14.4V Cordless Drill Instruction Manual

Transcription

1 Power Glide Limited Warranty Consumer Power Tools for Home Use to Original Buyer World Factory, Inc. (Seller) warrants to the original Buyer only, that each POWER GLIDE power tool will be free from defects in material and workmanship for a period of one () year from date of purchase. SELLER S SOLE OBLIGATION AND BUYER S EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE THE REPAIR OR REPLACEMENT OF PARTS, WITHOUT CHARGE, WHICH ARE DEFECTIVE IN MATERIAL OR WORKMANSHIP. ANY PARTS AS DETERMINED BY THE SELLER WHICH HAVE BEEN MISUSED; ABUSED OR DAMAGED EITHER DIRECTLY OR INDIRECTLY FROM REPAIRS OR ALTERATIONS ATTEMPTED BY UNAUTHORIZED PERSONS; IMPROPER MAINTENANCE, NEGLECT OR ACCIDENT ARE NOT COVERED BY THIS LIMITED WARRANTY. To make a claim under this Limited Warranty, you must return the complete power tool with proof of purchase, transportation prepaid, to any World Factory, Inc. authorized service center. Call or ; customer.service@worldfactory.com for the location of the nearest authorized power tool service center. Additional Limitations THIS LIMITED WARRANTY DOES NOT APPLY TO COMMERCIAL USER OR ACCESSORY ITEMS SUCH AS CIRCULAR SAW BLADES, DRILL BITS, ROUTER BITS, JIGSAW BLADES, SANDING BELTS OR PADS, GRINDING WHEELS AND OTHER RELATED ITEMS. ALL IMPLIED WARRANTIES SHALL BE LIMITED IN DURATION TO ONE () YEAR FROM DATE OF PURCHASE. IN NO EVENT SHALL SELLER BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED TO LIABILITY FOR LOSS OF PROFITS, ARISING FROM THE SALE OR USE OF THIS PRODUCT. If any provision of this Limited Warranty is for any reason held to be invalid or unenforceable, such provision shall not affect any other provision herein, this Limited Warranty shall be construed as if such invalid and/or unenforceable provision had never been contained herein. This Warranty contains the entire agreement between Seller and Buyer and supersedes any and all prior agreements, arrangements, or understandings between the parties relating to product warranty. Rev V Cordless Drill Instruction Manual Due to ongoing product development the actual product or products may vary from the illustrations or photos shown within this manual. Technical Data Drill 40807rev Model Voltage 4.4V (DC) No Load Speed RPM Chuck Type Jacob's Keyless Weight. lbs. (.5 kgs) Battery Model Voltage 4.4V (DC) Type Ni-Cd Amp Hour.Ah Charger Model Charge Time - 5 Hours Input Voltage 0V ~ 60Hz Output Voltage 7V (DC) Output Current 500mA Made in China 007 World Factory, Inc. Distributed by: World Factory, Inc. Coppell TX 7509 Model No: Read the instructions and precautions before use of this product Please keep Model this instruction No manual for future reference IF YOU HAVE ANY PROBLEMS OR QUESTIONS CONCERNING THIS PRODUCT, DO NOT RETURN IT TO YOUR RETAILER, CONTACT CONSUMER SUPPORT AT OR IF YOU ARE A STORE MANAGER OR EMPLOYEE IN NEED OF ASSISTANCE CALL PLEASE HAVE YOUR STORE NUMBER READY

2 GENERAL SAFETY RULES WARNING: Read all instructions. Failure to follow all instructions listed below may result in electrical shock, fire and/or serious injury. The term power tool in all of the warnings listed below refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool. SAVE THESE INSTRUCTIONS Work Area. Keep your work area clean and well lit. Cluttered and dark areas invite accidents. Do not operate power tools in explosive atmospheres, such as in the presences of flammable liquids, gases, or dust. Power tools create sparks, which may ignite the dust or fumes.. Keep bystanders, children and visitors away while operating a power tool. Distractions can cause you to loose control. Electrical Safety. Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodfied plugs and matching outlets will reduce risk of electrical shock.. Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges, and refrigerators. There is an increased risk of electrical shock if your body is earthed or grounded.. Do not expose power tool to rain or wet conditions. Water entering a power tool will increase the risk of electrical shock. 4. Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entaqngled cords increase the risk of electrical shock. 5. When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electrical shock. Personal Safety. Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury.. Use safety equipment. Always wear eye protection. Safety equipment such dust mask, nonskid safety shoes, hard hat, or hearing protection must be used for appropriate conditions to reduce personal injuries.. Avoid accidental starting. Ensure switch is in the off-position before plugging in. Carrying tools with your finger on the switch or plugging in power tools that have the switch on invites accidents. 4. Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. 5. Do not overreach. Keep proper footing and balance at all times. This enables better control of the tool in unexpected situations. 6. Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewelry or long hair can be caught in moving parts. 7. If devices are provided for connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of these devices can reduce dustrelated hazards. ACCESSORIES CAUTION: Use only Accessories that are recommended by Power Glide for your model. Accessories that may be suitable for one tool may become hazardous when used on another tool. Recommended Accessories:. Drill bits. Screw driving bits. Battery Packs, model no; Battery Charger, model no; Battery Recycling Do not dispose of Ni-Cd batteries in household waste! The battery must be returned, in accordance with legislation on batteries, to the dealer or to the service center. Consult your local telephone listings for a battery recycling center in your area. Ambient temperature maximal 40 C (05 F) Do not dispose of Ni-Cd batteries in household waste Do not throw Ni-Cd batteries into water! Protect Ni-Cd batteries against heat and fire risk of explosion Recycling 4

3 MAINTENANCE (continued) Battery Maintenance WARNING: RISK OF PERSONAL INJURY OR FIRE DAMAGE TO TOOL. Never touch both terminals with metal objects or body parts as a short circuit may result. Do not attempt to destroy or disassemble battery pack or remove any of its components. After removing battery pack, cover the terminals with electrical or heavy-duty adhesive tape. Failure to comply with these warnings could result in fire and serious injury. Your tool is powered by a Nickel-cadmium battery pack. Nickel-cadmium batteries are powerful, rugged and will provide hundreds of charge/discharge cycles if properly maintained and periodically exercised. Exercising is required to recover most of the capacity lost during usage. How to Care for Your Nickel-Cadmium Battery. Never allow a battery to freeze.. Never charge a battery that has been stored at or below 5 o C or above 40 o C. Allow it to sit at room temperature for at least 0 minutes before charging.. Do not charge a battery if it feels warm to the touch. 4. Never charge a battery after a short use. Let it sit until it is needed again. 5. Never charge the battery until the tool in which it is being used cannot produce useful work. 6. Do not leave a battery on the charger after charging time has expired; usually to 5 hours. 7. Your charger will not damage the battery. However, the heat it produces shortens the batter operational life. How to Exercise a Nickel-Cadmium Battery Every two months or after 0 charge/discharge cycles, whichever comes first, fully discharge your battery. Place battery in tool and work with the tool until it nearly stops and no longer produces useful action. Recharge the battery as described in the battery charging section of this manual. Service WARNING: Tools service must be performed only by qualified repair personal. Service or maintenance performed by unqualified personnel could result in a risk of injury. When servicing a tool, use only identical replacement parts. Follow instruction in the maintenance section of this manual. Use of unauthorized parts or failure to follow maintenance instructions may create a risk of electric shock or injury. Contact World Factory, by phone at , or be at customerservice@worldfactory.com, for the location of the nearest authorized power tool service center. Power Tool Use And Care. Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it is designed.. Do not use power tool if switch does not turn it on or off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.. Disconnect the plug from the power source and/or battery pack from the power tool before making any adjustments, changing accessories, or storing the tool. Such preventative safety measures reduce the risk of starting the tool accidentally. 4. Store idle power tools out of reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Tools are dangerous in the hands 5. Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tools operation. If damaged, have the power tool repaired before using. Many accidents are caused by poorly maintained tools. 6. Keep cutting tools sharp and clean. Properly maintained tools with sharp cutting edges are less likely to bind and are easier to control. 7. Use the power tool, accessories and tool bits etc., in accordance with these instructions and in a manner intended for the particular type of power tool, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in hazardous situation. Battery Tool Use and Care. Ensure the switch is in the off position before inserting the battery pack. Inserting the battery pack into power tools that have the switch on invites accidents.. Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery.. Use power toold only with specifically designated battery packs. Use of any other batteries may create a risk of fire. 4. When battery pack is not in use, keep it away from other metal objects like paper clips, coins, keys, nails, screws, or other small objects that can make connection from one terminal to another. Shorting the battery terminals together may cause sparks, burns or a fire. 5. Under abusive conditions, liquid may be ejected from the battery, avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the batery may cause irritation or burns. Service. Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.

4 SPECIFIC SAFETY RULES. Hold power tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its own cord. Contact with a "live"wire will make exposed metal parts of the tool "live" and shock the operator.. Always keep your hands out of the path of the drill. Avoid awkward hand positions where a sudden slip could cause your hand to move into the path of the drill bit.. Do not drill material too small to be securely held. 4. Secure workpiece. Use clamps or a vice to hold the workpiece. It is safer than using your hand and it frees both hands to operate the tool. 5. Make sure there are no nails or foreign objects in the path of the workpiece to be drilled. 6. To avaoid injury from accidental starting, always remove the battery from the tool before installing or removing a drill bit. 7. Do not install or use any drill bit that exceeds 7" (75mm) in length or extends more than 6" (50mm) beyond the chuck jaws. They can bend or break suddenly. 8. Before starting the operation, jog the drill switch to make sure the drill bit does not wobble or vibrate. 9. Do not use fly cutters or multi-part hole cutters, as they can come apart or become unbalanced in use. 0. Make sure the spindle has come to a complete stop before touching the chuck or attempting to change the drill bit.. Always make sure the chuck is tight and the drill bit firmly tightened in the chuck before starting the drill. MAINTENANCE Cleaning WARNING: RISK OF PERSONAL INJURY. Always disconnect tool from power source before making any adjustment, installing or changing accessories.. Clean the tool housing and motor vents after each use.. Keep the grip dry, clean and free from oil and grease.. Store the tool on a safe and dry place, out of reach of children. 4. Do not use cleaning agents or solvents that could attach the plastic parts of the tool. 5. Turn the tool off immediately and do not operate, until repaired, if tool begins to make abnormal noise, vibrations, produces smoke or burning odor. Chuck Removal The drill chuck must be removed in order to use some accessories.. Remove the battery pack from the drill.. Open chuck jaws as far as possible.. (SEE FIGURE 0) Remove the retaining screw () in the bottom of the chuck using a # Phillips screwdriver. Turn screw clockwise to remove it. This screw has a lefthanded thread. Figure 0 Retaining Screw Chuck Jaws 4. (SEE FIGURE ) Insert a hex key () into chuck () and tighten chuck jaws securely. Make sure the chuck jaws are seated on flat surface of the hex key. 5. Tap the hex key sharply with a mallet () in a counter-clockwise direction. This will loosen the chuck on the spindle. Unscrew and remove chuck from the spindle by hand. 6. Reverse steps - 5 to install new chuck. (Maintenance continued on next vpage.) Figure

5 OPERATION (continued) Driving & Removing Screws When driving screws - use suitable bits for the size and type of screw being used. Drill a pilot hole in most application to avoid splitting material. Use lower speeds for better control and to avoid stripping the screw head.. (SEE FIGURE 9) Install the appropriate Figure 9 screwdriver bit or accessory for the job. Make sure the flats of the bit are gripped by the chuck jaws and the bit is firmly locked into the drill chuck.. Set the forward / reverse switch () for the desired rotational direction.. Rotate the clutch adjustment ring () to the appropriate setting based on the Torque Adjustment Chart shown on Page 7. If material is particularly soft or porous, set the clutch at a lower setting to avoid over driving the screw. Always start on the lowest setting. If the correct setting has been chosen, the screw will be turned flush into the material at the same time the clutch begins releasing (clicking noise created as the motor rotation continues but the chuck slows or stops in response to torque). If the screw is driven too far into the workpiece before the clutch releases, set the clutch to a lower setting and do not pull the trigger switch fully back. If the screw is not driven far enough into the workpiece, set the clutch at a higher setting. NOTE: Do not continue to drive the screw once the clutch has released. This will damage the clutch. When removing screws, select a higher setting or set to drill symbol. The proper settings are best determined in practical trials. 4. Pull the On-Off trigger switch () to start the drill. Rotational speed will increase as the trigger is pulled. CAUTION: Drilling with lowest rotation speed for an extended period, increases the danger of overheating the drill's motor. Allow cooling time of approximately 5 minutes between extended drilling periods. 5. Release the On-Off trigger switch when the operation is complete. SAFETY INSTRUCTIONS FOR BATTERY AND CHARGER Before using the charger and battery pack, read the Instruction Manual carefully. WARNING: CHEMICAL HAZARD. Do not open battery pack casing. Protect the battery pack from impacts. If electrolyte leakage occurs from the battery, it is essential to avoid contact with skin. If electrolyte does come into contact with your skin, rinse off with water immediately. In the event of electrolyte contact with your eyes, consult a physician immediately.. Verify the available current corresponds to current required by battery charger.. Verify correct polarity (+/-) before inserting the battery pack into the charger.. Do not use battery charger outdoors. Never let moisture, rain, or splashed water reach the charging location. 4. Do not charge battery pack with the temperature is below 0 o C (50 o F) or above 40 o C (05 o F). Charging battery at extreme temperatures can cause shorter battery life. 5. Damaged battery packs or batteries no longer accepting a charge must be disposed of as hazardous waste. Do not throw the battery pack into the trash, into fire, or into water. See battery Recycling section for disposal information. 6. Do not operate charger with a damaged electrical cable or housing. Charger with damaged electrical cable is non-serviceable and must be replaced with a new one. 7. Use only battery packs and chargers approved by manufacturer for use in tools. Approved battery packs and chargers are listed in the Accessories section of this manual. 8. Always keep the charger free from dust and dirt. 9. Always remove battery pack before working on the tool. 0. Cover the battery pack contacts to avoid short-circuiting.. Avoid the risk of explosion! Do not throw Ni-Cd batteries into water or fire.. NO SMOKING in battery charging or storage areas. Damaged Ni-Cd or Ni-Mh batteres may vent the explosive gas hydrogen that can ignite on exposure to any namked flame or spark.. Store unused battery away from heat sources. 4

6 CALIFORNIA PROPOSITION 65 WARNING: RISK OF CHEMICAL EXPOSURE. Use of this tool can generate dust containing chemicals known to the state of California to cause cancer, birth defects or other reproductive harm. To reduce exposure to these chemicals, always use approved safety equipment, work in a well-ventilated area and wear dusk mask that filters out microscopic particles. The following symbols are used for this tool: Symbol A or Amp V W ~ Hz.../min or RPM Min OPM N o SYMBOLS Name Amperes Volts Watts Alternating Current Direct Current Double Insulated Class II Tool Hertz Revolutions per minute Minutes Oscillations per Minute No Load Speed Safety Alert Basic Operation Drilling Holes. (SEE FIGURE 8) Install the appropriate bit or Figure 8 accessory for the job. Make sure it is firmly locked into the drill chuck.. Set the forward / reverse switch () for the desired rotational direction.. Rotate the clutch adjustment ring () to the drill setting. 4. Hold the drill firmly with both hands whenever possible. Use one hand to grasp the handle and switch and the other to grasp the body of the drill. NOTE: Make sure the hand placed on the body of the drill does not cover the air vents. Covering these air vents will reduce the motor cooling and possibly lead to overheating the motor. 5. While holding the drill firmly, place the point of the drill bit at the point to be drilled. 6. Pull the On-Off trigger switch () to start the drill. Rotational speed will increase as the trigger is pulled. Note: Always use a higher drill speed when drilling small holes. Use a slower drill speed when drilling large holes. CAUTION: Drilling with lowest rotation speed for an extended period, increases the danger of overheating the drill's motor. Allow cooling time of approximately 5 minutes between extended drilling periods. 7. Move the drill bit into the workpiece applying only enough pressure to keep the bit cutting. Do not force the drill bit or apply sideways pressure to elongate the hole. 8. Release the On-Off trigger switch when the operation is complete. Drilling in Different Materials: Wood - Hold the drill firmly and place the point of the bit in the center of the desired hole location. Depress the trigger to start drilling. Metal - Use a punch to mark hole position. Place the point of the bit in the center of punch mark. Depress the trigger to start drilling. Use cutting oil in most metals to improve drilling action and prolong bit life. See cutting oil and/or drill bit manufacturer recommendation for use. Plastic - Use high-speed steel drill bits and refer to wood drilling. NOTE: A jammed bit can often be freed by placing the drill in reverse and slowly backing out of the workpiece. (Operation section continued on next page.) 5 0

7 ASSEMBLY (continued) Installing or Changing Drill and Screwdriver Bits WARNING! PERSONAL INJURY HAZARD. Ensure the drill is turned off and the battery pack removed before changing bits or making any adjustments to the tool.. (SEE FIGURE 7) To insert a drill bit, screwdriver bit or other accessory, grasp the back section of the chuck () and rotate front section () counter clockwise to open drill chuck. Figure 7. Insert the shank into chuck as far as it will go. NOTE: Do not allow chuck jaws to grip bit by fluted or cutting portion.. Firmly rotate the front section clockwise to secure the bit. Ensure bit is firmly seated in the drill chuck before operation. Figure. Grip. Carrying Strap (Lanyard). Battery Pack 4. Trigger 5. Forward / Reverse Switch 6. Keyless Chuck 7. Torque Adjustment Ring GETTING TO KNOW YOUR TOOL Figure OPERATION WARNING: PERSONAL INJURY HAZARD. Always remove the battery pack from the tool before making any adjustment, installing or changing the accessories. Never touch the drill bit or other tool while it is moving. Do not touch the drill bit after operation, it will be very hot. If the drill bit jams in the workpiece or if the drill stalls, stop immediately. Remove the bit from the work piece and correct the reason for stall before continuing. Maximum torque often occurs at the point the bit breaks through the work piece. Grasp the tool firmly and proceed slowly as this occurs. CAUTION: Always use clamps to secure the work piece when drilling. Do not drill material too small to be securely held. Always keep hands out of the path of the drill bit. Avoid awkward hand positions where a sudden slip could cause your hand to move into the path of the drill bit. Make sure there are no nails or foreign objects in the part of the workpiece to be drilled. Do not install or use any drill bit that exceeds 7 (75 mm) in length or extends more than 6 (50 mm) beyond the chuck jaws. They can bend or break suddenly. Before starting the operation, jog the drill switch to make sure the drill bit does not wobble or vibrate. Do not use fly cutters or multiple-part hole cutters, as they can come apart or become unbalanced in use. Always make sure the chuck is tight and drill bit firmly tightened in chuck before starting drill. (Operation section continued on next page.). Drill. Battery Pack. Charger 4. Charger Stand 5. /pcs Accessories Kit 6. Instruction Manusl 7. Plastic Case CONTENTS 9 6

8 Variable Speed On/Off Switch. (SEE FIGURE ) To start drill, pull the trigger switch (). Rotational speed will increase as the trigger is pressed.. To stop drill, release the trigger. FUNCTIONAL DESCRIPTION Forward & Reversing Switch CAUTION: Do not move the forward and reverse switch while drill is in use, damage to tool could result. Allow tool to come to a complete stop before changing direction. Always check tool rotation direction before operation.. (SEE FIGURE ) Use the forward and reverse switch () to select direction. Push button to the left position for clockwise rotation and right position for counter clockwise rotation. Torque Adjustments Ring The tightening power (torque) of your drill/driver is adjustable to various levels of driving power. Generally the larger the screw diameter the higher the torque power setting is required to drive the screw until it is properly seated.. (SEE FIGURE 4) To adjust torque, rotate the clutch adjustment ring () until the desired setting number is aligned with the indicator arrow (). Torque Adjustment Chart Setting Typical Use to : For driving small screws. to 4: For driving screws into soft materials or plastics. 5 to 0: For driving screws into soft woods. to 4: For driving screws into medium/hard woods. 5 to 6: For powerful screw driving. For drilling metal, wood or using spade (Hole) bits. Figure Figure Figure ASSEMBLY WARNING: RISK OF PERSONAL INJURY. Always disconnect the tool from the power outlet before making any adjustment, installing or changing the wheel. Battery Pack Installation & Removal. (SEE FIGURE 5) Insert charged battery pack () into tool handle () and secure with release buttons (). NOTE: There are release buttons on both sides of the battery. The spring must snap into place before the battery is safely secured.. Separate the battery () from the tool handle () by pressing the release buttons () and pulling the battery away from the tool. Figure 5 Charging Battery Pack CAUTION: Do not charge the battery for more than 7 hours. Overcharging may shorten life of the battery pack. Always remove battery pack from charging base when charging is complete. NOTE: The battery pack must be charged before first time use. The battery pack only reaches its full capacity after several charges.. (SEE FIGURE 6) Plug the charger () into a standard 0/0v ~ 60Hz power outlet. Figure 6 4. Plug the DC connector plug () into the charging stand ().. Carefully insert the battery pack (4) into the charger stand. 5 NOTE: The battery pack fits in one direction, do not force the battery pack into the stand. 4. Verify indicator light (5) is lit, if indicator light does not turn on, ensure charger and DC connector plug are securely connected. NOTE: The indicator light will come on and remain on until power is removed from adapter or battery pack is removed from charger stand. If the battery pack reaches a temperature above 40 o C (+05 o F), the battery charger indicator light will turn off for self-protection. The indicator light will turn back on when battery pack temperature cools down. 5. Charge battery pack for -5 hours to reach a full charge. The battery pack and charger unit will warm up during the charging process. This is normal. 6. After battery pack is fully charged, disconnect charger from power outlet. 7. Remove the battery pack from the charger stand. Recharging Battery Charge the battery for -5 hours from a fully discharged condition. Follow steps - 7 for charging battery. Do not repeatedly recharge battery pack after using briefly (5 min. or less). (Assembly section continued on next page.) 7 8