product guide demand durability. select silent drive application charts

Transcription

1 2017 application charts product guide demand durability. select silent drive. Silent Drive Inc Arizona Place SW Orange City, Iowa Fax silentdrive.com Ph Page 1

2 what sets us apart? Patented Uro-flex Bushings Patented, free rotation design allows the inner sleeve to rotate. Because of this free rotational design, shear and torsional stress on the bushings are eliminated. Rubber bushings are bonded to both the outer and inner sleeve and when the arm rotates, the bushings material is twisted and contorted resulting in high stresses causing premature bushing failure. In addition, Urethane is a superior polymer which does not break down over time from exposure to petroleum products, acids, salts, or ozone that damage rubber. Urethane allows the suspension to flex in uneven terrain and cornering, yet it resists vehicle roll. High Pivot Point We engineer a higher pivot point into most of our pull arms to offer unmatched stability during cornering and while operating over uneven terrain. In addition, a high pivot point offers a drastic reduction in frame rail stress. In most cases, our pivot points are as much as 8 to 10 closer to the frame rail. Having the pivot point that close to the frame helps to eliminate most frame rail maintenance. Short Mounting Envelope Silent Drive offers some of the shortest mounting envelopes in the industry. Depending on the application, a Silent Drive suspension will often fit when other suspensions are too large. Under Arm Lift Most Silent Drive suspensions incorporate an Under Arm positive lift. In addition to quick lift response, an Under Arm lift offers superb driver comfort and reduced system maintenance. Huck Bolted Pivot Points Most Silent Drive suspensions incorporate Huck Bolted pull arm and axle seat bushings. Huck Bolting is recognized in the industry for its durability and lack of maintenance. Double Coil Spring Shocks All steerable Silent Drive suspensions incorporate double coil spring shocks for unsurpassed stability and driver control. Complete Mounting and Installation Kits Silent Drive has kits available for quick and easy installation. These kits include, but are not limited to, mounting hardware, air lines, valves, and brake fittings. Depending on the suspension, Silent Drive offers everything you need to do the complete installation. Totally Unitized Axle and Suspension Our suspensions and axles are totally unitized for reduced installation time. A unitized system includes a regulated inside-cab control panel, brake protection check valve, two quick release valves, standard brakes, wheels or hubs, drums, one lower cross member, and auto slack adjusters. Full Line Supplier Silent Drive offers a full line of air up / air down suspensions. In addition to the steerable and non-steerable pushers and tags, Silent Drive offers Parallelograms, Drive Axle, Primary Trailer and Liftable Trailer suspensions. Custom Suspension Design Silent Drive offers internal capabilities to design and manufacture custom suspensions to meet your needs. Silent Drive has the ability to adapt, modify or design around customer and market needs. Customer Service Silent Drive offers unsurpassed customer service. These services include nationwide distribution and 24-hour parts order turnaround. In addition, Silent Drive offers full-time technical help for customers and their end users.

3 table of contents SELF-STEER UNITS UF-1013-FA 13,200 lbs. Fabricated Axle; Pusher or Tag Axle 2 UF-1013-IB 13,200 lbs. I-Beam Axle; Pusher or Tag Axle 3 UF-1000 Configurations Inboard and Outboard 4 UF-2013-FA 13,200 lbs. Fabricated Axle; Pusher or Tag Axle 5 AAS-721-FA 13,200 lbs. Pusher or Tag Axle 6 AAS-721-FA Configurations Standard and Inboard 7 AAS-724-FA 20,000 lbs. Fabricated Axle; Pusher or Tag Axle 8 AAS-740-FA 13,000 lbs. Pusher Axle; Low Frame Truck 9 Pre-Plumb Kit 10 Air Controls and Kits 11 NON-STEER UNITS AA ,500 lbs. High Lift; Pusher or Tag Axle 12 AA ,500 lbs. High Lift; Tag Axle 13 AA-230-FA 13,200 lbs. Pusher or Tag Axle 14 AA-230 Configurations Inboard and Outboard 15 AA ,000 lbs. Low Frame; Pusher or Tag Axle 16 AA ,000 lbs. Pusher or Tag Axle 17 AA ,000 lbs. Pusher or Tag Axle 18 TRAILER SUSPENSIONS AA-270-TR 14,000 lbs. Pusher or Tag Axle 19 AA-290-TR 14,000 lbs. Pusher or Tag Axle 20 AA-1255-TR 20,000 lbs. Pusher or Tag Axle 21 ATR ,000 lbs. Primary Air Ride Suspension 22 MAXLE 12,000 lbs. Hydraulic Raised/Lowered Air Ride 23 CHARTS & GUIDES Federal Bridge Table 24 Air Pressure Load Chart 25 Loaded Tire Size Chart 26 ORDERING INFORMATION Truck 27 Trailer 28

4 UF-1013-FA Parallelogram Steer Lift Axle LOADED RIDE HEIGHT Frame Adjustment: Adjustable from frame width Application: Pusher(s) or Tag; Utilizes fabricated steer axle; Inboard and outboard configurations available (single tires); Short mounting envelope Suspension Capacity: 13,200 lbs. Axle Capacity: 13,200 lbs. Application Chart (to determine available lift): AVAILABLE LIFT 1.5" AXLE DROP Loaded Frame Height Ride Height: 11" - 16" Tire Radius (LOADED) (LOADED) (LOADED) " AXLE DROP Loaded Frame Height Ride Height: 9" - 14" Tire Radius (LOADED) (LOADED) (LOADED) " AXLE DROP Loaded Frame Height Ride Height: 7" - 12" Tire Radius (LOADED) (LOADED) (LOADED) When lifted, the top of the axle beam is 7 inches below the bottom of the frame. DO NOT install or operate suspension if parameters meet in a shaded box. To find the Loaded Tire Radius from a given tire size, refer to tire charts. Suspension capacity may be limited by tire capacity. IMPORTANT: If the suspension will be operated in the tag position, Silent Drive recommends not exceeding an axle spacing of 60 inches between the nearest drive axle and the lift axle. Contact Silent Drive before exceeding these limitations. Page 2 silentdrive.com

5 UF-1013-IB Parallelogram Steer Lift Axle Frame Adjustment: Adjustable from 33.5 to 34.5 frame width Application: Pusher(s) or Tag; Utilizes I-Beam steer axle; Inboard and outboard configurations available (single tires) Suspension Capacity: 13,200 lbs. Axle Capacity: 13,200 lbs LOADED RIDE HEIGHT Application Chart (to determine available lift): AVAILABLE LIFT 3.5" AXLE DROP Loaded Frame Height Ride Height: 9" - 12" Tire Radius (LOADED) (LOADED) (LOADED) " AXLE DROP Loaded Frame Height Ride Height: 7" - 10" Tire Radius (LOADED) (LOADED) (LOADED) When lifted, the top of the axle beam is 8 inches below the bottom of the frame. DO NOT install or operate suspension if parameters meet in a shaded box. To find the Loaded Tire Radius from a given tire size, refer to tire charts. Suspension capacity may be limited by tire capacity. IMPORTANT: If the suspension will be operated in the tag position, Silent Drive recommends not exceeding an axle spacing of 60 inches between the nearest drive axle and the lift axle. Contact Silent Drive before exceeding these limitations. CALL Page 3

6 Ultra Flex Series Configuration Options Inboard configuration for rolloffs and hoists with outboard cylinders Outboard configuration for hoists with inboard cylinders Page 4 silentdrive.com Page 6 silentdrive.com

7 UF-2013-FA Parallelogram Steer Lift Axle Frame Adjustment: Adjustable from 33.5 to 34.5 frame width Application: Pusher(s) or Tag; Utilizes fabricated steer axle; Inboard and outboard configurations available (single tires) Suspension Capacity: 13,200 lbs. Axle Capacity: 13,200 lbs LOADED RIDE HEIGHT Application Chart (to determine available lift): AVAILABLE LIFT 1.5" AXLE DROP Loaded Frame Height Ride Height: 13" - 18" Tire Radius (LOADED) (LOADED) (LOADED) " AXLE DROP Loaded Frame Height Ride Height: 11" - 16" Tire Radius (LOADED) (LOADED) (LOADED) " AXLE DROP Loaded Frame Height Ride Height: 9" - 14" Tire Radius (LOADED) (LOADED) (LOADED) When lifted, the top of the axle beam is 9.5 inches below the bottom of the frame. DO NOT install or operate suspension if parameters meet in a shaded box. To find the Loaded Tire Radius from a given tire size, refer to tire charts. Suspension capacity may be limited by tire capacity. IMPORTANT: If the suspension will be operated in the tag position, Silent Drive recommends not exceeding an axle spacing of 60 inches between the nearest drive axle and the lift axle. Contact Silent Drive before exceeding these limitations. CALL Page 5

8 AAS-721-FA Parallelogram Air Lift Air Suspension Application: Dual Pusher or Tag; Utilizes front steering axle (single tires) Suspension Capacity: 13,200 lbs. Axle Capacity: 13,200 lbs. Application Chart (to determine available lift): AVAILABLE LIFT 3.5" AXLE DROP Loaded Frame Height Ride Height: 11" - 13" Tire Radius (LOADED) (LOADED) (LOADED) (LOADED) LOADED RIDE HEIGHT 5.5" AXLE DROP Loaded Frame Height Ride Height: 9" - 11" Tire Radius (LOADED) (LOADED) (LOADED) (LOADED) When lifted, the top of the axle beam is 7.75 inches below the bottom of the frame. DO NOT install or operate suspension if parameters meet in a shaded box. To find the Loaded Tire Radius from a given tire size, refer to tire charts. Suspension capacity may be limited by tire capacity. IMPORTANT: If the suspension will be operated in the tag position, Silent Drive recommends not exceeding an axle spacing of 60 inches between the nearest drive axle and the lift axle. Contact Silent Drive before exceeding these limitations. Page 6 silentdrive.com

9 AAS-721-FA Configuration Options All Dimensions Reference Standard 34 Inch Frame Width Inboard configuration for rolloffs and hoists with outboard cylinders Outboard configuration for hoists with inboard cylinders. CALL Page 7

10 36.00 AAS-724-FA Parallelogram Air Lift Air Suspension Application: Pusher or Tag; Utilizes fabricated steering axle (single tires) Suspension Capacity: 20,000 lbs. Axle Capacity: 20,000 lbs LOADED RIDE HEIGHT Application Chart (to determine available lift): AVAILABLE LIFT 3.5" AXLE DROP Loaded Frame Height Ride Height: 8" - 12" Tire Radius (LOADED) (LOADED) (LOADED) (LOADED) When lifted, the top of the axle beam is 7.5 inches below the bottom of the frame. DO NOT install or operate suspension if parameters meet in a shaded box. To find the Loaded Tire Radius from a given tire size, refer to tire charts. Suspension capacity may be limited by tire capacity. IMPORTANT: If the suspension will be operated in the tag position, Silent Drive recommends not exceeding an axle spacing of 60 inches between the nearest drive axle and the lift axle. Contact Silent Drive before exceeding these limitations. Page 8 silentdrive.com

11 AAS-740-FA Parallelogram Air Lift Air Suspension 8.27 LOADED RIDE HEIGHT Application: Pusher or Tag; Utilizes front steering axle (single tires) Suspension Capacity: 13,000 lbs. Axle Capacity: 13,200 lbs. Application Chart (to determine available lift): AVAILABLE LIFT 3.5" AXLE DROP Loaded Frame Height Ride Height: 8" - 9" Tire Radius (LOADED) (LOADED) (LOADED) (LOADED) " AXLE DROP Loaded Frame Height Ride Height: 6" - 7" Tire Radius (LOADED) (LOADED) (LOADED) (LOADED) 5 6 When lifted, the top of the axle beam is 6 inches below the bottom of the frame. DO NOT install or operate suspension if parameters meet in a shaded box. To find the Loaded Tire Radius from a given tire size, refer to tire charts. Suspension capacity may be limited by tire capacity. IMPORTANT: If the suspension will be operated in the tag position, Silent Drive recommends not exceeding an axle spacing of 60 inches between the nearest drive axle and the lift axle. Contact Silent Drive before exceeding these limitations. CALL Page 9

12 PRE-PLUMB KIT includes: AT-100K Air Tank R-12 Valve Brake Protection Valve Two Quick Release Valves Brackets & Hoses Installed PagE 10 silentdrive.com

13 air controls SD-812 Inside cab control unit for non-steer air up/air down suspension systems. AC-2000 Outside cab regulator with in-cab switch for operation. Use for self-steer suspensions when auto-reverse is needed or for non-steer suspensions when outside regulator is required. FK-2000 SD-865 SD-866 SD-847 AT-100K SLD-UPP Mounting Kits Air lines and fittings for AC-2000 controller Air lines and fittings for SD-812 controller Mounting bolts and lock nuts Air lines and fittings with R-12 valve for brakes Air tank kit Pre-plumb kit CALL Page 11

14 24.00 AA-115 Air Lift Air Suspension LOADED RIDE HEIGHT Application: Pusher or Tag; Non-Steer; High frame or low profile tires Suspension Capacity: 13,500 lbs. Axle Capacity: 20,000 lbs. Application Chart (to determine available lift): AVAILABLE LIFT AVAILABLE LIFT Loaded Frame Height Ride Height: 9" - 14" Tire Radius (LOADED) (LOADED) (LOADED) (LOADED) (LOADED) (LOADED) (LOADED) When lifted, the top of the axle tube is 0.5 inches below the bottom of the frame. DO NOT install or operate suspension if parameters meet in a shaded box. To find the Loaded Tire Radius from a given tire size, refer to tire charts. Suspension capacity may be limited by tire capacity. IMPORTANT: If the suspension will be operated in the tag position, Silent Drive recommends not exceeding an axle spacing of 60 inches between the nearest drive axle and the lift axle. Contact Silent Drive before exceeding these limitations. Page 12 silentdrive.com

15 25.50 AA-135 Air Lift Air Suspension LOADED RIDE HEIGHT Application: Tag only; Non-Steer; High frame or low profile tires Suspension Capacity: 19,000 lbs. Axle Capacity: 20,000 lbs. Application Chart (to determine available lift): AVAILABLE LIFT AVAILABLE LIFT Loaded Frame Height Ride Height: 11" - 15" Tire Radius (LOADED) (LOADED) (LOADED) (LOADED) (LOADED) (LOADED) (LOADED) When lifted, the top of the axle tube is 1.5 inches below the bottom of the frame. DO NOT install or operate suspension if parameters meet in a shaded box. To find the Loaded Tire Radius from a given tire size, refer to tire charts. Suspension capacity may be limited by tire capacity. IMPORTANT: If the suspension will be operated in the tag position, Silent Drive recommends not exceeding an axle spacing of 60 inches between the nearest drive axle and the lift axle. Contact Silent Drive before exceeding these limitations. CALL Page 13

16 23.81 AA-230-FA Air Lift Air Suspension LOADED RIDE HEIGHT Application: Pusher or Tag; Utilizes fabricated Non-Steer axle Suspension Capacity: 13,000 lbs. Axle Capacity: 13,200 lbs. Application Chart (to determine available lift): AVAILABLE LIFT 1.5" AXLE DROP Loaded Frame Height Ride Height: 11" - 13" Tire Radius (LOADED) * 8* 18.0 (LOADED) * 8* 19.0 (LOADED) * 8* 20.0 (LOADED) * 8* 3.5" AXLE DROP Loaded Frame Height Ride Height: 9" - 11" Tire Radius (LOADED) * 8* 18.0 (LOADED) * 8* 19.0 (LOADED) * 8* 20.0 (LOADED) * 8* When lifted, the top of the axle beam is 6 inches below the bottom of the frame. * Suspension mounted down 2 inches (see installation instructions.) DO NOT install or operate suspension if parameters meet in a shaded box. To find the Loaded Tire Radius from a given tire size, refer to tire charts. Suspension capacity may be limited by tire capacity. IMPORTANT: If the suspension will be operated in the tag position, Silent Drive recommends not exceeding an axle spacing of 60 inches between the nearest drive axle and the lift axle. Contact Silent Drive before exceeding these limitations. Page 14 silentdrive.com

17 AA-230-FA Configuration Options All Dimensions Reference Standard 34 Inch Frame Width Inboard configuration for rolloffs and hoists with outboard cylinders Outboard configuration for hoists with inboard cylinders. CALL Page 15

18 AA-240 Air Lift Air Suspension 5.00 LOADED RIDE HEIGHT Application: Pusher; Non-Steering; Low or drop frames; Low profile tires Suspension Capacity: 10,000 lbs. Axle Capacity: 20,000 lbs. Application Chart (to determine available lift): AVAILABLE LIFT Loaded Frame Height Ride Height: 8" - 10" Tire Radius (LOADED) (LOADED) (LOADED) (LOADED) (LOADED) (LOADED) (LOADED) (LOADED) When lifted, the top of the axle tube is 0.5 inches below the bottom of the frame. DO NOT install or operate suspension if parameters meet in a shaded box. To find the Loaded Tire Radius from a given tire size, refer to tire charts. Suspension capacity may be limited by tire capacity. IMPORTANT: If the suspension will be operated in the tag position, Silent Drive recommends not exceeding an axle spacing of 60 inches between the nearest drive axle and the lift axle. Contact Silent Drive before exceeding these limitations. Page 16 silentdrive.com

19 38.00 AA-1355 Air Lift Air Suspension LOADED RIDE HEIGHT Application: Pusher or Tag; Non-Steerable; Provides maximum roll stability Suspension Capacity: 20,000 lbs. Axle Capacity: 20,000 lbs. Application Chart (to determine available lift): AVAILABLE LIFT Loaded Frame Height Ride Height: 11" - 13" Tire Radius (LOADED) * 7* 16.0 (LOADED) * 7* 17.0 (LOADED) * 7* 18.0 (LOADED) * 7* 19.0 (LOADED) * 7* 20.0 (LOADED) * 7* 21.0 (LOADED) * 7* When lifted, the top of the axle tube is 3.5 inches below the bottom of the frame. * Suspension mounted down 2 inches (see installation instructions) DO NOT install or operate suspension if parameters meet in a shaded box. To find the Loaded Tire Radius from a given tire size, refer to tire charts. Suspension capacity may be limited by tire capacity. IMPORTANT: If the suspension will be operated in the tag position, Silent Drive recommends not exceeding an axle spacing of 60 inches between the nearest drive axle and the lift axle. Contact Silent Drive before exceeding these limitations. CALL Page 17

20 AA-1455 Air Lift Air Suspension Application: Pusher or Tag; Non-Steerable; Provides maximum roll stability Suspension Capacity: 20,000 lbs. Axle Capacity: 20,000 lbs. Application Chart (to determine available lift): AVAILABLE LIFT Loaded Frame Height Ride Height: 8" - 10" Tire Radius (LOADED) * 6* 16.0 (LOADED) * 6* 17.0 (LOADED) * 6* 18.0 (LOADED) * 6* 19.0 (LOADED) * 6* 20.0 (LOADED) * 6* 21.0 (LOADED) * 6* When lifted, the top of the axle tube is 1.5 inches below the bottom of the frame. * Suspension mounted down 2 inches (see installation instructions) LOADED RIDE HEIGHT 9.68 DO NOT install or operate suspension if parameters meet in a shaded box. To find the Loaded Tire Radius from a given tire size, refer to tire charts. Suspension capacity may be limited by tire capacity. IMPORTANT: If the suspension will be operated in the tag position, Silent Drive recommends not exceeding an axle spacing of 60 inches between the nearest drive axle and the lift axle. Contact Silent Drive before exceeding these limitations. Page 18 silentdrive.com

21 LOADED RIDE HEIGHT AA-270-TR Air Lift Air Suspension Application: Trailer; Non-Steering; High frame or low profile tires where space is limited Suspension Capacity: 14,000 lbs. Axle Capacity: 20,000 lbs. Application Chart (to determine available lift): AVAILABLE LIFT Loaded Frame Height Ride Height: 14" - 17" Tire Radius (LOADED) (LOADED) (LOADED) (LOADED) (LOADED) (LOADED) (LOADED) When lifted, the top of the axle tube is 6.5 inches below the bottom of the frame DO NOT install or operate suspension if parameters meet in a shaded box. To find the Loaded Tire Radius from a given tire size, refer to tire charts. Suspension capacity may be limited by tire capacity. IMPORTANT: If the suspension will be operated in the tag position, Silent Drive recommends not exceeding an axle spacing of 60 inches between the nearest drive axle and the lift axle. Contact Silent Drive before exceeding these limitations. CALL Page 19

22 LOADED RIDE HEIGHT AA-290-TR Air Lift Air Suspension Application: Trailer; Non-Steering; High frame or low profile tires where space is limited Suspension Capacity: 14,000 lbs. Axle Capacity: 20,000 lbs. Application Chart (to determine available lift): AVAILABLE LIFT Loaded Frame Height Ride Height: 17" - 20" Tire Radius (LOADED) (LOADED) (LOADED) (LOADED) (LOADED) (LOADED) (LOADED) When lifted, the top of the axle tube is 9.5 inches below the bottom of the frame DO NOT install or operate suspension if parameters meet in a shaded box. To find the Loaded Tire Radius from a given tire size, refer to tire charts. Suspension capacity may be limited by tire capacity. IMPORTANT: If the suspension will be operated in the tag position, Silent Drive recommends not exceeding an axle spacing of 60 inches between the nearest drive axle and the lift axle. Contact Silent Drive before exceeding these limitations. Page 20 silentdrive.com

23 38.50 AA-1255-TR Air Lift Air Suspension Application: Trailer; Non-Steerable; Provides maximum roll stability Suspension Capacity: 20,000 lbs. and 25,000 lbs. Axle Capacity: 20,000 lbs LOADED RIDE HEIGHT Application Chart (to determine available lift): AVAILABLE LIFT Loaded Frame Height Ride Height: 18" - 20"** Tire Radius (LOADED) * 6* 16.0 (LOADED) * 6* 17.0 (LOADED) * 6* 18.0 (LOADED) * 6* 19.0 (LOADED) * 6* 20.0 (LOADED) * 6* 21.0 (LOADED) * 6* When lifted, the top of the axle tube is 11 inches below the bottom of the frame. * Suspension mounted down 2 inches (see installation instructions) **Also available in other ride heights. DO NOT install or operate suspension if parameters meet in a shaded box. To find the Loaded Tire Radius from a given tire size, refer to tire charts. Suspension capacity may be limited by tire capacity. IMPORTANT: If the suspension will be operated in the tag position, Silent Drive recommends not exceeding an axle spacing of 60 inches between the nearest drive axle and the lift axle. Contact Silent Drive before exceeding these limitations. CALL Page 21

24 ATR-416 Primary Trailer Air Suspension features Air ride: Provides a smooth ride and maximum cargo protection. ride heights: 4 to 22 Suspension Capacity: 25,000 lbs. Axle: 71.5 to 77.5 Track Straight Non-Steer Axle Travel: 6 minimum Options Air Disk Brakes: Ride heights up to 20 Yoke Mounts Low Maintenance Durable UroFlex urethane bushings at main pivot point; No lubrication required; No bushings at axle. ATR-416 WITH lift Page 22 silentdrive.com

25 MAXLE Creates more revenue for users by increasing the outer bridge of the truck; up to 12,000 lbs. of additional payload per trip. By MAXLE-izing the outer bridge of your dump trucks, your customer s productive payload is increased, resulting in increased revenue for you. The MAXLE s unique adaptation (patent pending) of an extended arm in conjuction with Silent Drive s proven air suspension systems offers a smoother ride, unlike high maintenance hydraulic systems. You also get total modular unitized construction for reduced installation time and cost. Allows 100% utilization of dump body with zero restrictions to tailgate or dump angle, while adding increased lateral loading and improved stability for total driver comfort and confidence. features Air ride: Air ride suspension creates a smooth and controlled ride. AxLE track: The wide track axle allows controlled stability and visibility for the driver. Operation: Operates via the dump truck body PTO. Maintenance: Guaranteed low maintenance. MAXLE-DB Does not impede loading or dumping application while stowed in up position. Raises and lowers with standard PTO. Engineered and tested by industry leaders. Extends the bridge of the truck to MAXLE-ize payload and profit. Air ride suspension and a standard track steer axle offer a great ride and maximum stability. MAXLE-cm Raises to provide discharge of load. Raises and lowers with standard PTO. Engineered by industry professionals. Extends the bridge to MAXLE-ize profits. Air ride suspension for greater stability and softer ride. Steering axle for easy maneuverability. CALL Page 23

26 Federal bridge table Permissible Gross Loads For Vehicles In Regular Operation Based On Weight Formula W=500 (LN/N N + 36) Modified 1 Distance In Feet Between Any Group Of Two Or Maximum Gross Load Weight in Pounds Carried On Any Group Of 2 Or More Consecutive Axles 2 More Axles 1 2 AXLES 3 AXLES 4 AXLES 5 AXLES 6 AXLES 7 AXLES 8 34,000 34,000 > 8 38,000 42, ,000 42, ,000 43, , ,000 50, ,000 50, ,500 51, ,000 52, ,000 52,500 58, ,500 53,500 58, ,500 54,000 59, ,500 54,500 60, ,000 55,500 60,500 66, ,500 56,000 61,000 66, ,500 56,500 61,500 67, ,000 57,500 62,500 68, ,000 58,000 63,000 68,500 74, ,500 58,500 63,500 69,000 74, ,500 59,500 64,000 69,500 75, ,000 60,000 65,000 70,000 75, ,000 60,500 65,500 71,000 76, ,500 61,500 66,000 71,500 77, ,500 62,000 66,500 72,000 77, ,000 62,500 67,500 72,500 78, ,000 63,500 68,000 73,000 78, ,000 68,500 74,000 79, ,500 69,000 74,500 80, ,500 70,000 75, ,000 70,500 75, Exception 66,500 71,000 76, ,500 71,500 77, ,000 72,500 77, ,500 73,000 78, ,500 73,500 78, ,000 74,000 79, ,500 75,000 80, ,500 75, ,000 76, ,500 76, ,500 77, ,000 78, ,500 78, ,500 79, ,000 80, , , , , , Interstate 80, Gross Weight Limit Permissible loads are computed to the nearest 500 pounds. The modification consists in limiting the maximum load on any single axle to 20,000 pounds. 2 The following loaded vehicles must not operate over H15-44 bridges: 3-52 (5 axles) with wheelbase less than 38 feet; (5 axles) with wheelbase less than 45 feet; 3-3 (6 axle) with wheelbase less than 45 feet; and 7-, 8-, and 9-axle vehicles regardless of wheelbase. Page 24 silentdrive.com

27 Air Pressure Load Chart For use in determining the approximate air pressure required in the air springs to obtain a specific load on the axle. Load At Ground AA AA AA AAS- 724 UF UF AA- 115 AA- 740 AA- 135 AAS- 721 AAS- 727 AA- 230 AA- 270 AA ,000 lbs ,000 lbs ,000 lbs ,000 lbs ,000 lbs AA ,000 lbs ,000 lbs ,000 lbs ,000 lbs ,000 lbs ,000 lbs ,000 lbs ,000 lbs ,000 lbs ,000 lbs ,000 lbs. 100 Air Pressure (psi) The values given above are based on the ride height at the middle of the ride height range. The actual figures may vary depending on the actual suspension mounting height. The values given above are also based on an estimated weight of the axles, wheels, and tires of 1,200 lbs. Air pressure required will vary based on the axle, wheels, and tires used. To obtain an accurate air pressure reading for a specific load, the suspension must be calibrated on a load scale. Silent drive assumes no responsibility as to the accuracy of the weight of loads based on the above chart. CALL Page 25

28 Loaded Tire Size Chart For use in calculating the mounting height of Silent Drive air suspensions. Tube Type Tubeless ISO (Metric) Loaded Tire Radius 7.5R15 215/75R R R15 9R /70R R17.5 *245/70R *265/70R19.5 *285/70R R R20 8R R20 9R R20 10R R20 11R /70R /75R /80R /75R /80R /75R /80R /80R /80R /65R /75T /80R R20 12R R R22 13R R /65R R22 12R /65R R22 13R * For use only on hub & drum steer axle. Requires special hub piloted wheel, 20 uni-mount drum, and 15 brakes. These tires will not work with 16.5 brakes. Check ground clearance before using these smaller tires. Page 26 silentdrive.com

29 Information Needed To Order Liftable Air Suspensions For Installation On TRUCKS The following information is required for ordering Liftable Air Suspensions for installation on trucks or tractors. Obtaining as much of this information as possible in advance will speed the ordering and manufacturing process. Application: Pusher Tag 2nd Axle 3rd Axle 4th Axle For Stock Axle Spacing: from nearest drive axle to liftable axle Required Capacity: Frame Width: Frame Height: Tire Size: Indicate on the drawing below. Include any frame reinforcement and/or gloving. Indicate on the drawing below, both loaded and unloaded frame heights. Indicate on the drawing below the size of the tire to be used on the liftable axle; also indicate the loaded tire radius if known. Driveshaft Location (PUSHER ONLY): Indicate on the drawing below the distance from the bottom of the frame to the bottom of the driveshaft in the lowest position, at the location of the liftable axle. Hubs & Drums: Cast Spoke Hub Piloted Ten Hole Disc Short Stud Budd (stud piloted) Long Stud Air Brakes Self-Steering Special Requirements: Ready To Order? Call CALL Page 27

30 Information Needed To Order Liftable Air Suspensions For Installation On TRAILERS The following information is required for ordering Liftable Air Suspensions for installation on trailers. Obtaining as much of this information as possible in advance will speed the ordering and manufacturing process. Application: Pusher Tag 2nd Axle 3rd Axle 4th Axle For Stock Axle Spacing: from nearest drive axle to liftable axle Required Capacity: Frame Width: Frame Height: Tire Size: Indicate on the drawing below. Include any frame reinforcement and/or gloving. Indicate on the drawing below, both loaded and unloaded frame heights. Indicate on the drawing below the size of the tire to be used on the liftable axle; also indicate the loaded tire radius if known. Hubs & Drums: Cast Spoke Hub Piloted Ten Hole Disc Short Stud Budd (stud piloted) Long Stud Air Brakes Self-Steering Special Requirements: Ready To Order? Call Page 28 silentdrive.com

31 Suspension Modules Save Time & Money Great for OEMs and Refabs! Any Combination: Pre-Plumbed Pre-Wired

32 We Can Fit Your Application! Dump Trucks Super Dumps Fuel Trucks Road Tractors Feed Trucks Crane Trucks Grain Trucks Cement Mixers Block & Tile Trucks Delivery Trucks Garbage Trucks In the early 50s tag axles were gaining in popularity, but it soon became apparent that they lacked in traction. In an effort to address this problem, a company was started in 1953 in Sioux City, Iowa, producing large pulleys to be installed between the dual tires of the drive axle and tag axle. By connecting these pulleys with a large V-belt, the drive axle powered the tag axle. Since the tag axle was powered by silent V-belts instead of noisy gears, the company was called Silent Drive. By the early 70s, Silent Drive s suspension lifts were edging out V-belt drives in the marketplace, creating an opportunity to expand product lines, and soon required more space in the factory. In 1974, a new plant was built in Orange City, Iowa, and all operations were moved to this new location. Since that time, Silent Drive has been the innovative leader in the suspension industry. We were the first to use automatic leaf spring-lifts in the suspension. Additionally, the professionals at Silent Drive pioneered the concept of unitizing the suspension to an axle for a complete, ready-to-install system. The underarm air spring lift concept was developed by the Silent Drive engineering team, and has been adopted by nearly every suspension manufacturer in the nation. Silent Drive has grown from a regional manufacturer, supplying products primarily for the agricultural market, to an industry leader, manufacturing air suspensions for liftable tags and pushers, drive axle suspensions, as well as primary and auxiliary lift axles on trailers. Using state of the art technology like Pro-E and Finite Element Analysis for design and testing also allows us to provide custom built systems tailored to specific needs or applications. Expect the most complete product line, capacities from 10,000 to 30,000 pounds, axle lifts from 6 to 18 inches, patented Uroflex pull arm bushings, and excellent customer service from the industry leader. Our reputation for a quality product at a fair price has carried our business across the United States and into Canada. Our experience, adaptability, innovative leadership, and commitment to quality keeps us a step ahead of the competition. Page 32 silentdrive.com