Mini Pure. User Manual. Model Number:

Transcription

1 User Manual Rev Sailing Toward a Greener and Safer Tomorrow Mini Pure A Revolutionary system used to produce a limited supply of both a cleaner & a sanitizer from just salt, water, and electricity. It is not only a greener solution to cleaning it is 100% NON-TOXIC. Model Number: PN: VPM-SB (115VAC/230VAC) 1 P a g e

2 Contents Warnings Diagrams Unit Diagram Inside Unit Diagram Cell Diagram Installation & Set Up of Your Unit Pre-installation Water Test Diagram Connecting the VPM-SB User Information Smart Button Instructions Adding Salt Solution/Label Information Warranty Information Trouble Shooting Guide User Reference Guide Other Products By Viking Pure P a g e

3 Warnings The following warnings include general safety information for this equipment with detailed descriptions. ELECTRIC SHOCK HAZARD WARNING WARNING Improper grounding, setup, or usage of the system can cause electric shock and death. Turn off and disconnect power cord before servicing equipment. Use only grounded electrical outlets. Use only 3-wire extension cords. LIMITED PRODUCTION NOTICE Unit is intended to be used for smaller applications only. Unit is limited to use in the following ways: Unit shall not run, continuously, for more than 1 hour (6 runs) or unit may become damaged and/or cause injury. Unit shall not run for more than 3 hours (18 runs) per 24 hour period or unit may become damaged And/or cause injury. *Please See Warranty (Page 14) For Full Warranty Information*. EQUIPMENT MISUSE HAZARD Misuse can cause death or serious injury. Misuse of equipment will damage unit, void warranty (if new), or cause serious injury, even death. Check equipment daily. Repair or replace worn or damaged parts immediately. Do not alter or modify equipment. For use only by trained staff. Use equipment only for its intended purpose. Call your Viking Pure 1000 distributor for information. Route hoses and cables away from traffic areas, sharp edges, moving parts, and hot surfaces. Do not use hoses to pull equipment. Only use Viking accessories for this unit. Any other accessories may damage unit & void warranty Only Use Viking Pure Salt Use of any other types of salt will damage unit s membranes, chemically change the solutions, and may even cause physical harm. If you have any questions or comments regarding the warning information above please contact us at: Info@vikingpure.com Or 1-(386) USA 3 P a g e

4 1 Unit Diagram 3 VPM-SB Mini Pure 10 2 Key 1. Power Entry Module/Power Switch- This is where you plug in your power cord and turn the unit ON/OFF as well as the fuse for the system. 2. Salt Tube Cap/Salt Input 3. Smart Button- Used to Setup and Start Production (See pages for instructions) Salt Tube Level Window- Used to determine when you need to add another salt cartridge. 5. Filtered Water Inlet (On lower right side of unit) 6. Salt Tube Drain- To be used when refilling salt (See page 13 for more details) 7. Safe-T-Clean Outlet- This is where the Safe-T-Clean (NaOH) solution exits the cell into a container 8. Safe-T-San Outlet- This is where the Safe-T-San (HOCl) solution exits the cell into a container. 9. Door Latch- Latched with a phillips head screw 10. Control Lock- Lock comes with 2 keys 6 4 P a g e

5 17 Inside Unit Diagram VPM-SB Viking Pure: Mini Pure 11 Key 11. Salt Tube- This is where you will fill your salt tube. 12. Electrolyzer Cell- This is where both HOCl and NaOH solutions are produced. 13. Safe-T-San Flow Control- This should be adjusted only under the direction of a Viking Pure representative 14. Safe-T-Clean Flow Control- This should be adjusted only under the direction of a Viking Pure representative 15. Safe-T-San Outlet- This is where the Safe-T-San (HOCl) solution exits the cell into a container Safe-T-Clean Outlet- This is where the Safe-T- Clean (NaOH) solution exits the cell into a container. 17. Electrical Compartment- Turn off and Remove power cord prior to opening control door. (KEEP AREA DRY) 5 P a g e

6 18 Cell Diagram VPM-SB Viking Pure: Mini Pure 20 Key 18. Mounting Bracket 19. Safe-T-San Flow Control- This should be adjusted only under the direction of a Viking Pure representative 20. Red Tubes- Denotes all tubing used to transport HOCl Safe-T-Clean Flow Control- This should be adjusted only under the direction of a Viking Pure representative 22. Blue Tubes- Denotes all tubing used to transport NaOH. 23. Salt Brine Inlet- This is where the salt brine from the salt tube enters the cell. 24. Salt Brine Outlet- This is where the salt brine, that was not used, is recycled back to the salt tube. 25. Yellow Tubes- Denotes all tubing used to transport salt brine from the salt tube to the Electrolyzer Cell P a g e

7 Setting Up Your Control Pre-Installation Hard Water Test 1. Before installing your system you should do a quick Hard Water Test. 2. This test can be done by bringing a sample of your water (fresh out of the tap) to a local water testing facility or you may purchase a water testing kit from Viking Pure. 3. The different levels you will be testing for are as follows: a. Degrees Hardness: This test should result in NO MORE than 5 dh. b. Parts per Million: This test should result in NO MORE than 100 PPM. c. Grains per Gallon: This test should result in NO MORE than 5 gpg. d. Milligrams per Liter: This test should result in NO MORE than 90 Mg/L 4. The test must be performed to determine if a water softener is needed to run the system properly. 5. If a water softener is needed, shown by failed testing, one must be installed or warranty will be void (See page 10 for all warranty information). This is due to the fact that hard water will damage the membranes in the cell and drastically affect the lifespan of the unit. 7 P a g e

8 Setting up your Control: Diagram Water Filter (Included) Water Softener (Not Included) Water Source Salt Tube Draining (See Adding Salt on page 11 for more information) 8 P a g e

9 Connecting your Mini Pure 1. After removing the unit from the shipping container, inspect the unit for any marks and/or damage that may have resulted from mishandling during freight. If the unit is damaged report it to UPS or the shipping company involved. 2. Install unit in the best area, as determined by Pre-Install Site Evaluation Sheet (filled out and sent to Viking Pure, Distributor or Sales Representative before purchase of unit). Power connection is a standard wall outlet with ground, 3 prongs. FOR 115VAC AND 230VAC UNITS, USE PROPER OUTLET. 3. Water connection can be made with the fitting supplied or any other means that has a shutoff valve. The connection should accommodate the ¼ plastic supply line supplied. 4. Mount the water filter using the bracket supplied. The filter comes with a fitting installed on the Outlet end. Water supply should be connected to the inlet on filter. 5. Route the tubing from the water filter to the Mini Pure in such a way as to protect the tubing from damage and cut to size. Then install the tube into the Mini Pure lower right side as indicated, FILTERED WATER INLET (Item #5 on Pg. 4 of Manual). 6. Turn water on and check for any leaks at the water supply or on the water filter, if leaks occur: turn off water supply and check connection of all fittings to tubes and ensure they are pressed in firmly as shipment may have loosened some connections. 7. Add salt to the unit (see pg. 13 for Adding Salt to Unit) 8. Plug unit into a standard house hold type receptacle that is grounded to code (Item #9 on Pg. 4 of Manual). FOR 115VAC AND 230VAC UNITS, USE PROPER OUTLET. 9 P a g e

10 9. Turn system ON by activating power switch on upper left side of unit. (Item #1 on Pg. 4 of Manual). 10. Insert the One Gallon Containers (Provided) under their respective tubes, Red for Safe-T-San and Blue for Safe-T-Clean, into the lower section 11. Activate Smart Button (Item #3 on Pg. 4 of Manual) to full and run 1 full run to allow the air to purge out of all the lines then dispose of these solutions. (See page in Manual for Smart Button Instructions). 12. Replace the containers and reactivate the Smart Button (Item #3 on Pg. 4 of Manual), watching the first cycle to insure the proper fill of the bottles. The bottles should fill to the base of the handle. 13. If the fill is too high or too low please call Viking Pure, your distributor or your sales representative and they will assist you on adjusting the fill volume. 14. If adjustment was necessary, please reactivate Smart Button for another full run to ensure fill is now correct. 15. Place cap (provided) on the Safe-T-San One Gallon Container to retain the strength of the solution. When required amount of product is obtained, turn the power off and it will be ready for the next cycle when required just turn the power on and start Sailing with us Toward a Greener and Safer Tomorrow. 10 P a g e

11 Smart Button Instructions 1. When unit is first powered up (activated by Item # 1 on Pg. 4 of Manual), screen on Smart Button will display the Startup Screen featuring the Viking Pure logo for a few seconds. 2. The next screen, Dashboard Screen, will show the Model Number, Program Version Number and the Preset Run Time 3. Unit run time will be preset to fill the 1 Gallon Containers (included). If you require more or less fill solution output, for containers of varying sizes, you will need to adjust the run time. 4. To adjust the time, hold the Smart Button for approx. 3 seconds until the screen switches to a Minute Adjustment Screen. Once the Minute Adjustment Screen appears, tap the screen to change the time in minute increments. If adjustment is not made quickly enough, screen will change to Second Adjustment Screen. (Image to right shows the minutes being set at 11 minutes). 5. Once you are done with the Minute Adjustment Screen, do not press Smart Button for a few seconds and screen will switch to the Second Adjustment Screen. This screen will operate in the same manner as the Minute Adjustment Screen with the only difference that you will be adjusting the seconds in 10 second increments. If adjustment is not made quickly enough, screen will revert back to the Dashboard Screen. (Image to right shows the seconds being set at 20 seconds). 11 P a g e

12 6. When you are ready to begin producing solution, press and release Smart Button from the Dashboard Screen. Doing this will then bring you to the Ready Screen. This screen will display the total hours the unit has been in operation. This number will be used when determining Warranty (See page 14 of Manual for more Warranty information). (Image to the right shows that this unit has been in operation, ie. Only making solution, for 1 hour and 40 minutes) 7. To start normal operation and begin producing solutions, press the Smart Button one more time, from Ready Screen, and unit will start production for the set time. As system is in production, you will see an indication that the system is on (SYS ON) and a countdown timer displayed. This will show you how much time is left on your cycle. Once countdown reaches zero, your unit will stop production and will revert back to the Dashboard Screen. If you need to stop production in the middle of the cycle, you can press the Smart Button once and release. Please Note: Stopping production during a cycle does not PAUSE the production. It reverts the screen back to the Dashboard Screen and when you start production again, you will be starting from the full production time. To prevent spillage, empty 1 gallon jugs completely before running a new cycle. 12 P a g e

13 Adding Salt 1. Loosen salt tube cap (Item #2 on Pg. 4 of Manual). 2. Open salt tube drain valve (Item #6 on Pg.4 of Manual) at base of control and allow liquid to drain into a container (Do not dispose of this liquid, it is used in later steps). 3. When liquid stops draining close manual valve (Liquid will stop draining on its own at the correct level). 4. Fully remove salt tube cap (Item #2 on Pg. 4 of manual) 5. Begin filling salt tube with salt, stopping when approximately ¼ of space is still visible through clear salt tube. 6. Fill with the liquid drained (From step 2) to ½" from the top of the tube. 7. Ensure the outer surface of the tube is free from salt. 8. Replace the salt tube cap, but only until you feel it starts to get tight then stop. 13 P a g e

14 Solution/Label Information Safe-T-San - Product Name: Safe-T-San Product Purpose: Sanitizing/Disninfecting Active Ingredient: Hypochlorous Acid (HOCl) HOCl EPA CAS# Product Labels: Safe-T-Clean - Product Name: Safe-T-Clean Product Purpose: Cleaning/Degreasing Active Ingredient: Sodium Hydroxide (NaOH) HOCl EPA CAS# Product Labels: 14 P a g e

15 Warranty Warranty Viking Industries, Incorporated (Viking Pure) warrants that products manufactured by it shall be free of defects in material and workmanship when operated in accordance with Viking s operating and maintenance procedures for the following period from the date of shipment: Product Viking Pure: Mini Pure Warranty Limit 1 Year or 1000 Hours (Whichever occurs first) Viking s liability is limited to the repair or replacement, at Viking s option, of any product, which proves to be defective during the warranty period outlined. The product must be returned, prepaid by purchaser, to Viking after obtaining a Return Authorization Number from Viking. Viking shall have the right of final determination as to the existence and cause of any defects. This warranty shall not cover unauthorized repairs, alterations, modifications, or use by the purchaser of product for which it is not intended without prior written consent from Viking. This warranty shall not cover abuse, neglect, improper operating or maintenance procedures, voluntary or involuntary damages of the product by the purchaser. Unit shall not be run, continuously, for more than 1 hour (6 runs) or unit may become damaged and/or injury may occur. Unit shall not be run more than 3 hours (18 runs) in a 24 hour period or unit may become damaged and/or injury may occur. Viking s liability under this warranty shall in no event exceed the purchase order price and shall not cover any losses caused by delays or for any expenses for labor, supplies, machine rental or loss or damages to other property. No warranty is made with respect to customer equipment or products manufactured to purchaser s specifications except as specifically stated in writing by Viking. Warranty will be void if salt other than that supplied by Viking Pure is used. Warranty will be void if : a) Hard Water Test is not performed b)hard Water Test is performed, failed to meet Viking s set limits (as defined on page 6) and no water softener is installed. Viking s responsibility for transportation under this warranty is limited to charges for delivery of repaired products via the least expensive transportation available, to the purchaser in the Continental United States only. Payment for shipment of Viking parts or products to Viking s facilities is the responsibility of the purchaser. Warranty for items that are repaired or replaced by Viking shall continue in effect for the remainder of the original warranty period or for ninety (90) days following the date of shipment by Viking, whichever period is longer. This warranty supersedes any other warranty, expressed or implied, and constitutes all of Viking Industries, Inc. s liability with respect to its products. 15 P a g e

16 Trouble Shooting Guide 1. My unit won t turn on Check to make sure power cord (supplied) is plugged into unit and also into wall outlet then turn switch on (See #1 on Page 4). If both ends of power cord are plugged in and flipping switch does nothing, you should check your power outlet. If you are comfortable with electricity and have an Electrical Meter available, check to make sure your power outlet is working properly by checking it for correct Voltage (115/230VAC). If you are not comfortable with or knowledgeable of working with electricity, contact your electrician to complete this step. If you are unable to start up your Mini Pure after trying the two steps above, contact your Distributor, Representative or Viking Pure. Quick Contact Info: ( ) - 2. Unit runs for a few seconds and then shuts off Check to ensure that your source water is turned on. If water does not flow to unit, unit will shut off to protect itself. Ensure there is salt in salt tube (See page 11 for proper salt filling procedure). Make sure you have water, or enough water, in the salt tube (See page 11 for proper salt filling procedure). Ensure there is not TOO MUCH salt in salt tube. If you have overfilled salt tube, you will not allow enough water to convert to brine and flow through cell. (See page 11 for proper salt filling procedure). If you are unable to start up your Mini Pure after trying the two steps above, contact your Distributor, Representative or Viking Pure. Quick Contact Info: ( ) - 16 P a g e

17 Viking Pure: Mini Pure User Reference Guide: Model Number : Serial Number : Installation Date : User Notes: 17 P a g e

18 Other Products by Viking Pure Viking Pure: MiniMAXX Part No: VPM-MAXX Output: 1 Gallon/10 Minutes/Solution Features: 2 X 5 Gallon Storage Tanks with Ball Valve Dispensers Recommended Accessories: Mini Pure Convenience Kit (VPM-CK) Extended Warranty (1,2 or 3 Years Available) Viking Pure 1000 w/ Twin 25 Gallon Tanks Part No: VPT2501 Output: Gallons/Hour/Solution Features: 2 X 25 Gallon Storage Tanks, Ultrasonic Sensors, Pumps, Touch Screen UI Recommended Accessories: Viking Pure 1000 Convenience Kit (VP-CK) Manual Dispense Kit (VPMD100) SanStorm PSV Sprayers, 10 Pack (PSV-HA-CASE) MistaClean PSV Sprayers, 10 Pack (PSV-SH-CASE) Extended Warranty (1,2 or 3 Years Available) Viking Pure 1000 w/ Twin 50 Gallon Tanks Part No: VPT5001 Output: Gallons/Hour/Solution Features: 2 X 50 Gallon Storage Tanks, Ultrasonic Sensors, Pumps, Touch Screen UI Recommended Accessories: Viking Pure 1000 Convenience Kit (VP-CK) Manual Dispense Kit (VPMD100) SanStorm PSV Sprayers, 10 Pack (PSV-HA-CASE) MistaClean PSV Sprayers, 10 Pack (PSV-SH-CASE) Extended Warranty (1,2 or 3 Years Available) 18 P a g e

19 511 Pullman Rd. Unit C5 Edgewater, FL USA Phone: (386) Fax: (386) Website: 19 P a g e