Table of Contents. LP_2200 Features & Benefits 3/20/14

Transcription

1 LP_2200 & 3/20/14

2 Table of Contents (Go to 2nd Page) Table of Contents (Continued on next page) Land Pride Aerators, Core CA05 Series CA15 Series CA25 Series Pasture AR2596 & AR2510 Models All Flex Mowers AFM4211 Models AFM4214 & AFM4216 Models AFM4522 Model Angle Broom Model AB Bale Spears BS & BSE Series Blades, Front TB2596 & TB25108 Models Rear RB05 Series RB15 Series RB16 & RB26 Series RB37 Series RBT35 Series RBT40 Series RBT45 Series RBT55120 Model RBT60 Series Box Scrapers BB05 Series BB12 Series BB15 & BB25 Series MR15 & HR25 Series (Retractable) HRL3578 & HR3584 Models (Retractable) Compact Drills P500 & 3P600 Models P500V Model NT Model P606NT Model Model P806NT Model P1006NT Model Disc Harrows DH10 Series DH15 Series DH25 Series DH35 Series Ditchers DT35 Model DT55 & DTM55 Models Drag Harrows DRG Series Drag Scraper BB4596, BB4510 & BB Flail Mowers FM21 Series FM31 & FM41 Series Grading Scrapers GS15 Series GS25 Series Grapples, Claw SGC0548 Model SGC10 Series SGC15 Series SGC20 Series Manure SGM15 Series Rock SGR15 Series Skeleton SGS15 Series Grapple Buckets, Rock & Skeleton SRB15 & SSB15 Series Grooming Mowers, Rear Discharge FDR16 Series FDR25 Series FDR3690 Model Hydraulic Reservoir System HRS18 & HRS HRS Landscape Rakes LR05 Series LR16 & LR26 Series LR36 Series Pallet Forks PF10 & PF20 Series PFL20, PFL30, PFL45, PFL55, & PFL64 Series 57 Copyright 2013 All rights Reserved Land Pride provides this publication as is without warranty of any kind, either expressed or implied. While every precaution has been taken in the preparation of this manual, Land Pride assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use of the information contained herein. Land Pride reserves the right to revise and improve its products as it sees fit. This publication describes the state of this product at the time of its publication, and may not reflect the product in the future. Land Pride is a registered trademark. All other brands and product names are trademarks or registered trademarks of their respective holders. Printed in the United States of America. 6/25/13

3 Table of Contents (Go to 1st Page) Land Pride Post Hole Diggers, PTO PD10 Model PD15 Model PD25 & PD35 Model Hydraulic HD25 & HD35 Series (3-Point) SA35 Model (Skid Steer) Powered Rakes PR16 Series (3-Point) SR26 Series (Skid Steer) Quick Hitches QH15 & QH20 Series SH35 Series (Skid Steer) Rotary Cutters, Single Deck RCD1884 Model RCF2060 & RCF2072 Models RCF2084 Model RCF2760 & RCF2772 Models RCF2784 Model RCF3096 & RCF(M)3010 Models RCF3660 & RCF3672 Models RCF3684 Model RCF(M)3696 & RCF(M)3610 Models RCR12 Series RCR15 Series RCR1860 & RCR1872 Models RCR1884 Model RCR2596 & RCR25(M)10 Models RCR2660 and RCR2672 Models RCR2684 Model RCP(M)26 & RCP(M)30 Series (Parallel Arm). 82 SC26 Series (Skid Steer) Folding Deck RC2512 Model RC2515 Model RC3614 & RCM3614 Models RC3615 and RCM3615 Models RC3620 & RCM3620 Models RC4015 and RCM4015 Models RC5014 & RCM5014 Models RC5020 & RCM5020 Models RC(M)5510 & RC(M)6510 Models RC(M)5515 & RC(M)6515 Models RC(M)5610 & RC(M)6610 Models RC(M)5615 & RC(M)6615 Models RCB6610 & RCBM6610 Models RCB6615 & RCBM6615 Models Rotary Tillers RTR05 Series RTA12 Series RTR12 Series RTA15 Series RTR15 Series RTA20 & RTR20 Series RTA25 & RTA35 Series RTR2570 Model Scarifiers SF25 Series Seed Bed Roller SBR Series Seeders, All Purpose Seeder APS15 Series Food Plot Seeder FPS48 Plot Ranger Electric Spin Spreader Electric Spin Spreader Overseeder OS15 Series Primary Seeder PS1572 Model PSN2096 Model PS25120 Model Spreaders FSP500, FSP700 & FSP1000 Models PFS4000, PFS5060 & PFS8010 Models PTS500 & PTS700 Models Snow Blowers SB10, SB15, & SB25 Series SBD3596 & SBD35108 Models Soil Pulverizers SP20 & SP30 Series Spike Tooth Harrows STH1590 Model STH2024 Model Straw Crimpers CR25 Series Stump Grinders, Skid Steer SSG2524 Model Wood Chippers WC WC Zero Turn Mowers Z48, Z54, ZSR54 & ZSR60 Models ZST40 & ZST48 Models ZT360 & ZT372 Models /25/13

4 Aerators, Core and Table of Contents Aerators, Core CA05 Series Pull Type Clevis Hitch Fits behind any small tractor, lawn tractor, utility vehicle or ATV with a pull tongue. 3 Sizes 40", 48" & 56" Great sizes for residential home owners and other light applications. Formed 10 Ga. end panels Offers good strength and appearance. and center supports Formed 12 Ga. weight tray with drain holes 16 Ga. x 1/2" I.D. hardened spring steel spoons with beveled edge Individual Spoon Replacement Adds safety over spoon area, doesn t allow foreign weight object to fall into spoon area, keeps cores from being thrown forward. Penetrates the ground easier than spoons constructed of a heaver gage material and/or larger diameter bodies. Requires removal of only two bolts to replace a worn-out spoon. Don t have to disassemble the whole rotor section to get to the spoons. Gang greasing Each gang has a grease zerk for smooth rotation. 8 1/2" Spoon spacing (forward travel) Offers optimum core pulling pattern & aeration. 4" Spoon spacing laterally 4.2 Aeration cores per sq. ft. Provides good aeration per square foot. Weight tray Additional weight can be easily added to the aerator. 11/25/ F 1

5 and Aerators, Core CA15 Series Cat. 0, Cat. 1 and Fits many of the smaller tractors and fits Land Pride Quick-Hitch Cat. 1 Limited Hitch 4 Sizes 48", 56", 64" & 72" Great sizes for small landscapers, golf courses, campuses and cities. Formed 10 Ga. mainframe and Formed 10 Ga. plates offers good strength and appearance. rotary supports Expanded metal in weight tray 16 Ga. x 1/2" I.D. harden spring steel spoons with beveled edge Individual Spoon Replacement Adds safety over spoon area, doesn t allow foreign weight object to fall into spoon area, keeps cores from being thrown forward. Penetrates the ground easier than spoons constructed of a heaver gage material and/or larger diameter bodies. Requires removal of only two bolts to replace a worn-out spoon. Don t have to disassemble the whole rotary section to get to the spoons. 4 1/2" Gang spacing Offers optimum core pulling pattern. Spoon gangs Spoon gangs are independent of each other allowing for less side load torque on each gang and tearing of the turf during turns. Spoon gang greasing Each gang has a grease zerk for smooth rotation. 3 - Storage stands Keeps the spoons off the ground while in storage and aids in hooking-up to the tractor. 6 3/16" Spoon spacing forward Offers optimum aeration. travel 48" = 4.5 Aeration cores per sq. ft. Provides good aeration per square foot. 56" = 4.7 Aeration cores per Sq. ft. 64" = 4.8 Aeration cores per Sq. ft. 72" = 5.0 Aeration cores per Sq. ft. Weight tray Additional weight can be easily added to the aerator. 2

6 and Aerators, Core CA25 Series 2 Sizes 60" & 72" Great sizes for small landscapers to golf courses, campuses, cities. Cat. 1 Hitch Fits Land Pride Quick-Hitch, and stout enough to work with any Cat. 1 tractor. Plate steel A frame Plate steel offers greater strength from natural force applied downward from tractor top link. Tubular Construction 2 1/2" x 2 1/2" x 3/16" Tubing vs. angle iron offers greater strength as well as gives a better appearance. Expanded metal in weight tray Adds safety over spoon area, doesn t allow foreign weight object to fall into spoon area, keeps cores from being thrown forward. Hardened steel spoons 3/4" ID spoons, with 3 mm wall thickness and beveled edge penetrate the ground easier than thicker OD spoons, but are just as strong. Individual Spoon Replacement Requires removal of only two bolts to replace a worn-out spoon. Don t have to disassemble the whole rotary section to get to the spoons. 5 1/2" Gang spacing on 60" units 5 1/2" on 60" Units, 6 1/2" on 72" unit offers optimum core pulling pattern. 6 1/2" Gang spacing on 72" units Spoon gangs Spoon gangs are independent of each other allowing for less side load torque on each gang and tearing of the turf during turns. Spoon gang greasing Each gang has a grease zerk for smooth rotation. Storage stands Each corner has a storage stand to aid in off the ground storing, as well as aiding in hooking to the tractor. Spoon spacing forward travel 7" Spacing in forward travel offers optimum aeration. Sq. foot aeration 4 Cores per sq. ft. on 72" unit, and 6 cores per sq. ft. on 60". Optional Water Tanks Easily add up to 490 lbs. to the 60" and 600 lbs. to the 72" to aid in compacted soil conditions. Can easily reduce weight by draining tank incrementally. Water tanks are safer due to precise fit and fastening vs. stacking inconsistent sized objects and difficulty in uniform fastening. 6/22/ F 3

7 Pasture Table of Contents and Aerators, Pasture All Welded 4 x 4 Tubing Frame 4 x 4 x 5/16 Tongue With Clevis Hitch Forged & Heat Treated Through Steel Tines Tines Bolt-on Tines (2 Bolts Per Tine) AR2596 & AR2510 Models Makes for a very strong frame. Built heavy duty to withstand side loads from the tines. Forged and heat treated tines are very resistant to wear and breakage giving them a long life. Tines are designed with a twist to lift while fracturing the soil sideways. Tines are easily replaceable with 2 bolts per tine. 8" Maximum Tine Penetration Great penetration for aerating the soil. (Actual penetration depth is dependent on ground condition and added weight.) Heavy Duty Rotary Tine Hangers Designed to stand up to the rigors of hard rocky soil. Bearings Are Protected With 3/8" Skid Shoes on 3-Sides Adjustable Rotors 7 1/2" Tine Spacing (4/per Spool) AR2596 = 48 Tines Total AR2510 = 64 Tines Total Optional Weights Constructed of 740 lbs. Concrete Blocks With Lifting Lugs Built In Optional Harrow Lift Package Accessory Drag Harrow Accessory Trailing Hitch Protects bearings against hitting solid objects such as rocks and stumps. (Skid shoe protection is located on the front, bottom and back sides of bearings) Rotors can be adjusted from 2 1/2, 5 and 7 1/2 degrees to meet customers needs. The greater the angle the harsher the shattering of soil. Tines spaced 7 1/2" apart provides good coverage. AR2596 accepts up to 3 concrete blocks and AR2510 accepts up to 4 concrete blocks. Helps Aerator tines penetrate the ground. Lifts the Drag Harrow off the ground for transporting on roadways. Provides a means to smooth out the ground behind the Aerator. Drag Harrow has three positions it can be used: Drag Mat, Light Penetration & Deep Penetration. Hitch is self leveling for pulling implements behind the Aerator. 6/22/ F 4

8 All Flex Mowers Table of Contents and All Flex Mowers AFM4211 Models Counter blade rotation on left hand deck Spreads grass clippings more evenly. Wing decks throw grass away from the rear deck. Rear deck doesn t get covered up nor does it get bogged down by cut grass. 7'-8" transport width Meets most city/county codes for transport width. at lowest cutting height 6" Deck overlap Eliminates skipping when going into a tight turn. 11'-1" Cutting width three 48" decks Sized right for golf courses, cities, schools. Small decks give excellent flexibility. Sleek frame design, including single beam hitch and compact deck overlap Design allows operator to make tighter turns without leaving windrows and skips. AFM virtually becomes a zero turn mower. (Oversized tires may not allow this.) Automatic transport wing locks When wings are raised in the full transport position, the wings lock in place. No need to get off the tractor to lock. Pull rope from tractor seat to un-lock. 18" Transport tires with tapered roller bearings Transport tires offer smooth roading and less grass compaction. Allows grass to stand up. Tapered roller bearings offer longevity. Removable transportation tire spindles Allows a spindle to be replaced by simply removing two bolts. Back wheels on side decks even with Allows tighter turns without skips. transportation tires Rigid rear side deck tires. Rigid wheel yokes holds hills and slopes better. Safer unit than the competition. 13" Deck tires with sealant 13" Tires offer great flotation, less lbs. per square inch. Sealant minimizes flats. 1/4" Gauge wheel arms Gives the cutter gauge wheel arms a great deal of hidden strength. Low pivot points on deck The lower the pivot points are to the ground, the more side to side swing, allowing for excellent flotation from each deck. Deflectors built into mower decks Safety features meet ANSI standards. Many competitors use chains for protection. Once chains are removed the unit does not meet ANSI specifications. Rear discharge Even dispersal, discharged items are aimed downward. No rear chains are needed, which tend to clump damp grass. Rounded front deck edges Helps protect trees and other obstacles. with no protruding skid shoe 5/16" Front edge & all-welded seams Provides extra durability. Cat. 3 Constant velocity main driveline Constant velocity main driveline allows for tighter turns without harming U-joints in driveline, includes slip clutch option. Cat. 2 wing drivelines Reduces start-up torque that is put on the driveline, gearbox and gearbox support. Slip-clutch protection Guards against premature gearbox failure. Protects mower deck spindles. ABS guards No paint to scratch off, lighter weight, no rattling or rust. Heavy gearbox mounts on center Handles start-up torque better. and side mower decks Gearbox HP Rating HP Gearbox warranty 5 years on parts and labor. Demonstrates our confidence in the gearbox s quality and lasting performance. Easy to grease blade spindles No guards to remove for routine greasing of blade spindles. Middle spindle sits towards the back of the mower deck. Uses less horsepower and allows material to escape the mower deck easier. The discharge of material is more even. Design eliminates windrowing. Spring loaded idlers Applies constant tension to belt to run efficiently. Easy belt tension release Easily release belt tension for changing belt or for winter storage. High blade tip speed (16,260 fpm) Lifts grass up for a clean cut and efficient discharge of material. Tip speed rates are as high or higher than the competition. Choice of Blade (Medium lift standard) Others available thru parts dept. Low Lift - Highly recommended in sandy soils where lifting isn t crucial. Disturbs the soil very little, allowing blades to wear longer. Medium Lift - Medium suction for lifting grass. Requires less HP than high lift. High Lift - Greatest suction for lifting grass before cutting. Can take higher HP in tall dense grass. Not recommended in sandy soils. Mulching - Perfect for leaf mulching. Optional Hydraulic Operated Transport Locks Transports locks can be released easily from the tractor seat while operating the same tractor control lever that raises and lowers the mower decks. Eliminates pulling a rope to release transport locks. 4/01/ F 5

9 and All Flex Mowers AFM4214 & AFM4216 Models Counter rotation on left hand deck Spreads grass clippings more evenly. Wing decks throw grass away from the rear deck. Rear deck doesn t get covered up nor does it get bogged down by cut grass. Narrow 6'-8" transport width Not much wider than most tractors, making for safer transport. Meets most city/ county codes for transport width 6" Deck overlap (AFM4214) Eliminates blade skips when turning. Tighter turns can be made. 8" Deck overlap (AFM4216) Allows for maximum amount of wing deck flex. Sleek frame design, including single Design allows operator to make tighter turns without leaving windrows and skips. beam hitch and compact deck overlap The AFM virtually becomes a zero turn mower. Automatic transport wing locks When wings are raised in the full transport position, the wings lock in place, no need to get off the tractor to lock. Pull rope from tractor seat to unlock. 23" Transport tires 23" Transport tires offer smooth roading and less grass compaction. Allows grass with tapered bearings to stand up. Tapered roller bearings offer longevity. Removable transportation tire spindles Allows a spindle to be replaced by simply removing two bolts. Back wheels on side decks even with Allows tighter turns without skips. transportation tires Rigid rear side deck tires Rigid wheel yokes holds hills and slopes better. Safer unit than the competition. Large deck flotation tires with sealant Optional 15" tires for great flotation or 18" tires for even greater flotation. The larger the tire the less compaction in pounds per square inch allowing grass to stand up. Sealant in the tires minimizes flats. 1/4" Gauge wheel arms Gives the cutter gauge wheel arms a great deal of hidden strength. Low pivot points on deck The lower the pivot points are to the ground, the more side to side swing, allowing for excellent flotation from each deck. Deflectors built into mower decks Safety features meet ANSI standards. Many competitors use chains for protection. Once chains are removed the unit may not meet ANSI specifications. Rear discharge Even dispersal, discharged items are always aimed downward. No rear chains are needed, which tend to clump damp grass. Cat. 4 CV main driveline Constant velocity main driveline allows for tighter turns without harming U-joints in driveline, iincludes slip clutch. Cat. 2 wing drivelines Reduces start-up torque that is put on the driveline, gearbox and gearbox support. Slip clutch protection Guards against premature gearbox failure. Protects mower deck spindles. Heavy gearbox mounts on center Handles start up torque. and side mower decks Gearbox HP Rating HP Gearbox warranty 5 years on parts and labor. Demonstrates our confidence in the gearbox s quality and lasting performance. Easy to grease blade spindles No guards to remove for routine greasing of blade spindles. Middle spindle sits towards Uses less horsepower and allows material to escape the mower deck easier. The the back of the mower deck. discharge of material is more even. Design eliminates windrowing. Spring loaded idlers Applies constant tension to belt to run efficiently. Easy belt tension release Easily release belt tension for changing belt or for winter storage. High blade tip speed (AFM4214 = 18,396 fpm & AFM4216 = 18, 340 fpm) Lifts grass up for a clean cut and efficient discharge of material. Tip rates as high or higher than the competition. Choice of Blade Low Lift - Highly recommended in sandy soils where lifting isn t crucial. Disturbs the (Low lift standard) soil very little, allowing blades to wear longer. Others available thru parts dept. Medium Lift - Medium suction for lifting grass. Requires less HP than high lift. High Lift - Greatest suction for lifting grass before cutting. Can take higher HP in tall dense grass. Not recommended in sandy soils. Mulching - Perfect for leaf mulching. Optional Hydraulic Operated Transport Locks Transports locks can be released easily from the tractor seat while operating the same tractor control lever that raises and lowers the mower decks. Eliminates pulling a rope to release transport locks. 4/01/ F 6

10 and All Flex Mowers AFM4522 Model Counter rotation on left hand deck Spreads grass clippings more evenly. Wing decks throw grass away from the rear deck. Rear deck doesn t get covered up nor does it get bogged down by cut grass. Narrow 9'-6" transport width Transport width allows unit to be transported with ease. 4 1/2" Deck overlap Eliminates blade skips when turning. Tighter turns can be made. Sleek frame design, including single beam hitch and compact deck overlap Automatic transport wing locks P27560SR Transport tires with tapered bearings Removable transportation tire spindles Back wheels on side decks even with transportation tires Rigid rear side deck tires Large deck flotation tires with sealant Design allows operator to make tighter turns without leaving windrows and skips. The AFM virtually becomes a zero turn mower. When wings are raised in the full transport position, the wings lock in place. No need to get off the tractor to lock. Pull rope from tractor seat to un-lock. Large Transport tires offer smooth roading and less grass compaction. Allows grass to stand up. Tapered roller bearings offer longevity. Allows a spindle to be replaced by simply removing two bolts. Allows tighter turns without skips. Rigid wheel yokes holds hills and slopes better. Safer unit than the competition. Optional 15" tires for great flotation or 18" tires for even greater flotation. The larger the tire the less compaction in pounds per square inch allowing grass to stand up. Sealant in the tires minimizes flats. 1/4" Gauge wheel arms Gives the cutter gauge wheel arms a great deal of hidden strength. Low pivot points on deck The lower the pivot points are to the ground, the more side to side swing, allowing for excellent flotation from each deck. Deflectors built into mower decks Safety features meet ANSI standards. Many competitors use chains for protection. Once chains are removed the unit may not meet ANSI specifications. Rear discharge Even dispersal, discharged items are always aimed downward. No rear chains are needed, which tend to clump damp grass. Cat. 4 CV main driveline Constant velocity main driveline allows for tighter turns without harming U-joints in driveline. Cat. 3 slip-clutch wing drivelines Reduces start-up torque that is put on the driveline, gearbox and gearbox support. Slip clutch protection Guards against premature gearbox failure. Protects mower deck spindles. Heavy center gearbox mounting plate Handles start up torque. Gearbox HP Rating HP Gearbox warranty S/N one year on all gearbox components S/N years on gearbox housing, gears and shafts, 3 years on bearings and seals on gearbox. Easy to grease blade spindles No guards to remove for routine greasing of blade spindles. Middle spindle sits towards the back of the mower deck Spring loaded idlers Easy belt tension release High blade tip speed Choice of Blade (Medium lift standard) Others available thru parts dept. Optional Hydraulic Operated Transport Locks Uses less horsepower and allows material to escape the mower deck easier. The discharge of the material is more even. Design eliminates windrowing. Applies constant tension to belt to run efficiently. Easily release belt tension for changing belt or for winter storage. (18,498 fpm) Lifts the grass up for a clean cut and efficient discharge of material. Tip rates as high or higher than the competition. Low Lift - Highly recommended in sandy soils where lifting isn t crucial. Disturbs the soil very little, allowing blades to wear longer. Medium Lift - Medium suction for lifting grass. Requires less HP than high lift. High Lift - Greatest suction for lifting grass before cutting. Can take higher HP in tall dense grass. Not recommended in sandy soils. Mulching - Perfect for leaf mulching. Transports locks can be released easily from the tractor seat while operating the same tractor control lever that raises and lowers the mower decks. Eliminates pulling a rope to release transport locks. 4/01/ F 7

11 Angle Broom Table of Contents and Angle Broom Model AB84 32" Bristle Diameter Provides for long service life. Available in 60", 72" & 84" Working widths Choice of poly or wire or combination poly/wire bristles Faceted hood design Easily removable brush drive Choice of manual or hydraulic angling Brush angles 30 degrees to the left or right Compatible with 12GPM to 25GPM hydraulic flow at 2,000 psi Integral flow control valve Integral float control design Provides for excellent productivity and ideal sizes for most skid steers and compact utility tractors. Allows owner/operators to meet operational needs. Wire or poly/wire combinations provide more wear life and more aggressive sweeping action. Provides for a higher level of overall structural integrity. Allows for quick and easy change out of brushes without motor removal or opening hydraulic lines. Allows owner/operators to meet budgetary and operational needs. High or regular flow hydraulic options are offered to ensure that cylinder travel response is safe and appropriately matched to output flow of the tractor. Provides for excellent material control and puts sweepings where the operator wants them. Allows attachment to a wide range of skid steers and compatible compact utility tractors equipped with loader arms and skid steer adapter plates. Protects hydraulic system and motor from hydraulic inputs exceeding 25 GPM. Spring loaded adjustable down pressure control and stops prevent premature brush wear while providing appropriate surface contact with the rotary brush. 100 to 230 rpm brush rotation Provides for good sweeping action and material control. Integral storage stands Enables easy dismount and storage and keeps bristle ends from becoming deformed by supporting weight of the unit. Options Rubber Dust Deflector Flap Dust Suppression system Metal Shroud Extension Marker Indicators Helps keep dust levels under control and down and under the hood cowling and out of the operators field of vision. Hood mounted spray boom and nozzles dispense a fine spray mist in front of the broom to control and minimize airborne dust particles. Extends the broom shroud further forward to help control dust. Spray nozzles can be mounted on the extension to help minimize airborne dust particles. Aids operator in knowing exact position of extreme left and right edges of the unit for safer and unencumbered operation. 7/15/ F 8

12 Bale Spears Table of Contents and Bale Spears Designed to fit Skid Steer Loader hitches or Euro style hitches Bales can be pushed with single and double spear units Spear units punch holes in end of bale not in the circumference Single spear units also include two short bale spikes Single spear units takes less force to push the spear into the bale Double spear units have twice the lifting capacity Double spear units probe lower on the bale BS & BSE Series The BS Series can be attached to machines fitted with a Skid Steer adapter mounting plate and the BSE Series can be attached to machines fitted with a Euro style adapter mounting plate. Good for pushing bales onto side dump trailers. Very little moisture can enter the bale where spears punch. Grappling type bale lifts punch holes in the circumference allowing moisture to penetrate the bale and accelerates bale deterioration. Bale spikes keep bale from rotating on the single spear. Bales of all sizes won t shift positions as easily while pushing the spear into the bale. Single spears are ideal for lifting smaller lighter bales. Two spears can lift twice as much weight as a single spear. Also, the two spears spaced apart miss the soft inner core of a bale and probe the harder outer area allowing the spears to lift a heavier bale. They can lift the bale higher. 7/19/ F 9

13 Blades, Front and Table of Contents Blades, Front Reinforced 10 gauge moldboard design Choice of 96" or 108" working widths Double acting angling cylinder Trip edge design with adjustable springs Easy attaching mounting system Rotational free floating tilt action blade design Transport lock Standard operator mounting step TB2596 & TB25108 Models Provides added strength and durability. Allows customers to choose the blade that meets their operational needs. Easily enables up to 30 degrees of angling to left or right distributing the load where you want it to go. Protects the structural integrity of the blade while still maintaining load control no matter what the bottom edge encounters. Adapted for skid steer mounting and tractor loaders with skid steer type mounting plates. Allows blade to rotate on its mounting trunnion keeping the blade edge in uniform contact with the ground. Keeps blade level in transport for better operator visibility and safer handling. Provides for safer and easier mounting and dismounting by the operator when the blade is used in skid steer applications. 41" overall blade depth Provides ability to perform in deeper snow conditions. Replaceable bottom wear edge Skid Shoes Optional Blade Marker Optional Top Mounted Rubber Deflector Offered in steel or heavy duty poly construction to match ground & surface operating conditions. Offered as standard equipment. Establish lower limits of blade operation to prevent surface gouging or cutting to deep. Provides operator with improved awareness and visibility of outermost edges of the blade bottom to prevent unwanted contact with ground obstacles. Helps prevent snow from over-topping the moldboard in deeper snow conditions. 3/04/ F 10

14 Rear Table of Contents and Blades, Rear RB05 Series Warranty One year parts & labor. See warranty page for complete details. 48", 60" Working widths Choice of two sizes to pick from HP rating Fits a wide variety of small tractors between 17 & 25 HP. Cat. 0 with Cat. 1 pins and Fits smaller tractors with Cat. 0 hitch & Cat. l limited hitch. Cat. l limited hitch types Blade angles left and right up to 30 o in either direction Blade offsets left and right 10" (5 forward positions in 15 o increments and 5 reverse positions in 15 o increments) Many angles for diverse jobs and results. Manually adjust offset to move moldboard over and keep hitch centered on tractor. 13 1/2" Moldboard height Can pull a lot of dirt for a little blade. Heat treated cutting edge Hard edge protects the moldboard edge. Parking Stand Store unit with front of hitch off the ground, allows for easier hook-up. Landscape Rake adaptable 05 Series Landscape Rake element will fit in place of the moldboard for diversity. Skid shoes (optional) Set depth of blade to clear obstructions like manhole covers, street cracks. RB15 Series Warranty One year parts & labor. 60", 72", 84" Working widths Choice of three sizes to pick from HP rating Fits a wide variety of small tractors between 17 & 40 HP. Quick-Hitch Fits Land Pride Quick-Hitch. Blade angles left and right up to 45 o in forward position and 30 o in reverse position Blade offsets 12" left and right (7 Forward positions in 15 o increments and 5 reverse positions in 15 o increments) Many angles for diverse jobs and results. Manually move moldboard to cover either tractor tire. 14" High rolled moldboard Rolled moldboard allows material to flow easily, which means less drag, less HP. 1/4" moldboard thickness Is just right for 40 HP work. Reversible cutting edge For twice the life. Parking Stand Store unit with front of hitch off the ground, allows for easier hook-up. Skid shoes (optional) Set depth of blade to clear obstructions like manhole covers, street cracks. Landscape Rake adaptable Remove moldboard and add rake element to add diversity of frame. 2/24/ F 11

15 and Blades, Rear Warranty RB16 Working Widths (60", 72", 84") RB26 Working Widths (72", 84", 96") HP rating for RB16 Series HP for RB26 Series Quick Hitch Blade angles left and right up to 45 o in forward position and 30 o in reverse position Blade offsets left or right 12" Blade tilts up or down up to 15 o Formed rolled moldboard RB16 Series (14" High Moldboard) RB26 Series (17 1/2" High Moldboard) Reversible cutting edge Parking stand RB16 & RB26 Series One year parts & labor. See warranty page for complete details. Choice of three sizes per Series to pick from. RB16 Series fits a wide variety of small tractors between 20 & 40 HP. RB26 Series fits a wide variety of small tractors between 25 & 60 HP. Fits Land Pride Quick Hitch. (7 Forward positions in 15 o increments and 3 reverse positions in 30 o increments) Many angles for diverse jobs and results. Manually move moldboard to cover either tractor tire. (5 positions: Center, 2 clockwise, and 2 counterclockwise) Allows operator to do simple tasks such as putting a crown in the middle of a road to making V-type ditches. Rolled moldboard allows material to flow easily, which means less drag, less HP. 14" High moldboard for good capacity. 17 1/2" High moldboard for excellent capacity. For twice the life. Store unit with front of hitch off the ground, allows for easier hook-up. End Plates (Accessory) End plates hold material in to be moved. Skid shoes (Accessory) Help protect from hitting low obstructions by keeping the cutting edge off the ground. Set skid shoes to clear obstructions like manhole covers and street cracks. Rake Assembly (Accessory) The blade assembly can be removed from the main frame and a rake assembly attached to give the Land Pride Rear Blade versatility. Hydraulic Angling (Accessory) Makes rotating blade angle horizontally easy with infinite number of angles available between 0 o and 45 o clockwise and counterclockwise. 3/19/ F 12

16 and Blades, Rear RB37 Series Warranty One year parts & labor. See warranty page for complete details. Working widths (72", 84" & 96") Choice of three sizes to pick from HP rating Fits a wide variety of small tractors. Quick-Hitch Fits Land Pride Quick-Hitch. Blade angles left and right up to 45 o in forward position and 30 o in reverse position Blade offsets left or right up to 26" Blade tilts up or down up to 15 o Allows operator to set the blade at many angles to complete different jobs with satisfactory results. See Specifications for number of angles in forward and reverse positions. Manually rotate main frame in 15 o increments up to 45 o to cover either tractor tire and to allow operators to work next to retaining walls, abutments, and curbing. (5 positions: Center, 2 clockwise, and 2 counterclockwise) Allows operator to do simple tasks such as putting a crown in the middle of a road to making V-type ditches. 17" High moldboard Rolled moldboard allows material to flow easily, which means less drag, less HP. 17" High moldboard for excellent capacity. Reversible cutting edge For twice the life. Parking Stand Store unit with front of hitch off the ground, allows for easier hook-up. Hydraulic Angling (Accessory) Allows operator to change blade angle from the tractor seat. End Plates (accessory) End plates hold material in to be moved. Skid Shoes (accessory) Help protect from hitting low obstructions by keeping the cutting edge off the ground. Set skid shoes to clear obstructions like manhole covers and street cracks. 4/02/ F 13

17 and Blades, Rear RBT35 Series Warranty One year parts & labor. See warranty page for complete details. 84" & 96" Working widths Choice of two sizes to pick from. Both sizes handle large capacities. 35 to 80 HP range for 2-Wheel Drive Fits a wide variety of tractors. 35 to 65 HP range for 4- Wheel Drive Cat. 1 or 2 Fits wide variety of tractors. Fits Land Pride Quick-Hitch Quick and easy attaching without leaving tractor seat. 3-Way Blade Tilt, angle and offset features available hydraulically or manually. Blade angles left and right up to 40 o manually and up to 50 o hydraulically in either direction (9 positions manually: Center, 4 clockwise and 4 counterclockwise in 10 o increments) (Hydraulically: Any degree up to 50 degrees) Allows the operator to set the blade at the angle of his choice up to 40 o to complete the job with satisfactory results. Blade offsets left and right up to 30" (9 positions manually: Center, 4 positions left and 4 positions right) (Hydraulically: Any position up to 30") Allows the operator to position the end of the moldboard beyond tractor tire and close to solid obstacles such as fences, buildings and abutments. Blade tilts up and down up to 20 o Allows the operator to do simple tasks such as putting a crown in the middle of a road to making V-type ditches of various sizes. Fully welded main frame Fully welded adds overall strength and rigidity to blade frame. (Tubular construction) Heavy-duty pivot assembly with 3" solid steel kingpin Formed 17 inch Moldboard 5/16" Moldboard thickness with box reinforcement Reversible cutting edge Retractable parking stand 3/4" Plate steel turntable and 3" kingpin for handling the high amount of torque that can be transferred to this area. Precisely formed moldboard rolls dirt and debris with ease. Thick material with fully welded box reinforcement creates a strong moldboard. Get twice the wear from the cutting edge by flipping it over. Able to store the unit with the frame off the ground, also aids in attaching to tractor. Skid shoes End plates Cushion valve Accessories Skid shoes help protect from hitting low obstructions by keeping the moldboard off the ground. End plates hold material in and allows it to be moved. Helps protect the moldboard and cylinders in the event an obstruction is hit by allowing hydraulic fluid to bypass the cushion valve and flow back towards the tractor. 6/10/ F 14

18 and Blades, Rear RBT40 Series Warranty One year parts & labor. See warranty page for complete details. 84", 96", 108" Working widths Choice of three sizes to pick from. All sizes handle large capacities. 65 to 100 HP Rating Fits a wide variety of tractors. Cat. 1 or 2 Fits wide variety of tractors. Fits Land Pride Quick-Hitch Quick and easy attaching without leaving tractor seat. 3-Way Blade Tilt, angle and offset features available hydraulically or manually. Blade angles left and right up to 45 o in either direction (15 positions manually: Center, 7 clockwise and 7 counterclockwise) (Hydraulically: Any degree up to 45 degrees) Allows operator to set the blade at the angle of his choice up to 45 o to move the desired amount of material with satisfactory results. Blade offsets left and right up to 30" (15 positions manually: Center, 7 positions left and 7 positions right) (Hydraulically: Any position up to 30") Allows the operator to position the end of the moldboard beyond tractor tire and close to solid obstacles such as fences, buildings and abutments. Blade tilts up and down up to 15 o Allows the operator to do simple tasks such as putting a crown in the middle of a road to making V-type ditches of various sizes. Fully welded main frame Fully welded adds overall strength and rigidity to blade frame. Heavy-duty pivot assembly with 3 1/8" solid steel kingpin Formed 17 inch Moldboard 5/16" Moldboard thickness with box reinforcement Reversible cutting edge Retractable parking stand 3/4" Plate steel turntable and 3 1/8" kingpin for handling the high amount of torque that can be transferred to this area. Precisely formed moldboard rolls dirt and debris with ease. Thick material with fully welded box reinforcement creates a strong moldboard to handle tough jobs. Get twice the wear from the cutting edge by flipping it over. Able to store the unit with the frame off the ground, also aids in attaching to tractor. Skid shoes End plates Cushion valve Selector Valve Accessories Skid shoes help protect from hitting low obstructions by keeping the moldboard off the ground. End plates hold material in and allows it to be moved. Helps protect the moldboard and cylinders in the event an obstruction is hit by allowing hydraulic fluid to bypass the cushion valve and flow back towards the tractor. Provides a way to operate 2 cylinders at one outlet, thereby reducing the number of required outlets by one. 6/10/ F 15

19 and Blades, Rear RBT45 Series Warranty One year parts & labor. See warranty page for complete details. 96" & 108"Working widths Choice of two sizes to pick from. Both sizes handle large capacities HP Range Fits a wide variety of tractors. Cat. 2 and 3 Bushing provided to go from Cat. 2 to Cat. 3 enables a wider variety of tractors to be used. Quick hitch compatible Compatible with Land Pride Quick hitch for easy attachment and removal. Increases productivity. Blade angles left and right up to 45 o in either direction (15 positions manually: Center, 7 clockwise and 7 counterclockwise) (Hydraulically: Any degree up to 45 degrees) Allows operator to set the blade at the angle of his choice up to 45 o to move the desired amount of material with satisfactory results. Blade offsets left and right up to 35" (15 positions manually: Center, 7 positions left and 7 positions right) (Hydraulically: Any position up to 35") Allows the operator to position the end of the moldboard beyond tractor tire and close to solid obstacles such as fences, buildings and abutments. Blade tilts up and down up to 15 o Allows the operator to do simple tasks such as putting a crown in the middle of a road to making V-type ditches of various sizes. Fully welded reinforced main frame Overall mainframe strength is enhanced due to being fully welded. Heavy-duty pivot assembly with 4" solid steel kingpin Formed 19" moldboard with top lip reinforcement 5/16" Moldboard with 1/4" reinforcement Grease zerks at all pivot points Reversible cutting edge Retractable parking stand Skid shoes (optional) End plates (optional) Cylinder cushion valve (optional) Single or dual gauge wheels (optional) 1" Plate steel turntable and 4" kingpin for handling the high amount of torque that can be transferred to this area. Formed moldboard with 90 degree bent top for additional strength. Tall moldboard allows for a great deal of material to be moved. Heavy-duty moldboard to handle loads from 125 HP tractors. Helps front pivot shaft maintain bind free movement. Lengthens blade life by being able to turn cutting edge over and use other edge. Enables one person hook-up and keeps the mainframe off of the ground. Skid shoes protect moldboard from hitting low-lying obstructions such as manhole covers. End plates allow the blade to hold material in to drag from one spot to another. Cylinder cushion valve protects the cylinders and blade from sudden impacts by allowing hydraulic fluid to escape vs. blowing seals. Gauge wheels position the height of the blade to aid in grading. 6/10/ F 16

20 and Blades, Rear RBT55120 Model Warranty One year parts and labor. See warranty page for complete details. 120" Working width Can handle large capacities HP Range Fits a wide variety of tractors. Cat. 2 and 3 Bushing provided to go from Cat. 2 to Cat. 3 enables a wider variety of tractors to be used. Quick hitch compatible Compatible with Land Pride Quick hitch for easy attachment and removal. Increases productivity. Blade angles left or right up to 45 o in either direction Blade offsets left or right up to 33" Blade tilts up or down up to 15 o Fully welded reinforced main frame Heavy-duty pivot assembly with 4" solid steel kingpin Formed 19" moldboard with top lip reinforcement 5/16" Moldboard with 1/4" reinforcement Heavy-duty pivot assembly Grease points in front pivot shaft Reversible cutting edge Retractable parking stand Skid shoes (Optional) End plates (optional) Hardened wear edges (optional) Single or dual gauge wheels (optional) (15 positions manually: Center, 7 clockwise, and 7 counterclockwise) (Hydraulically: Any degree up to 45 degrees) Allows operator to set the blade at the angle of his choice up to 45 o to move the desired amount of material with satisfactory results. (15 positions manually: Center, 7 positions left, and 7 positions right) (Hydraulically: Any position up to 33") Allows the operator to position the end of the moldboard beyond tractor tire and close to solid obstacles such as fences, buildings, and abutments. Allows the operator to do simple tasks such as putting a crown in the middle of a road to making V-type ditches of various sizes. Overall mainframe strength is enhanced due to being fully welded. 1" Plate steel turntable and 4" kingpin for handling the high amount of torque that can be transferred to this area. Formed moldboard with 90 degree bent top for additional strength. Tall moldboard allows for a great deal of material to be moved. Heavy-duty moldboard to handle loads from 180 HP tractors. 1" Plate steel turntable and 4" kingpin handle tremendous torque delivered by up to 180 HP tractors. Helps front pivot shaft to easily move. Lengthens blade life by being able to turn cutting edge over and use other edge. Enables one person hook-up and keeps the mainframe off of the ground. Skid shoes protect moldboard from hitting low lying obstructions such as manhole covers. End plates allow the blade to hold material in to drag from one spot to another. Attach to outer edges of moldboard to prevent to wear in moldboard during ditching. Gauge wheels position the height of the blade to aid in grading. 3/19/ F 17

21 and Blades, Rear RBT60 Series Warranty One year parts and labor. See warranty page for complete details. 10 ft. & 12 ft. Working widths Choice of two sizes to pick from. Both sizes handle large capacities. High HP Range 2-Wheel Drive 4-Wheel Drive 225 Hp with 10 ft. blade & 175 HP with 12 ft. blade 200 Hp with 10 ft. blade & 160 HP with 12 ft. blade Cat. II and Cat III 3-Point Hitch Quick hitch compatible Blade angles left and right up to 45 degrees hydraulically Blade offsets left and right up to 55" hydraulically Blade tilts up and down up to 15 degrees hydraulically Mainframe is fully welded and reinforced Heavy-duty pivot assembly with 4 1/2" Diameter solid steel moldboard kingpin Formed 19" high moldboard 1/2" Formed Moldboard with 3/8" formed channel reinforcement Retractable parking stand Front pivot shaft has two grease points Heavy-duty blade pivot assembly Can go from Cat. II to Cat. III 3-point tractor. Enables a wider variety of tractors to be used. Compatible with Land Pride QH20 Cat. II Quick hitch for easy attachment and removal. Increases productivity. Allows the operator to set the blade at the angle of his choice to complete the job with satisfactory results. Allows the operator to position the end of the moldboard beyond tractor tire and close to solid obstacles such as fences, buildings and abutments. Allows the operator to do simple tasks such as putting a crown in the middle of a road to making V-type ditches of various sizes. Overall Mainframe strength is enhanced due to being fully welded. 1" Plate steel turntable and 4 1/2" King pin for handling high torque in this area up to 225 HP 2-wheel or 200 HP 4-wheel drive tractors with 10 ft. moldboard and 175 HP 2-wheel or 160 HP 4-wheel drive tractors with 12 ft. moldboard. Can move a great deal of material in a short time. Makes it one of the strongest moldboards in its class for handling heavy loads. Enables one person hook-up and keeps the mainframe off of the ground. Helps front pivot shaft to move easily. 1" Plate steel turntable and 4 1/2" kingpin handle tremendous torque delivered by up to 225 HP tractors. Skid shoes End plates Dual gauge wheels Accessories Skid shoes protect moldboard from hitting low lying obstructions such as manhole covers. End plates allow the blade to hold material in to drag from one spot to another. Gauge wheels position the height of the blade to aid in grading. 6/10/ F 18