Medifab AU 1300 b NZ Page 1

Transcription

1 Medifab Ltd Australia: 26 Pardoe Street, Devonport, TAS 7310 New Zealand: 32 Detroit Drive, Rolleston 7675 Call (AU) Call (NZ) Medifab AU 1300 b NZ Page 1

2 Wall Mount Change & Wash Station Table of Contents Pre-delivery and Initial Set Up... 3 Intended Use... 4 Installation Instructions... 5 Mounting to Wall... 6 Electrical Installation... 7 Electrical TIPS... 7 Operating instructions... 8 Important Points... 9 Maintenance Instructions Electrical Safety Rechargeable Battery Instructions Accessories Warranty Thoroughly read this manual before commencing installation and operation. Medifab AU Medifab NZ Page 2

3 PRE-DELIVERY AND INITIAL SET UP 1) Ensure when product arrives that there has been no transit damage, taking particular care of electrical, framework, powder coating damage and mattress damage. We accept no claim against pre-delivery damages once the products has been delivered and signed as received in good order and condition. 2) Plug table in to mains powered 240V plug and switch on (if battery power pack, charge battery as per instructions for 24 hours as per guidelines). 3) Rechargeable Battery Systems 24 hour full uninterrupted charge is initially required before operating table. (See charging instructions in the manual.) Medifab AU Medifab NZ Page 3

4 IMPORTANT! INTENDED USE It is critical that the suitability of the correct model Ergosol Wall Mount Table is installed. Dry Area product Range - Designed for primary use as a changing table and designed for limited showering / bathing activities only - Coating is a 3-process powder coat finish - Fitted with a 240 watt mains IP66 standard actuator / motor system. Wet Area Product Range - Designed for use in a shower / bath application - Coating is polished stainless steel 304 grade - As used for showering / bathing, recommended to only use with 12 volt IP65 battery pack actuator / motor system - Supplied with Linak rechargeable battery pack standard (IP65 rated). Loading Rating This bed is designed and only allowed for a 150kg safe working load. Medifab AU Medifab NZ Page 4

5 INSTALLATION INSTRUCTIONS The ordered Change & Wash Station will come completely assembled and only wall mounting installation is required. 1. An experienced and qualified builder must install any Change & Wash Station. 2. Liability Disclaimer Medifab accepts no liability for any injury sustained through faulty installation. It is the responsibility of the installer to ensure the table is securely fixed to a solid wall. Installation must be in accordance of Amtech Medical instructions for mounting a Change & Wash Station as per following drawings and specifications (applicable for New Zealand). Medifab AU Medifab NZ Page 5

6 MOUNTING TO WALL 885mm 663mm Medifab AU Medifab NZ Page 6

7 Wall To achieve the recommended height range for height adjustable models (of 550mm to 850mm); mount the table at the recommended height position. Mattress 130 mm to bottom of rail on framework NB: removal of pin which holds bottom of actuator in pace will need to be temporarily removed to allow screw / bolt mounting into wall. 240 Watt mains power only. Floor ELECTRICAL INSTALLATION If unit is purchased with a 240 volt (mains powered) actuator programme, then a 3 pin power outlet with RCD safety control is required. Length of cord with plug is 1 metre. Mount the plug as far away as possible from any water source, and in accordance with any local electrical safety standards and recommendations. Product can be hard wired as an option. ELECTRICAL TIPS Please read carefully: If the Change & Wash table is being installed in the same room as a shower, make sure the electrical fitting is at the opposite side of the table from where the shower is and should be hard-wired to the wall. E.g. if the shower is on the right of the table, the electrical fitting must be on the left. If the Change & Wash table is being installed in a room with NO SHOWER, you may place the electrical outlet on either side of the table, and a standard plug and socket will be adequate. Medifab AU Medifab NZ Page 7

8 OPERATING INSTRUCTIONS Up/Down Operation On the hand held control switch, simply push the up or down button ( or ) to raise or lower the bed. Fold Away Table Top The unit is designed for the padded top and frame to be folded away upright when not in use. To raise the top, gently lift the padded top to upright position. It will remain in this position (held by a gas strut) until lowering is required. To lower, simply pull down gently until top comes to rest at correct position. Medifab AU Medifab NZ Page 8

9 IMPORTANT POINTS Patients & Side Safety Rails If the patient is restless and is inclined to move on the table, it is highly recommended that a side safety rail is installed on the unit. This available accessory will safely ensure patient cannot roll off side of bed. Items which may damage padded top Supplied with this table is a high specification waterproof padded top. Ensure that the top is not able to be damaged by the patient or care givers sharp objects (ie, watches, belts, etc). Medifab AU Medifab NZ Page 9

10 MAINTENANCE INSTRUCTIONS Mechanical/Framework There is very little mechanical maintenance required, just occasionally lightly oil the guides and plastic inserts to keep the movement smooth and free. Either oil or silicone spray can be used. The bolts and nuts holding the table together are locked but an occasional check should be prudent. Cleaning The padded top and frame of the table should be kept clean from soap build up and other deposits, warn soapy water is adequate for this. DO NOT use harsh abrasives or strong acid or alkaline cleaners. Electrical The electrical components are sealed and have no user serviceable parts. Any problems should be reported to Amtech Medical in the first instance as unauthorised attempts to carry out repairs will break the seal and may void the warranty. It is advised that an electrician or electrical service technician holding a current practicing license carry out the electrical safety check as recommended by the Electrical Workers Registration Board and OSH every 12 months. The Linak Actuator System can be cleaned with brush and low water pressure cold water in the retracted static position only ie, not moving. Medifab AU Medifab NZ Page 10

11 ELECTRICAL SAFETY The Linak Actuator Systems are built and supplied to International Safety Electrical Ratings known as International Protection (IP). Full Linak technical information is available from Amtech Medical directly upon request. Detailed specifications from Linak are available on request. All Change & Wash Stations have Linak actuators specified to IP66, which represents dust-tight protection and protection against water washing, limited ingress permitted, in accordance with Linak s test procedures. Depending on geographical area, legal consent may be required on electrical safety switch/s for 240 volt system. Medifab AU Medifab NZ Page 11

12 RECHARGEABLE BATTERY INSTRUCTIONS Operation and Care (This option, only if fitted) The Linak battery system operates at a nominal 24VDc to reduce any risk of electrical discharge to the operator or patient. An emergency stop button is fitted to the battery system. The battery is mounted at the bottom of the main frame and is a split unit allowing the battery to be removed for recharging. The charger can be set in another room and the battery taken to it, the battery should ideally be charged every 24 hours; this will extend the battery life. It is important that the battery is not fully discharged at any time. To remove or replace the battery to the table is best done with the mattress in the folded up position. The battery is designed to simply snap into the mounting bracket and is easily released by pulling on the handle on the battery pack towards you. Use both hands to support the battery pack when removing or replacing it. The wall charger has a light to show the power is connected (turned on) and a second light to show it is charging the battery. When the battery is fully charged, the second light goes out. The control box on the bed does not have any lights to indicate battery condition. Medifab AU Medifab NZ Page 12

13 ACCESSORIES A fold-down safety rail is available if required. Other accessories include safety body straps and headrests which are made and supplied on request. Medifab AU Medifab NZ Page 13

14 WARRANTY Component Warranty All frame work provided correct specification and used in correct environment. Frame Actuators and Systems (excludes batteries) Castors Upholstery 5 years 3 years 2 years 1 year Warranty Conditions Amtech Medical guarantees quality of all parts supplied by us or our agents for the suitable usages and corresponding periods specified above. Amtech will replace free of charge any faulty part returned to us freight paid, which bears no evidence of mishandling, overloading, repairs or alteration made by the user / purchaser without our written consent. For claims under this warranty, contact in the first instance should be to the distributors from whom the equipment was purchased, or Amtech Medical if purchased direct. The warranty applies to the original purchaser only, and requires proof of purchase via production of the original invoice. We recommend you keep the invoice with this material for future reference. Please keep in a safe place. Disclaimer Amtech Medical accepts no liability or responsibility for any injury sustained through faulty installation or usage of any Ergosol product. It is the responsibility of the purchaser to ensure that correct installation procedures were carried out for initial set up, and suitability of the correct model Ergosol product for the application. Medifab AU Medifab NZ Page 14