TYPE: TYPE CATALOG# CATALOG#: 5 11 / 16 15W

Transcription

1 : DL360-6" ROUND CEILING DOWNLIGHT (IP65) - AMER SURFACE CEILING MOUNT 4 3 / / 16 Application:This Turtle Safe covered ceiling mount down light can be used in both interior and outdoor settings. Typical locations are in commercial and retail spaces that require lighting from above. Dark Sky compliant. Housing: Constructed from a round one piece high grade aluminum extrusion, die cast aluminum top plate, and faceplate with a powder coat finish. Includes CO, reflector, driver and and a mounting plate. Top plate is secured to housing by threads. Mounting plate is secured to top plate with two (2) flat head phillips stainless steel screws and installs onto an 4" octagonal electrical junction box. Mounting: Fixture includes a mounting bracket for installation directly to a 4" octagonal electrical junction-box. Faceplate: Round one piece extruded aluminum with powder coat finish, clear tempered glass lens, and silicone o-ring. Faceplate is secured to the housing by threads. Reflector Construction: One piece, heavy-gauge aluminum reflector prevents ugly dents during shipping and installation. Deeply mounted singular provides 50 degree visual Dimming: (-DUN) option is a universal dimming system that works with most 3-Wire ELV, 2- Wire Incandescent and 5-Wire 0-10V fluorescent dimmers. Finish: A 7-stage electrostatic, polymer process provides a finish resistance to corrosion and UV-degradation Available in lack, White, Silver* and ronze*. eam Spread: Available in Wide Flood, 2 Pencil eam, Narrow Spot, Spot and Flood. : Energy efficient Chip-On-oard (CO) Singular Light Source provides for smooth uniform light output, eliminating the multiple shadow effect seen by multiple Source products. inned with 4-step MacAdam ellipses as recommended by ANSI Standard. Available in 4000K, 2700K*, 3000K, 3500K*, 5000K*, 5600K* and 590nm AMER*. Energy efficient, low glare Chip-On-oard light engine eam spreads include NS, SP, FL, WFL and 2 Pencil eam Singular CO Light Source Electrical: AC 50/60Hz Electronic Direct Current Class 2 driver integrally mounted. Power Factor > Accessible from above or below ceiling. For cold weather applications (-22 C and above) use -DUN driver option Emergency Options: Emergency attery ack-up available, remotely mounted adjacent to housing by installer. When AC power fails,the device immediately switches to the emergency mode, operating the s for a minimum of 90 minutes. Remote test switch, Caution: LITON recommends use of surge protectors on the power entering Housings. Note: Dark Sky compliant. Listing: ETL / cetl Listed. Suitable for wet location. Assembled in USA. (IP65). FEATURE: ORDERING EXAMPLE : DL TAM-EMAC DL360 DL360 WS Z :lack :White :ronze* EAM SPREAD :Wide Flood -02 :2 Pencil eam -10 :Narrow Spot -20 :Spot -45 :Flood :Non-Dimming (120V)-TAM-LVR:590nm AMER* -EMAC :Emergency ack Up UE-DUN :UniDim (120V/277V) LIGHTING GROU P

2 : DLQ360-6" SQUARE CEILING DOWNLIGHT (IP65) - Amber (Turtle Safe) SURFACE CEILING MOUNT 4 3 / / 16 S PECIFICATIONN Application A pplication:this: Turtle Safe covered ceiling mount down light can be used in both interior and outdoor settings. Typical locations are in commercial and retail spaces that require lighting from above. Dark Sky compliant. Housing ousing: : Constructed from a square one piece high grade aluminum extrusion, die cast aluminum top plate, and faceplate with a powder coat finish. Includes CO, reflector, driver and a mounting plate. Top plate is secured to housing by four (4) tamper resistant, stainless steel screws. Mounting plate is secured to top plate with four (4) flat head phillips stainless steel screws and installs onto an 4" octagonal electrical junction box. Mounting ounting: : Fixture includes a mounting bracket for installation directly to (or over) a 4" octagonal electrical junction-box. Faceplate F aceplate: : Square one piece die cast aluminum with powder coat finish, clear tempered glass lens, and silicone o-ring. Faceplate is secured to the housing by four (4) tamper resistant, stainless steel screws. Reflector Construction: One piece, heavy-gauge aluminum reflector prevents ugly dents during shipping and installation. Deeply mounted singular provides 50 degree visual Dimming: (-DUN) option is a universal dimming system that Wire Incandescent and 5-Wire 0-10V fluorescent dimmers. works with most 3-Wire ELV, 2- Finish: F A 7-stage electrostatic, polymer process provides a finish resistance to corrosion and UV-degradation Available in lack, White, Silver* and ronze*. eam Spread: Available in Wide Flood, 2 Pencil eam, Narrow Spot, Spot and Flood. L ED: Energy efficient Chip-On-oard (CO) Singular Light Source provides for smooth uniform light output, eliminating the multiple shadow effect seen by multiple Source products. inned with 4-step MacAdam ellipses as recommended by ANSI Standard. Available in 4000K, 2700K*, 3000K, 3500K*, 5000K*, 5600K* and 590nm AMER*. enefit: t Daylight sensor available Energy efficient, low glare Chip-On-oard light engine eam spreads include NS, SP, FL, WFL and 2 Pencil eam Singular CO Light Source E lectrical: : AC 50/60Hz Electronic Direct Current Class 2 driver integrally mounted. Power Factor > Accessible from above or below ceiling. For cold weather applications (-22 C and above) use -DUN driver option. Emergency Options: Emergency attery ack-up available, remotely mounted adjacent to housing by installer. When AC power fails,the device immediately switches to the emergency mode, operating the s for a minimum of 90 minutes. Remote test switch, Caution aution: : LITON recommends use of surge protectors on the power entering Housings. Warranty arranty: : Covered by a 5 Year Warranty to be free of defects in materials and Note ote: : Dark Sky compliant. Listing L isting: : ETL E / cetll Listed. Suitable for wet location. Assembled in USA. (IP65). F EATURE: : ORDERING EXAMPLE : DLQ360S-02-TAM-EMAC DLQ360 DLQ360 F :lack W :White Z :ronze* S CO :Copper Penny* EAM SPREAD lankk :Wide Flood L lan lankk :Non-Dimming (120V) -TAM-LVR:590nm AMER* -EMA - EMAC :Emergency UE-DU E-DUN :UniDim (120V/277V) -SD - SDLL -LVR :Daylight Sensor* :Hex-Cell Louver* L I G H TING G R O U P

3 : WD1360-6" ROUND 1-DIRECTION WALL MOUNT (IP65) - AMER SURFACE 1-DIRECTION WALL MOUNT 22W Application: This Turtle Safe directional Wall luminaire can be used in both interior and outdoor settings and can be pointed up or down. Typical locations are in commercial and retail spaces that contain walls and/or columns that require directional lighting. Housing: Constructed from a round one piece high grade aluminum extrusion with a rectangular extrusion arm, end cap, faceplate and a mounting plate with a powder coat finish. Includes CO, reflector and driver. Mounting plate is secured to arm with four (4) flat head phillips stainless steel screws. Mounting plate installs onto an electrical junction box. Consult factory for junction box mounting sizes. Mounting: Fixture includes a mounting bracket for installation directly to a 4" octagonal electrical junction-box. Faceplate: Round one piece extruded aluminum with powder coat finish, clear tempered glass lens, and silicone o-ring. Faceplate is secured to the housing by threads. Reflector Construction: One piece, heavy-gauge aluminum reflector prevents ugly dents during shipping and installation. Deeply mounted singular provides 50 degree visual Dimming: (-DUN) option is a universal dimming system that works with most 3-Wire ELV, 2- Wire Incandescent and 5-Wire 0-10V fluorescent dimmers. Electrical: AC 50/60Hz Electronic Direct Current Class 2 driver integrally mounted. Power Factor > Accessible from above or below ceiling. For cold weather applications (-22 C and above) use -DUN driver option. Emergency Options: Emergency attery ack-up available, remotely mounted adjacent to housing by installer. When AC power fails,the device immediately switches to the emergency mode, operating the s for a minimum of 90 minutes. Remote test switch, Caution: LITON recommends use of surge protectors on the power entering Housings. Note: Dark Sky compliant when fixture is pointing downward. Listing: ETL / cetl Listed. Suitable for wet location. Assembled in USA. (IP65). Finish: A 7-stage electrostatic, polymer process provides a finish resistance to corrosion and UV-degradation Available in lack, White, Silver* and ronze*. eam Spread: Available in Wide Flood, 2 Pencil eam, Narrow Spot, Spot and Flood. : Energy efficient Chip-On-oard (CO) Singular Light Source provides for smooth uniform light output, eliminating the multiple shadow effect seen by multiple Source products. inned with 4-step MacAdam ellipses as recommended by ANSI Standard. Available in 4000K, 2700K*, 3000K, 3500K*, 5000K*, 5600K* and 590nm AMER*. Daylight Sensor available Uniform, low glare illumination Durable, corrosion resistant finish Singular CO Light Source FEATURE: ORDERING EXAMPLE : WD TAM-EMAC WD1360 WD1360 WS Z :lack :White :ronze* EAM SPREAD :Wide Flood -10 :Narrow Spot -20 :Spot -45 :Flood :Non-Dimming (120V)-TAM-LVR:590nm AMER -EMAC :Emergency UE-DUN :UniDim (120V/277V) -SDL :Daylight Sensor* LIGHTING GROU P

4 : WD1Q360-6" SQUARE 1-DIRECTION WALL MOUNT (IP65) - SURFACE 1-DIRECTION WALL MOUNT AMER Application: This Turtle Safe directional Wall luminaire can be used in both interior and outdoor settings and can be pointed up or down. Typical locations are in commercial and retail spaces that contain walls and/or columns that require directional lighting. Housing: Constructed from a square one piece high grade aluminum extrusion with a rectangular extrusion arm, end cap, faceplate and a mounting plate with a powder coat finish. Includes CO, reflector and driver. Mounting plate is secured to arm with four (4) flat head phillips stainless steel screws. Mounting plate installs onto an electrical junction box. Consult factory for junction box mounting sizes. Mounting: Fixture includes a mounting bracket for installation directly to a 4" octagonal electrical junction-box. Faceplate: Square one piece die cast aluminum with powder coat finish, clear tempered glass lens, and silicone o-ring. Faceplate is secured to the housing by four (4) tamper resistant, stainless steel screws. Reflector Construction: One piece, heavy-gauge aluminum reflector prevents ugly dents during shipping and installation. Deeply mounted singular provides 50 degree visual Dimming: (-DUN) option is a universal dimming system that works with most 3-Wire ELV, 2- Wire Incandescent and 5-Wire 0-10V fluorescent dimmers. Electrical: AC 50/60Hz Electronic Direct Current Class 2 driver integrally mounted. Power Factor > Accessible from above or below ceiling. For cold weather applications (-22 C and above) use -DUN driver option. Emergency Options: Emergency attery ack-up available, remotely mounted adjacent to housing by installer. When AC power fails,the device immediately switches to the emergency mode, operating the s for a minimum of 90 minutes. Remote test switch, Caution: LITON recommends use of surge protectors on the power entering Housings. Note: Dark Sky compliant when fixture is pointing downward. Listing: ETL / cetl Listed. Suitable for wet location. Assembled in USA. (IP65). Finish: A 7-stage electrostatic, polymer process provides a finish resistance to corrosion and UV-degradation Available in lack, White, Silver* and ronze*. eam Spread: Available in Wide Flood, 2 Pencil eam, Narrow Spot, Spot and Flood. : Energy efficient Chip-On-oard (CO) Singular Light Source provides for smooth uniform light output, eliminating the multiple shadow effect seen by multiple Source products. inned with 4-step MacAdam ellipses as recommended by ANSI Standard. Available in 4000K, 2700K*, 3000K, 3500K*, 5000K*, 5600K* and 590nm AMER*. Daylight Sensor available Uniform, low glare illumination Durable, corrosion resistant finish Singular CO Light Source FEATURE: ORDERING EXAMPLE : WD1Q T27-EMAC WD1Q360 WD1Q360 WZ Z S :lack :White :ronze* EAM SPREAD :Wide Flood -10 :Narrow Spot -20 :Spot -45 :Flood :Non-Dimming (120V)-TAM-LVR:590nm AMER -EMAC :Emergency UE-DUN :UniDim (120V/277V) -SDL :Daylight Sensor* LIGHTING GROU P

5 : 6" IC Housing w/ 6" Amber Downlight 6" TURTLE SAFE DOWNLIGHT 7 1/2" 7 1/2" 6" 10 1/2" Ceiling cut-out: 6 1/2" Application: Recessed downlight housing and trim designed for interior and covered exterior locations visible from the seaward and the shore perpendicular sides of a building and the landward side if visible from the beach within a designated sea turtle nesting area. Mounting: Housing suitable for new construction installations only, supplied with (2) 24" adjustable hanger bars with 90 degrees repositioning ability. Hanger bars equipped with nail-less install 3/4" serrated barbed studs and with captive nails, for faster and easier secure mounting in wood joists. Set-screws lock into position and prevent shifting after installation. Earthquake structural cable compatible for drop panel ceiling or any other mounting that requires direct support from structural ceilings. Power Connection: heat sinked lamp module is replaceable via onboard quick exclusionary disconnect terminal. No tools required. Meets CA Title 24 Requirements and other standards restricting the use of Medium ase or i-pin Sockets. Driver: Electronic Direct Current U.L. Listed driver mounted away from Array for cool operation and end-of-life modularity. Comes standard with 120VAC input and available with optional 120V/277V universal voltage input. Dimming: Dimming option smoothly dims down as low as 10% of initial light output with flicker-free operation. Incandescent dimming option (-DIN) works with standard Incandescent dimmers. Factory qualified for use with LUTRON rand Dimmers: S600PR, DVSCCL-153P & DV600PR as well at Leviton# IP W. Also works with standard Electronic Low Voltage Dimmers. Factory qualified for use with LUTRON rand Dimmers: SELV-300P, DVELV-300P,NELV-450 along with 3-Way versions. (-DLV) Dimming Option also compatible with Grafik Eye and Home Works Dimming Interfaces. Emergency Option: Remote Emergency attery ack-up for minimum 90 minute operation. Mounted adjacent to fixture during installation. Remote test switch, plate cover and junction box included. See ordering guide for battery operated wattage. Damp location rated. 120V/277V AC operation. Junction ox:16 gauge pre-wired galvanized steel Junction ox, 32 cubic-inch for a maximum of () #12 AWG wires. Furnished with (7) 3/4" and (4) Romex knock-outs. Strain clamps to install or remove covers for easy access and ground wire. Equipped with safety standard fitting for flex-conduit. Insulation Contact: Energy Efficient housing comes standard with IC rating for direct contact with loosefill blown and rolled insulation. Mounting Steel pressure springs mounted on trim to ensure positive retention inside housing. Power Connection: heat sinked lamp module is replaceable via onboard quick exclusionary disconnect terminal. No tools required. Meets CA Title 24 Requirements and other standards restricting the use of Medium ase or i-pin Sockets. Thermal Management: LM0 tested to achieve a minimum of 35,000 hour L70 life based proper heat dissipation facilitated by integral aluminum heat sink that maximizes heat rejection. Warranty: Covered by a 3 Year Warranty to be free of defects in materials and craftsmanship. Recommended for applications where ambient temperatures do not exceed 35 C, installations exceeding this temperature will result in reduced lamp life and a voided warranty. Label: cetl Listed Assembled in USA FEATURE(S): 6" IC HOUSING LHLD6 DRIVER LHLD615C70 :120V LHLD615C70-DIN :Incandescent Dimming LHLD615C70-UE :120V/277V :None -EM :Emergency ack-up (6W) -EM2 :Emergency ack-up (10W) 6" AMER REFLECTOR LRLD621 Ordering example: LHLD610C50-DIN/LRLD621-TAM-25 EAM SPREAD LRLD621-TAM-LVR :All lack -25:Narrow Flood LRLD621W-TAM-LVR :All White -45:Flood -61:Wide Flood L I G H T I N G G R O U P

6 : L31-7" ROUND OLLARD LM - Amber (Turtle Safe) OLLARD 6 5 / 3 1 / 2 CONDUIT OPENING 37 3 / X 13 / / OLT HOLES CIRCLE Ground Mount Hole Location 2W Application: ollards are designed for indoor and outdoor applications where low-level illumination is required. ollards are used to light walkways, public gathering spaces, gardens, along waterfronts and marinas and other public and private areas. Luminaire Construction: High grade extruded aluminum tube with die cast aluminum top and base. The luminaire is secured to the base by three (3) tamper resistant, stainless steel set screws. ase is mounted to Anchor olt Assembly Kit by three (3) nuts and washers. Note: A solid foundation for installation is recommended. Luminaire Enclosure: Flat, one-piece top is constructed of heavy duty die cast aluminum housing with a powder coat finish. A clear U.V. stabilized polycarbonate molded lens, interior anodized aluminum louvers and top anodized reflector provides a 360 symmetrical light distribution. Luminaire enclosure is secured to lower housing by three (3) tamper resistant, stainless steel set screws and silicone gasket for quick installation and/or relamping. No visible HARR Up to 3% energy savings Glare Free Corrosion-resistant polyester powder coat finish Available in lack, White, Silver and Architectural ronze 120V/277V standard Universal Dimming option dims with ELV, 2-Wire 0-10 Dimming Systems 5-Year Limited Warranty Up to 20' O.C spacing Type I, III, & V Distributions Available Emergency Options Available Thermal Management: Effective thermal dissipation facilitated by integral cast-aluminum, heat sink design for maximum heat rejection to provide long life Dimming: (-DUN) option is a universal dimming system that works with most 3-Wire ELV, 2- Wire Incandescent and 5-Wire 0-10V fluorescent dimmers. Electrical: Through wiring, a maximum of four (4) No. 12 AWG conductors (plus ground wire), rated 90 C min. A 3 diameter conduit opening at base bottom provided. Listing: ETL / cetl Listed. Suitable for wet location. (IP65) Finish: Available in lack, Architectural ronze, Silver* and White*. : Available in 3000K, 4000K and 5000K. Distribution: Available in Type V - Symmetrical, Type 0I - 10 Forward Throw* and Type III - 90 Wide Forward Throw*. FEATURE: ORDERING EXAMPLE : L31UE-T30 L31 L31 FIXTURE REFLECTOR :lack - :lack Z S W :Architectural ronze :White* UE :120V/277V -TAM-LVR :590nm AMER* UE-DUN:UniDim 120V/277V* -0I -III DISTRIUTION :Type V - Symmetrical :Type 0I - 10 Forward Throw* :Type III - 90 Wide Forward Throw* :None EM :25W Remote Emergency EMA :25W Integral Emergency * Special Order. Minimum order or extended lead time may apply. Consult Factory. LIGHTING GROU P

7 : L721 - " X 4" SCOOP OLLARD (IP65) - 50LM - Amber (Turtle Safe) OLLARD 1/ 1 / 1/ / 16 L / Application: This single head bollard is designed for outdoor applications where a Dark Sky compliant illumination is required. ollards are used to light walkways, public gathering spaces, gardens, along waterfronts and marinas and other public and private areas. Dimming: (UE-DUN) option is a universal dimming system that works with most 3-Wire ELV, 2-Wire Incandescent and 5-Wire 0-10V fluorescent dimmers. Electrical: driver, 120VAC, 50/60Hz, electronic Constant Current, Class 2, Power Factor >.90pf, integrally mounted. Use driver option UE-DUN UniDim (120V/277V) for dimming (see above), and cold weather applications (-30 C and above) Emergency Options: Emergency attery ack-up available, remotely mounted adjacent to housing by installer. When AC power fails, the device immediately switches to the emergency mode, operating the s for a minimum of 90 minutes. Remote test switch, Caution: LITON recommends use of surge protectors on the power entering Housings. Note: Dark Sky compliant / 16 L Listing: ETL / cetl Listed. Suitable for wet location. Assembled in USA. (IP65) / 2 Ground Mount Hole Location Finish: Available in lack, White*, ronze*, and Silver*. : inned with 4-step MacAdam ellipses as recommended by Post: High grade rectangular extruded aluminum with a high grade powder coat finish. ANSI Standard. Available in 4000K and 3000K. Includes liquid tight plug for cord entry and a zinc plated steel base with a high grade powder coat finish and an anchor bolt kit. The base is secured to the post by four (4) tamper resistant, Details: ~ 50 + Lumens Delivered stainless steel flat head screws and the base is mounted to the ground by four (4) anchor bolts Color Rendering Index (CRI): 90 and eight () nuts and washers. Note: A solid foundation for installation is recommended. Post Color Temperature: 4000K can accommodate daisy chain and through wiring. Lamp Equivalents: 26W CFL 75W A19 Head: Constructed from a two (2) piece high grade die cast aluminum with a high grade powder coat finish. Includes a clear tempered glass lens (sits flush to the head), array, Sleek architectural design reflector, driver, silicone gasket and a hole with liquid tight plugs for cord to exit the post. Durable, corrosion resistant finish The two piece housing is secured together by four (4) tamper resistant stainless steel set screws and is secured to the post by two stainless steel screws. Thermal Management: Effective thermal dissipation facilitated by integral cast-aluminum, finned heat sink design for maximum heat rejection to provide long life. FEATURE: ORDERING EXAMPLE : L T30-EMA L721 L721 Wet Location US Assembled HEIGHT LENS -20 :20 :lack :Clear :Non-Dimming (120V) -TAM-LVR:590nm AMER* -40 :40 W :White* -FR :Frosted UE-DUN :UniDim (120V/277V) -EMA :Integral :None Emergency ack Up Z :ronze* -SDL :Daylight Sensor S L I G H T I N G G R O U P

8 : L731 - " X 4" TRAPEZOID OLLARD (IP65) - 50LM - Amber (Turtle Safe) OLLARD 1/ 1/ 1/ / 16 L / Application: This single head bollard is designed for outdoor applications where a Dark Sky compliant illumination is required. ollards are used to light walkways, public gathering spaces, gardens, along waterfronts and marinas and other public and private areas. Dimming: (UE-DUN) option is a universal dimming system that works with most 3-Wire ELV, (UE-DUN) option is a2-wire Incandescent and 5-Wire 0-10V fluorescent dimmers. Electrical: driver, 120VAC, 50/60Hz, electronic Constant Current, Class 2, Power Factor >.90pf, integrally mounted. Use driver option UE-DUN UniDim (120V/277V) for dimming (see above), and cold weather applications (-30 C and above) Emergency Options: Emergency attery ack-up available, remotely mounted adjacent to housing by installer. When AC power fails, the device immediately switches to the emergency mode, operating the s for a minimum of 90 minutes. Remote test switch, Caution: LITON recommends use of surge protectors on the power entering Housings. Note: Dark Sky compliant / 16 L Listing: ETL / cetl Listed. Suitable for wet location. Assembled in USA. (IP65). Finish: Available in lack, White*, ronze*, and Silver*. : inned with 4-step MacAdam ellipses as recommended by Post: High grade rectangular extruded aluminum with a high grade powder coat finish. ANSI Standard. Available in 4000K and 3000K. Includes liquid tight plug for cord entry and a zinc plated steel base with a high grade powder coat finish and an anchor bolt kit. The base is secured to the post by four (4) tamper resistant, Details: ~ 50 + Lumens Delivered stainless steel flat head screws and the base is mounted to the ground by four (4) anchor bolts Color Rendering Index (CRI): 90 and eight () nuts and washers. Note: A solid foundation for installation is recommended. Post Color Temperature: 4000K can accommodate daisy chain and through wiring. Lamp Equivalents: 26W CFL 75W A19 Head: Constructed from a two (2) piece high grade die cast aluminum with a high grade powder coat finish. Includes a clear tempered glass lens (sits flush to the head), array, Sleek architectural design reflector, driver, silicone gasket and a hole with liquid tight plugs for cord to exit the post. Durable, corrosion resistant finish The two piece housing is secured together by four (4) tamper resistant stainless steel set screws and is secured to the post by two stainless steel screws. Thermal Management: Effective thermal dissipation facilitated by integral cast-aluminum, finned heat sink design for maximum heat rejection to provide long life / 2 Ground Mount Hole Location FEATURE: ORDERING EXAMPLE : L TAM-LVR-EMA L731 L731 Wet Location US Assembled HEIGHT LENS -20 :20 :lack :Clear -TAM-LVR :590nm AMER* -40 :40 W :White* -FR :Frosted Z :ronze* S -EMA :Integral :None Emergency ack Up -SDL :Daylight Sensor L I G H T I N G G R O U P

9 : WD " X 4" SCOOP 1-DIRECTION WALL MOUNT (IP65) - 50LM - Amber (Turtle Safe) SURFACE 1-DIRECTION WALL MOUNT Application: This WD1 Series directional wall luminaire can be used in both indoor and outdoor settings and can be pointed up or down. Typical locations are in commercial and retail spaces that contain walls and/or columns that require directional lighting. they can be used as downlight for direct illumination or as uplights for indirect illumination of architecture facades. Housing: Constructed from two (2) pieces of high grade die cast aluminum with a high grade powder coat finish. Includes a faceplate with a tempered glass lens (sits flush to the housing), array, reflector, driver, silicone gasket and a wire exit hole to junction box wiring. The two piece housing is secured together by four (4) tamper resistant stainless steel set screws. Mounting: The fixture mounts on to a wall directly over standard 3-1/2" junction box or other similar size junction boxes. Faceplate: One piece die cast aluminum with powder coat finish, and a tempered glass lens (available in clear or frosted). Reflector Construction: The one piece, heavy-gauge aluminum reflector prevents ugly dents during shipping and installation. Deeply mounted singular provides 50 degree visual Finish: A 7-stage electrostatic, polymer process provides a finish resistance to corrosion and UV-degradation Available in lack, White*, ronze and Silver*. : inned with 4-step MacAdam ellipses as recommended by ANSI Standard. Available in 4000K and 3000K. Details: ~ 50 + Lumens Delivered Color Rendering Index (CRI): 90 Color Temperature: 4000K Lamp Equivalents: 26W CFL 75W A19 Sleek architectural design Durable, corrosion resistant finish Thermal Management: Effective thermal dissipation facilitated by integral cast-aluminum, finned heat sink design for maximum heat rejection to provide long life. Dimming: (UE-DUN) option is a universal dimming system that works with most 3-Wire ELV, 2- Wire Incandescent and 5-Wire 0-10V fluorescent dimmers. Electrical: driver, 120VAC, 50/60Hz, electronic Constant Current, Class 2, Power Factor >.90pf, integrally mounted. Use driver option UE-DUN UniDim (120V/277V) for dimming (see above), and cold weather applications (-30 C and above). Emergency Options: Emergency attery ack-up available, remotely mounted adjacent to housing by installer. When AC power fails, the device immediately switches to the emergency mode, operating the s for a minimum of 90 minutes. Remote test switch, Caution: LITON recommends use of surge protectors on the power entering Housings. Note: Dark Sky compliant when fixture is pointing downward. Listing: ETL / cetl Listed. Suitable for wet location. Assembled in USA. (IP65). FEATURE: ORDERING EXAMPLE : WD1472-T30-EMAC WD1472 WD1472 WZ Z S :lack :White* :ronze LENS :Clear -FR :Frosted UE-DUN :Non-Dimming :UniDim (120V/277V) -TAM-LVR:590nm AMER* :Emergency -EMAC :None ack Up L I G H T I N G G R O U P

10 : WD " X 4" TRAPEZOID 1-DIRECTION WALL MOUNT (IP65) - 50LM - Amber (Turtle Safe) SURFACE 1-DIRECTION WALL MOUNT Application: This WD1 Series directional wall luminaire can be used in both indoor and outdoor settings and can be pointed up or down. Typical locations are in commercial and retail spaces that contain walls and/or columns that require directional lighting. they can be used as downlight for direct illumination or as uplights for indirect illumination of architecture facades. Housing: Constructed from two (2) pieces of high grade die cast aluminum with a high grade powder coat finish. Includes a faceplate with a tempered glass lens (sits flush to the housing), array, reflector, driver, silicone gasket and a wire exit hole to junction box wiring. The two piece housing is secured together by four (4) tamper resistant stainless steel set screws. Mounting: The fixture mounts on to a wall directly over standard 3-1/2" junction box or other similar size junction boxes. Faceplate: One piece die cast aluminum with powder coat finish, and a tempered glass lens (available in clear or frosted). Reflector Construction: The one piece, heavy-gauge aluminum reflector prevents ugly dents during shipping and installation. Deeply mounted singular provides 50 degree visual Finish: A 7-stage electrostatic, polymer process provides a finish resistance to corrosion and UV-degradation Available in lack, White*, ronze and Silver*. : inned with 4-step MacAdam ellipses as recommended by ANSI Standard. Available in 4000K and 3000K. Details: ~ 50 + Lumens Delivered Color Rendering Index (CRI): 90 Color Temperature: 4000K Lamp Equivalents: 26W CFL 75W A19 Sleek architectural design Durable, corrosion resistant finish Thermal Management: Effective thermal dissipation facilitated by integral cast-aluminum, finned heat sink design for maximum heat rejection to provide long life. Dimming: (UE-DUN) option is a universal dimming system that works with most 3-Wire ELV, 2-Wire Incandescent and 5-Wire 0-10V fluorescent dimmers. Electrical: driver, 120VAC, 50/60Hz, electronic Constant Current, Class 2, Power Factor >.90pf, integrally mounted. Use driver option UE-DUN UniDim (120V/277V) for dimming (see above), and cold weather applications (-30 C and above). Emergency Options: Emergency attery ack-up available, remotely mounted adjacent to housing by installer. When AC power fails, the device immediately switches to the emergency mode, operating the s for a minimum of 90 minutes. Remote test switch, Caution: LITON recommends use of surge protectors on the power entering Housings. Note: Dark Sky compliant when fixture is pointing downward. Listing: ETL / cetl Listed. Suitable for wet location. Assembled in USA. (IP65). FEATURE: ORDERING EXAMPLE : WD1473 WD1473 WD1473 WZ Z S :lack :White* :ronze LENS :Clear -FR :Frosted UE-DUN :Non-Dimming :UniDim (120V/277V) -TAM-LVR:590nm AMER* :Emergency -EMAC :None ack Up L I G H T I N G G R O U P