Hilti, Inc South 122 nd East Avenue Tulsa, OK

Transcription

1 Attached are page(s) from the 200 Hilti North American Product Technical Guide. For complete details on this product, including data development, product specifications, general suitability, installation, corrosion, and spacing & edge distance guidelines, please refer to the Technical Guide, or contact Hilti. Hilti, Inc South 122 nd East Avenue Tulsa, OK

2 Hilti Product Technical Guide P R O F I S PROFIS: The World s Most Powerful Anchor Design Software Easy to Learn Start working in just minutes Fast and Powerful Produce detailed designs quickly Specify with Confidence The largest number of approvals and latest design codes No charge. Download now at or Firestop Systems When it comes to Life Safety and building code compliance, Hilti provides complete solutions with a wide range of products and unmatched technical support. Firestop Systems Guides - Through Penetrations - Joint Penetrations FACT Program FS 411 BASIC Training Engineering Judgements Firestop Design Center online at or Hilti Diaphragm Deck Design The Hilti Diaphragm Deck Design Program allows designers to quickly and accurately design roof deck and composite floor deck diaphragms. Ability to design with innovative Hilti fasteners for frame and sidelap connection Creates easy to use load tables with span ranges based on user input Allows for different safety factors depending on load type, building code and field quality control Direct link to Hilti website Hilti Online Technical Library Design Centers Interactive Product Advisors Full-line Product Catalog Online Ordering Maps to Hilti locations Contact Us program to answer your questions MI Industrial Pipe Support Technical Guide A guide to specifying the Hilti modular pipe support system for medium to heavy loads without welding. MI System is the ideal solution for pipes up to 24 in. diameter Reliable fastenings without welds Easily installed Hilti, Inc. (US) I en español I Hilti (Canada) Corp I I Product Technical Guide 2008

3 Deck Fasteners for Attachment to Bar Joist Product Description The Hilti bar joist deck fastening system consists of a variety of powder-actuated tools which are primarily used with the following fasteners: the X-EDN19 THQ12 and the X-EDNK22 THQ12, which are available in a collated version. For many bar joist decking jobs, the tool of choice will be the DX 860-HSN tool. This self-contained stand up decking tool is powered by 0.27 caliber short cartridges, which are loaded into the tool in strips of 40. The cartridges drive the X-EDN19 or X-EDNK22 MX fasteners into almost any type of steel deck profile and base steel thicknesses of 1/8" to 3/8". These fasteners are available in collated strips of 10. Four of these strips are loaded into the DX 860-HSN tool along with the strips of cartridges, and enable the operator to fasten at a rate of up to 1,000 quality fastenings per hour. Additionally, this tool offers punch through resistance in cases where the base material is inadvertently missed. Other tools include the hand held DX-460 MX SM, a semi-automatic magazine tool for use on smaller jobs Product Description Material Specifications Technical Data Ordering Information X-EDN19 THQ12 X-EDNK22 THQ Material Specifications Listings/Approvals Fastener Fastener Fastener Nominal Fastener Designation Material Plating Hardness X-EDN 19 THQ12 Carbon Steel 5 µm Zinc1 55 HRC X-EDNK22 THQ 12 Carbon Steel 5 µm Zinc1 55 HRC 1 ASTM B 633, SC 1, Type III Technical Data Allowable Pullout Loads for Attachments to Steel Base Material lb (kn) 1, 2, 3 Fastener 1 These values represent testing performed in ASTM A 36 plate steel. Performance values in a different grade, condition or shape of base material may provide different values. 2 The values must be compared with allowable tensile pullover values. 3 Allowable values based on safety factor of Outside of recommended base material thickness range for roof and floor diaphragm applications. Allowable Pullover and Shear Loads for Attaching Steel Deck 3,4,5 ICC-ES (International Code Council) ESR-2197, ESR-2199, ESR-1414, ER-2078P COLA (City of Los Angeles) RR FM (Factory Mutual) For attaching Class 1 Steel Roof Decks with 1-60 and 1-90 wind uplift ratings. Listed for higher wind uplift ratings with FM Approved Lightweight Insulating Concrete Roof Deck Assemblies. Refer to FM RoofNav for specific assembly listings. UL (Underwriters Laboratories) Fasteners for attaching steel roof deck (uplift and fire classification) Steel Deck Gauge (in.) Fastener 16 (0.0598) 18 (0.0474) 20 (0.0358) 22 (0.0295) 24 (0.0239) 26 (0.0179) Tension Shear Tension Shear Tension Shear Tension Shear Tension Shear Tension Shear lb (kn) lb (kn) lb (kn) lb (kn) lb (kn) lb (kn) lb (kn) lb (kn) lb (kn) lb (kn) lb (kn) lb (kn) X-EDN19 THQ X-EDNK22 THQ12 2 (2.71) (2.60) (2.36) (2.09) (1.85) (1.60) (1.07) (1.33) (0.87) (1.09) (0.62) (0.82) 1 For base steel thickness 1/8" to 1/4". 2 For base steel thickness 3/16" to 3/8". 3 Allowable values are based on a safety factor of 5.0. Base Material Thickness (in.) 1/8 3/16 1/4 3/8 1/2 X-EDN19 THQ (1.89) 515 (2.29) 630 (2.80) 405 (1.80) 4 X-EDNK22 THQ (1.76) 590 (2.62) 610 (2.71) 4 4 For alternate pullover capacities and factors of safety for uplift, refer to SDI Diaphragm Design Manual. 5 Loads based on ASTM A 1008, or minimum ASTM A 653 SQ33 steel deck. Shear Strength (Q f ) and Flexibility Factor (S f ) for Calculating Steel Deck Diaphragm Strength and Stiffness1, 2, 3 1 Fastener Term Steel Deck Gauge (in.) 16 (0.0598) 18 (0.0474) 20 (0.0358) 22 (0.0295) 24 (0.0239) Q f X-EDN19& lb (kn) (13.01) (10.45) (7.98) (6.67) (5.40) X-EDNK22 S f in./kip (mm/kn) (0.0294) (0.0329) (0.0381) (0.0421) (0.0468) This data can be used to calculate fastener performance when attaching steel deck diaphragms based on SDI Diaphragm Design Manual. 2 Values based on ASTM A 1008 or minimum ASTM A653 SQ33 steel deck. 3 Profis DF software is available to generate diaphragm tables in accordance with SDI equations. A free download is available at Hilti, Inc. (US) I en español I Hilti (Canada) Corp I I Product Technical Guide

4 3.4.2 Deck Fasteners for Attachment to Bar Joist Diaphragm Tables for Standard 1.5" Deck X-EDNK22 or X-EDN19 (Pattern: 36/7) Bar Joist1, 2 Frame Fastening: Hilti X-EDNK22 / X-EDN19 Pattern: 36/7 Fastening: #10 Drill Screws Safety Factor: /7 GAUGE: 22 t = design thickness = " per span K Dwr = 129 Dir = 226 Dnr = 356 K2 = 870 GAUGE: 20 t = design thickness = " per span K Dwr = 97 Dir = 169 Dnr = 266 K2 = 1056 GAUGE: 18 t = design thickness = " per span K Dwr = 63 Dir = 111 Dnr = 175 K2 = 1398 G' = Additional tables can be generated from the Hilti Profis DF software which is available for download at For detailed information contact Hilti Tech Support K Dxx/span + 3 x K1 x span Where K1 = Refer to table for values; span in feet (ft) 1 Allowable diaphragm shear loads shown are calculated in accordance with SDI equations with safety factor of 2.35 for wind loads. 2 To calculate ASD values for load combinations involving earthquake, multiply values in table by 2.35 and divide by a safety factor of To calculate LRFD values, multiply values in table by 2.35 and multiply again by φ=0.7 for wind or φ=0.65 for earthquake. 4 At diaphragm perimeter: X-EDN19 / X-EDNK22 frame fasteners should be spaced at identical spacing as sidelap connectors. 5 Panel buckling has been checked. Dwr For Wide Rib Deck K1 Fastener Flexibility Factor K t G' Diaphragm Shear Stiffness Dxx Dwr, Dir, or Dnr (whichever is applicable) 98 Hilti, Inc. (US) I en español I Hilti (Canada) Corp I I Product Technical Guide 2008

5 Deck Fasteners for Attachment to Bar Joist Diaphragm Tables for Standard 1.5" Deck Hilti X-EDNK22 or X-EDN19 (Pattern: 36/4) Bar Joist1, 2 Frame Fastening: Hilti X-EDNK22 / X-EDN19 Pattern: 36/4 Fastening: #10 Drill Screws Safety Factor: /4 GAUGE: 22 t = design thickness = " per span K DWR = 1072 DIR = 1216 DNR = 1282 K2 = 870 GAUGE: 20 t = design thickness = " per span K DWR = 802 DIR = 909 DNR = 959 K2 = 1056 GAUGE: 18 t = design thickness = " per span K DWR = 526 DIR = 597 DNR = 630 K2 = 1398 G' = K Dxx/span + 3 x K1 x span Where K1 = Refer to table for values; span in feet (ft) 1 Allowable diaphragm shear loads shown are calculated in accordance with SDI equations with safety factor of 2.35 for wind loads. 2 To calculate ASD values for load combinations involving earthquake, multiply values in table by 2.35 and divide by a safety factor of Additional tables can be generated from the Hilti Profis DF software which is available for download at For detailed information contact Hilti Tech Support To calculate LRFD values, multiply values in table by 2.35 and multiply again by φ=0.7 for wind or φ=0.65 for earthquake. 4 At diaphragm perimeter: X-EDN19 / X-EDNK22 frame fasteners should be spaced at identical spacing as sidelap connectors. 5 Panel buckling has been checked. Dwr For Wide Rib Deck K1 Fastener Flexibility Factor K t G' Diaphragm Shear Stiffness Dxx Dwr, Dir, or Dnr (whichever is applicable) Hilti, Inc. (US) I en español I Hilti (Canada) Corp I I Product Technical Guide

6 3.4.2 Decking Fasteners for Attachment to Bar Joist Limit States Design-Factored Resistance Diaphragm Tables for Deck Fasteners (Canada) Diaphragm Table 36-7 Limit States Design (LSD)-Factored Resistance Diaphragm Shear, q, (N/mm) and Flexibility Factor, F, (mm x 10-6/N) for 38 mm deep steel nestable deck fastened with Hilti X-EDNK22/EDN19 with screwed sidelaps (Canada only)1, 2, 3 No. of Transverse Nails per 900 mm Wide Deck Units=7 (every flute) Sidelap Connection #10 Screw at 600 mm O.C. #10 Screw at 450 mm O.C. #10 Screw at 300 mm O.C. #10 Screw at 150 mm O.C. Strength, q Flexibility Factor, F Strength, q Flexibility Factor, F Strength, q Flexibility Factor, F Strength, q Flexibility Factor, F Strength, q Flexibility Factor, F Strength, q Flexibility Factor, F Strength, q Flexibility Factor, F Diaphragm Table 36-4 Limit States Design (LSD)-Factored Resistance Diaphragm Shear, q, (N/mm) and Flexibility Factor, F, (mm x 10-6/N) for 38 mm deep steel nestable deck fastened with Hilti X-EDNK22/EDN19 with screwed sidelaps (Canada only)1, 2, 3 No. of Transverse Nails per 900 mm Wide Deck Units=4 (every other flute) Sidelap Connection #10 Screw at 600 mm O.C. #10 Screw at 450 mm O.C. #10 Screw at 300 mm O.C. #10 Screw at 150 mm O.C. Strength, q Flexibility Factor, F Strength, q Flexibility Factor, F Strength, q Flexibility Factor, F Strength, q Flexibility Factor, F Strength, q Flexibility Factor, F Strength, q Flexibility Factor, F Strength, q Flexibility Factor, F Diaphragm Table 36-7 Limit States Design (LSD)-Factored Resistance Diaphragm Shear, q, (N/mm) and Flexibility Factor, F, (mm x 10-6/N) for 38 mm deep steel deck fastened with Hilti X-EDNK22/EDN19 (Canada only)1, 2, 3 No. of Transverse Nails per 900 mm Wide Deck Units=7 (every flute) Sidelap Connection Button Punch 600 mm O.C. Button Punch 450 mm O.C. Button Punch 300 mm O.C. Button Punch 150 mm O.C. Strength, q Flexibility Factor, F Strength, q Flexibility Factor, F Strength, q Flexibility Factor, F Strength, q Flexibility Factor, F Strength, q Flexibility Factor, F Strength, q Flexibility Factor, F Strength, q Flexibility Factor, F The ratio of span of deck unit to average length of sheet is taken to be 1/3. 2 Diaphragm loads are based on steel decks having an average ultimate tensile strength of 55 ksi. 3 Values shown calculated in accordance with SDI equations using a φ factor of 0.5 for LSD for all load conditions. 100 Hilti, Inc. (US) I en español I Hilti (Canada) Corp I I Product Technical Guide 2008

7 Deck Fasteners for Attachment to Bar Joist Limit States Design-Factored Resistance Diaphragm Tables for Deck Fasteners (Canada) Diaphragm Table 36-4 Limit States Design (LSD)-Factored Resistance Diaphragm Shear, q, (N/mm) and Flexibility Factor, F, (mm x 10-6/N) for 38 mm deep steel deck fastened with Hilti X-EDNK22/EDN19 (Canada only)1, 2, 3 No. of Transverse Nails per 900 mm Wide Deck Units=4 (every other flute) Sidelap Connection Button Punch 600 mm O.C. Button Punch 450 mm O.C. Button Punch 300 mm O.C. Button Punch 150 mm O.C. Strength, q Flexibility Factor, F Strength, q Flexibility Factor, F Strength, q Flexibility Factor, F Strength, q Flexibility Factor, F Strength, q Flexibility Factor, F Strength, q Flexibility Factor, F Strength, q Flexibility Factor, F Diaphragm Table 24-5 Limit States Design (LSD)-Factored Resistance Diaphragm Shear, q, (N/mm) and Flexibility Factor, F, (mm x 10-6/N) for 75 mm deep steel deck fastened with Hilti X-EDNK22/EDN19 (Canada only)1, 2, 3 No. of Transverse Nails per 600 mm Wide Deck Units=5 (every flute) Sidelap Connection Button Punch 600 mm O.C. Button Punch 450 mm O.C. Button Punch 300 mm O.C. Button Punch 150 mm O.C. Strength, q Flexibility Factor, F Strength, q Flexibility Factor, F Strength, q Flexibility Factor, F Strength, q Flexibility Factor, F Strength, q Flexibility Factor, F Strength, q Flexibility Factor, F Strength, q Flexibility Factor, F The ratio of span of deck unit to average length of sheet is taken to be 1/3. 2 Diaphragm loads are based on steel decks having an average ultimate tensile strength of 55 ksi. 3 Values shown calculated in accordance with SDI equations using a φ factor of 0.5 for LSD for all load conditions. Hilti, Inc. (US) I en español I Hilti (Canada) Corp I I Product Technical Guide

8 3.4.2 Deck Fasteners for Attachment to Bar Joist Ordering Information DX 860-HSN Decking System Tools DX 860-HSN Stand Up Decking Tool 1 pcs DX 860-HSN Stand-Up Decking Tool Use on Demand service provides one tool for 1 pcs One Month Use one month Accessories Spare Set (HSN Piston and Brake) Piston and brake for DX 860-HSN 1 pcs Fasteners (Combos with 40-strip Cartridges) Description Base Steel Thickness Quantity X-EDN19 Bulk Fastener/Cartridge Combo 3/16 < t f 3/8 2,000 pcs X-EDN19 Pallet Fastener/Cartridge Combo 3/16 < t f 3/8 32,000 pcs X-EDNK22 Bulk Fastener/Cartridge Combo 1/8 t f < 1/4 2,000 pcs X-EDNK22 Pallet Fastener/Cartridge Combo 1/8 t f < 1/4 32,000 pcs Cartridges (Strips of 40) 0.27 Caliber Short Yellow Cartridges Heavy duty for most applications 400 pcs 0.27 Caliber Short Black Cartridges Extra-heavy for harder steel 400 pcs DX 460-SM Decking System Tools DX 460-SM Hand Held Decking Tool 1 pcs DX 460-SM Stand Up Decking Tool Includes Hand Held Tool and Stand Up Handle 1 pcs Accessories Stand Up Handle DX 460-SM DLX Converts DX 460-SM Hand Held to Stand Up 1 pcs Magazine X-SM Replacement magazine for DX 460-SM 1 pcs Piston X-AP PSM Replacement piston for DX 460-SM 1 pcs Buffer (reinforced) X-460-B Replacement buffer for DX-460-SM 1 pcs Fasteners (Combos with 10-strip Cartridges for DX 460-SM) Description Base Steel Thickness Quantity X-EDN19 Bulk Fastener/Cartridge Combo 3/16 < t f 3/8 1,000 pcs X-EDN19 Pallet Fastener/Cartridge Combo 3/16 < t f 3/8 32,000 pcs X-EDNK22 Bulk Fastener/Cartridge Combo 1/8 t f < 1/4 1,000 pcs X-EDNK22 Pallet Fastener/Cartridge Combo 1/8 t f < 1/4 32,000 pcs Cartridges (Strips of 10) 0.27 Caliber Short Red Cartridges Heavy duty for most applications 1,000 pcs 0.27 Caliber Short Black Cartridges Extra-heavy for harder steel 1,000 pcs R4X12-S Decking System Tools R4X12-S Deluxe Drive Tool 1 pcs Accessories AS2-PH13-30H (Honda Gas) 13 HP, 24.0 CFM at 175 psi Compressor 1 pcs Fasteners (Non-Combo) Description Base Steel Thickness Quantity X-EDN19 Fastener (Bulk) 3/16 < t f 3/8 2,000 pcs X-EDN19 Fastener (Pallet) 3/16 < t f 3/8 32,000 pcs X-EDNK22 Fastener (Bulk) 1/8 t f < 1/4 2,000 pcs X-EDNK22 Fastener (Pallet) 1/8 t f < 1/4 32,000 pcs X-EDNK22 Bulk Fastener/Cartridge Combo 1/8 t f < 1/4 2,000 pcs X-EDNK22 Pallet Fastener/Cartridge Combo 1/8 t f < 1/4 32,000 pcs 102 Hilti, Inc. (US) I en español I Hilti (Canada) Corp I I Product Technical Guide 2008

9 Hilti Product Technical Guide In The United Sates In Canada PAYMENT TERMS: FREIGHT: CREDIT: RETURN POLICY: WARRANTY: ACCEPTANCE OF ORDER: DOMESTIC ORIGIN: BUSINESS SIZE: PRICES: CONSENT TO JURISDICTION: INDEMNIFICATION: AUTHORIZATION: Net 30 days from date of invoice. Customer agrees to pay all costs incurred by Hilti in collecting any delinquent amounts, including attorney s fees. All sales are F.O.B. Destination with transportation allowed via Hilti designated mode. Delivery dates are estimates only. Additional charges for expedited shipments, special handling requirements, and orders below certain dollar amounts shall be the responsibility of Customer. Fuel surcharges may apply depending on market conditions. All orders sold on credit are subject to Credit Department approval. Products must be in saleable condition to qualify for return. Saleable condition is defined as unused items in original undamaged packaging and unbroken quantities and in as-new condition. All returns are subject to Hilti inspection and acceptance, and a $125 restocking charge if returned more than 90 days after invoice date. Proof of purchase is required for all returned materials. Special orders products and discontinued items are not eligible for return credit. Dated materials are only returnable in case quantity, and within 30 days after invoice date. Hilti warrants that for a period of 12 months from the date it sells a product it will, at its sole option and discretion, refund the purchase price, repair, or replace such product if it contains a defect in material or workmanship. Absence of Hilti s receipt of notification of any such defect within this 12-month period shall constitute a waiver of all claims with regard to such product. THE FOREGOING WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Hilti shall in no event be liable for, and Customer hereby agrees to indemnify Hilti against all claims related to special, direct, indirect, incidental, consequential, or any other damages arising out of or related to the sale, use, or inability to use the product. Acceptance is limited to the express terms contained herein, and terms are subject to change by Hilti without notice. Additional or different terms proposed by Customer are deemed material and are objected to and rejected, but such rejection shall not operate as a rejection of the offer unless it contains variances in the terms of the description, quantity, price or delivery schedule of the goods. Orders are not deemed accepted by Hilti unless and until it ships the associated items. Any non-domestic Hilti product will be so identified on shipping documents and invoices for customers who properly identify themselves as a federal government entity. All other customers may obtain such information by written request to Hilti, Inc., Contract Compliance, P.O. Box 21148, Tulsa, Oklahoma Hilti s Quality Department personnel are the only individuals authorized to warrant the country of origin of Hilti products. Hilti is a large business. Prices are those stated on the order, and unless otherwise noted are based on purchasing all items on the order pricing for individual products may vary for purchases of different quantities or item combinations. Hilti does not maintain most favored customer records, makes no representation with respect to same, and rejects any price warranty terms proposed by Customer. Hilti's published net price list is subject to change without notice. All transactions made pursuant hereto shall be deemed to have been made and entered into in Tulsa, Oklahoma. Any and all disputes arising directly or indirectly from such transactions shall be resolved in the courts of the County of Tulsa, State of Oklahoma, to the exclusion of any other court, and any resulting judgment may be enforced by any court having jurisdiction of such an action. All transactions shall be governed by and construed in accordance with the laws of the State of Oklahoma. Customer hereby agrees to indemnify Hilti for any costs, including attorney s fees, incurred by Hilti as a result, in whole or in part, of any violation by Customer of any Federal, State or Local statute or regulation, or of any nationally accepted standard. It shall be Customer s sole responsibility to comply with all applicable laws and regulations regarding the handling,use, transportation, or disposal of products upon taking possession of same. HILTI LEGAL DEPARTMENT PERSONNEL ARE THE ONLY INDIVIDUALS AUTHORIZED TO MODIFY THESE TERMS AND CONDITIONS, WARRANT PRODUCT SUITABILITY FOR SPECIFIC APPLICATIONS, OR EXECUTE CUSTOMER DOCUMENTS, AND ANY SUCH ACTION IS NULL AND VOID UNLESS IN WRITTEN FORM SIGNED BY SUCH INDIVIDUAL. PAYMENT TERMS: FREIGHT: CREDIT: RETURN POLICY: WARRANTY: TITLE TO PRODUCT: PRICES: INDEMNIFICATION: CHANGES: CASH SALES: QUOTATIONS: Net 30 days from date of invoice. Customer agrees to pay all costs incurred by Hilti in collecting delinquent amounts, if any, including reasonable attorney s fees. Sales are F.O.B. Destination Point with transportation allowed via Hilti designated mode. Additional charges may apply for expedited delivery, special handling requirements, and order under certain limits. A fuel surcharge may apply depending on market conditions. All orders sold on credit are subject to Credit Department approval. Product may be returned prepaid (unless otherwise authorized) to Hilti provided: i) it is returned by the original purchaser ii) it is not dated product returned more than 30 days after the original delivery date iii) it is not discontinued, clearance or special order product iv) it is unused, in original packaging and in unbroken quantities. Hilti will inspect product and, if the above requirements are satisfied, will credit to customer the original purchase price. A 15% restocking fee may apply. Other than the manufacturer s published warranty, no warranties or conditions, express or implied, written or oral, statutory or otherwise are implied. Any and all conditions and warranties implied by law or by the Sale of Goods Act or any similar statutes of any Province are hereby expressly waived. Title to product remains with Hilti until the total purchase price of product is paid. Customer agrees to pay Hilti prices set out on invoice. Customer agrees to pay taxes as indicated on invoice unless Hilti receives acceptable exemption certificates. Customer agrees to use product at own risk and to indemnify Hilti against all liabilities, including legal fees, to third parties arising out of the use or possession thereof. Hilti shall in no event be liable for special, incidental or consequential damages. Hilti sales personnel are not authorized to modify these Terms and Conditions or modify Customer s credit terms. Terms are subject to change by Hilti with reasonable notice to Customer. Payment in full is due prior to goods being released. All terms and conditions apply once customer agrees to purchase product. Quotations on special promotion products are only valid until end of promotion period. Hilti, Inc. (US) I en español I Hilti (Canada) Corp I I Product Technical Guide 2008