Smaller Lighter More Powerful

Transcription

1 Sealed Weather-Proof Construction Smaller Lighter More Powerful Made in USA Uninterruptible Power Supply

2 Military Grade UPS (Uninterruptible Power Supply) SynQor s UPS is designed for the extreme environmental and demanding electrical conditions of Military/ Aerospace applications. SynQor s UPS incorporates field proven high efficiency designs and rugged packaging technologies. This UPS will accept a wide range of input voltage and frequency values while delivering a well-conditioned output to the load. Its use of lithium polymer batteries permits the lowest profile and lowest weight solution in its power class. It is designed and manufactured to comply with a wide range of military standards. s include a output and the ability to also draw power from a military standard 28V input. Sealed Shock-Proof Weather-Proof Construction Features Sealed, weather-proof, shock-proof construction Hot swappable internal battery pack (lithium polymer) >10 minute run-time at full power (1500VA) output power Full power operation: -20 C to +55 C Universal input: V; 47-65Hz Power factor correction at input Dual input ( and optional ) True on-line double conversion Cold start with no or input connections Pure sinusoidal output voltage (115V, 60Hz) Handles power factor loads and non-linear loads Up to 3 units can be combined for higher power, voltage or a 3-phase output User I/O and Configuration signal ports 1U high rack mount unit (17 x 21.6 ) Low weight: 32 lbs. (including battery) 1.25kW 1U Model Safety & Qualifications IEC Safety requirements for portable secondary sealed cells ST/SG/.10/11/Rev.5 UN Recommendations on the Transport of Dangerous Goods UL 1642 Lithium Batteries IEC General and safety requirements for UPS IEC UPS Electromagnetic compatibility (Category C4) *s input (28Vnom) for dual source 2U Extended battery pack gives >24 minutes of run-time 47Hz 800Hz input 115Vrms or 230Vrms output Specification Compliance 50Hz or 400Hz output UPS-1500 units are designed to meet: 1: Auxiliary isolated output (up to 500W) MIL-STD B - Interface Std for Shipboard Systems 2: High power output (up to ) parallelable for higher power MIL-STD-810G - Environmental Engineering Considerations Shipboard version with floating neutral wire MIL-STD-461F - Electromagnetic Interference MIL-STD-704F - Aircraft Electrical Power Characteristics MIL-STD-1275D - Vehicle Electrical Power Characteristics Designed and manufactured in the United States of America MADE IN USA

3 TECHNICAL electrical CHARTERISTICS INPUT CHARTERISTICS Operating Input Vrms* 47-65Hz* (Extended ) (47-800Hz al) Input Power Factor >0.98 at 47-65Hz >0.97 at 400Hz >0.93 at 800Hz Maximum Input Current Continuous 20A (full load, 85Vrms) Input Circuit Breaker Rating 25A (* Power Derating to 80% below 90Vrms) Operating Input (al) 22-33V Continuous Maximum Input Current 62A (full load, 22V) Transient Maximum Input Current 75A OUTPUT CHARTERISTICS Total Power Continuous (1500VA) Maximum 1 Power 510W Maximum 2 Power (Note: Available power is reduced by power delivered to the output) Waveform Pure Sinusoidal 115Vrms ± 3% 230Vrms ± 3% 60Hz ± 0.5% 50Hz ± 0.5% 400Hz ± 0.5% Peak Load Current 26A (115Vrms) 13A (230Vrms) Load Power Factor (leading or lagging) Total Harmonic Distortion 2% (1000W resistive load) [1] (optional) Regulation (Over Load & Temperature) ± 3% Common /Power combinations 12V at 25A = 300W (Other s Available) 15V at 25A = 375W 24V at 21A = 504W 28V at 18A = 504W 40V at 12.5A = 500W 50V at 10A = 500W [2] (optional) Setpoint ± 3% Load regulation -10% ( droops vs. load to allow passive sharing among modules.) Common /Power combinations (2) 24V at 45A = 1050W 28V at 45A = LITHIUM-POLYMER BATTERY CHARTERISTICS Standard 1U Battery Pack Run Time : 10 min 1000W : 13 min 625W : 21 min al 2U Extended Battery Pack Run Time : 24 min 1000W : 31 min 625W : 50 min Recharge Time (to 90% charge) Standard Total Power < 1000W 2 hrs al 2U Extended Battery Pack Total Power < 1000W 4 hrs Temperature Range for Recharge: 0 C to 45 C Internal heaters maintain battery temperature above 0 C when input power is present. Battery charging only enabled below +45 C. ENVIRONMENTAL CHARTERISTICS MIL-STD-810G MTBF 100kHrs MIL-217F Ground Benign, Ta=25 C Temperature Methods 501.5, Operating Temperature -20 C +55 C Storage Temperature -20 C +65 C Altitude Method Operating 0-15,000 ft Non-operating 0-40,000 ft Environmental Tests Shock/Drop Method 516.6, Procedures 1,4,6 Vibration Method 514.6, Procedure 1,2 Fungus Method Salt Fog Method Sand and Dust Method 510.5, Procedures 1,2 Rain Method EMI MIL-STD-461F Humidity Method Mechanical Vibrations of Method 528 Shipboard Equipment Electromagnetic Capability MIL-STD-461F CE Hz - 10 khz CE khz - 10 MHz CS Hz khz CS khz - 40 GHz CS khz MHz CS khz MHz RE Hz khz RE khz - 18 GHz RS Hz khz RS103 2 MHz - 40 GHz MECHANICAL CHARTERISTICS Standard 1U Battery Pack Chassis Size (H x W x D) 1.73"(1U) x 17" x 21.6" Case Material Aluminum Total Weight 32 lbs. (with chassis & battery) al 2U Extended Internal Battery Pack Chassis Size (H x W x D) 3.33"(2U) x 17" x 21.6" Case Material Aluminum Total Weight 50 lbs. (with chassis & battery) Connectors Input Connector MS3470L14-4P Input Connector MS3470L18-8P Connector MS3470L14-4S Connector MS3470L14-4SW 2nd Connector MS3470L18-8S User I/O Ports HD DB15 Female Configuration I/O Port HD DB15 Male SNMP Connector RJF6N Cooling s Sound Pressure Level (SPL) 54 db(a) Air Flow 0.67(m3/min) 23.7 CFM Two fans in system, above specs are for each fan separately.

4 Military Grade Uninterruptible Power Supply s Model Number Power Battery Full Power (80% Power) UPS-1500-S-1U (1 Standard Battery Pack) 1500VA >10 min. (>13 min.) 1U 32 lbs. 500W 1 2 UPS-1500-E-2U (1 Extended Battery Pack) 1500VA >24 min. (>31 min.) 2U 50 lbs. 500W 1 2 UPS-3000-S-2U (2 Standard Battery Packs) 2500W 3000VA >10 min. (>13 min.) 2U 64 lbs. 1000W (2x500W) UPS-3000-E-4U (2 Extended Battery Packs) 2500W 3000VA >24 min. (>31 min.) 4U 98 lbs. 1000W (2x500W) Height Weight Input (28V nom) Input Floating Neutral (47-65Hz or (115Vrms or (50Hz, 60Hz 230Vrms) or 400Hz)) Hz) UPS Power Battery Pack Size Height Input Neutral Wire Set Point UPS 1500 E 2U L 1 G 6 UPS 1500: 1500VA 3000: 3000VA 2500W S: Standard 1U: 1.73" L: 47-65Hz E: Extended N: No Battery 2U: 3.48" W: Hz 1: 115Vrms G: Grounded 2: 230Vrms F: Floating Input D S: Not Installed D: Input 5: 50Hz M: 2 Out 6: 60Hz 24V 4: 400Hz R: 2 Out 28V Additional s : None 12: 12V 000: Standard 24: 24V 0CE: CE Marking 28: 28V E00: Ethernet / 40: 40V SNMP 50: 50V Not all combinations make valid part numbers, please contact SynQor for availability. See the Product Summary web page for more options. Part Number Examples: UPS-1500-E-2U-L1G6D28-000, UPS-1500-S-1U-L2G5S UPS-1500-S-1U-L2G5S00-0CE (230V output with CE marking) block diagram INPUT INPUT or 2nd OUTPUT to w/ PFC and ISOLATION ISOLATED INVERTER OUTPUT ELECTRONIC SWITCH / Non-Isolated - Converter ISOLATED / CONVERTER OUTPUT (OPTIONAL) (OPTIONAL) BATTERY with CHARGER and ELECTRONIC SWITCH BULK ENERGY STORAGE CAPITOR

5 Military-Grade Power P A C K A G E UPS products are available in a variety of rack mounting and extended battery configurations. See the website for data sheets with more details. Status LED Status Indicator Panel Front Panel 1.73" Status LED 1U Front Panel On/Off Air intake 17.00" Rear Panels On/Off Switch Status Indicator Panel 1 1 Rear Panel Ethernet I/O USER Ground Port Port CONFIG Stud Input Port (1/4-20) COMM/AUX Ground Port Stud Input USER Ground 2 Ethernet I/O (1/4-20) Stud Port Port CONFIG Port (1/4-20) Input Input Circuit Breaker Circuit Breaker Input Circuit Breaker Side View Top View Hot swappable battery pack 21.60" Visit our website for more information UNIT MOUNTING HOLES x "

6 Advancing The Power Curve Founded in 1997, SynQor has become the technology, quality and service leader for high efficiency - converters for the telecom/datacom marketplace. The PowerQor, BusQor, DualQor, iqor, and NiQor product lines, combined with SynQor s unmatched lead-times, flexibility, design support and lowest total cost of ownership have become the benchmark sought by SynQor s worldwide customer base. In 2004, SynQor began its successful entry into the industrial, medical and military market segments with the InQor, uqor and MilQor product lines. These new technology leading - and - product lines have enabled customers to realize vast savings in space, weight and overall system costs while dramatically increasing power densities and end-system performance. Equally important is the service and support advantage SynQor has brought to customers in these market segments. Headquartered in Boxborough, Massachusetts, at the location of its manufacturing operations, SynQor is a privately owned U.S. ISO 9001 company. With a design center in Dallas, Texas, and sales/marketing offices throughout the World, SynQor quickly became the technology, quality and service leader for high efficiency - converters. SynQor s converters feature a patented two-stage power topology that greatly improves efficiency and optimizes the power dissipated by the converter. SynQor s rugged - converters, - converters, filters and systems are designed for a wide range of industrial and military applications including those required to withstand harsh environments: railway and transportation systems, industrial motion control, information displays, factory automation, critical military and power generation systems. The Military series of Unintrerruptible Power Supply units (UPS), Hi-Rel and Mil-COTS - converters and EMI filters brings SynQor s field proven highefficiency synchronous-rectifier technology to the Military/Aerospace industry. SynQor Headquarters 155 Swanson Road Boxborough, MA Phone: Fax: Toll Free (USA): mqnbofae@synqor.com Information furnished by SynQor is believed to be accurate and reliable. However, no responsibility is assumed by SynQor for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of SynQor Rev