NBJ52SY / NB7J52SY. 2. Remove crash component from front of chassis. Remove tow bracket with nuts/bolts from drivers side. See figure 1.
|
|
- Francis Norris
- 5 years ago
- Views:
Transcription
1 NBJ52SY / NB7J52SY REPLACES: REVISED: FITTING INSTRUCTIONS JEEP CHEROKEE KJ 10/01-02/08 76mm NUDGE BAR and 76mm SERIES 2 NUDGE BAR VEHICLE FRONTAL PROTECTION SYSTEM (VFPS) FOR AIR BAG & ADR COMPLIANT VEHICLES Check installation hardware before commencing. 1. Remove bumper cover. 10/01 10/04 models: A) Remove four self- tappers along top of grille/headlight surround and remove. B) Disconnect wiring plug near left hand headlight. C) Remove six plastic clips from along top of bumper cover. D) Remove two lower plastic clips from flares and one plastic clip from bottom of flares (each side). E) Remove one plastic clip from lower inside portion of plastic inner guard (each side). F) Remove four 10mm head bolts from lower central bumper cover. G) Pull inner guard clear to access bumper cover / flare plastic clips. Three plastic clips (each side) attach flares to bumper cover. Two locks on clips must be pushed in by hand to release flare. Pull flares out and lift bumper cover off top tabs and ease bumper cover forward to access wiring. Disconnect one indicator wiring plug (each side) and one spotlight wiring plug (each side)(where fitted) and remove bumper cover. 11/04 models: A) Unclip 6 clips along top of grille/headlight surround and remove grille. B) Remove two 10mm head bolts in bumper cover, near headlight. C) Remove fog lights (if fitted). D) Remove two plastic push in/out clips and one plastic Christmas tree clip (each side) from plastic inner guards. E) Remove two 10mm head bolts from lower bumper cover. F) Unclip from flare at side and pull forward. Disconnect indicator wiring by pulling up red locking clip. Then pushing in black release clip. Repeat for other side. Slide bumper cover forward off vehicle. 2. Remove crash component from front of chassis. Remove tow bracket with nuts/bolts from drivers side. See figure Insert 3/8 x 1 ½ single bolt on plate (supplied) through large hole in chassis and drop through mounting holes. See figure Insert 3/8 x 1 ½ double bolt plate through front of chassis. See figure Install steel mounting brackets (supplied) to bolts. Use nuts/washers (supplied) FINGER TIGHTEN ONLY. See figure Align steel mounting brackets centrally on vehicle square to front of chassis. Ensure spacing is correct for protection bar to slide to inside of steel mounting brackets. TIGHTEN IN POSITION. See figure Reinstall crash components to front of chassis.. Copyright ECB Pty Ltd
2 8. 11/04- Models only: Trim out tow bracket recess areas of bumper cover. See figure 5. 9 Apply masking tape or similar to bumper cover where it is to be installed over steel mounting brackets. See figure Reinstall bumper cover over steel mounting brackets. Refit original fog lights (if required) 11. Install protection bar to inside of steel mounting brackets. For 11/04- models use four 3/8 x 1 ½ bolts, nuts and washers (supplied). For 10/04-10/04 use 3/8 x 1 ½ bolts/nuts/washers (supplied) for front holes. Use 3/8 x 1 ½ bolt and 3/8 nut/washers on 150mm wire (supplied) for rear holes. Use socket through hole in towing bracket. See figures 7 and 8. FINGER TIGHTEN ONLY. 12. Align with vehicle. See front and side views figures 9-14 TIGHTEN ALL BOLTS/NUTS. NOTE: Towing points are incorporated into steel mounting brackets. These are designed to be used together via a link for straight line towing and light snatching using an elastic type snatch rope. Always take care when towing or snatching and observe safety requirements of equipment being used. ENSURE NUMBER PLATE IS CLEARLY VISABLE Note: When fitting/refitting the licence plate to the vehicle, ensure there is no obstruction to licence plate vision in accordance with local authorities. If required relocate licence plate to an alternate location. Further VFPS Notes: a) Do not attach VFPS to the vehicle using anchorages not intended for this purpose (e.g. engine mounting bolts). b) Do not use this product for any vehicle make or model, other than those specified by the VFPS manufacturer. c) Do not remove the plaque or label from the VFPS. d) Do not modify the structure of the VFPS in any way. e) No accessory or fitment should project forward of the VFPS forward profile. f) ENSURE THESE INSTRUCTIONS ARE LEFT WITH VEHICLE OWNER AND/OR OPERATOR. FITTING KIT IMPORTANT INFORMATION Periodically check bolts and nuts for correct tightness, especially if travelling on rough roads 2 Steel mounting brackets. 2 Double bolt plates. 2 Single bolt plates. 4 3/8 x 1 ½ bolts. 10 3/8 nuts. 2 3/8 nuts/washer on 150mm wire. (Not used for 11/04- models) 14 3/8 flat washers. (Only 12 used for 10/01-10/04 models) 10 3/8 spring washers. 6 Plastic push in clips. (Not used for 11/04- models). Copyright ECB Pty Ltd
3 Remove crash component Single bolt plate Large hole in chassis Double bolt plate Figure 1 Remove towing bracket and discard Figure 2 Passenger side shown Figure 3 Ensure spacing is correct for protection bar to slide on inside of steel mounting brackets and that steel mounting brackets are centred on vehicle. Figure 4 Trim here Masking tape or similar Figure 5 11/04- Models only Figure 6 10/01-10/04 model shown. Copyright ECB Pty Ltd
4 Figure 7 10/01-10/04 Model Passenger side shown Figure 8 11/04- model driver s side shown Figure 9 76mm Nudge Bar shown Figure 10 76mm Nudge Bar shown Figure 11 76mm Series 2 Nudge Bar shown Figure 12 76mm Series 2 Nudge Bar shown. Copyright ECB Pty Ltd
5 Figure 13 76mm Midi Tube shown Figure 14 76mm Midi Tube shown. Copyright ECB Pty Ltd
6 We value your comments Dear Fitter, ECB would like to know how you went with the installation of this product. We value your comment and may need to contact you to clarify some details so please complete your contact details clearly. We would appreciate if you could complete as many of the following details as possible. Your Name: Product Part No. Product Description: Your contact No. Product Invoice No. Make, model, and year of vehicle: Product Work Order No. Company your from/company product purchased from: Date of fitment: / / Was the fitting hardware supplied complete? Yes No If no what was not supplied Yes No Did the installation go well? Please provide comments Please draw diagrams if you need to. Post to Fax to Reply Paid 122 (07) PO Box 122 Margate QLD Copyright ECB Pty Ltd
7 DESPATCH CHECKLIST NBJ52SY / NB7J52SY Work Order # Finish: Transport: Due Date: O O O O 2 Steel mounting brackets. 2 Double bolt plates. 2 Single bolt plates. 1 Bolt Kit. See other side of this page for photos of all mounts Is this product the best it can be Yes / Wrapper s initials / Checker initials If NO fix before continuing All parts checked and completed by: Nut and bolts: Order control: Final wrap check: Date / / Date / / Date / /. Copyright ECB Pty Ltd
8 Angled Round holes. Copyright ECB Pty Ltd
NB6K49SY FITTING INSTRUCTIONS KIA SORENTO 63MM STANDARD NUDGE BAR VEHICLE FRONTAL PROTECTION SYSTEM (VFPS) FOR AIR BAG & ADR COMPLIANT VEHICLES
NB6K49SY FITTING INSTRUCTIONS REPLACES: 00.00.00 REVISED: 31.05.07 Check installation hardware before commencing. 1. Lift bonnet KIA SORENTO 63MM STANDARD NUDGE BAR VEHICLE FRONTAL PROTECTION SYSTEM (VFPS)
More information8IZ64SY / NB7IZ64SY FITTING INSTRUCTIONS
8IZ64SY / NB7IZ64SY FITTING INSTRUCTIONS REPLACES: 09.10.12 REVISED: 27.11.12 Check installation hardware before commencing. ISUZU DMAX 6-12 on TYPE 8 AND 76MM SERIES 2 NUDGE BAR VEHICLE FRONTAL PROTECTION
More informationNBT115SY / NB7T115SY FITTING INSTRUCTIONS
NBT115SY / NB7T115SY FITTING INSTRUCTIONS REPLACES: 22.12.09 REVISED: 08.07.10. TOYOTA PRADO 11/09on 76MM NUDGE BAR AND 76MM SERIES 2 NUDGE BAR VEHICLE FRONTAL PROTECTION SYSTEM (VFPS) FOR AIR BAG & ADR
More informationMHO57SY / NB7HO57SY / NBHO57SY FITTING INSTRUCTIONS
MHO57SY / NB7HO57SY / NBHO57SY FITTING INSTRUCTIONS REPLACES: 17.06.07 REVISED: 09.07.10 HONDA CRV 2/07on MIDI TUBE, 76mm SERIES 2 NUDGE BAR & 76mm NUDGE BAR VEHICLE FRONTAL PROTECTION SYSTEM (VFPS) FOR
More information8T92SY/ NB6T92SY / NBT92SY FITTING INSTRUCTIONS
8T92SY/ NB6T92SY / NBT92SY FITTING INSTRUCTIONS REPLACES: 05.05.05 REVISED: 28.06.10 TOYOTA HILUX 03/05-2WD & 4WD TYPE 8, 63mm SERIES 2 NUDGE BAR and 76mm NUDGE BAR VEHICLE FRONTAL PROTECTION SYSTEM (VFPS)
More information8H64SY / NB7H64SY / NHB64SY FITTING INSTRUCTIONS
8H64SY / NB7H64SY / NHB64SY FITTING INSTRUCTIONS REPLACES: 00.00.00 REVISED: 05.09.12 HOLDEN COLORADO RG 6-12 on TYPE 8, 76MM SERIES 2 NUDGE BAR AND 76MM NUDGE BAR VEHICLE FRONTAL PROTECTION SYSTEM (VFPS)
More information8SZ60SY / NB6SZ60SY / NBSZ60SY FITTING INSTRUCTIONS
8SZ60SY / NB6SZ60SY / NBSZ60SY FITTING INSTRUCTIONS REPLACES: 10.03.06 REVISED: 11.07.10 SUZUKI JIMNY 8/05- T6 (VIN 003) TYPE 8, 63mm SERIES 2 NUDGE BAR and 76mm NUDGE BAR VEHICLE FRONTAL PROTECTION SYSTEM
More information8S61SY / NB6S61SY / NB6S62SY FITTING INSTRUCTIONS
8S61SY / NB6S61SY / NB6S62SY FITTING INSTRUCTIONS REPLACES: 21.07.05 REVISED: 22.07.10 SUBARU FORESTER 06/02-6/05 TYPE 8, 63mm SERIES 2 NUDGE BAR & 63mm NUDGE BAR VEHICLE FRONTAL PROTECTION SYSTEM (VFPS)
More informationNBMB49SY REPLACES: REVISED:
NBMB49SY REPLACES: 00.00.00 REVISED: 14.03.12 FITTING INSTRUCTIONS MERCEDES VITO 02-11 ON NUDGE BAR VEHICLE FRONTAL PROTECTION SYSTEM (VFPS) FOR AIR BAG & ADR COMPLIANT VEHICLES Check installation hardware
More informationNB6MB60SY / NBMB60SY FITTING INSTRUCTIONS
NB6MB60SY / NBMB60SY FITTING INSTRUCTIONS REPLACES: 00.00.00 REVISED: 22.01.14 Check installation hardware before commencing. 1. Lift bonnet MERCEDES BENZ SPRINTER 10/13 on 63mm SERIES 2 NUDGE BAR AND
More information8MB48SY / NB6MB48SY FITTING INSTRUCTIONS
8MB48SY / NB6MB48SY FITTING INSTRUCTIONS REPLACES: 20.03.06 REVISED: 23.07.10 MERCEDES VITO 04/04 on TYPE 8 and 63mm SERIES 2 NUDGE BAR VEHICLE FRONTAL PROTECTION SYSTEM (VFPS) FOR AIR BAG & ADR COMPLIANT
More informationNBN110SY FITTING INSTRUCTIONS. NISSAN X-TRAIL 01/10 on 76mm NUDGE BAR VEHICLE FRONTAL PROTECTION SYSTEM (VFPS) FOR AIR BAG AND ADR COMPLIANT VEHICLES
NBN110SY FITTING INSTRUCTIONS REPLACES: 00.00.00 REVISED: 15.12.10 NISSAN X-TRAIL 01/10 on 76mm NUDGE BAR VEHICLE FRONTAL PROTECTION SYSTEM (VFPS) FOR AIR BAG AND ADR COMPLIANT VEHICLES Check installation
More informationNB7FI05SY / NBFI05SY FIAT DUCATO 76mm SERIES 2 NUDGE BAR and 76mm NUDGE BAR
NB7FI05SY / NBFI05SY FIAT DUCATO 76mm SERIES 2 NUDGE BAR and 76mm NUDGE BAR REPLACES: 24.07.10 REVISED: 22.01.15 To the Fitter, This instruction covers two models of this vehicle. The difference between
More informationEAIZ66SY FITTING INSTRUCTIONS
EAIZ66SY FITTING INSTRUCTIONS REPLACES: 00.00.00 REVISED: 09.10.12 Check installation hardware before commencing. 1. Lift bonnet ISUZU DMAX 6-12 on ECB ARC BAR WINCH COMPATIBLE VEHICLE FRONTAL PROTECTION
More informationEAT116SY. 5. Remove three 10mm head bolts from inner guards and pull rearward to clear bumper side.
EAT116SY REPLACES: 30.05.12 REVISED: 22.08.12 FITTING INSTRUCTIONS TOYOTA PRADO 11/09on ARC PROTECTION BAR WITH PARKING SENSORS AND HID HEADLIGHTS VEHICLE FRONTAL PROTECTION SYSTEM (VFPS) FOR AIR BAG &
More informationNBH110SY FITTING INSTRUCTIONS. VF COMMODORE 5-13 on 76mm NUDGE BAR VEHICLE FRONTAL PROTECTION SYSTEM (VFPS) FOR AIR BAG & ADR COMPLIANT VEHICLES
NBH110SY FITTING INSTRUCTIONS REPLACES: 00.00.00 REVISED: 26.11.13. Check installation hardware before commencing. 1. Lift bonnet. VF COMMODORE 5-13 on 76mm NUDGE BAR VEHICLE FRONTAL PROTECTION SYSTEM
More informationNBM111SY FITTING INSTRUCTIONS. PAJERO SPORT 01/16-76mm NUDGE BAR VEHICLE FRONTAL PROTECTION SYSTEM (VFPS) FOR AIR BAG & ADR COMPLIANT VEHICLES
NBM111SY FITTING INSTRUCTIONS REPLACES: 00.00.00 REVISED: 6.10.16 PAJERO SPORT 01/16-76mm NUDGE BAR VEHICLE FRONTAL PROTECTION SYSTEM (VFPS) FOR AIR BAG & ADR COMPLIANT VEHICLES Check installation hardware
More informationBJ74SY FITTING INSTRUCTIONS
BJ74SY FITTING INSTRUCTIONS REPLACES: 00.00.00 REVISED: 05.08.13. Check installation hardware before commencing. 1. Lift bonnet. JEEP GRAND CHEROKEE OVERLAND WK MY14 6/13on BIG TUBE PROTECTION BAR WITH
More informationBT180SY FITTING INSTRUCTIONS
BT180SY FITTING INSTRUCTIONS TOYOTA HIACE LWB 3-2014 ON BIG TUBE PROTECTION BAR VEHICLE FRONTAL PROTECTION SYSTEM (VFPS) FOR AIR BAG & ADR COMPLIANT VEHICLES REPLACES: 00.00.00 REVISED: 01.09.14. Check
More informationEAFT01SY FITTING INSTRUCTIONS FOTON TUNLAND 03/14- ARC BAR VEHICLE FRONTAL PROTECTION SYSTEM (VFPS) FOR AIR BAG & ADR COMPLIANT VEHICLES
EAFT01SY FITTING INSTRUCTIONS REPLACES: 00.00.00 REVISED: 09.03.15 Check installation hardware before commencing. 1. Lift bonnet. FOTON TUNLAND 03/14- ARC BAR VEHICLE FRONTAL PROTECTION SYSTEM (VFPS) FOR
More informationEAM109SY FITTING INSTRUCTIONS
EAM109SY FITTING INSTRUCTIONS REPLACES: 17.12.12 REVISED: 28.04.16 NX PAJERO MY15 11/14- ARC BAR PROTECTION BAR With fog lights VEHICLE FRONTAL PROTECTION SYSTEM (VFPS) FOR AIR BAG & ADR COMPLIANT VEHICLES
More informationBH128SY FITTING INSTRUCTIONS
BH128SY FITTING INSTRUCTIONS REPLACES: 00.00.00 REVISED: 07.10.16 HOLDEN CAPTIVA 1/16 on BIG TUBE BAR WITH FOG LIGHTS & SENSORS VEHICLE FRONTAL PROTECTION SYSTEM (VFPS) FOR AIR BAG & ADR COMPLIANT VEHICLES
More information8H14SY FITTING INSTRUCTIONS
8H14SY FITTING INSTRUCTIONS REPLACES: 18.07.05 REVISED: 16.07.10 VY HOLDEN ADVENTRA / CROSS 8 / UTE / S / SS / EXECUTIVE / ACCLAIM VX HOLDEN EXECUTIVE / ACCLAIM and VT HOLDEN ALL MODELS TYPE 8 VEHICLE
More informationBM141SY FITTING INSTRUCTIONS
BM141SY FITTING INSTRUCTINS REPLACES: 24.03.10 REVISED: 21.07.10. Check installation hardware before commencing. MITSUBISHI TRITN MN 08/09 on BIG TUBE PRTECTIN BAR WITH FG LIGHTS VEHICLE FRNTAL PRTECTIN
More informationEAN102SY FITTING INSTRUCTIONS
MARGATE EAN102SY FITTING INSTRUCTIONS REPLACES: 00.00.00 REVISED: 27.07.10 NISSAN PATHFINDER R51 05/10on & NAVARA D40 ST-X 05/10on WINCH COMPATIBLE (UP TO XP 9.5) ARC PROTECTION BAR WITH FOG LIGHTS VEHICLE
More informationNBF38SY FITTING INSTRUCTIONS. FORD TERRITORY 7/14on 76MM NUDGE BAR VEHICLE FRONTAL PROTECTION SYSTEM (VFPS) FOR AIR BAG & ADR COMPLIANT VEHICLES
NBF38SY FITTING INSTRUCTIONS COMMENCES: 280417 REVISED: 000000 Check installation hardware before commencing FORD TERRITORY 7/14on 76MM NUDGE BAR VEHICLE FRONTAL PROTECTION SYSTEM (VFPS) FOR AIR BAG &
More informationBJ100SY FITTING INSTRUCTIONS
BJ100SY FITTING INSTRUCTIONS REPLACES: 00.00.00 REVISED: 15.07.13. Check installation hardware before commencing. Special Tools: T15 Torx bit and required drivers. 1. Lift Bonnet JEEP WRANGLER JK 08 on
More informationNB6R56SY FITTING INSTRUCTIONS
NB6R56SY REPLACES: 00.00.00 REVISED: 01.06.10 FITTING INSTRUCTIONS LANDROVER DISCOVERY 4 10/09on SERIES 2 NUDGE BAR VEHICLE FRONTAL PROTECTION SYSTEM (VFPS) FOR AIR BAG & ADR COMPLIANT VEHICLES Check installation
More informationEAH153SY FITTING INSTRUCTIONS
EAH153SY FITTING INSTRUCTIONS REPLACES: 15.12.16 REVISED: 16.02.17 HOLDEN COLORADO 6/16on BIG TUBE WINCH PROTECTION BAR WITH FOG LIGHTS VEHICLE FRONTAL PROTECTION SYSTEM (VFPS) FOR AIR BAG & ADR COMPLIANT
More informationEAT231SY FITTING INSTRUCTIONS
EAT231SY FITTING INSTRUCTIONS REPLACES: 00.00.00 REVISED: 19.04.16. Check installation hardware before commencing 1. Lift bonnet. TOYOTA FORTUNER 5-15 ON ECB WINCH COMPATIBLE BIG TUBE with fog lights VEHICLE
More informationMMA38SY/ NB6MA38SY/ NBMA38SY
MARGATE MMA38SY/ NB6MA38SY/ NBMA38SY REPLACES: 20.08.07 REVISED: 11.07.10 FITTING INSTRUCTINS MAZDA CX-7 11/06-09/09 MIDI TUBE, SERIES 2 NUDGE BAR AND 76mm NUDGE BAR VEHICLE FRNTAL PRTECTIN SYSTEM (VFPS)
More informationBH32SY FITTING INSTRUCTIONS
BH32SY FITTING INSTRUCTINS REPLACES: 09.02.10 REVISED: 28.06.10. Check installation hardware before commencing. 1. Lift bonnet. HLDEN CAPTIVA 9/06on BIG TUBE BAR WITH FG LAMPS VEHICLE FRNTAL PRTECTIN SYSTEM
More informationEAGW10SY FITTING INSTRUCTIONS
EAGW10SY FITTING INSTRUCTINS SUPERCEEDS: EAGW04SY REVISED: 05.02.13 Check installation hardware before commencing. 1. Lift bonnet. GREAT WALL V240 03/11on AND V200 08/11on ARC BAR WITH FG LIGHTS VEHICLE
More informationEAF164SY FITTING INSTRUCTIONS
EAF164SY FITTING INSTRUCTIONS REPLACES: 00.00.00 REVISED: 16.08.16. FORD RANGER SERIES 2 and EVEREST ECB ARC BAR WITH FOG LIGHTS AND SONAR SYSTEM VEHICLE FRONTAL PROTECTION SYSTEM (VFPS) FOR AIR BAG &
More informationJAH03SY FITTING INSTRUCTIONS VT, VX AND VU HOLDEN COMMODORE ARC BAR VEHICLE FRONTAL PROTECTION SYSTEM (VFPS) FOR AIR BAG & ADR COMPLIANT VEHICLES
JAH03SY FITTING INSTRUCTINS REPLACES: 20.12.07 REVISED: 09.09.10. VT, VX AND VU HLDEN CMMDRE ARC BAR VEHICLE FRNTAL PRTECTIN SYSTEM (VFPS) FR AIR BAG & ADR CMPLIANT VEHICLES Check installation hardware
More informationBH21SY FITTING INSTRUCTIONS
BH21SY FITTING INSTRUCTINS REPLACES: 00.00.00 REVISED: 13.01.11. VE CMMDRE Series 2 MEGA AND BERLINA BIG TUBE PRTECTIN BAR WITH FG LIGHTS VEHICLE FRNTAL PRTECTIN SYSTEM (VFPS) FR AIR BAG & ADR CMPLIANT
More informationBF09SY FITTING INSTRUCTIONS
BF09SY FITTING INSTRUCTINS REPLACES: 22.02.10 REVISED: 09.07.10 FRD BA & BF FALCN & RTV BIG TUBE PRTECTIN BAR VEHICLE FRNTAL PRTECTIN SYSTEM (VFPS) FR AIR BAG AND ADR CMPLIANT VEHICLES Check installation
More informationBG41SY FITTING INSTRUCTIONS
TELEPHNE: (07) 3897 5700 FAX: (07) 3283 1168 CLNTARF, BRISBANE. P.. Box 122, BG41SY FITTING INSTRUCTINS REPLACES: 10.01.06 REVISED: 08.08.10 GMC SIERRA 9/04-2500 4X4 BIG TUBE PRTECTIN BAR T SUIT 15000Lb
More informationBH13SY FITTING INSTRUCTIONS VY SS BIG TUBE PROTECTION BAR VEHICLE FRONTAL PROTECTION SYSTEM (VFPS) FOR AIR BAG AND ADR COMPLIANT VEHICLES
CLNTARF, BRISBANE. P.. Box 122, BH13SY FITTING INSTRUCTINS REPLACES: 18.02.03 REVISED: 21.08.10 Check installation hardware before commencing. NTE: Treat all drilled holes with rust inhibitor. 1. Lift
More informationBT91S FITTING INSTRUCTIONS
BT91S FITTING INSTRUCTINS REPLACES: 27.07.04 REVISED: 22.08.10 TYTA LANDCRUSIER 70/75/78/79 SERIES BIG TUBE WITH 9000LB WARN WINCH MUNTING BRACKET PRTECTIN BAR VEHICLE FRNTAL PRTECTIN SYSTEM (VFPS) Check
More informationBT72SY / AWMT13Y FITTING INSTRUCTIONS
BT72SY / AWMT13Y FITTING INSTRUCTINS REPLACES: 16.02.10 REVISED: 15.07.10 LANDCRUSIER PRAD 7/96-2/03 9000lbWARN WINCH BIG TUBE BULLBAR (RETAINS FG LIGHTS) / WINCH MUNTING BRACKET VEHICLE FRNTAL PRTECTIN
More informationBT107SY FITTING INSTRUCTIONS
TELEPHNE: (07) 3897 5700 FAX: (07) 3283 1168 CLNTARF, BRISBANE. P.. Box 122, BT107SY FITTING INSTRUCTINS REPLACES: 22.02.10 REVISED: 11.07.10. TYTA LANDCRUISER 200 SERIES 11/07 N BIG TUBE BAR (WITH FG
More informationT15 Fleet Frontal Protection System Vehicle: Mazda BT50 09/08+ Part No. 070SB15X46Z
Australian Standards Relating to Installing Vehicle Frontal Protection Systems (VFPS): AS 4876.1-2002 a) Do not attach V.F.P.S. to vehicle using anchorages not intended for this purpose (e.g. engine mounting
More informationKJ JEEP COMBINATION BULL BAR WARNING
KJ JEEP COMBINATION BULL BAR PRODUCT NUMBER FITTING KIT NUMBER 3450120 6171962 WARNING FOR VEHICLES EQUIPPED WITH SRS AIRBAG WHEN INSTALLED IN ACCORDANCE WITH THESE INSTRUCTIONS, THE FRONT PROTECTION BAR
More informationLAND ROVER DISCOVERY 3 ARB BULL BAR AND WINCH BAR WARNING
LAND ROVER DISCOVERY 3 ARB BULL BAR AND WINCH BAR PART No 3432150 DISCOVERY 3 WINCH BAR PART No 3232150 DISCOVERY 3 BULL BAR WARNING FOR VEHICLES EQUIPPED WITH SRS AIRBAG WHEN INSTALLED IN ACCORDANCE WITH
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS PART # Product: Vehicle: 074ST17A89B FRONT BUMPER T17 Toyota TACOMA 2016 / ON (Third Gen) WARNING Read instructions completely before commencing fitment. Always use personal safety
More informationLeft and Right Bar Light L Brackets. Driver/Left Frame Bracket
PARTS LIST: 1 Bumper 14 12mm Nylon Lock Nuts 1 Bull Nose Hoop 2 10mm Double Bolt Plates 1 Winch Tray 4 10-1.5mm x 25mm Hex Bolts 1 Driver/left Frame Mounting Bracket 8 10mm x 30mm x 2.5mm Flat Washers
More informationFITTING KIT No s : BULL BAR WINCH ( P/No ) BULL BAR NON WINCH ( P/No )
ARB WINCH / NON WINCH BULL BAR TO SUIT LANDROVER DISCOVERY 2003 ONWARD. FITTING KIT No s :- 617 1793 BULL BAR WINCH ( P/No 343 2120 ) 617 1794 BULL BAR NON WINCH ( P/No 323 2120 ) WARNING FOR VEHICLES
More informationWARNING. When installed in accordance with these instructions, the front protection bar does not affect operation of the SRS airbag.
Part Number: 343870 F/Kit 17557 Product Deluxe Combination Winch and Non Winch Bull Bar Description: Suited to Nissan XTERRA 05ON USA Only vehicle/s: WARNING REGARDING VEHICLES EQUIPPED WITH SRS AIRBAG;
More informationBolt tensions Dia. (mm) Nm ft.lbs Dia. (inch) Nm ft.lbs
Product: Vehicle: FITTING INSTRUCTIONS T15 Fleet Bull Bar Nissan Pathfinder R51 / Nissan Navara D40 Part No. 070SB15F10L 070AP15F10L Australian Standards Relating to Installing Vehicle Frontal Protection
More informationT15 / T17 Frontal Protection Bar Ford Ranger / Mazda BT50 Part No. 070SB15F46Z 070AP15F46Z 074SB17N46Z
Australian Standards Relating to Installing Vehicle Frontal Protection Systems (VFPS): AS 4876.1-2002 a) Do not attach V.F.P.S. to vehicle using anchorages not intended for this purpose (e.g. engine mounting
More informationINSTALLATION INSTRUCTIONS ELEVATION FRONT BUMPER DODGE RAM
INSTALLATION INSTRUCTIONS PARTS LIST: 1 Elevation Bumper Assembly 24 12mm x 37mm OD x 3mm Flat Washers 2 Frame Mounting Brackets 12 12mm Nylon Lock Nuts 8 12-1.75mm x 50mm Hex Bolts 2 License Plate Mounting
More informationARB TOYOTA 80 SERIES REAR STEP TOW BAR
ARB TOYOTA 80 SERIES REAR STEP TOW BAR Product number: 5611010 Optional Jerry Can Carrier Optional Wheel Carrier Left Hand Side of vehicle (LHS) Rear Step Tow Bar Right Hand Side of vehicle (RHS) READ
More informationWH/WK JEEP GRAND CHEROKEE 2005 ON WARNING
Part Number: 3450130 F/KIT: 6172092 Product Description: Suited to vehicle/s: COMBINATION BULL BAR WH/WK JEEP GRAND CHEROKEE 2005 ON WARNING REGARDING VEHICLES EQUIPPED WITH SRS AIRBAG; When installed
More informationINSTALLATION GUIDE PREMIUM FRONT BUMPER FOR RAM AEV30304AA Last Updated: 09/18/17
AEV30304AA Last Updated: 09/18/17 PREMIUM FRONT BUMPER FOR RAM 1500 INSTALLATION GUIDE PLEASE READ BEFORE YOU START To guarantee a quality installation, we recommend reading these instructions thoroughly
More informationARB PRADO WINCH/NON WINCH BUMPER TO SUIT GXL, VX AND GRANDE 2003 ONWARDS.
ARB PRADO WINCH/NON WINCH BUMPER TO SUIT GXL, VX AND GRANDE 003 ONWARDS. PART No 390 500050 Top Tube Kit 50073 Buffer Kit With hole (required when fitting Top Tube) 50074 Buffer Kit With no hole FITTING
More informationINSTALLATION INSTRUCTIONS
Hardware: 12M x 40M hex head bolts Qty: 4 12M flat washers Qty: 8 12M lock washers Qty: 4 12M Ny-lock hex nuts Qty: 4 Extension bracket with bolt Qty: 2 8M Ny-lock hex nuts Qty: 2 8M Lock washer Qty: 2
More informationMITSUBISHI TRITON MQ (2015 +) AEROSTYLE 4X4 2 POST 3 POST 4 POST 5 POST
INSTALLATION GUIDE BULLBAR MITSUBISHI TRITON MQ (2015 +) AEROSTYLE 4X4 2 POST 3 POST 4 POST 5 POST Version 171010_1 PLEASE READ THE INSTALLATION GUIDE CAREFULLY BEFORE FITTING PRODUCT TO VEHICLE WHEN INSTALLED
More information07-13 GM 1500 WINCH PLATE
92108000 07-13 GM 1500 WINCH PLATE THANK YOU FOR CHOOSING ROUGH COUNTRY FOR YOUR OFF ROAD NEEDS. Rough Country recommends a certified technician install this kit. In addition to these instructions, professional
More informationSS1135HF Jeep KJ Cherokee CRDI4 2.8Litre-I4 Diesel Engine
SS1135HF Jeep KJ Cherokee CRDI4 2.8Litre-I4 Diesel Engine Parts List 23/2/2010 ITEM PART NO DESCRIPTION QTY 1 965-133-000 BODY - SNORKEL (SS1130HF) 1 2 000-135-800 3 ½" AIR RAM ASSEMBLY 1 3 965-032-000
More informationConflicts None. TOYOTA TUNDRA 2017 Black Laser Cut Grille. Part Number: Accessory Code: BG3000. General Applicability
TOYOTA TUNDRA 2017 Black Laser Cut Grille Part Number: 00016-34173 Accessory Code: BG3000 Conflicts None Kit Contents Item # Quantity Reqd. Description 1 1 Laser Cut Grille 2 1 Complete hardware kit General
More informationCOMBAR G/BAR CHEROKEE KJ SRS NFO
Part Number: 3450170 F/KIT: 6173661 & 6173668 Product Description: Suited to vehicle/s: Optional Fitting Kit: WARNING REGARDING VEHICLES EQUIPPED WITH SRS AIRBAG; When installed in accordance with these
More informationBBT020/ BBC020/ BBCD020 HOLDEN RODEO RA7 & ISUZU DMAX 07+ 2WD & 4WD Models
INSTALLATION GUIDE BBT020/ BBC020/ BBCD020 HOLDEN RODEO RA7 & ISUZU DMAX 07+ 2WD & 4WD Models Ironman 4x4 BBT/ BBC/ BBCD020 Bull Bars fit to a Holden Rodeo & Isuzu DMAX. It will take about 3 hours to install.
More informationBBT033/ BBC033/ BBCD033 TOYOTA HILUX 10/2011
INSTALLATION GUIDE BBT033/ BBC033/ BBCD033 TOYOTA HILUX 10/2011 Ironman 4x4 BBT/ BBC/ BBCD033 Bull Bars fit to a Toyota Hilux 10/2011 It will take about 3 hours to install. NOTE: This product has been
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS PART # 074ST17N22G Product: FRONT BUMPER Vehicle: FORD F250/350 SUPERDUTY 2011-2016 WARNING Read instructions completely before commencing fitment. Always use personal safety
More informationPassenger/Right Top Support Bracket. (2) 10mm Nut Plates
PARTS LIST: 1 Extreme Grille Guard 16 12mm x 32mm OD x 3mm Flat Washers 1 Driver/Left Frame Mounting Bracket 10 12mm Lock Washers 1 Passenger/Right Frame Mounting Bracket 10 12mm Hex Nuts 1 Driver/Left
More informationXX, TOYOTA, TACOMA FRONT BUMPER INSTALLATION INSTRUCTIONS THIS BUMPER SHOULD ONLY BE INSTALLED BY A PROFESSIONAL. SAFETY
FRONT BUMPER INSTALLATION INSTRUCTIONS THIS BUMPER SHOULD ONLY BE INSTALLED BY A PROFESSIONAL. SAFETY Know safety, no injury. Know injury, no safety. ~Author Unknown If there are any questions, call 1-855-HHTOUGH
More informationBULLBAR Fitting instructions to fit TUFF Range Bullbars (2-5 Post and Aerostyle) to TOYOTA FORTUNER
BULLBARS FITTING INSTRUCTIONS FOR TOYOTA FORTUNER Last updated 9/2/16 TUFF BULLBARS AUSTRALIA sales@tuffbullbars.com.au 6 Tews Ct, (PO Box 1977) marketing@tuffbullbars.com.au TOOWOOMBA QLD 4350 feedback@tuffbullbars.com.au
More informationINSTALLATION INSTRUCTIONS FORD F-150 2WD & 4WD RETAINS FACTORY TOW HOOKS PART #P3063
INSTALLATION INSTRUCTIONS FORD F-150 2WD & 4WD RETAINS FACTORY TOW HOOKS PART #P3063 PARTS LIST: 1 Grille Guard 2 10-1.5mm Nylon Lock Nuts 1 Driver/Left Frame Mounting Bracket 4 12mm Plastic Washers 1
More informationSS188HF Toyota Land Cruiser Prado 150 Series KDJ150R 3.0L 4 Cyl. D-4D Diesel (1KD-FTV Engine)
SS188HF Toyota Land Cruiser Prado 150 Series KDJ150R 3.0L 4 Cyl. D-4D Diesel (1KD-FTV Engine) Parts List 8/7/2010 ITEM PART NO. DESCRIPTION QTY 1 365-133-000 BODY - SNORKEL (SS188HF) 1 2 000-135-800 3
More information09-12 Dodge 4WD /4 Body Lift
92RC80000 09-12 Dodge 4WD 1500 1 1/4 Body Lift Thank you for choosing Rough Country for all your suspension needs. Rough Country recommends a certified technician install this kit. Attempts to install
More informationARB TOYOTA 100 SERIES IFS REAR STEP TOW BAR
ARB TOYOTA 100 SERIES IFS REAR STEP TOW BAR Product number: 5613210 Optional Jerry Can Carrier Optional Wheel Carrier Left Hand Side of vehicle (LHS) Rear Step Tow Bar Right Hand Side of vehicle (RHS)
More informationRev TOOLS & MATERIALS REQUIRED QTY 3D PART NO. DESCRIPTION
Rev. 04-10 QTY 3D PART NO. DESCRIPTION 1 691609 FRONT BUMPER REPLACEMENT 1 691610 RIGHT SIDE SKIRT 1 691611 LEFT SIDE SKIRT 1 691612 REAR LOWER SKIRT 4 3M 94 3M ADHESION PROMOTER 16 #8 X ¾ SELF DRILLING
More informationBBT007/ BBC007/ BBCD007 TOYOTA PRADO 90 Series
INSTALLATION GUIDE BBT007/ BBC007/ BBCD007 TOYOTA PRADO 90 Series Ironman 4x4 BBT/ BBC/ BBCD007 Bull Bars fit to a Toyota Prado 90 Series. It will take about 3 hours to install. NOTE: This product has
More information2015+ EcoBoost F150 & Raptor Intercooler Install
2015+ EcoBoost F150 & 2017+ Raptor Intercooler Install Note: This entire job can be performed with the truck on the ground - No need to raise the vehicle. The most difficult part is removing the grille
More informationADDICTIVE DESERT DESIGNS
Preparation: Disconnect the negative battery terminal. Park the vehicle on level ground and set the emergency brake. We recommend reading through the installation instructions in whole before performing
More informationCOMBAR G/BAR CHEROKEE KJ SRS 8/9 NFO
Part Number: 3450160. F/KIT: 6173660 & 6173667 Product Description: Suited to vehicle/s: Optional Fitting Kit: WARNING REGARDING VEHICLES EQUIPPED WITH SRS AIRBAG; When installed in accordance with these
More informationINSTALLATION GUIDE Front Bumper. KL Cherokee (Trailhawk)
INSTALLATION GUIDE Front Bumper KL Cherokee (Trailhawk) Included Hardware: Sample Sample Sample Skill Level: 5/5 stars (Professional install recommended) Disclaimer Expedition One is not responsible for
More informationJEEP GRAND CHEROKEE WK ON (EXCLUDING SRT8) INCLUDING TRAILHAWK WARNING
Part Number: 3450410 Product Description: Suited to vehicle/s: Winch install kit: Radar install kit: DELUXE BULLBAR JEEP GRAND CHEROKEE WK2 2011-2014 ON (EXCLUDING SRT8) INCLUDING TRAILHAWK 3540050 3550110
More informationINSTALLATION INSTRUCTIONS
Read instructions fully before commencing fitment. Left hand & Right hand components are determined as seated in the vehicle. Check for (& remove) any build up in all captive nuts fitted to the Bumper.
More informationWARNING. ARB 4x4 ACCESSORIES. Corporate Head Office Garden St Tel: +61 (3) Kilsyth, Victoria Fax: +61 (3) AUSTRALIA 3137
Part Numbers: Suited to vehicle/s: 3212400 - ARB BULL BAR NON-FLARED 3212410 - ARB BULL BAR FLARED 3412400 - ARB WINCH BAR NON-FLARED* 3412408 - ARB WINCH BAR NON-FLARED (EXPORT ONLY)* 3412410 - ARB WINCH
More informationSAFETY SENSORS FIELD OF VIEW WILL BE ALTERED WITH USE OF THE REPLACEMENT BUMPER. Injury hazard
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More informationSAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER.
Installation Instructions SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other
More informationIMPORTANT: PLEASE KEEP THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE! 2015 Nissan Murano. Upper and Lower Overlay Mesh Grilles
IMPORTANT: PLEASE KEEP THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE! 2015 Nissan Murano Upper and Lower Overlay Mesh Grilles Upper Chrome Mesh Part #1318-010U-15 / Lower Chrome Mesh Part #1318-010L-15
More informationLexus NX Fine Mesh and Dynamic Radar Cruise Control Fine Mesh Grilles
IMPORTANT: PLEASE KEEP THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE! 2015-16 Lexus NX Fine Mesh and Dynamic Radar Cruise Control Fine Mesh Grilles Upper Insert - factory chrome surround and emblem reused
More informationWARNING TAKE NOTE OF THE FOLLOWING: THIS PRODUCT MUST BE INSTALLED EXACTLY AS PER THESE INSTRUCTIONS USING ONLY THE HARDWARE SUPPLIED.
ARB WINCH/NONWINCH BUMPER TO SUIT TOYOTA HJ100 IFS PRODUCT No. 3913140 5100050 Top Tube Kit 5100160 Buffer Kit With hole (required when fitting Top Tube) 5100170 Buffer Kit With no hole Fitting Kit No.
More informationSS985HF Mazda BT-50 B32P Series 3.2L 5cylinder TDCi Diesel (P5AT Engine)
SS985HF Mazda BT-50 B32P Series 3.2L 5cylinder TDCi Diesel (P5AT Engine) Parts List 01/03/2013 ITEM PART NO. DESCRIPTION QTY 1 685-133-000 BODY - SNORKEL (SS985HF) 1 2 000-135-800 3 ½" AIR RAM ASSEMBLY
More informationThis SmartBar is also compatible with earlier Pajero models (01/2007+) with headlight washers LIGHT WEIGHT
Fitting Instructions - NX Pajero (09/2014+) Estimated Fitting time: 3 hrs. This SmartBar is also compatible with earlier Pajero models (01/2007+) with headlight washers FI-162 Revision: A Model No: SA162AA162
More informationSS41HF Mitsubishi Pajero NS & NT V8/V9 Series 3.2 Litre Turbo Diesel (4M41 Engine) 3.8 Litre V6 Petrol (6G76 Engine)
SS41HF Mitsubishi Pajero NS & NT V8/V9 Series 3.2 Litre Turbo Diesel (4M41 Engine) 3.8 Litre V6 Petrol (6G76 Engine) 21/7/2010 Parts List ITEM PART NO DESCRIPTION QTY 1 570-133-200 BODY - SNORKEL (SS41HF)
More informationTHANKS FOR CHOOSING TO BE TUFF!!!!!!!!!
TUFF BULLBARS AUSTRALIA, Ph: 1300 BE TUFF (1300 23 88 33) 5-7 Holt Drive, (P.O. Box 1977) Fax: 07 4633 1236 Torrington, sales@tuffbullbars.com.au Toowoomba, admin@tuffbullbars.com.au Queensland 4350, feedback@tuffbullbars.com.au
More informationBULLBAR Fitting instructions to fit TUFF Range Bullbars (2-3 Post, and Aerostyle) to NISSAN NP300 NAVARA
TUFF BULLBARS AUSTRALIA sales@tuffbullbars.com.au 6 Tews Ct, (PO Box 1977) marketing@tuffbullbars.com.au TOOWOOMBA QLD 4350 feedback@tuffbullbars.com.au Phone: 1300 BE TUFF www.tuffbullbars.com.au (1300
More informationSAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER.
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More informationARB WINCH/NON WINCH BUMPER TO SUIT MITSUBISHI PAJERO NM FLARED. EXCLUDING EXCEED MODEL WARNING
ARB WINCH/NON WINCH BUMPER TO SUIT MITSUBISHI PAJERO NM FLARED. EXCLUDING EXCEED MODEL PRODUCT No. 3934020 Sahara Bar 3034020 Sahara Bumper FITTING KIT No. 6171383, 6171762, 6171363 WARNING FOR VEHICLES
More informationSS1066HF Jeep JK Wrangler Left Hand Drive CRDI4 2.8Litre-I4 Diesel Engine and EGHV6 3.8Litre V6 Gasoline Engine
SS1066HF Jeep JK Wrangler Left Hand Drive CRDI4 2.8Litre-I4 Diesel Engine and EGHV6 3.8Litre V6 Gasoline Engine Installation Guide Safari SS1066HF Page - 1 of 12 6/10/2009 ITEM PART NO DESCRIPTION QTY
More informationNissan Titan / / Front Bumper Installation Instructions. Removal. Hardware. 12mm/1.
2004-2014 Nissan Titan 20-915-04 / 22-915-04 / 24-915-04 Front Bumper Installation Instructions Hardware 6 ½ Hex Bolts 10 ½ Lock Washers 16 ½ Flat washers 6 ½ Hex Nuts 4 12mm/1.25 x 35mm Removal 1. First,
More informationINSTALLATION INSTRUCTIONS FORD F-150 2WD & 4WD RETAINS FACTORY TOW HOOKS PART #P3063
INSTALLATION INSTRUCTIONS FORD F-150 2WD & 4WD RETAINS FACTORY TOW HOOKS PART #P3063 PARTS LIST: 1 Grille Guard 2 10-1.5mm Nylon Lock Nuts 1 Driver/Left Frame Mounting Bracket 4 12mm Plastic Washers 1
More informationINSTALLATION INSTRUCTIONS HEAVY DUTY FRONT BUMPER CHEVY SILVERADO 1500
INSTALLATION INSTRUCTIONS PARTS LIST: 1 Heavy Duty Bumper Assembly 16 12mm Nylon Lock Nuts 1 Driver Mounting Bracket 8 4mm x 10mm Socket Head Screws 1 Passenger Mounting Bracket 4 Sensor Plugs 4 Support
More informationSS175HF ISUZU D-MAX (June 2012 onwards) 3.0Litre, 4 Cylinder Turbo Diesel (4JJ1-TC Hi-Power Engine)
SS175HF ISUZU D-MAX (June 2012 onwards) 3.0Litre, 4 Cylinder Turbo Diesel (4JJ1-TC Hi-Power Engine) 01/09/2013 Parts List ITEM PART NO. DESCRIPTION QTY 1 740-133-000 BODY - SNORKEL (SS175HF) 1 2 000-135-800
More informationSAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER.
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More informationHAVING INSTALLATION QUESTIONS? CALL TECHNICAL SUPPORT AT
9/23/2009 1 of 6 ITEM 1 QTY 8 Parts List PART NUMBER DESCRIPTION 3/8" CONICAL TOOTHED WASHER TOOLS REQUIRED #2 PHILLIPS SCREWDRIVER #2 STUBBY SCREWDRIVER 8mm SOCKET 13mm SOCKET RATCHET 12" EXTENSION TORQUE
More information