Additions, Revisions, or Updates
|
|
- Walter Rose
- 5 years ago
- Views:
Transcription
1 SUBJECT DATE Flushing the Engine Lubrication System March 2018 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change EPA07/ DDC-SVC-MAN-0081 EPA10/ GHG14 DD HD Flushing the Engine Lubrication System This is a new section. DDC-SVC-MAN-0190 GHG17 HD DD All information subject to change without notice Copyright 2018 DETROIT DIESEL CORPORATION
2 2 Flushing the Engine Lubrication System 2 Flushing the Engine Lubrication System This procedure is used to flush the engine lubrication system and oil coolant module after an engine component failure occurs that contaminates the system with metallic debris. Flushing the lubrication system is only necessary if there is metallic debris in the oil sump and metallic debris in the pleats of the oil filter element. Failures that create extensive debris may include connecting rod or main bearing failure, gear train failure, or turbocompound system failure (if equipped). This flushing procedure should be performed before any of the failed parts are removed, so pressure is maintained in the engine lubrication circuit. Only use this procedure when the engine will be repaired, and not replaced. Table 1. Special Service Tools Used in the Procedure Tool Numbers Tool Name Tool Graphic J Oil Priming Adaptor J or Equivalent Oil Pre-Lube Kit Flush the cylinder block and engine lubrication system as follows: 1. Is the cylinder block (including main bearing caps) damaged from a spun main bearing shell? a. Yes; replace the engine. b. No; Go to step Shut off the engine, apply the parking brake, chock the wheels, and perform any other applicable safety steps. CAUTION: ELECTRICAL SHOCK To avoid injury from electrical shock, use care when connecting battery cables. The magnetic switch studs are at battery voltage. 3. Disconnect the batteries. 4. Open the hood. 5. If necessary, remove the bumper for access. Refer to the Original Equipment Manufacturer (OEM) procedure. 6. Remove the oil coolant module from the engine. Refer to section "Removal of the Oil Coolant Module". NOTICE: Use a clean work bench during oil coolant module disassembly and reassembly. Organize the parts so they can be reassembled after flushing the module. 4 All information subject to change without notice. Copyright 2018 DETROIT DIESEL CORPORATION
3 Remove the oil filter and oil filter cap from the oil coolant module. Discard filter and cap O-ring. Save the cap for cleaning. 8. Remove the oil filter standpipe. Save for cleaning. 9. Remove the oil thermostat and thermostat cover (if equipped). Discard seal. Save the thermostat and cover for cleaning. 10. Remove the oil cooler and oil cooler O-rings. Discard the cooler and O-rings. 11. Remove the oil filler cap. Save for cleaning. 12. Remove any oil passage plugs. Discard O-rings or sealing rings. Save plugs for cleaning. 13. Remove the coolant drain plug (below coolant thermostat cavity). Discard O-ring. Save plug for cleaning. Figure 1. Oil Coolant Module with Lubrication Components Removed All information subject to change without notice Copyright 2018 DETROIT DIESEL CORPORATION
4 2 Flushing the Engine Lubrication System Figure 2. Lubrication System Components Removed from Oil Coolant Module 14. Use a parts washer or steam cleaner to flush all of the oil passages in the oil coolant module. 15. Use appropriate brushes to remove stubborn debris. Ensure any residual oil, dirt, metal, or other contaminates have been removed from all of the oil cavities and passages in the oil coolant module. See illustrations below for examples of an oil coolant module that has been cleaned. 6 All information subject to change without notice. Copyright 2018 DETROIT DIESEL CORPORATION
5 Figure 3. Clean Oil Filter Housing Figure 4. Clean Oil Cavity All information subject to change without notice Copyright 2018 DETROIT DIESEL CORPORATION 7
6 2 Flushing the Engine Lubrication System Figure 5. Clean Oil Passage WARNING: EYE INJURY To avoid injury from flying debris when using compressed air, wear adequate eye protection (face shield or safety goggles) and do not exceed 276 kpa (40 psi) air pressure. 16. Blow out and dry the oil passages in the oil coolant module with compressed air. 17. Clean the components removed during disassembly that will be reused. 18. Reassemble the oil coolant module using a new oil cooler, oil filter, gaskets and seals. Refer to the appropriate sections in the Workshop Manual for installation instructions. 19. Install the oil coolant module onto the engine. Refer to section "Installation of the Oil Coolant Module". NOTE: The oil pan must be thoroughly cleaned when debris has contaminated the engine lubrication system. The engine could be contaminated again if debris is allowed to remain in the sump and circulate. 20. Remove the oil pan, if not already removed. Refer to section "Removal of the Oil Pan". 21. Place a drain pan under the engine to catch oil from the flushing procedure. 22. Using a 17 mm Allen tool, remove the Allen head plug from the oil priming port (1) on the oil coolant module. 8 All information subject to change without notice. Copyright 2018 DETROIT DIESEL CORPORATION
7 If equipped with an oil sample valve at the oil priming port, remove the valve and sealing washer NOTE: Tool J is used to adapt the J oil pre-lube kit for use on a DD platform heavy duty engine. 24. Install the oil priming adaptor (J-49181) into the oil priming port in the oil coolant module. Hand-tighten the adaptor. NOTICE: If chassis application prevents access, a 45-degree or 90-degree pipe fitting (1/4" NPT) can be used as an adaptor. 25. Attach the engine pre-lube kit (J-45299) to the oil priming adaptor. 26. Fill the canister with eight quarts of clean engine oil, meeting the operating requirements of the engine. 27. Open the valve on the primer and start pumping until the container is almost empty. 28. The engine lubrication system has now been flushed. 29. Close the valve on the primer and loosen the fitting; do not completely remove it from the adaptor. 30. Remove the priming adaptor from the oil coolant module with the primer line attached to keep the oil from flowing out of the module. 31. Install the Allen head plug or oil sample valve into the oil coolant module and torque to 70 to 80 N m (51 to 59 lb ft). 32. Continue with the necessary repairs to the engine. Refer to the appropriate section(s) in the applicable Workshop Manual. All information subject to change without notice Copyright 2018 DETROIT DIESEL CORPORATION
8 3 Flushing the Engine Lubrication System 3 Flushing the Engine Lubrication System This procedure is used to flush the engine lubrication system and oil coolant module after an engine component failure occurs that contaminates the system with metallic debris. Flushing the lubrication system is only necessary if there is metallic debris in the oil sump and metallic debris in the pleats of the oil filter element. Failures that create extensive debris may include connecting rod or main bearing failure, gear train failure, or turbocompound system failure (if equipped). This flushing procedure should be performed before any of the failed parts are removed, so pressure is maintained in the engine lubrication circuit. Only use this procedure when the engine will be repaired, and not replaced. Table 2. Special Service Tools Used in the Procedure Tool Numbers Tool Name Tool Graphic J Oil Priming Adaptor J or Equivalent Oil Pre-Lube Kit Flush the cylinder block and engine lubrication system as follows: 1. Is the cylinder block (including main bearing caps) damaged from a spun main bearing shell? a. Yes; replace the engine. b. No; Go to step Shut off the engine, apply the parking brake, chock the wheels, and perform any other applicable safety steps. CAUTION: ELECTRICAL SHOCK To avoid injury from electrical shock, use care when connecting battery cables. The magnetic switch studs are at battery voltage. 3. Disconnect the batteries. 4. Open the hood. 5. If necessary, remove the bumper for access. Refer to the Original Equipment Manufacturer (OEM) procedure. 6. Remove the oil coolant module from the engine. Refer to section "Removal of the Oil Coolant Module". NOTICE: Use a clean work bench during oil coolant module disassembly and reassembly. Organize the parts so they can be reassembled after flushing the module. 10 All information subject to change without notice. Copyright 2018 DETROIT DIESEL CORPORATION
9 Remove the oil filter and oil filter cap from the oil coolant module. Discard filter and cap O-ring. Save the cap for cleaning. 8. Remove the oil filter standpipe. Save for cleaning. 9. Remove the oil thermostat and thermostat cover (if equipped). Discard seal. Save the thermostat and cover for cleaning. 10. Remove the oil cooler and oil cooler O-rings. Discard the cooler and O-rings. 11. Remove the oil filler cap. Save for cleaning. 12. Remove any oil passage plugs. Discard O-rings or sealing rings. Save plugs for cleaning. 13. Remove the coolant drain plug (below coolant thermostat cavity). Discard O-ring. Save plug for cleaning. Figure 6. Oil Coolant Module with Lubrication Components Removed All information subject to change without notice Copyright 2018 DETROIT DIESEL CORPORATION
10 3 Flushing the Engine Lubrication System Figure 7. Lubrication System Components Removed from Oil Coolant Module 14. Use a parts washer or steam cleaner to flush all of the oil passages in the oil coolant module. 15. Use appropriate brushes to remove stubborn debris. Ensure any residual oil, dirt, metal, or other contaminates have been removed from all of the oil cavities and passages in the oil coolant module. See illustrations below for examples of an oil coolant module that has been cleaned. 12 All information subject to change without notice. Copyright 2018 DETROIT DIESEL CORPORATION
11 Figure 8. Clean Oil Filter Housing Figure 9. Clean Oil Cavity All information subject to change without notice Copyright 2018 DETROIT DIESEL CORPORATION 13
12 3 Flushing the Engine Lubrication System Figure 10. Clean Oil Passage WARNING: EYE INJURY To avoid injury from flying debris when using compressed air, wear adequate eye protection (face shield or safety goggles) and do not exceed 276 kpa (40 psi) air pressure. 16. Blow out and dry the oil passages in the oil coolant module with compressed air. 17. Clean the components removed during disassembly that will be reused. 18. Reassemble the oil coolant module using a new oil cooler, oil filter, gaskets and seals. Refer to the appropriate sections in the Workshop Manual for installation instructions. 19. Install the oil coolant module onto the engine. Refer to section "Installation of the Oil Coolant Module". NOTE: The oil pan must be thoroughly cleaned when debris has contaminated the engine lubrication system. The engine could be contaminated again if debris is allowed to remain in the sump and circulate. 20. Remove the oil pan, if not already removed. Refer to section "Removal of the Oil Pan". 21. Place a drain pan under the engine to catch oil from the flushing procedure. 22. Using a 17 mm Allen tool, remove the Allen head plug from the oil priming port (1) on the oil coolant module. 14 All information subject to change without notice. Copyright 2018 DETROIT DIESEL CORPORATION
13 If equipped with an oil sample valve at the oil priming port, remove the valve and sealing washer NOTE: Tool J is used to adapt the J oil pre-lube kit for use on a DD platform heavy duty engine. 24. Install the oil priming adaptor (J-49181) into the oil priming port in the oil coolant module. Hand-tighten the adaptor. NOTICE: If chassis application prevents access, a 45-degree or 90-degree pipe fitting (1/4" NPT) can be used as an adaptor. 25. Attach the engine pre-lube kit (J-45299) to the oil priming adaptor. 26. Fill the canister with eight quarts of clean engine oil, meeting the operating requirements of the engine. 27. Open the valve on the primer and start pumping until the container is almost empty. 28. The engine lubrication system has now been flushed. 29. Close the valve on the primer and loosen the fitting; do not completely remove it from the adaptor. 30. Remove the priming adaptor from the oil coolant module with the primer line attached to keep the oil from flowing out of the module. 31. Install the Allen head plug or oil sample valve into the oil coolant module and torque to 70 to 80 N m (51 to 59 lb ft). 32. Continue with the necessary repairs to the engine. Refer to the appropriate section(s) in the applicable Workshop Manual. All information subject to change without notice Copyright 2018 DETROIT DIESEL CORPORATION
Additions, Revisions, or Updates
11 01-14 1 11 01-14 SUBJECT DATE DD15 and DD16 Cylinder Head November 2014 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0081 DDC-SVC-MAN-0181 DDC-SVC-MAN-S181
More informationAftertreatment System December Removal of the 1-BOX from the Vehicle. Installation of the 1- BOX to the Vehicle
12 13-18 1 12 13-18 SUBJECT DATE Aftertreatment System December 2018 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change Removal of the 1-BOX from the Vehicle Installation
More informationAdditions, Revisions, or Updates
1 3 03-15 SUBJECT DATE Contaminated Fluids March 2015 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0084 DD Platform Fuel in Oil This is a new section.
More informationExhaust Gas Recirculation Crossover Pipe December Description and Operation of the EGR Crossover Pipe (Cast)
1 12 12-18 SUBJECT DATE Exhaust Gas Recirculation Crossover Pipe December 2018 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change Description and Operation of the
More informationNUMBER: S.M. REF.: Listed in Table 1 ENGINE: DD13 DATE: October 2009
NUMBER: 10 09 09 S.M. REF.: Listed in Table 1 ENGINE: DD13 DATE: October 2009 SUBJECT: INTERMEDIATE FRAME / FUEL INJECTOR WIRING HARNESS ADDITIONS, REVISIONS, OR UPDATES Publication Number Platform Section
More informationAdditions, Revisions, or Updates
1 02 06-16 SUBJECT DATE Fuel Rail - Three-Filter System February 2016 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0082 DD Platform - All Years
More informationRemoval and Installation of the DD15 and DD16 Cylinder Head April Removal of the DD15 and DD16 Cylinder Head
4 102-12 1 4 102-12 SUBJECT DATE Removal and Installation of the DD15 and DD16 Cylinder Head April 2012 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0081
More informationEPA10 DOC Inlet Pressure Sensor November Removal of the EPA10 Diesel Oxidation Catalyst Inlet Pressure Sensor. without Sensor Box
11 10-14 1 11 10-14 SUBJECT DATE EPA10 DOC November 2014 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change Removal of the EPA10 DDC-SVC-MAN-0083 EPA10 DD Platform
More informationHydrocarbon Fuel Doser Injector Valve Fuel Supply Line December Publication Number / Title Platform Section Title Change
1 SUBJECT DATE Hydrocarbon Fuel Doser Injector Valve Fuel Supply Line December 2016 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change Removal of the Hydrocarbon
More informationFuel Injection System Low Pressure Leak Test Two-Filter Fuel System. Potential Fuel Leak Points Two-Filter. System
10 67-12 1 10 67-12 SUBJECT Fuel Injection System Low Pressure Leak Test, Potential Fuel Leak Points, Alternative Contrast Spray Method for Determining a Leak Path, Alternative Fuel Dye Method for Determining
More informationHow to Replace the Lubricating Oil and Oil Filter October How to Replace the Lubricating Oil and Oil Filter
10 22-16 1 10 22-16 SUBJECT DATE How to Replace the Lubricating Oil and Oil Filter October 2016 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0080
More informationNUMBER: S.M. REF.: Listed in Table ENGINE: EPA07 MBE 4000 DATE: August 2009
NUMBER: 8 5 09 S.M. REF.: Listed in Table ENGINE: EPA07 MBE 4000 DATE: August 2009 SUBJECT: CYLINDERHEADCOOLANTVENTLINE ADDITIONS, REVISIONS, OR UPDATES Publication Number Platform Section Title Change
More informationBelt Drive January Platform Section Title Change. Description and Operation of the Belt Drive Tensioner System. Removal of the Belt Tensioner
1 01 06-18 SUBJECT DATE Belt Drive January 2018 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0190 DDC-SVC-MAN-0081 GHG17 DD Heavy Duty DD Heavy
More informationAdditions, Revisions, or Updates
1 SUBJECT DATE Camshaft Housing Assembly March 2014 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change Removal of the Camshaft Housing DDC-SVC-MAN-0081 DD Platform
More informationOil Pan July DDC-SVC-MAN-0081 DD Platform Installation of the Oil Pan Added graphics, additional torque specs.
7 17-13 1 7 17-13 SUBJECT DATE Oil Pan July 2013 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0081 DD Platform Installation of the Oil Pan Added
More informationNUMBER: S.M. REF.: Listed in Table ENGINE: EPA07 Series 60 DATE: October 2012 SUBJECT: REFERENCES TO THE TURBOCHARGER PURGE ROUTINE
NUMBER: 10 01 12 S.M. REF.: Listed in Table ENGINE: EPA07 Series 60 DATE: October 2012 SUBJECT: REFERENCES TO THE TURBOCHARGER PURGE ROUTINE ADDITIONS, REVISIONS, OR UPDATES Publication Number Platform
More informationGHG14 DD15 Asymmetrical Turbocharger May Removal of the GHG14 DD15 Asymmetrical Turbocharger
5 31-13 1 5 31-13 SUBJECT DATE GHG14 DD15 Asymmetrical Turbocharger May 2013 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change Removal of the GHG14 DD15 Asymmetrical
More informationRemoval and Installation of the Camshaft Housing Assembly February Removal of the Camshaft Housing Assembly
1 SUBJECT DATE Removal and Installation of the Camshaft Housing Assembly February 2014 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change Removal of the Camshaft
More informationCylinder Liner January Removal of the Cylinder Liner. Cleaning of the Cylinder Liner. Inspection of the Cylinder Liner
01 18-16 1 01 18-16 SUBJECT DATE Cylinder Liner January 2016 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change Removal of the Cylinder Liner Added information to
More informationAdditions, Revisions, or Updates
1 2 07-13 SUBJECT DATE Removal and Installation of the Camshaft Housing February 2013 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0081 EPA07/10/
More informationFIS Low Pressure Leak Test March Publication Number / Title Platform Section Title Change. FIS Low Pressure Leak Test- Three-Filter Fuel System
1 3 02-13 SUBJECT DATE FIS Low Pressure Leak Test March 2013 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0084 DD Platform FIS Low Pressure Leak
More informationRemoval of the Needle, Amplifier, and Pressure Limiting Valve Return Lines Three-Filter System
1 5 02-13 SUBJECT Needle, Amplifier, and Pressure Limiting Valve Return Lines Three- Filter System, Fuel Rail - Three-Filter System DATE February 2013 Additions, Revisions, or Updates Publication Number
More informationSection 7.3 Water Manifold has been updated.
NUMBER: 08 DD15-11 S.M. REF.: 7.3 ENGINE: DD15 DATE: September 2008 SUBJECT: WATER MANIFOLD PUBLICATION: DDC-SVC-MAN-0002 Section 7.3 Water Manifold has been updated. 7.3 WATER MANIFOLD Coolant flows from
More informationAdditions, Revisions, or Updates
2 27-14 1 2 27-14 SUBJECT DATE SPN 4335/FMI 7 - EPA10 February 2014 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0084 DD Platform SPN 4335/FMI 7
More informationNUMBER: S.M. REF.: Listed in Table ENGINE: DD15 DATE: March 2009
NUMBER: 3 3 09 S.M. REF.: Listed in Table ENGINE: DD15 DATE: March 2009 SUBJECT: FUEL FILTER ADDITIONS, REVISIONS, OR UPDATES Publication Number Platform Section Title Change Page Number(s) DDC-SVC-MAN-0037
More informationSymptom Diagnostics - Belt Coming Off, Shredding or Misalignment September Symptom Diagnostics - Belt Coming Off, Shredding or Misalignment
09 02-16 1 09 02-16 SUBJECT DATE Symptom Diagnostics - Belt Coming Off, Shredding or Misalignment September 2016 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change
More informationPublication Number / Title Platform Section Title Change. Description and Operation of the Diesel Particulate Filter End Cap
04 04-18 1 04 04-18 SUBJECT GHG17 DD8 - Aftertreatment Systems - Diesel Particulate Filter End Cap DATE April 2018 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change
More informationAdditions, Revisions, or Updates
1 10 18-16 SUBJECT DATE Symptom Diagnostics - Noise October 2016 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change EPA07/10/ DDC-SVC-MAN-0084 GHG14 DD Platform Overhead
More informationAdditions, Revisions, or Updates
6 22-12 1 6 22-12 SUBJECT DATE SPN 4335/FMI 1 - EPA10 June 2012 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0084 EPA10 DD Platform SPN 4335/FMI
More informationAdditions, Revisions, or Updates
1 02 23-16 SUBJECT DATE Diesel Oxidation Catalyst Air Cleaning February 2016 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0084 DDC-SVC-MAN-0191
More informationAdditions, Revisions, or Updates
1 8 05-12 SUBJECT DATE SPN 4354/FMI 5, 4356/FMI 5, 4355/FMI 5, 4357/FMI 5 August 2012 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change SPN 4354/FMI 5 DDC-SVC-MAN-0084
More informationNUMBER: S.M. REF.: Listed in Table 1 ENGINE: DD13 DATE: July 2009
NUMBER: 7 4 09 S.M. REF.: Listed in Table 1 ENGINE: DD13 DATE: July 2009 SUBJECT: EXHAUST GAS RECIRCULATION COOLER WATER MANIFOLD ASSEMBLY ADDITIONS, REVISIONS, OR UPDATES Publication Number Platform Section
More informationRemoval and Installation of the Fuel Injector Cup February Removal of the Fuel Injector Cup Three-Filter System and Two-Filter System
1 2 25-14 SUBJECT DATE Removal and Installation of the Fuel Injector Cup February 2014 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change Removal of the Fuel Injector
More informationAdditions, Revisions, or Updates
1 3 06-13 SUBJECT DATE Potential Fuel Leak Points - Two-Filter Fuel System DD Platform March 2013 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change Potential Fuel
More informationAdditions, Revisions, or Updates
1 8 04-12 SUBJECT DATE SPNs 4354/FMI 5, 4355/FMI 5, 4356/FMI 5, 4357/FMI 5 August 2012 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change SPN 4354/FMI 5 DDC-SVC-MAN-0084
More informationNUMBER: S.M. REF.: Listed in Table ENGINE: DD Platform DATE: May 2010
NUMBER: 5 04 10 S.M. REF.: Listed in Table ENGINE: DD Platform DATE: May 2010 SUBJECT: FUEL SYSTEM PRIMING USING ESOC 350 FUEL PRIMING PUMP ADDITIONS, REVISIONS, OR UPDATES Publication Number Platform
More informationPiston and Connecting Rod Assembly January Removal of the Piston and Connecting Rod Assembly
1 18-13 1 1 18-13 SUBJECT DATE Piston and Connecting Rod Assembly January 2013 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change Removal of the Piston and Connecting
More informationPiston and Connecting Rod Assembly August Removal of the Piston and Connecting Rod Assembly
1 8 17-13 SUBJECT DATE Piston and Connecting Rod Assembly August 2013 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change Removal of the Piston DDC-SVC-MAN-0081 DD
More informationAdditions, Revisions, or Updates
1 3 26-15 SUBJECT DATE Main Shaft Speed Sensor March 2015 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0140 Transmission Removal of the Main Shaft
More informationPublication Number / Title Platform Section Title Change. Removal of DD15 and DD16 Delphi Exhaust Gas Recirculation Valve Actuator
7 02-15 1 7 02-15 SUBJECT DD15 and DD16 Delphi Exhaust Gas Recirculation Valve Actuator and DD15 and DD16 Sonceboz Exhaust Gas Recirculation Valve Actuator DATE July 2015 Additions, Revisions, or Updates
More informationExhaust and Exhaust Gas Recirculation September Testing of the DD13. Exhaust Gas Recirculation Cooler Water Manifold Assembly - In Chassis
1 09 04-16 SUBJECT DATE Exhaust and Exhaust Gas Recirculation September 2016 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change Testing of the DD13 DDC-SVC-MAN-0190
More informationAdditions, Revisions, or Updates
1 01 06-15 SUBJECT DATE SPN 3251 (ACM) (EPA10) and (GHG14) January 2015 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change SPN 3251/FMI 0 - GHG14 DDC-SVC-MAN-0084
More informationInstallation of the DD13,DD15, and DD16 Cylinder Head February Installation of the DD13 Cylinder Head
5 02-12Rev 1 5 02-12Rev SUBJECT DATE Installation of the DD13,DD15, and DD16 Cylinder Head February 2013 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change Installation
More informationAdditions, Revisions, or Updates
1 2 22-14 SUBJECT DATE SPN 4334/FMI 7 (ACM) (EPA10) February 2014 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0084 DD Platform - EPA10- ACM SPN
More informationEngine Replacement Procedures September Removal of the Complete Powertrain Assembly. Replacement Long Block Engine Preparation
9 05-15 1 9 05-15 SUBJECT DATE Engine Replacement Procedures September 2015 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change Removal of the Complete Powertrain
More informationCamshaft and Idler Gear August Removal of the Camshafts. Installation of the Camshafts. Removal of the Intake Rocker Shaft Assembly
08 11-16 1 08 11-16 SUBJECT DATE Camshaft and Idler Gear August 2016 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change Removal of the Camshafts Added notice and
More informationHigh Pressure Fuel Rail Feed Lines September Platform Section Title Change
9 10-14 1 9 10-14 SUBJECT DATE High Pressure Fuel Rail Feed Lines September 2014 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0082 DDC-SVC-MAN-0182
More informationEGR Actuator Slow Learn April Installation of the DD13 Exhaust Gas Recirculation Valve Actuator Pull Rod
1 4 07-13 SUBJECT DATE EGR Actuator Slow Learn April 2013 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0083 Installation of the DD13 Exhaust Gas
More informationInstallation of the Fuel Rail -Three-Filter System January Publication Number / Title Platform Section Title Change
1 1 20-13 SUBJECT DATE Installation of the Fuel Rail -Three-Filter System January 2013 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change Installation of the Fuel
More informationNotice Added to Sections Listed Below February Removal of the Bypass Valve. Removal of the Pressure Relief Valve
2 15-12 1 2 15-12 SUBJECT DATE Notice Added to Sections Listed Below February 2012 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0082 Removal of
More informationEGR Actuator May Description and Operation of the DD13 Exhaust Gas Recirculation Valve Actuator
5 17-13 1 5 17-13 SUBJECT DATE EGR Actuator May 2013 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change Description and Operation of the DD13 Exhaust Gas Recirculation
More informationAdditions, Revisions, or Updates
1 5 03-14 SUBJECT DATE SPN 3599/FMI 3 and 4 (ACM) May 2014 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change SPN 3599/FMI 3-1 DDC-SVC-MAN-0084 EPA10/ GHG14 DD Platform
More informationFuel Filter Maintenance Intervals July EPA10/GHG14 DD Series Preventive Maintenance Tables
1 7 14-13 SUBJECT DATE Fuel Filter Maintenance Intervals July 2013 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0080 EPA10/ GHG14 DD Platform EPA10/GHG14
More informationPage 1 of 12 Section 2.3 N2 Electronic Unit Injector The N2 Electronic Unit Injector (EUI) is a lightweight, compact unit that injects diesel fuel directly into the combustion chamber. See Figure "N2 Electronic
More informationAdditions, Revisions, or Updates
1 06 10-16 SUBJECT SPN 111 (CPC) (GHG17) and SPN 111 (CPC) (EPA07;EPA10;GHG14) DATE June 2016 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0191
More information4.2 WATER PUMP (GEAR CASE MOUNTED AND LATER) (GCM)
SERIES 60 SERVICE MANUAL 4.2 WATER PUMP (GEAR CASE MOUNTED - 1991 AND LATER) (GCM) The centrifugal-type water pump circulates the engine coolant through the cooling system. The pump is mounted on the rear
More informationAdditions, Revisions, or Updates
1 1 38-13 SUBJECT DATE Inspection of the Main and Connecting Rod Bearings In-Chassis January 2013 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change Inspection of
More informationPublication Number / Title Platform Section Title Change. Removal of the High Pressure Fuel Pump Drive Gear - Three-Filter System
5 34-13 1 5 34-13 SUBJECT Removal and Installation of the High Pressure Fuel Pump Drive Gear - Three-Filter System DATE June 2013 Additions, Revisions, or Updates Publication Number / Title Platform Section
More informationMBE 900 and MBE 4000 EGR Cooler Leak Tester
TO: FROM: SUBJECT: Service Locations Technical Support Development MBE 900 and MBE 4000 EGR Cooler Leak Tester No.: 06 TL 03rev September 20, 2006 ISSUE Detroit Diesel has released an EGR cooler test kit
More informationPublication Number / Title Platform Section Title Change SPN 5246/FMI 0- EPA10 SPN 5246/FMI 15 - EPA10 SPN 5246/FMI 16 - EPA10 SPN 5246/FMI 0 - GHG14
1 3 04-14 SUBJECT SPN 5246/FMI 0, 15, 16 (ACM2)(EPA10) SPN 5246/FMI 0, 15, 16 (ACM2.1)(GHG14) DATE March 2014 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change SPN
More informationAdditions, Revisions, or Updates
1 8 22-13 SUBJECT DATE Water Manifold Assembly August 2013 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change Installation of the DD13 EGR Cooler Water DDC-SVC-MAN-0081
More informationNUMBER: S.M. REF.: Listed in Table ENGINE: EPA07 Series 60 DATE: August 2013 SUBJECT: VALVE LASH ADJUSTMENTS ADDITIONS, REVISIONS, OR UPDATES
NUMBER: 8 34 13 S.M. REF.: Listed in Table ENGINE: EPA07 Series 60 DATE: August 2013 SUBJECT: VALVE LASH ADJUSTMENTS ADDITIONS, REVISIONS, OR UPDATES Publication Number Platform Section Title Change DDC-SVC-MAN-0005
More informationSection 1.26 Camshaft Gear Assembly Series 60 Exhaust Gas Recirculation (EGR) Model
Page 1 of 22 Section 1.26 Camshaft Gear Assembly Series 60 Exhaust Gas Recirculation (EGR) Model Series 60 EGR uses a camshaft gear assembly. Camshaft, camshaft drive gear and camshaft gear cover are the
More informationAdditions, Revisions, or Updates
6 08-15 1 6 08-15 SUBJECT DATE NOx Sensors June 2015 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change Removal of the GHG14 1-BOX Aftertreatment DDC-SVC-MAN-0083
More information18SP653 EPA04 and EPA98 MBE 4000 High Pressure Fuel Line and Transfer Tube Installation
18SP653 EPA04 and EPA98 MBE 4000 High Pressure Fuel Line and Transfer Tube Installation KIT DESCRIPTION A service kit (P/N: A4600700135) is now available to install EPA07 high pressure fuel injector lines
More informationAdditions, Revisions, or Updates
1 5 33-13 SUBJECT Removal and Installation of the High Pressure Fuel Pump -Three- Filter System DATE May 2013 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change Removal
More informationAdditions, Revisions, or Updates
1 10 09-14 SUBJECT DATE SPN 5016 (ACM) (GHG14) October 2014 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change SPN 5016/FMI 3 - DDC-SVC-MAN-0084 GHG14 DD Platform
More informationAdditions, Revisions, or Updates
1 6 05-13 SUBJECT DATE SPN 625/FMI 9 EPA10 - GHG14 June 2013 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0084 EPA10/ GHG14 DD Platform SPN 625/FMI
More informationNUMBER: S.M. REF.: Refer to 2.5 ENGINE: 60 DATE: January 2007
NUMBER: 1 60 07 S.M. REF.: Refer to 2.5 ENGINE: 60 DATE: January 2007 SUBJECT: N3 ELECTRONIC INJECTOR PUBLICATION: 6SE483 The Series 60 Service Manual has been revised. Engine models built from December
More informationPoly-V-Belts February Description and Operation of the Poly-V- Belts. Removal of the Poly-V- Belts. Inspection of the Poly-V- Belts
1 02 13-18 SUBJECT DATE Poly-V-Belts February 2018 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change Description and Operation of the Poly-V- Belts DDC-SVC-MAN-0190
More informationAdditions, Revisions, or Updates
1 01 11-16 SUBJECT DATE SPN 647 (MCM)(EPA07-EPA10-GHG14) January 2016 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0084 DDC-SVC-MAN-S084 DD Platform
More informationAdditions, Revisions, or Updates
1 9 52-12 SUBJECT DATE High Pressure Fuel System - Leak Test - Two Filter System October 2012 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0084
More informationAdditions, Revisions, or Updates
1 12 02-12 SUBJECT DATE Test E - Three-Filter Fuel System December 2012 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0084 DD Platform Test E - Three-Filter
More informationAdditions, Revisions, or Updates
1 9 04-11 SUBJECT DATE SPN 3250 / FMI 16 DOC Outlet Temperature High August 2011 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0084 EPA07 DD13/DD15
More informationNUMBER: S.M. REF.: 8.5 ENGINE: EPA07 Series 60 DATE: November 2008
NUMBER: 08 60-7 S.M. REF.: 8.5 ENGINE: EPA07 Series 60 DATE: November 2008 SUBJECT: EGR RATE MEASUREMENT SYSTEM PUBLICATION: DDC-SVC-MAN-0005 EGR Rate Measurement System has new information added. EGR
More informationSPN 3480 (MCM)(EPA07;EPA10;GHG14) June Publication Number / Title Platform Section Title Change
6 06-15 1 6 06-15 SUBJECT DATE SPN 3480 (MCM)(EPA07;EPA10;GHG14) June 2015 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change Revised step 3,14, and 29. DDC-SVC-MAN-0084
More informationAdditions, Revisions, or Updates
1 03 12-17 SUBJECT DATE SPN 157 (MCM) GHG17 March 2017 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0193 DD Platform - Med Duty SPN 157/FMI 16 -
More informationAdditions, Revisions, or Updates
1 03 13-17 SUBJECT DATE SPN 520268 (MCM) (GHG17) March 2017 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0193 DD Platform Med Duty SPN 520268/ FMI
More informationAdditions, Revisions, or Updates
1 01 29-14 SUBJECT DATE SPN 3511/FMI 3 and 4 - GHG14 January 2014 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change SPN 3511/FMI 3 - DDC-SVC-MAN-0084 GHG14 DD Platform
More informationSPN 3480/FMI 0, 1, 3, 4, 14, 21, 31 October 2012 SPN 3480/FMI 0 SPN 3480/FMI 1 SPN 3480/FMI 3 SPN 3480/FMI 4 SPN 3480/FMI 14 SPN 3480/FMI 21
1 10 85-12 SUBJECT DATE SPN 3480/FMI 0, 1, 3, 4, 14, 21, 31 October 2012 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change SPN 3480/FMI 0 SPN 3480/FMI 1 DDC-SVC-MAN-0084
More informationTest A - Three-Filter and Two-Filter Fuel Systems March Test A - Three-Filter Fuel System. Test A - Two-Filter Fuel System
1 3 37-14 SUBJECT DATE Test A - Three-Filter and Two-Filter Fuel s March 2014 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change Test A - Three-Filter Fuel DDC-SVC-MAN-0084
More informationSymptom Diagnostics - Hard Start/No Start April Hard Start/No Start - Two-Filter Fuel System (This Test Must Be Done First)
04 10-17 1 04 10-17 SUBJECT DATE Symptom Diagnostics - Hard Start/No Start April 2017 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change Hard Start/No Start - Two-Filter
More informationThe EPA07 Series 60 Workshop Manual has been revised. Listed in Table 1 are the revisions.
NUMBER: 08 60-6 S.M. REF.: 2.3.1 and 2.3.2 ENGINE: EPA07 Series 60 DATE: September 2008 SUBJECT: E3 INJECTOR TUBE PUBLICATION: DDC-SVC-MAN-0005 The EPA07 Series 60 Workshop Manual has been revised. Listed
More informationAdditions, Revisions, or Updates
1 SUBJECT DATE SPN 51/FMI 10 and 18 March 2014 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0084 GHG14 DD Platform SPN 51/FMI 10 SPN 51/FMI 18 The
More information18SP631 MBE 4000 Oil Gallery Threaded Plug Installation
18SP631 MBE 4000 Oil Gallery Threaded Plug Installation KIT DESCRIPTION A new service kit (P/N: 23536501) is now available to install two threaded plugs in place of cup plugs in the rear oil gallery on
More informationNUMBER: S.M. REF.: Listed in Table ENGINE: EPA07 Series 60 DATE: June 2012 SUBJECT: E3 FUEL INJECTOR TUBE ADDITIONS, REVISIONS, OR UPDATES
NUMBER: 6 25 12 S.M. REF.: Listed in Table ENGINE: EPA07 Series 60 DATE: June 2012 SUBJECT: E3 FUEL INJECTOR TUBE ADDITIONS, REVISIONS, OR UPDATES Publication Number Platform Section Title Change E3 Fuel
More informationHard Start/No Start - Two-Filter Fuel System (This Test Must Be Done First) Test-A - Two-Filter Fuel System. Test-C - Two-Filter Fuel System
1 SUBJECT DATE Symptom Diagnostics - Hard Start/No Start - Two-Filter Fuel System June 2013 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change Hard Start/No Start
More informationHigh pressure fuel line and transfer tube removal and installation procedures have been updated.
NUMBER: 08 MBE 4000-3 S.M. REF.: 2.3 ENGINE: EPA04 MBE 4000 DATE: July 2008 SUBJECT: HIGH PRESSURE FUEL LINE AND TRANSFER TUBE PUBLICATION:DDC-SVC-MAN-0023 High pressure fuel line and transfer tube removal
More informationNUMBER: S.M. REF.: Listed in Table ENGINE: EPA07 Series 60 DATE: April 2009
NUMBER: 4 7 09 S.M. REF.: Listed in Table ENGINE: EPA07 Series 60 DATE: April 2009 SUBJECT: SPN 27 ADDITIONS, REVISIONS, OR UPDATES Publication Number Platform Section Title Change Page Number(s) DDC-SVC-MAN-0009
More informationEGR heater plate removal and installation procedure has been added.
NUMBER: 08 60-3 S.M. REF.: 8.3 ENGINE: EPA07 Series 60 DATE:June 2008 SUBJECT: EGR HEATER PLATE PUBLICATION: DDC-SVC-MAN-0005 EGR heater plate removal and installation procedure has been added. 8.3.1 REMOVAL
More informationAdditions, Revisions, or Updates
1 8 02-14 SUBJECT DATE SPN 4334 (ACM) (GHG14) August 2014 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change SPN 4334/FMI 3 - DDC-SVC-MAN-0084 GHG14 DD Platform GHG14
More informationAdditions, Revisions, or Updates
1 01 06-16 SUBJECT SPN 4334/FMI 4 (ACM) (GHG14) SPN 4334/FMI 4 (ACM) (GHG17) DATE January 2016 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0084
More informationRev Rev. Additions, Revisions, or Updates
1 4 89-12Rev SUBJECT DATE SPN 5927/FMI 2 and 7 - GHG14 April 2012 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change SPN 5927/FMI 2 - DDC-SVC-MAN-0084 DD Platform
More information18SP712 EPA07 DD15/16 Three-Filter Fuel System to Two-Filter KM59 GEN1 Fuel System Conversion Service Kit (P/N: A )
18SP712 EPA07 DD15/16 Three-Filter Fuel System to Two-Filter KM59 GEN1 Fuel System Conversion Service Kit (P/N: A4710901055) KIT DESCRIPTION This service kit includes all necessary parts to convert the
More informationPerform the following procedures for removal and installation of the protective sleeve.
MBE 4000 SERVICE MANUAL 2.6 PROTECTIVE SLEEVE Perform the following procedures for removal and installation of the protective sleeve. 2.6.1 Protective Sleeve Removal Remove the protective sleeve as follows:
More information18SP720 EPA10 DD15/16 Three-Filter ESOC Fuel System to Two-Filter KM59 GEN1 Fuel System Conversion Service Kit (P/N: A )
18SP720 EPA10 DD15/16 Three-Filter ESOC Fuel System to Two-Filter KM59 GEN1 Fuel System Conversion Service Kit (P/N: A4710901455) KIT DESCRIPTION This service kit includes all necessary parts to convert
More informationAdditions, Revisions, or Updates
1 02 01-14 SUBJECT DATE SPN 1761/FMI 3, 4 ( ACM2-EPA10) (ACM2.1-GHG14) February 2014 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0084 DD Platform
More information18SP684Rev2 EPA07 and EPA10 DD Platform EGR Delta Pressure Sensor Update
18SP684Rev2 EPA07 and EPA10 DD Platform EGR Delta Pressure Sensor Update NOTE: This kit is to be used ONLY if the venturi pipe is plugged. KIT DESCRIPTION Two service kits have been released containing
More informationAdditions, Revisions, or Updates
1 SUBJECT DATE SPN 3250/FMI 0, 15 - EPA10 October 2012 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change SPN 3250/FMI 0 - DDC-SVC-MAN-0084 EPA10 DD Platform EPA10
More informationSPN 3509 (MCM) (EPA10) and SPN 3509 (MCM) (GHG14) June 2014 SPN 3509/FMI 3 - EPA10 SPN 3509/FMI 4 - EPA10 SPN 3509/FMI 3 - GHG14
1 SUBJECT DATE SPN 3509 (MCM) (EPA10) and SPN 3509 (MCM) (GHG14) June 2014 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change SPN 3509/FMI 3 - EPA10 The diagnostic
More information