EPS Technical Specifications 06/2015.

Transcription

1 EPS kva Technical Specifications 06/2015

2 Legal Information The Schneider Electric brand and any registered trademarks of Schneider Electric Industries SAS referred to in this guide are the sole property of Schneider Electric SA and its subsidiaries. They may not be used for any purpose without the owner's permission, given in writing. This guide and its content are protected, within the meaning of the French intellectual property code (Code de la propriété intellectuelle français, referred to hereafter as "the Code"), under the laws of copyright covering texts, drawings and models, as well as by trademark law. You agree not to reproduce, other than for your own personal, noncommercial use as defined in the Code, all or part of this guide on any medium whatsoever without Schneider Electric's permission, given in writing. You also agree not to establish any hypertext links to this guide or its content. Schneider Electric does not grant any right or license for the personal and noncommercial use of the guide or its content, except for a non-exclusive license to consult it on an "as is" basis, at your own risk. All other rights are reserved. Electrical equipment should be installed, operated, serviced, and maintained only by qualified personnel. No responsibility is assumed by Schneider Electric for any consequences arising out of the use of this material. As standards, specifications, and designs change from time to time, please ask for confirmation of the information given in this publication.

3 kva Table of Contents Important Safety Information...5 Safety Precautions...6 Technical Data...8 Model List...8 Input Power Factor...8 Efficiency in Normal Operation...8 Efficiency Curves...9 Derating due to Load Power Factor kva/562 kw kva/720 kw kva/900 kw kva/990 kw Batteries...14 Efficiency DC to AC...14 Battery Run-Times Schneider Electric Qualified VRLA Batteries...14 Battery Material Safety Data Sheet...16 Communication and Management...17 Auxiliary Wiring...17 Compliance...18 Facility Planning...19 Input Specifications...19 Input Specifications for kva Systems...19 Input Specifications for kva Systems...19 Bypass Specifications...20 Bypass Specifications for kva Systems...20 Bypass Specifications for kva Systems...21 Output Specifications...21 Output Specifications for kva Systems...21 Output Specifications for kva Systems...22 Battery Specifications...23 Battery Specifications for kva Systems...23 Battery Specifications for kva Systems...23 Recommended Cable Sizes...24 Recommended Cable Sizes for kva Systems...24 Recommended Cable Sizes for kva Systems...25 Physical...25 Weights and Dimensions...25 Shipping Weights and Dimensions...26 Clearance...27 Environmental...28 Elevation Derating Table...28 Heat Dissipation...28 Drawings...29 EPS kva Single Module with Internal Bypass...30 EPS kva with Maintenance Bypass Cabinet...31 EPS kva Bottom Feed B-001 3

4 kva EPS kva Top Feed...33 EPS 1100 kva with Maintenance Bypass Cabinet Bottom Feed...34 EPS 1100 kva with Maintenance Bypass Cabinet Top Feed...35 Options...36 Hardware Options...36 Management...36 Configuration Options...36 Schneider Electric Limited Factory Warranty B-001

5 Important Safety Information Important Safety Information kva Read these instructions carefully and look at the equipment to become familiar with it before trying to install, operate, service or maintain it. The following safety messages may appear throughout this manual or on the equipment to warn of potential hazards or to call attention to information that clarifies or simplifies a procedure. The addition of this symbol to a Danger or Warning safety message indicates that an electrical hazard exists which will result in personal injury if the instructions are not followed. This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages with this symbol to avoid possible injury or death. DANGER DANGER indicates a hazardous situation which, if not avoided, will result in death or serious injury. Failure to follow these instructions will result in death or serious injury. WARNING WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury. Failure to follow these instructions can result in death, serious injury, or equipment damage. CAUTION CAUTION indicates a hazardous situation which, if not avoided, could result in minor or moderate injury. Failure to follow these instructions can result in injury or equipment damage. NOTICE NOTICE is used to address practices not related to physical injury. The safety alert symbol shall not be used with this type of safety message. Failure to follow these instructions can result in equipment damage. Please Note Electrical equipment should only be installed, operated, serviced, and maintained by qualified personnel. No responsibility is assumed by Schneider Electric for any consequences arising out of the use of this material. A qualified person is one who has skills and knowledge related to the construction, installation, and operation of electrical equipment and has received safety training to recognize and avoid the hazards involved B-001 5

6 kva Important Safety Information Safety Precautions DANGER HAZARD OF ELECTRIC SHOCK, EXPLOSION OR ARC FLASH The product must be installed according to the specifications and requirements as defined by Schneider Electric. It concerns in particular the external and internal protections (upstream circuit breakers, battery circuit breakers, cabling, etc.) and environmental requirements. No responsibility is assumed by Schneider Electric if these requirements are not respected. After the UPS system has been electrically wired, do not start up the system. Start-up must only be performed by Schneider Electric. Failure to follow these instructions will result in death or serious injury. DANGER HAZARD OF ELECTRIC SHOCK, EXPLOSION OR ARC FLASH The UPS System must be installed according to local and national regulations. Install the UPS according to: IEC (including protection against electric shock, protection against thermal effect, and protection against overcurrent), or NEC NFPA 70 depending on which one of the standards apply in your local area. Failure to follow these instructions will result in death or serious injury. DANGER HAZARD OF ELECTRIC SHOCK, EXPLOSION OR ARC FLASH Install the UPS system in a temperature controlled area free of conductive contaminants and humidity. Install the UPS system on a non-inflammable, level and solid surface (e.g. concrete) that can support the weight of the system. Failure to follow these instructions will result in death or serious injury. DANGER HAZARD OF ELECTRIC SHOCK, EXPLOSION OR ARC FLASH The UPS is not designed for and must therefore not be installed in the following unusual operating environments: Damaging fumes Explosive mixtures of dust or gases, corrosive gases, or conductive or radiant heat from other sources Moisture, abrasive dust, steam or in an excessively damp environment Fungus, insects, vermin Salt-laden air or contaminated cooling refrigerant Pollution degree higher than 2 according to IEC Exposure to abnormal vibrations, shocks, and tilting Exposure to direct sunlight, heat sources, or strong electromagnetic fields Failure to follow these instructions will result in death or serious injury B-001

7 Important Safety Information kva HAZARD OF OVERHEATING WARNING Respect the space requirements around the UPS system and do not cover the product s ventilation openings when the UPS system is in operation. Failure to follow these instructions can result in death, serious injury, or equipment damage. HAZARD OF EQUIPMENT DAMAGE WARNING Do not connect the UPS output to regenerative load systems including photovoltaic systems and speed drives. Failure to follow these instructions can result in death, serious injury, or equipment damage B-001 7

8 kva Technical Data Technical Data Model List EPS kva EPS kva EPS kva EPS kva EPS kva EPS kva EPS kva Input Power Factor UPS Rating 25% load 50% load 75% load 100% load 555 kva/500 kw kva//562 kw kva/675 kw kva/720 kw kva/900 kw kva/990 kw V V V Contact Schneider Electric for enhanced input power factor options. Efficiency in Normal Operation UPS Rating 25% load 50% load 75% load 100% load 555 kva/500 kw 88.7% 93.0% 93.2% 93.1% 625 kva//562 kw 92.4% 93.5% 93.3% 93% 750 kva/675 kw 92.0% 94.0% 94.2% 94.0% 800 kva/720 kw 92.0% 94.0% 94.0% 93.9% 1000 kva/900 kw 90.1% 92.2% 92.1% 91.4% 1000 kva/1000 kw 575 V 90.70% 93.20% 93.80% 93.90% 1000 kva/1000 kw 600 V 91.00% 93.60% 94.00% 93.90% 1100 kva/990 kw 90.1% 92.2% 92.0% 91.0% 1100 kva/1100 kw 575 V 91.70% 93.40% 93.80% 93.80% 1100 kva/1100 kw 600 V 91.50% 93.80% 94.00% 93.70% 480 V 87.58% 93.60% 93.74% 93.43% 575 V 91.70% 93.40% 93.80% 93.80% 600 V 91.50% 93.80% 94.00% 93.70% B-001

9 Technical Data kva Efficiency Curves 555 kva/500 kw 625 kva/562 kw B-001 9

10 kva Technical Data 750 kva/675 kw 800 kva/720 kw 1000 kva/900 kw B-001

11 Technical Data kva 1100 kva/990 kw B

12 kva Technical Data Derating due to Load Power Factor 625 kva/562 kw line voltage PF kva Lagging Unity Leading kva/720 kw line voltage PF kva Unity Leading B-001

13 Technical Data kva 1000 kva/900 kw line voltage PF kva Unity Leading kva/990 kw line voltage PF kva Unity Leading B

14 kva Technical Data line voltage PF kva Unity Leading Batteries Efficiency DC to AC 555 kva/ 500 kw 625 kva/ 562 kw 750 kva/ 675 kw 800 kva/ 720 kw 1000 kva/ 900 kw 1100 kva/ 990 kw Efficiency at nominal battery voltage (%) Battery Run-Times Schneider Electric Qualified VRLA Batteries NOTE: These battery runtimes are approximations calculated from battery manufacturer data. Please consult Schneider Electric for details. Variables such as site installation, battery condition, temperature and power factor will cause deviations from these runtimes. Battery Cabinet with GNB S12V370(F) 0.9 PF 3 Strings 4 Strings 5 Strings 6 strings 1 kva Minutes Minutes Minutes Minutes 555 kva kva kva kva kva kva Contact Schneider Electric regarding six string configurations B-001

15 Technical Data kva Battery Cabinet with EnerSys 12HX PF 3 Strings 4 Strings 5 Strings 6 strings 2 kva Minutes Minutes Minutes Minutes Battery Cabinet with GNB S12V PF 3 Strings 4 Strings 5 Strings 6 strings 2 kva Minutes Minutes Minutes Minutes Battery Cabinet w/c&d Technologies UPS12-300MR 0.9 PF 3 Strings 4 Strings 5 Strings kva Minutes Minutes Minutes Battery Cabinet w/c&d Technologies UPS12-400MR 0.9 PF 3 Strings 4 Strings 5 Strings 6 strings 2 kva Minutes Minutes Minutes Minutes Battery Cabinet w/c&d Technologies UPS12-490MR 0.9 PF 3 Strings 4 Strings 5 Strings 6 strings 2 kva Minutes Minutes Minutes Minutes Contact Schneider Electric regarding six string configurations B

16 kva Technical Data 0.9 PF 3 Strings 4 Strings 5 Strings 6 strings 3 kva Minutes Minutes Minutes Minutes Battery Cabinet w/enersys 12HX PF 3 Strings 4 Strings 5 Strings kva Minutes Minutes Minutes Battery Cabinet w/ Enersys 12HX PF 3 Strings 4 Strings 5 Strings 6 strings 3 kva Minutes Minutes Minutes Minutes Battery Cabinet w/ GNB S12V285(F) 0.9 PF 3 Strings 4 Strings 5 Strings kva Minutes Minutes Minutes Battery Material Safety Data Sheet NOTE: For Material Safety Data Sheet (MSDS), go to the Knowledge Base and type MSDS to get the latest MSDS information. 3. Contact Schneider Electric regarding six string configurations B-001

17 Technical Data Communication and Management kva Auxiliary Wiring Drawings are published for reference only and are subject to change without notice. Contact Schneider Electric for installation details B

18 kva Technical Data Compliance Regulatory Approvals Seismic Standard Warranty cul Listed UL 1778 OSHPD FCC rules and regulations of Part 15, subpart J, class A IEEE /ANSI C , Standards for Surge Withstand ability ISO 9001 Quality Standard IBC year repair or replace B-001

19 Facility Planning Facility Planning kva Input Specifications Input Specifications for kva Systems 555 kva/500 kw 625 kva/562 kw 750 kva/675 kw 800 kva/720 kw 480 V 600 V 480 V 600 V 480 V 600 V 480 V 600 V Connections Input voltage (V) Input frequency (Hz) THDI Nominal input current (A) 3 Maximum input current (A) 4 Input current limitation and Q1 rating (A) 5 Maximum short circuit withstand current (ka) Rectifier input fuses DC bus/ inverter input fuses 3PH + G /-15% 60 Less than 5% at full load A/600 VAC, 4 PLS Fast 1 KA/600 VAC, 4 PLS Fast 700 A/600 VAC, 4 PLS Fast 1.0 KA 550 VAC, 4 PLS Fast Input Specifications for kva Systems 1000 kva/ 900 kw 1000 kva/ 1000 kw 1000 kva/ 1000 kw 1100 kva/ 990 kw 1100 kva/ 1100 kw 1100 kva/ 1100 kw Input voltage (V) /- 15% 575 ±10% 600 ±10% /- 15% 575 ±10% 600 ±10% 480 ±10% 575 ±10% 600 ±10% Connections 3PH + G Input frequency (Hz) 60 Inrush current THDI Nominal input current (A) 3 600% of nominal input current for less than 1 cycle Less than 5% at full load Input current based on rated load and batteries fully charged. 4. Input current based on full battery recharge current, nominal voltage, and rated load. 5. Set for 150% nominal input current.programmable up to input circuit breaker rating B

20 kva Facility Planning 1000 kva/ 900 kw 1000 kva/ 1000 kw 1000 kva/ 1000 kw 1100 kva/ 990 kw 1100 kva/ 1100 kw 1100 kva/ 1100 kw Input voltage (V) /- 15% 575 ±10% 600 ±10% /- 15% 575 ±10% 600 ±10% 480 ±10% 575 ±10% 600 ±10% Maximum input current (A) 6 Input current limitation and Q1 rating (A) 7 Maximum short circuit withstand current (ka) Rectifier input fuses DC bus/ inverter input fuses KA 700 VAC fast 700 A 700 VAC fast Bypass Specifications Bypass Specifications for kva Systems 555 kva/500 kw 625 kva/562 kw 750 kva/675 kw 800 kva/720 kw 480 V 600 V 480 V 600 V 480 V 600 V 480 V 600 V Connections Input frequency (Hz) Nominal bypass current (A) Q4S circuit breaker rating (A) 3PH + N + G Input current based on full battery recharge current, nominal voltage, and rated load. 7. Set for 150% nominal input current. Programmable up to input CB rating B-001

21 Facility Planning kva Bypass Specifications for kva Systems 1000 kva/900 kw 1100 kva/990 kw Nominal bypass voltage (V) Connections Input frequency (Hz) Nominal bypass current (A) Q4S CB rating (A) PH + N + G Output Specifications Output Specifications for kva Systems 555 kva/500 kw 625 kva/562 kw 750 kva/675 kw 800 kva/720 kw Nominal output voltage (V) Connections Output voltage range Overload capacity Nominal output current (A) Output frequency (sync to mains) (Hz) Slew rate THDU (phase to phase) Output power factor Dynamic load at full load response Output voltage regulation (RMS) PH + N + G 480 V ± 5% (adjustable) 10 minutes at 125% load 60 seconds at 150% load Hz/Sec Programmable 0.5 to 2 Hz/Sec. 2% 0.9 ±5% ± 1% for 100% balanced loads, ± 2% for 100% unbalanced loads % rated B

22 kva Facility Planning 555 kva/500 kw 625 kva/562 kw 750 kva/675 kw 800 kva/720 kw Nominal output voltage (V) Q5N output circuit breaker ratings (A) Output inverter load fuses KA 600 V Fast 1.40 KA 650 V Fast Output Specifications for kva Systems Nominal output voltage (V) Connections Output voltage range Overload capacity Nominal output current (A) Output frequency (sync to mains) (Hz) 9 Slew rate THDU (phase to phase) Output power factor Dynamic load at full load response Output voltage regulation (RMS) Q5N output breaker ratings (A) Output inverter load fuses 1000 kva/ 900 kw 1000 kva/ 1000 kw 1000 kva/ 1000 kw 1100 kva/ 990 kw 1100 kva/ 1100 kw 1100 kva/ 1100 kw PH + N + G Nominal output voltage ± 5% 10 minutes at 125% 60 seconds at 150% Hz/Sec Programmable 0.5 to 2 Hz/Sec. Default = 1 Hz/Sec 2% ± 5% ± 1% for balanced loads ± 2% for 100% unbalanced loads KA 600 VAC Fast 9. Contact Schneider Electric for 50 Hz configurations % rated 6 PLS B-001

23 Facility Planning Battery Specifications kva Battery Specifications for kva Systems 555 kva/500 kw 625 kva/562 kw 750 kva/675 kw 800 kva/720 kw Type VRLA or Vented Lead Acid Nominal voltage (VDC) 480 Float voltage (VDC) End of discharge voltage 400 (VDC) 11 End voltage Battery current at full load and 480 VDC (A) Maximum current at 400 VDC (end of discharge) (A) Maximum charging power at full load (kw) Typical re-charge time 1.67 V/Cell C10 Battery Specifications for kva Systems Input voltage (V) Type Nominal voltage (VDC) Float voltage (VDC) 11 End of discharge voltage (VDC) 11 End voltage Battery current at full load and 480 VDC (A) Maximum current at 400 VDC (end of discharge) (A) 1000 kva/ 900 kw 1000 kva/ 1000 kw 1000 kva/ 1000 kw 1100 kva/ 990 kw 1100 kva/ 1100 kw 1100 kva/ 1100 kw VRLA or Vented Lead Acid V/Cell Programmable contact Schneider Electric for more information B

24 kva Facility Planning Max. charging power at full load (kw) Typical recharge time 1000 kva/ 900 kw 1000 kva/ 1000 kw 1000 kva/ 1000 kw 1100 kva/ 990 kw 1100 kva/ 1100 kw 1100 kva/ 1100 kw C10 Recommended Cable Sizes Recommended Cable Sizes for kva Systems DANGER HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH All wiring must comply with all applicable national and/or electrical codes. Failure to follow these instructions will result in death or serious injury. Cable sizes in this manual are based on table of the National Electrical Code (NEC) with the following assertions: 75 C conductors for 75 C termination Use of copper conductors Ground wires are sized in accordance with NEC Article and Table Power and control cables must be routed in separate conduits. Upstream and downstream bypass cable type and lengths must be equal for all UPSs installed in each integrated parallel system. 555 kva/500 kw 625 kva/562 kw 750 kva/675 kw 800 kva/720 kw Input 350 MCM x MCM x MCM x MCM x 6 Bypass 350 MCM x MCM x MCM x MCM x 4 Output 350 MCM x MCM x MCM x MCM x 4 Battery 500 MCM x MCM x MCM x MCM x B-001

25 Facility Planning kva Recommended Cable Sizes for kva Systems 1000 kva/ 1000 kw DANGER HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH All wiring must comply with all applicable national and/or electrical codes. Failure to follow these instructions will result in death or serious injury. Cable sizes in this manual are based on table of the National Electrical Code (NEC) with the following assertions: 75 C conductors for 75 C termination Use of copper conductors Ground wires are sized in accordance with NEC Article and Table Power and control cables must be routed in separate conduits. Upstream and downstream bypass cable type and lengths must be equal for all UPSs installed in each integrated parallel system kva/ 1000 kw 1100 kva/ 1100 kw 1100 kva/ 1100 kw 575 V 600 V 575 V 600 V 480 V 575 V 600 V Input (MCM) 5 x x x x x x x 600 Bypass (MCM) 5 x x x x x x x 400 Output (MCM) 5 x x x x x x x 400 Battery (MCM) 6 x x x x x x x 600 Physical Weights and Dimensions UPS Rating Cabinet Weight kg (lbs) Height mm (in) Width mm (in) Depth mm (in) 555 kva I/O cabinet 2820 (6200) 2083 (82) 1543 (60.75) 991 (39) UPS cabinet 2720 (6000) 2083 (82) 1543 (60.75) 991 (39) 625 kva I/O cabinet 2820 (6200) 2083 (82) 1543 (60.75) 991 (39) UPS cabinet 2720 (6000) 2083 (82) 1543 (60.75) 991 (39) 750 kva 12 I/O cabinet 3227 (7100) 2083 (82) 1543 (60.75) 991 (39) UPS cabinet 3136 (6900) 2083 (82) 1543 (60.75) 991 (39) 800 kva 12 I/O cabinet 3227 (7100) 2083 (82) 1543 (60.75) 991 (39) UPS cabinet 3136 (6900) 2083 (82) 1543 (60.75) 991 (39) 1000 kva UPS cabinet (7864) 2289 (90) 1797 (70) 1139 (44.83) UPS cabinet (9167) 2289 (90) 1797 (70) 1139 (44.83) 1100 kva UPS cabinet (7864) 2289 (90) 1797 (70) 1139 (44.83) UPS cabinet (9167) 2289 (90) 1797 (70) 1139 (44.83) 12. Contact Schneider Electric for maintenance bypass cabinet option kg (100 lbs) must be added if a maintenance bypass cabinet is provided B

26 kva Facility Planning UPS Rating Cabinet Weight kg (lbs) Height mm (in) Width mm (in) Depth mm (in) 1125 kva UPS cabinet (10020) 2289 (90) 1797 (70) 1139 (44.83) UPS cabinet (9750) (90) 1797 (70) 1139 (44.83) Auxiliary cabinets ( ) 2289 (90) 610 (24) 1139 (44.83) Maintenance bypass cabinet 612 (1350) 2289 (90) 610 (24) 1139 (44.83) Shipping Weights and Dimensions Contact Schneider Electric for exact shipping details physical details may vary depending in your selected options. UPS Rating Weight kg (lbs) Height mm (in) Width mm (in) Depth mm (in) 555 kva (12500) 2337 (92) 2261 (89) 1092 (43) 625 kva (12500) 2337 (92) 2261 (89) 1092 (43) 750 kva (14600) 2337 (92) 2261 (89) 1092 (43) 800 kva (14600) 2337 (92) 2261 (89) 1092 (43) 1000 kva (17827) 2388 (94) 3658 (144) 1219 (48) 1100 kva (17827) 2388 (94) 3658 (144) 1219 (48) 1125 kva (19770) (94) 3658 (144) 1219 (48) kg (100 lbs) must be added if a maintenance bypass cabinet is provided kg (10600 lbs) for 575 V and 600 V systems 16. Shipped in two cabinets kg (20620 lbs) for 575 V and 600 V systems B-001

27 Facility Planning kva Clearance NOTE: Clearance dimensions are published for airflow and service access only. Consult with the local safety codes and standards for additional requirements in your local area. NOTE: No rear service access required. Rear space requirement is 51 mm (2 in) in systems with seismic bracket and 13 mm (0.5 in) without seismic bracket B

28 kva Facility Planning Environmental Operating temperature Storage temperature Humidity Operating elevation Storage elevation Audible noise at 100% load UPS recommended: 20 to 25 C (68 to 77 F) at sea level UPS extreme: 30 C (86 F) at sea level with redundant fan UPS: -20 to 50 C ( -4 to 122 F) Battery -17 to 45 C ( 0 to 113 F) Higher storage temperature decreases battery storage life 0-95% non-condensing No derating < 3000 feet See elevation derating table below feet ( meters) Measured 5 feet from front of unit: 555 kva: 74 dba 625 kva: 74 dba 750 kva: 78 dba 800 kva: 78 dba Measured 5 feet from front of unit: 1000 kva: 76.5 dba 1100 kva: 76.5 dba 1125 kva: 76.5 dba Colour Light grey (RAL 9002) Elevation Derating Table Elevation in Feet Power Rating Multiplier Heat Dissipation Heat Dissipation for kva Systems Heat dissipation (BTU/hr) 555 kva/ 500 kw 625 kva/ 562 kw 750 kva/ 675 kw 800 kva/ 720 kw Heat Dissipation for kva Systems 1000 kva/ 900 kw 1000 kva/ 1000 kw 1100 kva/ 990 kw 1100 kva/ 1100 kw 480 V 575/600 V 480 V 575/600 V 480 V 575/600 V Heat dissipation (BTU/hr) B-001

29 Drawings Drawings kva NOTE: A comprehensive set of drawings is available on the engineering website at engineer.apc.com. NOTE: These drawings are for reference ONLY subject to change without notice B

30 kva Drawings EPS kva Single Module with Internal Bypass B-001

31 Drawings EPS kva with Maintenance Bypass Cabinet kva B

32 kva Drawings EPS kva Bottom Feed B-001

33 Drawings EPS kva Top Feed kva B

34 kva Drawings EPS 1100 kva with Maintenance Bypass Cabinet Bottom Feed B-001

35 Drawings EPS 1100 kva with Maintenance Bypass Cabinet Top Feed kva B

36 kva Options Options Hardware Options Management MultiSlot DIN - Extension Module for Com Card U-Talk/Basic Acquisition Card MultiSlot NEMA HID SNMP/Web Card Environment Sensor for Network Management Cable Configuration Options Output distribution Battery monitoring Graphical user interface with network connection Continuous duty and momentary duty static switch cabinet Critical synchronization module Ground fault detection Battery cabinet Input isolation transformer External maintenance bypass B-001

37 Schneider Electric Limited Factory Warranty Schneider Electric Limited Factory Warranty kva Three Phase Power Products or Cooling Solutions One- Year Factory Warranty The limited warranty provided by Schneider Electric in this Statement of Limited Factory Warranty applies only to products you purchase for your commercial or industrial use in the ordinary course of your business. Terms of Warranty Schneider Electric warrants that the product shall be free from defects in materials and workmanship for a period of one year from the date of product start-up when start-up is performed by Schneider Electric-authorized service personnel and occurs within six months of the Schneider Electric shipment date. This warranty covers repairing or replacing any defective parts including on-site labor and travel. In the event that the product fails to meet the foregoing warranty criteria, the warranty covers repairing or replacing defective parts at the sole discretion of Schneider Electric for a period of one year from the shipment date. For Schneider Electric cooling solutions, this warranty does not cover circuit breaker resetting, loss of refrigerant, consumables, or preventive maintenance items. Repair or replacement of a defective product or part thereof does not extend the original warranty period. Any parts furnished under this warranty may be new or factoryremanufactured. Non-transferable Warranty This warranty is extended to the first person, firm, association or corporation (herein referred to by You or Your ) for whom the Schneider Electric product specified herein has been purchased. This warranty is not transferable or assignable without the prior written permission of Schneider Electric. Assignment of Warranties Schneider Electric will assign you any warranties which are made by manufacturers and suppliers of components of the Schneider Electric product and which are assignable. Any such warranties are assigned AS IS and Schneider Electric makes no representation as to the effectiveness or extent of such warranties, assumes no responsibility for any matters which may be warranted by such manufacturers or suppliers and extends no coverage under this Warranty to such components. Drawings, Descriptions Schneider Electric warrants for the warranty period and on the terms of the warranty set forth herein that the Schneider Electric product will substantially conform to the descriptions contained in the Schneider Electric Official Published Specifications or any of the drawings certified and agreed to by contract with Schneider Electric if applicable thereto ( Specifications ). It is understood that the B

38 kva Schneider Electric Limited Factory Warranty Specifications are not warranties of performance and not warranties of fitness for a particular purpose. Exclusions Schneider Electric shall not be liable under the warranty if its testing and examination disclose that the alleged defect in the product does not exist or was caused by end user or any third person misuse, negligence, improper installation or testing. Further, Schneider Electric shall not be liable under the warranty for unauthorized attempts to repair or modify wrong or inadequate electrical voltage or connection, inappropriate on-site operation conditions, corrosive atmosphere, repair, installation, start-up by non-schneider Electric designated personnel, a change in location or operating use, exposure to the elements, Acts of God, fire, theft, or installation contrary to Schneider Electric recommendations or specifications or in any event if the Schneider Electric serial number has been altered, defaced, or removed, or any other cause beyond the range of the intended use. THERE ARE NO WARRANTIES, EXPRESS OR IMPLIED, BY OPERATION OF LAW OR OTHERWISE, OF PRODUCTS SOLD, SERVICED OR FURNISHED UNDER THIS AGREEMENT OR IN CONNECTION HEREWITH. SCHNEIDER ELECTRIC DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY, SATISFACTION AND FITNESS FOR A PARTICULAR PURPOSE. SCHNEIDER ELECTRIC EXPRESS WARRANTIES WILL NOT BE ENLARGED, DIMINISHED, OR AFFECTED BY AND NO OBLIGATION OR LIABILITY WILL ARISE OUT OF, SCHNEIDER ELECTRIC RENDERING OF TECHNICAL OR OTHER ADVICE OR SERVICE IN CONNECTION WITH THE PRODUCTS. THE FOREGOING WARRANTIES AND REMEDIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES AND REMEDIES. THE WARRANTIES SET FORTH ABOVE CONSTITUTE SCHNEIDER ELECTRIC SOLE LIABILITY AND PURCHASER S EXCLUSIVE REMEDY FOR ANY BREACH OF SUCH WARRANTIES. SCHNEIDER ELECTRIC WARRANTIES RUN ONLY TO PURCHASER AND ARE NOT EXTENDED TO ANY THIRD PARTIES. IN NO EVENT SHALL SCHNEIDER ELECTRIC, ITS OFFICERS, DIRECTORS, AFFILIATES OR EMPLOYEES BE LIABLE FOR ANY FORM OF INDIRECT, SPECIAL, CONSEQUENTIAL OR PUNITIVE DAMAGES, ARISING OUT OF THE USE, SERVICE OR INSTALLATION, OF THE PRODUCTS, WHETHER SUCH DAMAGES ARISE IN CONTRACT OR TORT, IRRESPECTIVE OF FAULT, NEGLIGENCE OR STRICT LIABILITY OR WHETHER SCHNEIDER ELECTRIC HAS BEEN ADVISED IN ADVANCE OF THE POSSIBILITY OF SUCH DAMAGES, SPECIFICALLY, SCHNEIDER ELECTRIC IS NOT LIABLE FOR ANY COSTS, SUCH AS LOST PROFITS OR REVENUE, LOSS OF EQUIPMENT, LOSS OF USE OF EQUIPMENT, LOSS OF SOFTWARE, LOSS OF DATA, COSTS OF SUBSTITUANTS, CLAIMS BY THIRD PARTIES, OR OTHERWISE. NO SALESMAN, EMPLOYEE OR AGENT OF SCHNEIDER ELECTRIC IS AUTHORIZED TO ADD TO OR VARY THE TERMS OF THIS WARRANTY. WARRANTY TERMS MAY BE MODIFIED, IF AT ALL, ONLY IN WRITING SIGNED BY AN SCHNEIDER ELECTRIC OFFICER AND LEGAL DEPARTMENT. Warranty Claims Customers with warranty claims issues may access the SCHNEIDER ELECTRIC worldwide customer support network through the SCHNEIDER ELECTRIC web site: ELECTRIC.com/support/contact/. Select your country from the country selection pull-down menu. Open the Support tab at the top of the web page to obtain contact information for customer support in your region B-001

39

40 Printed in. Schneider Electric Schneider Electric 35 rue Joseph Monier Rueil Malmaison France + 33 (0) As standards, specifications, and design change from time to time, please ask for confirmation of the information given in this publication Schneider Electric. All rights reserved B-001