimension.
428 Jones Boulevard Limerick Airport Business Center Pottstown, PA 19464 Phone: (610)495-5131 ax: (610)495-5134 www.watsonmcdaniel.com PAGE 28 INSTRUCTION PART NO. 2315400 C.R.3500 REV. 10 SIZE C B CENTER
More information24V Solar Charger. Instructions READ CAREFULLY Garrymore Ln Missoula, MT
24V Solar Charger 9889 Garrymore Ln Missoula, MT 59808 888-687-3552 +1-406-549-0769 www.aquacreek.com Instructions PART #: F-044SCH (For use with Pro Pool, Ranger, Ambassador & Pathfinder) MANDATORY LEAVE
More informationFCB-450, LCB-600, MCB-800
AIR CHAMP PRODUCTS User Manual FCB-450, LCB-600, MCB-800 Clutch-Brakes (i) In accordance with Nexen s established policy of constant product improvement, the specifications contained in this manual are
More informationBD SUPER B SPECIAL Dodge 5.9L Cummins 24v ISB
1 This turbo is intended for high performance applications and is not to be used for towing applications BD SUPER B SPECIAL 1994-2002 Dodge 5.9L Cummins 24v ISB Part# 1045120 PLEASE READ ALL INSTRUCTIONS
More information