Common Uses for PPC Products on Car Restoration. Diff / Back Axle. Bodywork. Wheels. Fuel Tank. Boxed Chassis. Seats. Chassis. Steering Wheel.

Transcription

1

2 Common Uses for PPC Products on Car Restoration Parts and Tools Derusted With Deox Brakes Caliper Paint Exhaust Hi Temp Heat Paints Carbs 2K Urethane Clear (Glisten PC) Steering Wheel Bakelite Steering Wheel Repair Kit Leatherique Wheel Repair Kit Seats Leatherique Fuel Tank Rust Repair Kit (Internal) POR-15 Rust Preventive Paint (External) Fuel Preservative Bodywork POR-15 Rust Preventive Paint Tie-coat Acid-8 2K Urethane (Hardnose) Top Coats see page Engine Enamels Diff / Back Axle POR-15 Rust Preventive Paint Top Coats see page Wheels Top Coat Silver 2K Urethane Clear (Glisten PC) Wurth Silver and Clear Suspension POR-15 Rust Preventive Paint Top Coats see page Gearbox POR-15 Rust Preventive Paint Top Coats see page Chassis POR-15 Rust Preventive Paint POR-15 Underbody Sealer Top Coats see page Boxed Chassis SW2 Oil Dynax S50 Cavity Wax Dynax UC Dynax UB Picture courtesy of

3 For the full range of products visit: CONTENTS Introduction... 2 Do s & Don ts...3 How to... 4 Preparation Products Marine Clean...5 Metal Prep...5 POR-15 Rust Paint Rust Preventive Paint...6 Super Starter Kit...7 Solvents & Strippers Solvent...8 Paint Stripper...8 Deox-C...9 Deox-Gel...9 SW2 Protective Coat...9 Protective Sealers Dynax S Dynax UC...10 Dynax UB...10 Fillers P38 Filler (Bog) P40 Hole Filler Linking Coats Por Patch Acid Tie-Coat Primer POR-15 Self-Etching Primer Topcoats POR-15 UV Stable Topcoats Top Coat Chassis Black, Semi-Gloss (Chassis Coat) Top Coat Gloss Black (Blackcote) Top Coat Silver (Sterling Silver) Top Coat Cast Iron (Metal Mask) Detail Paint K Urethane (Hardnose) K Urethane White (Whitecote) K Urethane Clear (Glisten PC) AP120 Metal Prep Engine Paints Engine Enamel Glyptal 1201 Internal Engine Coating...20 High Temp Heat Paints...20 Fuel Tank US Tank Sealer...20 Auto Fuel Tank Repair Kit...21 Motorcycle Fuel Tank Repair Kit...21 Kits Super Starter Kit...22 Rust Hole Repair Kit...22 Polished Alloy Resto Kit...22 Leatherique Leather Steering Wheel Kit...23 Caliper Painting Kit...23 U POL Raptor Ute Liner Kit...23 POR-15 OEM Bed Liner...23 Under Body Coating Wurth Rubberized Underbody...24 POR-15 Rubberized Under Coating...24 Dynax UB...24 Car Care PPC Clay Bar...25 Wurth Rubber Stick...25 Wurth Wheel Silver...25 Wurth Screen Wash Additive...25 Auto Wash...26 Auto Foam...26 Auto-Clay...26 Auto Balm...26 Accessories Epoxy Putty...27 Inspection Mirror...27 Paint Brushes...27 Wet and Dry Paper Sand Paper...27 Paint Filters...27 Preval Sprayers...27 Paint Can Spouts...27 Spray Tool...27 Inox...28 Lanox...28 Wurth Rost Off Ice...28 Ballistol...28 Garage Floor Covering...28 Benchtop Sandblaster...29 Abrasive Blasting...29 HVLP Touch Up Gun...29 Leatherique DIY Leather Care...31 Marine Applications...32 For the full range of products visit:

4 2 INTRODUCTION Permanent Painted Coatings have been operating for nearly 20 years marketing through 70 distributors around Australia. We stock the best products selected from around the world. PPC have become experts in rust repair, corrosion and general restoration in the motor, marine and industrial areas. The range of products is extensive, from the well known, POR-15 (USA) Rust Preventative Paints, Eastwood (USA) restoration paints and tools, to Bilt - Hamber s (UK) range of rust removers, waxes, and auto clay. PPC also imports and distributes a full range of Leatherique (USA) products. Their range of products will rejuvenate, clean and restore leather to it s original look. PPC can match existing dyes for a complete restoration. Leatherique customers range from Rolls Royce s, Lotus, Ferrari s and Range Rover s to name a few. Also suitable for most leather products including household lounges. In addition, there is a large range of car care products and tools to help the restorer. What Roy started with Ready for priming Ready for painting Finished restoration

5 For the full range of products visit: INTRODUCTION 3 The Do s and Don ts with POR-15 Rust Preventative Paint We have many thousands of satisfied customers around Australia. POR-15 Inc in the USA has been in operation for more than 40 years and is very well known amongst Restorers, Hot Rod builders, BOATERS and increasingly in industry. A proven product, with a long history. Do s If spraying wear an organic vapour particulate respirator NIOSH/MSHA approved. Do roughen up smooth metal with sandpaper to give it something to bite into. Make sure all the surfaces are very dry before painting. This is IMPORTANT and more so in marine applications. Use a heat gun / hairdryer / blow torch to rid the metal of all moisture. This will ensure the rust won t come back. Wear gloves and protection, POR-15 will stay on your skin for 4-5 days if it s not wiped off with Solvent or thinners immediately. Do apply thin coats of Tie-Coat, thick coats will take days to dry, or use Acid 8 (dries in 1 hour). Stick to the system, we know it works... And when all else fails read the instructions...we have more job failures with professionals than amateurs as they tend to go by past experience with normal paints, not by the POR-15 instructions. Unit 1, 4 Prosperity Parade WARRIEWOOD NSW 2102 Tel: (02) Fax: (02) sales@ppcco.com.au Don ts Don t put a primer on after sandblasting. POR-15 chemically bonds to the metal. Don t shake the tin, it creates bubbles and destroys the smooth brush finish. Don t back track when you re brushing. 3-4 strokes maximum and move on. Don t paint out of the can if you intend to keep any paint in the can. Pour out what you need, keep the rim very clean and seal it with cling wrap before replacing the lid. READ THE DIRECTIONS This is not like ordinary paints! POR-15 is a high tech, high performance coating that will stop rust permanently. It resists chipping and cracking, and is hammer-tough, as long as you follow the directions. It is unlike any paint you have ever used so please don t use old methods that were developed for paints. We supply you with carefully written instructions on a supplementary sheet as well as the label on the item. Please read and follow them carefully. You ll love the results! Everyone who uses the product correctly confirms it does what it says.

6 4 HOW TO POR-15 is a Purpose Designed Paint Choose the right product for your job! POR-15 products work as a complete system. Used together, they stop rust and corrosion and prevent it from returning. Not only are the products in our catalogue available individually, many are also available in cost-saving kits geared to your specific restoration needs. Here is how the system works: NOTE: The application of POR-15 and Preparation Products will depend on the material and environment in which it will be used. Often not all steps are required. POR 15 began over 40 years ago in the U.S.A. Its original purpose was to service the auto, military and motorbike markets. Since then its versatility and durability has seen it put to work in all sorts of areas - many of them quite unexpected; Boats, trailers, homes, factories, helicopters, farms, and mining equipment - the list goes on and on. Wherever there is a need to protect against rust or corrosion or purely for its sheer durability POR-15 is the best product to use. We would love to hear of any new uses (they seem to come up all the time). Please let us know as we can publish them on our website so others can benefit as well. Before We have used an acid damaged and rusty battery tray as our illustrated example as they are a common problem. They can be fixed permanently as battery acid won t affect POR-15, nor will brake fluid (up to dot 4). Get rid of loose rust with wire brush or sandpaper. Clean rust or corroded metal with Marine Clean, a powerful yet environmentally-safe cleaner. Marine Clean removes dirt, grease, wax and other contaminants that could interfere with your restoration. Rinse off well with water (don t use solvent based degreasers like Prepsol). This step is not necessary on newly sandblasted surfaces. A rust remover/primer, Metal Ready neutralises rust and etches metal for better adhesion. It coats the metal surface with zinc phosphate to encourage deep bonding of POR-15 to the base metal and rust. Rinse off with water. Before painting ensure the surface is bone dry. It looks horrible after this step but that s good. After thorough drying (heat gun is best), coat with POR-15 (we used POR-15 silver for the photograph) by painting the rusty or corroded metal with POR-15 Rust Preventive Paint. RIGHT ONTO THE RUST! POR-15 bonds to the rusty metal and forms an unbelievably tough, almost ceramic-like finish that will not crack, chip or peel and stops rust permanently! This stage is not necessary if the parts are not exposed to UV light. (ie. chassis, under vehicles etc.) Now it s topcoat option time: Blackcote, Chassis Coat, Stirling Silver, Engine Enamels, Metal Mask, Hardnose, WhiteCote or any topcoat system. Some applications may need our Tie-Coat primer or Acid8 for proper adhesion. After Now you have a permanently repaired battery tray, that will not rust again, even if you have an old leaky battery! For best results follow the system and read the instructions

7 For the full range of products visit: PREPARATION PRODUCTS 5 Step 1 - Marine Clean (Water Based) Cleans and degreases in one application Marine Clean cleans and degreases in one application without leaving residues, noxious fumes or flammable solvent. It makes petroleum-based cleaners almost obsolete because Marine Clean can be diluted 3,4,5, and even 10 times it s volume while remaining more potent than other cleaners. Marine Clean removes grease, oil, mildew, algae, musty odours, soap films and wax. Use it also to clean canvas, vinyl, nylon, holding tanks, grease traps, auto parts and more. Before applying ANY rust preventative paint or coating, you MUST remove all oily film or residue. Even if you re sure your work is clean hit it with Marine Clean to be certain of good adhesion. This is water based, don t use solvent based cleaners. 1 litre *4 litres *free spray bottle Applications Engines Transmissions Chassis Suspension components Floor pans Fuel Tanks Holding tanks Clothing Waterline scum Rust stain in porcelain sinks Toilets and baths Features Water based concentrate Environmentally safe Works well in cold water, even better in hot Safe on aluminium Emulsifies all oils 1 Mix Marine Clean with water (hot water is best) 2 Apply Marine Clean. 3 Leave on for approx. half an hour, wash off well with water Step 2 - Metal Prep (Metal Ready) Rust remover and Pre-primer Etches metal & leaves a zinc phosphate coating Metal Ready provides the best adhesion on any surface, including aluminium and shiny polished metal surfaces. After thoroughly degreasing your work piece with Marine Clean. Apply Metal Ready, this one step process both neutralises any rust and gently etches any clean bare metal, creating an ideal anchor pattern for coatings such as POR- 15, whilst simultaneously leaving a zinc phosphate coating to promote chemical bonding of the paint to the steel. 250ml 500ml *1 litre *4 litres *free spray bottle 1 Apply Metal Ready to all metal areas to be painted 2 Leave 30 minutes to remove rust and coat with zinc phosphate 3 Rinse with water or wet rag (it will have a salt and pepper look). Dry well (heat gun). Features Easy to use No harmful residues Coats metal with Zinc Phosphate Ensures perfect paint adhesion Provides a perfect base for all paints Removes surface rust in minutes Reusable Gives better welding conductivity

8 6 POR-15 RUST PAINT Step 3 - POR-15 Rust Preventive Paint The applications are endless. If a surface needs protection, or restoration, odds are that POR-15 Rust Preventive Paint will do the job - and keep on doing it. BRUSHABILITY - POR-15 will brush on leaving a spray like finish. A great DIY feature. AUTOS POR-15 is so tough you can hit it with a hammer and do no damage. Yet it also has incredible flexibility and can withstand much twisting and bending without cracking. It can be used on all auto work from chassis, front ends, rear ends, axles, floor pans, fuel tanks, engines, battery boxes (acid does not affect POR-15 nor does brake fluid), to all external work. Even prime your vehicle s exterior. BOATS Boat owners use it in a thousand ways. Below decks for engines, engine mounts, bilges, hull maintenance, sealing tanks. Topside maintenance including decks, handrails, metal fittings, chain lockers, hulls - steel, aluminium, wood and fibreglass. And the POR-15 range can be used as a complete primer system for steel and aluminium boats. HOMES, MINING, FACTORIES The list is endless. If rust, salt or chemical corrosion are problems then POR-15 is the correct product to use - far better than anything else on the market. Chemical plants, sewage works, indoor pools, to name a few. Brush or Spray Features 1 litre covers 5m 2 per 2 coats (we always recommend 2 coats) Compatible with all paint systems Tested to over 250 C Exceeds 2000 hour salt spray test Dries faster in humid conditions Repels all fuels and oils Resistant to most acids and alkalis Over double the solid content of most ordinary paints Self levelling Single component 100ml 500ml 1 litre 4 litres Bend It!! POR-15 won t chip, crack, or peel! Stops rust permanently! Won t crack, chip or peel 1 litre POR-15 will cover 5² metres per 2 coats. (Complete car chassis). New Steel Sandblasted Steel Aluminium Fibreglass Concrete

9 For the full range of products visit: POR-15 RUST PAINT 7 Which colour should I use? Often it s better to use a different colour for subsequent coats, ie. grey and then black, which shows where you ve missed on the previous coat. Black Gloss is our most popular colour and is ideal for automotive work. Suspensions, chassis, floorboards, mudguards, engines, boot area, gearboxes, axles, etc. Black Semi Gloss now available. Grey is an excellent choice for all general work especially machinery. Also as an alternative primer colour to black. This is used a lot in marine applications. Nigel s engine bay before and after POR-15. Silver contains more metal flakes and has a high solid content. Good for smoothing rough pitted areas as a primary coat. Often used in industrial applications. When used as a first coat on rusty areas the rust colour may leach through the paint and should be second coated with black. Clear dries to a perfect finish and is often used as a primer on exterior surfaces before final painting. Ideal for repairing cracked fibreglass - used instead of GRP resin (stress cracking). This is not a final clear coat. See Topcoats Clear. All POR-15 Coatings should be STIRRED, not shaken! POR-15 Rust Preventative Paint is compatible with all paint systems but may need Tie-Coat primer, Acid 8 or specific treatment (sanding / wet coat priming etc) for proper adhesion between POR-15 and the top coat... Paint directly over rust!! No need to remove rust first! Pound It!! It s Hammer-Tough! Super Starter Kit Enough to cover 0.5m 2 (two coats). The complete kit and the best way to test the product or to do small jobs. Includes everything including instructions.

10 8 SOLVENTS & STRIPPERS Solvent Use POR-15 Solvent when thinning or spraying. This is important as regular solvents often contain moisture which can affect POR-15 products. POR Solvent is of high purity with minimal moisture content. It can also be used for thinning most 2 pack products, lacquers and epoxy paints. Do not use other thinners for thinning POR15 products. GP thinners can be used for cleanup. 4 litre 1 litre 500ml Paint Stripper - Gel or Liquid There is not much it won't take off. It resists drying out and will cling to vertical surfaces. Enamels, epoxies, lacquers, polyurethanes and acrylics don't stand a chance. Fast and powerful yet won't damage or etch glass or aluminium. POR-15 Paint Stripper is water soluble making clean up simple and quick with little mess. Apply with a brush, leave minutes. If covered with food wrapping it helps contain the active ingredients and improves the number of coats removed. 4 litre 1 litre Applications All automotive uses including: Panels Doors Floors Wheels Chassis All marine uses above and below decks Furniture Machinery Features Removes the following paint: Enamels Epoxies Lacquers Polyurethanes Acrylics 2 Pack Automotive 2 Pack Marine POR 15 Rust Preventive Paint Won t damage or etch glass or aluminium 1 Old Chevy door coated with several layers of paint. 2 Just brush POR-Strip right onto the painted surface. Almost instantly, POR-Strip begins to bubble the layers of old paint. Brush more, if needed. 3 Layers of old paint then easily scrape off.

11 For the full range of products visit: SOLVENTS & STRIPPERS 9 Deox-C Concentrated rust remover powder Dissolved 1 part powder in 19 parts water, a Deox-C bath will clean the most awkward, heavily rusted items brilliantly with no effort, distortion or health risk at all. Deox-C leaves pure bare metal with no traces of corrosion. Simple to use, economical and saves hours of less effective wire brushing or blast cleaning. Parts are ready for painting or coating. Deox-C can be reused until it turns black. Rusted pliers found in the garden after 10 years. After immersion in Deox-C for 24 hours they are now useable again. 1kg Rusted solid Working again 1kg = 20L mixed Deox-Gel Gelled rust remover If items are too big for a Deox-C bath then use Deox-Gel - the same high-power yet safe active constituents, but in gelled form for brush application. Removes corrosion leaving a bare-metal surface ready for paint or coatings. Approximate coverage 2m 2 per litre. Rusted steel Before After 1kg SW2 Protective Coat It does everything that Fish Oils do - without the stickiness or fishy smell! It has a great capillary action that goes into double folds. If painting is hard or impossible then SW2 is the way to go. Ideal for interior of vehicle doors, body panels, hollow sections of chassis, trapped recesses, etc. This Protective Oil is thin and forms a water resistant, penetrating film which dries to a hard satin coating to prevent condensation rust damage and corrosion. It is also used as a long-term protective film on stored machinery parts, castings and the like. Can be painted over the top which makes it ideal to use between sandblasting and painting if there is going to be a time lag. This hotrod was kept in bare metal for over a year as they worked on it by spraying SW 2 on when they finished filing and sanding. Features Low odour Water resistant Easy application Satin finish 500ml 1 litre 4 litres Anti-corrosive Dries hard

12 10 PROTECTIVE SEALERS Dynax S-50 Cavity wax with hard to reach to applicator Dynax waxes are formulated with high performance anti corrosive properties for protection against corrosion. Dynax S50 is designed for internal use with a long 62cm (2ft) thin spout. Dynax S-50 comes in a large 750 ml aerosol can. A great Cavity Wax with a long thin 360 deg applicator Ideal for all those difficult to get to places Spray areas you can t paint Great for use in box sections Leaves a self healing wax like surface Kills existing corrosion Creeps into seams and welded flanges. Virtually odourless 750 ml Includes extension tube Dynax UC Clear cavity wax Dynax UC - A Clear cavity wax in a double sized 750ml can the new way to protect your car in seconds. Dynax UC new high-performance anti-corrosion wax provides a low film thickness see-through protective shield.. It can be applied to bare metal or painted surfaces in fact anywhere where a discrete and powerful inhibitor is needed. Dynax UC is completely safe to use on the vast majority of paint coatings and is ideal where dark coloured waxes or under seal would detract from the painted finish of vehicle bodywork or underside. The touch dry tough wax film provides mechanical protection to the protected surface too. Dynax UC is ideal for use on lower body panels, chassis, floors, sills, jacking points, chrome, suspension, fixings, wheel arch lips, alloy wheels plus it s perfect for protecting motorcycles, alloys, aluminum, boats, mowers, machinery, tools and equipment too! Dynax UC can be easily removed if required with simple solvent wipes or alkaline degreasers after the aggressive winter months pass or left in place for prolonged protection. The giant 750ml aerosols are equipped with a unique valve and cans charged to 70 psi they work on their side and even upside down. Long term protection in seconds. 750 ml Includes short extension tube Dynax UB Underbody Sealer Anti corrosive heavy duty wax Dynax UB is a heavy duty wax for use on underbodies to protect against corrosion from exposure to beaches and salt air. Dynax UB comes in a large 750 ml aerosol can. UB Anti Corrosive Wax - Heavy duty spray on Good for vehicle underbody and harsh environments Leaves a hard wax surface Better than bitumen type covers, as it won t crack or peel Good for internal high salt exposure areas on boats e.g. drive shafts Jack up the car and spray on two coats over 24 hrs A must if you use your vehicle on the beach Dark brown in colour 750 ml Includes short extension tube

13 For the full range of products visit: FILLERS 11 P38 Filler (Bog) P38 FILLER has over 30% more resin than other fillers, which gives it much greater adhesion. This makes it the recommended choice for applying over POR-15. P38 has ultra fine particles for perfect feathering of edges, and is manufactured under vacuum, which eliminates those pesky air holes you ve experienced with other fillers. It s more flexible, tougher, and able to tolerate higher temperatures than other fillers (you can even use it in a baking oven!). U POL Fillers have been tested to work with POR-15. Many locally made fillers will not adhere to POR litres 100ml Features: 30% more resin (other fillers are loaded with too much talc) Manufactured under vacuum pinholes are greatly reduced! Much more flexible than other fillers Ultra-fine particles, for perfect feathering Ready to sand in 20 minutes or less Tolerates higher temperatures bake oven compatible Excellent for use with two-part or single-part paint systems Low absorption, so that paint doesn t soak into the filler; yields better coverage Convenient packaging; resealable hardener keeps product fresher longer Comes with resin, hardener, and filler applicator & instructions 250ml Application Hint 600ml Paint POR-15 over the rusted area. Apply the P38, sand smooth and then apply another coat of POR-15. This way the metal is sealed and the bog is sandwiched giving a 100% fix. Degrease & sand Mix filler (Ratio pea to golf ball) Apply Sand & prime P40 Hole Filler 1 litre P40 HOLE FILLER is for applications that require more strength, such as bridging holes, or filling high-stress areas. P40 is loaded with tiny polyester fibres, which makes it many times stronger than ordinary body fillers. Use P40 HOLE FILLER in conjunction with POR-15, to make permanent repairs to deep pits or rust holes. Then use the P38 FILLER to finish off the repair, for a final smooth appearance. 600ml 250ml Application Hint Apply 2 coats of POR-15 over the whole area, apply the P40 and the P38 and give it all another coat of POR-15. This way the metal and bog are both sealed in.

14 12 LINKING COATS Por Patch Por Patch is a highly concentrated version of POR-15 Rust Preventive Paint. It comes in a tube and has the consistency of toothpaste making it a most effective filler. When cured, Por Patch is virtually indestructible yet it remains flexible and won t chip or crack. This single component filler not only covers rust and prevents it spreading but also strengthens the underlying metal and seals holes, gaps or seams by forming its own membrane filling and sealing uses - metal, wood, concrete and plastic. Acid 8 Acid 8 works the same as Tie Coat but dries quicker. (Normally about 2 hrs). It s available in both 1 litre cans and the convenient 450 ml aerosol. The 1 litre can doesn t need thinning for spraying. The 450ml aerosol allows a quick spray to etch prime POR-15 (saves sanding) and with the quick drying means the job gets finished sooner. 450ml 1 litre 110g tube in black or pearly white Apply Smooth Tie-Coat Primer Prime and paint over cured POR-15. This very special interlocking primer paints over the top of POR-15 without any need to rough up or de-gloss the surface. Just ensure the surface is free of any grease, oil or dust (use Marine Clean). Tie-Coat is a tough yet sandable single component polyurethane primer with special adhesion characteristics. Which makes it perfect for most painted surfaces - especially POR-15. Tie-Coat applies with brush or spray and is easy to sand to a smooth finish. Only light coats are required. 500ml 1 litre 4 litres Features Use on other painted surfaces with minimal preparation Easy to apply Spray or brush on Single or multiple coats Easy to sand to a smooth finish Single pack Compatible with all paint systems and bake ovens Tie-Coat is a linking coat. Only use thin coats Rusted metal is sealed with our world-famous POR-15 Rust Preventive Coating. Prime over cured POR-15 with Tie-Coat Primer Metal can then be painted with any type or colour of paint, with no need to rough up or de-gloss the POR-15 surface.

15 For the full range of products visit: LINKING COATS 13 POR-15 Self-Etching Primer POR-15 Self-Etching Primer is NOT a high-build primer, it can be sprayed or brushed on almost any painted surface and can be top coated in minutes. It bonds incredibly well to POR-15 Rust Preventive Paint, and all topcoats bond incredibly well to POR- 15 Self-Etching Primer. It can be sanded lightly, and, if desired, multiple coats may be applied. It is available in an aerosol spray. In situations where you are top coating an old POR-15 finish, we first recommend a light sanding with any 280 to 320 grit paper. 425g 946ml For the full range of products visit:

16 14 TOPCOATS POR-15 UV Stable Topcoats Our topcoats are designed to work with POR-15 Rust Prevention Paint but with UV stability. They don t have the same chemical bonding to the metal so both are required for a UV exposed surface. They are highly flexible, non-porous, extremely scratch and chip resistant and strengthen with exposure to moisture. Used over POR-15 they deliver the toughest, most permanent protection against rust and corrosion ever developed. Plus they look terrific! They will cover approx. 10 sq metres per litre and normally need a little thinning with POR-15 Solvent. BlackCote is glossy while Chassis Coat is semi gloss. Stirling Silver is semi gloss. *We suggest spraying the silvers to avoid streaking Back axle half painted using Black Gloss and Top Coat Silver. 425g (Aerosol) 946ml 3.8 litres Top Coat Chassis Black, Semi-Gloss (Chassis Coat) Apply over POR-15 Rust Paint Top Coat Semi Gloss has a smooth, satiny semi-gloss finish and is probably more correct as original for underhood and chassis components for cars produced in the USA from the early 1950 s to today. Top Coat Gloss Black (Blackcote) Apply over POR-15 Rust Paint Top Coat Gloss has a beautiful glossy black finish and is perfect for restoring the gloss black frames, chassis and under hood parts of earlier vehicles. Applications Chassis Floors Boots Inner guards Wheel wells Inside body panels Leaf springs Suspension components Fuel tank exteriors Firewalls Trailers Machinery Truck & trailer units Automotive & marine engines *Chassis Coat doesn t brush as well as other POR-15 products. Marine Applications Hand rails Hatchways Bollards Winches Trailers Features No UV sensitivity, hammer tough, non porous Self levelling - leaves no brush marks, high solids High spread rates High chemical resistance

17 For the full range of products visit: TOPCOATS 15 Top Coat Silver (Sterling Silver) Semi gloss Top Coat Silver is a semi gloss silver with a very high pigment content. Can be used in UV situations like wheels, trailers or external parts. Best applied over POR-15 rust preventative paint, but could be used on it s own. Due to the high pigment content, stir well before use. 425g (Aerosol) 946ml 3.8 litres A UV stable topcoat with a medium-gloss silver appearance. Stirling Silver used on front and rear suspension of a V-W. Stirling Silver (Semi Gloss Silver) Top Coat Cast Iron (Metal Mask) Sandblasted new metal look We have developed a super-tough coating that looks just like bare metal. Now you can permanently coat and protect all those components on your chassis that were left unpainted by the factory when your vehicle was new. Items such as spindles, steering boxes, coil brackets, rear ends, leaf springs, bolt heads, suspension components, master cylinders, coil springs, fuel tanks, cast iron transmission housings, and others will look factory correct when coated with Top Coat Cast Iron. 425g (Aerosol) 946ml 3.8 litres Applications Undercarriages Fuel tanks Engine compartments Hood hinges Master cylinders Springs Latches Bare Metal Grey (Cast Iron)

18 16 TOPCOATS Detail Paint Fast drying for quick & easy handling. Replicates the look of various metals. Resists corrosion & abrasion. POR-15, Detail Paint provides professional grade finishes that reproduce the original look of case parts. POR-15 Detail Paint is perfect for water pumps, intake manifolds and master cylinders. Designed to protect against rust, all the colours are developed to have a low sheen and will not yellow to keep your restored component looking factory new. POR15 Detail Paint is formulated to provide maximum corrosion resistance and protect metal substrates against weather, sunlight, oil and water. For use on bare metal, or for the ultimate protection use over POR-15. Applications For use over prepared metal surfaces Cylinder heads, engine blocks, water pumps, Industrial Interior / exterior railings, storage tanks, machinery, structural steel, piping, steel decking. Cast Aluminium Stainless Steel Cast Iron 425g 454g 425g For the full range of products visit:

19 For the full range of products visit: TOPCOATS 17 2K Urethane (Hardnose) These beautiful Hardnose paints are stronger than any colour paint you have ever used. Their long-lasting, brilliant colours look terrific and will withstand incredible abuse. Hardnose paints hold up under conditions that would quickly destroy other paints. Will not chip, crack or peel, are UV stable, self levelling and will withstand temperatures to 180 C. Hardnose is excellent for heavy duty auto chassis, trailers, footwells and on boats as well as any areas that need protection from acids, alkalis and other aggressive materials. Hardnose can be applied over other single or two pack paints. 340ml pack 1 litre pack (pack contains paint and hardener) NOTE: No coating is as effective as our own POR-15 Rust Preventive Paint for stopping rust. So, if you plan to use Hardnose colours on a rusty item, or one that may rust, first coat the item with POR-15 RPP. Colours Colours shown are a close match but may vary due to printing process limitations. All POR-15 Coatings should be STIRRED, not shaken! Black Dark Grey WhiteCote Dark Green Light Blue Dark Blue Light Yellow Dark Red Light Red Orange Dark Yellow Light Grey Light Green Features High solids 80% Brush or spray High spread rates UV stable Highly resistant to most common chemicals Solvent proof once cured Withstands temperatures to 180 C Applications Chassis Floors Engines Farm equipment Fertiliser machinery and other strong chemical environments Walkways Stairwells All general marine surfaces Including: Companion ways Masts Decks Motors Water pipes (not suitable for permanent immersion)

20 18 TOPCOATS 2K Urethane White (Whitecote) Appliance white 2K Urethane White is glossy appliance white, is UV stable and makes an excellent topcoat for POR-15 Rust Preventive Paint. Being a moisture-cured topcoat it is ideal for refurbishing baths, painting outdoor metal furniture and commercial air conditioning plants, also marine uses from decks to engine rooms; to name a few. It leaves no harsh brush marks, WhiteCote is one of the world s finest white topcoats and represents a major breakthrough in topcoat technology. WhiteCote cures to a rock-hard finish that will not chip, crack or peel. It is non-porous and is highly chemical resistant. Features UV stable High solids Hammer tough Non porous 8+ hours pot life once mixed Highly chemical resistant Many Uses Marine Bath recoating Outdoor furniture 946ml pack 2K Urethane Clear (Glisten PC) Clear coat - available in gloss Glisten PC has all the properties of Hardnose but is a water-clear coat. Like many other POR-15 coatings Glisten PC is a moisture cured coating which means it is strengthened by exposure to moisture. It will not crack, chip, peel or yellow, is very flexible, and UV stable. Glisten PC will not leave brush marks, can be second coated in 30 minutes and will dry in an hour although maximum hardness will take a few days. Typical marine uses are on stanchions, alloys, polished brass work (don t polish again), bright work, polished aluminium, stainless steel (stop the rust weep), decks (instead of varnish), indoor woodwork, etc. Other uses are aluminium and stainless steel wall signs, gold bathroom taps, wood floors and top coating garden furniture, to name a few. It is resistant to most chemicals and acids as well as salt laden atmospheres. Either paint directly on to a surface or use it as a top coat over other paints or metals. Glisten PC normally needs thinning with POR- 15 Solvent. Glisten PC is not recommended to be painted directly on ferrous metals e.g. steel. Use on cabin work and boat decking plus over new metal surfaces such as stainless steel, alloys, brass, aluminium, chrome, etc. Paint Glisten PC over your polished brass, weeping stainless steel and don t polish again. Glisten PC sets new performance levels in adhesion, corrosion protection and UV stability. Glisten is a water clear coat that won t yellow in UV. 340ml pack 1 litre pack (pictured) 4 litre pack (pack contains paint and hardener) Features Tested to 180 C Bonds to polished metals and POR-15 Hammer-tough Tack free in 30 minutes (20 C) Easy to clean Unaffected by diesel, petrol, acids, solvents Applications Transport industry applications Rims, pressure vessels, bull bars, fuel tanks Aluminium tanker bodies, alloy wheels, inlet manifolds, superchargers, stainless steel, signs, brass CLEAR, HIGH GLOSS! Will not yellow! AP120 Metal Prep Our AP 120 is recommended as an etching primer/cleaner for use with alloys (non ferrous metals). It has been proven to give a 30-40% better adhesion. Ensures high adhesion levels on alloys and other metals without tarnishing the surface. AP120 is a must when using Glisten PC on alloy surfaces. Also improves adhesion on other surfaces - glass, chrome, stainless steel. Apply and leave for approx. 1 minute (do not allow to dry) and wash off with water. Dry the surface very well. t This product can reduce polished shine. 500ml sprayer 4 litres with a free spray bottle

21 For the full range of products visit: ENGINE PAINTS 19 Engine Enamel POR-15 Engine Enamels are superior quality with 80% solids (pigments) and therefore they flow easily, cover better (normally only one brush coat is required, two if sprayed), are guaranteed not to burn off and last longer than any other product. Quite simply, POR-15 Engine Enamels are the best available. Cheap paints use inexpensive fillers to mask their lack of proper pigmentation and depth. They usually contain a high proportion of solvents which evaporate quickly. 473ml Features High solids 80% Self levelling Guaranteed not to burn off Rich colours One can will paint most engines twice No need to remove existing coatings Applications Engines of all descriptions Cars, trucks, marine Farm machinery, generators Stationary engines Colours Colours shown are a close match but may vary due to printing process limitations. Ford Green Ford Red Ford Corp Blue Chrysler Hemi Orange Chrysler Blue Chevrolet Blue 6cyl Chevrolet Red V8 s Chevrolet Orange Most V8 s Buick Green Buick Turquoise 42-52, 53 Special BMC Green MG Maroon White Black Yellow Aluminium Gold Cadillac Dark Blue Chrysler Turquoise , Ford Medium Blue All Ford products Pontiac Light Blue Don t expect them to cure quickly! (2-3 days) Nigel s engine before. Nigel s engine painted with Engine enamel Paul s engine block in Gold

22 20 ENGINE PAINTS Glyptal 1201 Internal Engine Coating Glyptal 1201 is a specialised, air dried enamel coating, used in the USA for over 30 years. For the engine restorer it s used as an internal engine coating, (amongst other electrical industry applications for insulation). We have frequently been asked for this product, particularly for older restorations with motors that are slightly porous. It s resistance to oil is excellent, and water, acid, salt water, is good. Air dried or it can be baked to a smooth finish. Designed to withstand continuous temp of 135º C. It can be thinned with POR-15 solvent. 450ml 950ml High Temp Heat Paints For best results sandblast your manifold to ensure surface is totally clean and ready for painting. May require thinning. 425g (Aerosol) 250ml 500ml Brilliant Aluminium Capable of withstanding 760 C, Brilliant Aluminium is also extremely weather, salt and moisture resistant. It helps prevent cracking, chipping and peeling. This is the most brilliant, uniform, heat-resistant coating available. Black Velvet A black paint that withstands temperatures up to 650 C and keeps its rich, black colour. Matte finish. Factory Manifold Grey Looks like original factory cast iron with a flat, non-gloss finish. Withstands temperatures up to 760 C and will not burn off. Apply thin coats only. When brushing it may require POR-15 solvent. Applications Manifolds Headers Exhaust pipes Brake calipers Boilers Engines Steam pipes Stoves Grills Stacks US Tank Sealer Not affected by ethanol (E10) Seals pinholes and seams and now sold all over the world. US Standard Fuel Tank Sealer is the toughest non-porous flexible coating made. Forget zinc chromate and rust inhibitors. The only way to stop rust is to keep moisture away from metal. Only a non-porous paint keeps the moisture away. US Standard Fuel Tank Sealer is the only one tested and proven to work with all fuels including ethanol and methanol. It has superior strength, is fuel resistant, and is non-flammable. 250ml 500ml 1 litre Should be used with Marine Clean and Metal Ready for best results. It s more cost effective to purchase as a kit. (See next page.)

23 For the full range of products visit: FUEL TANK 21 Is your tank rusty, leaking or just in poor condition? Save buying a new petrol tank! Give it a new ceramic like internal finish and stop all that dirt going into the jets or injectors and blocking them up. One of our largest selling Australian kits. Auto Fuel Tank Repair Kit Up to 100 litre tank Use our easy 3 stage process. A fuel tank repair is more than just pouring in sealer and sloshing it around. Gum, varnish, sludge or fuel are inside they must be removed first. Our US Standard Fuel Tank Sealer, like other sealers, will not work in a contaminated tank. Features Cleans all sludge, gum & varnish from within the tank Removes rust, preps inside the tank with zinc phosphate for added adhesion Seals with a non porous coating Compatible with all fuels Remains flexible Kit Contains 4 litres of Marine Clean - cleans tank 1 litre Metal Ready - preps tank 1 litre US Standard Fuel Tank Sealer - seals tank Repair material for small holes, leaks Detailed instructions Mirror These tank kits are used by the military both here and in the USA. 1 Remove gum & varnish 2 Remove rust & etch 3 Pour in sealer This will leave a hard ceramic like coating over the inside of your tank. For a lot less than buying another tank you can re-new your old rusty tank and stop rust and gum blocking up jets and filters. Motorcycle Fuel Tank Repair Kit Up to 20 litre tank These kits are specially designed for bikes and other small petrol tanks - outboards, chainsaws, recreational vehicles, lawn mowers, generators, etc. An easy three stage DIY process and the kit comes complete with everything to do the job. For fibreglass tanks contact us. Not suitable for plastic tanks. Kit Contains 1 litre Marine Clean 1 litre Metal Ready 250ml Standard Fuel Tank sealer (enough for a 20 litre tank) Detailed instructions Not affected by ethanol (E10).

24 22 KITS Super Starter Kit Gets you off and running! This Starter Kit will prove how incredible POR-15 really is. The best way to test the product or to do small jobs of about half a square metre. This kit gives you the cleaner, the etching primer/ rust remover and POR-15 rust preventative paint with your choice of colour. It's one of our most popular items. It allows customers to try out the incredible POR-15 rust-stopping system and is essential if your job has oily or greasy residue, or you are using new steel or aluminium. Enough to cover 1m2 with one coat. Kit Contains 100ml POR-15 Rust Preventive Paint in either Black, Silver, Grey or Clear 250ml bottle of Marine Clean 250ml bottle of Metal Ready 2 brushes Pair of gloves Detailed instructions Applications Minor jobs, approximately 0.5m2 coverage Battery boxes, BBQs, garage hinges, car windows Rusty gutters, farm equipment plus many marine applications Rust Hole Repair Kit This kit includes everything you need to professionally repair small rusted out areas in panels and small rust holes. Your kit contains Metal Ready etcher, POR 15 Rust Preventive Paint, P40 to repair holes in panel, P38 to smooth the finish and for filling minor dents and scratches. Plus Tie-Coat, a sandable primer to link the POR-15 to your choice of top coat. Enough for 2 to 3 good sized hole repairs. Kit Contains 250ml Metal Ready 100ml POR 15 Rust Preventive Paint 100ml P40 100ml P38 100ml Tie-Coat Sandpaper 3 brushes 1 pair gloves Detailed instructions Polished Alloy Resto Kit With this great kit you can restore, beautify and protect the alloy parts of motorcycles, cars, trucks and boats. Hammer-tough and can be applied by either brush or spray gun. BEFORE This aluminium wheel has ugly corrosion underneath a thick, yellowed original finish. 1 Remove the remnants of the original wheel clearcoating. 2 After cleaning, polish wheels with the provided polishing compounds. 3 After final buffing, coat wheels with GLISTEN PC to protect that like-new shine! Kit Contains 340ml Glisten PC pack (Hardener & Resin) 250ml POR-15 Solvent 250ml AP x 75ml Autosol 2 brushes Measuring scoop Gloves Detailed instructions

25 For the full range of products visit: KITS 23 Leatherique Leather Steering Wheel Kit This kit supplies everything you need to bring your tired looking leather steering wheel back to good as new. The kit includes: Leatherique Rejuvenator Oil, Prestine Clean, Prepping Agent, Crack Filler, Black Dye and the finishing Klear Kote dye and instructions. You ll be amazed at the results and it s very DIY friendly. Colours other than black can be supplied on request. Caliper Painting Kit Dress up your Calipers! Nothing ruins the appearance of a sharp set of wheels like dirty, corroded calipers lurking from behind. Now, dress up those steel or aluminum calipers with a super-tough durable finish that will make your car or truck look terrific. Our new air dry Caliper Paint is beautiful in appearance, and strong enough to withstand the punishment of road debris and temperature extremes. And it looks terrific on any car or truck. Then, whenever your calipers get covered with dirt and brake dust, clean them with anything you like; the Por- 15 Caliper Paint will stand up to just about anything. Available in: Red, Yellow, Blue, Silver, Black. Kit Contains Caliper Cleaner Por-15 Rust Preventive Paint 1 Roll Masking Tape Caliper Prep Caliper Paint 2 Pair Gloves 2 Foam Brushes Detailed instructions Enough to cover 4 calipers U POL Raptor Ute Liner Kit Available in black or tintable This is a 2-pack heavy duty urethane tintable coating. It s supplied as a 4 litre pack which is good for the largest utes. Can be sprayed with a schutz gun, brushed or rollered. It will adhere to almost any substrate. It protects against abrasion, salt air, rust and helps deaden sound. Remains flexible. Touch dry in an hour, full cure in 5-7 days. Can be used on Utes, 4wd s,rv s, boats and heavy machinery. (Tintable liner can be tinted with base coat tinters). POR-15 OEM Bed Liner Available in black or tintable POR-15 OEM Bed Liner is formulated to provide professional results and performance in a DIY system that can be brushed, rolled or sprayed. It is a water-based, rubberized coating ideal for protecting truck beds, and all other metal, aluminium, fiberglass, and wood surfaces that are exposed to impact and scuff related environments. It is low odour that can be cleaned with soap and water without a limiting pot life. Recommended Uses Metal Truck Beds Trailers Rocker Panels Metal Wood Boat Docks Fiberglass Tractor Beds Aluminium Tool Boxes Running Boards Work Van Floors

26 24 UNDER BODY COATING Wurth Rubberized Underbody Wurth gravel throw and underbody protection For new, restoration (and repair of the original texture) protection against stone chips and corrosion in all visible areas, e.g. front and rear valances, side skirts, bumpers and chassis of cars, trucks and buses. Excellent for use as anti-drone mass for wheel wells and chassis. Good adhesion, quick skin formation, scratch resistant. Suitable for painting over all conventional solvent and water based one and two component top coat paints. Suitable for oven drying at 40 C to 60 C Note: Do not spray on joints, engines, transmissions and brake systems. Cannot be mixed with thinner, water or paint. The product can be painted over within 24 hours. Only sanding and cleaning are then required before it can be painted over. 1 litre POR-15 Rubberized Under Coating POR-15 Rubberized Under Coating can be applied directly over POR-15 Rust Preventive Paint for the toughest rust, corrosion and moisture barrier possible along with excellent sound and vibration deadening. POR-15 Rubberized Under Coating is a flexible, paintable, black coating. It is the only undercoating with POR-15 Technology and will protect against moisture, dust, heat and cold. It s an excellent moisture barrier for application over auto body repairs and creates an effective sound barrier that reduces vibration and deadens sound in wheel wells, quarter panels, fenders and under carriages. Provides superior adhesion to both painted and unpainted surfaces. POR-15 Rubberized Under Coating has superior resistance to road salt and will resist chipping and abrasions. May be used to insulate against engine and muffler noise, protects against dust penetration and exhaust fumes. 421g Dynax UB Underbody Sealer Anti corrosive heavy duty wax Dynax UB is a heavy duty wax for use on underbodies to protect against corrosion from exposure to beaches and salt air. Dynax UB comes in a large 750 ml aerosol can. UB Anti Corrosive Wax - Heavy duty spray on Good for vehicle underbody and harsh environments Leaves a hard wax surface Better than bitumen type covers, as it won t crack or peel Good for internal high salt exposure areas on boats e.g. drive shafts Jack up the car and spray on two coats over 24 hrs A must if you use your vehicle on the beach Dark brown in colour 750 ml Includes short extension tube

27 For the full range of products visit: CAR CARE 25 PPC Clay Bar See & feel the difference. A must for a concourse or show & shine. Fast, safe and easy to use Remove over spray An important step before buffing, waxing, or polishing The ultimate pre-wax cleaner Removes stubborn surface contaminants that ordinary washing, waxing or buffing cannot No drying Very good quality & pricing GREAT PRICE Use the detail spray to wet the surface and rub the clay... it s that easy to clean & smooth the paint finish! You can use the detail spray on it s own for a great finish. The fastest, easiest & most effective way to clean, smooth, shine & protect vehicle surfaces. 200g Wurth Rubber Stick What a great idea! Wurth s rubber care formula is packaged in a convenient sponge-tipped bottle.. No applicators, no mess! Inside this clever bottle is an excellent rubber preservative. It hydrates rubber components to keep them soft and supple. Healthy rubber forms a weatherproof seal inside your doors and trunk lid to keep noise, heat, or cold out. Wurth Rubber Care Gel Stick is silicone-free, bio-degradable, and water repellant. Treated rubber will resist diluted acids and alkaline substances. Strong alkaline cleaners will not degrade the protected rubber. It will also resist salt water, which is essential if you live by the ocean. Use the innovative Wurth Rubber Care Gel Stick on all automotive door seals, gaskets and on weatherstripping around doors and windows in your home for maximum resiliency with minimum mess. 75ml Wurth Wheel Silver Get those wheels or hubcaps looking good again. Wurth Silver Wheel Paint is used to refinish dull or scuffed wheels and hub caps. The fine mist spray goes on evenly and matches all German-made wheels. If your vehicle is not German-made, test an inconspicuous area before doing touch-ups on the outer face of your wheel. If your wheels all need total refinishing, this durable silver paint will work for any wheels. Remove your wheel and clean them thoroughly (POR-15 s Marine Clean works well here) before spraying it. This works on both plastic hubcaps and painted wheels. 400ml Wurth Screen Wash Additive This is a great, very concentrated, cleaner additive for your windshield washer or separate cleaner bottle, if you have one. Calcium inhibitors in the Wurth washer prevent deposits that cloud your visibility that build up in time and plain water just doesn t remove them. Your windshield stays clean and clear no matter what the conditions are outside. If you live in the mountains it s also a great anti freeze in your windscreen washer. Just mix Wurth Screen Washer Additive with water according to the directions, you only need a little at a time, the bottle is good for about 6-8 mixes in a normal washer bottle making it about $1.00 a time. Overspray will not affect your paint, lens covers, or rubber gaskets. We ve all used it and maintain it s one of the best on the market. 32ml

28 26 CAR CARE Auto Wash Highly concentrated vehicle shampoo Autowash is highly concentrated - just a 5ml (1 teaspoon) to a 9 litre bucket is sufficient Highly concentrated. Will chamois off with effortless ease. Gently lifts dirt away from paintwork. 60 washes from one bottle. Supplied in a durable container. 300ml Auto Foam Auto Foam is designed to be used with a pressure washer. Bilt-Hamber Auto-foam is a foaming water-based pre wash treatment, designed to soak and saturate soiled vehicle paintwork prior to the application of vehicle shampoo. Auto-foam is gentle and for use with all pressure washer foam lances. Applied at a typical Panel Impact Ratio of 4%. It will panel dwell for typically 5-8 min. The effects of road grime are neutralised, being bonded within our blend of surfactants, then lifted from painted surfaces and removed. 5 litres Auto-Clay The new flexible bar that deep-cleans paint, regular or soft Rub Auto-Clay over washed car paint to effortlessly deep-clean and remove all embedded matter, insect deposits, overspray and tree sap. Leaves the paint glass-smooth and ready for waxing to the highest shine possible. Unbelievable results. Use before polishing and your car will look stunning! 200g Auto Balm Superior gloss protection system If you live on the coast or need a very good finish polish then this is for you. It is not a cutting polish but a very long lasting high gloss finish providing excellent protection. It will also protect and shine chrome, aluminium, and alloys. If the paint is faded or scratched a cutting compound should be used first. Auto-balm will provide an anticorrosion barrier to stone-chipping. We use it and highly recommend it. 300ml For the full range of products visit:

29 For the full range of products visit: ACCESSORIES 27 Epoxy Putty Epoxy Putty mixes like clay - hardens like steel. Our Epoxy Putty is so strong you can drill and tap it - yet is gentle enough to apply with your bare fingers. Water-based, it sticks even to damp surfaces and will cure underwater and when cured it's rock hard! Large 450g pack Applications Leaking showers Plumbing fixtures Steering wheels Woodwork Fill rust pits/small holes in steel Swimming pools Plastic parts/knobs Paint Brushes Inspection Mirror A small 30mm telescopic ball joint Mirror that extends to 480mm and has a magnetic base. Great for those impossible places. If you own a boat this is a must. These are now supplied in our Fuel tank kits. Due to our volume purchases the pricing is very good. Wet and Dry Paper Sand Paper We stock a range of good quality wet and dry paper in the following grits. 360, 400, 600, 800, 1200, 1500, Genuine bristle brushes at throw-away prices. 13mm, 25mm, 38mm & 50mm Paint Filters There is nothing worse than doing an excellent paint job only to find there is un-milled bits or dust in the paint. Pre filtering through a paint filter ensures a perfect job. These are sold in packs of 10. Paint Can Spouts Preval Sprayers Spray anything, anywhere - without spray equipment. Sprays two packs, single packs, colour coats, primers, topcoats and, of course, POR-15. Just mix paint, pour into glass jar and spray away. Sprays up to 500ml of paint - or for small jobs, clean with solvent and use again another day. A must for every workshop. POR-15 flexible Paint Can Spouts snap onto the rim to keep groove free of paint. Avoid messy drips and paint runs down side of can. Ensures air tight re-seal. Features Fits 500ml to 4 litre cans. Also acts as brush rest and wiper Not affected by paint or solvents Easy to clean - dry and the paint pops off 500ml 4 litres Spray Tool 1 litre Want to do a small touch-up but don t like the hassle of cleaning a paint gun? Try this convenient Reusable Sprayer. Great for small jobs, touch-ups and applying our high temp coatings! Easy clean-up too. Sprays most paints and liquids up to the viscosity of light oil. Just fill the bottle, screw it into place, and you re ready to go! Includes 8 oz. bottle, spray head with 3 interchangeable spray tip inserts, two 184 g cans of propellant, and complete instructions on label. 6 month manufacturer s defect warranty.

30 28 ACCESSORIES Inox Displaces, penetrates, lubricates & protects INOX contains no silicon, acid, kerosene or dieselene. Great where a water proofing lubricant is needed. Outboards, fishing reels etc. It will not harm metal points or surfaces, plastics, paints, enamels, fibreglass, formica or neoprene seals. 300g 5litre 20litre Lanox Penetrates, lubricates & leaves a protective coating Lanolin is a natural wax found in animal wool, especially from sheep. It is a corrosion and waterproofing agent for a variety of metals, materials, timbers, to protect sails, leather, outboard motors, fishing equipment, etc. all areas where a protective residue is required, LANOX would be better suited. Contains no silicon, kerosene, acids or dieselene. Doesn t become sticky, gooey or gum up is harmless to metal points & surfaces, plastics, painted & enamel finishes, fibreglass, formica, rubber or neoprene seals, is nonconductive, non-static & non-corrosive. 300g 5litre 20litre Wurth Rost Off Ice Ballistol High-grade rust loosener with cracking effect created by extreme cooling, and excellent creeping properties. Cracking effect. When the surface of the material, e.g. that of a threaded bolt, is cooled down to -40 o C, microscopic cracks appear in the layer of corrosion of the joints, and these cracks break up the rust and therefore ensure better penetration by the active substance. Phenomenal capillary action. Badly rusted-up screw connections can be easily loosened without damaging the bolts. 400ml BALLISTOL can be used to lubricate practically anything on and around cars, boats, motorcycles etc. Since BALLISTOL is non-toxic so it is safe for use inside a car or boat in areas where people might touch it. You can lubricate practically any material. It can be used on all metals and all plastics. Zippers on convertibles (Jeep etc.), door hinges, locks, antennas, switches, threads on lugs and nuts, adjustable seals, sliding car windows etc. This is a favourite in the gun clubs and military as a lubricant / cleaner on all weapons. 200 & 400ml (aerosol) 500ml (pure oil) Garage Floor Covering Por-15 floor armor Seal your garage floor permanently, with all-new Floor Armor floor painting kits, from POR-15. Vacuum away any dust or dirt, and paint right over everything with Floor Armor. Use Floor Armor in heavy traffic areas. It can take the abuse from forklifts, floor jacks, and constant traffic. Once your floor is covered with Floor Armor, you ll wipe up oil and grease stains with a rag, and keep dust down too. An Easy DIY project that can transform your garage. Colour choices for all kits are Light Grey, Dark Grey, Beige, Tan and White.5 gallon (18.9 litre) covers approximately 92m 2. No acid washing needed. Just vacuum & paint! 2 1/2 car Kits (56m 2 ) Contains Colour Topcoat, Hardener/Activator Grease & Oil Remover Non-slip Aggregate 1-1/4 Nap Roller 1-1/2 Nap Roller 1-9 Birdcage Frame 2.5 Chip Brush Stir Stick Rubber Gloves Additional for Deluxe Kit Clearcoat Topcoat Decorative Chips: Available in white with / Black, Blue or Tan

31 For the full range of products visit: ACCESSORIES 29 Benchtop Sandblaster A great new toy for the shed. A desktop sand blasting cabinet that won t break the bank. A great present for the hard-to-please Dad. Sand or bead blast all those small parts to get the professional finish the pros get. Comes with an internal light, built-in heavy duty protective gloves, spare tear off viewing sheets, spare nozzles and all fittings. It s very easy to use and gives great results; can even be used for designs on glass. Size is 58cm x 48cm x 49cm and weighs 20kg. Compressor requirement is a constant 5cfm at 80 psi. We can supply 12.5kg pails or 25kg bags of glass or garnet beads but due to the different blasting requirements these are not supplied with the kit. Using the PPC Sand Blaster We strongly recommend the use of a mask to avoid inhalation of fine dust and particles. Keep the filters clean. Blocked filters will start dust blowing past the door seals. Dirty Abrasive powder will cause both excessive clogging of the filters and dust escaping through the door. Spare parts are available from PPC a) See-through tear sheets b) Gloves c) Filters Demo photo only (Lid is closed when sandblaster is in use) Abrasive Blasting When using the PPC Blast Cabinet, a variety of dry abrasives can be used depending on the requirements of the user. Generally, the higher the grit number, the finer the abrasive. The finer the abrasive, the smoother the finish. Coarse-grit abrasives, cut fast, but the finish isn t quite as smooth as with fine-grit abrasives. Most popular abrasives are Glass Beads. When abrasive blasting aluminium, brass or softer metals, use a lower air pressure (40-60 psi) for the best results. The same applies to carving or etching glass. Hard metals can be cleaned best using psi. We have found that for badly rusted metal, garnet chips work best. HVLP Touch Up Gun H-2000 (0.8mm) The HVLP gravity gun is ideal for all refinishing work. Complete with pot, spanner, filter and cleaning tool. Minimum compressor size 4 cfm. PPC s direct imported HVLP Touch Up Gun

32 30 LEATHERIQUE This is the original formula; a patented, ph-correct blend of natural oils, fats and collagen to nourish and maintain healthy leather and restore luxurious suppleness, adding new life to tired leather. Leatherique restores cardboard-hard leather. It does not contain greasy oils or cheap watery fillers, waxes, silicones, or mineral oils. Leatherique Rejuvenator Oil deeply conditions and softens your leather while bringing ingrained dirt to the surface. The dirt is then removed with Leatherique Prestine Clean. Leatherique is not a surface dressing, as are many leather products, but treats the full depth of the leather. It s easy to use and gives unsurpassed results. Leatherique Rejuvenator and Prestine Clean are the preferred choice of many USA museums, restoration shops, and do-it-yourself enthusiasts. There are several methods to use depending on the condition of your leather. Cleaning, Maintaining, Rejuvenation and Complete Restoration. Maintaining: Use the Rejuvenator Oil annually to maintain healthy supple leather. Rejuvenating: Use the Rejuvenator Oil and Prestine Clean to restore the suppleness and softness of your leather s original condition. Cleaning: Use the Prestine Clean as an excellent leather cleaner. Complete restoration: A full leather restoration after the above rejuvenation including filling cracks and re-dying either to match the original or choose a new colour. Leatherique Crack Fillers and Colour Fast Dyes are customised to your choice of colour. Leather Dye PPC supplies Leatherique leather dyes. These dyes are colour matched from sample supplied by customers. We can generally match any colour and the Leatherique dyes work on leather and vinyl. All dyes are specially formulated in Sydney. Colour samples can also be obtained on our website. (See pics on next page). Canvas Dye Ask about our Leatherique Canvas Waterproofing & Colour Dyes. Great for renewing canvas on your pop-tops or campers. (See pics on next page). Described as Simply the Best for leather by the Rolls Royce Owners Club of USA since This job is in the realms of the average DIY person. Rejuvenator Oil and Prestine Clean only Before After 1972 Rover 3500 seat - right hand side treated with Rejuvenator Oil and Prestine Clean only

33 For the full range of products visit: DIY LEATHER CARE 31 Rejuvenator Oil and Prestine Clean only Before Leather lounge before Leatherique condition and clean treatment After Leather lounge after Leatherique condition and clean treatment only (not re-coloured) Some full restorations using the Prepping Agent, Crack Filler and Matched Dye Before After 1971 Rolls-Royce before and after full Leatherique treatment inc. colour and Crack Filler Before Leather lounge before full Leatherique treatment After Leather lounge after full Leatherique treatment (including colour) Before Ferrari seat before full Leatherique treatment After Ferrari seat after full Leatherique treatment (including colour) Re-dye and waterproof canvas Before Pop Top van before Leatherique canvas dye After The finished project. 1 litre canvas dye.

34 32 MARINE APPLICATIONS Marine Applications POR-15 paints are ideal in Marine applications but there are a few MUST do s to get the right results. Clean and Dry Firstly prior to applying POR-15 Rust Preventative Paint (RPP) all loose flakey metal should be removed and the metal must be clean and DRY. Steel can harbour moisture in the pores and the more rusted it is the more likely it is to have moisture in it. Any moisture drops left behind when it s painted over will come back as rust bubbles. Salt is hydroscopic and will also harbour moisture. So we need a clean and dry surface. Number of Coats We always recommend a minimum of two coats and three in a marine application for two reasons. One is to make sure that there is 100% coverage and no pinholes left in the coating for moisture to get through to the metal. The other is to build up a good coating thickness. UV Stability and Underwater POR-15 Rust Preventative Paint (RPP) is not UV stable and so it does need a top coat if exposed to the sun. If it is submersed permanently (on the keel, rudders etc) then it also needs to be top coated prior to antifoul being applied. Planning the Job As you need to do the right prepping for a good result and with POR-15 Rust Preventive Paint needing to be applied in 3-5 hour intervals you need to plan your timing fairly carefully. Do all the prepping prior to painting day, make sure there is no dew etc. Start early, POR-15 Rust Preventative Paint also needs time to cure, minimum 3-5 days, before being submersed. The normal up the slip and back into the water as soon as possible (I know slip time costs money) will not get the best results and can leave a soft POR-15 coating. It is better to paint in sections and get the timing right between coats. Avoid sea breezes bringing in moist damp air in the late afternoon between coats it won t stick to a moist surface, we re back to, DRY again.. Cover overnight. POR-15 Rust Preventative Paint will cover approximately 10 sq metres per litre per coat. Marine Clean and Metal Ready will do slightly more. One of the best ways to apply the top coat is to apply a dust coat of the primer for the top coat on to a tacky last coat of POR Rust Preventative Paint. Allow to cure and then apply a full primer coat and then the top coat. Our Tie-Coat or U Pol Acid 8 as the linking coat can both be applied to cured POR-15 Rust Preventative Paint but should not be left exposed to the elements before top coating with whatever paint you desire. Glisten PC (clear coat) will cover aprox 14 sq metre per litre. Glisten PC applied on wood should be treated like a varnish and have multiple coats applied to dry wood. Where to Use it POR-15 can be used with excellent results on Steel boats, Ferro Cement, aluminium, wood and the POR-15 Clear is very good on fibre glass particularly where you get stress cracking. Applications are endless and we have a range of products from Whitecote for decks and masts etc. to Glisten PC on brass, stainless steel aluminium as well as woodwork and Pelucid for indoor woodwork. When in doubt phone and ask. That s what we re here for. Painted with POR-15 and 2 pack epoxy as a top coat. The inside is also POR-15 coated. Marine Gearbox with POR 15 Rust Paint and Topcoat Silver

35 Common Uses for PPC Products on a Boat Stainless / Brass 2K Urethane Clear (Glisten PC) Stress Cracks (Fibreglass) POR-15 Rust Preventive Paint, Clear Woodwork (Internal) Top Coats see page Leather / Vinyl Leatherique Leather care Masts on Yachts Top Coats see page Winch Equip. POR-15 Rust Preventive Paint Top Coats see page Teak Steps Lanox Fish Hatch / Cold Rooms POR-15 Rust Preventive Paint Hull Deck (Steel/Wood/Cement) POR-15 Rust Preventive Paint Top Coats see page Fuel tanks (External) POR-15 Rust Preventive Paint Engines Engine Enamels Fuel Tanks (Internal) US Tank Sealer Exhausts POR-15 Rust Preventive Paint Heat Paint Engine Enamel Bilge areas. (Fibreglass/wood/Steel) POR-15 Rust Preventive Paint Top Coats see page Electrical / General Inox Lanox

36 For the full range of products visit: National Office PERMANENT PAINTED COATINGS Unit 1/4 Prosperity Pde. Warriewood, Sydney, NSW, 2102 Ph: South Australia PAINT SUPPLIES PTY LTD Cnr. West Lakes Boulevard & Phillips Crescent, Hendon, SA, 5014 Ph: Fax: Western Australia AUTOMOTIVE PAINT, TOOLS AND EQUIPMENT 14 Gibbs Street East Cannington, WA, 6107 Ph: Your nearest distributor: Permanent Painted Coatings Pty Limited is sole Australian distributor for POR-15 products. POR-15 products and trade names are the sole property of POR-15 Inc. Product sizes and specifications may change without notice.