AVANTI INTERLOCK SYSTEM FOR LIFT FENCES. User s Manual and Installation Instructions ILS_EN_E01_R06.indd 1 11/09/2012 8:48:38

Transcription

1 AVANTI INTERLOCK SYSTEM FOR LIFT FENCES User s Manual and Installation Instructions ILS_EN_E01_R06.indd 1 11/09/2012 8:48:38

2 AVANTI INTERLOCK SYSTEM FOR LIFT FENCES User s Manual and Installation Instructions Date of publication: 1 st Edition: July 2009 Revision 6: 14/9/11 Manufacturer: Avanti Wind Systems A/S Høgevej Hillerød Denmark P: (+45) F: (+45) E: info@avanti-online.com I: 2 Sales & Service: Australia Avanti Wind Systems PTY LTD P: +61 (0) China Avanti Wind Systems P: Denmark Avanti Wind Systems A/S P: Germany Avanti Wind Systems GmbH P: +49 (0) Spain Avanti Wind Systems SL P: UK Avanti Wind Systems Limited P: USA Avanti Wind Systems,Inc P: +1 (262) ILS_EN_E01_R06.indd 2 11/09/2012 8:48:38

3 Index 1 Caution Danger User s Manual Purpose Declaration of Conformity Function Component overview Maintenance Inspection Trouble shooting Installation manual Installation at the bottom platform Installation at any intermediate platform Installation at the top platform Connection and final test Test form ILS_EN_E01_R06.indd 3 11/09/2012 8:48:38

4 1. Limited Warranty 4 Avanti Wind Systems A/S warrants that commencing from the date of shipment to the Customer and continuing for a period of the longer of 365 days thereafter, or the period set forth in the standard Avanti warranty, the Avanti Interlock System ( Product ) described in this Manual will be free from defects in material and workmanship under normal use and service when installed and operated in accordance with the provisions of this Manual. This warranty is made only to the original user of the Product. The sole and exclusive remedy and the entire liability of Avanti under this limited warranty, shall be, at the option of Avanti, a replacement of the Product (including incidental and freight charges paid by the Customer) with a similar new or reconditioned Product of equivalent value, or a refund of the purchase price if the Product is returned to Avanti, freight and insurance prepaid. The obligations of Avanti are expressly conditioned upon return of the Product in strict accordance with the return procedures of Avanti. This warranty does not apply if the Product (i) has been altered without the authorization of Avanti or its authorized representative; (ii) has not been installed, operated, repaired, or maintained in accordance with this Manual or other instructions from Avanti; (iii) has been subjected to abuse, neglect, casualty, or negligence; (iv) has been furnished by Avanti to Customer without charge; or (v) has been sold on an AS-IS basis. Except as specifically set forth in this Limited Warranty, ALL EXPRESS OR IMPLIED CONDITIONS, REPRESENTATIONS AND WARRANTIES, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OR CONDITION OF MERCHANTABILITY, FITNESS FOR A PARTIC- ULAR PURPOSE, NON-INFRINGEMENT, SATISFACTORY QUALITY, COURSE OF DEAL- ING, LAW, USAGE OR TRADE PRACTICE ARE HERBY EXCLUDED TO THE MAXIMUM EX- TENT PERMITTED BY APPLICABLE LAW AND ARE EXPRESSLY DISCLAIMED BY AVANTI. IF, PURSUANT TO ANY APPLICABLE LAW, TO THE EXTENT AN IMPLIED WARRANTY CAN- NOT BE EXCLUDED AS PROVIDED IN THIS LIMITED WARRANTY, ANY IMPLIED WARRAN- TY IS LIMITED IN TIME TO THE SAME DURA- TION AS THE EXPRESS WARRANTY PERIOD SET FORTH ABOVE. BECAUSE SOME STATES DO NOT PERMIT LIMITATIONS ON THE DURA- TION OF IMPLIED WARRANTIES, THIS MAY NOT APPLY TO A GIVEN CUSTOMER. THIS LIMITED WARRANTY GIVES CUSTOMER SPECIFIC LEGAL RIGHTS, AND CUSTOMER MAY HAVE OTHER LEGAL RIGHTS UNDER AP- PLICABLE LAWS. This disclaimer shall apply even if the express warranty fails of its essential purpose ILS_EN_E01_R06.indd 4 11/09/2012 8:48:38

5 1 Caution 2 Danger a) AVANTI Interlock system is designed to be installed on the fences of the platforms in wind turbines. The system is designed to be used in combination with the AVANTI service lift. b) This system avoids the use of the Avanti service lift if any fence with interlock is open. c) This manual always needs to be represented in language of sale. a) Working under the influence of alcohol, drugs or any medication which can interfere with the safety are also much prohibited. b) If there are any doubts to the safety of the AVANTI Interlock system, or parts of it aren t properly fixed, deformed or damaged with cracks or similar incompatible harms, it must not be used. Please contact the manufacture immediately. d) Activities at height are danger ous and may lead to severe injury or even death. Gaining an adequate apprenticeship in appropriate techniques and methods of protection is important and is your own responsibility. Users are obliged to read and understand this User Manual. Further they need to be proper equipped and instructed with the use of the necessary fall arrest equipment and emergency procedures in case of injury or sudden illness. e) Only trained and authorized personnel by Avanti are allowed to install / inspect the interlock system. Users going to install AVANTI Interlock system need to be familiar with the installation section of this manual. 5 f) It s prohibited for the user to do any modification or use non-original Avanti components when assembling AVANTI Interlock system. Re-use of demounted AVANTI Interlock system or parts is not allowed. g) Using other elements as an actuator (tools, spare keys...) in order to neutralize the interlock system is strictly forbidden. h) Any changes or other uses beyond this manual are strictly forbidden ILS_EN_E01_R06.indd 5 11/09/2012 8:48:38

6 3. User s Manual Description of the equipment 3.1 Purpose The Interlock system described in this User s Manual is a security system which avoids using the AVANTI service lift if the platform fences are not properly closed at any time. 3.2 Declaration of Conformity The manufacturer Avanti Wind Systems ApS, herewith declares that the model of the following machinery: AVANTI Interlock System in conformity with the harmonized standard: UNE-EN 1088:1996 Safety of machinery. Interlocking devices associated with guards. Principles for design and selection. Chapter 5. The interlock system is ready to be used with dual power supply (400V / 690V AC), by modifying the control box wiring configuration. The interlock system is ready to be used in one platform installations or in several platforms installation, by modifying the control box wiring configuration. 3.4 Components 1. Control box on bottom platform 2. Connection box on intermediate platform 3. Switch 4. Actuator 3.3 Function 6 The interlock system uses a system of security switches installed on the doors of fences in each platform. These switches are all in serial connection through connection boxes in each platform. The system switches off the power supply to the service lift if any protected fence is open at any time. A control box, installed at the lower platform shows (by means of a green light) that all of the doors are closed and therefore, the service lift is ready to be used ILS_EN_E01_R06.indd 6 11/09/2012 8:48:39

7 3.5 Maintenance Time (performance) Component Details Daily (user) Operation of the system Open and close the doors of the fence at the bottom platform and check the system detects it by means of the green light at the control box. Open and close doors of the fence at any platform, while lift doors are closed and lift is ready, and check the green light in the lift is switched off. Annually (expert) Switch and actuator Check the adjustment of the actuator at each platform. Adjust if necessary. Replace the switch if it doesn t detect the actuator after adjustment. Annually (expert) Electrical wires Check the state and fixation of the connection wires. Replace those where any damage were observed. 3.6 Inspection Before use Each time using the AVANTI service lift the user inspects the performance of the interlock system by opening and closing the door of the fence on the lower platform, and verifying the system detects it by means of the green light of the control box. Periodical examination A periodic examination at least every 12 months is essential for the safety of the AVANTI interlock system. The examination must be performed by a competent person from Avanti or authorized by Avanti, following the test form at the back of this manual. If any component of the AVANTI interlock system is found not OK, it must be removed / replaced by a new AVANTI component. The result of the periodic examination must be recorded in the test form ILS_EN_E01_R06.indd 7 11/09/2012 8:48:39

8 3.7 Troubleshooting All the tests and repairs of electrical components must be performed by an authorized electrician only! Danger! Unplug the power supply before opening either connection boxes or control box. Breakdown Cause Solution The service lift neither goes up nor down. All the fences are closed. Green light at the control box is off. Several platforms installation. Power supply is off. One or more fences are open. Turn on the power supply. Close fences at any platform. The service lift neither goes up nor down. Green light at the control box is off. Power supply is on. Control box not properly wired for the specific power supply. Some interlock switch fails. Modify control box connections according to the wiring diagram (default configuration). Check every switch: 1. Check the adjustment between switch and actuator, and adjust them if necessary. 2. Test or replace the defective switches or damaged actuators. Wiring connections fail. Test and repair if necessary supply cable, electrical boxes connections and wiring between connection boxes, according to the wiring diagram. 8 One platform installation. The service lift neither goes up nor down. Green light at the control box is off. Power supply is on. The fence is open. Control box not properly wired for the specific power supply. Interlock switch fails Close the fence. Modify control box connections according to the wiring diagram (new bridge is required). Check the switch: 1. Check the adjustment between switch and actuator, and adjust it if necessary. 2. Test or replace the defective switch or damaged actuator. Wiring connections fail. Test and repair if necessary supply cable, electrical boxes connections and wiring between connection boxes, according to the wiring diagram. The service lift goes up and down with a fence open. Green light at the control box is on. The switch at that fence has been neutralized with any element o spare actuator Take off the element used to neutralize the interlock system and let it know to the person responsible for the windturbine. STOP Danger! Do not use the service lift until the breakdown was repaired. Wiring connections fail. Check wiring connections according to the wiring diagram. STOP Danger! Do not use the service lift until the breakdown was repaired. The service lift goes up and down with all of the fences closed. Green light at the control box is off. The light is defective Check light and its wiring and repair or replace it ILS_EN_E01_R06.indd 8 11/09/2012 8:48:39

9 4. Installation manual Fitting instructions AVANTI Interlock system is tested and approved only to be installed on wind turbines where AVANTI service lift is installed. In case of doubt, please contact AVANTI. Please familiarize yourself with these instructions and the User s Manual before installing the Interlock System. Ensure that all specified parts are present before commencing installation. 4.1 Installation at the bottom platform 1. Install the control box on the fence, by means of 4 screws and bolts, and 8 washers M8. Holes have to be drilled on the fence if necessary. No warranty is provided against damage and injury resulting from not following this User s Manual and Installation Manual i.e. reconstruction or modification of equipment or use of non-original parts which are not approved by the manufacturer. The interlock system can be installed on different types of fences. Different parts and accessories are available depending on the fence design. Verify compliance with local regulations before installing the AVANTI Interlock System. 2. Assemble the switch to the support plate by means of 2 countersunk screws, nuts and washers M ILS_EN_E01_R06.indd 9 11/09/2012 8:48:40

10 3. Mount this assembly on the door by means of 2 screws, nuts and 4 washers M5. Holes have to be drilled on the fence if necessary. Use the oblong holes of the support plate just for adjustment. Use round holes for the final fixation. 6. Check the mechanical performance and adjust the position of the switch and actuator if necessary. 7. Connect the switch to the control box and fix the wire to the fence by means of plastic strips Assemble the actuator to its support by means of 2 countersunk screws, nuts and washers M Installation at any intermediate platform 1. Assemble the connection box to the fence by means of 2 screws, nuts and washers M4. Holes have to be drilled on the fence if necessary. 5. Mount the actuator, the spacer and the protection plate on the sliding latch of the door by means of 2 screws and 2 washers M6. 2. Assemble the switch and the actuator to the door in the same way than at the bottom platform. 3. Connect the switch to the connection box and fix the wire to the fence by means of plastic strips ILS_EN_E01_R06.indd 10 11/09/2012 8:48:41

11 4.3 Installation at the top platform 1. Assemble connection box, switch and actuator in the same way than on any intermediate platform. The connection box for the top platform is identified with a sticker TOP PLATFORM. 2. Connect the switch to the connection box and fix the wire to the fence by means of plastic strips. SWITCH CONNECTION WIRE TO THE UPPER PLATFORM CONNECTION WIRE TO THE LOWER PLATFORM 4.4 Connection and final test 1. Connect all the connection boxes by means of the connection wires supplied. 2. Fix the connection wires along the tower by means of plastic strips. 3. Control box is supplied by default for 690V AC Power supply and for several platforms configuration. If any of these two characteristics changes, modify connections at the control box according to the wiring diagram supplied inside it. 4. Connect the control box to the lift and to the power supply at the bottom platform according to the wiring diagram supplied. 5. Switch on the electrical box. Check the green light at the control box is on. 6. Check the service lift doesn t work when green light is off. 7. Open and close doors on every platform to check that the system works properly, paying attention to the green light on the control box and in the lift. SWITCH CONNECTION WIRE TO THE LOWER PLATFORM 11 POWER SUPPLY POWER OUTLET CONNECTION WIRE SWITCH ILS_EN_E01_R06.indd 11 11/09/2012 8:48:42

12 Australia Avanti Wind Systems PTY LTD Unit 15 / 160 Lytton Road Morningside 4170 Queensland P: +61 (0) F: +61 (0) China Avanti Wind Systems Building 4, No 518, Gangde Road, XiaokunshanTown Songjiang District Shanghai P: F: Denmark Avanti Wind Systems A/S Høgevej Hillerød Denmark P: F: Germany Avanti Wind Systems GmbH Max-Planck-Str Elmshorn P: +49 (0) F: +49 (0) Spain Avanti Wind Systems SL Poligono Industrial Centrovia Calle Los Angeles No 88 nave La Muela P: F: UK Avanti Wind Systems Limited Caldershaw Business Centre Unit 29 Ings Lane Rochdale OL12 7LQ P: Manual, Interlock system EN 1 st Edition: July 2009 Revision 6: 14/9/11 USA Avanti Wind Systems, Inc S. Towne Drive New Berlin Wisconsin P: +1 (262) F: +1 (262) India Avanti Wind Systems India Private Ltd Indus Valley s Logistic Park Unit 3 Warehouse No. G-2 Ground Floor Vellala Street Mel Aiyanambakkam Chennai Tamil Nadu P: I: E: info@avanti-online.com ILS_EN_E01_R06.indd 16 11/09/2012 8:48:42