Generic Notices. 2) Click on appropriate Service Notice

Transcription

1 Service Notices Generic Notices 1) Select the Bookmark option 2) Click on appropriate Service Notice Service Notice Numbering and Tracking System The following layout is using a single part number for reference 65L614 Rubber Plug 8 characters used as a "File Name" on the computer system Subdivision related to the part "14" which will continually increase as the number of Lubrication Notices are created. Type of part - Main Division, such as "14" for Lubrication or "44" for Shafts or "00" for an assembled component. Designates Seamer Model Number Revisions to existing Service Notices will be as follows:the "File Name" will be duplicated on the Service Notice with the latest revision level designated by a letter. Example: "A". Revision levels on Service Notices are rare but can happen. The Service Notice will provide remaining needed information. Angelus 4900 Pacific Blvd. Los Angeles, CA Tel: (323) /1

2 SERVICE NOTICE ALL /22/98 Oxidation Removal Procedure Scope: Certain alloys of Stainless Steel material are susceptible to oxidation (rusting) when exposed to humid or moist environments for long periods of time or subject to certain chemicals that will accelerate the oxidation process. Regular maintenance of these materials will be necessary to prolong the life of the materials and remain acceptable and safe around consumable products. Description: Oxidation of this type will start as a black or brownish color in the first stages, later turning a deep orange color. It will start in streaks, feel rough and advanced stages will produce a red dust on the surface. How to Clean Oxidation from Stainless Steel materials. Tools: Scotch Bright Pads Eye Protection Wiping Rags Suggested Oxidation (rust) Remover Biodegradable Corrosion Treatment and Preventive that will not affect paint or skin and has no disposal restrictions such as made by *"Rusteco". Method of removal Soak severely rusted parts for 12 to 24 hours. Wipe Dry. Spray surface rusted parts and scrub using Scotch Bright pads. Wipe parts dry, do not wash or rinse with water. CAUTION: EYE IRRITANT: FLUSH EYE CONTACT WITH PLENTY OF WATER AND SEEK MEDICAL ATTENTION *"Rusteco" For more information call, RUSTECO TMT Services Corp. P.O. Box Torrance, Ca Material Safety Data Sheets attached. ANGELUS SANITARY CAN MACHINE COMPANY

3 SERVICE NOTICE 2/9/98-ALL00002 Product Air Content Top Cone w/gasket, Thumb Screws Cone Test Fixture and threaded rod. Scope: This test is designed to check air content in the product of a filled can as removed from the Seamer Can Feed Extension. Description: The test device is made up of a Plastic Base cut to fit the bottom of the can and a coned top with gasket to fit down into the can opening. There are three allthread screws and three thumb nuts used to clamp the Cone w/gasket over the top of the filled can. Procedure: Remove a filled can from the Can Feed Extension. Place the filled can into the fixture and turn thumb screws down to seal off the can. The cone displaces the head space in the can Fixture base cut to fit the foot and may force some additional product out. of the can. Follow instructions for the Zahm Test found in the back of Service Manuals under the Undercover Gassing section. A small puncture at the base of the side of the can will allow any air to enter the Zahm tester funnel submerged in the tank water. The filled can and fixture prior to checking air content. ANGELUS SANITARY CAN MACHINE COMPANY

4 SERVICE NOTICE 5/18/95-ALL00003 ANGELUS SEAMERS Subject: Recommended Seamer Speeds, All Seamers are designed to produce cans or canned goods at a recommended top speed. Top speeds of the Seamers are always dependant on the product or related equipment. Recommended maximum Seamer speeds are calculated during the design of the Seamer. Calculations for a maximum production speed include "Under Load" situations. Many components in the Seamer are designed knowing that they will be under a load or running cans. Therefore, running any Seamer without cans, at high speeds, may cause extensive or abnormal wear and decrease the life of the Seamer. Seamers equipped with Two Speed Motors or AC Inverters have Auto- Speed Change Logic programmed in to slow the Seamer down to half speed when the can supply to the filler is stopped. The can line sensor then automatically increases the Seamer speed after cans are supplied at a rate fast enough to keep up with the Seamers mode of operation. Can line sensors should be wired into circuits already programmed and available to slow down the Seamer when there is an absence of cans. ANGELUS SANITARY CAN MACHINE COMPANY

5 SERVICE NOTICE 4900 PACIFIC BLVD., LOS ANGELES, CALIFORNIA TELEPHONE FAX NO /7/99-ALL00004A Recommended Seamer Shut Down and Storage Procedures for All Angelus Seamers Angelus recommendations for Seamer shut down are as follows; Any time a Seamer is shut down for *non-emergency reasons (breaks, meals, or shift changes), it is important to run and clear out all empty or product filled cans that remain within the Seamer Turret area. Cans left in the Seamer during shut down periods, especially long periods of time, will not meet strict quality standards when they are finally run through at start-up. This is important in can closing applications where Steam or CO 2 Gas is injected into the can for head space control. Steam Vacuum Seamers require a warm-up or start-up period before running product to insure consistent head space control. Seamers that inject CO 2 Gas to control head space regulate the pressure and volume of gas for Seamer production speeds. Start-up of Seamers with cans left in the Turret area are also subject to numerous can seam defects. Defects result from can misalignment at the makeup area or cans half seamed in the 1st or 2nd Operation Seam cycle. Seam defects could range from knockdown can flanges, cover and can misalignment or mismatch, dead heads, skidders, jumped seams, and more. Seaming Chucks, Seaming Rolls and all related components directly involved in the seaming process are subjected to abnormal pressure and wear under these circumstances that will ultimately decrease the production life expected from them. Recommendations for Storing the Seamer. In the event a new Seamer is stored prior to installation it is suggested to keep the Seamer as level as possible on the existing skid. Access to the Seamer inside the crate is suggested. Rotation of the Seamer using the Handwheel should take place at least once a week to rotate Bearings within the Seamer. Storage of existing Seamers should be as follows. Thoroughly clean the Seamer of all product and contaminates. Completely lubricate the Seamer, especially Seaming Rolls to force out any water that may have gathered during the wash down. It is suggested to use a rust preventive solution on all bare surfaces subjected to oxidation. Leave the Seamer completely covered and still allow access for weekly rotation of the Seamer. This suggested weekly rotation helps to keep bearings from flattening and oxidation from building up. It is desirable to run the machine under power for 10 to 15 minutes. Always store the Seamer in a dry atmosphere away from as much humidity as possible. Never leave the Seamer on open shipping docks, platforms or outside the building exposing it to the weather. Our recommendations are in the interest of maintaining consistent quality and product integrity produced by all Angelus Seamers. * Emergency Seamer shut downs are usually a result of can jams that require clearing the Seamer of cans in the Turret area. Angelus Sanitary Can Machine Company

6 Revised Knockout Pad Adjustment Procedures SERVICE NOTICE 5/23/96-ALL00005 Angelus Umbrella style Knockout Pads are designed to provide additional clearance for Pull Tabs when covers crown or dome from internal pressure during the seaming cycle. Knockout Pad numbers 52L841 = 206 diameter covers 53L841 = 204 diameter covers 54L841 = 202 diameter covers Seamer Models with these Knockout Cam numbers 62H = 26H L = 57L S = 3S S = 16S820/202MS - 17S820/204+ Adjusting Umbrella style Knockout Pads 1st. Insure that the Lower Chuck Cam is located correctly, the Lower Chuck Plate plane is within tolerance and the Seamer Pin Height is correct. 2nd Measure the countersink depth on several covers. Example:.270 3rd Measure the Knockout Pad contact area of the cover on the same set of covers. Average these dimensions. Example:.155 Cover Countersink depth measured with a Countersink Gauge Using a Countersink Gauge to measure the Pad contact area. Knockout Pad contact area of the Umbrella style Pad Angelus Sanitary Can Machine Company 1 of 2

7 SERVICE NOTICE 4th. Subtract the Pad contact dimension,.155 from the countersink dimension,.270 Equals:.115 5th. Measure and add the Knockout Pad Offset depth.160 of an inch to the above result. Equals:.275 6th. Add.080 of an inch to the above result in step 5. 5/23/96-ALL00005 Equals:.355 of an inch 7th. Add.355 to the Seamer Pin Height. Example: = Knockout Pad Offset measurement equals.160 of an inch 8th 9th NOTE: Place each station at the Timing Pin located on the Lower Turret Guard. Adjust the Knockout Pad height at all stations to obtain inches from the offset area of the Pad down to the Lower Chuck Plate. Secure 1/2-20 Jam Nuts securely. Adjust the Discharge side of the Knockout Cam radially. Rotate the Seaming Turret around, with a seamed can and correct internal pressure, and Adjust Knockout Pad height stop at the point where the seamed can has with an Inside Micrometer. just released from the Seaming Chuck. Position the Knockout Cam-Discharge radially until a.010 feeler gauge slips between the can and Lower Chuck Plate. Secure the Cam. Set Knockout Pads measuring from Lower Chuck Plate up to the Offset area of the Pad. Set Knockout Pad height when each station is positioned at the Timing Pin located on the Lower Turret Guard. Check can and cover control during the rise up to the Seaming Chuck. When the cam is adjusted correctly, one should not be able to lift the can and cover up away from the Lower Chuck Plate during the entire duration or cam rise, but still be able to turn the can freely without any binding or pressure from above. Angelus Sanitary Can Machine Company 2 of 2

8 SERVICE NOTICE 9/8/04-ALL00006B Seaming Rolls with Ceramic Ball Bearings *Endplay Adjustment Procedure. 1. Clamp a Seaming Roll Pin in a Seaming Roll Lever mounted in a vise. 2. Place the Seaming Roll Seal Shield onto the Pin, aligning pin notch with shield tab. (pin notch and shield tab on "L" style rolls only) 3. Install 292L616 Shim Washer, used to cover Pin notch in order to retain grease. (this washer is for the "L" Roll assemblies only). Pin secured in Lever, Shield installed and Shim Washer placed over the Pin 4. Install both the Oil Seal and Retaining Seal. Retaining and Oil Seals installed 5. Install the Ceramic Ball Bearing Inner Race assembly. 6. Install Snap Ring and Shims; Shims Average (.043 'L' Rolls or.010 'S' Rolls) 49L617 Snap Ring for 60L, 62H, & 121L 28S853 Snap Ring for 140S & 180S 362L616 Shims for 60L, 62H, &121L 75S816 Shims for 140S & 180S *All Seaming Roll Assemblies using the ceramic ball bearings will be adjusted with the proper endplay before leaving Angelus. ANGELUS SANITARY CAN MACHINE COMPANY 1st Ball Bearing and nominal.043" th. of Shims with Snap Ring 49L617 for preliminary setup. 1 of 3

9 SERVICE NOTICE 9/8/04-ALL00006B 7. Install the other Ball Bearing Inner Race, Seaming Roll Retainer and Seaming Roll Retainer Screw. Torque Retainer Screw to 14.5 ft. lbs. If the Seaming Roll starts to bind during clamping process, stop tightening. Add shims in increments of.001 or less to obtain free spinning Roll. 8. Spin the Seaming Roll. If there is any resistance at all, it will be felt and the Roll will come to a stop after a couple of revolutions. If no resistance is felt and the Roll spins freely, go to step no When endplay is reached through adding Shims, the Roll will spin freely without resistance. Remember, these are Ball Bearings and do not require seating in cups like the Timken Tapered Roller Bearings. 10. Mount a dial indicator on the Seaming Roll Lever surface and place the needle on the Rolls top surface. Dial Indicator position on the Roll. 11. Carefully rock the Seaming Roll back & forth to check endplay in the assembly. Add or remove Shims until freeplay reads / inches. This tolerance is not to be exceeded. continued next page; Checking freeplay with a dial indicator. ANGELUS SANITARY CAN MACHINE COMPANY 2 of 3

10 SERVICE NOTICE 9/8/04-ALL00006B ASSEMBLY NOTE: There will be a slight rocking action in the Roll when tipped back and forth by hand. This can be measured with the dial indicator postioned on the groove profile of the Roll. Shims should be adjusted until rocking action reads / inches. This tolerance is not to be exceeded. Checking angular play or rocking in bearings. 12. When satisfied with endplay, install the Bottom Closure and Snap Ring. LUBRICATION REQUIREMENTS: Ceramic Ball Bearings assembled within the Seaming Roll and mounted ready for production, should only require; With new Seaming Roll Pin 5 shots of N.L.G.I. Type O grease from a hand grease gun for each assembly. With used Seaming Roll Pin 2 shots of N.L.G.I. Type O grease from a hand grease gun for each assembly. Thereafter, if more than 1 shot of grease is installed, the ceramic ball bearing assembly will expel excess grease out of the assembly. Suggested Lubrication Intervals Every 72 Hours with N.L.G.I. Type O grease or 1 shot after sanitation to remove water from Seaming Roll. ANGELUS SANITARY CAN MACHINE COMPANY 3 of 3

11 SERVICE NOTICE 5/22/09 -ALL00008B PAINT TOUCHUP All Pneumatic Scale Angelus Seamers Finished with the *2.8 VOC Polyurethane Enamel Paint AUE-280 with HSP /2.8 VOC Tintable Polyurethane Primer Touchup or Repaint Procedures NOTE: These procedures must be followed to successfully complete touchups. Follow the next few steps to prepare the surface. 1. Clean the surface with a degreaser. 2. Sandblast, power sand or hand sand the area (80 grit). Sandblasting is required when painting other than touch-up. Old enamels or epoxy paints must be removed from the surface before this paint can be applied. 3. Clean the area with Metal Prep #79 then Actone. 4. Use an Ultraviolet lamp to check for oil contamination. This is very important. Contamination will be a blue or blue-green color sometimes florescent under the light. 5. Wipe down the area with Actone just before painting. Spray Gun requirements; The following is a list of Spray Guns suggested by Pneumatic Scale Angelus and the paint manufacturer a. **Binks Mach 1 HVLP Spray Gun with, Binks #905VT Carbide Fluid Nozzle having a.088 of an inch (2.23mm) orifice. Binks #905VT Carbide Tip Fluid Needle Binks #905P Air Nozzle NOTE: NOTE: Cup or tank size requirements are dependent on the amount of painting to be done. A 2 gallon pressure tank is normally used. When there are smaller jobs, use 1-qt. Cup gun or Cub touch-up gun. (See Fig. #1 pg. 2 and Fig. #2 pg. 3) The Fluid Hose should not extend 10 feet in length. The Air Hose from the Pressure Pot to the Spray Gun should be 9 ft. 8 in. in length. The 3/8 air hose to the Two Gallon Pressure Pot should not exceed 25 feet in length. Do not use quick disconnect fittings to connect lines to the Two Gallon Pressure Pot or Spray Gun. Quick disconnect fittings are too restrictive. b. **Binks Mach 1 Cub HVLP Gravity Feed Touch-up Gun with, Binks #905VT Carbide Fluid Nozzle having a.088 of an inch (2,23mm) orifice. (See Fig. #3 page 3) * PPG Industries, Inc One PPG Place, Pittsburgh, PA (USA), Phone: (412) ** Binks (US Corporate Offices) ITW Industrial Finishing 195 Internationale Blvd. Glendale Heights, IL (630) or 1(877) PSAngelus 4900 Pacific Blvd. Los Angeles, CA Tel: (323)

12 SERVICE NOTICE 5/22/09 -ALL00008B Fig. #1 Binks Mach 1 HVLP Spray Gun 1 = Lightweight Air Nozzle 2 = Fluid Inlet 3/8 NPS (m) 3 = Extra smooth trigger action 4 = S.S. Fluid Nozzle & Needle 5 = Side Port Control 6 = Fluid Control 7 = Forged Aluminum Body 8 = Air Inlet 1/4 NPS (m) Binks Model (2 qt.) Pressure Type Agitator Cup Assembly. 2-4 PSAngelus 4900 Pacific Blvd. Los Angeles, CA Tel: (323)

13 SERVICE NOTICE 5/22/09 -ALL00008B Fig. #2 Two Gallon Pressure Pot used with the Mach 1 HVLP Spray Gun. Fig. #3 Binks Mach 1 Cub HVLP Gravity Feed Touch-up Gun 1 = Lightweight Air Nozzle 2 = Fluid Inlet 3 = Air Inlet 1/4 NPS (m) 4 = Fluid Control 5 = Fan Control 6 = Forged Aluminum Body 7 = Fluid Cup PSAngelus 4900 Pacific Blvd. Los Angeles, CA Tel: (323)

14 SERVICE NOTICE 5/22/09 -ALL00008B Follow the next few steps to apply the paint, 6. Follow paint mixing instructions according to Product Data Sheets. 7. If you are using the Air Brush (Touch-up Gravity Feed Gun), you must continually shake the filled Pot immediately prior to application. It may be helpful to place a couple of 3/4 inch steel balls in the Fluid Cup. These will help in keeping the paint mixed properly during agitation. NOTES: When applying coats between Primer (HSP-2128) allow 10 minutes drying time between coats. When applying coats between Paint (AUE-280) allow 10 minutes drying time between coats. Allow Primer (HSP-2128) at least 1 hour to dry before applying Paint (AUE-280). 4-4 PSAngelus 4900 Pacific Blvd. Los Angeles, CA Tel: (323)

15 Service Notice ALL00009B - 6/14/07 Adhesive-Sealants- Seal Lubricants USAGE Clean all surfaces CLEANER #7070 LOCTITE PRIMER "N" #7649 and #620 GREEN RETAINING COMPOUND Used on 81L, 101L, 121L & 62H Seaming Spindle Drive Gear Bearing. 1. Use Primer 'N' on stainless material. Note: Let Primer evaporate completely or wipe dry with a clean rag before applying Loctite. 2. Apply Loctite #620 to both inner & outer bearings races before assembly. 3. Allow 2 hours fixture time before turning turrets over. Use on press/fits primarily for repair of bearing mounting surfaces. 1. For maximum strength Loctite #620 will be used with Loctite #7649 Primer N. The Loctite should be applied to the sleeve and the primer to the mating surface. LOCTITE #272 RED THREADLOCKER Used on all other bearing assembly work or where specified. For maximum strength Loctite #272 will be used with Loctite #7649 Primer N. The Loctite should be applied to the bearing race and the primer applied to the mating surface. Note: Let Primer evaporate completely or wipe dry with a clean ragbefore applying Loctite. LOCTITE #243 BLUE THREADLOCKER Used on all fasteners. Loctite #243 can be used without primer in cast iron parts. In stainless steel parts Loctite #7649 Primer N should be applied to fastener to obtain full cure of the Loctite. Apply Primer 'N' and Loctite #243 Blue to threads. Angelus 4900 Pacific Blvd. Los Angeles, CA Tel: (323) /4

16 Service Notice ALL00009B - 6/14/07 PERMATEX "NO MORE LEAKS" Used on all plastic fittings or plastic material in place of PST Sealant Plastic to plastic or plastic to metal applications are acceptable applications. LOCTITE #2 Gasket Sealant (Non hardening pliable sealant) Used mainly on overhaul seamers for improved sealing. LOCTITE #567 THREAD SEALANT Used on all stainless steel and other metal fittings. PERMATEX (#80017) Aviation Form-A-Gasket #3 Sealant Used as a sealant between castings or on threads that protrude into oil and grease resevoirs. Used also on lower turret guard. LOCTITE #1 Gasket Sealant (Fast dryinghard setting) Used on 'P' Seamers - Fills the top counterbore in base covering the 3P464 intermediate stud assembly. LOCTITE Superflex Blue RTV - Silicone Adhesive Sealant Used on the bottom of base mounted enclosures and housing service cover seals. Angelus 4900 Pacific Blvd. Los Angeles, CA Tel: (323) /4

17 Service Notice ALL00009B - 6/14/07 LOCTITE 573 Flange Sealant Use Loctite 573 for base mounted top plates. Sold as Angelus Part #24M226. This is a anaerobic slow drying sealant. The cure can be expedited by using Loctite 7649 primer. Parker Super O Lube Used as a o-ring and seal lubricant during assembly. LOCTITE Food Grade Anti-seez Use Loctite (FG) lubricant on all threaded connections to lubricate, seal, prevent galling, and high friction. Effective on stainless steel. Use also as a lubricant on machine parts, press fits, shafts, etc. Do not apply to fittings. Angelus 4900 Pacific Blvd. Los Angeles, CA Tel: (323) /4

18 Service Notice ALL00009B - 6/14/07 LOCTITE GLUE USAGE USE THE FOLLOWING GUIDELINES DURING ASSEMBLY PROCEDURES; LOCTITE #404 USE FOR JOINING O-RINGS AND V-RINGS. 1. Use the O-Ring Splicing Kit for O-Ring joinery. 2. Bond the joint with the Instant Adhesive and fixture. 3. Clean the joint with the Clean Up Solvent. Step 1 Step 2 4. Use the Water Proofing Solution over the joined material. Water Proofing Solution protects the joint against moisture. Step 3 Step 4 LOCTITE BLACK MAX GEL USE FOR ADHERING RUBBER TO METAL. LOCTITE #495 SUPER BONDER USE FOR ADHERING SPONGE TYPERUBBER (EPDM)TOGETHER. LOCTITE #454 SURFACE INSENSITIVE INSTANT ADHESIVE GEL USE FOR ADHERING SPLICED 140S/180S UPPER TURRET HUB SEALS TOGETHER. Angelus 4900 Pacific Blvd. Los Angeles, CA Tel: (323) /4

19 Service Notice All /28/04 Subject: Maximum heights from face of base to the lower face of upper turret housing. Purpose: Provide maximum machine height without disengagement of the elevator screw from the column bushing for maintenance. Maximum Heights 60L Seamer 25 /635mm Bottom face of drive case support 62H Seamer 24-3/4 /628.65mm L Seamer 27 /685.8mm 140S Seamer 27 /685.8mm 41L 25 Bottom face of top plate support 40L 28-3/4 Bottom face of top plate support Note: When a stainless steel base top plate is installed measure from the top of it. 180S Seamer 26 /660.4mm Angelus 4900 Pacific Blvd. Los Angeles, CA Tel: (323) /1

20 Service Notice All00011A-7/14/04 Seamer Exchange Audit Customer: Service Rep: Location: Date: Existing Machine Serial # Exchange Machine Serial # 60L 61H 62H 120L 121L 140S 180S 60L 61H 62H 120L 121L 140S 180S Product Run: Product Run: CPM: Tin Line Hgt: CIP Sys: CPM: Tin Line Hgt: CIP Sys: Discharge Conveyor: Angelus Other Discharge Discharge Conveyor: Angelus Other Discharge Enclosure: Safe Dr Interlock Mach Mnt Floor Mnt Enclosure: Safe Dr Interlock Mach Mnt Floor Mnt Tooling Condition: Change Part Sizes: Tooling Condition: Change Part Sizes: Separator: Separator: Spec Cover Feed Chute: Filler Info: Filler Model Feed Chain Gear Drive Belt Drive Spec Cover Feed Chute: Filler Info: Filler Model Feed Chain Gear Drive Belt Drive CO2 Controls: Grease Lubricator: CO2 Controls: Grease Lubricator: Lubrication Manuf:Oil Grease Lubrication Manuf:Oil Grease Motor Drive:Vari-Speed Fixed Power Horsepower Frame Size Comments; Motor Drive:Vari-Speed Fixed Power Horsepower Frame Size Comments; Angelus 4900 Pacific Blvd. Los Angeles, CA Tel: (323) /1

21 Service Notice All /6/04 Return Parts Authorization Form In order to expedite evaluation of return parts please complete form. Company: Location: Name: Date: Machine Model: Serial Number: Part Numbers being returned (include quanities): Length of time parts were in service: Return Authorization Number: Customer comments on reason for return: Service Dept. Disposition: By: Date: Angelus 4900 Pacific Blvd. Los Angeles, CA Tel: (323) /1

22 Service Notice All /5/04 Subject: Adjustable Round Bar Can Transfer Table Purpose: An improved concept for transporting cans from the filler to the seamer with less agitation and spill is now available from Angelus. The Adjustable Round Bar Can Transfer Table is manufactured from high-grade corrosion resistant stainless steel that is hard chrome plated to provide less friction and metallic pickup. The round bar design is easily adjustable for both height and wear and can be used in a variety of beverage and food applications. The Adjustable Round Bar Can Transfer Table is available as an option on new equipment or as a modification for existing Angelus can seamers equipped with a fabricated can feed extension table. Benefits: Smooth transfer of can between filler and seamer provides less can agitation and product spill Quick and easy adjustment for both height and wear Extends table wear life up to ten times longer than typical flat wear plate tables Reduces requirement for expensive soap solutions for lubrication High-grade corrosion resistant stainless steel round bars are hard chrome plated to provide less friction and enhance can mobility Enhances machine's performance, reduces downtime, and increases productivity Direct replacement on many Angelus model Seamers Enhanced Productivity Beverage processors have given the Angelus Round Bar Can Transfer Table rave reviews. It has significantly improved their process and productivity by enhancing can mobility and reducing product agitation and spillage between the filler and seamer. Because there are only four-points contacting the bottom of the can the amount of friction and drag has been significantly reduced, thereby reducing the requirement for expensive lubricating soap solution. Extended Wear Life The wear life of the hard chrome plated corrosion resistant stainless steel Adjustable Round Bar Can Transfer Table provides a significant improvement over typical flat wear plate transfer tables. The Angelus design employs a support plate and clamp feature that provides for vertical height adjustment and allows the processor to simply and quickly rotate the bars to a new wear surface enhancing the life of the Round Bar Can Transfer Table up to ten times longer than typical flat wear plate transfer tables. Height Adjust Screw Turn Rollers Screw Angelus 4900 Pacific Blvd. Los Angeles, CA Tel: (323) /1

23 SERVICE NOTICE 8/29/96 all14001 Seamer Lubrication Checks Seamers that have been overhauled, either completely or partially, must have a thorough inspection of all lubrication devices to insure that the Seamer operates properly. OIL Lubrication; Seamers equipped with Automatic Lubrication devices (7 Feed Manzel Lubricators, Hydro- Tech Oil Pumps, or Interlube Systems) distribute lubricants through tubing, injectors, hoses or oil ports. The final destination of oil into the Seamer, no matter where this might be, must be checked to ensure that oil is being dispursed as designed and calculated. Fail Safe devices are installed where injectors or Divider blocks are used. Operation of fail Safe devices must be checked for proper operation. 121L and 62H Seamers with 7 Feed Manzel Lubricators do not have devices to detect a blockage or improper oil flow. Therefore, visual inspection must be performed starting from the Manzel Lubricator pump adjustments to all seven discharge points to insure that the proper amount of oil is lubricating running parts of these machines. GREASE Lubrication; All remote grease fittings or centralized grease lubrication points must be pointed out to the customer. All lines and grease discharge points should be visually verified to insure that all points are getting proper lubrication. Failure to inspect lubrication points throughout the Seamer may ultimately result in serious mechanical breakdown. Check the Instruction section of the Seamer Parts List for Lubrication adjustments and fitting locations for each Model Seamer. Angelus Sanitary Can Machine Company 1

24 Service Notice All 14002A - 07/06/11 SOAP SOLUTION FOR CAN LUBRICATION Suggested Dispensing Locations: Separate Nozzles should be placed at the Filler Pads or Plates, just before empty cans enter the Filler, Filler Can Feed Star Wear Plates and the Seamer Can Feed Extension Wear Plate. A separate soap dispensing unit should be installed exclusively for the Seamer/Filler area to provide higher concentration of mixture for un-seamed can transfer. General Considerations: Proper can lubrication is essential for empty can conveyor, filler in-feed, can transfer table (can feed extension) between Filler and Seamer, Seamer Lower Chuck Plates, and Seamer Discharge Conveyor. There are many factors contribute to the selection of the soap lubricants (soap) that make a great difference of the production efficiency and the product quality. The main considerations of the soap selection are lubricity, cleanness, water hardness, and cost. Beside the main consideration factors, there are also other consideration like food grade, chemical composition, biodegradable, additional additives, degree of foaming, surface tension, and many other considerations for unique applications. Consult with soap suppliers to verify what the best product/mixture for each unique application. In order for soap to work successfully, the "drop off" between the transitions must be properly adjusted, and Seamer needs to be setup within the specifications. Soap will not compensate the excessive backlash or worn out parts in Seamers. A good maintenance program combine with the proper soap solution will achieve a high efficiency production line and produce reliable product. Lubricity: Lubricity is the most important factor for the soap selection. The type of soap used must be able to provide the sufficient lubrication between the cans and the riding surfaces. Any soap which was not able to achieve the low friction should not be considered no matter how attractive the other factors might be. There are few elements that will affect the lubricity of the soap. The type of can bottom coating, bottom coating condition, material for cans, riding surface material, product in the cans, filled temperature, and more. The formulation and the thickness of lacquered coating is the most significant factor amount all. A low friction coating could allow use less amount of soap. A heavier and harder coating could prevent the coating wear off during the transport and exposing the bare substrate. If the empty can conveyor is continuously running when the can stop is closed, the conveyor chain will rub off the coating. In this case, the soap solution amount or mixture needs to be increased. Occasionally, the substrate of cans could be exposed due to the wear off or imperfection of coating. In this case, aluminum cans will require heavier mixture than steel cans, and the plastic containers, depending the polymer used, could be the worst. PSAngelus Cuyahoga Falls, OH, Tel: (330) ;Los Angeles, CA, Tel: (323) ; Clearwater, FL, Tel: (727) ; Belgium, Tel: ; U.K. Tel: ; Dreieich, Germany, Tel: ; Hong Kong, Tel: /2

25 Cleanness: Service Notice All 14002A - 07/06/11 Some soap might cause staining when it is used with a certain product, and some soap might form sludge with product or hard water. Depending on cleaning/maintenance procedure and schedule, selecting soap that produces less build up is always a plus. Water Hardness: In general, soft water (less than 1 grains/gallon or 17.1 mg/l) should be used for mixing soap solution. This will optimize performance and minimize soap usage. Cost: The cost of soap alone might be a major consideration when choosing the type of soap. However, the complete business model needs to be reviewed for the final cost of the soap. Consider additional cost incurred due to using improper soap for the application like slower running speed, can damage, and premature wear of parts could impact total cost of operation. Suggested Soap Lubricants: With the available soap products on the market today, the Fatty Acid base soap seems to work best for all type of cans. Soaps used for PET bottles do not provide sufficient lubricity for can applications. The following is a list of chemical compositions most often seen in soap. Consult with your soap supplier with your specific application for soap available in your area. Chemical Composition Application H 2 O Hardness Mixture * Fatty Acid Brewery Beverage Food Soft 1.00% Fatty Acid w/ Surfactant Brewery Soft 1.00% Amine Acetate Beverage Food Medium 1.00% Phosphate Ester Not Recommended Soft N/A * Mixture suggested is for can bottom coating in good condition. If the substrate were exposed, the higher percentage of mixture will be required. 2/2 PSAngelus Cuyahoga Falls, OH, Tel: (330) ;Los Angeles, CA, Tel: (323) ; Clearwater, FL, Tel: (727) ; Belgium, Tel: ; U.K. Tel: ; Dreieich, Germany, Tel: ; Hong Kong, Tel:

26 SERVICE NOTICES Check Valve and TD Flow Sensor Retrofit Kit 4/15/09-ALL14003A Follow Manufacturers instructions for installation and startup of the new assembly. HYDRA-TECH HYDRAULICS, INC. INSTALLATION INSTRUCTIONS (use sketch on page 3) CHECK VALVE AND TD FLOW SENSOR RETROFIT KIT 29H614AAAY5 Overview: Installation of this kit will allow operators of the HC211-ASC filtration system (PSAngelus Part # F029H614AAAY5) to eliminate the inlet wye strainer and the vane type flow sensor, both of which are prone to fouling with debris. An additional benefit is the further reduction of initial resistance on the pump which will increase its ability to pump properly at lower temperatures and to operate with higher viscosity oils. The check valve acts to prevent the pump from siphoning dry when the filter is shut off and provides positive lubrication during the initial start-up of the filter system. The kit consists of three subassemblies; an inlet assembly with the check valve, a valve train assembly with the flow switch, and a hose kit for fabricating the proper length of inlet hose. Sometimes the hose assembly and 1/2" hex nipple are not required depending on the version of your filter system. Installation Procedure 1. Turn the filtration system off and allow all pressure to dissipate. Close the small ball valve located between the left hand canister and the solenoid valve, then disconnect the QDC connector at the top of the oil inlet line on the left hand canister. 2. Remove the inlet hose from between the interior bulkhead fitting and the suction strainer inlet. Set it aside for reuse or as a measuring aid later. 3. Remove the inlet strainer along with the hose fitting on its end. There should be a male thread fitting to thread the checkvalve onto. You may install the hex nipple to provide the required male thread. The checkvalve may face either forward or to the left side depending on your version of the filter and your preference. 4. Unplug the connecting cords from the pressure switches and unscrew the switches from the valve train. Mark each switch so that they can be installed in the proper (upstream/ downstream) order. 5. Open the electrical junction box and disconnect the existing flow switch leads from connectors 10, 11 & 12. continued next page; PNEUMATIC SCALE ANGELUS 1 OF 3

27 SERVICE NOTICES 4/15/09-ALL14003A IMPORTANT: The FT switch works only with 12-24V DC power, Do not use AC power. 6. Remove the conduit connector and flex from the junction box. 7. Disconnect the oil line from the end of the valve train by unscrewing the female hose fitting. 8. Break loose the pipe union and remove the entire valve train from the unit. Remove the unions male pipe fitting from the existing valve train elbow and reinstall it in the new valve train. 9. Reattach the new valve train to the pump outlet union. 10. Screw the outlet hose onto the provided fitting at the end of the valve train. 11. Install the 901 cord grip and sensor cable into the existing hole of the junction box and put the cover back on the junction box. The proper wiring scheme is: Terminal NOTE: #10. RED DC #11. BLACK DC + #12. WHITE NO The flow sensor has been properly installed into its fitting and calibrated at our plant. Do not adjust (tighten or loosen) flow switch or turn the switch adjustment screw without contacting our technical department first. 12. Install both pressure switches to their original positions. Reconnect the switch cords. 13. Crack open the bleed cock on top of the Hydro-Fil (right hand) canister. Open the ball valve closed in step 1. and reconnect the QDC connector. 14. Crack open the bleed cock located at the pump outlet (just below temperature gauge) to bleed off any entrained air. If the pump has a hard time priming during the initial start-up we recommend that you open the check valve (remove the top cover) and squirt oil into the valve until it is full. Put the cover back on and restart the pump. Once the pump is primed the checkvalve will maintain sufficient oil in the system to prevent air locking in the future. 15. Monitor the open bleed cock on the Hydro-Fil canister until the air has been purged from the system. Check the system for leaks before closing the cabinet. SEE SKETCH ON THE NEXT PAGE. PNEUMATIC SCALE ANGELUS 2 OF 3

28 SERVICE NOTICES 4/15/09-ALL14003A PNEUMATIC SCALE ANGELUS 3 OF 3

29 SERVICE NOTICE 9/11/96-ALL14004 TRABON OIL PUMP FILTER 5L414 MODELS 81L, 101L, 121L, 140S and 180S PERIODIC MAINTENANCE Function: Line Filter 5L414 is installed on the output side of oil pumps used on the Seamers. Its function is to trap particles or contaminates that may have been deposited in the Oil Reservoir of the pump. This filter is an important component of the lubrication system. It provides added protection against contamination reaching Master or Sub-Divider Blocks dispersing oil throughout the Seamer. Typical Filter installation on the output side of the Pump. Description: Line Filter 5L414 is manufactured by Lubriquip Corp. and supplied with all Seamers equipped with the Trabon Oil Pump Systems. Its basic design is comprised of a size 25 micron filter ( inch particle), spring retainer, spring and end plug with o-ring seal. Maintenance: Filter *replacement should be after a pressure increase is noticed at the Trabon Oil Pump other than normal running pressure. A pressure increase is an indication that the Filter has been clogged. Further maintenance may require cleaning the Pump Reservoir if this symptom persists. If the Filter is clean and a pressure increase is still noticed, check output lines beyond the Filter. PUMP COMPONENTS Housing End Plug w/o-ring 25 micron Filter Spring Spring Retainer *Cleaning the Filter Element with solvents or other cleaning agents is not recommended.

30 Service Notice All14005N-01/17/12 Seamer Lubrication Suggestions, Requirements & Specifications By Pneumatic Scale Angelus CAUTION: Contact your lubricant suppliers to verify the compatibility of lubricant with paints and components on the seamer before use. Some additives and base oil may affect stability of internal & external coatings resulting severe machine internal damage. PSAngelus Cuyahoga Falls, OH, Tel: (330) ;Los Angeles, CA, Tel: (323) ; 1/6 Clearwater, FL, Tel: (727) ; Belgium, Tel: ; U.K. Tel: ; Dreieich, Germany, Tel: ; Hong Kong, Tel:

31 Service Notice All14005N-01/17/12 PNEUMATIC SCALE SANGELUS SERVICE NOTICE LUBRICATION Appropriate Lubricants are essential to the longevity of the machine. Quality engineering is of no value if good maintenance practices are ignored or poor quality or improper lubricants are employed. Generally, good quality lubricants of the correct type will provide long, trouble-free service. In some cases, we recommend very specific products for successful operation. When oil circulation and filtration systems are used, monitoring oil integrity on a monthly basis is recommended. Oil change out on circulating systems should never exceed a six month period or two thousand hours of run time whichever comes first, unless specified & certified by lubricant suppliers. More and more companies are choosing to use food grade lubricants throughout their machines. Historically, food grade lubricants had shorter service life and poorer wear protection than regular petroleum lubricants. Improved additives and synthetic base oils have done much to overcome this shortfall. Paying close attention to maintenance practices and properly chosen lubricants are keys for trouble-free operation of your Pneumatic Scale Angelus Seamers. USDA eliminated their internal group that registered Non Food Compounds such as Lubricants H1 and H2 in They still have the responsibility for monitoring food and beverage plants to make sure they comply in the use of these lubricants. After several years of self certification by lubricant companies, NSF International was approved in 2001 as a 3rd party registrant for Non Food Compounds. NSF uses guidelines originally set up by USDA conforming to ingredients as specified by the FDA. As an equipment manufacturer, it is our responsibility to specify the lubricants that will meet the application requirements. Due to the high cost and the duration of time to put each lubricant through the test, Pneumatic Scale Angelus has no plan to test more lubricants in the near future. As specified in this document, users of Pneumatic Scale Angelus seamers may use lubricant that is equivalent or exceed the performance of the suggested lubricants listed on this document, and lubricant companies are responsible to guarantee the quality and performance of their products. If users decide to change out the lubricant, it is important to specify lubricant that is compatiable with the factory filled lubricants, or a complete flush/clean out the existing lubricant is necessary. Abbreviations of Industry Terms A.S.T.M. U.S.D.A. N.L.G.I. A.G.M.A. F.D.A. A.P.I. S.A.E. I.S.O. cst S.U.S. NSF American Society for Testing and Materials United States Department of Agriculture National Lubricating Grease Institute America Gear Manufacturers Association Food and Drug Administration American Petroleum Institute Society of Automotive Engineers International Organization for Standardization Centistokes Saybolt Universal Seconds National Sanitation Foundation International PSANGELUS Model P Seamers Seamer Grease Fittings unless otherwise noted Grease Grade 1 Drive Case EP Gear Lube 220 ** Lower Chuck Cam Area on Model 53P & 58P Seamers only EP Gear Lube 220 ** PSAngelus Cuyahoga Falls, OH, Tel: (330) ;Los Angeles, CA, Tel: (323) ; 2/6 Clearwater, FL, Tel: (727) ; Belgium, Tel: ; U.K. Tel: ; Dreieich, Germany, Tel: ; Hong Kong, Tel:

32 Service Notice All14005N-01/17/12 PSANGELUS Model 41L Seamers Manzel 7 Feed Lubricators, Interlube Systems, Trabon Oil Pump Systems, Oil Filtration and Recirculation Systems Special Seamer Oil 150 Drive and Gearcase Oil EP Gear Lube 220 ** Seaming Roll Grease Grease Grade 0, Grease Grade 1 * PSANGELUS Model 60L Seamers Grease for Lincoln Electroluber, Lower Chuck Bearings (24L616) Grease Grade 0 Seaming Roll Grease Grease Grade 0, Grease Grade 1 * Grease for all other Fittings Grease Grade 1 Drive Case Oil EP Gear Lube 220 ** In-Motion Timer EP Gear Lube 220 ** Can Feed Drive EP Gear Lube 460 ** Can Feed Chain Lubricator Chain Lube 100 PSANGELUS Models 61H/62H/63H/64H Seamers Manzel 7 Feed Lubricators, Interlube Systems, Trabon Oil Pump Systems, Oil Filtration and Recirculation Systems Special Seamer Oil 150 Seaming Roll Grease Grease Grade 0, Grease Grade 1 * Drive and Gearcase Oil EP Gear Lube 220 ** Filler Drive Gear Case EP Gear Lube 220 ** 61H Seamer Base Grease Grade 1 Can Feed Chain Lubricator Chain Lube 100 PSANGELUS Models 81L/101L/121L, 4M/5M/8M, 12M/12MH, 140S Seamers Manzel 7 Feed Lubricators (80,100,120L), Trabon Oil Pump Systems, Oil Filtration and Recirculation Systems Special Seamer Oil 150 Drive and Gearcase Oil (4M,5M,8M) Special Seamer Oil 150 Drive and Gearcase Oil (81L,101,121L, 12M/12MH, 140S) EP Gear Lube 220 ** Filler Drive Gear Case EP Gear Lube 220 ** Lincoln Electroluber or Hand Greasing Grease Grade 0 Seaming Roll Grease Grease Grade 0, Grease Grade 1 * Seamer Base (Utilizing Grease Injectors) (81L,101,121L) Grease Grade 1 Cone Drive (4M,5M,8M) EP Gear Lube 460 PSAngelus Cuyahoga Falls, OH, Tel: (330) ;Los Angeles, CA, Tel: (323) ; 3/6 Clearwater, FL, Tel: (727) ; Belgium, Tel: ; U.K. Tel: ; Dreieich, Germany, Tel: ; Hong Kong, Tel:

33 Service Notice All14005N-01/17/12 PSANGELUS Models 180S/181S Seamers Trabon Oil Pump Systems, Oil Filtration and Recirculation Systems Special Seamer Oil 150 Lincoln Electroluber or Hand Greasing Grease Grade 0 Seaming Roll Grease Grease Grade 0, Grease Grade 1 * Drive and Gearcase Oil EP Gear Lube 220 ** Filler Drive Gear Case EP Gear Lube 220 ** Optional Vari-Speed Inching Mechanism: Worm Gearhead Reducer... Speed Variator Hydraulic System... * NOTE: DO NOT use grade 1 grease on automatic seaming roll lubrication system. ** NOTE: Application could be substituted with Synthetic Seamer Oil 220. Lubricant Specifications and Manufacturers Caution: Contact your lubricant suppliers to verify the compatibility of lubricant with paints and components on the seamer before use. Some additives and base oil may effect stability of internal & external coatings resulting in severe machine internal damage. Lubricant Manufacturer Technical Support Web Sites: Shell Oil Company: Fuchs Cassida: Fuchs Lubritech: Total Lubricants: ChevronTexaco Oil Company: ExxonMobil: Swepco: Kluber Lubrication: EP Gear Lube 460 AW Hydraulic Oil 68 Special Seamer Lubricant 150 and Description: High quality paraffinic petroleum lubricating oil with ashless dispersant, rust and oxidation inhibited, anti-wear protection, non-foaming, extreme pressure protection, and emulsifier. Specifications: ISO Viscosity Grade Viscosity, 40 C 135 to to 242 Viscosity Index, Minimum Appearance Bright & Clear Bright & Clear Color, ASTM D-1500, typical Flash Point, COC, C, typical Manufacturers of H-2 rated products: Shell Oil Company Aeroshell Oil W 80 Aeroshell Oil W 100 Total Lubricants Seamer Oil 150 Seamer Oil 220 Manufacturers of H-1 (Foodgrade incidental contact) products: Fuchs Lubritech Cassida GLE 150 (synthetic) Cassida GLE 220 (synthetic) Fuchs Lubritech TLS 150 ChevronTexaco Oil Company PSAngelus Cuyahoga Falls, OH, Tel: (330) ;Los Angeles, CA, Tel: (323) ; 4/6 Clearwater, FL, Tel: (727) ; Belgium, Tel: ; U.K. Tel: ; Dreieich, Germany, Tel: ; Hong Kong, Tel: Chevron Seamer Oil FM

34 Service Notice All14005N-01/17/12 EP Gear Lube 220 and Description: High quality paraffinic petroleum lubricating oil with rust and oxidation inhibitors, extreme pressure additives, thermally stable, good demulsibility and anti-foam protection. Specifications: ISO Viscosity Grade AGMA Grade 5 EP 7EP - 7S Viscosity, 40 C 198 to to 506 Viscosity Index, Minimum Appearance Bright & Clear Bright & Clear Flash Point, COC, C, typical Rust Protection, ASTM D-665B Pass Pass Copper Strip Corrosion, ASTM D-130, Max. 1b 1b Manufacturers of H-2 rated products: Swepco Swepco 201 Gear ISO 220 Swepco 201 Gear ISO 460 Total Lubricants Carter EP 220 Carter EP 460 Shell Oil Company Omala Gear Oil 220 Omala Gear Oil 460 ExxonMobil Oil Company Mobilgear 630 Mobil One SHC 634 Manufacturers of H-1 (Foodgrade incidental contact) products: Kluber Lubrication Kluberoil 4 UH1 460N Chain Lube 100 Description: High quality petroleum lubricating oil with rust and oxidation inhibitors, thermally stable with tackiness additives. Specifications: ISO Viscosity Grade 100 AGMA Grade 3 Viscosity, 40 C 90 to 110 Appearance Bright & Clear Flash Point, COC, C, typical 260 Rust Protection, ASTM D-665B Stringiness Pass Observable Manufacturers: Total Lubricants GP- 150 Chain Lubricant Note: Chain Lube 100 applicable for use on Can Feed Extension Chain for Seamer Models 60L, 61H/62H/63H/64H, 80L/81L/100L/101L/120L/121L, 140S, 180S/181S, 12M/12MH, 4M/5M/8M PSAngelus Cuyahoga Falls, OH, Tel: (330) ;Los Angeles, CA, Tel: (323) ; 5/6 Clearwater, FL, Tel: (727) ; Belgium, Tel: ; U.K. Tel: ; Dreieich, Germany, Tel: ; Hong Kong, Tel:

35 Service Notice All14005N-01/17/12 Anti-Wear Hydraulic Oil 68 Description: High quality petroleum lubricating oil with anti-wear performance, rust and oxidation inhibitors, thermally stable, demulsible. Specifications: ISO Viscosity Grade 68 Viscosity, 40 C 61.2 to 74.8 Viscosity Index, Min. 95 Appearance Bright & Clear Flash Point, COC, C, typical 234 Rust Protection, ASTM D-665A Pass Manufacturers: Total Lubricants Azolla ZS 68 Shell Oil Company Tellus 68 ExxonMobil Oil DTE 26 Grease Grades 0 and Description: High performance grease with extreme pressure protection, high mechanical and thermal stability, oxidation and rust protection, highly water resistant and excellent corrosion protection. Specifications: NLGI Grade 0 1 Penetration, worked (ASTM D-217) to 340 Dropping Point, C, Min Thickener Type Base Oil Properties: Lithium complex, Aluminum Complex, or Polyurea Lithium complex, Aluminum Complex, or Polyurea ISO Viscosity Grade, Minimum Viscosity, 40 C, Minimum Viscosity Index, Minimum Flash Point, COC, C, typical Manufacturers: Non Foodgrade (old USDA H-2 rating) Total Lubricants Zeniplex EP 0 Zeniplex EP 1 ExxonMobil Oil Mobilith AW 0 Mobilith AW 1 Manufacturers: Foodgrade (old USDA H-1 rating) Kluber Lubrication Klubersynth UH ExxonMobil Oil Mobilgrease FM 101 Total Lubricants Nevastane HT/AW 0 Nevastane HT/AW 1 Fuchs Lubritech Cassida RLS-0 Cassida RLS-1 PSAngelus Cuyahoga Falls, OH, Tel: (330) ;Los Angeles, CA, Tel: (323) ; 6/6 Clearwater, FL, Tel: (727) ; Belgium, Tel: ; U.K. Tel: ; Dreieich, Germany, Tel: ; Hong Kong, Tel:

36 SERVICE NOTICE ALL /22/02 ANGELUS SEAMER OIL CHANGE PROCEDURE WITHOUT OVERHAUL Procedure for changing from an existing lubricant to different makes, types, or grades of lubricants. Note: This procedure is used only when the lubricant is to be changed without a machine overhaul or service being carried out. Step 1: For seamers equipped with enclosed base, remove drain plug from sump or base cover of seamer to drain oil from seamer base oil reservoir. For seamer equipped with filtration system, disconnect pump hose and drain oil (Fig. 1). Fig. 1: Pump Hose Connection Fig. 2: Typical Oil Filler Plug and Oil Level Plug Locations Step 2: Remove oil filler plug and oil drain plug from lower turret (Fig. 2) to drain oil in the lower turret. Fig. 3: Typical Upper Turret Drain Plug Location Step 3: Remove oil drain plug from upper turret (Fig. 3) to drain oil in the upper turret. ANGELUS SANITARY CAN MACHINE COMPANY 1/3

37 SERVICE NOTICE ALL /22/02 Step 4: If the seamer is fitted with a Hydra-Tech filtration system (Fig. 4), remove and replace the water removal element as a minimum. It is preferable that the particulate filter element is also removed and replaced at this stage, thus removing any existing lubricant from the filtration system. Particulate Water Fig. 4: Hydra-Tech Filtration System Fig. 5: Manzel Oil Lubrication Step 5: Remove drain plug in the lower left corner of Manzel unit situated on the top of the upper turret housing (Fig. 5). Step 6: Manually remove any pipework or hoses between Manzel unit and seamer lubrication points. Drain any lubricant in the pipe-work and flush through (pipe-work only) with new lubricant (See Note *). Step 7: If the seamer is equipped with Trabon oil pump (Fig. 6 or Fig. 7), drain the reservoir, refill line, and all lines between the pump and the main divider block. Reconnect lines and fill the Trabon pump reservoir with new lubricant. Run the pump until fresh oil appears from all drain ports. Fig. 6: Trabon Oil Pump Fig. 7: Trabon Oil Pump ANGELUS SANITARY CAN MACHINE COMPANY 2/3

38 SERVICE NOTICE ALL /22/02 Step 8: If possible, examine upper turret cavities and remove any residual lubricant or contamination using clean wipes of fibre free rags. Step 9: Replace all oil drain, filler and level plugs in seamer. Replace all lubricant pipe-work and hoses. Replace all filters and insure correctness of installation. Step 10: Refill machine with appropriate grade and quantity of new lubricant. (Note: Method of refilling may differ depending on machine type and presence of filtration system). Step 11: If the seamer is fitted with Hydra-Tech filtration system. Make sure the system pressure is within operating ranges, and all fittings are oil tight and secured. If the seamer is equipped with Manzel lubricator, hand crank the lubricator to prime the system. Step 12: Start machine in slow speed for fifteen minutes. Step 13: Check oil level through lower turret oil level glass or overfill plug depending on seamer models. If fitted, check oil level in Manzel unit, Hydra-Tech filtration system pressure gauges, and Trabon pump pressure and oil level. Step 14: If the machine is equipped with Hydra-Tech filtration system; and after twenty hours of continuous operation, oil sample should be taken before and after the filter. If unusual high pressure were observed, replace particulate filter element or water removal filter as needed. If the seamer operates on a total loss system, oil sampling should continue for a period of two months beyond removal of the previous lubricant. *Note: The flushing of the seamer is not recommended unless the machine is to be serviced or overhauled and the spindles are to be removed and thoroughly cleaned. This procedure is applied to prevent the contamination from various cavities being flushed into rotating parts. ANGELUS SANITARY CAN MACHINE COMPANY 3/3

39 SERVICE NOTICE 3/31/98-ALL15001 Model 41L, 62H, 81L, 101L, 121L, 140S and 180S Seamers. Lower Turret V-Ring Splice Procedures V-Ring replacement on an assembled machine can be performed by properly splicing it. The method for cutting and splicing a V-Ring is as follows. 1. Remove the old V-Ring. 2. Prepare the new V-Ring on the bench or flat surface. Cut the Ring at a 450 angle from the top right to the bottom left. 3. Wrap the cut V-Ring around the Lower Turret area against a flat surface. Cut the V-Ring on a 450 angle. See below. 4. Use Loctite Adhesive #404 to bond the edges evenly together. CAUTION: Do Not glue the Seal with it stretched out. It must be glued in a relaxed condition. 5. Hold edges together for a minimum of 30 seconds. Carefully Trim the Rotation of Turret Assembly rough edges. 6. Use Loctite Water Proofing Solution to cure and seal the glued area. 7. Reassemble the V-Ring Clamps and Shields. Always pregrease the V-Ring Seal before starting the machine. ANGELUS SANITARY CAN MACHINE COMPANY

40 SERVICE NOTICE Model 61H & 62H, 80L & 81L, 100L & 101L and 120L & 121L Seamers. Subject: Feed Turret Bearing 3/25/98-ALL16001 Description: The Feed Turret Bearing used on these Seamers is part number 59P916 and has a metal shield on one side. This shield must be left in place during assembly and installed with the shield facing downward when the Feed Turret is assembled in the machine. Therefore, when bench assembly takes place for the Feed Turret mount the Bearing as seen in the photo below. Bench assembly of the Ball Bearing will position the Shield as seen here. ANGELUS SANITARY CAN MACHINE COMPANY

41 Service Notice All16002A-6/19/03 *Force Indicator Cell Usage To check Lower Chuck Spring Pressure Procedure; 1. Align the station at the timing pin location, usually located down on the lower turret guard between seam setting plates. 2. Set the force indicator cell on the lower chuck plate. Insert the proper spacer for the can height. Adjust the micrometer thimble until it contacts the seaming chuck flange and just begins to show a load. (The force cell must be centered evenly on the seaming chuck and flat against the lower chuck plate) 3. Record the reading on the dial. Continue adjusting the micrometer thimble, with the loading wrench, until it reads.022 inches. Read the load level at this setting. If the load is not within specifications, unload the force indicator cell and remove it. 4. Remove three screws that secure the lower chuck plate. Insert a 3/8" hex. key into the lower chuck spring adjustment screw. Turn counterclockwise to decrease load and clockwise to increase the load. A full turn on the lower chuck spring adjustment screw will change spring pressure approximately 77 lbs. For 'P' model seamers. After removal of the lower chuck body, use spring adjusting wrench 45P216 to adjust screw 1P254. Turn counterclockwise to decrease load and clockwise to increase the load. A full turn on the lower chuck spring adjustment screw will change the pressure approximately 77 lbs. 5. Install the lower chuck plate and screws. 6. Place force indicator cell, with correct spacer into place, and recheck spring pressure or load, ie. repeat step 3. NOTE: Force Indicator Cell is available from Angelus under part number F 332L616 **Digital Spring Pressure Gauge is available under part number F 352L616 Micrometer Thimble Micrometer Dial *Used as an alternative to using the "Dillon Gauge" outlined in Service Manuals **Supply Seaming Chuck size and voltage installed. Angelus 4900 Pacific Blvd. Los Angeles, CA Tel: (323)

42 SERVICE NOTICE All Bearing Locknuts and Lockwashers used on all Seamers. 10/31/91-ALL16003 Before installing Bearing Locknuts and Lockwashers on any assembly, check the matchup of both pieces. The Lockwasher serration angle is bent to fit properly against the Locknut and should not have a gap as seen in the photo below. If this occurs, bend the serrations down until it seats flat against the Locknut. Improper Lockwasher seat against the Bearing Locknut ANGELUS SANITARY CAN MACHINE COMPANY

43 SERVICE NOTICE ALL /8/98 Seaming Cam Roll Assembly Procedure All 39L816 Ball Bearings used on Models 81L, 101L, 121L, 140S and 180S must be assembled with the Ball loading grooves toward the top. Press procedures require the use of Loctite #272 "Red" on the Pin and Bearing Inner Race. Bearings must be pressed on even with the top of the Pin and spaced by Washer 47L816. Loading grooves are located on the inner and outer race of the Ball Bearing. Example of a ball loading groove Seaming Cam Lever with Cam Rolls installed. Note the Ball Bearing loading grooves are assembly toward the top. ANGELUS SANITARY CAN MACHINE COMPANY 1 of 1

44 SERVICE NOTICE Dillon Force Gauge Usage; 10/22/98-ALL16005 Seaming Chuck Compression Screw Dillon Force Gauge Deflection Indicator Lower Chuck Plate 1. Position the Dillon Gauge between the Lower Chuck Plate and Seaming Chuck. Turn the Compression Screw until contact is made. Turn both Dials to zero. The deflection dial stem must be positioned against a solid base. 2. Turn the Compression Screw until the Deflection Indicator reads.021 or.030 of an inch, depending on deflection requirements. The Dillon Gauge will display Spring Poundage. 3. To change the pressure, release the Lock Nut. Use a 1/4" allen wrench to adjust the Spring Screw to increase or decrease pressure. NOTE: One full turn on Spring Screw will change the pressure approximately 75 to 100 lbs. depending on the Spring used. The thimble nut should be swept around in one full motion until the Deflection Indicator reaches required settings. See your Can Suppliers Data Sheet for can and cover specifications. Always recheck poundage by repeating steps 1 and 2 outlined earlier. Deflection Dial stem positioned against the Turret surface. ANGELUS SANITARY CAN MACHINE COMPANY

45 SERVICE NOTICE All16006A-2/1/05 Model 80L, 81L, 100L, 101L, 120L, 121L, 140S, & 180S Seamers Lower Chuck Return Cam Shim Procedure In order to maintain the proper clearance between Lower Chuck Return Cam Rolls and Return Cams on a horizontal plane, it may be necessary to utilize Shims. The tolerance level through the horizontal plane (level or flat area between discharge and makeup cams) should be adjusted to maintain between.006 and.008 of an inch clearance. Shims are available in.003,.005 and.010 thicknesses. Shim Stock 253L816 Shims - 80L thru 121L 22S416 Shims - 140S 221S816 Shims - 180S Horizontal Plane between Discharge and Makeup Return Cam slopes Use Shims to maintain between.006" and.008" clearance Angelus 4900 Pacific Blvd. Los Angeles, CA Tel: (323) /1

46 SERVICE NOTICE 7/12/99-ALL16007 Models 121L, 140S and 180S Seamers Modification; Seaming Cam Roller Assemblies Scope: Seaming Cam Roller Assemblies consist of the 39L816 Ball Bearings (2), 47L816 Washers (2) and 4L829 Roll Pin. A 121L Seamer will have 12 of these assemblies, one for each seaming station. Cam Follower 239L816 replaces the standard Cam Roller Assembly Change: Effective July of 1999, Angelus has made a change from the five part assembly to a one piece Cam Follower. This assembly incorporates Roller Bearings versus Ball Bearings. The separate 47L816 Washer that fits under the assembly, is eliminated and built into the new Follower. All future orders for the Five Part Cam Roller Assemblies will be replaced by this new Cam Follower. Use part number 239L816 when ordering replacements. The separate 47L816 Washer is now built into the 239L816 Cam Follower The New Cam 239L816 Follower is assembled as a single unit utilizing Roller Bearings. ANGELUS SANITARY CAN MACHINE COMPANY 1

47 SERVICE NOTICE 10/31/00-ALL16008 Lower Chuck Bearings: (1 Set 18L816 consists of (3) Bearings) Description: 18L816 Ball Bearings are used in every Lower Chuck Assembly on the 180S, 140S, 120L, 121L, 100L, 101L, 80L, 81L, 61H and 62H Seamers. They are assembled in sets of three, pressed onto the Lower Chuck Mandrel Bottom. Because of the angular contact design, assembly direction is important. Scope: SKF manufactured bearings have a noticeable difference in the ball cage, being brass, compared to those from other suppliers. Assembly: To help identify the proper mounting of these bearings, the Service Manual places the Mandrel on the press. The first bearing is pressed on Open Side up (thrust side down) and the other two Open Sides down. These bearings identified in two ways. Etchings on the outer race for mounting direction and what is commonly called the Open Side of the bearing. In order to keep everyone consistent in their assembly of these bearings, the Open Side of the Bearing is pointed out in the bottom photo. Etchings on the outer races for assembly direction. "V" must point up when mounted on Machine as shown Open Side ANGELUS SANITARY CAN MACHINE COMPANY Open Side Thrust Side 1

48 SERVICE NOTICE Lower Chuck Bearings: (1 Set 18L816 consists of (3) Bearings) 10/31/00-ALL L816 Ball Bearing ANGELUS SANITARY CAN MACHINE COMPANY 2

49 Service Notice All /28/03 Pertaining To: 140S & 180S Angelus Seamers/Seaming Spindle Lower Bearing Retainer Screws. Retainer Screws Upgrades/Changes: 1) When installing the Seaming Spindle Lower Bearing Retainer Screws, apply Loctite #243 (blue) to the screw threads. Example: 180S Seamer / 65S817 Bearing Retainer / (18) M x 20mm Socket Head Screws 2) When installing the Seaming Spindle Lower Bearing Retainer Screws torque each screw to 35-ft. lbs. Purpose: To prevent the possibility of damaging the Retainer Screw threaded hole and bore walls. Benefit: The application of Loctite #243 (blue) Thread Sealant provides additional sealing and locking properties to the Retainer Screws. A Torque Specification of 35-ft. lbs. maintains a safe maximum controlled tightness without damage to components. Angelus Sanitary Can Machine Company 1/1

50 ALL20001A-7/11/07 Seaming Cam Release Spring Adjustment Requirements SERVICE NOTICE Figure 1 On Seam The seaming cam release spring is designed to restrain the 2nd operation cam section during 1st operation seam checks. Figures 1 & 2 are examples of incorrectly adjusted release springs. In Figure 1 the release spring bolt has been improperly tightened resulting in abnormal cam wear. Cam wear as a result of improperly set Release Spring Figure 2 On Seam Eccentric Pin Figure 2 shows overtightening the release spring bolt will force the cam section away from the eccentric allowing the cam to float. Release Spring Figure 3 Figure 3 shows a correctly adjusted release spring bolt. In Normal operation there should be.030" minimum clearance between the head of the bolt and cam surface with bolt fully tightened or bottomed out. Off Seam e nc a r ea Cl Angelus Sanitary Can Machine Company Pacific Blvd. Los Angeles, CA /2

51 ALL20001A-7/11/07 SERVICE NOTICE Check Seaming Cam Wear Use a feeler gage at the transition area to check for clearance between seaming cam track and seaming cam roll. The minimum clearance is.002 and the maximum clearance is.020. Angelus suggests replacing the seaming cam when.020 clearance is obtained. 1st Operation Seam Cam Roll Check 2nd Operation Seam Cam Roll Check On Seam (pin is facing left) Off Seam (pin is facing right) View of clearance at off seam position. Minimum clearance between 1/2" x 4-1/4" socket head Nylok screw is.030 with bolt fully bottomed or tightened. Angelus Sanitary Can Machine Company Pacific Blvd. Los Angeles, CA /2

52 ALL24001B - 2/19/09 SERVICE NOTICE Can Feed Chain Assemblies Can Feed Chain Assembly stretch is rated at.050 of an inch for each section of the Assembly. This holds true with any can feed chain used on Angelus Seamers. As an Example; Model 180S Seamers using a 3.666" inch pitch chain measures evenly 33 inches over nine complete new sections. When this dimension reaches 33-7/16 inches it is recommended to consider a replacement Model 180S Seamer Can Feed Chain Model 121L Seamers with a 3-3/4 inch pitch measures evenly 37-1/2 inches over ten complete new sections. When this chain reaches 38" inches it is recommended that replacement be considered. All Can Feed Chains should be measured in 30 inch plus sections to determine actual accumulated stretch. NOTE: Can Feed Chain pitch will vary with all Seamers depending on the Seamer specifications and container diameter. A quick alternative method for measuring stretch is available as follows; 62H-82H616 Feed Can Gage (5.5 Can Feed Center) 121L-258L816 Feed Can Gage (3.75 Can Feed Center) 140S-38S416 Feed Can Gage (3.562 & Can Feed Centers) 180S-225S816 Feed Can Gage (3.562 & Can Feed Centers) Feed Chain Gage Aligned to Left Side/Pushing Edge of Chain Finger Align appropriate feed chain gage to the left side of chain finger or side that pushes can. All 3 chain fingers should line up to feed chain gage. If (1) chain finger or more have.050" stretch per section, it is recommended to replace feed chain immediately. Feed Chain Gage Feed Chain Finger Stretched Chain Note The Chain Finger is.050" Away From Gage PNEUMATIC SCALE ANGELUS

53 Service Notice ALL /27/00 Feed Chain Assemblies Whenever there is a replacement of the Feed Chain Assembly it is necessary to inspect the component parts, i.e. Wear Strips, Chain Take- Up and especially the Feed Chain Sprocket for wear and possible replacement. It is important you look for broken,bent,distorted or excessively worn Sprockets. The Sprockets normally wear on the side closest to the Gear Box. In addition inspect the Wear Strips for ripple conditions. If after inspection these components are in good condition, no further action is needed. If after inspection these components are worn or damaged, recommendation for replacement is advised. Angelus Sanitary Can Machine Company

54 Service Notice All /22/00 The Mounting Position of the Flange Bearings controls the height of the Sprocket being used. Lowers the Conveyor Sprocket Raises the Conveyor Sprocket L.Chong Example Angelus Sanitary Can Machine Company 1/1

55 Service Notice All26001A - 2/7/07 Subject: Proper Bonding Procedures for Stainless Steel (SS) Base Top Plates Seamer Models - 60L/61H/62H/80L/81L/100L/101L/120L/121L/12M/140S Purpose: To provide a appropriate method for secure bonding of (SS) base top plates. (SS) Base Top Plate Description: Loctite #573 is a flange sealant with medium strength for close fitting joints. Deviation on adhesives is not recommended due to adverse reactions possibly causing bearing corrosion or improper sealing allowing bacteria formation. Availability: Loctite #573 (Loctite Part# 26392) is available from distributors located on Loctite s website. Installation Procedure: Step 1) Clean base with oil free solvent such as acetone or isopropyl alcohol. All grease and oil must be removed. Step 2) Step 3) Step 4) Step 5) Step 6) Step 7) Step 8) Step 9) Step 10) Roughen the bond surface of the base with scotchbrite pad or emery cloth. Wipe again with solvent to remove loose particles. Repeat steps 1, 2, & 3 on the base top plate bottom surface. Plug any lube holes with pipe plugs. Apply Loctite #573 to the top surface of the base. Spread the Loctite #573 into a thin film using a putty knife or similar tool. Assemble the (SS) base top plate within 90 minutes. Adding Weight Fixture to Compress If possible add weights or additional fixturing as required to ensure base top plate remains as flat as possible. After 72 hours top plate and base will be fully cured and weights can be removed. Ref. Data Sheet #G10.60 Angelus 4900 Pacific Blvd. Los Angeles, CA Tel: (323) /1

56 Service Notice ALL /29/12 29L826 SEAMING ROLL RETAINING SCREWS Purpose To eliminate premature failure of acceptable Seamer Roll Retainer Screws. Description Because of stress failure in the field, 29L826 Seamer Roll Retainer Screw marked YFS are not longer used. 29L826 Seamer Roll Retainer Screw marked with FKE is the only acceptable fastener to be used in Seaming Roll application. As this screw is equipped with thread locking material, it is not intended to be reused once loosen. Use new screws only (DO NOT loosen then re-tighten or REUSE). When use to fasten Seaming Roll, it is recommended to torque screw to 14 ft-lbs. Refer to Figure -1. Figure-1: 29L826 Seamer Roll Retainer Screw Seamer Roll Thread Locking Material 29L826 Seamer Roll Retainer Screw Torque 14 ft-lbs NOTE: This is the property of Pneumatic Scale Angelus, do not duplicate or distribute without approval from Pneumatic Scale Angelus. Pneumatic Scale Angelus reserves the rights to modify, update, and obsolete this notice without further notification. PSAngelus Cuyahoga Falls, OH, Tel: (330) ;Los Angeles, CA, Tel: (323) ; Clearwater, FL, Tel: (727) ; Belgium, Tel: ; U.K. Tel: ; Dreieich, Germany, Tel: ; Hong Kong, Tel: /1

57 SEAMING CAM ECCENTRIC (Off Seam) PIN Installation Process SERVICE NOTICE Subject: Model 81L, 101L, 121L, 140S and 180S Seamer Seaming Eccentric Pin (Off Seam Pin) installation. Procedure: The Seaming Cam Eccentric Pin on all the above Seamers can only be installed with the 2nd Operation Cam section moved into the Off Seam position. The Eccentric Pin must be installed with dowel pin positioned to the right or Off Seam Position. Position of the Eccentric Pin when installing into the machine. 3/12/98-ALL28001 Eccentric Pin Dowel ANGELUS SANITARY CAN MACHINE COMPANY

58 Service Notice All 28002A - 11/10/11 MODELS 81L, 101L, 121L, 140S & 180S SEAMERS Seaming Cam Anchor & Eccentric Pins During 1st Operation Seam checks, the Anchor and Eccentric Pin Locknuts must be loosened slightly until the Eccentric Pin can be turned to the "Off Seam" position. When 1st Operation Seam checks are finalized, return the Eccentric Pin to the "On Seam" position and tighten Locknuts securely on the Anchor Pin and Eccentric Pin. Failure to tighten these locknuts for normal seamer operation may result in abnormal Seaming Cam wear. Seaming Cam Eccentric Pin Locknut Location Both Seaming Cam Pin Locknuts must be torqued to 20 ft/lbs before starting production. Tighten 1-3/8" socket Eccentric Pin Locknut until washer has slight movement. Torque to 20 ft/lbs. Caution: Overtightening Locknut will distort washer. PSAngelus Cuyahoga Falls, OH, Tel: (330) ;Los Angeles, CA, Tel: (323) ; Clearwater, FL, Tel: (727) ; Belgium, Tel: ; U.K. Tel: ; Dreieich, Germany, Tel: ; Hong Kong, Tel: /1

59 SERVICE NOTICE Main Drive Belt Tension Procedure* Machine equipped with Gates Tri-Power Molded Notch V-Belts. 3/2/98-ALL30001 Procedure; Step one Measure the Span length between the Drive and Driven Pulley Shaft centers and mulitiply by 1/64th inches. This will be the deflection measurement on each belt. A common fish scale or Gates Tension Tester No can be used to check deflection versus poundage. Step two Adjust belts using the handwheel and Motor Base adjustment Screw until Belt tension is measured at 13 to 18 lbs when deflected by the calculation from the first step. Belt Span inches x 1/64" = Deflection *This Belt Tension procedure has been taken from the Gates Rubber Company Belt Tensioning Section of their catalog and applies to the Tri-Power (CX) belts supplied with the Seamer. Under or over tensioning belts will reduce the life of belts. ANGELUS SANITARY CAN MACHINE COMPANY

60 Electric Tooth Clutches (Sepac) SERVICE NOTICE 3/29/93-ALL H, 121L, 140S & 180S Seamers Electric Tooth Clutch Applications are as follows; Filler Drive / Seamer Safety Clutch Assemblies Seamer Torque Description Part Number Model No. Rating 62H Seamers 300 ft. lb. Electric Tooth Clutch *F 244H633 AAA 6 121L Seamers 600 ft. lb. Electric Tooth Clutch **F 854L833 AAA 6 140S Seamers 600 ft. lb. Electric Tooth Clutch F 124S833 AAA 2 180S Seamers 600 ft. lb. Electric Tooth Clutch F 124S833 AAA 2 Inching Mechanism used on Model 180S Seamer Only. (optional) 180S Seamer 300 ft. lb. Electric Tooth Clutch F 123S833 AAA 3 Spare Parts for Electric Tooth Clutches 244H633, 854L833, & 123S833 (3) Spring F 123S833 AAB 1 (3) Spacer F 123S833 AAC 9 (3) Screw F 123S833 AAD 7 Spare Parts for Electric Tooth Clutch 124S833 (140S & 180S only) (3) Spring F 124S833 AAB 0 (3) Spacer F 124S833 AAC 8 (3) Screw F 124S833 AAD 6 * Same part as 652L833 (300 ft. lb. rating). Number changed to 244H633 now used only on Model 62H Seamers. ** 854L833 replaces 652L833 (300 ft. lb. rating) previously used on all Model 121L Seamers. Customers ordering 652L833 Clutches for their 121L Seamers will automatically be shipped the higher torque 854L833 Clutch. ANGELUS SANITARY CAN MACHINE COMPANY

61 SERVICE NOTICE OIL RECIRCULATION AND FILTRATION SYSTEM (29H614) Installing Heater Blanket 293H633 Scope: This Heater Blanket is supplied as an optional device in cases where the oil temperature seldom gets above 60 0 F. during normal production. Oil at this temperature creates a higher than normal vacuum reading due to the heavier consistency of the oil. Once the temperature has been brought to 80 0 or more, the oil flows much easier and the system works as designed using 40W oils. 10/7/96-ALL33002 Description: The Heater Blanket package consists of a Heat Blanket with built in thermostat regulating temperature at F. before it will shut off. The kit contains terminal strip components to connect the blanket to 110VAC power supply within the Filtration System sub panel. The correct Wire length and fittings are also supplied. Installation: Find the incoming oil line or tube leading into the Bag Element (water separator) canister. Wrap the blanket around the canister closer to the top with the thermostat on the outside. On each end of the blanket are two open lace ties. Use the two tension springs supplied to hold the blanket in place. Make wire connections using components supplied. This requires 110VAC which can be found inside the sub-panel next to the Filter canisters. WARNING: Disconnect the main power supply before making wire connections. Heater Blanket 293H633 Tension Springs used to hold the blanket in place.

62 Service Notice All /28/06 Subject: 62H/81L/101L/120L/121L/140S/180S Seamers Motor Driven Elevator System GEMINI 4100 with Dual Counter Programming Purpose: The motor driven elevator system is used to raise or lower the seamer upper turret housing for pin height adjustment. The elevator system control box (Fiqure A) which are installed to seamers are pre-programmed by Angelus SCMC before the seamer leaves the plant, and should not need any programming once the seamer is installed. In the event that the elevator settings are lost due to an unforeseen occurrence, the elevator setting will need to be reprogrammed as follows. The elevator system control boxes shipped separately are not pre-programmed and will need to be wired onto seamer and programmed also as follows. Fiqure A Elevator System Control Box Front Cover Clamp Screws Dual Counter Display Unit Key Selector Switch Height Adjust Selector Switch Height Adjust Speed Potentiometer CAUTION: Do not operate the elevator system manually with the seamer service cover removed, and the power turned off. Digital readings will no longer be correct. Manual adjustments of the elevator system should be made only with the power on. Angelus 4900 Pacific Blvd. Los Angeles, CA Tel: (323) /5

63 Service Notice All /28/06 Programming Dual Counter Display Unit 1) Loosen the two clamp screws on the elevator control box front cover to open cover (Fiqure A). 2) On the rear on the dual counter display unit (Fiqure B) set the DIP switches #1 and #8 downand #2 thru #7 up. Fiqure B Dual Counter Display Unit (Rear) Dip Switches Jumper Wire 3) Remove the jumper wire from terminal 7 & 8 (Fiqure B). 4) On the front of the motor driven elevator system control box, move the key selector to "Adjust" mode (Fiqure A). 5) On the front side of the unit at the dual counter display unit (Fiqure C), enter the key in sequence (from left to right) as listed in (Table 1) This program setting is done so that the dual counter display unit can interpret the upper turret housing encoder signal for correct positioning of the turret. Fiqure C Dual Counter Display Unit (Front) Program the Mode Menu settings using the key with the same value. Spacing will fill in automatically. Angelus 4900 Pacific Blvd. Los Angeles, CA Tel: (323) /5

64 Service Notice All /28/06 Table 1 Initial Program Setting Press E Press E Press E Press E Press E Press E Press E Press 5 2 +/- 4 E Press 5 6 +/- 2 E Press E 6) Determine if the display will read in inches or millimeters and program for one or the other as follows. If the counter is to be displayed in inches, enter (Table 2) key sequence from left to right. NOTE: The decimal point automatically installs. Scale factor numbers are keyed in using the keys directly above each digits place. If the counter is to be displayed in millimeters, enter (Table 3) key sequence from left to right. Table 2 Inch Key Sequence Press E Press E Press 3 Press See Table 4 Press E Table 3 Millimeter Key Sequence Press E Press E Press 3 Press See Table 4 Press E Angelus 4900 Pacific Blvd. Los Angeles, CA Tel: (323) /5

65 Service Notice All /28/06 62H 81L/101L/120L/121L 140S/180S Table 4 Seamer Elevation Index To display in inches, using keys 1 thru 5, Enter To display in inches, using keys 1 thru 5, Enter To display in inches, using keys 1 thru 5, Enter To display in millimeters, using keys 1 thru 5, Enter To display in millimeters, using keys 1 thru 5, Enter To display in millimeters, using keys 1 thru 5, Enter ) On the rear of the display unit, replace the jumper wire between terminal connection 7 & 8. (This jumper wire prevents changes to the unit) (Fiqure B). 8) Measure the seamer pin height using an inside micrometer. 9) Press the 1 button on the display unit (Fiqure C). 10) Using the key pad on the display unit and enter in the measured value. 11) Press E and then R buttons on the display unit. 12) Close front cover and tighten the two clamp screws (Fiqure A). To Adjust Upper Turret Housing Height CAUTION: Before raising or lowering the upper turret housing, ensure that the upper turret columns are checked and cleared for this process as damage to elevator system may occur. Ensure key selector switch is in the "Off" mode while working inside seamer to prevent unintentional movement. 1) On the seamer, loosen the upper turret hub clamp (Fiqure E). 2) Loosen the upper turret hub seal clamp. When moving to shorter can heights, always go lower than the calculated pin height and adjust moving upward. Always check the pin height using an inside micrometer. 3) On the elevator system control box, move the key selector switch to "Adjust" mode. The upper turret elevation changes can now be made while observing the display. If programmed for inches, the display will decrease or increase by.001 increments (metric = 0.01mm increments). Angelus 4900 Pacific Blvd. Los Angeles, CA Tel: (323) /5

66 Service Notice All /28/06 4) Use the height adjust selector switch to move the upper turret up or down. Use the height adjust speed potentiometer to control the elevation change speed (Fiqure D). Fiqure D Elevation Controls 5) Tighten the upper turret hub clamp screws and the upper turret hub seal clamp screws to 50 ft. lbs initially then 80 ft. lbs. Fiqure E Upper Turret Hub Clamp Screws 6) Once the upper turret housing is set to the desired height, move key selector switch to "Run" mode. Angelus 4900 Pacific Blvd. Los Angeles, CA Tel: (323) /5

67 Service Notice All39001A - 4/23/07 Subject: General Seamer Washdown Procedures Pre-Wash CAUTIONS: Be certain that all gear case, electrical box or drive case covers are secure (i.e.; all fasteners holding covers in place). Do not remove any guards that expose areas above the seaming roll level of the seamer. Washdown should be confined to areas below the bottom face of the upper turret. When performing wash down maintenance, make safety a habit. Do not remove guards, clean, lubricate, or repair machinery while in motion. Washdown Settings: Air supply to the seamer (2 P.S.I.G.) should be dry and filtered clean before entering the machine. Regulate and limit water pressure to 20 P.S.I. when flushing out the cap feed turret through the gas inlet lines. (regulators are supplied with free standing enclosure units, otherwise to be supplied by user.) The high pressure water hoses used to wash down equipment should be restricted. Setting water pressure above recommended P.S.I., can in some cases, turn lip seals and allow water to enter. Use care and caution when the wash takes place. Adjust all hosedown & rinsing settings to low pressure (60-80 P.S.I.) & hot water (120 to 160 ). Washdown Procedure: 1) Open seamer enclosure doors and remove all cans, lids, and scrap. 2) Hose out the line lube and grease residual, plus any remaining slime. 3) Using heavy duty industrial paper towels, wipe off any grease from the seaming heads before hosing them off. 4) Using low pressure hose only, rinse off the inside of seamer, including heads, rolls, etc. 5) Apply detergent of user's choice that is compatible with the attached list of material. 6) After cleaning, all detergent should be removed by rinsing. Note: No detergents or chemicals should be left on machine longer than suppliers recommendation. Particular care should be taken to wash out all foreign materials from the machine. This is especially true of the machine base where these materials gather. 7) Hand scrub the following; gassing turret, seaming heads, discharge star, all guides - inside & outside of cover feed track and knives. 8) Hose the entire seamer with hot water (no high pressure). 9) Verify all areas including rolls and chucks are free of grease, slime, and lube. 10) Wipe down all areas with heavy duty industrial paper towels. 11) Lubricate seamer manually. After washdown, all seaming rolls must be lubricated and rotated * per Angelus specs. * For Seamers equipped with tapered roller bearing seaming rolls grease until visible. For Seamers equipped with ceramic bearing seaming rolls apply one shot of grease from a standard grease gun. Angelus 4900 Pacific Blvd. Los Angeles, CA Tel: (323) /3

68 Service Notice All39001A - 4/23/07 Material Specs/Manufacturer s STD 1015/AISI 1018/AISI 1020/AISI 1045/AISI 1117/AISI 1144/AISI 1215/AISI 4130/AISI 4135/AISI 4140/AISI 4340/AISI 4620/AISI 8620/AISI 8630/AISI 15-5 PH SS 17-4 PH SS 17-7 PH SS 1900 UHMW 301 SS 302 SS 302/4 SS 303 SS 304 SS 316 SS 319 Aluminum/ASTM 356-T-6 Aluminum/ASTM 410 SS 4140/42/AISI 416 SS 420V SS Material Specs/Manufacturer s STD 431 SS 440A SS 440C SS 440F SS 6061 Aluminum/ASTM DCI/ASTM 836 Bearing Red Brass/ASTM 862 Manganese Bronze/ASTM 922 Leaded Tin Bronze/ASTM 932 Bearing Bronze/ASTM 954 Aluminum Bronze/ASTM A2 Tool Steel/AISI A-915 SC 4130 Modified/ASTM Alloy Cast Iron (40K Class 40)/ASTM Alloy Cast Iron (Class 40 high nickel)/astm Alnico/ASTM Alum Brz Ampco 18/Proprietary Alum Brz Ampco 8/Proprietary Ampco 22W Alum Brz/Proprietary Asarco Brz Bar K4028/ASTM Beryllium Copper/ASTM Cast Halalloy Bronze/ASTM Cast Iron CL 30/ASTM Cast Iron CL 40/ASTM Celcon Cobalt Magnet Steel/ASTM Cromovan/ASTM Cromovan Nitrated/ASTM Cromovan Sub-Zero Treatment/ASTM Cromovan Titanium Nitrated Angelus 4900 Pacific Blvd. Los Angeles, CA Tel: (323) /3

69 Service Notice All39001A - 4/23/07 Material Specs/Manufacturer s STD D2 Tool Steel/AISI Delrin Ductile CI /ASTM Ductile CI /ASTM Ductile CI /ASTM Elmax/Proprietary Ertalyte/Proprietary Material Specs/Manufacturer s STD Teflon/RMA Titanium/ASTM Torlon 301/Proprietary Urethane Foam Vellumoid Viton/RMA Zinc Felt Kynar Meehanite Micarta Music Wire NCI 40 Nickel Cast Iron/ASTM Neoprene/RMA Ni-Resist/ASTM Nitrile/RMA Nylatron GS Nylon Oilite/ABMA Oilon PV 80/Proprietary Phosphorus Bronze/ASTM Polycarbonate Rulon LR/Proprietary SAE 660 Bronze Bar/ASTM Silicone Rubber/RMA Stellite 1 Alloy was Stoody or Weartech 1/Proprietary Stellite 1 Alloy Titanium Nitrated/Proprietary Stellite 1 Low Carbon (1.6% C)/Proprietary Stellite 2 Alloy/Proprietary Stellite 3 Alloy/Proprietary Angelus 4900 Pacific Blvd. Los Angeles, CA Tel: (323) /3

70 Service Notice All39002A-9/8/03 Subject: Upgrade and standardize air pressure control instruments for internal pressurization of Seamers with enclosed oil system. Purpose: Facilitate more accurate control of the recommended seamer internal pressure range of 2 to 3 psig and improve the ability to read the pressure gauge. Benefits: New regulator eliminates setting internal pressure in excess of the maximum recommended psig. New gauge (0-5 psig) improves accuracy setting of internal pressure and is easier to read. New water separator removes most moisture entering system through the incoming air. Improved durability and appearance. Gained benefits incur only a minor cost increase. Description: The new Air Precision Regulator (Part Number 13M239 Rev. A) is adjustable from 0.7 psig to a maximum pressure of 3.0 psig. Requires stainless steel bracket (Part Number 74M254). The new Pressure Gauge 0 to 5 psig (Part Number 27H639) has a 2.5-inch dial stainless steel case. Its diaphragm mechanism is the ideal analog choice for accurate measurements in this small pressure range. The Water Separator-Auto Drain (Part Number 10M239) is internally coated with epoxy paint. Requires stainless steel bracket (Part Number 7M254). Availability: All parts and components are currently available from stock. Additional information on required fittings, tubing and hardware is available on Engineering Data Sheets for specific machine models. Summary: We have discontinued the purchase of the old pressure regulator part number 18S839 (0 to 30 psig) and pressure gauge part number 56S839 (0 to 15 psig). These parts are Obsolete For Replacement Only until current stock is exhausted. Ref. Engr. Bul. #81 (Revised 8/29/03) Angelus 4900 Pacific Blvd. Los Angeles, CA Tel: (323) /1

71 Service Notice All39003A - 8/18/06 Subject: Replacement parts for 180L639 & 31L839 Pressure Regulators Purpose: Pressure regulators 180L639 & 31L839 are now obsolete. The 180L639 regulator has been replaced by 378L639 regulator. The 31L839 regulator has been replaced by 199L839 regulator. Both replacement regulators are the same size and capacity of the obsoleted regulators, however the inlet & outlet pipe sizes are different as shown. Description: 378L639 Regulator Seamer Models Replaced Parts Replacement Parts (1) 180L639 Regulator (1) 378L639 Regulator 40P, 50P, 60L, 61H, 62H, 81/101/121L, 140S (1) Close Nipple (1) 133L814 Close Nipple (1) to 3/4 Reducer (hex bushing) (1) 1.00 to 3/4 Reducer (hex bushing) Angelus 4900 Pacific Blvd. Los Angeles, CA Tel: (323) /5

72 Service Notice All39003A - 8/18/06 Description: 378L639 Regulator Seamer Models Replaced Parts Replacement Parts 180S Turret Gassing w/triple Bubble Breaker (1) 180L639 Regulator (1) 378L639 Regulator (2) Close Nipple (2) 133L814 Close Nipple Ref. Engr. Bulletin #64 Angelus 4900 Pacific Blvd. Los Angeles, CA Tel: (323) /5

73 Service Notice All39003A - 8/18/06 Description: 199L839 Regulator Seamer Models Replaced Parts Replacement Parts 80/120L, 81/101/121L, 140S (Single Speed Gas Control System) (1) 31L839 Regulator (1) 199L839 Regulator (1) Close Nipple (1) 133L814 Close Nipple (1) to 3/4 Reducer (hex bushing) (1) 1.00 to 3/4 Reducer (hex bushing) Angelus 4900 Pacific Blvd. Los Angeles, CA Tel: (323) /5

74 Service Notice All39003A - 8/18/06 Description: 199L839 Regulator Seamer Models Replaced Parts Replacement Parts (1) 31L839 Regulator (1) 199L839 Regulator 81/101/121L (Dual Speed Gas Control System) (1) to 3/4 Bushing (1) 1.00 to 3/4 Bushing (1) Street Elbow (1) Street Elbow (1) 1-1/4 Close Nipple (1) 133L814 Close Nipple Angelus 4900 Pacific Blvd. Los Angeles, CA Tel: (323) /5

75 Service Notice All39003A - 8/18/06 Description: 199L839 Regulator Seamer Models Replaced Parts Replacement Parts 180S (Turret Gassing w/triple Bubble Breakers) (1) 31L839 Regulator (1) 199L839 Regulator (2) Close Nipple (2) 133L814 Close Nipple Ref. Engr. Bulletin #63 Angelus 4900 Pacific Blvd. Los Angeles, CA Tel: (323) /5

76 Service Notice All /7/06 Subject: Steam Vacuum Control Systems - Free Standing, PLC, or PC Controlled Seamer Models - 60L, 61/62H, 80/100/120L, 81/101/121L,12M Purpose (Low Flow Vari Speed System): The low flow vari speed steam vacuum system allows the user to start, increase, decrease, and stop the steam flow from the remote control or from a preprogrammed menu that has been established to produce consistent quality of a product at the chosen cans per minute production rate. Benefit (Low Flow Vari Speed System): Saves production time and energy. When a seamer is readied for production and the system is cold, the flow can be set to a temporary high value that will expedite warm up then reduce flow to what is required as cans start entering the can feed extension. A temporary interruption of filled cans will put the seamer on standby. The steam can then be adjusted to deliver sufficient flow to maintain the system hot enough and ready for a quick change to production flow. When seamer service requires prompt interruption of steam flow, a stop steam flow command will make it happen immediately. It is recommended to also shut off the main steam service valve also as a safety precaution. Description (Low Flow Vari Speed System): The system has been designed and configured to deliver and control saturated steam in a flow range from 5 to 30 lbs/hr. The PLC controller and operator station are supplied and programmed by user. The system must be located as close as possible to the right corner of free standing enclosure to minimize the production of condensate. The system requires a dry air source psi. Availability (Low Flow Vari Speed System): Per Parts List 121LD269 for 5-30lbs/hr System Operation Procedure (Low Flow Vari Speed System): Ref. Data Sheet #G10.58 for Electrical Schematic - Transmitter Configuration Ref. Data Sheet #G10.59 for Mechanical Specifications and Operation Guide Dimensions (Low Flow Vari Speed System): Height 51.8, Width 26.9, Depth 14.2 Low Flow Vari Speed Steam Vacuum Control System 5-30lbs/hr (Parts List 121LD269) Angelus 4900 Pacific Blvd. Los Angeles, CA Tel: (323) /2

77 Service Notice All /7/06 Purpose (Vari-speed System): Introduction of a new vari-speed steam vacuum flow control system designed as a retrofit for any Angelus steam vacuum seamer model supplied without a freestanding machine enclosure. Benefit (Vari-speed System): Increases production efficiency and provides a consistent steam flow delivery. The vari-speed steam vacuum flow control system uses a PLC program for a specific can size, product and speed. Adjustments using a PLC is quick and easy to make, thus eliminating any approximating of steam settings by use of a screwdriver. The vari-speed steam vacuum flow control system reduces the time required to begin steam flow operation and conserves the output of unneeded steam. Description (Vari-speed System): The compact stand-alone vari-speed steam vacuum flow control system can be preprogrammed and required steam flow settings may be selected from a menu for a specific product, can size or cans per minute. The piping and most hardware are constructed from stainless steel. This system has been designed and the vortex flow meter is pre-configured for a typical steam flow of 15 to 80 lbs/hr. The remote transmitter produces a signal to display actual flow next to the set point in HMI. The PLC and HMI which are supplied by user, send a signal to the control valve. The system is supplied standard with 50 foot of cable, and additional lengths are available upon request. Safety guarding (not shown) is provided to ensure the safety of operating personnel. Availability (Vari-speed System): Per Parts List 120LD162 for 15-80lbs/hr System Operation Procedure (Vari-speed System): Ref. Data Sheet #G10.54 for Electrical Schematic - Transmitter Configuration Ref. Data Sheet #G10.55 for Mechanical Specifications and Operation Guide Vari-speed Steam Vacuum Control System 15-80lbs/hr (Parts List 121LD162) Dimensions (Vari-speed System): Height 55.19, Width 33.58, Depth Angelus 4900 Pacific Blvd. Los Angeles, CA Tel: (323) /2

78 Service Notice Lower Lifter (Chuck) Springs All40001C-2/28/07 Model Part # Drwg. # Max/lbs. Range lbs./in. Deflect Size Color 10P 1P140 A # n/a 1/32 1-5/16 x 2-1/4 n/a 29P/29P42 40P 75P/85P 29V/59V * Special for Fibre Cans 50P-59P 93P/94P 60L *Spacer req d under spring 2P240 A # /16 1-1/16 x 1-1/2 n/a 4P240 A # /8 1-1/16 x 1-1/2 n/a *7P240 A # /8 1-1/8 x 1-5/8 n/a 9P240 A # n/a 1-1/8 x 1-5/8 n/a 15P240 A # /8 1-1/8 x 1-1/2 Black 1P540 A # /8 1-3/16 x 2 Black *3P540 A # n/a 1-1/8 x 1-7/32 n/a 8P240 A # n/a 1/8 1-7/32 x 1-1/2 Blue/Green 40L 1L440 A % Deflection /8 x 3/4 x 2 Gold 5L440 A % Deflection n/a 3/8 x 3/4 x 2 Bronze 60L Non driven lower lifters 41L 60L (driven lower lifters) 61H/62H/63H 80L/100L/120L 81L/101L/121L 24L640 A # /8 1-1/4 x 2 Gold 28L640 A # /8 1-7/32 x 2 Black 31L640 A # /8 1-7/32 x 2 Blue 32L640 A # /8 1-7/32 x 2 Rust 44L640 A # n/a 1/8 1-1/4 x 2-1/2 n/a 7L840 A # /8 1/2 x 1 x 1-1/2 Blue 8L840 A # /8 1/2 x 1 x 1-1/2 Red 9L840 A # /8 1/2 x 1 x 1-1/2 Copper 10L840 A # /8 1/2 x 1 x 1-1/2 Green Angelus 4900 Pacific Blvd. Los Angeles, CA Tel: (323) /2

79 Service Notice Lower Lifter (Chuck) Springs All40001C-2/28/07 Model Part # Drwg. # Max/lbs. Range lbs./in. Deflect Size Color 41L 60L (driven lower lifters) 61H/62H/63H 80L/100L/120L 81L/101L/121L 31L840 A # /8 1/2 x.95 x 1-3/4 Gray 140S/180S 2S840 A % Deflection /8 x 3/4 x 1-3/4 Yellow 3S840 A % Deflection /8 x 3/4 x 2 Green 5S840 A % Deflection /8 x 3/4 x 1-1/2 Yellow 7S840 A % Deflection /8 x 3/4 x 1-1/2 Blue 8S840 A % Deflection /8 x 3/4 x 1-1/2 Red 4M/5M/12M 2M240 A # /8 x 3/4 x 3 Purple 5M240 A # /8 x 3/4 x 3 Black Angelus 4900 Pacific Blvd. Los Angeles, CA Tel: (323) /2

80 Service Notice All41002A-1/18/02 New Double Profile 9P441 or 10P441 Seaming Roll Ball Bearing Upgrade Angelus has a new bearing available for double profile seaming rolls to further increase the seaming roll bearing life. The (2) 99P416 Ball Bearings are replaced with (2) 98P416 Ball Bearings. Action: If you have any un-used double profile 9P441 or 10P441 seaming rolls, please contact Angelus Parts Department Los Angeles, CA. by phone or for a return authorization number to send back the seaming rolls. Phone (323) or parts@angelusmachine.com Angelus will exchange the bearings and return parts without charge. Parts can not be accepted without a return authorization number. 13P441 (1st. Operation) 14P441 (2nd Operation) 96P416 98P416 * 9/10P441 *Indicates Parts to be Updated 100P416 34P417 98P416 * 29L826 97P P416 Optional Wrench 35P417 Angelus Sanitary Can Machine Company

81 Service Notice ALL /29/12 26L816 BALL BEARING REPLACEMENT Purpose To replace defective bearings in the field. Description MODELS 60L AND 80L-121L, SEAMERS New issued 26L816 Ball Bearings will have 32-balls/16 per row with a protective cage. Check 17L844 and 496L644-Shaft's Outside Diameters/bearing shoulder before installing bearing. The Shaft's Outside Diameter (OD)/bearing shoulder should be greater than ø1.980 for better bearing surface contact against 26L816-Ball Bearing. If Shaft's Outside Diameter (OD)/bearing shoulder is less than ø1.980, replace existing shaft with new shaft of ø2.000 ±.020 Outside Diameter (OD). Refer to Figure-1. NOTE: Due to variances in bearing standards, Pneumatic Scale Angelus recommends a shaft shoulder diameter of ø2.000 ±.020. All new 17L844 and 496L644 Drive Shafts will have this new diameter incorporated. Figure -1: 26L816 Ball Bearing 80L-121L Main Pinion Drive Shaft 17L844 Drive Shaft 26L816 Ball Bearing Cage 26L816 Ball Bearing 32-Balls/16-Balls Per Row with Cage 60L Main Pinion Drive Shaft 26L816 Ball Bearing 496L644 Drive Shaft OD Bearing Shoulder ø2.000 ± L 496L644 Drive Shaft NOTE: This is the property of Pneumatic Scale Angelus, do not duplicate or distribute without approval from Pneumatic Scale Angelus. Pneumatic Scale Angelus reserves the rights to modify, update, and obsolete this notice without further notification. PSAngelus Cuyahoga Falls, OH, Tel: (330) ;Los Angeles, CA, Tel: (323) ; Clearwater, FL, Tel: (727) ; Belgium, Tel: ; U.K. Tel: ; Dreieich, Germany, Tel: ; Hong Kong, Tel: /1

82 Service Notice ALL /18/06 Subject: Stainless Steel Replacement Handles for Part Numbers 234H654 (Latch RH) and 235H654 (Latch LH) Purpose: To provide stainless steel material on both the latch and latch components for improved corrosion resistance. Benefit: The corrosion resistance of the latch and latch components now matches the corrosion resistance of the stainless steel enclosure. The improved latch & components can withstand harsher environments with less replacements. Description: The revised (Rev. C) latch and components are manufactured from 300 series stainless steel material. Availability: Revision C latches are a direct replacement to existing handles. The back latch is not included. Back Latch is not Included Use with the original back latch if it is stainless steel. If needed the stainless steel back latches can also be purchased as follows; S0131L254AAAA0-----Door Latch S0142L254AAAA7-----A Door Latch S0142L254AAAB0-----B Door Latch Ref. Engr. Bulletin #103 Angelus 4900 Pacific Blvd. Los Angeles, CA Tel: (323) /1