Catalog 201 May 2015

Transcription

1 Catalog May 5

2 NDT: AN OVERVIEW Nondestructive testing (NDT) is a procedure used to examine and/or inspect materials and components to locate surface and subsurface defects in a way that allows such materials to be examined without changing or destroying their original design or structure. NDT plays a crucial role in everyday life. It is necessary to ensure structural integrity, safety and reliability in aircraft, motor vehicles, pipelines, seafaring vessels, bridges, trains, tunnels, power stations, refi neries and oil platforms. All are inspected using some method of nondestructive testing. Nondestructive testing is also a quality assurance production and management tool which can provide impressive results when used correctly. It requires an understanding of the various methods available, their capabilities and limitations, knowledge of the relevant standards and specifi cations for performing the tests. Materials, products and equipment that fail to achieve their design requirements or projected life due to undetected defects may require expensive repair or early replacement. Such defects may also be the cause of unsafe conditions or catastrophic failure, as well as the loss of revenue due to unplanned shutdowns. Nondestructive testing can be applied to each stage of an item s development, manufacture or construction. The item s materials and assembly can be examined using NDT and either accepted, rejected or repaired. NDT techniques can then be used to monitor the integrity of the item or structure throughout its service life. The most commonly used NDT methods are visual inspection, liquid penetrant inspection, magnetic particle inspection, Eddy current inspection, acoustic emission, ultrasonic inspection and radiography.

3 Spectronics Corporation manufactures a wide array of medium and highintensity inspection lamps and products that are used to detect and identify surface and subsurface flaws in the performance of nondestructive testing utilizing the visual inspection, liquid penetrant and magnetic particle methods. For more information see TABLE OF CONTENTS UV-A LED INSPECTION LAMPS OLX-65 Series OPTI-LUX 65 OPX-65 OPTIMAX 65 OPK-N OPTIMAX Multi-Lite TRI-65 Series TRITAN 65 QDR-65 Series QUADRAN 65 QDR-65 S-Series QUADRAN 65 EK- EagleEye UV-A STATIONARY LAMPS PM-6 Series PowerMAX 65 UV- Series SuperFlood PAGE NO UV-A/WHITE LIGHT LED MODULAR INSPECTION SYSTEM ONT-65 On-Trak 65 UV-A HID INSPECTION LAMPS ML-5 Series MAXIMA BIB-5P Series SB-P Series FC-Series 5 6 BLUE LIGHT LED INSPECTION LAMPS OPX-5 OPTIMAX 5 TRI-5B TRITAN 5 PM-6B PowerMAX 5 9 BLUE LIGHT LED MODULAR INSPECTION SYSTEM ONT-5 On-Trak 5 DIGITAL RADIOMETERS XRP- AccuMAX DM-65XA 6 7 REPLACEMENT PARTS & ACCESSORIES 8 Surface metal defect revealed using the TRITAN 65 UV-A inspection lamp and Zyglo liquid penetrant WARRANTY INFORMATION PRODUCT/CUSTOMER SUPPORT & TECHNICAL ASSISTANCE 5 5 PRODUCT INDEX 55

4 UV-A LED INSPECTION LAMPS OLX-65 Series OPTI-LUX 65 UV-A LED Inspection Flashlights Affordable, Super-Compact and Designed Specifi cally for NDT! Feature a powerful UV-A (65 nm) LED light source coupled with a rugged anodized lamp body. Lightweight and compact, they reduce user fatigue while providing an extremely uniform beam profi le that surpasses those of more expensive lamps. Available in four models to suit your specifi c NDT needs: high-intensity or standard-intensity versions, each with or without an internal black light fi lter. Choice of nominal steady-state UV-A intensity of, µw/cm or maximum of,5 µw/cm at 5 inches (8 cm) Coverage area up to.5 inch (6. cm) diameter at 5 inches (8 cm), with minimum UV-A intensity of, µw/cm Anodized aluminum lamp body minimizes corrosion and stands up to years of heavy use Instant-on operation; lamp reaches full intensity immediately! Convenient on/off switch for easy, one-handed operation,-hour LED service life Powered by one rechargeable lithium-ion battery with an extra battery included with the lamp. Each provides hours of continuous inspection between charges. Meets ASTM UV-A intensity and wavelength specifi cations for FPI and MPI Both high- and standard-intensity versions are available with internal black light fi lter. Externally mounted black light fi lter with rubber bumper can be purchased as an accessory. Certifi cate of compliance for both wavelength and output measurements supplied with every lamp

5 Model OLX-65 High intensity, with clear fi lter Nominal steadystate UV-A (65 nm) intensity at 5 inches (8 cm) ➀ Visible light measurement, µw/cm.8 foot-candles (8.6 lux) Diameter of UV-A coverage area at 5 inches (8 cm) inch (5. cm) UV-A LED INSPECTION LAMPS OLX-65B High intensity, with internal black light fi lter, µw/cm. foot-candles (. lux) inch (5. cm) OPTI-LUX 65 fl ashlight with BF-65LX external black light fi lter accessory OLX-65FL Standard intensity, with clear fi lter OLX-65BFL Standard intensity, with internal black light fi lter,5 µw/cm maximum ➁,5 µw/cm maximum ➁. foot-candles (. lux). foot-candles (. lux).5 inch (6. cm).5 inch (6. cm) Light Source: UV-A LED Lamp Style: Cordless fl ashlight Lamp Head Diameter:.5 in (. cm) Length: 5.9 in (5 cm) Weight (w/battery):.6 oz ( g) Power Requirement: One.7V ma/hr lithium-ion battery (rechargeable) Run Time: hours (continuous) Charge Time: hours (one or two batteries) Charging Cradle: Two-battery capability with AC and DC cord sets ➀ All UV-A intensity readings taken with Spectroline AccuMAX Series meter, and are factory set to the values shown ➁ To address aerospace industry concerns Replacement Parts & Accessories OPTI-LUX 65 Series fl ashlights come complete with lanyard, belt holster, two rechargeable batteries, smart charging cradle with AC and DC cord sets, UV-absorbing spectacles and a padded carrying case. BF-65LX External black light fi lter with rubber bumper 7 Dome lens 7568 Lithium-ion battery (rechargeable) 767 Internal black light fi lter 7785 Internal clear fi lter 87 Battery charging cradle with AC cord 85 DC cord set 757 Belt holster UVS- UV-absorbing spectacles CC-65 Carrying case SPECTROLINE

6 UV-A LED INSPECTION LAMPS HIGH-INTENSITY MODELS OPTI-LUX 65 Series fl ashlights are available in two high-intensity models that are designed for NDT inspection applications requiring high UV-A output. The OLX-65 is equipped with a clear fi lter, while the OLX-65B comes with an internal black light fi lter that reduces the output of wavelengths longer than nm. Both versions provide a nominal steady-state UV-A intensity of, µw/cm at 5 inches (8 cm). UV-A BEAM PROFILE SURFACE CONTOUR PROFILE AT 5 IN (8 CM) 5 TOP INTENSITY PROFILE AT 5 IN (8 CM) µw/cm 8 6 () () - (-) - () () - (-) - - () () - (-) () () (-). NORMALIZED UV IRRADIANCE Typical wavelength output profi le of OPTI-LUX 65 with and without internal black light fi lter, with peak at 65 nm. Without Black Light Filter With Black Light Filter.75 Relative Output Wavelength (nm) 6

7 STANDARD-INTENSITY MODELS OPTI-LUX 65 fl ashlights are also available in two standard-intensity models that are designed for inspection applications requiring limited UV-A output. The OLX-65FL is equipped with a clear fi lter, while the OLX-65BFL comes with an internal black light filter that reduces the output of wavelengths longer than nm. These lamps also offer a larger coverage area compared to high-intensity models. Both versions provide a nominal steady-state UV-A intensity of,5 µw/cm maximum at 5 inches (8 cm), and comply with aerospace industry standards. 6 SURFACE CONTOUR PROFILE AT 5 IN (8 CM) UV-A BEAM PROFILE 5 TOP INTENSITY PROFILE AT 5 IN (8 CM) UV-A LED INSPECTION LAMPS µw/cm () () - (-) - () () - (-) - - () () - (-) () () (-) SELECT WAVELENGTHS WITH AND WITHOUT INTERNAL BLACK LIGHT FILTER As the wavelength of the OPTI-LUX 65 moves into the visible light range, the black light fi lter signifi cantly reduces the UV-A output of the lamp by as much as 5% at nm.. Without Black Light Filter With Black Light Filter.75 Relative Output Wavelength (nm) SPECTROLINE

8 UV-A LED INSPECTION LAMPS OPX-65 OPTIMAX 65 UV-A LED Inspection Flashlight (U.S. and foreign patents pending) Powerful, rechargeable, high-intensity UV-A inspection fl ashlight featuring state-of-the-art, ultra-hi-fl ux LED technology! Nominal steady-state UV-A intensity of 8, µw/cm at 5 inches (8 cm),-hour LED service life Low visible light emission less than foot-candles ( lux) Electronic Intensity Stabilizer assures consistent performance. Beam strength will not weaken between charges! Instant-on operation. Lamp reaches full intensity immediately! Rubber lamp protector prevents damage to LED head Ergonomic, portable and rugged. Anodized aluminum lamp body minimizes corrosion and stands up to years of heavy use. Powered by a rechargeable NiMH battery. Provides 9 minutes of continuous inspection between charges. Also available: DF-65 diffusing filter (sold separately). LAMP SPECIFICATIONS Style Length Cordless fl ashlight body with UV-A LED lamp head 8. inch (. cm) OPTIMAX 65 UV-A LED Inspection Flashlight comes complete with rubber lamp protector, smart AC and DC chargers, UV-absorbing spectacles, belt holster and padded carrying case. Weight.8 oz (5 g) (with Battery) Power.6V, AH NiMH internal Requirement battery stick (rechargeable) Run Time Charge Time hours Spectacles 9 minutes (continuous) UVS- UV-absorbing, clear UV-A BEAM PROFILE µw/cm (-) - - (-) SURFACE CONTOUR PROFILE AT 5 IN (8 CM) () X-INCHES (CM) () () - (-) (-) () () () Y-INCHES (CM) 5 Y-INCHES (CM) TOP INTENSITY PROFILE AT 5 IN (8 CM) - (-) (-) () () () (-) (-) () () () X-INCHES (CM) 8

9 OPK-N OPTIMAX Multi-Lite NDT Inspection Kit (U.S. patent no. 5,95,68; foreign patents pending) A New Powerful, Versatile, Multi-LED, NDT Light Source! Features three Qwik-Connect interchangeable LED lamp heads that connect to a rugged, black-anodized fl ashlight body. It provides singlewavelength illumination in UV-A and blue light, and is ideal for both pre-screening of fl uorescent particles in ambient light conditions and full-fledged NDT inspections utilizing magnetic particles or fluorescent penetrants. A convenient white light LED provides general illumination of dark work areas. UV-A LED INSPECTION LAMPS Super-powerful LED optical output with ultra-high intensity 65 nm UV-A and 5 nm blue light performance Provides nominal steady-state intensity of 8, µw/cm (UV LED) or 7, µw/cm (blue light LED) at 5 inches (8 cm),-hour LED service life Blue light LED with patented thin-fi lm dichroic lens fi lters out long-wave visible light Electronic Intensity Stabilizer ensures consistent performance. Beam strength will not weaken between charges! Instant-on operation. Lamp reaches full intensity immediately! Lightweight, cordless, ergonomic design eliminates fatigue Powered by a rechargeable NiMH battery. Provides 9 minutes of continuous inspection between charges (smart AC and DC chargers included). OPK-N Multi-Lite Inspection Kit comes complete with three storage pouches for the LED lamp heads, smart AC and DC battery chargers, UV-absorbing spectacles, fl uorescentenhancing, yellow spectacles and a padded carrying case. UV-A BEAM PROFILE µw/cm µw/cm (-) - - (-) () 9 SURFACE CONTOUR PROFILE AT 5 IN (8 CM) x-inches (cm) (-) - - (-) () () () - (-) (-) () () () SURFACE CONTOUR PROFILE AT 5 IN (8 CM) x-inches (cm) () () y-inches (cm) - (-) (-) () () () y-inches (cm) 5 UV-A LED y-inches (cm) BLUE LIGHT BEAM PROFILE 5 Blue Light LED y-inches (cm) TOP INTENSITY PROFILE AT 5 IN (8 CM) - (-) (-) () () () (-) (-) () () () x-inches (cm) TOP INTENSITY PROFILE AT 5 IN (8 CM) - (-) (-) () () () (-) (-) () () () x-inches (cm) Style Length Cordless fl ashlight body with three interchangeable LED lamp heads 9. inch (.9 cm) Weight 5. oz ( g) (with Battery) Power.6V, AH NiMH internal Requirement battery stick (rechargeable) Run Time Charge Time hours Spectacles LAMP SPECIFICATIONS 9 minutes (continuous) UVS- UV-absorbing, clear UVS- fl uorescent-enhancing, yellow SPECTROLINE

10 UV-A LED INSPECTION LAMPS TRI-65 Series TRITAN 65 Multi-LED, Broad-Beam UV-A Inspection Lamps Feature three ultra-hi-fl ux UV-A LEDs for fl uorescent inspection, plus a convenient white light LED to scan for surface fl aws and illuminate dark work areas. Their broadbeam confi guration provides an extremely wide coverage area, while a compact head design allows access into areas inaccessible to larger UV inspection lamps. Available in three models to meet your specifi c NDT inspection requirements: highintensity, standard-intensity and standardintensity with integral black light fi lters. Choice of one high-intensity model with a nominal steady-state UV-A intensity of 9, µw/cm or two standard-intensity models, both with a maximum UV-A intensity of less than 5, µw/cm at 5 inches (8 cm) Large inch ( cm) diameter coverage area at 5 inches (8 cm), with a minimum UV-A intensity of, µw/cm Low visible light emission less than foot-candles ( lux) Grip-mounted, three-way rocker switch (white light/off/uv) for easy control of light sources Built-in fans keep LEDs cool to maintain optimum light output during extended use Rubber bumper with Borofloat glass lens protects LEDs from damage Modular construction for easy servicing in the fi eld Choice of standard 8 foot (. m) or extra-long foot (6. m) heavy-duty power cord with AC plug and rubber boot. Also available: Optional in-line power supply or industrial power supply with cord sets (sold separately). Meets ASTM UV-A intensity and wavelength specifi cations for FPI and MPI Certificate of compliance for both wavelength and output measurements supplied with every lamp UV-absorbing spectacles and soft carrying case included

11 TRITAN 65 faceplate shown with (left) and without (right) integral black light fi lters. Model TRI-65HB High intensity, with clear filter TRI-65DB Standard intensity, with clear filter Nominal steady-state UV-A (65 nm) intensity at 5 inches (8 cm) ➀ Visible light measurement 9, µw/cm < foot-candles ( lux) < 5, µw/cm maximum ➁ < foot-candles ( lux) Diameter of UV-A coverage area at 5 inches (8 cm) inch ( cm) inch ( cm) UV-A LED INSPECTION LAMPS TRI-65DBB Standard intensity, with integral black light filters < 5, µw/cm maximum ➁ < foot-candles ( lux) inch ( cm) TRITAN 65 shown with optional PS-A (above) and PS-A (below) power supplies. Light Source: UV-A LEDs, White Light LED Lamp Style: Pistol grip Lamp Head Diameter:.5 in (8.5 cm) Length: 8. in (. cm) Weight: lb (5 g) White Light LED Intensity: foot-candles (,6 lux) Power Requirements: AC Lamp (TRI-65DB, TRI-65DBB, TRI-65HB) VAC* AC/DC Lamp (TRI-65MDB, TRI-65MDBB, TRI-65MHB) VAC*/VDC Battery Pack: Type V, NiMH (rechargeable) Run Time.5 hours (continuous) Charge Time hours *Also available in V, V and V versions. ➀ All UV-A intensity readings were taken with the Spectroline AccuMAX Series meter, and are factory set to the values shown ➁ To address aerospace industry concerns Also Available: TRITAN 65 M-Series portable, battery-operated AC/DC lamp kits. Include TRITAN 65 UV lamp, rechargeable NiMH battery pack, power supply adapter with AC and DC cord sets, smart AC charger, UV-absorbing spectacles and soft carrying case. 9 Standard, 8 foot (. m) AC power cord 95 Extra-long, foot (6. m) AC power cord 96.5 foot (. m) DC power cord for M series lamps 79 Particulate fi lter assembly 7955 Standard faceplate 896 Faceplate with integral black light fi lters BP- Battery pack with V rechargeable NiMH battery BR-5A Smart AC charger CC-7A Soft carrying case FP-65 Rubber bumper with Borofl oat glass PSA-5A AC/DC power supply adapter for M series lamps PS-A Industrial power supply. Primary cord: 8 feet (. m); secondary cord: feet (6. m). PS-A In-line power supply. Primary cord: 8 feet (. m); secondary cord: 8 feet (. m). UL- UV-A lens UVS- UV-absorbing spectacles SPECTROLINE

12 UV-A LED INSPECTION LAMPS HIGH-INTENSITY MODEL UV-A BEAM PROFILE The TRITAN 65 lamp is available in a high-intensity model specifically designed for NDT inspection applications requiring high UV-A output. The TRI-65HB comes equipped with a clear glass fi lter and is tuned to provide a nominal steady-state UV-A intensity of 9, µw/cm at 5 inches (8 cm). SURFACE CONTOUR PROFILE AT 5 IN (8 CM) TOP INTENSITY PROFILE AT 5 IN (8 CM) 5 () µw/cm 8 6 TRI-65HB () () - (-) - - () - () () - - () (-) (-) () () - (-) (-) - (-) () () () (-) (-) NORMALIZED UV IRRADIANCE Typical wavelength output profi le of TRITAN 65 Series with and without integral black light fi lters. Relative Output TRI-65HB TRI-65DB TRI-65DBB Wavelength (nm)

13 STANDARD-INTENSITY MODELS UV-A BEAM PROFILES µw/cm µw/cm SURFACE CONTOUR PROFILE AT 5 IN (8 CM) () - () () () - (-) () - - () (-) (-) (-) SURFACE CONTOUR PROFILE AT 5 IN (8 CM) () - () () () - (-) () - - () (-) (-) (-) 5 TRI-65DB 5 TRI-65DBB () () () - (-) (-) () () () - (-) (-) TOP INTENSITY PROFILE AT 5 IN (8 CM) () () () (-) (-) TOP INTENSITY PROFILE AT 5 IN (8 CM) () () () (-) (-) The TRITAN 65 lamp is also available in two standard-intensity models that are designed for inspection applications requiring limited UV-A output. The TRI-65DB is fi tted with a clear glass filter. The TRI-65DBB is equipped with a faceplate with integral black light filters that cover each of the LEDs and reduce the output of wavelengths longer than nm. This addresses aerospace industry concerns. Both versions are tuned to ensure that they provide a maximum steady-state UV-A intensity of less than 5, µw/cm at 5 inches (8 cm). UV-A LED INSPECTION LAMPS SELECT WAVELENGTHS WITH AND WITHOUT INTERNAL BLACK LIGHT FILTER..75 TRI-65HB TRI-65DB TRI-65DBB As the wavelength of the TRITAN 65 moves into the visible light range, the black light fi lters signifi cantly reduce the output of the lamp at nm. Relative Output Wavelength (nm) SPECTROLINE

14 UV-A LED INSPECTION LAMPS QDR-65 Series Versatile, Dual-Intensity, Multi-LED, Broad-Beam NDT Inspection Lamps! Feature four ultra-hi-fl ux UV-A LEDs plus a convenient white light LED to quickly switch between fl uorescent inspection and fl aw location. A unique dual-intensity feature provides both high and standard UV-A and white light output for added versatility. The lamps broad-beam confi guration produces an extremely wide coverage area, making them ideal for both in-line and hand-held applications. Models are available either with or without integral black light fi lters to meet your specifi c inspection requirements. The QUADRAN 65 can be quickly mounted for in-line inspections using various Spectroline accessories (FA- fl exible arm shown). Dual-intensity capability: High setting produces a nominal steady-state UV-A intensity as high as 8, µw/cm ; standard setting produces a nominal steadystate intensity of,5 µw/cm, both at 5 inches (8 cm) Extremely large coverage area of up to 6 inches (5 cm), with a minimum UV-A intensity of, µw/cm Low visible light emission less than foot-candles ( lux) Conveniently located rocker switches for quick and easy control of light sources Built-in fan keeps LEDs cool to maintain optimum light output during extended use Rubber bumper with Borofl oat glass lens protects LEDs from damage Rugged, modular construction allows for easy fi eld serviceability Lamp handle pin receptacle allows for easy attachment of various Spectroline mounting accessories for in-line inspection applications (accessories sold separately) Choice of standard 8 foot (. m) or extra-long foot (6. m) heavy-duty power cord with AC plug and rubber boot. Also available: Optional industrial power supply or in-line power supply with cord sets (sold separately). UV-absorbing spectacles and soft carrying case included

15 Model QDR-65A Standard Intensity QDR-65A High Intensity QDR-65BLA Standard Intensity Nominal steadystate UV-A (65 nm) intensity at 5 inches (8 cm) ➀,5 µw/cm maximum Visible light measurement < foot-candles ( lux) 8, µw/cm < foot-candles ( lux),5 µw/cm maximum < foot-candles ( lux) UV-A coverage area (at minimum, µw/cm ) 5 in ( cm) 6 in (5 cm) in ( cm) UV-A LED INSPECTION LAMPS QDR-65BLA High Intensity 7, µw/cm < foot-candles ( lux) 6 in (5 cm) QUADRAN 65 faceplate shown with (top) and without (bottom) integral black light fi lters. Light Source: Lamp Style: Lamp Head (WxH): Length: Weight: White Light LED Intensity: High setting: Low setting: Power Requirement: AC Lamp (QDR-65A, QDR-65BLA) AC/DC Lamp (QDR-65MA, QDR-65MBLA) Battery Pack: Type Run Time High intensity: Standard intensity: Charge Time UV-A LEDs, White Light LED Pistol grip 6 x 5.5 in (5 x cm) in (5 cm) lb (.6 kg) foot-candles (,9 lux) foot-candles (8 lux) VAC* power cord supplied with lamp VAC*/VDC V, NiMH (rechargeable).5 hours (continuous).5 hours (continuous) hours *Also available in V, V and V versions. ➀ All UV-A intensity readings were taken with Spectroline AccuMAX Series meter, and are factory set to the values shown Also Available: QUADRAN 65 M-Series portable, battery-operated AC/DC lamp kits. Include QUADRAN 65 UV lamp, rechargeable NiMH battery pack, power supply adapter with AC and DC cord sets, smart AC charger, UVabsorbing spectacles and soft carrying case. SPECTROLINE

16 UV-A LED INSPECTION LAMPS QDR-65A MODELS UV-A BEAM PROFILES When the QDR-65A is in high intensity mode, the lamp provides a nominal steady-state UV-A intensity of 8, µw/cm at 5 inches (8 cm). When switched to the standard intensity mode, the QDR-65A provides a nominal steady-state UV-A intensity of,5 µw/cm at 5 inches (8 cm). µw/cm 8 6 () SURFACE CONTOUR PROFILE AT 5 IN (8 CM) () () (-) () 5 QDR-65A (High Intensity) () () - - (-) TOP INTENSITY PROFILE AT 5 IN (8 CM) - - () () (-) In addition, the lamp has a high/ low switch to control the white light LED output. 6 5 SURFACE CONTOUR PROFILE AT 5 IN (8 CM) 6 () TOP INTENSITY PROFILE AT 5 IN (8 CM) µw/cm () () - - (-) - () () QDR-65A (Standard Intensity) () - - (-) - - () () (-) NORMALIZED UV IRRADIANCE Typical wavelength output profi le of QUADRAN 65 with and without internal black light fi lter, with peak at 65 nm...75 QDR-65A (High Intensity) QDR-65A (Standard Intensity) QDR-65BLA (High Intensity) QDR-65BLA (Standard Intensity) Relative Output Wavelength (nm) 6

17 µw/cm µw/cm 8 6 () 6 () SURFACE CONTOUR PROFILE AT 5 IN (8 CM) () - QDR-65BLA MODELS UV-A BEAM PROFILES - (-) - () SURFACE CONTOUR PROFILE AT 5 IN (8 CM) () - - (-) - () () () 5 QDR-65BLA (High Intensity) 5 QDR-65BLA (Standard Intensity) () () - - (-) () () - - (-) TOP INTENSITY PROFILE AT 5 IN (8 CM) - - () () (-) TOP INTENSITY PROFILE AT 5 IN (8 CM) - - () () (-) The QDR-65BLA is equipped with a faceplate with integral black light fi lters that reduce the output of wavelengths longer than nm. When in the high intensity mode, the lamp provides a nominal steady-state UV-A intensity of 7, µw/cm at 5 inches (8 cm). When switched to the standard intensity mode, the QDR-65BLA provides a nominal steady-state standard UV-A intensity of,5 µw/cm at 5 inches (8 cm). In addition, the lamp has a high/ low switch to control the white light LED output. UV-A LED INSPECTION LAMPS SELECT WAVELENGTHS WITH AND WITHOUT INTERNAL BLACK LIGHT FILTER Relative Output QDR-65A (High Intensity) QDR-65A (Standard Intensity) QDR-65BLA (High Intensity) QDR-65BLA (Standard Intensity) As the wavelength of the QUADRAN 65 moves into the visible light range, the black light fi lters signifi cantly reduce the output of the lamp at nm Wavelength (nm) SPECTROLINE

18 UV-A LED INSPECTION LAMPS QDR-65 S-Series Powerful, Multi-LED, Broad-Beam NDT Inspection Lamps! Feature four ultra-hi-flux UV-A LEDs plus a convenient white light LED to quickly switch between fluorescent inspection and flaw location. For increased flexibility, a unique dual-intensity feature provides high/low white light output control. The lamps broad-beam configuration produces an extremely wide coverage area, making them ideal for both in-line and hand-held applications. Two models are available, either with or without integral black light filters to meet your specific NDT inspection requirements. QUADRAN 65 S-Series lamps can be quickly mounted for in-line inspections using various Spectroline accessories (FA- fl exible arm shown). Choice of two models, both with a maximum standard UV-A intensity of,5 µw/cm at 5 inches (8 cm) Extremely large coverage area of up to 5 inches ( cm), with a minimum UV-A intensity of, µw/cm Low visible light emission less than foot-candles ( lux) Conveniently located rocker switches for quick and easy control of light sources Built-in fan keeps LEDs cool to maintain optimum light output during extended use Rubber bumper with Borofl oat glass lens protects LEDs from damage Rugged, modular construction allows for easy fi eld serviceability Lamp handle pin receptacle allows for easy attachment of various Spectroline mounting accessories for in-line inspection applications (accessories sold separately) Choice of standard 8 foot (. m) or extra-long foot (6. m) heavy-duty power cord with AC plug and rubber boot. Also available: Optional industrial power supply or in-line power supply with cord sets (sold separately). Meets ASTM UV-A intensity and wavelength specifi cations for FPI and MPI Certifi cate of compliance for both wavelength and output measurements supplied with every lamp UV-absorbing spectacles and soft carrying case included 8

19 Model QDR-65SA QDR-65SBLA With integral black light fi lters Nominal steadystate UV-A (65 nm) intensity at 5 inches (8 cm) ➀,5 µw/cm maximum ➁,5 µw/cm maximum ➁ Visible light measurement < foot-candles ( lux) < foot-candles ( lux) UV-A coverage area (at minimum, µw/cm ) 5 in ( cm) in ( cm) UV-A LED INSPECTION LAMPS QUADRAN 65 S-Series faceplate shown with (top) and without (bottom) integral black light fi lters. Light Source: UV-A LEDs, White Light LED Lamp Style: Pistol grip Lamp Head (WxH): 6 x 5.5 in (5 x cm) Length: in (5 cm) Weight: lb (.6 kg) White Light LED Intensity: High setting: foot-candles (,9 lux) Low setting: foot-candles (8 lux) Power Requirement: AC Lamp (QDR-65SA, QDR-65SBLA) VAC* power cord supplied with lamp AC/DC Lamp (QDR-65MSA, QDR-65MSBLA) VAC*/VDC Battery Pack: Type V, NiMH (rechargeable) Run Time.5 hours (continuous) Charge Time hours *Also available in V, V and V versions. ➀ All UV-A intensity readings were taken with Spectroline AccuMAX Series meter, and are factory set to the values shown ➁ To address aerospace industry concerns Also Available: QUADRAN 65 MS-Series portable, battery-operated AC/DC lamp kits. Include QUADRAN 65 UV lamp, rechargeable NiMH battery pack, power supply adapter with AC and DC cord sets, smart AC charger, UVabsorbing spectacles and soft carrying case. SPECTROLINE

20 UV-A LED INSPECTION LAMPS QUADRAN 65 S-Series lamps are available in two models (QDR-65SA and QDR-65SBLA). Both are designed for NDT inspection applications requiring limited UV-A output. The QDR- 65SA comes with a standard faceplate. The QDR-65SBLA is equipped with a faceplate containing integral black light fi lters that reduce the output of wavelengths longer than nm. µw/cm 6 5 () STANDARD-INTENSITY MODELS UV-A BEAM PROFILES SURFACE CONTOUR PROFILE AT 5 IN (8 CM) () - - (-) - () SURFACE CONTOUR PROFILE AT 5 IN (8 CM) () 6 QDR-65SA () () - - (-) TOP INTENSITY PROFILE AT 5 IN (8 CM) - - () () (-) TOP INTENSITY PROFILE AT 5 IN (8 CM) Both lamps are tuned to provide a nominal steady-state UV-A intensity of,5 µw/cm at 5 inches (8 cm). This addresses aerospace industry concerns. In addition, both lamps have a high/low switch to control the white light LED output. µw/cm 6 () () - - (-) - () () 5 QDR-65SBLA () () - - (-) - - () () (-) NORMALIZED UV IRRADIANCE SELECT WAVELENGTHS WITH AND WITHOUT INTERNAL BLACK LIGHT FILTER Typical wavelength output profi le of QUADRAN 65 S-Series lamps with and without black light fi lters. As the wavelength of the QUADRAN 65 S-Series moves into the visible light range, the black light fi lters signifi cantly reduce the output of the lamp at nm... QDR-65SA QDR-65SBLA QDR-65SA QDR-65SBLA Relative Output.5 Relative Output Wavelength (nm) Wavelength (nm)

21 All QUADRAN 65 Series lamps are ideal for performing both in-line and hand-held inspections! QDR-65 and QDR-65 S-Series lamps can easily be attached to a variety of Spectroline mounting accessories, as well as to our optional in-line power supplies. UV-A LED INSPECTION LAMPS QUADRAN 65 lamp shown with optional PS-A (left) and PS-A (right) power supplies. Replacement Parts & Accessories for the QDR-65 & QDR-65 S-Series 9 Standard, 8 foot (. m) AC power cord 95 Extra-long, foot (6. m) AC power cord 96.5 foot (. m) DC power cord for M series lamps 79 Particulate filter assembly 79 Standard faceplate 89 Faceplate with integral black light fi lters B-6 Bench mount BP- Battery pack with V rechargeable NiMH battery BR-5A Smart AC charger CC- Soft carrying case FA- Flexible arm FP-55 PSA-5A PS-A PS-A Rubber bumper with Borofl oat glass AC/DC power supply adapter for M series lamps Industrial power supply. Primary cord: 8 feet (. m); secondary cord: feet (6. m). In-line power supply. Primary cord: 8 feet (. m); secondary cord: 8 feet (. m). W-6 Bench mount with pin WM- UL- UVS- Wall mounting bracket UV-A lens UV-absorbing spectacles SPECTROLINE

22 UV-A LED INSPECTION LAMPS EK- UV-A/White Light LED Inspection Kit (U.S. and foreign patents pending) Palm-Sized, Cool-Running, Hands-Free Light Source! Ideal for fl uorescent magnetic particle and penetrant testing, mining inspection and a variety of other specialized applications! Spray and inspect in one simple step! Compact, lightweight lamp with two ultra-high intensity UV-A (65 nm) LEDs for inspection, plus a three-led white light assembly for general illumination Adjustable strap allows lamp to be worn on a hard hat or directly on the head for hands-free operation Unique lamp mount/sprayer attachment permits lamp and spray can to be mounted together for convenient, single-handed fl uorescent yoke inspection Built-in fan keeps lamp cool to maintain optimum UV-A intensity during extended use Splash guard with integral particulate fi lter protects UV lenses and cooling fan from damage,-hour LED service life Powered by a rechargeable lithium-ion battery (included). Provides up to 75 minutes of continuous inspection between charges. Certifi cate of compliance for both wavelength and output measurements supplied with every lamp

23 µw/cm LAMP SPECIFICATIONS Product Number: EE-65 Light Sources: UV LEDs, white light LEDs Dimensions: Length.75 in (9.5 cm) Width.5 in (5.7 cm) Height.85 in (.7 cm) Weight with Battery: 8 oz (7 g) Power Requirement: One.7V ma/hr lithium-ion battery (rechargeable) Run Time: 75 minutes (continuous) Charge Time: hours (two batteries) Charging Cradle: Two-battery capability with AC and DC cord sets. Nominal Steady-State UV-A (65 nm) Intensity: 6 in (5 cm), µw/cm² 5 in (8 cm),5 µw/cm² in (6 cm), µw/cm² 6 in (9 cm), µw/cm² UV-A LED INSPECTION LAMPS EK- EagleEye Kit comes with a lanyard, two replacement splash guards with integral particulate fi lters, two spare batteries, battery charging cradle with AC and DC cord sets, UV-absorbing spectacles and soft carrying case. NOTE: All UV-A intensity readings taken with a Spectroline AccuMAX Series meter UV-A BEAM PROFILE (-) - SURFACE CONTOUR PROFILE AT 5 IN (8 CM) - (-) () X-inches (cm) () () - (-) (-) () () () Y-inches (cm) 6 Y-inches (cm) - (-) (-) () () TOP INTENSITY PROFILE AT 5 IN (8 CM) () (-) (-) () () () X-inches (cm) Replacement Parts & Accessories EE-65 LMS- HS- SG- UV-A/white light LED lamp Lamp mount/sprayer Head strap Splash guard with integral particulate fi lter (set of three) 87 Battery charging cradle with AC cord 85 DC cord set for Lithium-ion battery (rechargeable) UVS- UV-absorbing spectacles UL- UV-A lens CC-7A Soft carrying case SPECTROLINE

24 UV-A STATIONARY LAMPS PM-6 Series UV-A LED Panel Flood Lamps Designed Specifi cally for NDT Professionals! PowerMAX 65 Series fl ood lamps feature a panel of 6 powerful UV-A (65 nm) LEDs specially engineered for non-destructive testing applications. These versatile, stationary light sources can be installed overhead or in-line, and can be ganged together to provide an even wider coverage area. Available in four models to meet your specifi c inspection needs: high-intensity and standardintensity versions, each with or without a black light fi lter. Ideal for NDT inspection booths, fl uorescent penetrant and magnetic particle inspection, screening of fl uorescent particles, wash station inspection and many other applications requiring maximum uniformity of UV-A coverage over a large area. Choice of two high-intensity models with a nominal steady-state UV-A intensity as high as 8, µw/cm or two standard-intensity models with a maximum UV-A intensity of,5 µw/cm at 5 inches (8 cm) Large coverage area of 5 inches by 6 inches (8 cm x 5 cm), with a minimum UV-A intensity of, µw/cm Low visible light emission less than foot-candles ( lux) Easily mountable for overhead inspection or in-line applications Built-in fans keep LEDs cool to maintain optimum light output during extended use Customizable multiple lamp units can be ganged together longitudinally or back-to-back for a larger coverage area to meet your specifi c inspection requirements! Both high- and standard-intensity versions available with or without black light fi lter Standard-intensity lamps meet ASTM UV-A intensity and wavelength specifi cations for FPI and MPI, and come with a certifi cate of compliance for both wavelength and output measurements

25 Top View Model Nominal steady-state UV-A (65 nm) intensity at 5 inches (8 cm) ➀ Visible light measurement UV-A coverage area (at minimum µw/cm ) PM-6UVH High intensity, with clear fi lter PM-6BLH High intensity, with black light fi lter PM-6UV Standard intensity, with clear fi lter 8, µw/cm < foot-candles ( lux) 6,5 µw/cm < foot-candles ( lux),5 µw/cm maximum ➁ < foot-candles ( lux) 5 in by 6 in (8 cm x 5 cm) 5 in by 6 in (8 cm x 5 cm) 5 in by 6 in (8 cm x 5 cm) UV-A STATIONARY LAMPS PM-6BL Standard intensity, with black light fi lter, µw/cm maximum ➁ < foot-candles ( lux) 5 in by 6 in (8 cm x 5 cm) For applications requiring extremely large coverage areas, the PowerMAX 65 can be quickly ganged together longitudinally (top) or back-to-back (below) using customized, easy-toinstall connecting plates and brackets. Light Source: 6 UV-A (65 nm) LEDs Lamp Style: Panel fl ood lamp Dimensions: 5.5 x.75 x 6 in ( x 5 x 5 cm) (W x L x H) Weight: 9 lb ( kg) Power Requirement: AC power (main AC power cord supplied with the unit) ➀ All UV-A intensity readings were taken with Spectroline AccuMAX Series meter, and are factory set to the values shown ➁ To address aerospace industry concerns Top View Replacement Parts & Accessories 877 AC power cord BF-65PM CF- Black light fi lter assembly Clear glass fi lter assembly 798 Particulate air fi lter 795 Retainer, LED assembly face plate CC- CP- CP- CP- UL- UVF-8 UVG-5 UVS- Connector cable for ganging lamps Top connecting plate for ganging lamps longitudinally Top connecting plate for ganging lamps back-to-back (Two required) Side connecting bracket for ganging lamps longitudinally (Two required) UV-A lens Face shield, UV-absorbing Goggles, UV-absorbing Spectacles, UV-absorbing SPECTROLINE

26 UV-A STATIONARY LAMPS HIGH-INTENSITY MODELS UV-A BEAM PROFILES PowerMAX 65 Series UV-A LED panel fl ood lamps are available in two high-intensity models that are specifi cally designed for NDT inspection applications requiring high UV-A output. The PM-6UVH is equipped with a clear glass filter and provides a nominal steady-state UV-A intensity of 8, µw/cm at 5 inches (8 cm). µw/cm 8 6 SURFACE CONTOUR PROFILE AT 5 IN (8 CM) -8-6 (-) - (-5) (-) - () - (-) - () () 6 () (5) 8 () 5 PM-6UVH - (-) - () () TOP INTENSITY PROFILE AT 5 IN (8 CM) (-) (-5) (-) () () (5) () The PM-6BLH is equipped with a black light fi lter that reduces the output of wavelengths longer than nm. It provides a nominal steady-state UV-A intensity of 6,5 µw/cm at 5 inches (8 cm). µw/cm 8 6 SURFACE CONTOUR PROFILE AT 5 IN (8 CM) -8-6 (-) - (-5) (-) - () - (-) - () () 6 () (5) 8 () 5 PM-6BLH - (-) - () () TOP INTENSITY PROFILE AT 5 IN (8 CM) (-) (-5) (-) () () (5) () NORMALIZED UV IRRADIANCE Typical wavelength output profi le of PowerMAX 65 Series with and without black light fi lter...75 PM-6UV PM-6BL PM-6UVH PM-6BLH Relative Output Wavelength (nm) 6

27 STANDARD-INTENSITY MODELS UV-A BEAM PROFILES µw/cm µw/cm 6 5 SURFACE CONTOUR PROFILE AT 5 IN (8 CM) -8 (-) -6 - (-5) - (-) () 6 () 8 (5) () () (-) () SURFACE CONTOUR PROFILE AT 5 IN (8 CM) -8-6 (-) - (-5) (-) - () - (-) - () () 6 () (5) 8 () 5 PM-6UV 5 PM-6BL - (-) - () () - (-) - () () TOP INTENSITY PROFILE AT 5 IN (8 CM) (-) (-5) (-) () () (5) () TOP INTENSITY PROFILE AT 5 IN (8 CM) (-) (-5) (-) () () (5) () PowerMAX 65 Series UV-A LED panel fl ood lamps are also available in two standardintensity models that are designed for NDT inspection applications requiring limited UV-A output. The PM-6UV is quipped with a clear glass filter and provides a nominal steady-state UV-A intensity of,5 µw/cm (maximum) at 5 inches (8 cm). The PM-6BL is equipped with a black light filter that reduces the output of wavelengths longer than nm. It provides a nominal steady-state UV-A intensity of, µw/cm (maximum) at 5 inches (8 cm). This addresses aerospace industry concerns. UV-A STATIONARY LAMPS SELECT WAVELENGTHS WITH AND WITHOUT INTERNAL BLACK LIGHT FILTER Relative Output PM-6UV PM-6BL PM-6UVH PM-6BLH As the wavelength of the PowerMAX 65 moves into the visible light range, the black light fi lter signifi cantly reduces the output of the lamp at nm Wavelength (nm) SPECTROLINE

28 UV-A STATIONARY LAMPS UV- Series SuperFlood Our Most Powerful UV-A Flood Lamps Designed Specifi cally for NDT These super-powerful and versatile lamps have been specially engineered for fl uorescent penetrant and magnetic particle inspection, parts degreasing inspections and wash station inspections. Powerful, -watt metal halide bulb, combined with tempered, heat-resistant low solarization UV fi lters provide the highest intensity over the largest area Easily mounts over automated magnetic particle systems or above penetrant inspection booths for the most accurate inspections of even the largest parts Unique twin-fi lter system eliminates hazardous UV-B and UV-C radiation escaping from lamp Compact design and built-in mounting features allow lamps to be positioned anywhere even in previously inaccessible areas The UV-A features a concentrated-beam refl ector designed to assure the highest concentrated UV-A intensity available. It has a nominal steady-state UV-A intensity of 8, µw/cm at lamp center, measured at 5 inches (8 cm). Irradiates an area as large as 6 x ( cm x 5 cm), producing a nominal steady-state UV-A irradiance of not less than, µw/cm. The UV-B features a unique broad-beam refl ector designed to provide NDT inspectors with maximum uniformity of coverage over the largest area. It has a nominal steady-state UV-A intensity of, µw/cm at lamp center, measured at 5 inches (8 cm). The lamp irradiates an area as wide as x (5 cm x cm) with unmatched uniformity, producing a nominal steady-state UV-A irradiance of not less than, µw/cm. UV-A BEAM PROFILE SURFACE CONTOUR PROFILE AT 5 IN (8 CM) TOP INTENSITY PROFILE AT 5 IN (8 CM) -5 µw/cm (-) X-INCHES (CM) () 5 () (-) () 5 () 5 Y-INCHES (CM) UV-A 5 Y-INCHES (CM) - -5 (-) () 5 () (-) () () X-INCHES (CM) SURFACE CONTOUR PROFILE AT 5 IN (8 CM) TOP INTENSITY PROFILE AT 5 IN (8 CM) µw/cm 6 Y-INCHES (CM) -5 (-) () 5 () (-) () X-INCHES (CM) (-) () 5 () 5 () 5 5 Y-INCHES (CM) UV-B (-) () () X-INCHES (CM) 8

29 A weld defect... UV-A STATIONARY LAMPS Revealed by the MAXIMA ML-5S UV-A inspection lamp using the liquid penetrant method. SPECTROLINE

30 UV-A/WHITE LIGHT LED MODULAR INSPECTION SYSTEM ONT-65 (U.S. and foreign patents pending) The ONT-65 On-Trak is an innovative, track light-style modular inspection system. It features four broad-beam lamps, each of which utilizes three powerful, ultra-high-fl ux UV-A (65 nm) LEDs for inspection plus one white light LED for general illumination. This overhead lighting system allows inspectors to customize lamp beam patterns to suit their individual needs. Two lamp head assemblies can be added, as desired, to increase the coverage area. Perfect for NDT inspection booths, pre-inspections and screening applications requiring maximum uniformity of coverage over large areas. Cool-running, energy-effi cient LEDs Broad-beam profi les provide wide coverage area Electronic Intensity Stabilizers ensure consistent LED performance Instant-on operation; lamps reach full intensity immediately Built-in fans keep LEDs cool to maintain optimum UV-A intensity during extended use Produces less than foot-candles of visible light Filter protectors with rubber bumpers and Borofl oat glass lenses prevent damage to LEDs Easily customizable! Move, adjust and add up to two lamp heads according to your specifi c inspection requirements (additional lamp heads sold separately) Optional remote control with three-position rocker switch provides added convenience and versatility Comes complete with UVS- UV-absorbing spectacles

31 LAMP SPECIFICATIONS Optional remote control with three-position rocker switch adds convenience and versatility Product Number: ONT-65 Light Sources: UV-A LEDs and white light LED per lamp head System dimensions: (L x W x H) 8.5 x 8. x in (7 x 6 x 8 cm) Lamp: Head diameter: Length:.5 in (8. cm) 9.5 in ( cm) Platform Dimensions: (L x W x H) 8.5 x 8. x.5 in (7 x 6 x 6 cm) Platform Weight: lb (5.9 kg) Power Supply Cord: 8 ft (. m) Power Supply: Input: - VAC 5/6 Hz Output: VDC Nominal Steady-State UV-A (65 nm) Intensity: 5 in (8 cm) 9, µw/cm² UV-A/WHITE LIGHT LED MODULAR INSPECTION SYSTEM NOTE: UV-A intensity reading taken with a Spectroline AccuMAX Series meter UV-A BEAM PROFILE SURFACE CONTOUR PROFILE AT 5 IN (8 CM) TOP INTENSITY PROFILE AT 5 IN (8 CM) µw/cm Y-inches (cm) (-) () 5 () (-) () X-inches (cm) (-) 5 () () () 5 5 Y-inches (cm) (-) () () X-inches (cm) Replacement Parts & Accessories LA-65 UV-A/white light LED lamp head assembly PS-A Power supply module PT- UL- FP- Platform and track assembly UV-A lens Filter protector with rubber bumper and Borofl oat glass lens RC- UVS- UVG-5 AC remote control with 8 foot (. m) cord Spectacles, UV-absorbing Goggles, UV-absorbing AF- Air fi lter (package of ) UVF-8 Face shield, UV-absorbing SPECTROLINE

32 UV-A HID INSPECTION LAMPS ML-5 Series MAXIMA Ultra-High Intensity UV-A Lamps These super-powerful lamps make NDT inspections easier, safer and more reliable. They feature state-of-the-art micro discharge light (MDL) technology with a fatigue-free ergonomic design. Powerful, 5 watt high-intensity MDL bulb Deliver up to times the UV-A output of conventional HID inspection lamps Prefocused at the factory Instant on/off/restrike Lightweight, solid-state ballast Integral bulb/refl ector assembly Stay-cool, impact-resistant and dent-proof housing Battery-operated versions available All bulbs feature a rated life of, hours Come complete with both UV-absorbing and fl uorescent-enhancing spectacles The MAXIMA series consists of three models:» The ML-5S with a spot refl ector has a nominal steady-state UV-A intensity of 5, µw/cm at 5 inches (8 cm). Works even in direct sunlight!» The ML-5D with a spot refl ector and diffusing fi lter has a nominal steady-state UV-A intensity of, µw/cm at 5 inches (8 cm).» The ML-5FL with a fl ood refl ector has a nominal steady-state UV-A intensity of,5 µw/cm at 5 inches (8 cm). Line voltage model All models come standard with 8 foot (. m) primary and secondary cords. Lamps are also available with extended length primary cords or with a 5 foot (.7 m) secondary cord housed in a retractable fl ying reel. In addition, all MAXIMA lamps are available in battery-operated M versions. Each includes a -volt, 7 amp/hr rechargeable battery that will operate the lamp for a full two hours. A battery charger and carrying case are included. ML-5 Series lamp with 5 foot (.7 m) secondary cord housed in a retractable fl ying reel Battery-operated M version

33 UV-A BEAM PROFILES SURFACE CONTOUR PROFILE AT 5 IN (8 CM) TOP INTENSITY PROFILE AT 5 IN (8 CM) µw/cm µw/cm (-) (-) () X-INCHES (CM) () () SURFACE CONTOUR PROFILE AT 5 IN (8 CM) - (-) (-) () () () Y-INCHES (CM) 6 ML-5S Y-INCHES (CM) Y-INCHES (CM) - (-) (-) () () () (-) (-) () () () - (-) (-) () () X-INCHES (CM) TOP INTENSITY PROFILE AT 5 IN (8 CM) UV-A HID INSPECTION LAMPS - (-) (-) () X-INCHES (CM) () () - (-) (-) () () () Y-INCHES (CM) ML-5D () (-) (-) () () () X-INCHES (CM) SURFACE CONTOUR PROFILE AT 5 IN (8 CM) TOP INTENSITY PROFILE AT 5 IN (8 CM) (-) - - µw/cm Y-INCHES (CM) - (-) () () - (-) (-) () X-INCHES (CM) () () - (-) (-) () () () Y-INCHES (CM) ML-5FL () (-) (-) () () () X-INCHES (CM) SPECTROLINE

34 UV-A HID INSPECTION LAMPS BIB-5P Series World s Highest Intensity, Self-Ballasted UV-A Lamp This lamp is a favorite with NDT inspectors because it provides super-high UV-A intensity at an economical price. Its light weight and ergonomic design ensure easy handling for long inspections. Unique Built-In-Ballast 5-watt bulb eliminates the need for a heavy, external transformer Space-age engineering polymer housing is impact-resistant and dent-proof Total weight of only / lbs (.5 kg). Measures just 9 5 /8 inches ( cm) long, including the heat guard/stand Vinyl-coated, stainless-steel, wraparound heat guard protects against burns and acts as a lamp stand Special Bulb-Saver minimizes bulb movement during handling and reduces the risk of breakage Come complete with UV-absorbing spectacles Meets ASTM UV-A intensity and wavelength specifi cations for FPI and MPI Available in either concentrated spot or broad-beam versions. Concentrated spot confi guration has a nominal steady-state UV-A intensity of,5 µw/cm at 5 inches (8 cm). Broad-beam confi guration has a nominal steady-state UV-A intensity of, µw/cm at 5 inches (8 cm). Both models come standard with an 8 foot (. m) power cord. Lamps are also available with extended length power cords or with a 5 foot (.7 m) cord housed in a retractable fl ying reel. UV-A BEAM PROFILES SURFACE CONTOUR PROFILE AT 5 IN (8 CM) TOP INTENSITY PROFILE AT 5 IN (8 CM) 6 - (-) µw/cm Y-INCHES (CM) - (-) () () - - (-) - - (-) () () X-INCHES (CM) () - (-) (-) () () () Y-INCHES (CM) BIB-5P () (-) (-) () () () X-INCHES (CM) SURFACE CONTOUR PROFILE AT 5 IN (8 CM) TOP INTENSITY PROFILE AT 5 IN (8 CM) 6 - (-) µw/cm 5 5 Y-INCHES (CM) (-) () () - - (-) - - (-) () () X-INCHES (CM) () - (-) (-) () () () Y-INCHES (CM) BIB-5P (BROAD-BEAM) () (-) (-) () () () X-INCHES (CM)

35 SB-P Series Designed for Maximum Efficiency and Versatility We developed the SB-P Series UV-A lamps to be very affordable, super-high intensity workhorses for MPI and FPI inspections. Powerful, transformer-based, watt spot bulb Combines state-of-the-art innovations with proven features. The cord comes out of the staycool, contoured handle to prevent tangling, and the crack-resistant, tempered filter reduces replacement costs significantly. Lamp head and transformer base housings are constructed of a special heat-resistant engineering polymer that ensures years of rugged use Lamp head is ergonomically designed and detaches easily from the transformer base for comfortable, fatigue-free handling Transformer provides maximum power to the unit and features an indicator light to show when the lamp is on Meets ASTM UV-A intensity and wavelength specifi cations for FPI and MPI Available in concentrated spot SB-P and diffused SB-PD versions. Spot configuration has a nominal steady-state UV-A intensity of,8 µw/cm at 5 inches (8 cm). Diffused configuration has a nominal steady-state UV-A intensity of, µw/cm at 5 inches (8 cm). Bulbs feature average rated life of 5, hours Come complete with UV-absorbing spectacles Both models come with a special heat-resistant, -wire secondary cord. The primary and secondary cords are both 8 feet (. m) long. Lamps are also available with extended length primary or secondary cords, or with a 5 foot (.7 m) secondary cord housed in a retractable fl ying reel. Also available: S/M-PQL upgraded, Premium Quality Lighting (PQL), -watt, medium base, HID replacement spot bulb, for SB-P Series lamps. Average rated bulb life is, hours. With upgraded bulb, lamp has a nominal steady-state UV-A intensity of 7,5 µw/cm at 5 inches (8 cm). UV-A HID INSPECTION LAMPS UV-A BEAM PROFILES µw/cm 6 5 SURFACE CONTOUR PROFILE AT 5 IN (8 CM) 5 Y-INCHES (CM) - (-) (-) () () TOP INTENSITY PROFILE AT 5 IN (8 CM) - - (-) - - (-) () X-INCHES (CM) () () () () - (-) (-) () Y-INCHES (CM) SB-P () (-) (-) () () () X-INCHES (CM) SURFACE CONTOUR PROFILE AT 5 IN (8 CM) TOP INTENSITY PROFILE AT 5 IN (8 CM) (-) - - µw/cm Y-INCHES (CM) - (-) () () - - (-) - - (-) () X-INCHES (CM) () () () () - (-) (-) () Y-INCHES (CM) SB-PD () (-) (-) () () () X-INCHES (CM) SPECTROLINE

36 UV-A HID INSPECTION LAMPS FC-Series World s Lightest Fan-Cooled, Portable UV-A Lamps NDT inspectors fi nd that FC-Series UV-A lamps make prolonged inspections seem much shorter because they provide cool operation and increased comfort. Quiet, built-in fan dramatically reduces running temperature, provides more comfort and safety for users, and ensures long bulb life. Ergonomically designed with the handle and cord at the balance point of the lamp head. As a result, the lamp can be held for long periods with little user fatigue. Special remote lamp switch in the pistol grip prevents accidental shutoff, while separate fan control switch allows for safe cool-down. Lamp head is housed in a super-strong engineering polymer that is dent-proof and impact-resistant. Weighs just 5 /8 lbs (.6 kg). Meets ASTM UV-A intensity and wavelength specifications for FPI and MPI Bulb features average rated life of 5, hours Come complete with UV-absorbing spectacles The FC-series consists of three models:» The FC- comes with a -watt bulb, available in concentrated spot (FC-) and diffused filter (FC-D) versions. Spot configuration has a nominal steady-state UV-A intensity of,8 µw/cm at 5 inches (8 cm). Diffused configuration has a nominal steady-state UV-A intensity of, µw/cm at 5 inches (8 cm). Both lamps come with 8 foot (. m) primary and secondary cords. Lamp head weighs just 5 /8 lbs (.6 kg).» The FC-5 with a Built-In-Ballast 5-watt concentrated spot bulb has a nominal steady-state UV-A intensity of,5 µw/cm at 5 inches (8 cm), has an 8 foot (. m) power cord. Lamp head weighs just / lbs (.6 kg).» The FC-M has the same specifi cations as the FC- model, but is a direct replacement lamp for use with Magnaflux magnetic particle machines. Lamps also available with extended length primary and secondary power cords. FC- Also available: S/M-PQL upgraded, Premium Quality Lighting (PQL), -watt, medium base, HID replacement spot bulb, for FC- Series lamps. Average rated bulb life is, hours. With the upgraded bulb, lamp has a nominal steady-state UV-A intensity of 7,5 µw/cm at 5 inches (8 cm). Magnaflux is a registered trademark of Magnaflux Corporation FC-5 6

37 UV-A BEAM PROFILES SURFACE CONTOUR PROFILE AT 5 IN (8 CM) TOP INTENSITY PROFILE AT 5 IN (8 CM) 6 - (-) µw/cm 5 5 Y-INCHES (CM) (-) () () - - (-) - - (-) () X-INCHES (CM) () () - (-) (-) () () () Y-INCHES (CM) FC- () (-) (-) () () () X-INCHES (CM) µw/cm 6 5 SURFACE CONTOUR PROFILE AT 5 IN (8 CM) 5 Y-INCHES (CM) - (-) (-) () () TOP INTENSITY PROFILE AT 5 IN (8 CM) UV-A HID INSPECTION LAMPS - - (-) - - (-) () X-INCHES (CM) () () - (-) (-) () () () Y-INCHES (CM) FC-D () (-) (-) () () () X-INCHES (CM) SURFACE CONTOUR PROFILE AT 5 IN (8 CM) TOP INTENSITY PROFILE AT 5 IN (8 CM) (-) - - µw/cm - - (-) - - (-) () X-INCHES (CM) () () - (-) (-) () () () Y-INCHES (CM) FC-5 Y-INCHES (CM) - (-) () () () (-) (-) () () () X-INCHES (CM) SPECTROLINE

38 BLUE LIGHT LED INSPECTION LAMPS LED Light Sources in Blue Light Wavelengths! The importance of high-intensity UV-A black lights for proper magnetic particle or penetrant NDT inspection is well established. However, a concern for UV safety has always existed. Our new blue light inspection lamps and modular systems address this concern. While still no substitute for UV-A lamps, blue light does provide the safety and convenience desired for quick pre-inspection or screening of fluorescent particles in operating conditions with ambient light, saving time and limiting the use of black lights to only when necessary. TRITAN 5 OPTIMAX 5 Cordless & Lightweight Flashlight! Powerful, Broad-Beam Lamp! PowerMAX 5 Versatile, Stationary Flood Lamp! Powerful, Customizable Track Light System! On-Trak 5 8

39 OPX-5 OPTIMAX 5 Rechargeable Blue Light LED Flashlight (U.S. patent no. 5,95,68; foreign patents pending) This versatile, cordless inspection lamp features a high-intensity, 5 nm blue light LED, a black anodized lamp body and our patented, thin-fi lm dichroic lens to fi lter out long-wave visible light. Nominal steady-state blue light intensity of 7, µw/cm at 5 inches (8 cm),-hour LED service life Patented, thin-fi lm dichroic lens improve contrast and fl uorescent response Electronic Intensity Stabilizer assures consistent performance. Beam strength will not weaken between charges! Instant-on operation. Lamp reaches full intensity immediately! Lightweight, cordless, ergonomic design eliminates fatigue Portable and rugged. Anodized aluminum lamp body minimizes corrosion and stands up to years of heavy use. Powered by a rechargeable NiMH battery. Provides 9 minutes of continuous inspection between charges. OPTIMAX 5 comes complete with smart AC and DC chargers, fl uorescent-enhancing, yellow spectacles, belt holster and rugged, padded carrying case. LAMP SPECIFICATIONS Style Cordless fl ashlight Lamp Head. inch (5. cm) Diameter Length 8. inch (. cm) Weight.8 oz (5 g) (with Battery) Power.6V, AH NiMH internal Requirement battery stick (rechargeable) Run Time 9 minutes (continuous) Charge Time hours BLUE LIGHT LED INSPECTION LAMPS BLUE LIGHT BEAM PROFILE SURFACE CONTOUR PROFILE AT 5 IN (8 CM) TOP INTENSITY PROFILE AT 5 IN (8 CM) (-) - µw/cm Y-INCHES (CM) - - (-) () () - - (-) - - (-) () X-INCHES (CM) () () - (-) (-) () () () Y-INCHES (CM) () (-) (-) () () () X-INCHES (CM) SPECTROLINE

40 BLUE LIGHT LED INSPECTION LAMPS TRI-5B Series TRITAN 5 Multi-LED, Broad-Beam Blue Light Lamp (U.S. patent no. 5,95,68; foreign patents pending) Feature three cool-running, ultra-high fl ux 5 nm blue light LEDs with a broad-beam confi guration. This powerful lamp provides a wider coverage area than conventional inspection lamps, while its compact head design allows access into areas inaccessible to larger inspection lamps. Ideal for most non-destructive testing applications. Nominal steady-state blue light intensity of 9,5 µw/cm at 5 inches (8 cm) Large 5 inch ( cm) diameter coverage area at 5 inches (8 cm) with a minimum intensity of, µw/cm Rubber bumper with patented thin-fi lm dichroic lens fi lters out long-wave visible light Electronic Intensity Stabilizer ensures consistent LED performance Built-in fans keep LEDs cool to maintain optimum light output during extended use Instant-on operation. Lamp reaches full intensity immediately! Rugged, ergonomic, angled lamp body provides safe, fatigue-free handling Choice of standard 8 foot (. m) or extra-long foot (6. m) heavy-duty power cord with AC plug and rubber boot. Also available: Optional in-line power supply or industrial power supply with cord sets (sold separately). Includes fl uorescent-enhancing, yellow spectacles and soft carrying case

41 µw/cm LAMP SPECIFICATIONS Style Pistol grip Light Source blue light LEDs Lamp Head Diameter 5 in ( cm) Length 8. in (. cm) Weight lb (5 g) Power Requirements: AC lamp AC/DC lamp Battery Pack: Type Run Time Charge Time (TRI-5A) VAC* (TRI-5MA) VAC*/VDC V, NiMH (rechargeable).5 hours (continuous) hours *Also available in V, V and V versions. Replacement Parts & Accessories Also Available: TRITAN 5MB portable, battery-operated AC/DC lamp kit. Includes TRITAN 5 blue light LED lamp, rechargeable NiMH battery pack, power supply adapter with AC and DC cord sets, smart AC charger, fl uorescentenhancing, yellow spectacles and soft, lightweight carrying case. 9 Standard, 8 foot (. m) AC power cord 95 Extra-long, foot (6. m) AC power cord 96.5 foot (. m) DC power cord for M series lamps 79 Particulate filter assembly BP- BR-5A CC-7A FP-5 PSA-5A PS-A PS-A UVS- Battery pack with V rechargeable NiMH battery Smart AC charger Soft carrying case Rubber bumper with dichroic lens AC/DC power supply adapter for M series lamps Industrial power supply. Primary cord: 8 feet (. m); secondary cord: feet (6. m). In-line power supply. Primary cord: 8 feet (. m); secondary cord: 8 feet (. m). Fluorescent-enhancing spectacles, yellow BLUE LIGHT LED INSPECTION LAMPS BLUE LIGHT BEAM PROFILE (-) SURFACE CONTOUR PROFILE AT 5 IN (8 CM) - - (-) () x-inches (cm) () () - (-) (-) () () () y-inches (cm) 5 y-inches (cm) TOP INTENSITY PROFILE AT 5 IN (8 CM) - (-) (-) () () () (-) (-) () () () x-inches (cm) SPECTROLINE

42 BLUE LIGHT LED INSPECTION LAMPS PM-6B Blue Light LED Panel Flood Lamp Designed Specifi cally for NDT Professionals! PowerMAX 5 fl ood lamp features a panel of 6 powerful blue light (5 nm) LEDs specially engineered for non-destructive testing applications when limiting the use of UV-A light is a requirement. This versatile, stationary light source can be installed overhead or in-line, and can be ganged together to provide an even wider coverage area. Ideal for NDT inspection booths, quick preinspection or screening of fl uorescent particles in ambient light conditions and any other applications requiring maximum uniformity of blue light coverage over a large area. Nominal steady-state blue light intensity of, µw/cm at 5 inches (8 cm) Large coverage area of 8 inches by 8 inches (6 cm x cm) with a minimum blue light intensity of, µw/cm Patented, thin-fi lm dichroic lens to fi lter out long-wave visible light Easily mountable for overhead inspection or in-line applications Built-in fans keep LEDs cool to maintain optimum light output during extended use Customizable multiple lamp units can be ganged together longitudinally or back-to-back for a larger coverage area to meet your specifi c inspection requirements!

43 µw/cm Top View LAMP SPECIFICATIONS Style Light Source Dimensions (WxLxH) Weight Power Requirement Panel fl ood lamp 6 blue light (5 nm) LEDs 5.5 x.75 x 6 in ( x 5 x 5 cm) 9 lb ( kg) AC power (main AC power cord supplied with the unit) For applications requiring extremely large coverage areas, the PowerMAX 5 can be quickly ganged together longitudinally (top) or back-to-back (bottom) using customized, easy-to-install connecting plates and brackets. Replacement Parts & Accessories Top View 877 AC power cord 798 Particulate air fi lter 795 Retainer, LED assembly face plate DF-5PM CC- CP- CP- CP- Dichroic fi lter assembly Connector cable for ganging lamps Top connecting plate for ganging lamps longitudinally Top connecting plate for ganging lamps back-to-back (two required) Side connecting bracket for ganging lamps longitudinally (two required) BLUE LIGHT LED INSPECTION LAMPS UVS- Fluorescent-enhancing spectacles, yellow BLUE LIGHT BEAM PROFILE (-) -6 - (-5) - (-) () SURFACE CONTOUR PROFILE AT 5 IN (8 CM) X-inches (cm) 6 () (5) 8 () -8 (-) -6 (-5) - (-) - () () 6 (5) 8 () Y-inches (cm) 5 Y-inches (cm) TOP INTENSITY PROFILE AT 5 IN (8 CM) -8 (-) -6 (-5) - (-) - () () 6 (5) 8 () (-) (-5) (-) () () (5) () X-inches (cm) SPECTROLINE

44 BLUE LIGHT LED MODULAR INSPECTION SYSTEM ONT-5 Blue Light LED Inspection System (U.S. and foreign patents pending) The ONT-5 On-Trak is an innovative, modular, track light-style inspection system. It features four broad-beam lamps, each of which utilizes three powerful, blue light (5 nm) LEDs. This overhead lighting system provides a fast, safe and effective alternative to UV-A light. It allows inspectors to customize lamp beam patterns to suit their individual needs, and provides the ability to add two additional lamp head assemblies to further increase the coverage area. Perfect for NDT inspection booths, pre-inspections and screening of fluorescent particles in operating conditions with ambient light or any application requiring maximum uniformity of coverage over large areas. Powerful, cool running, energy-efficient blue light LEDs Broad-beam profiles provide wide coverage area Electronic Intensity Stabilizers ensure consistent LED performance Instant-on operation; lamps reach full intensity immediately Built-in fans keep LEDs cool to maintain optimum light output during extended use Rubber bumpers with patented thin-film dichroic lenses filter out long-wave visible light while preventing damage to the LEDs Easily customizable! Move, adjust and add up to two additional lamp heads according to your specific inspection requirements (additional lamp heads sold separately) Optional remote control with two-position rocker switch provides added convenience and versatility Comes complete with UVS- fluorescence-enhancing spectacles

45 LAMP SPECIFICATIONS Product Number: ONT-5 Light Sources: blue light LEDs per lamp head System dimensions: (L x W x H) 8.5 x 8. x in (7 x 6 x 8 cm) Lamp: Head diameter: Length:.5 in (8. cm) 9.5 in ( cm) Platform Dimensions: (L x W x H) 8.5 x 8. x.5 in (7 x 6 x 6 cm) Platform Weight: lb (5.9 kg) Power Supply Cord: 8 ft (. m) Optional remote control with two-position rocker switch adds convenience and versatility Power Supply: Input: - VAC 5/6 Hz Output: VDC Nominal Steady-State Blue Light (5 nm) Intensity: 5 in (8 cm) 9,5 µw/cm² NOTE: Blue light intensity reading taken with a Spectroline AccuMAX Series meter BLUE LIGHT BEAM PROFILE µw/cm 8 6 SURFACE CONTOUR PROFILE AT 5 IN (8 CM) 5 Y-inches (cm) (-) () 5 () TOP INTENSITY PROFILE AT 5 IN (8 CM) BLUE LIGHT LED MODULAR INSPECTION SYSTEM (-) () X-inches (cm) (-) 5 () () () 5 5 Y-inches (cm) (-) () () X-inches (cm) Replacement Parts & Accessories LA-5 PS-A PT- RC- Lamp head assembly with three blue light LEDs Power supply module Platform and track assembly AC remote control with 8 foot (. m) cord FP- UVS- Filter protector with rubber bumper and thin-fi lm dichroic lens Fluorescence-enhancing spectacles, yellow AF- Air fi lter (package of ) SPECTROLINE

46 DIGITAL RADIOMETERS XRP- AccuMAX Digital Radiometer/Photometer Features an advanced microprocessor-controlled readout unit with a dual-wavelength sensor detector to measure both ultraviolet and visible light. Large, easy-to-read LCD screen Provides readouts for UV-A, visible irradiance or radiance Overall accuracy greater than ± 5% per NIST standards Choice of direct or USB cable connection between sensor detector and readout unit Superior bandpass interference filter Automatic zeroing, integration and signal hold Excellent cosine response User-selectable, multilingual display settings. Choose from English, French, German and Spanish. User-defined power save and automatic shutoff Rugged meter housing features removable, protective rubber boot for better grip and to help prevent accidental breakage Sealed sensor housing and USB connection with waterresistant adapter Compact, lightweight and battery-operated for convenient use in the factory, field or anywhere measurements are needed Complies with ASTM specifications for MPI and FPI Comes complete with readout unit, dual-wavelength sensor detector, USB cable with water-resistant adapter, protective rubber boot, two 9V alkaline batteries and padded carrying case. Relative Spectral Response XR- readout unit with dualwavelength sensor detector connected directly to unit nm 5nm nm 5nm 5nm 55nm 6nm 65nm 7nm 75nm Wavelength (nm) XR- readout unit with dual-wavelength sensor detector connected to unit via USB cable SPECIFICATIONS Readout Unit (XR-) Resolution -digit autoranging display Screen 8 x 6 dot pixel chip on glass STN transmissive monochrome LCD.8 in (7. cm) diagonal illuminated (backlit) Sample Rate 7.5 Hz (single sensor) 5 Hz (dual sensor) Read Update Hz Overall Accuracy Better than + 5% with reference to NIST standards Temperature Coefficient +.5%/ C ( to 5 C) Power Requirements Two 9V alkaline batteries (included) Dimensions Length 7.75 in (9.7 cm) Width.5 in (.8 cm) Thickness.5 in (. cm) Weight.8 lb (6 g) Dual UV-A/Visible Sensor Detector (XDS-) Irradiance Range UV-A Sensor - mw/cm (-, µw/cm ) Visible Sensor -5, lux (-5 fc) Spectral Range UV-A Sensor Visible Sensor - nm nm Dimensions Length.75 in (. cm) Width. in (5. cm) Thickness 7/8 in (. cm) Weight. lb ( g) USB Cable (Length) 5 ft (.5 m) 6

47 DM-65XA Digital UV-A Radiometer Provides increased accuracy for more repeatable results. Measures UV-A light sources with overall accuracy of ± 5% per NIST standards Autozeroing, excellent linearity and cosine response, solid-state design, compact, durable, simple operation, battery-level indicator Sealed silicone photodiode protects against shock and humidity Sensor housing is constructed with series of baffl es and unique self-sealing mechanism to eliminate light leakage Compact, lightweight and battery operated so measurements can be taken anywhere Complies with ASTM specifi cations for MPI and FPI SPECIFICATIONS Readout Unit Resolution µw/cm Screen ½ digit, 7 segment, LED display.5 in (. cm) high Overall Accuracy Better than ± 5% with reference to NIST standards Temperature Coefficient ±.5%/ C ( to 5 C) Irradiance Range -9,9 µw/cm Spectral Range - nm Power Requirements Two AA alkaline batteries (included) Length 7¼ in (8. cm) Width.5 in (8.9 cm) Thickness in (5. cm) Weight lb (.5 kg) DIGITAL RADIOMETERS Sensor Detector Length Width Thickness Weight Cord Length in (7.6 cm) in (5. cm).7 in (.8 cm) ¼ lb (.57 kg) ft (9. cm) SPECTROLINE

48 REPLACEMENT PARTS & ACCESSORIES BP-A BATTERY PACK Complete with RB-S Smart Charger with Cordset, Volt Rechargeable NiMH Battery and Nylon Carrying Case for MAXIMA TM ML-5 Series Lamps BP- BATTERY PACK Complete with BR-5A Smart Charger, Volt Rechargeable NiMH Battery for QUADRAN QDR-65M, TRITAN TRI-65M and TRI-5MB AC/DC Lamp Kits CC-A CARRYING CASE for BIB-5P Series. FC-Series and SB-P Series Lamps CC-5 CARRYING CASE for MAXIMA ML-5 Series Lamps CC-65 CARRYING CASE for OPTIMAX OPX-65 and OPX-5 Flashlights CC-7A CARRYING CASE for EagleEye and TRITAN Series Lamp Kits CC- CARRYING CASE for QUADRAN 65 Series Lamp Kits UVS- SPECTACLES UV-Absorbing UVS- SPECTACLES Fluorescence-Enhancing UVF-8 FACE SHIELD UV-Absorbing UVG-5 GOGGLES UV-Absorbing Using genuine Spectroline replacement parts ensures that lamps will operate at their optimum performance. 8

49 S SPOT BULB Ad-Medium Base, Watt for SB-P and FC-Series Lamps BLE-5RAF MDL BULB/ANODIZED REFLECTOR ASSEMBLY for MAXIMA ML-5 Series Lamps for CH-5P/ and MAXIMA ML-5 Series Lamps BLE-5FC-5/M CONCENTRATED SPOT BULB Self-Ballasted, 5 Watt for FC-5 Lamp (5 volt version) S/M SPOT BULB Medium Base, Watt for SB-P and FC-Series Lamps BLE-5BS-5/M BROAD-BEAM BULB Self-Ballasted, 5 Watt for BIB-5P Series Lamps (5 volt version) BLE-5FC-/M CONCENTRATED SPOT BULB Self-Ballasted, 5 Watt for FC-5 Lamp, ( volt version) S/M-PQL UPGRADED, PREMIUM QUALITY LIGHTING SPOT BULB Medium Base, Watt for SB-P and FC- Series Lamps BLE-5CS-/M CONCENTRATED SPOT BULB Self-Ballasted, 5 Watt for BIB-5P Series Lamps ( volt version) BLE- METAL HALIDE BULB Watt for SuperFlood UV- Series Lamps BLE-5PRA MDL BULB/POLISHED REFLECTOR ASSEMBLY for MAXIMA ML-5 Series Lamps BLE-5RA MDL BULB/COATED REFLECTOR ASSEMBLY for MAXIMA ML-5 Series Lamps BLE-5CS-5/M CONCENTRATED SPOT BULB Self-Ballasted, 5 Watt for BIB-5P Series Lamps (5 volt version) BLE-5CS-/M CONCENTRATED SPOT BULB Self-Ballasted, 5 Watt for BIB-5P Series Lamps ( volt version) 958 MDL BULB 5 Watt for MAXIMA ML-5 Series Lamps COATED SPOT REFLECTOR for MAXIMA ML-5 Series Lamps REPLACEMENT PARTS & ACCESSORIES SPECTROLINE

50 REPLACEMENT PARTS & ACCESSORIES 5 ANODIZED FLOOD REFLECTOR for MAXIMA ML-5 Series Lamps UL- UV-A LENS for LED Lamps 7796 RUBBER LAMP PROTECTOR for OPTI-LUX 65 Flashlight 78 POLISHED REFLECTOR for MAXIMA ML-5 Series Lamps F UV-A FILTER for SuperFlood UV- Series Lamps BF-65LX EXTERNAL BLACK LIGHT FILTER WITH RUBBER BUMPER for OPTI-LUX 65 Flashlight 7 DOME LENS for OPTI-LUX 65 Series LED Flashlights F5 DIFFUSING FILTER for FC-Series and MAXIMA ML-5 Series Lamps DF-65 DIFFUSING FILTER for OPTIMAX OPX-65 Flashlight OF-W LED LAMP HEAD, WHITE LIGHT for OPTIMAX OPK-N Multi-Lite Lamp FB UV-B BLOCKING FILTER for SuperFlood UV- Series Lamps OF-65UV LED LAMP HEAD, UV (65 NM) for OPTIMAX OPK-N Multi-Lite Lamp F958 UV-A FILTER for BIB-5P Series, FC-Series and MAXIMA ML-5 Series Lamps FP- FILTER PROTECTOR with Rubber Bumper/Borofloat glass lens for ONT-65 On-Trak Inspection System Lamps OF-5BD LED LAMP HEAD, BLUE LIGHT (5 NM) with dichroic lens for OPTIMAX OPK-N Multi-Lite Lamp 5565 RUBBER LAMP PROTECTOR for OPTIMAX Flashlights FP-75 FILTER PROTECTOR/LAMP STAND for BIB-5PR and FC-Series Lamps Using genuine Spectroline replacement parts ensures that lamps will operate at their optimum performance. 5

51 FP- FILTER PROTECTOR with Rubber Bumper/Dichoric glass lens for ONT-5 On-Trak blue light Inspection System Lamps HS- HEAD STRAP for EagleEye Lamp FP-65 FILTER PROTECTOR with Rubber Bumper/Borofloat Glass for TRITAN 65 Series Lamps LMS- LAMP MOUNT/SPRAYER for EagleEye Lamp FP-5 FILTER PROTECTOR with Rubber Bumper/Dichroic Filter for TRITAN 5 Series Lamps SG- SPLASH GUARDS WITH INTEGRAL PARTICULATE FILTER for EagleEye Lamp ( pack) HGS-A HEAT GUARD/STAND for SB-P Series Lamps HGS-5A HEAT GUARD/STAND for BIB-5P and BIB-5PX Lamps 7 HOLSTER for OPTIMAX OPX-65 and OPX-5 Flashlights 757 BELT HOLSTER For OPTI-LUX 65 Series Flashlights REPLACEMENT PARTS & ACCESSORIES SPECTROLINE

52 REPLACEMENT PARTS & ACCESSORIES 86 CORD SET Foot (.6 m), 7 Pin for MAXIMA ML-5 Series Lamps (V DC version) 75 DC CORD SET.5 Foot (. m) for QUADRAN and TRITAN M Series Lamps PS-A INDUSTRIAL POWER SUPPLY with cord sets for QUADRAN 65 and TRITAN Series Lamps 87 CORD SET 8 Foot (. m), 7 Pin for MAXIMA ML-5 Series Lamps (V version) 88 CORD SET 8 Foot (. m), 7 Pin for MAXIMA ML-5 Series Lamps (5V and V versions) 87 BATTERY CHARGING CRADLE with AC cord for Eagle-Eye Inspection Lamp and OPTI-LUX 65 Series Flashlights PS-A IN-LINE POWER SUPPLY for QUADRAN 65 and TRITAN Series Lamps PSA-5A POWER SUPPLY ADAPTER with AC and V DC connections for QUADRAN and TRITAN M Series Lamps 9 AC CORD SET 8 Foot (. m) for QUADRAN and TRITAN Series Lamps 85 DC CORD SET for Eagle-Eye Inspection Lamp and OPTI-LUX 65 Series Flashlights RB-S SMART BATTERY CHARGER for BP-A Battery Pack 95 AC CORD SET Foot (6. m) for QUADRAN and TRITAN Series Lamps BR-5A SMART BATTERY CHARGER for BP- Battery Pack RB- SMART AC CHARGER for OPTIMAX OPK-N, OPX-65 and OPX-5 Flashlights Using genuine Spectroline replacement parts ensures that lamps will operate at their optimum performance. 5

53 RB-DC V DC CHARGER XCB- WATER-RESISTANT USB CABLE WITH ADAPTER for AccuMAX Meter LH- LAMP HOLDER for OPTIMAX OPX-65 and OPX-5 Flashlights (for use with VF-A) for OPTIMAX OPK-N, OPX-65 and OPX-5 Flashlights RC- AC REMOTE CONTROL XCC- CARRYING CASE for AccuMAX XRP- Meter LH-A LAMP HOLDER for TRITAN Series Lamps (for use with VF-A, FA-, WM-, B-6 and W-6) for On-Trak ONT-65 UV-A Inspection System with 8 foot (. m) cord XRB- RUBBER BOOT for AccuMAX XR- Readout Unit VF-A SPEC-STIK VERIFICATION FIXTURE RC- AC REMOTE CONTROL for On-Trak ONT-5 Blue Light Inspection System with 8 foot (. m) cord AB- ADAPTER BRACKET for Mounting Transformer-Based Spectroline HID Lamps onto a Magnaflux Wet Horizontal Mag Machine for all Spectroline sensors, as well as HID, QUADRAN, TRITAN and OPTIMAX Series Lamps. NOTE: Lamp mounting accessories for TRITAN and OPTIMAX Series Lamps are sold separately (see LH- and LH-A) B-6 BENCH MOUNT 568 BATTERY STICK WITH TAILCAP for OPTIMAX OPK-N, OPX-65 and OPX-5 Flashlights 7568 LITHIUM-ION BATTERY Rechargeable for EagleEye Lamp and OPTI-LUX 65 LED Flashlights for all Spectroline HID, QUADRAN and TRITAN Series Lamps FA- FLEXIBLE ARM for all Spectroline HID, QUADRAN and TRITAN Series Lamps W-6 BENCH MOUNT for all Spectroline HID, QUADRAN and TRITAN Series Lamps WM- WALL MOUNTING BRACKET for all Spectroline HID, QUADRAN and TRITAN Series Lamps REPLACEMENT PARTS & ACCESSORIES SPECTROLINE

54 WARRANT Y & C US TOMER SE RVICE /SUPPORT Company Background Spectronics Corporation is the world s leading manufacturer of ultraviolet equipment and fluorescent materials. Spectronics supplies over, different products for the nondestructive testing, laboratory, biotechnology, industrial, electronics, semi-conductor, forensics, financial, automotive, HVAC/R and other markets. Spectronics modern,, square-foot manufacturing facility and office headquarters is located in Westbury, New York. Nearly personnel are involved in all phases of research and development, manufacturing, sales, marketing, customer service, and logistical and technical support. Over five decades since its inception, the goal of Spectronics is still the same to produce effective, top-quality products with the utmost dedication to customer satisfaction. Product Specifications Spectronics Corporation reserves the right to alter product specifications without notice. Spectronics is under no obligation to make similar changes in its products previously produced. Warranty All equipment is warranted against defects in manufacture. Spectronics Corporation s obligation under this warranty is limited to repairing or replacing, at the option of Spectronics Corporation, any part(s) of the product which, if properly installed, used and maintained, proves upon factory examination to have been defective in materials or workmanship within months from the date of delivery to the customer, including LEDs. This warranty does not apply to any component which () is normally consumed in operation or () has a normal life inherently shorter than the warranty stated. For example, bulbs, filters and rechargeable batteries are warranted for days; the S/M-PQL bulb is warranteed for 9 days. In addition, Spectronics Corporation does not warrant any instrument that has been subjected to misuse, negligence or accident, or has been repaired or altered by anyone other than Spectronics Corporation. This warranty is in place of all other warranties of quality. There are no other warranties either oral, written, express, implied or statutory. IMPLIED WARRANTIES OF FITNESS FOR PURPOSE AND MERCHANTABILITY ARE EXCLUDED. This warranty and your remedies thereunder are solely as stated in this form. In no event shall Spectronics Corporation be liable for special, indirect, incidental or consequential damages, nor for any damages arising out of delay in shipment or production. Product/Customer Support & Technical Assistance Product literature, instructions and a full staff of trained customer service representatives and technical service engineers are available for support. Additional product information and support are available on our website. Order Information Technical Assistance Local Sales Representatives Authorized Distributors Call Toll-Free: (Outside the U.S. and Canada: 56--8) Fax Toll-Free: (Outside the U.S. and Canada: ) Website CUSTOMER SERVICE 5 TECHNICAL ASSISTANCE

55 PRODUCT INDEX UV-A LED INSPECTION LAMPS EK OLX , 5 OLX-65B OLX-65FL OLX-65BFL OPX OPK-N QDR-65A , 5 QDR-65BLA QDR-65MA QDR-65MBLA QDR-65SA , 9 QDR-65SBLA QDR-65MSA QDR-65MSBLA TRI-65DB TRI-65DBB TRI-65HB , TRI-65MDB TRI-65MDBB TRI-65MHB UV-A STATIONARY LAMPS PM-6BL , 5 PM-6BLH PM-6UV PM-6UVH UV-A UV-B UV-A/WHITE LIGHT LED MODULAR INSPECTION SYSTEM ONT UV-A HID INSPECTION LAMPS BIB-5P (Broad-beam) BIB-5P (Concentrated Spot) FC- (Spot) FC- (Diffused) FC-M FC FC-5X ML-5D ML-5FL ML-5MD ML-5MFL ML-5S SB-P SB-PD BLUE LIGHT LED INSPECTION LAMPS OPX PM-6B TRI-5B TRI-5MB BLUE LIGHT LED MODULAR INSPECTION SYSTEM ONT DIGITAL RADIOMETERS DM-65XA XRP REPLACEMENT PARTS & ACCESSORIES AB AF , 5 B ,, 5 BF-65LX , 5 BF-65PM BLE-5PRA BLE-5RA BLE-5RAF BLE-5BS-5/M BLE-5CS-/M BLE-5CS-5/M BLE-5CS-/M BLE-5FC-5/M BLE-5FC-/M BLE BP-A BP , 5, 9,, 8 BR-5A , 5, 9,, 5 CC-A CC , CC CC , 8 CC-7A , 5,, 8 CC , 9,, 8 CF CP , CP , CP , DF , 5 DF-5PM EE FA , 8,, 5 FP , 5 FP FP , 5 FP , 5, 5 FP FP , 9, HGS-A HGS-5A HS , 5 LA LA LH LH-A LMS , 5 OF-W OF-65UV OF-5BD PS-A , 5 PS-A ,, 5 PS-A ,, 5 PSA-5A , 5, 9,, 5 PT , 5 RB-S RB RB-DC RC , 5 RC , 5 SG , 5 UL , 5, 9,,,, 5 UVF ,, 8 UVG ,, 8 UVS-...5, 9,, 5, 9,,, 5,,,, 6, 8 UVS ,, 9,,, 5, 8 VF-A W ,, 5 WM ,, 5 XCB XCC XRB S S/M S/M-PQL , , , 5, 9,, ,, , , , , ,9, , 9, , ,, 5, ,, 5, , 5, 9,, , 5, 9,, 5 F F FB F PRODUCT INDEX SPECTROLINE

56 NEED HELP? Call Toll-Free: (Outside the U.S. and Canada: 56--8) Fax Toll-Free: (Outside the U.S. and Canada: ) Website: Proud Members of: American Society for Nondestructive Testing American Society for Testing & Materials 5/5 A98-6 PRINTED IN U.S.A.