Compact Jumpstart with Compressor Model No. JSM-0580

Transcription

1 Compact Jumpstart with Compressor Model No. JSM-0580 OWNER'S MANUAL Customer Service Tel: Superex Canada Limited, Toronto M2H 3B8 Made in China

2 IMPORTANT SAFETY INSTRUCTIONS 1. SAVE THESE INSTRUCTIONS - This manual contains important safety and operating instructions for this Jumpstart. 2. Before using Jumpstart, read all instructions and cautionary markings on Jumpstart and in this instruction manual. 3. CAUTION - To reduce risk of injury, charge only with AC adaptor and charging cord supplied. Other chargers may cause battery to burst causing injury to persons and damage. 4. Do not expose Jumpstart or chargers to rain, moisture, or snow. 5. Use of an attachment not recommended or sold by the manufacturer may result in a risk of fire, electric shock, or injury to persons. 6. To reduce risk of damage to cigarette lighter connector and cord, pull by cigarette lighter connector rather than cord when disconnecting charger. 7. Make sure cord is located so that it will not be stepped on, tripped over, or otherwise subjected to damage or stress. 8. Do not operate charger with damaged cord or cigarette lighter connector - replace it immediately. 9. Do not operate Jumpstart or charger if it has received a sharp blow, been dropped, or otherwise damaged in any way; take it to a qualified serviceperson. 10. Do not disassemble Jumpstart or charger; take it to a qualified serviceperson when service or repair is required. Incorrect reassembly may result in a risk of electric shock or fire. 11. To reduce risk of electric shock, unplug charger before attempting any maintenance or cleaning. Turning off controls will not reduce this risk. 12. The Power unit is intended to be correctly orientated in a vertical or floor position. 13. WARNING - RISK OF EXPLOSIVE GASES. a) WORKING IN VICINITY OF A LEAD-ACID BATTERY IS DANGEROUS. BATTERIES GENERATE EXPLOSIVE GASES DURING NORMAL BATTERY OPERATION. FOR THIS REASON, IT IS OF UTMOST IMPORTANCE THAT EACH TIME BEFORE USING YOUR JUMPSTARTER, YOU READ THIS MANUAL AND FOLLOW THE INSTRUCTIONS EXACTLY. b) To reduce risk of battery explosion, follow these instructions and those published by vehicle or battery manufacturer and manufacturer of any equipment you intend to use in vicinity of battery. Review cautionary marking on these products and on engine. c) DO NOT EXPOSE JUMPSTART OR BATTERY TO FIRE OR INTENSE HEAT AS IT MAY EXPLODE. 14. PERSONAL PRECAUTIONS a) Someone should be within range of your voice or close enough to come to your aid when you work near a lead-acid battery. b) Have plenty of fresh water and soap nearby in case battery acid contacts skin, clothing, or eyes. c) Wear complete eye protection and clothing protection. Avoid touching eyes while working near battery. d) If battery acid contacts skin or clothing, wash immediately with soap and water. If acid enters eye, immediately flood eye with running cold water for at least 10 minutes and get medical attention immediately. e) NEVER smoke or allow a spark or flame in vicinity of battery or engine. f) Be extra cautious to reduce risk of dropping a metal tool onto battery. It might spark or short-circuit battery or other electrical part that may cause explosion.

3 g) Remove personal metal items such as rings, bracelets, necklaces, and watches when working with a lead-acid battery. A lead-acid battery can produce a short-circuit current high enough to weld a ring or the like to metal, causing a severe burn. h) Use Jumpstarter on a 12 volt LEAD-ACID battery only. Do not connect to a 6 volt or 24 volt battery system. Use DC outlet socket to operate 12 volt appliances equipped with a cigarette lighter plug. i) NEVER jumpstart a frozen battery j) This system is not designed to be used as a replacement for a vehicular battery. Do not attempt to operate a vehicle that does not have a battery installed. 15. WARNING - FOLLOW THESE STEPS WHEN JUMPSTARTING A VEHICLE. A SPARK NEAR BATTERY MAY CAUSE BATTERY EXPLOSION. TO REDUCE RISK OF A SPARK NEAR BATTERY OR INJURY, FOLLOW PRECAUTIONS BELOW. a) Always store battery clamps on clamp holder tabs on back of unit when not in use. Never touch battery clamps together, this can cause dangerous sparks, power arcing and/ or explosion. b) Jump-start procedures should only be performed in a safe, dry, well-ventilated area. c) When using this unit in proximity to the vehicle's battery and engine, stand the unit on a flat, stable surface, and be sure to keep all clamps, cords, clothing and body parts away from moving vehicle components. d) Check polarity of battery posts. POSITIVE(POS, P,+) battery post usually has larger diameter than NEGATIVE (NEG, N, -) post. e) Determine which post of battery is grounded (connected) to the chassis. If negative post is grounded to chassis, (as in most vehicles), see (f). If positive post is grounded to the chassis, see (g). f) For negative-grounded vehicle, connect POSITIVE (RED) clip from Jumpstart to POSITIVE (POS, P, +) ungrounded post of battery. Connect NEGATIVE (BLACK) clip to vehicle chassis or engine block away from battery. Do not connect clip to carburetor, fuel lines, or sheet-metal body parts. Connect to a heavy gauge metal part of the frame or engine block. g) For positive-grounded vehicle, connect NEGATIVE (BLACK) clip from Jumpstart to NEGATIVE (NEG, N, -) ungrounded post of battery. Connect POSITIVE (RED) clip to vehicle chassis or engine block away from battery. Do not connect clip to carburetor, fuel lines, or sheet-metal body parts. Connect to a heavy gauge metal part of the frame or engine block. h) When disconnecting cables, disconnect clamp from vehicle chassis first and then remove clip from battery terminal. I) Store in a cool, dry place. Keep out of reach of children. 16. CAUTIONS - a) Vehicles that have on-board computerized systems may be damaged if vehicle battery is jump started. Before jump-starting, read the vehicle's owners manual to confirm that external-starting assistance is advised. b) Excessive engine cranking can damage a vehicle's starter motor. If the engine fails to start after the recommended number of attempts, discontinue jump-start procedures and look for other problems that may need to be corrected. FIRST AID: SKIN: If battery acid comes in contact with skin, rinse immediately with running water, then wash thoroughly with soap and water. If redness, pain or irritation occurs, seek immediate medical attention. EYES: If battery acid comes in contact with eyes, flush eyes immediately - for minimum of 10 minutes - seek immediate medical attention.

4 JUMSTART SYSTEM MUST BE FULLY CHARGED FOR 28 HOURS BEFORE FIRST USE. FAILURE TO DO SO MAY PERMANENTLY DAMAGE BATTERY. (See section on charging) WELCOME This Superex product has been carefully engineered and manufactured to give you dependable operation. Please read this manual thoroughly before operating your new product as it contains the information you need to become familiar with its features and obtain the performance that will bring you continued enjoyment for many years. Please keep this manual on file for future reference 260 PSI COMPRESSOR AND AIR HOSE RUGGED RUBBER BUMPER GUARDS FOLD DOWN HANDLE BUILT-IN BOOSTER CABLE STORAGE LED LIGHT LED LIGHT ON / OFF BATTERY TEST BUTTON DIGITAL GAS GAUGE METER+ REVERSE POLARITY INDICATOR LIGHTS MASTER SWITCH 12 VOLT POWER OUTLET SOCKET CHARGING PORT USB / COMPRESSOR ON / OFF SWITCH USB PORT

5 CHARGING THE JUMPSTART SYSTEM! CAUTION This unit has maintenance free, built in sealed lead acid battery. Although the Jumpstart System arrives partially charged from the factory, it MUST BE FULLY CHARGED FOR 28 HOURS BEFORE FIRST USE, even if the battery digital gas gauge meter+ indicates a 99% charge. This initial charge pre-conditions the battery. Failure to follow this procedure may permanently damage the battery. CHARGING WITH AC ADAPTOR Plug the AC adaptor cord into the input charging jack on the front of the unit and the adaptor into any 110 Volt AC wall outlet. The digital gas gauge meter+ will begin to flash to indicate the unit is charging. Charge for 28 hours or until battery is full. In the final stages of the charging procedure, the digital gas gauge meter+ will flash 99%. For full capacity, allow unit to continue charging for 2-3 hours. Once the AC adaptor input jack is removed from the unit, the digital gas gauge meter+ will remain illuminated for approximately 30 seconds. CHARGING WITH DC ADAPTOR Due to safety circuits built into the input charging jack, DC charging through this location will not fully charge the battery. Plug input of DC adapter plug into charging port of Jumpstart and the other end into the cigarette lighter socket of your vehicle. Green light on DC adapter outlet will illuminate and the digital gas gauge meter+ will begin to flash to indicate the unit is charging. Vehicle should be running for full charging to take place. Note: This method allows battery to be topped up during a journey but may not fully charge the unit. Disconnect charging cord before turning off engine. NEVER leave vehicle running in an enclosed or poorly ventilated space. CHARGING TIPS AND WARNINGS Keep battery power topped up, ready for emergencies. Unlike some rechargeable batteries, frequent charging will not harm and in fact, will improve the performance of the internal battery. Recharge battery as soon as possible after each use to prolong battery life. Frequent heavy discharges between recharging will reduce battery life. Do not leave Jumpstart in a total discharged state for an extended period of time as this can cause battery failure. All lead acid batteries suffer from self-discharge over time, especially under extreme temperatures. Store in a cool dry place. Recharge every 3 months when not in use and more frequently in warmer or colder storage conditions. Do not continuously charge the Jumpstart system for more than 36 hours. Use only the charging adaptors provided with this unit. DO NOT OPERATE ANY OF THIS UNITS FUNCTIONS WHILE CHARGING IS IN PROCESS.

6 BATTERY STATUS Press the Battery Test button. The digital gas gauge meter+ will illuminate to show the amount of power remaining in the Jumpstart System. Digital gas gauge meter+ will remain illuminated for approximately 30 seconds. Pressing the battery test button a second time will illuminate the PSI portion of the digital gas gauge meter+. To turn the digital gas gauge meter+ off, press the battery test button twice, the digital gas gauge meter+ will go out. 1. When the battery is fully charged, the digital gas gauge meter+ will display 99%. 2. When the battery is at about 50% capacity it should be recharged as soon as possible It will be able to operate the LED light and most 12 Volt Accessories for a limited time but will be inadequate for the Boosting function. Take care to not let the battery deep discharge as it may damage the battery. 3. When the digital gas gauge meter+ displays 25%, the battery is low and usage must be discontinued immediately. Recharge battery as soon as possible and before further use.

7 JUMPSTARTING AN ENGINE! CAUTION MAKE SURE THE ROTARY MASTER SWITCH IS IN THE O OFF POSITION. JUMPSTART MUST BE FULLY CHARGED TO JUMPSTART AN ENGINE. Do not attempt to Jumpstart an engine if the digital gas gauge meter+ does not display 99% when you press the battery test button as this could permanently damage the battery. Turn off ignition and all accessories (lights, radio, heater, air conditioning, etc.) in the vehicle with weak battery that will not start. Place vehicle in park and set hand brake. For maximum power, turn off all switches on your Jumpstart system and disconnect any accessories plugged into the 12 Volt power outlets. Check that vehicle is negatively grounded (most vehicles). Remove the cables from the side of the jumpstart channels by squeezing the clamp handle and pulling out. Securely connect the red positive clamp to the positive (+) terminal of the vehicle battery. Then, securely connect the black clamp to a grounding point on the vehicle such as the metal frame, as far away from the battery as possible. DO NOT connect it to the negative battery terminal. Make sure both clamps have good contact. Jumpstart is equipped with a Reverse Polarity indicator light. If the cables are hooked up incorrectly the red light will illuminate to provide a visual warning. If this happens, disconnect the cables and reconnect in the opposite direction. Green light should illuminate to indicate a correct hookup. NOTE: DO NOT PLACE JUMPSTART WHERE IT COULD FALL WHEN VEHICLE STARTS UP. MAKE SURE THAT CABLES ARE ROUTED AWAY FROM MOTOR FAN OR BELTS. Turn rotary switch to the " " on position and start your vehicle. Once vehicle starts, turn rotary switch to "off" position and disconnect black clamp first and then, red clamp. Restore cables in Jumpstart System and recharge unit at first opportunity. NOTE: WHEN STARTING VEHICLE, CRANK ENGINE IN 5-6 SECOND BURSTS. IF VEHICLE DOES NOT START UP WITHIN 2-3 ATTEMPTS. ALLOW THE JUMPSTART TO COOL FOR 3 MINUTES BEFORE ATTEMPTING TO START VEHICLE AGAIN. RETRY ONLY IF BATTERY CONDITION IS GREEN.

8 WARNINGS! EXPLOSION HAZARD Do not allow the positive and negative booster clamps of the Jumpstart System to come into contact with each other (or a common piece of metal) at any time. Sparking, an explosion, or damage to the unit may result. When jumpstarting a vehicle, make sure that the positive and negative booster clamps are properly connected to the vehicle and battery. Failure to connect the clamps properly may cause sparking, an explosion or damage to the unit. Always wear eye protection when working with batteries. If battery acid comes into contact with eyes, flush the eyes with water for at least 10 minutes. Seek medical attention immediately. If skin or clothing comes into contact with battery acid, immediately wash the affected area with soap and water. Seek medical attention. Be sure to remove all metal items (watches, necklaces, rings, etc.) before using the Jumpstart System. Always turn the Jumpstart System off when not in use. Store in a cool, dry place. OPERATING USB The Jumpstart is equipped with a 2.1A 10W power port. To operate the USB port, plug adapter in, connect device and push the rocker switch to the USB ON position. USING THE AIR COMPRESSOR The Air Compressor operates from the internal battery of the Jumpstart System. Check battery condition to make sure it is satisfactory before operating compressor. Fully charged condition is best but you may be able to perform a short inflating job in 50% condition. If operating under this condition, check battery during operation and discontinue immediately if battery condition falls below 25%. Recharge unit as soon as possible and before further use. To use the Compressor, remove hose from the storage compartment on the bottom of the unit. With thumb lock lever in the raised position, push connector firmly over valve stem and press down lever to lock it in place. Push the 3 way rocker switch to the compressor O ON position. Digital gas gauge meter+ will automatically illuminate. Monitor the digital gas gauge meter+ while inflating. When desired pressure is reached, turn unit off and disconnect connector by unlocking lever. Disconnect hose and place in storage compartment. Digital gas gauge meter+ will shut off automatically after approximately 30 seconds. Included with your Jumpstart with Compressor are adaptors for inflating athletic balls, and small inflatables. For inflating these objects, select the appropriate adaptor and insert it into the hose connector. Press lever down to lock in place. Inflate object as above. For athletic balls, moisten needle before inserting it into the ball valve. For pneumatic articles, the tapered nozzle should be inserted into the valve and held tightly to insure a good seal.

9 ! WARNING This compressor is capable of inflating objects to high pressures. It will typically take approximately 6-8 minutes to inflate a regular car tire to 30 PSI. Do not over inflate objects beyond their rated capacity. Never leave compressor unattended while in use. This Compressor is designed for periodic use only. Operation over an extended period of time will overheat the unit and damage the motor. Do not operate continuously for over 15 minutes. If you require more than 15 minutes of use, turn off and let it cool for approximately 30 minutes before resuming operation. Do not operate for more than 5 minutes at pressure exceeding 99 PSI, hose failure may result. Pressure gauge on this unit is designed to monitor inflation only and readings may be +/- 2 PSI up to 99 PSI. For readings requiring tighter accuracy, please employ a separate gauge designed for measuring pressure to check reading. OPERATING LED LIGHT The Jumpstart is equipped with an LED work light built in to the front of the unit to provide illumination of the work area for night time repairs or emergency light in case of a power failure. These lights operate using the rocker switch located to the right of the light. Turn off lights to conserve battery power when not required. LED lights are not replaceable, however they will provide many hours of operation under normal working conditions. To turn the lights on, push the switch to the ON position. To turn off, push the switch to the O OFF position.

10 USE AS A 12 VOLT DC PORTABLE POWER SUPPLY The Jumpstart System is equipped with an outlet socket and can be used to operate most 12 volt auto accessories and appliances (11 AMP maximum) equipped with a cigarette lighter plug. Simply lift up cover on socket and plug in appliance. NOTE: socket is live so appliance will be instantaneously powered. Length of time appliance will operate will depend on condition of battery and current draw of appliance. Periodically check battery status during operation and discontinue use immediately if battery condition falls to 25%. Recharge unit as soon as possible and before further use. Power outlet is protected by an internal circuit breaker to prevent damage to unit in case appliance has a short circuit or exceeds 11 AMPS. If circuit breaker is tripped, disconnect appliance and have it checked. Circuit breaker will automatically reset once it cools down (approx minutes). DO NOT PLUG A CIGARETTE LIGHTER INTO THE OUTLET OF THE JUMPSTART. MAINTENANCE INSTRUCTIONS All batteries lose charge with time. AC recharge is recommended after each use or every two months when not in frequent use. Use the AC charger and charge for the recommended time. If the unit gets dirty, gently clean the outer surfaces with a soft cloth moistened with a mild solution of water and detergent. Do not use solvents or other chemical cleaners. Periodically inspect the condition of charging adapters, connectors, and wires. Replace any components that may have become worn or broken. These parts are not serviceable. Do not open or disassemble. Service on Jumpstart is confined to replaceable parts only. All other servicing should be performed by a qualified service personnel only. MOVING AND STORAGE INSTRUCTIONS Always turn the master switch to the O OFF position when not in use. Store in a cool, dry place. Fuse Replacement - 12 volt adapter plug This 12 volt plug is fitted with a 2A fuse in the tip. Should the fuse need replacing, unscrew end cap and replace with a new 2A fuse. BATTERY! CAUTION FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE AND RATING OF FUSE This unit is equipped with a 12 Volt 8 Amp-hour maintenance free, sealed lead acid rechargeable battery, which has a normal life expectancy of up to 1000 charging cycles and will give many years of dependable service if properly cared for following the directions above. In the event that the battery needs replacement in the future, the unit will need to be opened up; this service should be performed by a qualified service professional.

11 Replacement batteries may be purchased from an electrical supply store. Old battery should be disposed of properly and safely. Some states require recycling. Please contact your local solid waste authority for recycling information. WARNING! EXPLOSION HAZARD DO NOT EXPOSE BATTERY TO FIRE OR INTENSE HEAT AS IT MAY EXPLODE. BATTERY CONTAINS ACID: IF CASE SHOULD BECOME CRACKED, DISPOSE OF IMMEDIATELY TAKING ADEQUATE SAFETY PRECAUTIONS TO PREVENT INJURIES OR DAMAGE TO PERSONS OR PROPERTY. CONTAINS NON-SPILLABLE SEALED LEAD ACID BATTERY. BATTERY MUST BE RECYCLED OR DISPOSED OF PROPERLY. LEAD Pb RECYCLE RETURN

12 Limited Warranty Superex warrants to the original purchaser that this product is free from defects in material or workmanship for a period of 1 year from the date of purchase. This warranty does not extend to subsequent purchasers or users. Superex will, during the warranty period, repair or replace the product free of charge. A defective unit may be replaced with a new or reconditioned unit of same or similar design. Superex will, at its option, use new or reconditioned parts in performing warranty repairs. This product is not intended for commercial use and, if so used, will immediately void the warranty. Superex Canada Ltd. assumes no obligation to pay the consumer a cash refund. This Warranty does not cover the failure of, or damage to the product that results from accident, alteration, abuse, misuse, neglect, normal wear and tear (e.g. scratches, chips, dents or discoloration) or failure to follow operating instructions, nor does this Warranty cover damage caused by the use of any attachment not originally equipped with this product. Superex Canada Ltd. Disclaims any liability for any damages resulting from delay or loss of use and service, or repair, or for any incidental or consequential damages arising out of this expressed Warranty, or any implied Warranty, even though it may be caused by negligence or other fault on the part of the Distributor or others. The implied Warranties on this product shall be in effect only for the duration of the expressed Warranties, either expressed or implied. Local laws may vary respecting the limitation on incidental, consequential or other damages, or the length of implied Warranties, so the above limitations may not apply to you. TO OBTAIN WARRANTY SERVICE: In order to qualify for the warranty, a dated proof of purchase must be provided. If your product requires service within 30 days of purchase, please return it along with your original dated sales receipt or other proof of purchase to the original merchant. Otherwise, contact Superex directly at: By phone: By fax: (416) By service@superex.com TO RETURN THE PRODUCT: You must obtain a Return Merchandise Authorization Number (RMA) and a shipping address from Superex prior to returning the product. Please be prepared to provide the Customer Service Agent with your name, address, phone number, model number and a brief description of the problem. Safely package the unit, preferably in its original packing and box, along with a copy of your dated proof of purchase and a short note with your name, address, phone number and a brief description of the problem. Ship the unit PREPAID to the address supplied to you. Do not include any accessories (e.g. cables) with your unit. Make sure to clearly mark the RMA number on the outside of the shipping carton. Superex will examine your unit and at its option, either repair or replace the unit. In either case, the unit will be returned to you freight prepaid within 4 weeks of receipt. Superex Canada Limited, Toronto, M2H 3B8