POWER STATION INSTRUCTION MANUAL

Transcription

1 POWER STATION INSTRUCTION MANUAL Cat. # VG11AU September 2016 RD Printed in China 12 1 VG11AU_Manual_ indd /12/ :01:17 PM

2 INSTRUCTION MANUAL INTENDED USE Your Black & Decker power station is designed to provide additional power to lead-acid batteries when starting car engines, the cordless compressor is designed inflate car tyres and sports equipment. The inverter is designed to convert direct current (dc) to alternating current (ac) to operate equipment that is normally supplied from a mains power source. This product is intended for household, consumer use only. SAFETY INSTRUCTIONS Warning! When using battery-powered appliances, basic safety precautions, including the following, should always be followed to reduce the risk of fire, leaking batteries, personal injury and material damage. Read all of this manual carefully before using the appliance. The intended use is described in this manual. The use of any accessory or attachment or the performance of any operation with this appliance other than those recommended in this instruction manual may present a risk of personal injury. Retain this manual for future reference. Using your appliance Always take care when using the appliance. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. The appliance is not to be used as a toy. Use in a dry location only. Do not allow the appliance to become wet. Do not immerse the appliance in water. Do not open body casing. There are no userserviceable parts inside. Do not operate the appliance in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. To reduce the risk of damage to plugs and cords never pull the cable to remove the plug from a socket. Always have protective eyewear when using this product: contact with battery acid may cause blindness and/or severe burns. Be aware of first aid procedures in case of accidental contact with battery acid. Have plenty of fresh water and soap nearby in case battery acid contacts skin. If battery acid contacts skin or clothing, wash immediately with soap and water for at least 15 minutes and get medical attention immediately. 3 Never smoke or allow a spark or flame in vicinity of vehicle battery, engine or this unit. Remove personal metal items such as rings, bracelets, necklaces and watches when working with a lead acid battery. A lead acid battery can produce a short circuit current high enough to weld a ring, or similar metal object, to skin, causing a severe burn. Place this unit as far away from the battery as cables permit. Never allow battery acid to come in contact with this unit. Do not operate this unit in a closed area or restrict ventilation in any way. After use When not in use, the appliance should be stored in a dry, well ventilated place out of the reach of children. Children should not have access to stored appliances. When the appliance is stored or transported in a vehicle it should be placed in the boot or restrained to prevent movement following sudden changes in speed or direction. The appliance should be protected from direct sunlight, heat and moisture. Inspection and repairs Before use, check the appliance for damaged or defective parts. Check for breakage of parts, damage to switches and any other conditions that may affect its operation. Do not use the appliance if any part is damaged or defective. Have any damaged or defective parts repaired or replaced by the manufacturer. Never attempt to remove or replace any parts other than those specified in this manual. The following symbols are marked on the appliance: Read all of this instruction manual carefully. Reverse polarity indicator. The unit is intended for indoor use only. Specific safety instructions for jump starters Vehicles may have electrical and electronic systems (e.g. engine management system, mobile phone) that may be damaged if subjected to high starting voltages and voltage peaks. Before connecting the appliance to the vehicle read the vehicle s owner s VG11AU_Manual_ indd 2-3

3 manual to confirm that external-starting assistance is allowed. Follow these instructions and those published by the battery manufacturer, vehicle manufacturer and manufacturer of any equipment you intend to use with this unit. Review warning labels on these products and on the vehicle. This appliance is not designed to be used as a replacement for a vehicular battery. Do not attempt to operate a vehicle that does not have a battery installed. The appliance must only be connected to a 12V leadacid battery. Do not use the appliance for charging dry-cell batteries that are commonly used with home appliances. These batteries may burst and cause injury to persons and damage property. Check the polarity of the vehicle battery terminals before connecting the appliance. Always disconnect the negative (black) jumper cable first: followed by the positive (red) jumper cable. The jump-starter power switch should be in the off position before connection to a power source or load, when the unit is charging and when not in use. Never allow the red and black clamps to touch each other or another common metal conductor. This could cause damage to the appliance and/or create a sparking/explosion hazard. Always store the battery clamps in the built-in holders when not in use. When using this unit in proximity to the vehicle s battery and engine, stand the unit on a flat, stable surface, and be sure to keep all clamps, cords, clothing and body parts away from moving parts of the vehicle. This appliance contains a sealed lead-acid battery. It is recommended that the appliance is laid flat during storage, use, and recharging. Excessive engine cranking can damage a vehicle s starter motor. If the engine fails to start after the recommended number of attempts, discontinue jump-start procedures and look for other problems that may need to be corrected. Do not charge the appliance using the 12V DC charging adapter when the vehicle is occupied. Never attempt to use the mains and 12V DC charging adapter simultaneously. Do not use this jump-starter on a watercraft. It is not qualified for marine applications. Warning! Burst hazard: Do not use the unit for charging dry-cell batteries that are commonly used with home appliances. These batteries may burst and cause injury to persons and damage property. Use the unit for charging/boosting a lead-acid battery only. It is not intended to supply power to a lowvoltage electrical system other than in a starter-motor application. Warning! Explosive gas may be vented from lead acid batteries when charging. The battery must be placed in a well-ventilated area and you must remove any sources of ignition when conducting jump starting procedures. To reduce the risk of electric shock, disconnect the appliance from any power source before attempting maintenance or cleaning. Turning off controls without disconnecting the appliance will not reduce this risk. Make sure the appliance is disconnected from all charging power sources before beginning the jump start procedure. Additional safety warnings for compressors For home and car use only. Inflate car and bike tyres, balls, rafts, swimming pool floats, air mattresses, and more in and around the home. Do not operate the compressor continuously for extended periods of time (approximately 10 minutes, depending on ambient temperatures), as it may overheat. In this event, the compressor will automatically shut down. Immediately turn off the compressor power switch. Restart the compressor after a cooling down period of approximately 30 minutes. The compressed air from your compressor is not safe for breathing. Never inhale air from your compressor or from a breathing device connected to the compressor. Inflate items only to their manufacturer s recommendations. Exceeding the pressure rating could cause them to explode resulting in personal injury. Do not leave compressor running unattended. It could burst tyres or other items. Since the vibration produced by the compressor may cause it to walk, do not operate on a high shelf or other surface. Operate at ground or bench level. Do not modify or attempt to repair. Never drill into, weld, or make any modifications to the compressor or its attachments. Do not operate compressor when the car engine is running. Operate only with the accessories included or those rated for 8.28 bar/120 p.s.i. or higher. The use of any accessory not recommended for use with this tool could be hazardous. Do not play with the tool. High pressure air is dangerous. Don t direct air-flow at yourself or others. The compressor can become hot during use. Allow compressor to cool for 30 minutes before storing away. Never carry the compressor by the hose. This tool is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance. Specific safety instructions for power inverters Warning! This appliance converts power from 12V DC battery to V AC mains supply voltage. Take precautions, including the following, to avoid the risk of electric shock. Always turn the inverter off when not in use. Only connect a plug fitted to the supply cord of an appliance to the inverter. Never connect an appliance by modifying the plug or by using an adapter. Never connect an appliance that is damaged or incomplete. Never connect the inverter to the output of another inverter. Remove the appliance plug from the inverter before performing any maintenance or before cleaning the appliance. Do not cover the inverter. Only use in well ventilated areas. Do not open the inverter, there are no serviceable parts inside. Do not probe the inverter. Check that connections to the DC supply are clean and secure. Loose connectors may cause overheated wires and melted insulation. Do not install in engine compartments. Do not use the inverter to supply any medical devices. Warning! Rechargeable devices: Some rechargeable devices do not operate well from a modified sine wave inverter. They only operate correctly from a standard household outlet which provides a pure sine wave. Therefore, the manufacturer recommends that you operate these types of devices from a standard household outlet only, not from the inverter. This problem does not occur with the majority of battery-operated equipment. Most of these devices use a separate charger or transformer that is plugged into an AC mains socket. The inverter is easily capable of running most chargers and transformers. Caution! Incompatible products: Certain products contain power supplies or circuits that are not compatible with an inverter using a modified sine wave output (such as this inverter) and may be damaged by using this inverter. Some products must be powered from a pure sine wave power source, such as standard household power, or a pure sine wave inverter in order to function properly. If your product requires pure sine wave AC input power to function properly, the instruction manual for your product could state this. If in doubt, you should contact your product manufacturer PRIOR TO USE. Your product could be damaged by this inverter if it contains: Microwave ovens Transformerless battery chargers Capacitive coupled power supplies If an incompatible product is used with this inverter: The product might not operate at all, with no indication of failure. The product fuse might open as a result of trying to use it with the inverter. The product might exhibit unusual operation (such as, intermittent operation, buzzing, and the like.) Some USB-powered household electronics may not operate with this USB socket. Check the manual of the corresponding electronic device to confirm that it can be used with this type of USB socket. Warning! This appliance will not operate high wattage appliances or equipment that produce heat, such as coffee makers, hair dryers, microwave ovens, and toasters. Note: Some laptop computers may not operate with this inverter. RATED VERSUS ACTUAL POWER REQUIREMENTS OF EQUIPMENT Most electrical tools, appliances and audio/video equipment have labels that indicate the power consumption in amps or watts. Be sure that the power consumption of the item you wish to operate is rated at 200 watts or less. The power inverter is fitted with overload protection and will shutdown if a load in excess of 200 W is applied. Resistive loads (i.e incandescent lights) are the easiest for the power inverter to run. Additional safety instructions for batteries and chargers BATTERIES Never attempt to open for any reason. Do not expose the battery to water. Do not store in locations where the temperature may exceed 40 C. Charge only at ambient temperatures between 4 C and 40 C. Charge only using the chargers provided with the appliance. When disposing of batteries, follow the instructions given in the section Protecting the environment. 4 5 VG11AU_Manual_ indd 4-5

4 Under extreme conditions, battery leakage may occur. When you notice liquid on the batteries, carefully wipe the liquid off using a cloth. Avoid skin contact. CHARGERS The following symbols are found on your mains charger: Your charger is double insulated; therefore no earth wire is required. Your charger is a switch mode power supply unit. Your charger incorporates a short-circuit-proof safety isolating transformer (inherently or non-inherently) Indication of correct connection of your charger. The charger is intended for indoor use only. Your charger meets the Energy Efficiency Level V standard for no-load condition electric power consumption and average active efficiency of external power supplies. Your charger is rated to IP20 degree of protection provided by the enclosure. Your charger has been designed for a specific voltage. Always check that the mains voltage corresponds to the voltage on the rating plate. Warning! Never attempt to replace the charger unit with a regular mains plug. Use your Black & Decker charger only to charge the battery in the tool with which it was supplied. Other batteries could burst, causing personal injury and damage. Never attempt to charge non-rechargeable batteries. Have defective cords replaced immediately. Do not expose the charger to water. Do not open the charger. Do not probe the charger. The battery must be placed in a well ventilated area when charging. Electrical safety Always check that the power supply corresponds to the voltage on the rating plate. The supply cord cannot be replaced. If the cord is damaged the appliance should be scrapped. PERSONAL SAFETY Always have protective eyewear when using this product: contact with battery acid may cause blindness and/or severe burns. Be aware of first aid procedures in case of accidental contact with battery acid. Avoid touching the eyes while working with a battery. Acid, acid particles or corrosion may get into the eyes. Have plenty of fresh water and soap nearby in case battery acid contacts skin. Remove personal metal items such as rings, bracelets, necklaces and watches when working with a lead-acid battery. A lead-acid battery can produce a short circuit current high enough to cause a severe burn. Be extra cautious to reduce the risk of dropping a metal object onto the battery. This might cause sparks or short-circuit the battery or other electrical part, which can cause an explosion. Warning! Battery fluid is a diluted sulphuric acid and may cause personal injury or damage to property. In case of skin or eye contact, follow the instructions below. In case of skin contact, immediately rinse with water. If redness, pain or irritation occurs seek medical attention. In case of eye contact, rinse immediately with clean water and seek immediate medical attention. FEATURES 1. Mains socket 2. USB power button 3. USB power port (under protective cover) 4. 12V DC accessory socket (under protective cover) 5. USB power indicator 6. Battery status LED indicators 7. Reverse polarity indicator 8. Jump-starter on/off switch 9. Pivoting LED area light power switch 10. Pivoting LED area light 11. Battery power level button 12. Inverter power indicator & inverter power switch 13. Charging socket 14. Air pressure gauge 15. Positive (+) red clamp 16. Air hose and SureFit nozzle connector 17. Compressor power switch 18. Negative ( ) black clamp 19. DC charging adapter (optional accessory) 20. Nozzle adapter 21. Mains charging adapter USE Charging the unit This unit is shipped in a partially charged state. Charge the unit before first use using the mains charging adapter for 40 hours. Lead-acid batteries require routine maintenance to ensure a full charge and a long battery life. All batteries lose energy from self-discharge over time and more rapidly at higher temperatures. When the unit is not in use, Black & Decker recommend that the battery is charged at least every 30 days. Check the battery charge level by pressing the battery status pushbutton. The LED charge status display will indicate the level of battery charge. When only one red LED lights, charge the unit. Make sure all other unit functions are turned off during recharging, as this can slow the recharging process. Note: Charging the battery after each use will prolong the battery life; frequent heavy discharges between charges and/or overcharging will reduce battery life. Important! When the battery is overly discharged and if the green LED is lit when the charger is plugged in, this indicates the battery is at a high impedance stage. In this event, recharge the unit and leave the unit charging for a period of hours before use. CHARGING THE UNIT USING THE MAINS CHARGING ADAPTER Insert the jack of the mains charging adapter into the charging socket on the back of the unit. Insert the appropriate mains charging adapter plug into a mains power socket. Charge until two red and one green (full) battery status LEDs light or flash. Continue to charge for one to two more hours. Once fully charged disconnect the Mains charging adapter from the mains power socket and then remove the jack plug of Mains charging adapter from the charging socket on the back of the unit. Store it in a safe place. CHARGING THE UNIT USING THE DC CHARGING ADAPTER (OPTIONAL ACCESSORY) Charging the unit from an external 12 volt DC power source requires the use of the 12V DC charging adapter. This adapter has a male DC connector at each end. Insert the gold-tipped plug of the 12V DC charging adapter into the accessory socket socket of your vehicle or other 12V DC power source. Insert the silver-tipped plug into the 12V DC accessory socket on the front panel of the unit. 6 7 Charge the unit until the green (full) battery status LED lights when the battery power level button is pressed (AFTER unplugging the adapter from the unit). When charging is complete, disconnect the 12V DC charging adapter and store it in a safe place. Note: Some vehicles require that the ignition be switched to the accessory socket position in order to power the accessory socket. Caution! To reduce the risk of property damage: Recharge using this method only when necessary. Frequent use the the 12 volt DC charging method may shorten battery life. Do not charge for longer than 6 hours maximum using this method and do not leave the unit unattended when charging using this method. Never connect the 12V DC charging adapter to a positive grounded vehicle. The 12V DC charging adapter must only be connected to batteries with a nominal output voltage of 12 volts. The unit will not operate from a 6 volt battery and will sustain permanent damage if connected to a 24 volt battery. Using the unit as a jump-starter Warning! Make sure that the vehicle is in neutral with the parking brake applied. Warning! Make sure that the cables are not in the path of moving belts or the fan. 1. Turn off the vehicle s ignition and all accessories before making any connections. 2. Make sure that the jump-starter power switch is turned off. 3. Check polarity of battery posts. Positive (POS, P, +) battery post usually has larger diameter than negative (NEG, N, ) post. 4. Determine which post of the battery is grounded (connected to the chassis). If negative post is grounded (as in most vehicles), see 5. If positive post is grounded, see For negative-grounded vehicle, connect positive (red) clamp from battery charger to positive (POS, P, +) ungrounded post of battery. Connect negative (black) clamp to vehicle chassis or engine block away from battery. Do not connect clip to carburetor, fuel lines, or sheet-metal body parts. Connect to heavy gauge metal part of the frame or engine block. 6. For positive-grounded vehicle, connect negative (black) clamp from battery charger to negative (NEG, N, ) ungrounded post of battery. Connect positive (red) clamp to vehicle chassis or engine block away from battery. Do not connect clip to carburetor, fuel lines or sheet-metal body parts. Connect to a heavy gauge metal part of the frame or engine block. VG11AU_Manual_ indd 6-7

5 Important! If the connections to the battery s positive and negative terminals are incorrect, the Reverse Polarity Indicator will light and the unit will sound a continuous alarm until the clamps are disconnected. Disconnect clamps and reconnect to battery with correct polarity. 7. Turn the jump-starter power switch to the on position. 8. Start the vehicle and crank the engine in 3 to 6 second bursts. Important! If the engine doesn t start within 6 seconds let the units internal battery cool for 3 minutes before making another attempt. 9. When the vehicle starts, turn the jump-starter on/ off switch to the off position. 10. Leave the vehicle s engine running. 11. Disconnect the clamp connected to the engine block or chassis first, followed by the clamp that is connected to the positive (+) battery terminal. Recharge this unit fully after each use. Using the pivoting LED area light The pivoting area light is controlled by the area light power switch on top of the light. Make sure the area light is turned off when the unit is being recharged or stored. Periodically press the battery power level button to check battery status. Using the portable compressor The built-in 12 volt DC compressor is the ultimate compressor for all vehicle tyres, trailer tyres and recreational inflatables. The compressor can operate long enough to fill up to 3 average sized tyres before the battery must be recharged. INFLATING TYRES OR PRODUCTS WITH VALVE STEMS 1. Screw the SureFit nozzle onto the valve stem. Do not overtighten. 2. Turn on the compressor power switch. 3. Check pressure with the pressure gauge. 4. When desired pressure is reached, turn off the compressor power switch. 5. Unscrew and remove the SureFit nozzle from the valve stem. 6. Allow the unit to cool, then recharge before storing away. 7. Store the compressor hose and SureFit nozzle in the storage compartment. INFLATING OTHER INFLATABLES WITHOUT VALVE STEMS Inflation of other items requires use of the nozzle adapter. 1. Screw the adapter into the SureFit nozzle. Do not overtighten. 2. Insert the adapter into item to be inflated. 3. Turn on the compressor power switch inflate to desired pressure or fullness. Important! Small items such as volleyballs, footballs, etc. inflate very rapidly. Do not overinflate. 4. When desired pressure is reached, turn off the compressor power switch. 5. Disconnect the adapter from the inflated item. 6. Unscrew and remove the adapter from the SureFit nozzle. 7. Allow the unit to cool, then recharge before storing away. 8. Store the compressor hose, SureFit nozzle and adapter in the storage compartment. Recharge this unit fully after each use. Using the mains socket Press the inverter power switch to turn the inverter on. The inverter power indicator will light red to indicate the mains socket is ready to use. Simply plug the volt AC appliance into the unit s mains socket and operate normally. Periodically check the unit s battery status by pressing the battery power level button. Two red and one green battery status indicators will light to indicate a full battery. If only one red battery status indicator lights it indicates that the unit needs to be recharged. Note: The unit s mains socket may not operate appliances and equipment that generate heat, such as hair dryers, electric blankets, microwave ovens and toasters. Some laptop computers may not operate with the unit s mains socket. PROTECTIVE FEATURES The inverter monitors the following conditions: Low internal battery voltage: The inverter will automatically shut down when the battery voltage drops too low, as this can harm the battery. High internal battery voltage: The inverter will automatically shut down when the battery voltage is too high, as this can harm the unit. Thermal shutdown protection: The inverter will automatically shut down when the unit becomes overheated. Overload/short circuit protection: The inverter will automatically shut down when an overload or short circuit occurs. Important Notes: The inverter power indicator will flash red to indicate that one of the above fault conditions is present before automatic shutdown occurs. Should this occur, take the following steps: 1. Disconnect all appliances from the unit. 2. Press the inverter power switch to turn the inverter off. 3. Allow the unit to cool down for several minutes. 4. Make sure the wattage of all equipment simultaneously plugged into the USB and mains sockets does not exceed 200 watts continuous and that appliance cord(s) and plug(s) are not damaged. 5. Make sure there is adequate ventilation around the unit before proceeding. Using the USB socket 1. Push the USB power button to turn the USB port on. The USB power indicator will light. 2. Lift up the cover of the USB socket. 3. Plug the USB-powered device into the USB socket and operate normally. Periodically check the unit s battery status by pressing the battery power level button Notes: This unit s USB socket does not support data communication. It only provides 5 volts/2a DC power to an external USB-powered device. Some household USB-powered electronics will not operate with this unit. Make sure the USB power button is in the off position when the unit is being recharged or stored. Using the 12 volt DC power socket This portable power source is also for use with all 12 volt DC accessories equipped with a male accessory socket plug and are rated up to 5 amps. 1. Lift up the cover of the unit s 12V DC socket. 2. Insert the 12 volt DC plug from the appliance into the 12V DC accessory socket on the unit. DO NOT EXCEED A 5 AMP LOAD. 3. Switch on the appliance and operate as usual. Periodically press the battery power level button to check battery status. TROUBLESHOOTING Problem Unit will not charge Unit fails to jump-start Solution Make sure all of the unit s functions are turned off. Make sure the jack of the mains charging adapter is properly connected to both the unit and a functioning mains power socket. Make sure unit s power switch is in the on position. Check that the unit has a full charge. Recharge the unit if necessary. Make sure a proper polarity cable connection has been established. Problem LED Area Light does not come on Portable compressor will not inflate Mains outlet will not power appliance USB port will not power appliance Solution Make sure the LED area light power switch is turned on. Recharge the unit if necessary. Make sure the compressor power switch is in the on position. Make sure the SureFit nozzle connector is securely screwed on to the valve stem when attempting to inflate tires; or that the nozzle adapter is securely screwed into the SureFit nozzle connector and is inserted properly into the item to be inflated on all other inflatables. The compressor may be overheated. Press the compressor power switch to turn the compressor off. Restart after a cooling down period of approximately 30 minutes. Check that the unit has a full charge. Recharge the unit if necessary. Make sure the inverter power switch is switched on. Make sure the appliance being powered does not draw more than 200 watts. Make sure you have followed all the steps in the mains portable power supply instructions carefully. Refer to the important notes included in that section that explain common problems and solutions. Recharge the unit if necessary. Make sure the USB charging port power button is in the on position. Make sure the the appliance does not draw more than 2 amps. Some USB-powered household electronics will not operate with this USB charging/power port. Check the manual of the corresponding electronic device to confirm that it can be used with this type of USB charging/power port. Recharge unit if necessary. 8 9 VG11AU_Manual_ indd 8-9

6 Problem 12V DC accessory outlet will not power appliance Solution Make sure the the appliance does not draw more than 5 amps. Recharge unit if necessary. If the unit does not charge or operate after following the above directions, contact the manufacturer. MAINTENANCE Your Black & Decker tool has been designed to operate over a long period of time with a minimum of maintenance. Continuous satisfactory operation depends upon proper tool care and regular cleaning. Warning! Before performing any maintenance or cleaning of the tool, unplug the unit from the power supply. From time to time wipe the appliance with a damp cloth. Do not use any abrasive or solvent-based cleaner. Do not immerse the appliance in water. Clean the outside case of the battery charger with a soft cloth and, if necessary, mild soap solution. Do not allow liquid to enter the battery charger. Do not operate when the battery charger is wet. Keep the battery charger cords loosely coiled during storage to prevent damage to the cords. Replacing the fuse in the 12V DC charging adapter (optional accessory) 1. Remove the cap by turning it counterclockwise. 2. Remove the centre pin and the spring. 3. Remove the fuse. 4. Install a new fuse of the same type and size (8A). 5. Replace the centre pin and spring. 6. Secure the cap by turning it clockwise onto the plug. Do not overtighten. 7. Test for proper operation of the 12V DC charging adapter. PROTECTING THE ENVIRONMENT Correct disposal of this product This marking indicates that this product should not be disposed with other household waste throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmentally safe recycling. Separate collection of used products and packaging allows materials to be recycled and used again. Re-use of recycled materials helps prevent environmental pollution and reduces the demand for raw materials. Local regulations may provide for separate collection of electrical products from the household, at municipal waste sites or by the retailer when you purchase a new product. Lead acid batteries can be recharged many times. At the end of their useful life, discard batteries with due care for our environment: Do not dispose of the battery in fire, as this may result in an explosion. Lead acid (Pb) batteries are recyclable. They must not be disposed of with household waste. The battery must be removed and disposed of in accordance with local regulations. Do not short-circuit the battery terminals. Be aware that the battery is heavy. If possible, operate the appliance to run the battery down completely. Place the battery in a suitable packaging to ensure that the terminals cannot be short-circuited. TECHNICAL DATA Boost ampere 12V DC, 500A instantaneous Battery type Maintenance-free, sealed lead acid, 12V DC, 19Ah Area Light 1 long-life white LED USB socket 5V DC, 2A Dc accessory socket 12V DC, 5A Maximum AC output V ac, 50Hz, 200W continuous Output waveform Modified sine wave Compressor Pressure (max.) bar/p.s.i 8.27/120 Mains charging adapter Input: Output: V AC, 50/60Hz 14,5V DC, 750mA 12V DC charging adapter (optional accessory) 12V DC WARRANTY Our goods come with guarantees that cannot be excluded under the Australian & New Zealand Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. Baccus Worldwide LLC is confident of the quality of its products and offers an outstanding warranty. This warranty statement is in addition to and in no way prejudices your statutory rights under the Australian & New Zealand Consumer Law. If a Baccus Worldwide LLC product becomes defective due to faulty materials, workmanship or lack of conformity, within 24 months from the date of purchase, Baccus Worldwide LLC guarantees to replace defective parts, repair products subjected to fair wear and tear or replace such products to make sure of the minimum inconvenience to the customer unless: The product has been used for trade, professional or hire purposes; The product has been subjected to misuse or neglect; The product has sustained damage through foreign objects, substances or accidents; Repairs have been attempted by persons other than Baccus Worldwide LLC service staff. To claim on this warranty, you will need to submit proof of purchase and return the allegedly defective product to Baccus Worldwide LLC s local market distributor, at your expense. Please visit our website to register your new Baccus Worldwide LLC product and to be kept up to date on new products and special offers. Further information on the Baccus Worldwide LLC brand and our range of products is available at Distributed by: Directed Electronics Address: 44 Translink Drive, Keilor Park Victoria Australia 3042 PH: service@directed.com.au Baccus Worldwide LLC Weena 290, 3012 NJ Rotterdam or Postbus 819, 3000 AV Rotterdam +31(0) VG11AU_Manual_ indd /12/ :01:19 PM