Galaxy kva 380/400/415 V UPS Technical Specifications 08/2017.

Transcription

1 Galaxy kva 380/400/415 V UPS Technical Specifications 08/2017

2 Legal Information The Schneider Electric brand and any registered trademarks of Schneider Electric Industries SAS referred to in this guide are the sole property of Schneider Electric SA and its subsidiaries. They may not be used for any purpose without the owner's permission, given in writing. This guide and its content are protected, within the meaning of the French intellectual property code (Code de la propriété intellectuelle français, referred to hereafter as "the Code"), under the laws of copyright covering texts, drawings and models, as well as by trademark law. You agree not to reproduce, other than for your own personal, noncommercial use as defined in the Code, all or part of this guide on any medium whatsoever without Schneider Electric's permission, given in writing. You also agree not to establish any hypertext links to this guide or its content. Schneider Electric does not grant any right or license for the personal and noncommercial use of the guide or its content, except for a non-exclusive license to consult it on an "as is" basis, at your own risk. All other rights are reserved. Electrical equipment should be installed, operated, serviced, and maintained only by qualified personnel. No responsibility is assumed by Schneider Electric for any consequences arising out of the use of this material. As standards, specifications, and designs change from time to time, please ask for confirmation of the information given in this publication.

3 kva 380/400/415 V UPS Table of Contents Important Safety Instructions SAVE THESE INSTRUCTIONS...5 Safety Precautions...6 Technical Data...8 Model list...8 Input Power Factor...8 Efficiency...8 Efficiency Curves...9 Derating due to Load Power Factor...10 Batteries...10 Efficiency DC to AC...10 End of Discharge Voltage Compliance Facility Planning...12 Input Specifications...12 Bypass Specifications...12 Output Specifications...12 Battery Specifications...13 End of Discharge Current...13 Recommended Cable Sizes...13 Power Cables for Single UPS...13 Power Cables for Parallel UPSs...14 Connection Terminals...16 Recommended Overcurrent Protection...16 Recommended Upstream and Downstream Protection...16 Recommended Residual Current Protection...18 Battery Breaker Box Configurations...18 Environmental...19 Heat Dissipation...20 Weights and Dimensions...21 Shipping Weights and Dimensions...21 Clearance...22 Default settings...23 Drawings...24 Galaxy 7000 Single System...25 Galaxy 7000 Single System with Transformer...26 Options...27 Hardware Options...27 Configuration Options...28 Parallel Capabilities...28 Limited Factory Warranty B-001 3

4

5 Important Safety Instructions SAVE THESE INSTRUCTIONS Important Safety Instructions SAVE THESE INSTRUCTIONS kva 380/400/415 V UPS Read these instructions carefully and look at the equipment to become familiar with it before trying to install, operate, service or maintain it. The following safety messages may appear throughout this manual or on the equipment to warn of potential hazards or to call attention to information that clarifies or simplifies a procedure. The addition of this symbol to a Danger or Warning safety message indicates that an electrical hazard exists which will result in personal injury if the instructions are not followed. This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages with this symbol to avoid possible injury or death. DANGER DANGER indicates a hazardous situation which, if not avoided, will result in death or serious injury. Failure to follow these instructions will result in death or serious injury. WARNING WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury. Failure to follow these instructions can result in death, serious injury, or equipment damage. CAUTION CAUTION indicates a hazardous situation which, if not avoided, could result in minor or moderate injury. Failure to follow these instructions can result in injury or equipment damage. NOTICE NOTICE is used to address practices not related to physical injury. The safety alert symbol shall not be used with this type of safety message. Failure to follow these instructions can result in equipment damage B-001 5

6 kva 380/400/415 V UPS Please Note Important Safety Instructions SAVE THESE INSTRUCTIONS Electrical equipment should only be installed, operated, serviced, and maintained by qualified personnel. No responsibility is assumed by Schneider Electric for any consequences arising out of the use of this material. A qualified person is one who has skills and knowledge related to the construction, installation, and operation of electrical equipment and has received safety training to recognize and avoid the hazards involved. Safety Precautions DANGER HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH The product must be installed according to the specifications and requirements as defined by Schneider Electric. It concerns in particular the external and internal protections (upstream circuit breakers, battery circuit breakers, cabling, etc.) and environmental requirements. No responsibility is assumed by Schneider Electric if these requirements are not respected. After the UPS system has been electrically wired, do not start up the system. Start-up must only be performed by Schneider Electric. Failure to follow these instructions will result in death or serious injury. DANGER HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH The UPS System must be installed according to local and national regulations. Install the UPS according to: IEC (including protection against electric shock, protection against thermal effect, and protection against overcurrent), or NEC NFPA 70 depending on which one of the standards apply in your local area. Failure to follow these instructions will result in death or serious injury. DANGER HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH Install the UPS system in a temperature controlled area free of conductive contaminants and humidity. Install the UPS system on a non-inflammable, level, and solid surface (e.g. concrete) that can support the weight of the system. Failure to follow these instructions will result in death or serious injury B-001

7 Important Safety Instructions SAVE THESE INSTRUCTIONS kva 380/400/415 V UPS DANGER HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH The UPS is not designed for and must therefore not be installed in the following unusual operating environments: Damaging fumes Explosive mixtures of dust or gases, corrosive gases, or conductive or radiant heat from other sources Moisture, abrasive dust, steam or in an excessively damp environment Fungus, insects, vermin Salt-laden air or contaminated cooling refrigerant Pollution degree higher than 2 according to IEC Exposure to abnormal vibrations, shocks, and tilting Exposure to direct sunlight, heat sources, or strong electromagnetic fields Failure to follow these instructions will result in death or serious injury. RISK OF OVERHEATING NOTICE Respect the clearance requirements around the UPS system and do not cover the product s ventilation openings when the UPS system is in operation. Failure to follow these instructions can result in equipment damage. RISK OF EQUIPMENT DAMAGE NOTICE Do not connect the UPS output to regenerative load systems including photovoltaic systems and speed drives. Failure to follow these instructions can result in equipment damage B-001 7

8 kva 380/400/415 V UPS Technical Data Technical Data Model list The Galaxy 7000 UPS is available in the following models: Galaxy kva 380/400/415 V Galaxy kva 380/400/415 V Galaxy kva 380/400/415 V Galaxy kva 380/400/415 V Input Power Factor For linear and non-linear load Load 25% 50% 75% 100% Power Factor 0.95 > 0.99 > 0.99 > 0.99 Efficiency The table below provides average system efficiencies on a double conversion single unit with a balanced linear load, PF 0.9, AC input voltage 400 V / AC output voltage 400 V. Efficiency on load PF 0.8 or for other input or output AC voltages is very close to the values given below for PF 0.9, voltage input / 400 V output. Difference is less than + / -0.2%. Minimum system efficiency is very close to average system efficiency. The difference is 0.2% maximum. All these measures are coming from the production line ATE statistics performed on over 200 units. System 25% load 50% load 75% load 100% load 250 kva kva kva kva B-001

9 Technical Data kva 380/400/415 V UPS Efficiency Curves 250 kva 400 V 300 kva 400 V 400 kva 400 V B-001 9

10 kva 380/400/415 V UPS Technical Data 500 kva 400 V Derating due to Load Power Factor Batteries Efficiency DC to AC Efficiency in Battery Mode Efficiency during discharge (output voltage 380 V or 400 V, inductive load PF 0.8 or 0.9 ) % load 250 kva 300 kva 400 kva 500 kva B-001

11 Technical Data kva 380/400/415 V UPS DC Power in kw PF 0.8 % load 250 kva 300 kva 400 kva 500 kva DC Power in kw PF 0.9 % load 250 kva 300 kva 400 kva 500 kva End of Discharge Voltage I batt(a) = battery current at the beginning of discharge. C10(Ah)= battery capacity in 10 hours Between 0.1 <alpha<0.97, equation of battery shutdown voltage level is : U batt mini(v/ cell) = (- 0.3x alpha) Example alpha = 0.5 Ubatt mini = 1.78V/ cell Compliance Directives for CE marking Low voltage directive EMC directive 2006/95/CEE 2004/108/CEE Safety standard of UPS CEI/EN edition 2008/2008 EMC standard of UPS CEI/EN edition 2005/2006 Declaration of conformity with UPS harmonised standards and directives IEC (Safety) and IEC (EMC) are available on demand B

12 kva 380/400/415 V UPS Facility Planning Facility Planning Input Specifications 250 kva 300 kva 400 kva 500 kva Voltage (V) Nominal input current (A) 1 Connections L1, L2, L3 Frequency (Hz) 45 to 66 Total Harmonic Distortion (THDI) Input power factor correction < 5% at full load > 0.99 at load > 50% Bypass Specifications 250 kva 300 kva 400 kva 500 kva Nominal input current (A) Connections wire (L1, L2, L3 + N + PE) Frequency (Hz) 45 to 66 Output Specifications 250 kva 300 kva 400 kva 500 kva Voltage (V) Nominal output current (A) Connections Output capacity Output frequency (sync to mains) (Hz) Slew rate (Hz/ Sec) Total Harmonic Distortion (THDU) Output power factor Dynamic load response Output voltage regulation wire (L1, L2, L3 + N + PE) 150% for 30 seconds (normal operation) 125% for 10 minutes (normal operation) 50/60 ± < 2% ph/ph 0.9 ± 1% ± 1% Crest factor For 400 V interphase voltages and a load with a power factor of B-001

13 Facility Planning kva 380/400/415 V UPS Battery Specifications Type Sealed lead-acid Vented lead-acid Ni-Cad Min./Max. number of cells 264 / / / 468 Floating voltage per cell (V) Min./Max. floating voltage (V) 600 / / / 655 Equalising voltage per cell (V) Not applicable Boost voltage per cell (V) Not applicable Min. voltage per cell (V) 1.65 to to Recharge current 0.1 x C x C C5 End of Discharge Current Sealed lead-acid Vented lead-acid Ni-Cad 250 kva 548/ / / kva 659/ / / kva 874/ / / kva 1090/ / /1012 NOTE: The battery current is an average current Pn with a power factor of 0.9 Recommended Cable Sizes Power Cables for Single UPS AC cable sizes are determined for the TNS system and for the following cable characteristics: copper single-core cables, type U1000 R02V maximum length 100 m with a line voltage drop <3% installation on perforated cable trays XLPE-type insulation, single-layer trefoil formation THDI between 15% and 33% 35 C, at 400 V grouped by four cables. Battery cable sizes are determined for: installation on perforated metallic grounded cable trays, copper, single-core cables, type U1000 R02V, maximum length 25 m with a line voltage drop <1%. UPS rating Minimum size (mm²) Normal AC line Bypass AC line Load Battery 250 kva 1 x x x x kva 1 x x x x kva 2 x x x x kva 2 x x x x Per battery cabinet B

14 kva 380/400/415 V UPS Facility Planning Power Cables for Parallel UPSs Normal AC Line and Battery AC cable sizes are determined for the TNS system and for the following cable characteristics: copper single-core cables, type U1000 R02V maximum length 100 m with a line voltage drop <3% installation on perforated cable trays XLPE-type insulation, single-layer trefoil formation THDI between 15% and 33% 35 C, at 400 V grouped by four cables. Battery cable sizes are determined for: installation on perforated metallic grounded cable trays, copper, single-core cables, type U1000 R02V, maximum length 25 m with a line voltage drop <1%. NOTE: Important: For > 200 kva UPS, the output cables must be at least 6 metres long (L 6 m). UPS rating Minimum size (mm²) Normal AC line Battery 250 kva 1 x x kva 1 x x kva 2 x x kva 2 x x Bypass AC Line and Load UPS rating Number of UPSs Total power rating (kva) Current on AC bypass or load (A) Minimum size for AC bypass or load (mm²) 250 kva x kva x kva x kva x 240 Frequency Converters UPS rating Number of UPSs Total power rating (kva) Current on AC bypass or load (A) Minimum size for load (mm²) 250 kva x kva x kva x kva x 240 NOTE: The power cables between the UPS units and the upstream protective devices must be of the same size and length. NOTE: The power cables between the UPS units and the load must be of the same size and length. 3. Per battery cabinet B-001

15 Facility Planning kva 380/400/415 V UPS Integrated Parallel UPS Units with External Bypass Cabinet UPS rating Number of UPSs Total power Current on AC bypass or load (A) Minimum size for load (mm²) rating (kva) kva x x x kva x x x kva x x x kva x x Consult us 5 NOTE: The power cables between the UPS units and the upstream protective devices must be of the same size and length. NOTE: The power cables between the UPS units and the load must be of the same size and length. Parallel UPS Units with Static-Switch Cabinet (SSC) UPS rating Number of UPS Total power rating 4 (kva) Current on AC bypass or load (A) Minimum size for load (mm²) 250 kva x x x kva x x x kva x x x kva x x Consult us 5 NOTE: The power cables between the UPS units and the upstream protective devices must be of the same size and length. NOTE: The power cables between the UPS units and the load must be of the same size and length. 4. Not including redundant UPS units. 5. Standard NFC limits the number of cables to four B

16 kva 380/400/415 V UPS Facility Planning Connection Terminals UPS Cabinets Phase terminal Earth terminal Battery terminal UPS rating Type of stud Number of holes x diameter (mm) kva 2 x M x 10 5 x 13 3 x kva N/A 4 x 13 5 x 13 3 x 13 SSC, SSC Maintenance, External Bypass Cabinets Cabinets Phase terminal Earth terminal Hole diameter (mm) 800 kva kva kva 13 and Recommended Overcurrent Protection Recommended Upstream and Downstream Protection Selection of Protection Devices Time/current Curves for UPS input and Output Fuses 6. Maximum tightening torque 25 Nm B-001

17 Facility Planning kva 380/400/415 V UPS UPS Output Current UPS 250 kva 300 kva 400 kva 500 kva In at 400 V (A) Ioutput maximum 7 (A) Ioutput minimum 7 (A) Line-current Values UPS 250 kva 300 kva 400 kva 500 kva Continuous input current (A) Input current at 1.25 In overload limited to 10 minutes (A) Input current at 1.5 In overload limited to 30 seconds (A) Input / output fuse ratings (A) For U=400V and power factor=0.9. Power Circuit Protection UPS 250 kva 300 kva 400 kva 500 kva CB Trip Unit CB Trip Unit CB Trip Unit CB Trip Unit Normal AC source NSX 630N 3P Micrologic 2.3 NSX 630N 3P Micrologic 2.3 NS 800N 3P Micrologic 2.0 NS 800N 3P Micrologic 5.0 Bypass AC source NSX 630N 4P Micrologic 2.3 NSX 630N 4P Micrologic 2.3 NS 800N 4P Micrologic 2.0 NS 800N 4P Micrologic 5.0 Output NSX 100 N TM D 80 NSX 100 N TM D 80 NSX 100 N TM D 100 C125N D 125 C120N C80 C120N C80 NG 125N C 125 NSX 160N TM 160D C120N B 125 C120N B 125 C125H C 125 NG125N D125 Icw 8 (ka) NOTE: If these downstream protection recommendations are not followed, a shortcircuit on an output circuit can result in a break in power longer than 20 ms on all the other output circuits. Permissible UPS overloads as a Function of Time Normal Mode Operation 7. RMS current limit when inverter is coupled and bypass AC source is out of tolerances 8. RMS shortime current value that can be carried without damage under condition defined by the standard IEC B

18 kva 380/400/415 V UPS Facility Planning Bypass AC Mode or Static Switch Operation Recommended Residual Current Protection Requirements for residual current protection: For single mains: The same residual current protection can be used for input and bypass. For dual mains: A transformer is required upstream of either the input or bypass. Equip each source with a circuit breaker or switch with residual current protection. The recommended minimum residual current protection is 3 A, provided the conditions defined in IEC are complied with. Battery Breaker Box Configurations HAZARD OF FIRE OR ARC FLASH WARNING Protect the battery circuit with a DC circuit breaker equipped with an undervoltage coil (MN 24 VDC). The DC breaker must be rated 660 VDC. The undervoltage coil must be wired to the UPS as shown on the diagrams. Failure to follow these instructions can result in death, serious injury, or equipment damage. The below battery solutions can be made of several strings in parallel. All strings must have the same element block and the same number of blocks (including 15% of unbalanced DC current). The below battery configurations and settings are based on nominal power at a power factor of 0.9 and 264 lead battery cells. For other battery configurations please contact Schneider Electric B-001

19 Facility Planning kva 380/400/415 V UPS Battery Configurations with One Battery Breaker (QF1) QF1 (NSX500S TM-DC) UPS Battery Backup Time Minutes Battery Strings Thermal/ Magnetic Setting (A) 250 kva < / kva < /1250 Battery Configurations with Two Battery Breakers (QF1) QF1-1 (NSX500S TM-DC) QF1-2 (NSX500S TM-DC) UPS Battery Backup Time Minutes Total Number of Battery Strings Battery Strings Thermal/ Magnetic Setting (A) Battery Strings Thermal/ Magnetic Setting (A) 250 kva Any / / / / / / / / / / kva Any / / / / / / / / / / kva Any / / / / / / kva < / / / / / /1250 Battery Configurations with Three Battery Breakers (QF1) UPS Battery Backup Time Minutes Total Number of Battery Strings QF1-1 (NSX500S TM-DC) Battery Strings Thermal/ Magnetic Setting (A) QF1-2 (NSX500S TM-DC) Battery Strings Thermal/ Magnetic Setting (A) QF1-3 (NSX500S TM-DC) Battery Strings Thermal/ Magnetic Setting (A) 400 kva Any / / / / / / kva Any / / / / / / / / /1250 Environmental Operating temperature 0-40 C Storage temperature with or without batteries Operating relative humidity C dry heat 20-95%, non-condensing B

20 kva 380/400/415 V UPS Facility Planning Storage relative humidity Operating elevation Storage elevation 20-95%, non-condensing m: 85% load m: 79% load m: 75% load m: 69% load m: 59% load meters Audible noise according to ISO 3746 (NFS ) kva 380/400/415/440 V 500 kva 380/400/415/440 V Protection class 75 dba 75 dba From IP20 to IP32 Colour Pearl dark grey (RAL 9023) Heat Dissipation 250 kva 300 kva 400 kva 500 kva Batteries fully charged Batteries charging Batteries fully charged Batteries charging Batteries fully charged Batteries charging Batteries fully charged Batteries charging Active power (kw) Efficiency Heat losses (kw) Heat losses (calories/s) B-001

21 Facility Planning kva 380/400/415 V UPS Weights and Dimensions UPS rating Weight (kg) Height (mm) Width (mm) Depth (mm) 250 kva kva kva kva Shipping Weights and Dimensions UPS Weight (kg) Height (mm) Width (mm) Depth (mm) 160 kva kva kva kva kva kva B

22 kva 380/400/415 V UPS Facility Planning Clearance NOTE: Clearance dimensions are published for airflow and service access only. Consult with the local safety codes and standards for additional requirements in your local area. NOTE: The UPS system can be placed up against the wall. It is preferable to leave some space for easier maintenance. NOTICE HAZARD OF OVERHEATING Leave nothing on top of the UPS. Maintain 500 mm of free space above the UPS. Ensure that the UPS cabinet rests on its four cylindrical feet, (six feet for 500 kva UPS). Ensure that the distance between the UPS rear panel and the floor is less than 10 mm. Failure to follow these instructions can result in equipment damage. NOTE: Leave one meter of free space in front of the UPS for door opening B-001

23 Facility Planning kva 380/400/415 V UPS Default settings System Settings (only updated when in load disconnect) Default setting Nominal output rated voltage (ph-ph) 400 V (380, 400, or 415) Frequency Frequency range Automatic start Rate of synchronization with AC Bypass source Transfer to Bypass AC AC bypass overload control 50 Hz (50 or 60 Hz) 45 Hz to 66 Hz Forbidden 1 Hz/s Allowed active AC Bypass frequency threshold tolerance 8 % AC Bypass Static Switch operation when EPO Shutdown mode (can only be set from service port) PFC current ramp enable Break duration Remote command enabled Close Never Yes 100 ms No Shutdown setting Shutdown mode (can only be set from service port) Never Other settings Battery present Battery-test interval No 1 month Low battery warning voltage threshold 20 % Low battery warning time threshold Deep battery discharge 1 minute Forbidden Display settings Display language Date format English mm/dd/yyyy Temperature unit C Main screen Password Welcome screen OOO B

24 kva 380/400/415 V UPS Drawings Drawings NOTE: A comprehensive set of drawings is available on the engineering website at engineer.apc.com. NOTE: These drawings are for reference ONLY subject to change without notice B-001

25 Drawings kva 380/400/415 V UPS Galaxy 7000 Single System B

26 kva 380/400/415 V UPS Drawings Galaxy 7000 Single System with Transformer B-001

27 Options Options kva 380/400/415 V UPS Hardware Options Battery Cabinets Galaxy 7000 Empty Battery Cabinet 700 mm Auxiliary Cabinets Galaxy 7000 Empty Auxiliary Cabinet Galaxy 7000 Empty Auxiliary Cabinet 700 mm Galaxy V Top Connection External Bypass Galaxy 7000 External Bypass Battery Circuit Breaker Boxes Galaxy 7000 Battery Circuit Breaker Box 200 kva 400 V Galaxy 7000 Auxiliaries 250 kva Galaxy 7000 Auxiliaries 300 kva Galaxy 7000 Auxiliaries 400 kva Galaxy 7000 Auxiliaries 500 kva Protection and Cover Features Galaxy 7000 Transversal Auxiliaries Galaxy V IP Cover Static Switch Cabinets Galaxy 7000 Static Bypass Switch Management Cards Network management card with ModBus/Jbus Network management teleservice card Environment sensor for network management cable B

28 kva 380/400/415 V UPS Options Configuration Options Connection through the top Isolation/Voltage matching transformer Synchronisation module B2000 or Cellwatch battery-monitoring system for block by block management Lightning arrestor (built into the UPS cabinet) Backfeed protection Jbus/Modbus + Ethernet 10/100 Multi-standard communication cards Jbus/Modbus + Ethernet 10/100 + Modem Two ports with dry contacts and/or remote shutdown Battery circuit breaker unit Supervision and shutdown software Enterprise Power Manager V.2 Parallel Capabilities Integrated Parallel UPSs UPS cabinet (1) PFC rectifier module (A) Inverter module (B) Battery chopper (C) Static-switch on AC bypass line (D) Batteries (2) Integrated Parallel UPSs with external bypass cabinet UPS cabinet (1) PFC rectifier module (A) Inverter module (B) Battery chopper (C) Static-switch on AC bypass line (D) Batteries (2) External bypass cabinet (3) B-001

29 Options kva 380/400/415 V UPS Parallel UPSs with SSC (Static-Switch Cabinet) Up to eight UPS units can be connected in parallel with a Static-Switch Cabinet. UPS 1 cabinet (1) PFC rectifier module (A) Inverter module (B) Battery chopper (C) Batteries (2) SSC (3) Static-switch on AC bypass line (D) Parallel UPSs with SSC and SSC maintenance cabinet UPS 1 cabinet (1) PFC rectifier module (A) Inverter module (B) Battery chopper (C) Batteries (2) SSC (3) Static-switch on AC bypass line (D) SSC maintenance cabinet (4) B

30 kva 380/400/415 V UPS Options Parallel UPSs set up as frequency converters UPS cabinet (1) PFC rectifier module (A) Inverter module (B) Battery chopper (C) Batteries (2) B-001

31 Limited Factory Warranty Limited Factory Warranty kva 380/400/415 V UPS One-Year Factory Warranty The limited warranty provided by Schneider Electric in this Statement of Limited Factory Warranty applies only to products you purchase for your commercial or industrial use in the ordinary course of your business. Terms of Warranty Schneider Electric warrants that the product shall be free from defects in materials and workmanship for a period of one year from the date of product start-up when start-up is performed by Schneider Electric-authorized service personnel and occurs within six months of the Schneider Electric shipment date. This warranty covers repairing or replacing any defective parts including on-site labor and travel. In the event that the product fails to meet the foregoing warranty criteria, the warranty covers repairing or replacing defective parts at the sole discretion of Schneider Electric for a period of one year from the shipment date. For Schneider Electric cooling solutions, this warranty does not cover circuit breaker resetting, loss of refrigerant, consumables, or preventive maintenance items. Repair or replacement of a defective product or part thereof does not extend the original warranty period. Any parts furnished under this warranty may be new or factoryremanufactured. Non-transferable Warranty This warranty is extended to the first person, firm, association or corporation (herein referred to by You or Your ) for whom the Schneider Electric product specified herein has been purchased. This warranty is not transferable or assignable without the prior written permission of Schneider Electric. Assignment of Warranties Schneider Electric will assign you any warranties which are made by manufacturers and suppliers of components of the Schneider Electric product and which are assignable. Any such warranties are assigned AS IS and Schneider Electric makes no representation as to the effectiveness or extent of such warranties, assumes no responsibility for any matters which may be warranted by such manufacturers or suppliers and extends no coverage under this Warranty to such components. Drawings, Descriptions Schneider Electric warrants for the warranty period and on the terms of the warranty set forth herein that the Schneider Electric product will substantially conform to the descriptions contained in the Schneider Electric Official Published Specifications or any of the drawings certified and agreed to by contract with Schneider Electric if applicable thereto ( Specifications ). It is understood that the Specifications are not warranties of performance and not warranties of fitness for a particular purpose. Exclusions Schneider Electric shall not be liable under the warranty if its testing and examination disclose that the alleged defect in the product does not exist or was B

32 kva 380/400/415 V UPS Limited Factory Warranty caused by end user or any third person misuse, negligence, improper installation or testing. Further, Schneider Electric shall not be liable under the warranty for unauthorized attempts to repair or modify wrong or inadequate electrical voltage or connection, inappropriate on-site operation conditions, corrosive atmosphere, repair, installation, start-up by non-schneider Electric designated personnel, a change in location or operating use, exposure to the elements, Acts of God, fire, theft, or installation contrary to Schneider Electric recommendations or specifications or in any event if the Schneider Electric serial number has been altered, defaced, or removed, or any other cause beyond the range of the intended use. THERE ARE NO WARRANTIES, EXPRESS OR IMPLIED, BY OPERATION OF LAW OR OTHERWISE, OF PRODUCTS SOLD, SERVICED OR FURNISHED UNDER THIS AGREEMENT OR IN CONNECTION HEREWITH. SCHNEIDER ELECTRIC DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY, SATISFACTION AND FITNESS FOR A PARTICULAR PURPOSE. SCHNEIDER ELECTRIC EXPRESS WARRANTIES WILL NOT BE ENLARGED, DIMINISHED, OR AFFECTED BY AND NO OBLIGATION OR LIABILITY WILL ARISE OUT OF, SCHNEIDER ELECTRIC RENDERING OF TECHNICAL OR OTHER ADVICE OR SERVICE IN CONNECTION WITH THE PRODUCTS. THE FOREGOING WARRANTIES AND REMEDIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES AND REMEDIES. THE WARRANTIES SET FORTH ABOVE CONSTITUTE SCHNEIDER ELECTRIC SOLE LIABILITY AND PURCHASER S EXCLUSIVE REMEDY FOR ANY BREACH OF SUCH WARRANTIES. SCHNEIDER ELECTRIC WARRANTIES RUN ONLY TO PURCHASER AND ARE NOT EXTENDED TO ANY THIRD PARTIES. IN NO EVENT SHALL SCHNEIDER ELECTRIC, ITS OFFICERS, DIRECTORS, AFFILIATES OR EMPLOYEES BE LIABLE FOR ANY FORM OF INDIRECT, SPECIAL, CONSEQUENTIAL OR PUNITIVE DAMAGES, ARISING OUT OF THE USE, SERVICE OR INSTALLATION, OF THE PRODUCTS, WHETHER SUCH DAMAGES ARISE IN CONTRACT OR TORT, IRRESPECTIVE OF FAULT, NEGLIGENCE OR STRICT LIABILITY OR WHETHER SCHNEIDER ELECTRIC HAS BEEN ADVISED IN ADVANCE OF THE POSSIBILITY OF SUCH DAMAGES, SPECIFICALLY, SCHNEIDER ELECTRIC IS NOT LIABLE FOR ANY COSTS, SUCH AS LOST PROFITS OR REVENUE, LOSS OF EQUIPMENT, LOSS OF USE OF EQUIPMENT, LOSS OF SOFTWARE, LOSS OF DATA, COSTS OF SUBSTITUANTS, CLAIMS BY THIRD PARTIES, OR OTHERWISE. NO SALESMAN, EMPLOYEE OR AGENT OF SCHNEIDER ELECTRIC IS AUTHORIZED TO ADD TO OR VARY THE TERMS OF THIS WARRANTY. WARRANTY TERMS MAY BE MODIFIED, IF AT ALL, ONLY IN WRITING SIGNED BY AN SCHNEIDER ELECTRIC OFFICER AND LEGAL DEPARTMENT. Warranty Claims Customers with warranty claims issues may access the SCHNEIDER ELECTRIC worldwide customer support network through the SCHNEIDER ELECTRIC web site: Select your country from the country selection pull-down menu. Open the Support tab at the top of the web page to obtain contact information for customer support in your region B-001

33

34 Printed in. Schneider Electric Schneider Electric 35 rue Joseph Monier Rueil Malmaison France + 33 (0) As standards, specifications, and design change from time to time, please ask for confirmation of the information given in this publication Schneider Electric. All rights reserved B-001