721F. Transmission: 4F/3R proportional w/ Electronic Control Module torque sensing autoshift/manual shift and modulation

Transcription

1 721F WASTE HANDLER Articulated Wheel Loader Tier 4 Interim Certified ENGINE Make Model Type Cylinders Bore/Stroke Case/FPT F4HFE613Y Tier 4 Interim Certified 4-stroke, turbocharged and air-to-air-cooled 6-cylinder in line 4.09 x 5.20 in (104 x 132 mm) Displacement 411 in 3 (6.7 L) Fuel #2 Diesel (#1 & 2 mixture permitted for cold temperature) Does not require ultra-low sulfur fuel B20 biodiesel tolerant Fuel injection Fuel filter Fuel pump Fuel cooler Gradeability Air filter Direct injection electronic Replaceable, full flow spin-on cartridge Bosch CR/CP3 35 fore/aft & side-to-side Dry type element w/ warning restriction indicator Mid-mount cooling module: External independent-mounted coolers Fan: Style 8 blade puller Diameter 32 in (813 mm) Water pump Integral Engine oil: Pump: Deep sump plate cooler w/ pressurized under-piston nozzles Pump operating angles ratings: Side-to-side 35 Fore and aft 35 Oil filtration Replaceable, full flow, spin-on cartridge Engine speeds RPM: Rated speed, full load 2000 Horsepower: Maximum Power Mode: Peak 2000 RPM 195 hp (145 kw) Net 2000 RPM 179 hp (133 kw) Peak 2000 RPM 179 hp (133 kw) Standard Power Mode: Net 2000 RPM 144 hp (107 kw) Peak 1600 RPM 163 hp (121 kw) Economy Power Mode: Net 2000 RPM 121 hp (90 kw) Peak 1400 RPM 138 hp (103 kw) NOTE: Gross horsepower and torque per SAE J1995 Net horsepower and torque per SAE J1349 ENGINE (cont.) Torque peak: Maximum Power Mode: Gross 701 lb ft (950 N 1300 RPM Net 674 lb ft (914 N 1300 RPM Standard Power Mode: Gross 620 lb ft (841 N 1300 RPM Net 594 lb ft (805 N 1300 RPM Economy Power Mode: Gross 589 lb ft (799 N 1200 RPM Net 567 lb ft (768 N 1200 RPM Torque rise: Maximum Power Mode 37% POWERTRAIN Transmission: 4F/3R proportional w/ Electronic Control Module torque sensing autoshift/manual shift and modulation Gears Helical cut Gear ratios Forward/Reverse 1st 3.745/ nd 2.184/ rd 1.072/ th 0.636/ Gear ratios optional 5-speed transmission: Forward/Reverse 1st 3.921/ nd 2.255/ rd 1.466/ th 0.942/ 5th 0.613/ Torque converter: Stall ratio 4-speed 5-speed 2.81:1 2.42:1 Differential optional axles: Limited slip on front and rear axles Rear axle oscillation 24 total Axles Front Rear Differential ratio Planetary ratio Final axle ratio Heavy-duty axles standard: Front axle equipped w/ locking differential Rear axle equipped w/ open differential Planetaries Outboard Service brakes: Hydraulically actuated, maintenance-free, multiple wet disc w/ accumulator to all four wheels Brake surface area per hub 600 in 2 (0.39 m 2 ) Parking brakes: Spring-applied hydraulic release disc on transmission output shaft POWERTRAIN (cont.) Travel speeds 4-speed transmission: Forward Reverse mph (kph) mph (kph) 1st 4.7 (7.6) 5.0 (8.0) 2nd 7.9 (12.8) 8.4 (13.4) 3rd 15.2 (24.5) 15.9 (25.7) 4th 23.5 (37.8) Travel speeds 5-speed transmission w/ lock-up torque converter: Forward Reverse mph (kph) mph (kph) 1st 4.5 (7.2) 4.9 (7.9) 2nd 7.8 (12.6) 8.4 (13.5) 3rd 11.8 (19.0) 19.3 (31.1) 4th 18.3 (29.5) 5th 25.0 (40.0) NOTE: Travel speeds at full engine throttle w/ 20.5 x 25 L3 tires. ELECTRICAL Voltage Alternator Batteries (2) 24 Volts, negative ground 65 amp 700 CCA 12-Volt OPERATOR ENVIRONMENT ROPS/FOPS cab w/ heat; Key start; Articulated power steering w/ tilt column; Fully adjustable, suspension seat; Foot throttle; 1-Lever loader control w/ wrist rest; Cup holder; Coat hook; 1 Interior rearview mirror; 2 in (51 mm) retractable seat belt; Storage tray behind seat; Lunch box compartment; Single brake pedal; F/N/R shuttle switch; Glove box; Pressurized air filtering; Anti-glare window strip; Defroster; Side window, partial/fully open; Dome light; Wipers, rear and intermittent front; Windshield washers, front and rear; Rubber floor mat; Horn. Gauges: Analog: Fuel level; Engine coolant temperature; Transmission oil temperature; Hydraulic oil temperature. LCD screen: Hour meter; Engine speed; Travel speed; Current gear selection; FNR indication; Clock; Trip computer; Fuel consumption; Fuel level percentage; DEF (Diesel Exhaust Fluid) gauge; Oil pressure; Coolant temperature; Engine oil temperature; Transmission oil temperature; Transmission sump oil temperature; Hydraulic oil temperature; Turbocharger air temperature; Differential lock indicator*; Joystick steering indicator*; Automatic transmission indicator; De-clutch indicator; Engine mode indicator; Engine diagnostics; Transmission diagnostics; System voltage; Error reporting. Page 1 of 10

2 OPERATOR ENVIRONMENT (cont.) Warning lights: Low fuel; Turn signals; Four-way flashers; High beam lights; Grid heater*; Brake pressure; Master indicator; Secondary steering*; Parking brake. Audible/Visual alarms: Caution alarm: Parking brake; Coolant temperature; Hydraulic oil temperature; Transmission oil temperature; Air filter; Transmission filter; Hydraulic filter; Alternator; Low fuel. Critical alarm: Engine oil pressure; Brake pressure; Steering pressure w/ secondary steering*; Coolant temperature; Hydraulic oil temperature; Transmission oil temperature. Backup alarm NOTE: *If equipped w/ option. OPERATING WEIGHT Z-Bar Unit equipped w/ ROPS cab w/ heater and A/C, full counterweight, 20.5R25 XHA TL Michelin tires, front and rear fenders, 3.25 yd 3 (2.5 m 3 ) HD Pin On bucket w/ edge, full fuel, 175 lb (79 kg) operator, all optional guarding elements: 32,502 lb ( kg) XR Unit equipped w/ ROPS cab w/ heater and A/C, full counterweight, 20.5R25 XHA TL Michelin tires, front and rear fenders, 3.25 yd 3 (2.5 m 3 ) HD Pin On bucket w/ edge, full fuel, 175 lb (79 kg) operator, all optional guarding elements: 32,983 lb ( kg) HYDRAULICS Pump steering/implement: Closed center pressure/flow compensated Variable displacement maximum flow: 6.59 in 3 (108 cc)/rev ,600 psi ( kpa) Loader control valve: Closed-center, load-sensing, sectional 2-, 3- or 4-spool w/ pilot control for lift, tilt and auxiliary hydraulics, regeneration for bucket dump circuit, electromagnetic detents in float, raise and rollback Loader secondary steering optional: Hydraulic orbital center-pivot articulating w/ on-demand oil flow High pressure standby: Implement 3,625 psi ( kpa) Steering 3,500 psi ( kpa) Filtration: 10 micron, full flow replaceable cartridges on return line furnish only clean oil to all components of the system, condition indicator light for filter SERVICE Capacity Fuel tank 65.0 gal (246.0 L) DEF (Diesel Exhaust Fluid) tank 15.8 gal (59.8 L) Usable capacity 10.9 gal (41.3 L) Hydraulic system: Reservoir 24.0 gal (90.8 L) Total 47.0 gal (177.8 L) Transmission: Service w/ filter 36.0 qt (34.0 L) Front and rear axle: Front axle 37.0 qt (35.0 L) Rear axle 24.3 qt (23.0 L) Front and rear axle optional: Front axle 37.0 qt (35.0 L) Rear axle 37.0 qt (35.0 L) Engine oil w/ filter 16.0 qt (15.1 L) Cooling system (-40) 30.0 qt (28.4 L) OTHER SPECIFICATIONS Lift cylinder: Bore diameter 4.75 in (120.6 mm) Rod diameter 3.00 in (76.2 mm) Stroke in (827.9 mm) Dump cylinder: Bore diameter 5.75 in (146.0 mm) Rod diameter 3.00 in (76.2 mm) Stroke in (629.4 mm) Loader: Z-Bar loader linkage; Single control for lift and tilt; Positive hold float; Automatic return-to-dig; Automatic height control; Automatic return-to-travel; Brake pedal transmission disconnect; Bucket position indicator on bucket. Cycle time: Raise w/ rated bucket load 5.2 sec Dump w/ rated bucket load 1.2 sec Lower empty: Power down 2.5 sec Float down 2.4 sec 721F Waste Handler Page 2 of 10

3 E J K F A H D C G B L Line drawings are for illustrative purpose only and may not be exact representation of unit. DIMENSIONS A. Height to top of ROPS cab in (3385 mm) B. Wheelbase in (3253 mm) C. Ground clearance 14.4 in (365 mm) D. Angle of departure 32 Width: Overall* without bucket in (2653 mm) Centerline tread 79.9 in (2030 mm) Turning radius* outside of tires in (5750 mm) Turning angle: From center 40 Total angle 80 Rear axle oscillation, total 24 NOTE: *Dimensions taken with 20.5R25 Michelin XTLA tires. For transport dimensions, refer to specific bucket width and overall medium length on pages 4 through 8. WEIGHT ADJUSTMENTS Tipping Load Tipping Load Weight Adjustment Adjustment Select Options Adjustment Straight 40 Turn 20.5 x ply L2 tires -556 lb (-252 kg) -436 lb (-198 kg) -385 lb (-175 kg) 20.5 x ply L3 tires -228 lb (-103 kg) -179 lb (-81 kg) -158 lb (-72 kg) 20.5 R25 XTLA TL tires -380 lb (-172 kg) -298 lb (-135 kg) -263 lb (-119 kg) Standard counterweight -527 lb (-240 kg) -1,209 lb (-548 kg) -1,023 lb (-464 kg) ROPS Canopy -295 lb (-134 kg) -339 lb (-154 kg) -314 lb (-142 kg) NOTE: Unit equipped with Z-Bar loader arms, 3.0 yd 3 (2.3 m 3 ) general purpose pin on bucket with bolt-on edge, 20.5R25 XHA Michelin tires, ROPS cab with heater and air conditioner, full counterweight, standard batteries, front and rear fenders, full fuel and 175 lb (79 kg) operator. Adjust select options from rated weight. 721F Waste Handler Page 3 of 10

4 PERFORMANCE DATA 721F Waste Handler Z-Bar* 3.0 yd 3 High Density 3.0 yd 3 High Density 3.25 yd 3 Medium Density Pin On (2.3 m 3 ) Bucket Pin On (2.3 m 3 ) Bucket Pin On (2.5 m 3 ) Bucket with Bolt-on Edge with Teeth Only with Bolt-on Edge SAE bucket capacity struck 2.53 yd 3 (1.94 m 3 ) 2.42 yd 3 (1.85 m 3 ) 2.76 yd 3 (2.11 m 3 ) Heaped 3.01 yd 3 (2.30 m 3 ) 2.79 yd 3 (2.13 m 3 ) 3.25 yd 3 (2.49 m 3 ) Bucket width outside in (2700 mm) in (2732 mm) in (2700 mm) Bucket weight 2,506 lb (1137 kg) 2,605 lb (1182 kg) 2,615 lb (1186 kg) E. Operating height fully raised with spillguard in (5169 mm) in (5169 mm) in (5229 mm) F. Hinge pin height fully raised in (3979 mm) in (3979 mm) in (3979 mm) G. Overall length bucket level on ground in (7596 mm) in (7748 mm) in (7648 mm) H. Dump height fully raised, 45 dump in (2963 mm) in (2864 mm) in (2930 mm) J. Bucket reach fully raised, 45 dump 42.7 in (1086 mm) 47.1 in (1196 mm) 44.3 in (1125 mm) K. Bucket reach 7 ft 0 in (2.13 m) height, 45 dump 64.3 in (1633 mm) 66.9 in (1698 mm) 65.3 in (1658 mm) Operating load ISO 11,686 lb (5301 kg) 11,778 lb (5342 kg) 11,606 lb (5265 kg) Maximum material density SAE 3,525 lb/yd 3 (2091 kg/m 3 ) 3,836 lb/yd 3 (2276 kg/m 3 ) 3,237 lb/yd 3 (1920 kg/m 3 ) Straight 26,696 lb ( kg) 26,919 lb ( kg) 26,530 lb ( kg) 40 turn 23,372 lb ( kg) 23,556 lb ( kg) 23,213 lb ( kg) Full height 16,288 lb (7388 kg) 16,192 lb (7345 kg) 16,180 lb (7339 kg) Maximum reach 22,519 lb ( kg) 22,443 lb ( kg) 22,405 lb ( kg) Ground 29,922 lb ( kg) 30,090 lb ( kg) 29,689 lb ( kg) Breakout force with tilt cylinder 32,907 lb ( kg) 35,598 lb ( kg) 31,382 lb ( kg) Maximum rollback: Ground Carry position Maximum reach Full height L. Dig depth 2.9 in (73 mm) 3.1 in (78 mm) 2.9 in (73 mm) Maximum grading angle with bucket back dragging Loader clearance circle with bucket in ( mm) in ( mm) in ( mm) 721F Waste Handler XR 3.0 yd 3 High Density 3.0 yd 3 High Density 3.25 yd 3 Medium Density Pin On (2.3 m 3 ) Bucket Pin On (2.3 m 3 ) Bucket Pin On (2.5 m 3 ) Bucket with Bolt-on Edge with Teeth Only with Bolt-on Edge E. Operating height fully raised with spillguard in (5564 mm) in (5563 mm) in (5623 mm) F. Hinge pin height fully raised in (4374 mm) in (4374 mm) in (4374 mm) G. Overall length bucket level on ground in (7955 mm) in (8106 mm) in (8006 mm) H. Dump height fully raised, 45 dump in (3358 mm) in (3259 mm) in (3324 mm) J. Bucket reach fully raised, 45 dump 42.8 in (1087 mm) 47.1 in (1197 mm) 44.3 in (1126 mm) K. Bucket reach 7 ft 0 in (2.13 m) height, 45 dump 76.4 in (1942 mm) 79.2 in (2012 mm) 77.5 in (1968 mm) Operating load ISO 9,785 lb (4438 kg) 9,841 lb (4464 kg) 9,709 lb (4404 kg) Maximum material density SAE 2,976 lb/yd 3 (1766 kg/m 3 ) 3,233 lb/yd 3 (1918 kg/m 3 ) 2,731 lb/yd 3 (1620 kg/m 3 ) Straight 22,473 lb ( kg) 22,617 lb ( kg) 22,315 lb ( kg) 40 turn 19,569 lb (8876 kg) 19,683 lb (8928 kg) 19,417 lb (8808 kg) Full height 15,182 lb (6886 kg) 15,085 lb (6842 kg) 15,073 lb (6837 kg) Maximum reach 20,200 lb (9163 kg) 20,122 lb (9127 kg) 20,086 lb (9111 kg) Ground 24,933 lb ( kg) 25,033 lb ( kg) 24,726 lb ( kg) Breakout force with tilt cylinder 32,733 lb ( kg) 35,415 lb ( kg) 31,215 lb ( kg) Loader clearance circle with bucket in ( mm) in ( mm) in ( mm) 721F Waste Handler Page 4 of 10

5 PERFORMANCE DATA 721F Waste Handler Z-Bar* 3.25 yd 3 Medium Density 3.5 yd 3 Low Density 3.5 yd 3 (2.7 m 3 ) Bucket Pin On (2.5 m 3 ) Bucket Pin On (2.7 m 3 ) Bucket with Grapple with with Teeth Only with Bolt-on Edge Bolt-on Edge SAE bucket capacity struck 2.62 yd 3 (2.00 m 3 ) 3.01 yd 3 (2.30 m 3 ) 3.03 yd 3 (2.32 m 3 ) Heaped 3.01 yd 3 (2.30 m 3 ) 3.50 yd 3 (2.68 m 3 ) 3.49 yd 3 (2.67 m 3 ) Bucket width outside in (2732 mm) in (2700 mm) in (2700 mm) Bucket weight 2,700 lb (1225 kg) 2,823 lb (1280 kg) 4,366 lb (1981 kg) E. Operating height fully raised with spillguard in (5228 mm) in (5297 mm) in (5286 mm) F. Hinge pin height fully raised in (3979 mm) in (3979 mm) in (3977 mm) G. Overall length bucket level on ground in (7800 mm) in (7708 mm) in (7710 mm) H. Dump height fully raised, 45 dump in (2831 mm) in (2891 mm) in (2889 mm) J. Bucket reach fully raised, 45 dump 48.6 in (1235 mm) 46.1 in (1171 mm) 46.1 in (1171 mm) K. Bucket reach 7 ft 0 in (2.13 m) height, 45 dump 67.8 in (1721 mm) 66.4 in (1686 mm) 66.3 in (1685 mm) Operating load ISO 11,706 lb (5310 kg) 11,461 lb (5199 kg) 10,527 lb (4775 kg) Maximum material density SAE 3,526 lb/yd 3 (2092 kg/m 3 ) 2,964 lb/yd 3 (1759 kg/m 3 ) 2,702 lb/yd 3 (1603 kg/m 3 ) Straight 26,769 lb ( kg) 26,227 lb ( kg) 24,316 lb ( kg) 40 turn 23,413 lb ( kg) 22,922 lb ( kg) 21,055 lb (9550 kg) Full height 16,097 lb (7302 kg) 15,972 lb (7245 kg) 14,426 lb (6544 kg) Maximum reach 22,343 lb ( kg) 22,189 lb ( kg) 20,615 lb (9351 kg) Ground 29,872 lb ( kg) 29,337 lb ( kg) 27,316 lb ( kg) Breakout force with tilt cylinder 33,827 lb ( kg) 29,732 lb ( kg) 27,976 lb ( kg) Maximum rollback: Ground Carry position Maximum reach Full height L. Dig depth 3.1 in (78 mm) 2.9 in (74 mm) 3.0 in (76 mm) Maximum grading angle with bucket back dragging Loader clearance circle with bucket in ( mm) in ( mm) in ( mm) 721F Waste Handler XR 3.25 yd 3 Medium Density 3.5 yd 3 Low Density 3.5 yd 3 (2.7 m 3 ) Bucket Pin On (2.5 m 3 ) Bucket Pin On (2.7 m 3 ) Bucket with Grapple with with Teeth Only with Bolt-on Edge Bolt-on Edge E. Operating height fully raised with spillguard in (5623 mm) in (5692 mm) in (5680 mm) F. Hinge pin height fully raised in (4374 mm) in (4374 mm) in (4372 mm) G. Overall length bucket level on ground in (8157 mm) in (8066 mm) in (8068 mm) H. Dump height fully raised, 45 dump in (3226 mm) in (3286 mm) in (3284 mm) J. Bucket reach fully raised, 45 dump 48.7 in (1236 mm) 46.1 in (1172 mm) 46.1 in (1172 mm) K. Bucket reach 7 ft 0 in (2.13 m) height, 45 dump 80.2 in (2037 mm) 78.7 in (1998 mm) 78.6 in (1998 mm) Operating load ISO 9,773 lb (4433 kg) 9,572 lb (4342 kg) 8,671 lb (3933 kg) Maximum material density SAE 2,969 lb/yd 3 (1762 kg/m 3 ) 2,497 lb/yd 3 (1482 kg/m 3 ) 2,243 lb/yd 3 (1331 kg/m 3 ) Straight 22,474 lb ( kg) 22,031 lb (9993 kg) 20,194 lb (9160 kg) 40 turn 19,546 lb (8866 kg) 19,143 lb (8683 kg) 17,341 lb (7866 kg) Full height 14,990 lb (6799 kg) 14,865 lb (6743 kg) 13,320 lb (6042 kg) Maximum reach 20,022 lb (9082 kg) 19,871 lb (9013 kg) 18,299 lb (8300 kg) Ground 24,839 lb ( kg) 24,405 lb ( kg) 22,477 lb ( kg) Breakout force with tilt cylinder 33,653 lb ( kg) 29,574 lb ( kg) 27,819 lb ( kg) Loader clearance circle with bucket in ( mm) in ( mm) in ( mm) 721F Waste Handler Page 5 of 10

6 PERFORMANCE DATA 721F Waste Handler Z-Bar* 5.5 yd 3 Low Density 3.0 yd 3 General Purpose 3.0 yd 3 General Purpose Pin On (4.2 m 3 ) Bucket (2.3 m 3 ) Bucket on CNH Z-Bar (2.3 m 3 ) Bucket on CNH Z-Bar with Bolt-on Edge Coupler with Bolt-on Edge Coupler with Teeth Only SAE bucket capacity struck 5.49 yd 3 (4.20 m 3 ) 2.51 yd 3 (1.92 m 3 ) 2.42 yd 3 (1.85 m 3 ) Heaped 5.49 yd 3 (4.20 m 3 ) 2.94 yd 3 (2.25 m 3 ) 2.79 yd 3 (2.13 m 3 ) Bucket width outside in (2700 mm) in (2700 mm) in (2732 mm) Bucket weight 3,025 lb (1372 kg) 3,722 lb (1688 kg) 3,559 lb (1614 kg) E. Operating height fully raised with spillguard in (5669 mm) in (5359 mm) in (5360 mm) F. Hinge pin height fully raised in (3979 mm) in (3978 mm) in (3978 mm) G. Overall length bucket level on ground in (8119 mm) in (7868 mm) in (8020 mm) H. Dump height fully raised, 45 dump in (2617 mm) in (2787 mm) in (2689 mm) J. Bucket reach fully raised, 45 dump 56.7 in (1441 mm) 50.9 in (1293 mm) 55.2 in (1403 mm) K. Bucket reach 7 ft 0 in (2.13 m) height, 45 dump 71.3 in (1811 mm) 69.2 in (1757 mm) 71.4 in (1814 mm) Operating load ISO 10,753 lb (4878 kg) 10,168 lb (4620 kg) 10,379 lb (4708 kg) Maximum material density SAE 1,768 lb/yd 3 (1049 kg/m 3 ) 3,132 lb/yd 3 (1858 kg/m 3 ) 3,373 lb/yd 3 (2001 kg/m 3 ) Straight 24,651 lb ( kg) 23,444 lb ( kg) 23,860 lb ( kg) 40 turn 21,507 lb (9755 kg) 20,371 lb (9240 kg) 20,758 lb (9416 kg) Full height 15,759 lb (7148 kg) 15,005 lb (6806 kg) 15,173 lb (6882 kg) Maximum reach 21,879 lb (9924 kg) 21,060 lb (9552 kg) 21,248 lb (9638 kg) Ground 27,958 lb ( kg) 26,962 lb ( kg) 27,342 lb ( kg) Breakout force with tilt cylinder 22,294 lb ( kg) 26,375 lb ( kg) 28,237 lb ( kg) Maximum rollback: Ground Carry position Maximum reach Full height L. Dig depth 4.3 in (110 mm) 2.9 in (75 mm) 3.1 in (80 mm) Maximum grading angle with bucket back dragging Loader clearance circle with bucket in ( mm) in ( mm) in ( mm) 721F Waste Handler XR 5.5 yd 3 Low Density 3.0 yd 3 General Purpose 3.0 yd 3 General Purpose Pin On (4.2 m 3 ) Bucket (2.3 m 3 ) Bucket on Z-Bar (2.3 m 3 ) Bucket on Z-Bar with Bolt-on Edge Coupler with Bolt-on Edge Coupler with Teeth Only E. Operating height fully raised with spillguard in (6064 mm) in (5754 mm) in (5754 mm) F. Hinge pin height fully raised in (4373 mm) in (4372 mm) in (4373 mm) G. Overall length bucket level on ground in (8473 mm) in (8226 mm) in (8377 mm) H. Dump height fully raised, 45 dump in (3012 mm) in (3182 mm) in (3083 mm) J. Bucket reach fully raised, 45 dump 56.8 in (1442 mm) 50.9 in (1294 mm) 55.3 in (1404 mm) K. Bucket reach 7 ft 0 in (2.13 m) height, 45 dump 84.2 in (2140 mm) 81.7 in (2075 mm) 84.2 in (2138 mm) Operating load ISO 9,002 lb (4083 kg) 8,495 lb (3853 kg) 8,662 lb (3929 kg) Maximum material density SAE 1,492 lb/yd 3 (885 kg/m 3 ) 2,631 lb/yd 3 (1561 kg/m 3 ) 2,836 lb/yd 3 (1683 kg/m 3 ) Straight 20,764 lb (9419 kg) 19,695 lb (8933 kg) 20,051 lb (9095 kg) 40 turn 18,004 lb (8167 kg) 16,991 lb (7707 kg) 17,324 lb (7858 kg) Full height 14,654 lb (6647 kg) 13,903 lb (6306 kg) 14,071 lb (6383 kg) Maximum reach 19,570 lb (8877 kg) 18,758 lb (8508 kg) 18,944 lb (8593 kg) Ground 23,269 lb ( kg) 22,412 lb ( kg) 22,734 lb ( kg) Breakout force with tilt cylinder 22,199 lb ( kg) 26,226 lb ( kg) 28,083 lb ( kg) Loader clearance circle with bucket in ( mm) in ( mm) in ( mm) 721F Waste Handler Page 6 of 10

7 PERFORMANCE DATA 721F Waste Handler Z-Bar* 2.6 yd 3 (1.9 m 3 ) 4-in-1 Bucket on CNH Z-Bar coupler SAE bucket capacity struck 2.24 yd 3 (1.71 m 3 ) Heaped 2.59 yd 3 (1.98 m 3 ) Bucket width outside Bucket weight in (2700 mm) 5,000 lb (2268 kg) E. Operating height fully raised with spillguard in (5371 mm) F. Hinge pin height fully raised in (3976 mm) G. Overall length bucket level on ground in (7684 mm) Dump angle fully raised 55 H. Dump height fully raised, 45 dump in (2905 mm) J. Bucket reach fully raised, 45 dump 45.3 in (1150 mm) K. Bucket reach 7 ft 0 in (2.13 m) height, 45 dump 65.8 in (1671 mm) Operating load ISO 10,027 lb (4548 kg) Maximum material density SAE 3,477 lb/yd 3 (2063 kg/m 3 ) Straight 23,223 lb ( kg) 40 turn 20,053 lb (9096 kg) Full height Maximum reach Ground Breakout force with tilt cylinder 13,751 lb (6237 kg) 19,885 lb (9020 kg) 26,464 lb ( kg) 30,119 lb ( kg) Maximum rollback: Ground 39 Carry position Maximum reach Full height 57 L. Dig depth 3.0 in (77 mm) Maximum grading angle with bucket back dragging 59 Loader clearance circle with bucket in ( mm) 721F Waste Handler XR 2.6 yd 3 General Purpose (1.9 m 3 ) 4-in-1 Bucket on Z-Bar coupler E. Operating height fully raised with spillguard in (5765 mm) F. Hinge pin height fully raised in (4371 mm) G. Overall length bucket level on ground in (8042 mm) Dump angle fully raised 55 H. Dump height fully raised, 45 dump in (3299 mm) J. Bucket reach fully raised, 45 dump 45.3 in (1151 mm) K. Bucket reach 7 ft 0 in (2.13 m) height, 45 dump 78.1 in (1983 mm) Operating load ISO 8,236 lb (3736 kg) Maximum material density SAE 2,876 lb/yd 3 (1707 kg/m 3 ) Straight 19,251 lb (8732 kg) 40 turn 16,471 lb (7471 kg) Full height Maximum reach Ground Breakout force with tilt cylinder Loader clearance circle with bucket 12,647 lb (5737 kg) 17,576 lb (7972 kg) 21,739 lb (9861 kg) 29,950 lb ( kg) in ( mm) NOTE: *Z-Bar performance data shown with full counterweight. Performance data unit equipped with 20.5R25 Michelin XHA TL tires, ROPS cab with heater and A/C, full counterweight, standard batteries, front and rear fenders, full fuel and 175 lb (75 kg) operator. Specifications per SAE J732, J1234, J695, J742 and J F Waste Handler Page 7 of 10

8 60 INCH FORKS 721F Waste Handler Z-Bar Lift Arm: Forks on CNH Z-Bar Coupler Dimensional Fork length Vertical front surface of tine to fork tip Fork load center Vertical front surface of tine to load CG Fork width (maximum) Outside to outside of tine Fork full height Ground to top of tine Fork full height Vertical front surface of tine to front of tire Fork maximum reach Ground to top of tine Fork reach (maximum) Vertical front surface of tine to front of tire Fork ground Vertical front surface of tine to front of tire 60.0 in (1524 mm) 30.0 in (762 mm) 60.0 in (1524 mm) in (3692 mm) 36.8 in (934 mm) 69.2 in (1758 mm) 67.2 in (1708 mm) 42.8 in (1088 mm) Operational Fork attachment weight includes coupler Operating load per EN 474-3: Rough terrain Firm and level ground Tipping load straight ISO Tipping 40 turn ISO Operating weight Overall length Forks level on ground 2,664 lb (1208 kg) 8,356 lb (3790 kg) 11,141 lb (5054 kg) 16,336 lb (7410 kg) 13,926 lb (6317 kg) 31,558 lb ( kg) in (8495 mm) XR Lift Arm: Forks on CNH Z-Bar Coupler Dimensional Fork length Vertical front surface of tine to fork tip Fork load center Vertical front surface of tine to load CG Fork width (maximum) Outside to outside of tine Fork full height Ground to top of tine Fork full height Vertical front surface of tine to front of tire Fork maximum reach Ground to top of tine Fork reach (maximum) Vertical front surface of tine to front of tire Fork ground Vertical front surface of tine to front of tire 60.0 in (1524 mm) 30.0 in (762 mm) 60.0 in (1524 mm) in (4086 mm) 36.8 in (935 mm) 69.2 in (1756 mm) 78.5 in (1995 mm) 56.9 in (1446 mm) Operational Fork attachment weight includes coupler Operating load per EN 474-3: Rough terrain Firm and level ground Tipping load straight ISO Tipping 40 turn ISO Operating weight Overall length Forks level on ground 2,664 lb (1208 kg) 7,356 lb (3336 kg) 9,807 lb (4449 kg) 14,465 lb (6561 kg) 12,259 lb (5561 kg) 32,039 lb ( kg) in (8853 mm) 721F Waste Handler Page 8 of 10

9 STANDARD EQUIPMENT OPERATOR ENVIRONMENT See page 1 ENGINE Case/FPT F4HFE613Y Tier 4 Interim Certified Selectable work modes: Maximum Power Standard Power Economy Power Auto Power Turbocharger Charge air cooling Automatic fan belt tensioner Integral engine oil cooling Fuel filter with water trap Dual-element dry-type air cleaner Hydraulic-driven cooling fan 65 amp alternator (2) 700 CCA 12-volt batteries Liquid-cooled radiator Mid-mounted cooling module Common rail electronic fuel injection GUARDING Specialized guarding elements include: Windscreen guard Articulation guards Front cover guard Bottom guards Skid plate guard optional Lift cylinder guard Ejector guards Front light guards Metal wrapped hoses Fuel tank guard Transmission guard POWERTRAIN 4-wheel drive 4F/3R Selectable autoshift/manual shift transmission Electronic Control Module programmable, computer controlled proportional shifting with programmable gear selection Onboard diagnostics Single lever electronic shift control F/N/R switch in loader control handle Downshift button Torque converter Heavy-duty axles: with auto-locking front differential, rear conventional differential and with bronze sintered brake pads Outboard planetary axles Transmission oil cooler Brake pedal transmission disconnect Hydraulic wet disc brakes Spring-applied hydraulic release parking brake Limp-Home Mode Greasable rear axle trunnion 3-piece rims HYDRAULICS 2-spool loader control valve with single lever joystick control Low-effort steering Hydraulic driven fan 8 Diagnostic quick couplers Split flange hydraulic connections 1 inch or greater LOADER See page 2 ELECTRICAL Alternator and voltage regulator Electrical disconnect (2) 700 CCA 12-volt batteries Electric starter Lights: Front and rear halogen flood lights Tail lights and stop lights combined 2 Front driving headlights high/low beam 2 Front flood 2 LED stop/tail lights 2 Rear flood Front and rear turn signal/flash Key start/stop switch Telematics plug port Backup alarm Centrally located fuse box with all electrical circuits protected TELEMATICS Three (3) year SiteWatch Advanced subscription with remote monitoring and one user s licence OTHER Electric raise-up hood Front and rear fenders, partial coverage Standard counterweight Drawbar hitch Articulation locking bar Lift arm locking bar Lift and tie-down points front/rear Remote drain points Grouped remote-mounted ecology drains: Engine oil Engine coolant Hydraulic oil OPTIONAL EQUIPMENT OPERATOR ENVIRONMENT Heated cloth-covered air suspension seat Vinyl-covered mechanical suspension seat 3 in (76 mm) retractable seat belt Sound Shield noise suppression package Cab air-conditioning with heater Radio Radio-ready 12- or 24-volt with auxiliary power 12-volt Cab convenience package RH steps and platform Rotating beacon Second brake pedal Open ROPS Joystick steering External rearview mirrors External rearview mirrors, heated Rear view camera with accessory mount In-cab accessory mount Extra front-facing work lights HYDRAULICS Auxiliary hydraulics Ride Control Secondary steering 3-spool loader valve with joystick plus lever, or 2-lever loader control plus auxiliary lever Variable speed hydraulic reversing fan Hydraulic cooler POWERTRAIN 5F/3R Autoshift/manual shift transmission, lockup torque converter, PowerInch de-clutch Commodity King package with heavy debris cooling system Limited-slip differentials Cold weather package: Heavy-duty (2) 950 CCA 12V batteries Grid heater Fuel heater Hydraulic oil cooler bypass Low temperature hydraulic oil Fast-warm hydraulic valve Full-view or ejector type pre-cleaner Remote jump start receptacle TIRES PR L2 bias dirt/traction PR L2 bias dirt/traction PR L3 bias rock PR L3 bias rock 20.5 R25 L2 radial dirt/traction 20.5 R25 L3 radial rock 20.5 R25 radial Michelin SnoPlus 20.5 R25 radial Bridgestone Snow Wedge SolidFlex HD solid tires on adapter rims Spare wheels and tires Axle oscillation stops Wheel chocks LOADER XR extended reach version Attachment auxiliary hydraulics Coupler systems JRB or ACS compatible Buckets see pages 4 through clamp buckets Forks see page 8 Material handling arm Broom ADVANCED ENGINE AIR FILTRATION Slanted cooling module cover Auto reversing fan Sy-Clone ejective air cleaner Increased cooling fin spacing Added cooling module sealing OTHER Full coverage fenders Right and left side steps Belly pan Side guards for rear frame Tool box ground level access Full counterweight Z-Bar Extra counterweight included with XR Fire extinguisher License plate bracket 12.4 mph (20 kph) maximum speed control Special paint 721F Waste Handler Page 9 of 10

10 NOTE: All specifications are stated in accordance with SAE Standards or Recommended Practices, where applicable. NOTE: All engines meet current EPA emissions requirements. IMPORTANT: Case Construction Equipment Inc. reserves the right to change these specifications without notice and without incurring any obligation relating to such change. Case Construction Equipment Inc. does not warrant the safety or reliability of attachments from other manufacturers. Case is a registered trademark of CNH America LLC. Any trademarks referred to herein, in association with goods and/or services of companies other than CNH America LLC, are the property of those respective companies. Form No. CCE FWH Printed in U.S.A CNH America LLC 721F Waste Handler Page 10 of 10 All Rights Reserved All Case construction equipment is biodiesel ready.