Description. ST-164 Dual injector. User Manual ST-164. Artikel-Nr.: XXX
|
|
|
- Derek Warren Barber
- 5 years ago
- Views:
Transcription
1 ST-164 Dual injector Description The ST-164 is an injector unit for admixing liquid detergent concentrates with water using the venturi principle. Via a selector lever (see photos below) two alternative detergents can be selected for admixing. A third selector lever position makes it possible to flush the unit clear without any detergent intake. Via an optional compressed air connection compressed air can be added to the detergent/water mixture. Any accessory components needed for this can be found in the spare parts drawing at the end of these Operating Instructions. Selector lever switching positions Rinsing Detergent 1 Detergentl 2 1
2 Safety Hazard If these instructions are not followed there is a danger of physical injury, danger to life and material damage! Please comply with the Operating Instructions! Incorrect operation can lead to serious injury. Read the Operating Instructions before you use the appliance. Danger of injury due to high pressure! Do not spray objects containing substances injurious to health, which conduct electricity or which are fragile! General safety notes To guarantee safe operation the injector unit may only be used in accordance with these Operating Instructions. Keep these Operating Instructions in a safe place for later reference. Please also observe the safety instructions for the detergent and if applicable of the high pressure cleaner manufacturer. Do not mix detergents one with the other. Wear suitable protective clothing and gloves when working. Never direct the high-pressure jet at persons or other living creatures. Read the safety data sheets and observe the corresponding safety and handling regulations. In addition the required safety and legal regulations for the respective type of use must be observed. This also applies to all accessories used. 2
3 Intended Use The ST-164 injector unit is designed for admixture of detergents with water and for straightforward rinsing with water. Only Pressure Equipment Directive (PED) Group 2 liquids may be used as media. In case of doubt contact the equipment manufacturer. The unit may only be used with a suitable pressure generator. The unit is not designed for use with persons (children included) with restricted sensory and mental capabilities due to lack of experience and/or lack of knowledge unless they are supervised by a person responsible for their safety or if they have received instruction from that person in use of the equipment. In general children are forbidden to use this equipment. Connection lines used and the ST-164 injector unit itself must be flushd clear for 20 seconds prior to any change of detergent. In the case of very powerful detergents please contact the manufacturer who can then assess whether operation with this unit is possible. Any form of operation of the ST-164 injector unit over and above is deemed impermissible. Qualified personnel The bypass injector may only be installed by qualified personnel able to operate the bypass injector properly. Qualified personnel are persons familiar with installation, commissioning and decommissioning, operation, maintenance and repair and who hold a qualification appropriate to their work. Commissioning The ST-164 Dual Injector Unit may be secured either with the optionally available wall bracket or with a panel design fitment. Position detergent canisters in the vicinity of the injector unit. They should be no more than 3m distant from the injector unit. Select the appropriate dosage nozzles. Connect the intake suction hoses for the detergent to the ST-164 detergent connectors. 3
4 Do not confuse hoses and canisters! Connect a suitable hose to the injector unit outlet. Connect a suitable spray attachment. Connect the injector unit to the pressure generator. Set the injector unit to clear flush (selector lever in the intermediate position). Check all connections. Securing with wall bracket Assembly set for wall mounting (Product code ) Panel mounting Place the ST-164 as shown in the panel mounting bracket plate. 4
5 Template with panel mounting hole pattern You can overlay this matching template on the bracket plate provided and then drill the holes as illustrated. Please note that the maximum mounting plate thickness of 3mm must not be exceeded. 5
6 Adjusting the dosage rate Table reading example for dosage nozzle Flow volume: 15 l/min Detergent or disinfectant concentration: 5 % Calculated in accordance with the following data: (5 % * 15 l/min) / 100 % = 0,75 l/min (dosage rate) => nozzle selection 1,2 (read from diagram) Sample reading from graph (for this the optional ST-161 dosage valve is needed) Flow volume: 15 l/min Detergent or disinfectant concentration: 3 % Calculated in accordance with the following formula:: (3 % * 15 l/min) / 100 % = 0,45 l/min (dosage rate) => graph setting 2 (read from diagram) 6
7 ST-164 dual injector nozzles are interchangeable. By suitable nozzle selection it is possible to adjust the injectors to match virtually all feasible applications. The choice of injector nozzle combination influences definitively the quantity of maximum detergent induces under suction (concentration) and resistance of the injector to pressure losses caused by the accessories (hoses, spray attachment etc.) Each injector consists of two nozzles - the injector nozzle itself and the counter nozzle. Counter nozzle Injector nozzle 7
8 Changing injector nozzle and diffusor nozzle To change the injector and diffusornozzles first release the four bottom fixing screws (1). You can then remove the lower injector unit (2) together with the PEEK disc (6) from the upper injector unit (7). Remove the PEEK disc (6). Please note that the two O-rings can drop off! By screwing in an M4 screw remove the injector nozzle (4) from the lower injector unit (2). The diffusornozzle can now be removed from the lower injector unit (2) with a screwdriver. Carry out work on the injector unit clean surroundings. Use suitable tools. Please be careful not to lose small parts. 8
9 Overview injector nozzles - counter nozzles ST-164 Counter-pressure diagram ST-164 Most applications can be covered by standard combinations pre-tailored in consultation with us: For high-pressure applications of 80 bar and above we recommend: 9
10 Combination Unit 1,3-1, Litres 1,6 2, Litres 1,8 2, Litres 2,4 2,8 > 25 Litres For low-pressure applications we recommend: Combination Unit 2,1-2,8 25 bar + compressed air 2,4 - -2,8 < 25 bar 10
11 Changing dosage nozzles Dosage nozzles make it possible to restrict the intake suction flow volume or detergent concentrate from both detergent connectors (Chem 1 and Chem2) so as to adjust the concentration of detergent in the water. You can obtain a basic dosage nozzle set (restrictors) under the following product code: Restriction Bag ST-163 Remove the intake hose. Withdraw the old dosage nozzle from the induction socket. Insert the new dosage nozzle into the induction socket. There is an O-ring for each dosage nozzle. During assembly please ensure that the O-rings are not damaged. For choice of dosage nozzles see "Dosage Adjustment" Chapter Injector nozzle to large counter nozzle => high intake level and low counter-pressure tolerance Example: Input pressure 100 bar, injector nozzle 1.3 and counternozzle 2.8 => 2 litres induction level and diffusor-pressure tolerance 27 bar Injector nozzle to small counter nozzle => low induction level and higher counter-pressure tolerance Example: Input pressure 100 bar, injector nozzle 1.3 and counter nozzle 1.7 => 0.5 litre induction level and diffusor-pressure tolerance 52 bars All details are approximate values only. 11
12 Higher diffusor-pressure tolerance means that pressure losses caused by fittings, hoses, sprayguns etc. may also be higher. Diffusor-pressure tolerance reflects the maximum diffusor-pressure level at which injector induction suction continues. ST-164 Operating Modes Operating Mode 1: Operation without compressed air The ST-164 injector unit can be used simply as a cleaning medium injector (preferably at high pressure). Here the injector unit is incorporated in the water supply downstream of the pressure generator. Figure 1a: Selection between two alternative detergents and a clear flush position can be made via the selector lever. Figure 1b: At pressures > 70 bar foaming detergents can be foamed effectively with an air injector using a separate foam lance with an air injector. Available foam lances are for example the ST-72, ST-74 and ST-75. Assembly layout: Use withdetergent (Figure 1a) 12
13 Assembly layout: Use with foaming agent t (Figure 1b) Operating Mode 2: Operation with compressed air For this operating mode you need the ST-164 check valve. ST-164 check valve (Product Code ) 13
14 To install the ST-164 check valve you must first unscrew the blanking plug with O-ring from the ST-164 injector unit (Diagram 1). The ST-164 check valve is then screwed in (Diagram 2). Compressed air can then be connected to the ST- 164 non-return valve. Bild 1 Bild 2 Foaming with compressed air is particularly suited to generating foam at low water pressures: 3-70 bar Assembly layout with detergent 14
15 Spares Below is a list of individual ST-164 parts: Disposal 15
16 Please dispose of old unit in an environmentally-friendly manner Old units contain valuable recycling materials which should be forwarded to a recycling facility. Please dispose of old units therefore via appropriate collection points. Troubleshooting ST-164 without compressed air Injector does not suck in foaming agent or detergent from the container or no foam is generated: Dosage nozzle blocked - clear nozzle with thin wire as necessary. If strongly scaled select new dosage nozzle. Selector lever in wrong position Intake suction hose damaged Intake suction hose not immersed in foaming agent High-pressure hose too long /nominal bore to small (minimum bore 8) Foam lance used without injector => select foam lance with injector Check non-return valve whether piston operates smoothly or shows signs of damage, replace as necessary. Foam lance nozzle too small => select lance with larger air injector nozzle ST-164 with compressed air Injector does not suck in foaming agent or detergent from the container or no foam is generated: Dosage nozzle blocked - clear nozzle with thin wire as necessary. If strongly scaled select new dosage nozzle. Selector lever in wrong position Intake suction hose damaged Intake suction hose not immersed in foaming agent Air connection not correct or not connected in the first place Compressed air line shut-off valve closed Connection of a pressure reducer in the compressed air line (2 6 bar) High-pressure hose too long /nominal bore to small (minimum bore 12) Foam lance used with air injector Check non-return valve whether piston operates smoothly or shows signs of damage, replace as necessary.. Equipment with too small cross-sections used. 16
General safety notes
Description The ST-164 is an injector unit for admixing liquid detergent concentrates with water using the venturi principle. Via a selector lever (see photos below) two alternative detergents can be selected
HOT WASHER MODEL NO: KING 125 OPERATION & MAINTENANCE INSTRUCTIONS PART NO: LS1009
HOT WASHER MODEL NO: KING 125 PART NO: 7320170 OPERATION & MAINTENANCE INSTRUCTIONS LS1009 INTRODUCTION Thank you for purchasing this Hot Washer. This machine is a portable, high pressure power washer,
Sectional and Tilting Door Opener
Sectional and Tilting Door Opener Installation Instructions and User Guide 600 800 1000 S/N WARNING Please read the manual carefully before installation and use. The installation of your new door opener
Sectional and Tilting Door Opener Installation Instructions and User Guide
Sectional and Tilting Door Opener Installation Instructions and User Guide ET-600E ET-800E ET-1000E S/N WARNING Please read the manual carefully before installation and use. The installation of your new
SECTIONAL AND TILTING DOOR OPENER INSTALLATION INSTRUCTIONS AND USER GUIDE. Comfort 800E/1000E
SECTIONAL AND TILTING DOOR OPENER INSTALLATION INSTRUCTIONS AND USER GUIDE Comfort 800E/1000E WARNING Please read the manual carefully before installation and use. The installation of your new door opener
Electric Pressure Washer
FEATURES This lightweight, portable high-pressure washer makes the toughest clean-up tasks faster and easier. Weighing only 43 pounds, you can take it virtually anywhere. Ideal for light industrial applications
Foam Equipment & Accessories
Suttner Foam Guns & Accessories 40 Foam Lances 4 Foam / Chemical Injectors 4 Foam Injector Lances 42 Foodjet - Food Hose 42 blufood - Food Hose 42 Suttner Foam Units 43 Airless Foamer 44 Foam Equipment
Operating and Installation Instructions Diaphragm Vacuum Pumps and Compressors
Operating and Installation Instructions Diaphragm Vacuum Pumps and Compressors Type range: UN813.3ANI UN813.4ANI UN813.3ANDCB UN813.4ANDCB UN813.5ANI Fig. 1: UN813.3ANI Fig. 2: UN813.4ANI You have selected
Porte 150 Users Manual Swing Gate Opener 24V DC
Porte 150 Users Manual Swing Gate Opener 24V DC for residential use only Signal Light Push-button Control Box 14 Contents 1. Important Safety Information 2. Product Description and Application 2.1 Application
Installation and Operating Manual for Tank and Equipment Cleaning Nozzles Series 5TM
Installation and Operating Manual for Tank and Equipment Cleaning Nozzles Series 5TM 150 150 150 This instruction manual contains proprietary information which is protected by copyright laws. No part of
Operating instructions Accu Jet
Operating instructions Accu Jet Keep for future use! Ident number: 04.8800.000 Air Line Table of contents 1 Scope of delivery... 4 2 Operator instructions... 5 3 Safety... 6 3.1 Intended use...8 4 Description
Angle seat valve with piston actuator VZXA-...-K
Angle seat valve with piston actuator VZXA-...-K Festo AG & Co. KG Postfach 73726 Esslingen Germany +49 711 347-0 www.festo.com 3 Further information Accessories www.festo.com/catalogue Spare parts www.festo.com/spareparts
F 167/94 07/ GM-
5.956 172 F 167/94 07/95 1750 GM- 1750 GM 3 4 2 5 1 16 7 6 8 9 10 15 11 14 12 13 9 1. Unit Start-Up 1750 GM 1 Spray lance with pressure control 2 Spray lance extension 3 Hand gun 4 Safety catch 5 Handle
Instructions for use and installation Cooker Hood
Instructions for use and installation Cooker Hood FTU 3807 WXS 70H FTU 3807-P WXS 70H Instructions Manual INDEX RECOMMENDATIONS AND SUGGESTIONS...18 CHARACTERISTICS...19 INSTALLATION...20 USE...24 MAINTENANCE...25
STIHL AP 100, 200, 300. Safety Precautions
{ STIHL AP 100, 200, 300 Safety Precautions English Contents Translation of Original Instruction Manual Printed on chlorine-free paper Printing inks contain vegetable oils, paper can be recycled. 1 Safety
#9040 FUEL TANK SWEEPER
#9040 FUEL TANK SWEEPER INSTRUCTION MANUAL FILTERS AND REMOVES FINE BIO-CONTAMINANTS, ALGAE, ETC. SWEEPING PROCESS REMOVES LARGE CONTAMINANTS FROM OIL TANKS SUCH AS RUST, WATER, CRUDE AND DIRT CIRCULATES
GF Spin Finish Pump. Translation of the Original Operating Instruction. Edition:
Translation of the Original Operating Instruction Edition: released: Status: Document no.: Contract no.: V11 01/2018 1-007-3296 Oerlikon Barmag Zweigniederlassung der Oerlikon Textile GmbH & Co. KG Leverkuser
Installation, Operation, and Maintenance Manual
Industrial Process Installation, Operation, and Maintenance Manual Series PBV Plastic Lined Ball Valve Table of Contents Table of Contents Introduction and Safety...2 Safety message levels...2 User health
Angle seat valve with diaphragm actuator VZXA-...-M
Angle seat valve with diaphragm actuator VZXA-...-M Instructions Operating (Translation of the original instructions) Festo AG & Co. KG Ruiter Straße 82 73734 Esslingen Germany +49 711 347-0 www.festo.com
Angle seat valve with piston actuator VZXA-...-K
Angle seat valve with piston actuator VZXA-...-K Instructions Operating (Translation of the original instructions) Festo AG & Co. KG Ruiter Straße 82 73734 Esslingen Germany +49 711 347-0 www.festo.com
Porte 300 Users Manual Swing Gate Opener 24V DC for residential use only
Porte 300 Users Manual Swing Gate Opener 24V DC for residential use only Signal Light Push-button Control Box Gate 2 Gate 1 Contents 1. Important Safety Information 2. Product Description and Application
Service Handbook HD /97
Service Handbook HD 1050 5.905-032 07/97 Foreword HD 1050 Foreword Indispensable prerequisites for the competent execution of service procedures are comprehensive, real-life training workshops for technical
User Manual TABLE MAGNIFIER TL-70. User-friendly Manual ID: #05007
User Manual TABLE MAGNIFIER TL-70 MANUAL DEVELOPED IN GERMANY myhansecontrol.com User-friendly Manual ID: #05007 Contents Overview... 4 Device parts... 5 Scope of delivery/device parts...6 Preface... 7
Oil-free piston compressors KK and piston vacuum pumps KV
Oil-free piston compressors KK and piston vacuum pumps KV Installation and Operating Instructions 0678106030L02 1707V003 Contents Important information 1 About this document 2 1.1 Warnings and symbols
RO Automatic trailer coupling. Repair instructions. 5KPVM02000 Towing Hitch Automatic Rockinger RO244A
utomatic trailer coupling Repair instructions 5KPVM02000 Towing Hitch utomatic Rockinger RO244 5KPVM02010 Towing Hitch utomatic Rockinger foot operated RO244L Contents 1 General Validity and application
Operator s and Maintenance Manual
Industrial Cleaning Machines Floor Scrubbers - Battery Version Operator s and Maintenance Manual HAZAN ISI VE MAKİNA SANAYİ LTD. ŞTİ. KISIKLI CAD.NO.79 ALTUNIZADE 34662 İSTANBUL-TÜRKİYE TEL : +90 216 321
100 Gallon Skid Sprayer
100 Gallon Skid Sprayer Model #: KS100P17 User Manual Read this manual for complete instructions Model #: KS100P17 Table of Contents Warranty... 3 General Safety Information... 3 Hazardous Substance Alert...
NEOTECHA NTB-NTC BALL VALVES INSTALLATION AND MAINTENANCE INSTRUCTIONS
Before installation these instructions must be fully read and understood 2 SAFETY Please also read through these notes carefully. 2.1 General potential danger due to: a. Failure to observe the instructions
Instruction Manual. Automatic Fuel Oil De-aerator Flow-Control. Flow-Control 3/K-1 # Flow-Control 3/K-2 # 70019
Mess-, Regel- und Überwachungsgeräte für Haustechnik, Industrie und Umweltschutz Lindenstraße 20 DE-74363 Güglingen Telefon: +49(0)7135-102-0 Service: +49(0)7135-102-211 Telefax: +49(0)7135-102-147 E-Mail:
Installation manual wall-mounted distributor
EN Installation manual wall-mounted distributor EN 60003233 Issue 11.2016 2016-14-11 Table of contents 1 About this manual 3 1.1 Structure of the warnings 3 1.2 Symbols used 4 1.3 Signal words used 4 2
OPERATION & MAINTENANCE INSTRUCTIONS
WARNING Read the instructions before using the machine PETROL DRIVEN POWER WASHER MODEL NO: TIGER1700 PART NO: 7320054 OPERATION & MAINTENANCE INSTRUCTIONS LS0511 2 INTRODUCTION Thank you for purchasing
C3 Operating Instructions
Version 3.1 Stand 09.2014 Robert Bosch (Australia) Pty. Ltd. 1555 Centre Road Clayton, Victoria 3168 C3 Operating Instructions For further information please contact Bosch at: Australia 1300 30 70 40 www.boschautoparts.com.au
AIRCLEAN 32 USER MANUAL. High-pressure cleaner. Wilhelmsen Ships Service. Produced in Norway for:
AIRCLEAN 32 High-pressure cleaner USER MANUAL Produced in Norway for: Wilhelmsen Ships Service Contents E.1 IMPORTANT INFORMATION 3 E.1.1 Safety 3 E.1.2 Lubrication 3 E.1.3 Air operating pressure 3 E.1.4
INDECO LUBEMAXX. Operating and Assembly Manual INDECO LUBEMAXX
INDECO INDECO TM Operating and Assembly Manual AUGUST 5, 206 35 Research Drive, Milford, CT 06460 USA Office: (203)73-030 Fax: (203)73-040 www.indeco-breakers.com INDECO INDEX Section A General Safety
PETROL DRIVEN POWER WASHER
WARNING: Read these instructions before using the machine PETROL DRIVEN POWER WASHER MODEL NO: TIGER 2500/2900 PART NO: 7320055/7320056 OPERATION & MAINTENANCE INSTRUCTIONS LS0513 INTRODUCTION Thank you
Pressure relief valve
Pressure relief valve Operating manual Series DHV 712 Version BA-2015.10.20 EN Print-No. 300 510 TR MA DE Rev001 ASV Stübbe GmbH & Co. KG Hollwieser Straße 5 32602 Vlotho Germany Phone: +49 (0) 5733-799-0
Installation, Operation, and Maintenance Manual
Industrial Process Installation, Operation, and Maintenance Manual Series PBFV Plastic Lined Butterfly Valve - Lug and Wafer Style Table of Contents Table of Contents Introduction and Safety...2 Safety
Type Operating Instructions. Bedienungsanleitung Manuel d utilisation
Globe control valve, pneumatically operated Actuator sizes 40 mm - 125 mm, Nominal diameter DN10-65 Kolbengesteuertes Geradsitzventil Antriebsgrößen 40 mm - 125 mm, Nennweiten DN10-65 Vanne à siège droit
Operating instructions. sonnenprotect for operators. KD-337 Part no Version X00.
Operating instructions for operators sonnenprotect 1300 KD-337 Part no. 22010 Version X00 info@sonnenbatterie.de www.sonnenbatterie.de EN IMPORTANT Read this documentation carefully before operation. Retain
Operating manual GA 250AL GA 400AL. Edition 07 / Automatic Airless Spraygun. II 2GX (Atex 95)
Operating manual GA 250AL GA 400AL Edition 07 / 2005 Automatic Airless Spraygun II 2GX (Atex 95) Contents 1 ABOUT THESE INSTRUCTIONS 5 1.1 Languages 5 1.2 Warnings, notes and symbols in these instructions
Heavy Duty Sprayer Owners Manual Model MS-O
Heavy Duty Sprayer Owners Manual Model MS-O Table of Contents Warranty 4 Warning 5 Assembly and Preparation 6 Operation 7 Cleaning and Storage 7 Standard Spray Gun & Parts List 8 Trigger Style Spray Gun
RediCoat by Nordson. Hopper and VBF Dolly Systems. Customer Product Manual Part A Issued 10/07
RediCoat by Nordson Hopper and VBF Dolly Systems Customer Product Manual Part 1082648A Issued 10/07 This document is subject to change without notice. Nordson Corporation Amherst, Ohio USA 2 Table of Contents
These installation and maintenance instructions must be read in full and completely understood before the installation!
These installation and maintenance instructions must be read in full and completely understood before the installation! 1. General information on the installation and maintenance instructions These instructions
TRICKLE CHARGER MODEL NO: ATC12VB OPERATION & MAINTENANCE INSTRUCTIONS PART NO: ORIGINAL INSTRUCTIONS LS0618 ISS 2
TRICKLE CHARGER MODEL NO: ATC12VB PART NO: 6266012 OPERATION & MAINTENANCE INSTRUCTIONS ORIGINAL INSTRUCTIONS LS0618 ISS 2 INTRODUCTION Thank you for selecting this Clarke Trickle Charger. Read this manual
Swing Piston Compressors and Vacuum Pumps
Swing Piston Compressors and Vacuum Pumps NPK 050 NPK 0100 Operating and Installation Instructions Read and observe these Operating and Installation Instructions! KNF Neuberger GmbH Alter Weg 3 D-79112
Operating Instructions
Operating Instructions BE2700 Brinkmann Immersions pumps of the series TA/STA/TAL/SAL901... 1303 Contents 1 General...1 2 Safety...2 3 Transport and storage...2 4 Description of product and accessories...2
Installation manual ACO Mains operated drain doser (MODD) for Grease Traps
Installation manual ACO Mains operated drain doser (MODD) for Grease Traps Installation manual Installation manual - ACO Mains operated drain doser (MODD) for Grease Traps Safety Notes IMPORTANT: Please
PowerPlex 40V MAX Standard Battery Pack/Charger
Form No. 3417-974 Rev C PowerPlex 40V MAX Standard Battery Pack/Charger Model No. 88540 Serial No. 318000001 and Up Model No. 88541 Serial No. 318000001 and Up Model No. 88542 Serial No. 318000001 and
Mod: KLD6-12/35XLAS-N
12/2011 Mod: KLD6-12/35XLAS-N Production code: 1914070 INSTRUCTION MANUAL LOGIC LINE PLUS HOOD Reseller Stamp for Warranty Dear customer, Above all, thank you for choosing our product and we would like
Pump Operating and Maintenance Manual - Models
Pump Operating and Maintenance Manual - Models 78-00111 - 78-0057 Thank you for purchasing the SDI Diaphragm Pump manufactured by Comet Pump. Comet produces quality products which are safe, efficient and
original operating manual Operating manual Translation of the Item-No.: ,
Translation of the original operating manual Operating manual Item-No.: 015 431 551, 015 431 581 Important! Copyright The operating manual is always to be read before commissioning the equipment. No warranty
Swing Piston Compressors and Vacuum Pumps
Swing Piston Compressors and Vacuum Pumps NPK 018 AC Pressure NPK 018 DC Pressure NPK 018 AC Vacuum NPK 018 DC Vacuum Operating and Installation Instructions Read and observe these Operating and Installation
User manual Pipe notcher Type: AL 1-2E
User manual Pipe notcher Type: AL 1-2E Page 1 of 27 Table of contents 1. Foreword... 4 1.1. Name of machine... 4 1.2. Warning... 4 1.3. Target group for each chapter... 4 1.4. Symbols... 4 1.5. Re-ordering
User Guide. Lubricus Lubrication System LUB-D1/LUB-D2/LUB-D3/LUB-D4 (24 VDC)
User Guide Lubricus Lubrication System LUB-D1/LUB-D2/LUB-D3/LUB-D4 (24 VDC) version 04/2013 Content General Information 3 Warning 3 Scope of Supply 3 Overview 3 General safety details 4 Intended use 4
Datasheet MATRE Foam Inductors. Datasheet for MATRE Foam Inductors. 1 Contents
Datasheet for MATRE Foam Inductors 1 Contents 2 General product description... 3 3 General installation guide... 3 4 Product dimensions and performance... 3 4.1 Standard bronze housing design - threaded...4
PRODUCT MANUAL. Heavy Duty Shoulder Sprayer 5L & 8L
PRODUCT MANUAL SUPERIOR PERFORMANCE Heavy Duty Shoulder Sprayer 5L & 8L Contents E A B I H F D C G A. Pump Handle with lance holder B. Safety Valve C. Spray Bottle D. Pump Assembly E. Stainless steel lance
Installation manual portable distributors
EN Installation manual portable distributors EN 60003206 Issue 11.2016 15/11/2016 Table of contents 1 About this manual 3 1.1 Structure of the warnings 3 1.2 Symbols used 4 1.3 Signal words used 4 2 Intended
Micro Diaphragm Gas Sampling Pumps
Operating and Installation Instructions Micro Diaphragm Gas Sampling Pumps Type range: NMP830K_DC-M HP NMP830.1.2K_DC-M HP NMP830K_DC-B HP NMP830.1.2K_DC-B HP NMP830K_DC-B4 HP NMP830.1.2K_DC-B4 HP You
VANDAL RESISTANT FITTINGS VR105, VR125, VR145 (VR106, VR115 Export only) PRODUCT MANUAL IMPORTANT
VANDAL RESISTANT FITTINGS VR105, VR125, VR145 (VR106, VR115 Export only) PRODUCT MANUAL SHOWER FITTINGS IMPORTANT Installer: This Manual is the property of the customer and must be retained with the product
Off-line filter system
Off-line filter system 30 NFF2, 50 NFF2, 80 NFF2 RE 51433-B/04.10 Replaces: -.- English Operating instructions The data specified above only serve to describe the product. No statements concerning a certain
Fuel Tank Sweeper #9049 OPERATOR S MANUAL
Fuel Tank Sweeper #9049 OPERATOR S MANUAL Innovative Products of America Incorporated 888-786-7899 www.ipatools.com 234 Tinker Street, Woodstock, NY 12498 DO NOT USE WITH GASOLINE! Transfers, filters and
WA 2719 ( 604 ) ( 604 ) , H.E.R.O.
a division of Middlefield Bancorp Limited 2719 Lake City Way, Burnaby, B.C., Canada Phone: ( 604 ) 420-6543 Fax: ( 604 ) 420-8725 Toll Free: 1-800-494-4376 E-mail: sales@hero.ca Website: www.hero.ca U.S.
Assembly and Maintenance Manual Type ASNU
Assembly and Maintenance Manual Type ASNU Hatschekstr.36 69126 Heidelberg Germany Tel +49(0)6221 30470 Fax +49(0)6221 304731 info@stieber.de www.stieber.de Date of issue: 30.05.2018 GB Revision: 0 U:\EngUsers\!ProduktDoku\1AAA_Einbauerklaerung_Wartungsanleitung_Konformitaetserklaerung\1AAA_Wartungsanleitungen\Orginal_Worddatei\_ASNU.docx
Type 3320, Service Manual. Serviceanleitung Service Manuel
Electromotive 2/2-way valve Elektromotorisches 2/2-Wege-Ventil Vanne électromotorisée à 2/2 voies Service Manual Serviceanleitung Service Manuel We reserve the right to make technical changes without notice.
DIAPHRAGM PUMPS: Instruction Manual
INTRODUCTION DIAPHRAGM PUMPS: Instruction Manual Congratulations for choosing a product Imovilli Pompe, the result of a careful manufacturing process supported by over fifty years of specific experience
Operating Instructions: Hand-operated, PTFE-lined butterfly valves, Series 22/23
0 Introduction These instructions are intended to assist users of BRAY PTFE-lined butterfly valves, Series 22/23 in fitting, operating and servicing valves. Risks may arise and the manufacturer's warranty
Cordless Rechargeable Saw Instructions for Use
Technical data Voltage: DC 10.8V Weight: 1.25Kg Stroke rate: 0-2100/min Stroke: 15mm Cutting capacity: max diameter in wood 80mm / in soft metal 7mm Charging time: Between 5.0-5.5 Hours Battery: 1.3Ah
Battery Charger JCB-FCH20LI2
Safety and operating manual Battery Charger JCB-FCH20LI2 ORIGINAL INSTRUCTIONS SAFETY INSTRUCTIONS WARNING: Read all safety warnings and all instructions.failure to follow the warnings and instructions
Operating Manual. Automatic spray gun AGR-09 mini, AGR-09 mini with needle stroke limitation for low-pressure atomization
Operating Manual Automatic spray gun AGR-09 mini, AGR-09 mini with needle stroke limitation for low-pressure atomization Product No.: S-AGR09GB (Original) Issue: 07/18-2 REITER GmbH + Co. KG Oberflächentechnik
PRESSURE BOOSTER 150
PRESSURE BOOSTER 150 Owners Manual! WARNING This equipment must be installed and serviced by a qualified technician. Improper installation can create electrical hazards which could result in property damage,
Type S030. Operating Instructions. Symbols used. INLINE fitting. Bedienungsanleitung Manuel d'utilisation
Type S030 INLINE fitting We reserve the right to make technical changes without notice. Technische Änderungen vorbehalten. Sous réserve de modifications techniques. Operating Instructions Bedienungsanleitung
ASSEMBLY AND OPERATING INSTRUCTION MANUAL
www.rainmakersprayers.com ASSEMBLY AND OPERATING INSTRUCTION MANUAL 18 VOLT LITHIUM ION BACKPACK SPRAYER-4 GALLON Product# 708910 Front View Back View Please read this manual for instructions and precautions
Cetane Maintenance. Dan Bemis Dresser Waukesha
Cetane Maintenance Dan Bemis Dresser Waukesha Cetane Maintenance General Hand wheel Maintenance Injection Nozzle Maintenance What is the Hand wheel Assembly Used For? Mechanism used for adjusting the compression
Assembly and Maintenance Manual Type AS
Assembly and Maintenance Manual Type AS Hatschekstr.36 69126 Heidelberg Germany Tel +49(0)6221 30470 Fax +49(0)6221 304731 info@stieber.de www.stieber.de Date of issue: 30.05.2018 GB Revision: 0 U:\EngUsers\!ProduktDoku\1AAA_Einbauerklaerung_Wartungsanleitung_Konformitaetserklaerung\1AAA_Wartungsanleitungen\Orginal_Worddatei\_AS.docx
720W PORTABLE GENERATOR
720W PORTABLE GENERATOR MODEL NO: G720 PART NO: 8857800 OPERATION & MAINTENANCE INSTRUCTIONS LS0214 INTRODUCTION Thank you for purchasing this CLARKE 720W Portable Generator Before attempting to use this
PRODUCT MANUAL. Backpack Sprayer 12L
PRODUCT MANUAL Backpack Sprayer 12L Contents D A E B I H F C G A. Pump lever brace B. Pump lever with lance holder C. Spray Bottle D. Pump Assembly E. Extendable fibreglass lance with three nozzle options
Rolling Door Opener INSTALLATION INSTRUCTION AND OWNERS MANUAL
Rolling Door Opener INSTALLATION INSTRUCTION AND OWNERS MANUAL IMPORTANT SAFETY INFORMATION FAILURE TO COMPLY WITH THE FOLLOWING SAFETY RECOMMENDATIONS MAY RESULT IN SERIOUS PERSONAL INJURY, DEATH AND
CO 3-WAY PNEUMATIC VALVE INSTRUCTION MANUAL 2080
CO 3-WAY PNEUMATIC VALVE INSTRUCTION MANUAL 2080 STI S.r.l has taken every care in collecting and verifying the documentation contained in this Instruction Manual. The information herein contained are
Quickdraw. Model 2400 Series. Operating Instructions & Maintenance Manual. Clearing The Airway Is Our #1 Priority
Quickdraw Model 2400 Series Clearing The Airway Is Our #1 Priority Operating Instructions & Maintenance Manual, INC. 11064 Randall Street Sun Valley, CA 91352 USA www.sscor.com Email: marketing@sscor.com
Flowmeter Ultrasonic Flow Metering / Dosing Device. Operating Manual
Flowmeter Ultrasonic Flow Metering / Dosing Device Operating Manual Read the user's manual carefully before starting to use the unit or software. Producer reserves the right to implement changes without
OPERATION & MAINTENANCE INSTRUCTIONS
AUTOMATIC BATTERY CHARGER / MAINTAINER MODEL NO: CBO9-12 PART NO: 6267025 OPERATION & MAINTENANCE INSTRUCTIONS LS0315 INTRODUCTION Thank you for purchasing this CLARKE product. Before attempting to use
Neotecha SAPRO Sampling Valve SV for sampling with piston syringes Installation and Maintenance Instructions
Before installation these instructions must be fully read and understood 1.1 Validity of the installation and maintenance instructions These installation and maintenance instructions are valid for all
GB Operating instructions Automatic spray gun RA 6 T-Dok-685-GB-Rev.1 200-0392 200-0393 200-0394 200-0395 200-0322 Translation of the original operating instructions Thank you for selecting a Krautzberger
VADA - V60-J PRODUCT OVERVIEW CONSTRUCTION MOTOR USAGE LIMITATIONS WARRANTY
PRODUCT OVERVIEW The VADA series of self priming jet pumps combine the functional benefits of centrifugal pumps and the practical and qualitative benefits of self-priming pumps. The Venturi system the
Instruction manual. Electrobloc EBL 269
Instruction manual 0 Manual Electrobloc EBL 69 Electrobloc EBL 69 Table of contents Introduction.......................................... Safety information..................................... Description
50 Gallon Skid Sprayer
50 Gallon Skid Sprayer Model #: KS50P5 User Manual Read this manual for complete instructions Model #: KS50P5 Table of Contents Warranty... 3 General Safety Information... 3 Hazardous Substance Alert...
Operating Manual for FINE-SPRAY gun W 3/FZ-Duo
Operating Manual for FINE-SPRAY gun W 3/FZ-Duo Read this manual carefully before installing, operating or servicing this spray gun. Keep always handy for further use. 1 Introduction The FINE-SPRAY gun
1200W INVERTER GENERATOR
1200W INVERTER GENERATOR MODEL NO: IG1200 PART NO: 8877070 OPERATION & MAINTENANCE INSTRUCTIONS LS0117 INTRODUCTION Thank you for purchasing this CLARKE 1200W Inverter Generator. Before attempting to use
PNEUMATIC PUMP Series
PNEUMATIC PUMP Series 3103... User and Maintenance Manual Original text translation TABLE OF CONTENTS 1. INTRODUCTION 2. GENERAL DESCRIPTION 3. PRODUCT-MACHINE IDENTIFICATION 4. TECHNICAL CHARACTERISTICS
Design Features: User Manual. 1. PFC function. 2. LCD remote control. 3. Battery temperature sensor function.
User Manual Design Features: 1. PFC function. except BC-1215HT / BC-2407HT 2. LCD remote control. BC-1215HT / BC-2407HT 3. Battery temperature sensor function. 4. Tri-LED color indicator for different
PRODUCT MANUAL. Heavy Duty Backpack Sprayer 16L
PRODUCT MANUAL SUPERIOR PERFORMANCE Heavy Duty Backpack Sprayer 16L Contents A D E B I H F C G A. Pump lever brace B. Pump lever with lance holder C. Spray Bottle D. Pump Assembly E. Telescopic stainless
POWERWASHER OPERATING & MAINTENANCE INSTRUCTIONS. Models: PLS130AB & PLS130AH - PLS200AB & PLS200AH DLS200AL & PLS160AH
POWERWASHER Models: PLS130AB & PLS130AH - PLS200AB & PLS200AH DLS200AL & PLS160AH OPERATING & MAINTENANCE INSTRUCTIONS 0108 CONTENTS Guarantee... 3 Specifications... 3 Safety Precautions... 4 Features...
Operating manual Separator
Operating manual Separator Sheet no. AS/4.1.141.1.1 issue 20.08.2014 Contents Section Title Page 0 Introduction... 1 1 Intended use......1 2 Marking of the fitting... 1 3 Safety instructions... 2 4 Transport
WheelieSafe. WheelieSafe. User Manual. Motorized Trolley. Distributor:
WheelieSafe Motorized Trolley WheelieSafe Distributor: User Manual You must read this manual before using your WheelieSafe trolley P/N: 9023100 Rev. 01/16 Table of contents Contents Pages Safety Symbols,
SP0 & SP1 Knapsack Sprayer
SP0 & SP1 Knapsack Sprayer We would like to congratulate you on the purchase of your new SP0. The sprayer that allows you the easiest, most comfortable way of carrying out your farm, garden, etc. projects
CHAPTER 2: ELECTRICAL SAFETY
CHAPTER 2: ELECTRICAL SAFETY 2.1 Physiological Effect of Electricity 2.2 Macroshock and Microshock Macroshock Microshock 2.3 Approaches toward Protection against Shock 2.4 Medical Safety Test Electrical
Multi-Mover Charger for model L25
Multi-Mover Charger for model L25 Important safety instruction. Keep these instructions. This manual contains important instructions for the safety of the user and the operation of the device. 1. SYMBOLS
Pump Manual. Model Numbers: SP240VDFS57LPM SP240VDFS80LPM. Product Names: Digital Refueling Station - 57 L/min Digital Refueling Station - 80 L/min
Pump Manual Model Numbers: SP240VDFS57LPM SP240VDFS80LPM Product Names: Digital Refueling Station - 57 L/min Digital Refueling Station - 80 L/min Copyright: Scintex Fuel Depot 2012[Type text] Page 1 WARNING:
12V CONSTANT PRESSURE PUMP
WHAT S IN THE BOX PRESSURE PUMP 700 L/H FLOW INSTRUCTION MANUAL 12V Pressure Pump 6m Coiled Hose SPECIFICATIONS Voltage: 12V DC Max. Current: 6Amp Max. Pressure: 70psi (4.8bar) Max. Flow Rate: 700 litres/hour
MODEL: AG-HA-950D GENERATOR OWNER S MANUAL
MODEL: AG-HA-950D GENERATOR OWNER S MANUAL BEFORE OPERATING THIS MACHINE PLEASE READ THESE INSTRUCTIONS CAREFULLY (I)WARNING 1. Read the operator s instruction manual. 2. Attention! Exhaust gases are toxic.