BATWING- ROTARY CUTTER BW15.50 BW15.50Q BW10.50 BW10.50Q OPERATOR'S MANUAL MAN1237. (Rev. 12/11/2017)

Transcription

1 MAN1237 (Rev. 12/11/2017) BATWING- ROTARY CUTTER BW15.50 BW15.50Q BW10.50 BW10.50Q OPERATOR'S MANUAL

2 TO THE DEALER: Assembly and proper installation of this product is the responsibility of the Woods dealer. Read manual instructions and safety rules. Make sure all items on the Dealer s Pre-Delivery and Delivery Check Lists in the Operator s Manual are completed before releasing equipment to the owner. The dealer must complete the online Product Registration form at the Woods Dealer Website which certifies that all Dealer Check List items have been completed. Dealers can register all Woods product at dealer.woodsequipment.com under Product Registration. Failure to register the product does not diminish customer s warranty rights. TO THE OWNER: Read this manual before operating your Woods equipment. The information presented will prepare you to do a better and safer job. Keep this manual handy for ready reference. Require all operators to read this manual carefully and become acquainted with all adjustment and operating procedures before attempting to operate. Replacement manuals can be obtained from your dealer. To locate your nearest dealer, check the Dealer Locator at or in the United States and Canada call The equipment you have purchased has been carefully engineered and manufactured to provide dependable and satisfactory use. Like all mechanical products, it will require cleaning and upkeep. Lubricate the unit as specified. Observe all safety information in this manual and safety decals on the equipment. For service, your authorized Woods dealer has trained mechanics, genuine Woods service parts, and the necessary tools and equipment to handle all your needs. Use only genuine Woods service parts. Substitute parts will void the warranty and may not meet standards required for safe and satisfactory operation. Record the model number and serial number of your equipment in the spaces provided: Model: _ Date of Purchase: Serial Number: (see Safety Decal section for location) Provide this information to your dealer to obtain correct repair parts. Throughout this manual, the term NOTICE is used to indicate that failure to observe can cause damage to equipment. The terms CAUTION, WARNING, and DANGER are used in conjunction with the Safety-Alert Symbol (a triangle with an exclamation mark) to indicate the degree of hazard for items of personal safety. 2 Introduction Gen l (Rev. 2/25/2016)

3 TABLE OF CONTENTS INTRODUCTION SPECIFICATIONS GENERAL INFORMATION SAFETY VIDEO ORDER FORM SAFETY RULES SAFETY DECALS OPERATION OWNER SERVICE TROUBLESHOOTING DEALER SERVICE ASSEMBLY INSTRUCTIONS DEALER CHECK LISTS INDEX TO PARTS LISTS BOLT TORQUE CHART BOLT SIZE CHART & ABBREVIATIONS INDEX PRODUCT WARRANTY REPLACEMENT PARTS WARRANTY BACK COVER! LEA EL INSTRUCTIVO! Si no lee Ingles, pida ayuda a alguien que si lo lea para que le traduzca las medidas de seguridad. This Operator s Manual should be regarded as part of the machine. Suppliers of both new and second-hand machines must make sure that this manual is provided with the machine. MAN1237 (9/1/2017) Introduction 3

4 SPECIFICATIONS BW15.50 / BW15.50Q BW10.50 / BW10.50Q Cutting Height (Varies with tire selection) " - 15" 1" - 15" Cutting Width " (15 ) 126" (10.5 ) Overall Width " 140" Transport Width " 93" Transport Height " 85-90" Tractor HP Tractor Min. PTO hp Tractor PTO rpm / /1000 Blade Spindle Blade Overlap " 6" Number of Blades Blade Rotation Left Spindle: CW; Right & Center Spindles: CCW Blade Speed (feet per minute) ,000/16,000 15,000/16,000 Wing Driveline Cat 4 Cat 4 CV Driveline Cat 6 Cat 6 Side Frame Thickness /4" 1/4" Weight (approximate lbs.) Tongue Weight (approximate lbs.) Wheel Size " Rims (BW15.50 and BW15.50Q only), 21" OD Solid Tires, 25" Severe Duty, 29" Airplane Torsion Protection Slip Clutch Slip Clutch GENERAL INFORMATION WARNING Some illustrations in this manual show the equipment with safety shields removed to provide a better view. This equipment should never be operated with any necessary safety shielding removed. The purpose of this manual is to assist you in operating and maintaining your cutter. Read it carefully. It furnishes information and instructions that will help you achieve years of dependable performance. These instructions have been compiled from extensive field experience and engineering data. Some information may be general in nature due to unknown and varying operating conditions. However, through experience and these instructions, you should be able to develop procedures suitable to your particular situation. The illustrations and data used in this manual were current at the time of printing but, due to possible inline production changes, your machine may vary slightly in detail. We reserve the right to redesign and change the machines as may be necessary without notification. Throughout this manual, references are made to right and left directions. These are determined by standing behind the equipment facing the direction of forward travel. Blade rotation is clockwise (left wing) and counterclockwise (right wing and center section) as viewed from the top of the cutter. 4 Introduction MAN1237 (9/1/2017)

5 BE SAFE! Safety Video Order Form BE ALERT! BE ALIVE! BE TRAINED Before Operating Mowers! ASSOCIATION OF EQUIPMENT MANUFACTURERS Safety Training Does Make a Difference. Free Mower Safety Video Fill out and return the order form and we will send you a FREE VHS or DVD video outlining Industrial and Agricultural Mower Safety Practices. The 22 minute video, developed in cooperation with AEM (Association of Equipment Manufacturers), reinforces the proper procedures to follow while operating your mowing equipment. The video does not replace the information contained in the Operator s Manual, so please review this manual thoroughly before operating your new mowing equipment. Safety Video Order Form (8/2/2005) Safety 5

6 Also, available from the Association of Equipment Manufacturers: A large variety of training materials (ideal for groups) are available for a nominal charge from AEM. Following is a partial list: Training Package for Rotary Mowers/Cutters-English Contains: DVD & VHS (English) Guidebook for Rotary Mowers/Cutters (English) AEM Industrial/Agricultural Mower Safety Manual (English) AEM Agricultural Tractor Safety Manual (English) Training Package for Rotary Mowers/Cutters-English/Spanish Contains: DVD & VHS (English/Spanish) Guidebook for Rotary Mowers/Cutters (English/Spanish) AEM Industrial/Agricultural Mower Safety Manual (English/Spanish) AEM Agricultural Tractor Safety Manual (English/Spanish) AEM training packages are available through: AEM at: or Universal Lithographers, Inc. aem@ulilitho.com tel fax Free Mower/Cutter Safety Video Order Form Please send me (Select one) VHS Format - VHS01052 Safety Video DVD Format - DVD01052 Safety Video Name: _ Phone: Address: _ Mower/Cutter Model: _ Serial #: Send to: ATTENTION: DEALER SERVICES WOODS EQUIPMENT COMPANY PO BOX 1000 OREGON IL USA 6 Safety Safety Video Order Form (Rev. 2/6/2006)

7 SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Safety is a primary concern in the design and manufacture of our products. Unfortunately, our efforts to provide safe equipment can be wiped out by an operator s single careless act. In addition to the design and configuration of equipment, hazard control and accident prevention are dependent upon the awareness, concern, judgement, and proper training of personnel involved in the operation, transport, maintenance, and storage of equipment. It has been said, The best safety device is an informed, careful operator. We ask you to be that kind of operator. INSTALLATION Hydraulics must be connected as instructed in this manual. Do not substitute parts, modify, or connect in any other way. TRAINING Safety instructions are important! Read all attachment and power unit manuals; follow all safety rules and safety decal information. (Replacement manuals and safety decals are available from your dealer. To locate your nearest dealer, check the Dealer Locator at or in the United States and Canada call ) Failure to follow instructions or safety rules can result in serious injury or death. If you do not understand any part of this manual and need assistance, see your dealer. Know your controls and how to stop engine and attachment quickly in an emergency. Operators must be instructed in and be capable of the safe operation of the equipment, its attachments, and all controls. Do not allow anyone to operate this equipment without proper instructions. Keep hands and body away from pressurized lines. Use paper or cardboard, not hands or other body parts to check for leaks. Wear safety goggles. Hydraulic fluid under pressure can easily penetrate skin and will cause serious injury or death. Make sure that all operating and service personnel know that if hydraulic fluid penetrates skin, it must be surgically removed as soon as possible by a doctor familiar with this form of injury or gangrene, serious injury, or death will result. BW15_SR (12/7/2017) CONTACT A PHYSICIAN IMMEDIATELY IF FLUID ENTERS SKIN OR EYES. DO NOT DELAY. Never allow children or untrained persons to operate equipment. PREPARATION Check that all hardware is properly installed. Always tighten to torque chart specifications unless instructed otherwise in this manual. Air in hydraulic systems can cause erratic operation and allows loads or equipment components to drop unexpectedly. When connecting equipment or hoses or performing any hydraulic maintenance, purge any air in hydraulic system by operating all hydraulic functions several times. Do this before putting into service or allowing anyone to approach the equipment. Make sure all hydraulic hoses, fittings, and valves are in good condition and not leaking before starting power unit or using equipment. Check and route hoses carefully to prevent damage. Hoses must not be twisted, bent sharply, kinked, frayed, pinched, or come into contact with any moving parts. Operate moveable components through full operational range to check clearances. Replace any damaged hoses immediately. After connecting hoses, check that all control lever positions function as instructed in the Operator's Manual. Do not put into service until control lever and equipment movements are correct. Set tractor hydraulic relief valve at 2500 psi (170 bars) (17,000 kpa) to prevent injury and equipment damage due to hydraulic system failure. Your dealer can supply original equipment hydraulic accessories and repair parts. Substitute parts may not meet original equipment specifications and may be dangerous. Always wear relatively tight and belted clothing to avoid getting caught in moving parts. Wear sturdy, rough-soled work shoes and protective equipment for eyes, hair, hands, hearing, and head; and respirator or filter mask where appropriate. Make sure attachment is properly secured, adjusted, and in good operating condition. Make sure spring-activated locking pin or collar slides freely and is seated firmly in tractor PTO spline groove. (Safety Rules continued on next page) Safety 7

8 SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! (Safety Rules continued from previous page) Make sure driveline guard tether chains are attached to the tractor and equipment as shown in the pamphlet that accompanies the driveline. Replace if damaged or broken. Check that driveline guards rotate freely on driveline before putting equipment into service. Before starting power unit, check all equipment driveline guards for damage. Replace any damaged guards. Make sure all guards rotate freely on all drivelines. If guards do not rotate freely on drivelines, repair and replace bearings before putting equipment into service. Power unit must be equipped with ROPS or ROPS cab and seat belt. Keep seat belt securely fastened. Falling off power unit can result in death from being run over or crushed. Keep foldable ROPS system in locked up position at all times. Remove accumulated debris from this equipment, power unit, and engine to avoid fire hazard. Make sure all safety decals are installed. Replace if damaged. (See Safety Decals section for location.) Make sure shields and guards are properly installed and in good condition. Replace if damaged. Do not put this equipment into service unless all side skids are properly installed and in good condition. Replace if damaged. A minimum 25% of tractor and equipment weight must be on the tractor front wheels when attachments are in transport position. Without this weight, front tractor wheels could raise up resulting in loss of steering. The weight may be attained with front wheel weights, ballast in tires, front tractor weights or front loader. Weigh the tractor and equipment. Do not estimate. Inspect and clear area of stones, branches, or other hard objects that might be thrown, causing injury or damage. Connect PTO driveline directly to power unit PTO shaft. Never use adapter sleeves or adapter shafts. Adapters can cause driveline failures due to incorrect spline or incorrect operating length and can result in personal injury or death. TRANSPORTATION Power unit must be equipped with ROPS or ROPS cab and seat belt. Keep seat belt securely fastened. Falling off power unit can result in death from being run over or crushed. Keep foldable ROPS system in locked up position at all times. Always raise unit and install transport locks before transporting. Leak down or failure of mechanical or hydraulic system can cause equipment to drop. Always attach safety chain to tractor drawbar when transporting unit. Always comply with all state and local lighting and marking requirements. Never allow riders on power unit or attachment. Do not operate PTO during transport. Do not operate or transport on steep slopes. Do not operate or transport equipment while under the influence of alcohol or drugs. The maximum transport speed for towed and semi-mounted machines is 20 mph (32 km/h). Regardless of the maximum speed capability of the towing tractor, do not exceed the implement s maximum transport speed. Doing so could result in: Loss of control of the implement and tractor Reduced or no ability to stop during braking Implement tire failure Damage to the implement or its components. Use additional caution and reduce speed when under adverse surface conditions, turning, or on inclines. Never tow this implement with a motor vehicle. OPERATION Do not allow bystanders in the area when operating, attaching, removing, assembling, or servicing equipment. Never walk, stand, or place yourself or others under a raised wing or in the path of a lowering wing. Hydraulic system leak-down, hydraulic system failures, mechanical failures, or movement of control levers can cause wings to drop unexpectedly and cause severe injury or death. (Safety Rules continued on next page) 8 Safety BW15_SR (12/7/2017)

9 SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! (Safety Rules continued from previous page) Full chain shielding must be installed at all times. Thrown objects could injure people or damage property. If the machine is not equipped with full chain shielding, operation must be stopped. This shielding is designed to reduce the risk of thrown objects. The mower deck and protective devices cannot prevent all objects from escaping the blade enclosure in every mowing condition. It is possible for objects to ricochet and escape, traveling as much as 300 feet (92m). Never direct discharge toward people, animals, or property. Do not operate or transport equipment while under the influence of alcohol or drugs. Operate only in daylight or good artificial light. Keep hands, feet, hair, and clothing away from equipment while engine is running. Stay clear of all moving parts. Always comply with all state and local lighting and marking requirements. Never allow riders on power unit or attachment. Power unit must be equipped with ROPS or ROPS cab and seat belt. Keep seat belt securely fastened. Falling off power unit can result in death from being run over or crushed. Keep foldable ROPS system in locked up position at all times. Always sit in power unit seat when operating controls or starting engine. Securely fasten seat belt, place transmission in neutral, engage brake, and ensure all other controls are disengaged before starting power unit engine. Operate tractor PTO at 540 RPM (1000 RPM on Q Series cutters). Do not exceed. Raise or lower wings slowly to prevent personal injury or damage to cutter. Look down and to the rear and make sure area is clear before operating in reverse. Do not operate or transport on steep slopes. BW15_SR (12/7/2017) Do not stop, start, or change directions suddenly on slopes. Watch for hidden hazards on the terrain during operation. Stop power unit and equipment immediately upon striking an obstruction. Turn off engine, set parking brake, remove key, inspect, and repair any damage before resuming operation. Continuous operation while the clutch is slipping could cause heat build-up resulting in fire. Adjust slip clutch pressure by tightening springs to the dimension shown in the Owner Service section. If clutch is set to minimum spring length, replace the friction disks as shown. MAINTENANCE Before servicing, adjusting, repairing or unplugging, stop tractor engine, place all controls in neutral, set park brake, remove ignition key, and wait for all moving parts to stop. Before dismounting power unit or performing any service or maintenance, follow these steps: disengage power to equipment, lower the 3-point hitch and all raised components to the ground, operate valve levers to release any hydraulic pressure, set parking brake, stop engine, remove key, and unfasten seat belt. Do not modify or alter or permit anyone else to modify or alter the equipment or any of its components in any way. Your dealer can supply original equipment hydraulic accessories and repair parts. Substitute parts may not meet original equipment specifications and may be dangerous. To prevent contamination during maintenance and storage, clean and then cover hose ends, fittings, and hydraulic ports with tape. Do not allow bystanders in the area when operating, attaching, removing, assembling, or servicing equipment. (Safety Rules continued on next page) Safety 9

10 SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! (Safety Rules continued from previous page) Never go underneath equipment (lowered to the ground or raised) unless it is properly blocked and secured. Never place any part of the body underneath equipment or between moveable parts even when the engine has been turned off. Hydraulic system leak down, hydraulic system failures, mechanical failures, or movement of control levers can cause equipment to drop or rotate unexpectedly and cause severe injury or death. Follow Operator's Manual instructions for working underneath and blocking requirements or have work done by a qualified dealer. Keep all persons away from operator control area while performing adjustments, service, or maintenance. Make certain all movement of equipment components has stopped before approaching for service. Frequently check blades. They should be sharp, free of nicks and cracks, and securely fastened. Do not handle blades with bare hands. Careless or improper handling may result in serious injury. Your dealer can supply genuine replacement blades. Substitute blades may not meet original equipment specifications and may be dangerous. Tighten all bolts, nuts, and screws to torque chart specifications. Check that all cotter pins are installed securely to ensure equipment is in a safe condition before putting unit into service. Make sure all safety decals are installed. Replace if damaged. (See Safety Decals section for location.) Make sure shields and guards are properly installed and in good condition. Replace if damaged. Never perform service or maintenance with engine running. Do not disconnect hydraulic lines until machine is securely blocked or placed in lowest position and system pressure is released by operating valve levers. Service and maintenance work not covered in OWNER SERVICE must be done by a qualified dealership. Special skills, tools, and safety procedures may be required. Failure to follow these instructions can result in serious injury or death. Explosive separation of tire and rim parts can cause serious injury or death. Release all air pressure before loosening bolts on wheel. STORAGE Before disconnecting and storing, follow these instructions: Store on level, solid ground. Disconnect driveline and secure up off the ground. Lower wings to ground. Raise cutter center section and pin transport bar in raised position. Attach parking jack and raise tongue weight off tractor drawbar. Place wedge blocks at front and rear of wheels on center section and each wing to prevent wheel rotation. Securely block all four corners of center section and each wing with jackstands. Remove hydraulic hoses after tractor is turned off and all system pressure is released by operating valve levers several times. Remove safety tow chain. Remove retainer pin and high strength drawbar pin. Keep children and bystanders away from storage area. 10 Safety BW15_SR (12/7/2017)

11 SAFETY & INSTRUCTIONAL DECALS ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Replace Immediately If Damaged! 1 - SERIAL NUMBER PLATE PN Located on Wheel Rims BE CAREFUL! Use a clean, damp cloth to clean safety decals. Avoid spraying too close to decals when using a pressure washer; high-pressure water can enter through very small scratches or under edges of decals causing them to peel or come off. Replacement safety decals can be ordered free from your Woods dealer. To locate your nearest dealer, check the Dealer Locator at or in the United States and Canada call FRONT AMBER REFLECTOR (PN ) 3 - REAR RED REFLECTOR (PN 57123) MAN1237 (9/1/2017) Safety 11

12 SAFETY & INSTRUCTIONAL DECALS ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Replace Immediately If Damaged! 8 - PN PN (1000 RPM) OR 6 - PN (540 RPM) 7 - PN PN PN PN Safety MAN1237 (9/1/2017)

13 SAFETY & INSTRUCTIONAL DECALS ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Replace Immediately If Damaged! 12 - PN PN PN PN PN PN PN MAN1237 (9/1/2017) Safety 13

14 OPERATION The designed and tested safety of this machine depends on it being operated within the limitations as explained in this manual. Be familiar with and follow all safety rules in the manual, on the cutter and on the tractor. The safe operation of this cutter is the responsibility of the operator, who must be properly trained. The operator should be familiar with the equipment and all safety practices before starting operation. Read the safety information on page 7 through page 13. Recommended tractor ground speed for most conditions is from 1 to 6 mph. Always operate tractor PTO at 540 rpm on BW15.50 and BW10.50; on BW15.50Q and BW10.50Q operate PTO at 1,000 rpm. DANGER Full chain shielding must be installed at all times. Thrown objects could injure people or damage property. If the machine is not equipped with full chain shielding, operation must be stopped. This shielding is designed to reduce the risk of thrown objects. The mower deck and protective devices cannot prevent all objects from escaping the blade enclosure in every mowing condition. It is possible for objects to ricochet and escape, traveling as much as 300 feet (92m). WARNING Never allow children or untrained persons to operate equipment. Do not allow bystanders in the area when operating, attaching, removing, assembling, or servicing equipment. equipment for eyes, hair, hands, hearing, and head; and respirator or filter mask where appropriate. CONNECTING CUTTER TO TRACTOR NOTICE For tractors with a 1-3/8" diameter PTO shaft, the horizontal distance from the end of the tractor PTO shaft to the center of drawbar pin should be 14" for 540 rpm cutter and 16" for the 1000 rpm cutters. This will minimize joint knock and damage to drive components. Use of the CV Lift Assist System The Batwing cutter has a system to help lift and support the driveline while connecting and disconnecting it from the tractor. Follow the instructions below. 1. Remove klik pin. 2. Lift lever to vertical position which will lift driveline. 3. Connect coupler to tractor pto shaft. 4. Lower lever and secure with klik pin. If the driveline is held too high or low, the roller carriage can be adjusted by removing the mounting bolts, moving it to the preferred position, and replacing the bolts. NOTICE If the tractor used to power the Batwing has a PTO shaft and drawbar closer than the current standards, the driveline could contact the lift assist frame or roller during use and could cause damage and failure to the driveline. When using a tractor of this type, the CV lift assist system should be removed from the tongue to avoid potential contact and damage. Make sure spring-activated locking pin or collar slides freely and is seated firmly in tractor PTO spline groove. CAUTION Stop power unit and equipment immediately upon striking an obstruction. Turn off engine, remove key, inspect, and repair any damage before resuming operation. Always wear relatively tight and belted clothing to avoid getting caught in moving parts. Wear sturdy, rough-soled work shoes and protective Figure 1. Cutter to Tractor Connection 14 Operation MAN1237 (9/1/2017)

15 Mechanical Connection 1. Attach cutter using a 1-1/8" clevis pin and clip. 2. Attach safety tow chain (25) to drawbar support. Leave enough slack for turning. 3. Connect cutter driveline to tractor PTO shaft, making sure the spring-activated lock pin slides freely and is seated in tractor PTO splined groove. 4. Attach driveline shield tether chain to tractor drawbar to prevent rotation, if desired. NOTE: CV driveline does not require a tether chain. 5. Loosen bolts in jack mount. Adjust jack so foot plate sits flat for storage. Tighten bolts. 6. Remove parking jack (16) from the tongue and attach it to the storage post on the front of the left wing. Hydraulic Connection 1. Inspect hydraulic hoses to ensure they are in good condition. 2. Clean the fittings before connecting them to the tractor hydraulic ports. 3. Route the hose through the hose holder at the hitch and be sure the hose can slide freely in the holder. Do not allow hose slack to drag on the ground or become caught on tractor protrusions. 4. Attach the hydraulic hose to the tractor. 5. From the operator position, start tractor and raise and lower deck several times to purge trapped air from the hydraulic cylinder. Interference Check 1. Be sure that tractor 3-point lift links do not interfere with hydraulic hoses, cutter driveline, or cutter frame. 2. Check for straight-ahead operation and at full turning angles. If there is any interference, remove the lower lift links. 3. Contact between tractor lift links and cutter parts can cause damage, especially when turning. CV Driveline Turning Limits NOTICE You must not exceed a turning angle of 80 degrees at the head of the Constant Velocity driveline or damage will occur. NOTE: Remove CV drive shipping bracket before operation and discard. This bracket is only supplied on factory assembled units with a CV drive installed. MAN1237 (9/1/2017) 1. To check for potential excessive turn angle, disconnect the driveline from tractor. 2. Start engine and turn as far right or left as possible. 3. Shut engine off and try to connect CV driveline to tractor. If it cannot be connected, the turn angle is too severe. 4. Restart engine and straighten angle slightly, shut off engine and try to connect CV driveline to tractor. 5. Repeat the process until the driveline can be connected. The point at which the driveline can be connected is the maximum turn that should be made. Cutting Height Adjustment NOTICE Avoid ground contact with blades. Striking ground with blades produces one of the most damaging shock loads a cutter can encounter. If this occurs repeatedly, the cutter, driveline, and gearboxes will be damaged. Cutting height range is from 1" to 15". A hydraulic cylinder is used for cutting height adjustment. When selecting a cutting height, you should consider the area of operation. If the ground is rolling and has mounds the blades could contact, set the cutting height accordingly. The cutting height (blade edge) is approximately 1" above the bottom of the side skid. Cutting Height (Normal Mowing) - Center Section 1. Position the cutter on a hard level surface and select an approximate cutting height, Example 6". 2. Raise wings and lock them in the UP position. 3. Raise or lower the center section to obtain a distance of 5" from bottom edge of skid shoe to the ground. 4. Loosen jam nuts on the attitude rod that runs from the wheel yoke to the tongue. 5. Adjust rod in or out until the rear of the cutter is approximately 1/2" higher than the front. 6. Tighten jam nuts against sleeve. Cutting Height (Normal Mowing) - Wings 1. Lower wings to normal mowing position. 2. Loosen the jam nut on the adjustable link (turn buckle). 3. Lengthening the link will raise the wing, shortening the link will lower the wing. The rear edge of the wing should be parallel to the ground. Operation 15

16 When using the cutter to shred, the rear of the cutter deck should be approximately 1/2" to 1" lower than the front. TRACTOR OPERATION Use care when operating around tree limbs and other low objects. Avoid being knocked off tractor and being injured. Only use a tractor with a Roll Over Protection Structure (ROPS) and seat belt. Securely fasten seat belt. The cutter is operated with tractor controls. Engage the PTO at a low rpm to prevent excessive loads on the cutter drive system. Increase throttle to recommended PTO operating RPM. Be sure operator is familiar with all controls and can stop tractor and cutter quickly in an emergency. The operator should give complete, undivided attention to operating tractor and cutter. CUTTER OPERATION When beginning operation of the cutter, make sure that all persons are in a safe location. Power for operating the cutter is supplied by the tractor PTO. Operate PTO at 540 (1000 RPM for "Q" models). Know how to stop the tractor and cutter quickly in an emergency. Engage PTO at a low engine, rpm to minimize stress on the drive system and gearbox. With PTO engaged, raise PTO speed to 540 or 1000 RPM depending on model and maintain throughout cutting operation. Gearbox protection is provided by a slip clutch with replacement fiber disc. The slip clutch is designed to slip when excessive torsional loads occur. Move slowly into material. Adjust tractor ground speed to provide a clean cut without lugging the tractor engine. Use a slow ground speed for better shredding. Proper ground speed will depend on the terrain and the material s height, type, and density. Normally, ground speed will range from 2 to 5 mph. Tall, dense material should be cut at a low speed; thin, medium-height material can be cut at a faster ground speed. Always operate tractor PTO at proper RPM (540 or 1000 depending on model) to maintain blade speed and to produce a clean cut. Under certain conditions tractor tires may roll down some grass and prevent cutting at the same height as the surrounding area. When this occurs, reduce your ground speed but maintain PTO at 540 or 1000 RPM. The lower ground speed will permit grass to rebound partially. Mowing Tips Look down and to the rear and make sure area is clear before operating in reverse. Do not operate or transport on steep slopes. Do not stop, start, or change directions suddenly on slopes. Use extreme care and reduce ground speed on slopes and rough terrain. Watch for hidden hazards on the terrain during operation. Stop power unit and equipment immediately upon striking an obstruction. Turn off engine, remove key, inspect, and repair any damage before resuming operation. Maximum recommended ground speed for cutting or shredding is 6 miles per hour. Adjust tractor ground speed by using higher or lower gears to provide a clean cut without lugging tractor engine. Tall material should be cut twice. Cut material higher the first pass. Cut at desired height at 90 degrees the second pass. Remember, sharp blades produce cleaner cuts and use less power. Before entering an area, analyze it to determine the best procedure. Consider the height and type of material to be cut and the terrain type (hilly, level or rough, etc.). Shredding WARNING WARNING CAUTION The cutter may be used to shred various crops including green manure, straw, stubble, asparagus residue, corn stalks and similar crops in preparation for tilling. It may also be used to shred pruning in orchards, groves and vineyards. Each shredding operation may require a different setup. Start with front edge of cutter high. Adjust up or down as necessary with attitude rod. Experiment until you obtain the results you want. When shredding attitude is set, check that the distance from the bottom rear edge of the wing to the ground matches the bottom edge of the rear center section to the ground. 16 Operation MAN1237 (9/1/2017)

17 TRANSPORTING WARNING Power unit must be equipped with ROPS or ROPS cab and seat belt. Keep seat belt securely fastened. Falling off power unit can result in death from being run over or crushed. Keep foldable ROPS system in locked up position at all times. Always raise unit and install transport locks before transporting. Leak down or failure of mechanical or hydraulic system can cause equipment to drop. Always attach safety chain to tractor drawbar when transporting unit. Never exceed 20 mph (32.2 km/h) during transport. Never allow riders on power unit or attachment. Do not operate PTO during transport. Do not operate or transport on steep slopes. Do not operate or transport equipment while under the influence of alcohol or drugs. Figure 1. Transport Lock Pin Center Section Lock-Up 1. Raise cutter with hydraulic cylinder to maximum height. 2. Remove klik pin and lock pin from storage position (Figure 2). Always comply with all state and local lighting and marking requirements. Lock-Up CAUTION Always transport with wings and center frame in the raised, locked position. Wing Lock-Up 1. Raise wing to the up position. 2. Remove klik pin and lock pin from storage position. 3. Place lock pin in lock position and secure with klik pin. 4. Repeat steps 1 to 3 for opposite wing. 5. Lower cylinder against lock-up bars (Figure 1). Figure 2. Transport Lock Pin In Transport Position 3. Place lock pin and klik pin in lock position and lower cutter against lock pin. 4. To lower cutter for operation, extend hydraulic cylinder to raise cutter. Move lock pin from lock position to storage position (Figure 3). 5. Lower cutter to desired cutting height. Figure 3. Transport Lock Pin In Operation Position MAN1237 (9/1/2017) Operation 17

18 STORAGE Follow these steps when storing your cutter: 1. Clean cutter before storing. See page 23 for cleaning instructions. Store on level, solid ground. 2. Disconnect driveline and secure up off the ground. 3. Lower wings to ground. 4. Raise cutter center section and pin transport bar in raised position. 5. Attach parking jack and raise tongue weight off tractor drawbar. 6. Place wedge blocks at front and rear of wheels on center section and each wing to prevent wheel rotation. 7. Securely block all four corners of center section and each wing with jack stands. 8. Remove hydraulic hoses after tractor is turned off and all system pressure is released by operating valve levers several times. 9. Remove safety tow chain. 10. Remove retainer pin and high strength drawbar pin. 11. Keep children and bystanders away from storage area. PRE-OPERATION CHECK LIST (OWNER'S RESPONSIBILITY) Review and follow all safety rules and safety decal instructions on page 7 through page 13. Check that all safety decals are installed and in good condition. Replace if damaged. Check that equipment is properly and securely attached to tractor. the PTO slip joint is lubricated and that the gearbox fluid levels are correct. Set tractor PTO at correct rpm for your equipment. Lubricate all grease fitting locations. Make sure PTO shaft slip joint is lubricated. Check that all hydraulic hoses and fittings are in good condition and not leaking before starting tractor. Check that hoses are not twisted, bent sharply, kinked, frayed, or pulled tight. Replace any damaged hoses immediately. Check that all hardware is properly installed and secured. Check cutting height and attitude adjustment. Raise and lower equipment to make sure air is purged from hydraulic cylinders and hoses. Raise and lower equipment to make sure air is purged from hydraulic cylinders and hoses. Check that blades are sharp and secure and cutting edge is positioned to lead in a counterclockwise rotation for center and right wings, and clockwise for left wing. Make sure tractor ROPS or ROPS cab and seat belt are in good condition. Keep seat belt securely fastened during operation. Check that shields and guards are properly installed and in good condition. Replace if damaged. Before starting engine, operator must be in tractor seat with seat belt fastened. Place transmission in neutral or park, engage brake and disengage tractor PTO. Inspect area to be cut and remove stones, branches, or other hard objects that might be thrown and cause injury or damage. Make sure driveline spring-activated locking pin or collar slides freely and is seated firmly in tractor PTO spline groove. Check all lubrication points and grease as instructed in lubrication information. Make sure Inspect rubber or chain shielding and replace any damaged rubber shield or missing links. Make sure tractor 3-point lift links do not interfere with hydraulic hoses or driveline throughout full turning range. 18 Operation MAN1237 (9/1/2017)

19 OWNER SERVICE The information in this section is written for operators who possess basic mechanical skills. If you need help, your dealer has trained service technicians available. For your protection, read and follow the safety information in this manual. MAN1237 (9/1/2017) WARNING Keep all persons away from operator control area while performing adjustments, service, or maintenance. Before working underneath, disconnect driveline from tractor, lower wings to ground, raise cutter, and pin transport bar in raised position. Attach parking jack and lower to ground. Securely block all four corners of center section and each wing with jack stands. Blocking up prevents the cutter from dropping due to hydraulic leak down, hydraulic system failure, or mechanical component failure. Service and maintenance work not covered in OWNER SERVICE must be done by a qualified dealership. Special skills, tools, and safety procedures may be required. Failure to follow these instructions can result in serious injury or death. Before servicing, adjusting, repairing or unplugging, stop tractor engine, place all controls in neutral, set park brake, remove ignition key, and wait for all moving parts to stop. Never perform service or maintenance with engine running. CAUTION If you do not understand any part of this manual and need assistance, see your dealer. Always wear relatively tight and belted clothing to avoid entanglement in moving parts. Wear sturdy, rough-soled work shoes and protective equipment for eyes, hair, hands, hearing, and head; and respirator or filter mask where appropriate. BLOCKING METHOD To minimize the potential hazards of working underneath the cutter, follow these procedures: WARNING Before performing any service or maintenance, lower equipment to ground or block securely, turn off engine, remove key, and disconnect driveline from tractor PTO. Never go underneath equipment (lowered to the ground or raised) unless it is properly blocked and secured. Never place any part of the body underneath equipment or between moveable parts even when the engine has been turned off. Hydraulic system leak down, hydraulic system failures, mechanical failures, or movement of control levers can cause equipment to drop or rotate unexpectedly and cause severe injury or death. Follow Operator's Manual instructions for working underneath and blocking requirements or have work done by a qualified dealer. Do not position jackstands under wheels, axles, or wheel supports. Components can rotate and cause cutter to fall. 1. Jackstands with a load rating of 1000 lbs. or more are the only approved blocking device for this cutter. Install jackstands (shown by Xs in Figure 4) under the cutter before working underneath unit. 2. Consider the overall stability of the blocked unit. Just placing jackstands underneath will not ensure your safety. The working surface must be level and solid to support the weight on the jackstands. Make sure jackstands are stable, both top and bottom. Make sure cutter is approximately level. 3. With full cutter weight lowered onto jackstands, test blocking stability before working underneath. 4. If cutter is attached to tractor when blocking, set the brakes, remove key, and block cutter before working underneath. 5. Securely block rear tractor wheels, in front and behind. Owner Service 19

20 1. Driveline U-joint 10 Hours 2. Telescoping shaft 10 Hours 3. Clevis pivot 40 Hours 4. CV body assembly 10 hours (10 pumps minimum) 5. Driveline shield 10 Hours 6. Splined yoke 10 Hours 7. Gearbox (above lower Daily line on dipstick) 8. Tongue pivot (2) 40 Hours 9. Wheel yoke pivot (7) 40 Hours 10. Gearbox (bottom of Daily side hole) 11. Tailwheel spindle 20 Hours 12. Turnbuckle 40 Hours 13. Blade pin 40 Hours Figure 4. Jackstand Placement and Lubrication Points LUBRICATION Do not let excess grease collect on or around parts, particularly when operating in sandy areas. See Figure 4 for lubrication points and frequency or lubrication based on normal operating conditions. Severe or unusual conditions may require more frequent lubrication. Use a lithium grease of #2 consistency with a MOLY (molybdenum disulfide) additive for all locations unless otherwise noted. Be sure to clean fittings thoroughly before attaching grease gun. One good pump of most guns is sufficient when the lubrication schedule is followed. Gearbox Lubrication For gearbox, use a high quality gear oil with a viscosity index of 80W or 90W and an API service rating of GL 4 or 5 in gearboxes. Fill gearbox until oil is above lower line on dipstick. Check gearbox oil level daily for evidence of leakage, and contact your dealer if leakage occurs. Check vent plug periodically and clean if it does not relieve pressure. Driveline Lubrication 1. Lubricate the driveline slip joint every eight operating hours. Failure to maintain proper lubrication could result in damage to U-joints, gearbox, and driveline. 2. Lower cutter to ground, disconnect driveline from tractor PTO shaft, and slide halves apart but do not disconnect from each other. 3. Apply a bead of grease completely around male half where it meets female half. Slide drive halves over each other several times to distribute grease. 20 Owner Service MAN1237 (9/1/2017)

21 Seasonal Lubrication In addition to the daily recommended lubrication, a more extensive application is recommended seasonally. 1. Fill CV double yokes with 20 pumps of grease with the joints in a straight line. 2. Articulate CV body to maximum angle several times to ensure full coverage of joints. 3. Place joints in the straight position and a add 10 additional pumps of grease to both joints. 4. Wipe telescoping drive clean of all old grease and contaminants. 5. Add a thin layer of new grease over telescoping drive. BLADES Before working underneath, read manual instructions, securely block up, and check stability. Secure blocking prevents equipment from dropping due to hydraulic leak down, hydraulic system failure, or mechanical component failure. Blade Removal (Figure 5) MAN1237 (9/1/2017) WARNING 8. CROSSBAR ASSEMBLY 9. BLADE /2 BLADE PIN 11. SHIM 18 GA 12. SHIM 20 GA 13. 5/16 SPACER 14. KEYHOLE PLATE 15. BLADE IN LOCK CLIP 16. 1/2 NC X 1-1/4 HHCS GR5 Figure 5. Blade Assembly 1. Disconnect driveline from tractor PTO. 2. Raise cutter and block securely (see Figure 4). 3. Align crossbar (8) with blade access hole in the cutter frame. Remove cap screw (16), blade pin lock clip (15), keyhole plate (14), spacer (13), and shims (11 & 12). Carefully drive blade pin (10) out of crossbar. 4. Rotate crossbar and repeat for opposite blade. NOTICE If blade pin (10) is seized in crossbar and extreme force will be needed to remove it, support crossbar from below to prevent gearbox damage. Blade Installation (Figure 5) CAUTION Your dealer can supply genuine replacement blades. Substitute blades may not meet original equipment specifications and may be dangerous. NOTICE Crossbar rotation has clockwise rotation on left gearbox and counterclockwise rotation on the right and center gearboxes when looking down on cutter. Be sure to install blade cutting edge to lead in correct rotation. NOTE: Always replace or sharpen both blades at the same time. 1. Inspect blade pin (10) for nicks or gouges, and if you find any replace the blade pin. 2. Insert blade pin through the blade. Blade should swivel on blade pin; if it doesn t, determine the cause and correct. 3. Align crossbar (8) with blade access hole in cutter frame. Make sure blade offset is down away from cutter. 4. Insert blade pin (10) through blade. Push blade pin through crossbar. 5. Install shims (11 & 12) and spacer (13) over blade pin. NOTE: Only use enough shims to allow keyhole plate (14) to slide into blade pin groove. 6. Install blade clip (15) over keyhole plate and into blade pin groove. 7. Secure into position with cap screw (16). Torque cap screw to 85 lbs-ft. 8. Grease pin via zerk at end of pin. 9. Repeat steps for opposite side. NOTE: Blade should be snug but should swivel on pin without having to exert excessive force. Blade should not move more than a 1/4 inch up or down at the tip. Keep any spacers not used in the installation as replacements or for future installation. Owner Service 21

22 Blade Sharpening NOTICE When sharpening blades, grind the same amount on each blade to maintain balance. Replace blades in pairs. Unbalanced blades will cause excessive vibration, which can damage gearbox bearings. Vibration may also cause structural cracks to cutter. 1. Sharpen both blades at the same time to maintain balance. Follow original sharpening pattern. 2. Do not sharpen blade to a razor edge leave at least a 1/16" blunt edge. 3. Do not sharpen back side of blade. Figure 6. Blade Sharpening SLIP CLUTCH ADJUSTMENT (FIGURE 7) The slip clutch is designed to slip so that the gearbox and driveline are protected if the cutter strikes an obstruction. A new slip clutch or one that has been in storage over the winter may seize. Before operating the cutter, make sure it will slip by performing the following operation: 1. Turn off tractor engine and remove key. 2. Remove driveline from tractor PTO. 3. Loosen six 10 mm cap screws (6) to remove all tension from Belleville spring plate (5). 4. Hold clutch hub (3) solid and turn shaft to make sure clutch slips. 5. If clutch does not slip freely, disassemble and clean the thrust plate faces (4), flange yoke (1), and clutch hub (3). 6. Reassemble clutch. 7. Tighten Belleville spring (5) until it is against the thrust plate (4) of the clutch, and then back off each of the six nuts by 2 full revolutions. The gap between Belleville spring and thrust plate should be 1/8" as shown in Figure If a clutch continues to slip when the spring is compressed to 1/8" gap, check friction discs (2) for excessive wear. Discs are 1/8" when new. Replace discs after 1/16" wear. Minimum disc thickness is 1/16". 1. Flange yoke 2. Friction disc 3. Hub 1-3/8 round bore 4. Thrust plate 5. Belleville spring plate mm x 1.5P x 50 mm Cap screw mm x 1.5P Hex nut mm x 1.5P x 65 mm Cap screw mm x 1.5P Hex nut Figure 7Slip Clutch Assembly 22 Owner Service MAN1237 (9/1/2017)

23 SHIELDING REPAIR DANGER Full chain shielding must be installed at all times. Thrown objects could injure people or damage property. If the machine is not equipped with full chain shielding, operation must be stopped. This shielding is designed to reduce the risk of thrown objects. The mower deck and protective devices cannot prevent all objects from escaping the blade enclosure in every mowing condition. It is possible for objects to ricochet and escape, traveling as much as 300 feet (92m). Repairing Chain Shielding 1. Inspect chain shielding each day of operation and replace any broken or missing chains as required. 2. Replace any missing hardware. SERVICING TIRES SAFELY Used Aircraft Tires (Figure 8) WARNING A CLEANING After Each Use PN Figure 8. Split Rim Tire Servicing Remove large debris such as clumps of dirt, grass, crop residue, etc. from machine. Inspect machine and replace worn or damaged parts. Replace any safety decals that are missing or not readable. Periodically or Before Extended Storage Clean large debris such as clumps of dirt, grass, crop residue, etc. from machine. Remove the remainder using a low-pressure water spray. Do not attempt to mount a tire unless you have the proper equipment and experience to perform the job. Always maintain the correct tire pressure. Do not inflate tires above the recommended pressure. Never weld or heat a wheel and tire assembly. The heat can cause an increase in air pressure and result in a tire explosion. Welding can structurally weaken or deform the wheel. When inflating tires, use a clip-on chuck and an extension hose long enough to allow you to stand to the side not in front of or over the tire assembly. Use a safety cage if available. Check wheels for low pressure, cuts, bubbles, damaged rims, or missing lug bolts and nuts. Never remove split rim assembly hardware (A) with the tire inflated. MAN1237 (9/1/2017) 1. Be careful when spraying near scratched or torn safety decals or near edges of decals as water spray can peel decal off surface. 2. Be careful when spraying near chipped or scratched paint as water spray can lift paint. 3. If a pressure washer is used, follow the advice of the pressure washer manufacturer. Inspect machine and replace worn or damaged parts. Sand down scratches and the edges of areas of missing paint and coat with Woods spray paint of matching color (purchase from your Woods dealer). Replace any safety decals that are missing or not readable (supplied free by your Woods dealer). See Safety Decals section for location drawing. Owner Service 23

24 TROUBLESHOOTING PROBLEM POSSIBLE CAUSE SOLUTION Does not cut Dull blades Sharpen blades. Worn or broken blades Incorrect PTO speed Ground speed too fast Drive not functioning (blades do not turn when PTO is running) Gearbox malfunction Excessive clutch slippage Incorrect blade direction Replace blades. (Replace in pairs only.) Set at rated PTO speed. Reduce ground speed. Check drive shaft connection. Check gearbox. Repair gearbox. Adjust clutch. Check to be sure blade edge is correct for direction of rotation. Streaks or ragged cut Broken or worn blades Replace or sharpen blades. Excessive side skid wear Attitude incorrect Ground speed too fast Excessive cutting height Excessive lush and tall vegetation Running with skids continuously on ground Level machine. Reduce ground speed. Lower cutting height. (Note: Set height so blades do not frequently hit ground.) Recut at 90 to first pass. Raise cutting height or adjust. Excessive clutch slippage Clutch out of adjustment Adjust clutch. Clutch discs worn; wear stops contacting opposite plate Blades hitting ground Replace discs. Raise cutting height. Vibration Broken blade Replace blades in pairs. Bearing failure Hitch length incorrect Universal drive Check gearbox shafts for side play. Reset hitch length. Adjust pedestal bearing height to be parallel to ground. Blades hitting deck Bent blades or crossbar Replace bent blades or crossbar. Unit will not raise Low oil Add hydraulic oil. Unit doesn t cut level Wing section cuts lower than center Wing section cuts higher than center Lengthen turnbuckle connecting center yoke to wing wheel yoke. Shorten turnbuckle connecting center yoke to wing wheel yoke. 24 Troubleshooting MAN1237 (9/1/2017)

25 DEALER SERVICE The information in this section is written for dealer service personnel. The repair described here requires special skills and tools. If your shop is not properly equipped or your mechanics are not properly trained in this type of repair, you may be time and money ahead to replace complete assemblies. WARNING Before working underneath, read manual instructions, securely block up, and check stability. Secure blocking prevents equipment from dropping due to hydraulic leak down, hydraulic system failure, or mechanical component failure. Keep all persons away from operator control area while performing adjustments, service, or maintenance. CAUTION Always wear relatively tight and belted clothing to avoid getting caught in moving parts. Wear sturdy, rough-soled work shoes and protective equipment for eyes, hair, hands, hearing, and head; and respirator or filter mask where appropriate. GEARBOX MAINTENANCE NOTE: Read this entire section before starting any repair. Many steps are dependent on each other. 1. Fill gearbox with SAE 80W or 90W gear lube. Proper oil level is between lowest ring and end of dipstick. Seal Replacement (Figure 12) Recommended sealant for gearbox repair is Permatex Aviation 3D Form-A-Gasket or equivalent. Leakage can occur at the vertical or horizontal gaskets and shaft seals. Leakage at the horizontal gasket or seal can be repaired without removing the gearbox from the cutter. Seal Installation NOTE: Proper seal installation is important. An improperly installed seal will leak. 1. Clean area in housing where seal outer diameter (OD) seats. Apply a thin coat of Permatex. 2. Inspect area of shaft where seal seats. Remove any burrs or nicks with an emery cloth. 3. Lubricate gear shaft and seal lips. 4. Place seal squarely on housing, spring-loaded lip toward housing. Select a piece of pipe or tubing with an OD that will sit on the outside edge of the seal but will clear the housing. Tubing with an OD that is too small will bow seal cage and ruin seal. 5. Carefully press seal into housing, avoiding distortion to the metal seal cage. 1. Seal 2. Pipe or tube 3. Seal seat 4. Casting Pipe or tube must press at outer edge of seal. NOTE: Repair to this gearbox is limited to replacing bearings, seals, and gaskets. Replacing gears, shafts, and a housing is not cost effective. Purchasing a complete gearbox is more economical. 2. Inspect gearbox for leakage and bad bearings. Leakage is a very serious problem and must be corrected immediately. NOTE: Bearing failure is indicated by excessive noise and side-to-side or end-play in gear shafts. MAN1237 (9/1/2017) Incorrect Installation Figure 12. Seal Installation Dealer Service 25

26 Vertical Shaft Seal Replacement (Figure 13) 1. Disconnect and remove the rear driveline from the gearbox. 2. Remove drain plug and drain gear lube from housing. Replace plug when empty. 3. Remove crossbar (see page 30). 4. Remove protective seal (8) and vertical shaft seal (18). Replace seal (18) with new seal. Vertical seal should be recessed in housing. Horizontal seal (19) should be pressed flush with outside of housing. NOTE: Distortion to seal cage or damage to seal lip will cause seal to leak. 5. Fill gearbox with SAE 80W or 90W gear lube until it runs out the level plug. 6. Remove and replace any seal damaged in installation. Horizontal Shaft Seal Replacement (Figure 13) 1. Disconnect and remove the rear driveline from the gearbox. 2. Remove drain plug and drain gear lube from housing. Replace plug when empty. 3. If the leak occurred at either end of horizontal shaft, remove oil cap (20) and/or oil seal (19). Replace with new one. 4. Fill gearbox with SAE 80W or 90W gear lube to proper level. GEARBOX REPAIR Removal from Cutter (Figure 13) NOTE: Gearbox is heavy: do not attempt to move without mechanical assistance. 1. Disconnect and remove the rear driveline from the gearbox. 2. Remove cotter pin and nut from vertical shaft and remove crossbar (see page 30). 3. Remove the six bolts that attach gearbox to cutter and remove gearbox. Disassembly (Figure 13) 1. Remove top cover (22) from gearbox and pour out gear oil. 2. Remove oil cap (20) (to be replaced). 3. Remove snap ring (10) and shim (13) from input shaft (3). 4. Support gearbox in hand press and push on input shaft (3) to remove bearing (7). 5. Remove six cap screws (23) and top cover (22) from housing. Remove gear (1) from inside housing. 6. Remove oil seal (19) from front of housing (to be replaced). 7. Remove snap ring (10) and shim (13) from front of housing (2). 8. Remove input bearing (7) by using a punch and hammer from outside of housing. 9. Support housing in vise in a horizontal position. 10. The castle nut (15), cotter pin (25), and hub are already removed with the stump jumper/crossbar. Remove the protective seal (8), and oil seal (18). 11. Remove cotter pin (9), castle nut (14), and shim (17) from output shaft (4). 12. Remove output shaft (4) by using a punch and hammer and tap on top to drive down. Remove gear (5) and shim (16) from inside housing. 13. Remove bottom bearing (26) by using a punch and hammer from the top, outside the housing. 14. Support housing upside down (top cover surface) and remove bottom bearing (6) by using a punch and hammer from the bottom side of the housing. 15. Inspect gears for broken teeth and wear. Some wear is normal and will show on loaded side. Forged gear surfaces are rough when new. Check that wear pattern is smooth. 16. Inspect vertical and horizontal shafts for grooves, nicks, or bumps in the areas where the seals seat. Resurface any damage with emery cloth. 17. Inspect housing and caps for cracks or other damage. Assembly (Figure 13) 1. Clean housing, paying specific attention to areas where gaskets will be installed. 2. Wash housing and all components thoroughly. Select a clean area for gearbox assembly. Replace all seals, bearings, and gaskets. All parts must be clean and lightly oiled before reassembling. 3. Insert both output bearings (6) in the housing, using a round tube of the correct diameter and a hand press. 4. Slide output shaft (4) through both bearings (6) until it rests against top bearing (6). 5. Slide shim (16) over output shaft (4). 6. Press gear (5) onto output shaft (4) and secure with shim (17), castle nut (14), and cotter pin (9). 7. Apply grease to lower seal lips (18) and press seal (18) over output shaft (4), using a tube of the 26 Dealer Service MAN1237 (9/1/2017)

27 correct diameter. Be sure not to damage the seal lip. 8. Press in housing so that seal is recessed. Press protective seal (8) until seated flush with housing. Verify that the seal (8) is seated correctly. 9. Press bearing (7) into the housing, using a round tube of the correct diameter and a hand press. Secure with shim (13) and snap ring (10). 10. Secure snap ring (11) on input shaft (3) if not already secure. 11. Place gear (1) through top of housing and align gear (1) and gear (5) so that gear teeth are a match. 12. While holding gear (1) in place, slide input shaft (3) through gear (1) and bearing (7). Align splines on shaft (3) and gear (1). 13. Slide shim (12) over input shaft (3) and press bearing (7) onto input shaft (3), using a round tube of the correct diameter and a hand press. 14. Slide shim (13) over input shaft (3) and secure with snap ring (10). 15. Check input shaft end float by moving the input shaft (3) by hand. If end float is higher than 0.012", insert shim between input shaft (3) and rear bearing (7). Repeat until end float is less than 0.012". Check rotational torque by hand. The torque should be less than 2.2 lbs-inch. 16. Check that the gear backlash is between 0.006" and 0.016". You should not have to adjust the backlash. 17. Press in input oil seal (19), using tube of correct diameter. Be careful not to damage seal lip. 18. Press oil cap (20) on to cover the rear of housing, using a tube of the correct diameter. 19. Place top cover (22) on top of housing and secure with six cap screw (23). 20. Check gearbox housing for leaks by plugging all holes except one. Apply 4 psi compressed air and immerse the gearbox in water to verify that there are no leaks. 21. Remove gearbox from water and dry off with compressed air. Add SAE 80W or 90W EP oil to proper level. Tighten all plugs. Reinstallation NOTE: Gearbox is heavy: do not attempt to move without mechanical assistance. 1. Set gearbox on cutter and fasten with bolts and nuts. Torque bolts to 300 lbs-ft. 2. Attach crossbar (Crossbar Installation, page 31). 1. Crown gear 2. Gearbox housing 3. Input shaft 4. Output shaft 5. Gear pinion 6. Bearing 7. Input bearing 8. Protective seal 9. Cotter pin 10. Snap ring 11. Snap ring 12. Shim, 45.3 x Shim, 70.3 x Nut 15. Castle nut 16. Shim, 50.3 x Shim 18. Oil seal (Vertical Shaft) 19. Oil seal (Horizontal Shaft) 20. Cap 22. Top cover 23.Cap screw 8mm x 16 (8.8) 24. Dip Stick 25. Cotter Pin 26. Washer Figure 13. Gearbox MAN1237 (9/1/2017) Dealer Service 27

28 SPLITTER GEARBOX REPAIR (Figure 14) Removal from Cutter 1. Disconnect and remove all drivelines from gearbox. 2. Remove the four cap screw and lock washers that secure gearbox to cutter, and remove gearbox. NOTE: Gearbox is heavy: do not attempt to move it without mechanical assistance. Disassembly Center Shaft 1. Remove plug from side of gearbox and pour out the gear oil. 2. Remove seal (11, to be replaced) from the front and rear of the center shaft (14). 3. Remove snap ring (10) and shim (12) from the front and rear of the center shaft (14). 4. Support gearbox in a hand press and push on the rear of the center shaft. 5. Remove bearing (13) from center shaft (14). 6. Remove six cap screws (20) and top cover (21) from the gearbox housing. 7. Remove gear (17) and bearing (16). 8. Snap ring (15) does not have to be removed from shaft (14) unless it is damaged. Side Shaft 9. Remove seal (2, to be replaced) from the output shaft (1). 10. Remove snap ring (4) and shim (8) from output shaft (1). 11. Support gearbox in hand press. Using a punch through the front opening of the gearbox and, push shaft (1) and bearing (5) out the backside of housing. 12. Remove gear (6) from inside housing. 13. Remove bearing (7) and shim (8) by using a hammer and punch through front opening of the gearbox and force them out the backside of the housing. 14. Repeat steps 7 through 11 for opposite side shaft. Inspect Components 15. Inspect gears for broken teeth and wear. Some wear is normal and will show on the loaded side of the teeth. Forged gear surfaces are rough when new. Check that wear pattern is smooth. 16. Inspect shafts for grooves, nicks, or bumps in the areas where seals seat. Resurface any damage with emery cloth or replace shaft. 17. Inspect housing and caps for cracks or other damage. Assembly 1. Clean housing, pay specific attention to areas where gaskets are installed. 2. Wash housing and all components thoroughly. 3. Select a clean work area to assemble gearbox. 4. Replace all seals, bearings, and gaskets. 5. All parts must be clean and lightly oiled before assembly. Side Shaft 6. Insert bearing (7) and shim (8) in housing using a round tube of the same size diameter and a hand press. 7. Place gear (6) inside the housing and slide output shaft (1) through gear (6) and into bearing (7). 8. Slide bearing (5) and shim (8) over output shaft. Secure with snap ring (4). 9. Check end play of shaft by moving it in and out. If end play is more than 0.012", insert another shim (8) between snap ring and bearing. Repeat process until end play is less than 0.012". 10. Check rotational torque. Torque should be less than 2.2 lbs-inch gear. 11. Place seal (2) over shaft and press into housing using a tube of the same diameter. Seal should be flush with housing when properly installed. 12. Repeat steps 6 through 10 for opposite side shaft. Center Shaft 13. Place gear (17) inside housing and slide center shaft (14) through the gear from the front of the housing. 14. Slide bearings (16 & 13) and shims (12) over each end of the center shaft (14). Secure bearings into position using snap rings (10). 15. Check end play of shaft by moving it in and out. If end play is more than 0.012", insert another shim (12) between snap ring and bearing. Repeat process until end play is less than 0.012". 16. Check rotational torque. Torque should be less than 2.2 lbs-inch gear. 17. Check gear backlash, backlash should be between 0.006" and 0.016". You should not have to adjust for backlash. 18. Place seal (11) over shaft and press into housing using a tube of the same diameter. Seal should be flush with housing when properly installed. Repeat process for opposite end shaft. 28 Dealer Service MAN1237 (9/1/2017)

29 Check Gearbox 1. Place top cover (21) on housing and secure into position using six cap screws (20). 2. Check gearbox for leaks by: plugging all holes except one, applying 4 psi of compressed air, and immersing gearbox in water. Verify gearbox does not leak. NOTE: Excessive air pressure will damage seals. 3. Remove gearbox from water and dry off. 4. Remove upper plug (3) on right side of housing. Add SAE 80W or 90W EP oil until it runs out side level hole. Replace plug. 5. Install breather (18) in top cover. Reinstallation on Cutter NOTE: Gearbox is heavy: do not attempt to move it without mechanical assistance. 1. Place gearbox on cutter and secure into position using four cap screws and lock washers. 2. Torque hardware to 300 lbs-ft. 3. Attach all drivelines to gearbox. 4. Install all shields. 1. Shaft 1-3/4, 20 spline, wing 2. Oil seal 3. 3/8 plug 4. Snap ring 5. Bearing 6. Pinion gear 7. Bearing 8. Shim 9. Housing 10. Snap ring 11. Oil seal 12. Shim 13. Bearing 14. Shaft 1-3/4, 20 spline, center 15. Snap ring 16. Bearing 17. Gear 18. 1/2 Breather 19. 5/16 Lock washer 20. M8 x 30 Cap screw Cover 22. Snap ring Figure 14. Splitter Gearbox Assembly MAN1237 (9/1/2017) Dealer Service 29

30 CROSSBAR REMOVAL 1. It is necessary to gain access to bottom side of cutter for crossbar removal. See Blocking Method page 19. NOTE: You will need to use either the puller screw (Item 6, Figure 16) or a small hydraulic jack to remove the crossbar. 2. Remove blades from crossbar as shown in Figure CROSSBAR ASSEMBLY 9. BLADE /2 BLADE PIN 11. SHIM 18 GA 12. SHIM 20 GA 13. 5/16 SPACER 14. KEYHOLE PLATE 15. BLADE IN LOCK CLIP 16. 1/2 NC X 1-1/4 HHCS GR5 Figure 15. Blade Removal 3. Refer to Figure 16. Remove cotter pin from bottom of crossbar and remove nut and washer. 4. Attach a clevis (1) to each end of crossbar, using blade pins, spacers, keyhole plates, and blade pin clips. 5. Position tube assembly (5) with threaded nut (4) toward crossbar for puller screw removal or down for hydraulic jack removal. 6. For removal with puller screw, attach tube (5) to each clevis with bolts (2) and nuts (3). Place pad (4) in nut and thread puller screw (6) into nut from bottom. Tighten until pad is solid against gearbox shaft. For best results, strike head of puller screw with a hammer while tightening with a wrench. 7. For removal with a jack, attach tube to each clevis with puller links (7), bolts (2), and nuts (3). Place jack on tube with end of jack pressing against gearbox shaft. Slowly apply force with jack. NOTE: Hydraulic jack will not operate if tipped more than 90. Use care to prevent bending crossbar during removal. 1. Crossbar puller clevis 2. 5/8 NC x 4-1/2 HHCS 3. 5/8 NC Hex nut 4. Crossbar puller pad 5. Crossbar puller tube 6. Crossbar puller screw 7. Crossbar puller link Figure 16. Crossbar Removal 30 Dealer Service MAN1237 (9/1/2017)

31 CROSSBAR INSTALLATION 1. Using emery cloth (220 or finer), remove surface rust, Loctite and foreign material from hub, splined gearbox vertical shaft, and crossbar assembly. 2. Slide crossbar assembly (10) onto splined shaft. Install washer (71) and nut (72) and align a slot with hole in splined shaft. Torque nut to 450 lbs-ft. 3. Install cotter pin (73) through slot in nut and bend ends over. Figure With snap rings removed, support drive in vise, hold yoke in hand and tap on yoke to drive cup up out of yoke. See Figure Crossbar assembly 71. Washer, 1.22 x x Castle nut, M30 x 2.0P 73. Cotter pin, 1/4 x 2-1/4 Figure 17. Crossbar Assembly Installation UNIVERSAL JOINT REPAIR 1. Yoke 2. Cup and bearings 3. Snap ring 4. Journal cross Figure Clamp cup in vise as shown in Figure 21 and tap on yoke to completely remove cup from yoke. Repeat step 2 and step 3 for opposite cup. Figure 18. U-Joint Exploded View U-Joint Disassembly 1. Remove external snap rings from yokes in four locations as shown in Figure 19. MAN1237 (9/1/2017) Figure 21 Dealer Service 31

32 4. Place universal cross in vise as shown in Figure 22 and tap on yoke to remove cup. Repeat Step 3 for final removal. Drive remaining cup out with a drift and hammer. SERVICING TIRES SAFELY Used Aircraft Tires (Figure 23) WARNING Do not attempt to mount a tire unless you have the proper equipment and experience to perform the job. U-Joint Assembly Figure Place seals securely on bearing cups. Insert cup into yoke from outside and press in with hand pressure as far as possible. Insert journal cross into bearing cup with grease fitting away from shaft. Be careful not to disturb needle bearings. Insert another bearing cup directly across from first cup and press in as far as possible with hand pressure. Always maintain the correct tire pressure. Do not inflate tires above the recommended pressure. Never weld or heat a wheel and tire assembly. The heat can cause an increase in air pressure and result in a tire explosion. Welding can structurally weaken or deform the wheel. When inflating tires, use a clip-on chuck and an extension hose long enough to allow you to stand to the side not in front of or over the tire assembly. Use a safety cage if available. Check wheels for low pressure, cuts, bubbles, damaged rims, or missing lug bolts and nuts. Never remove split rim assembly hardware (A) with the tire inflated. 2. Trap cups in vise and apply pressure. Be sure journal cross is started into bearings and continue pressure with vise, squeezing in as far as possible. Tapping the yoke will help. 3. Seat cups by placing a drift or socket (slightly smaller than the cup) on cup and rap with a hammer. Install snap ring and repeat on opposite cup. A 4. Repeat Step 1 and Step 2 to install remaining cups in remaining yoke. 5. Move both yokes in all directions to check for free movement. If movement is restricted, rap on yokes sharply with a hammer to relieve any tension. Repeat until both yokes move in all directions without restriction. PN Figure 23. Split Rim Tire Servicing 32 Dealer Service MAN1237 (9/1/2017)

33 DEALER SET-UP INSTRUCTIONS ASSEMBLY INSTRUCTIONS Assembly of this cutter is the responsibility of the WOODS dealer. It should be delivered to the owner completely assembled, lubricated and adjusted for normal cutting conditions. The cutter is shipped partially assembled. Assembly will be easier if components are aligned and loosely assembled before tightening hardware. Recommended torque values for hardware are located on page 63. Attitude Rod Length Small Aircraft Tires Beyond Nuts (34) Tongue at 11" 3.5 Tongue at 18" 1.75 Large Aircraft Tires Tongue at 11" 4.5 Tongue at 18" 2.5 Select a suitable working area. A smooth hard surface, such as concrete, will make assembly much quicker. Open parts boxes and lay out parts and hardware to make location easy. Refer to illustrations, accompanying text, parts lists and exploded view drawings. Install Wheel Complete the check list on page 35 when assembly is complete and cutter is delivered to the customer. Before working underneath, carefully read Operator s Manual instructions, disconnect driveline, raise mower, securely block up all corners with jackstands, and check stability. Secure blocking prevents equipment from dropping due to hydraulic leak down, hydraulic system failures, or mechanical component failures. Do not disconnect hydraulic lines until machine is securely blocked or placed in lowest position and system pressure is released by operating valve levers. Always wear relatively tight and belted clothing to avoid entanglement in moving parts. Wear sturdy, rough-soled work shoes and protective equipment for eyes, hair, hands, hearing, and head; and respirator or filter mask where appropriate. MAN1237 (9/1/2017) WARNING CAUTION Figure 24. Center Section Wheel and Hub Installation Install Wing Wheel(Figure 25) 1. Center Wheel Yoke Arm 83. 1/2" NC x 3" HHCS GR /2" NC Flange Lock Nut 1. Insert wheel hub into wing wheel yoke arms (5) and align holes. 2. Secure into position using cap screw (83) and flanged lock nut (88). 3. Attach wheel to hub using five lug nuts. Install the chamfered side of the lug nut toward the inside for steel rim for pneumatic tires and rims. Tighten to 75 lbs-ft. Check that tire air pressure is a maximum of 40 psi. NOTE: Install the flat side of the nut toward the inside for solid tires and aircraft tires (shown). 4. Install optional dual wheel and hub to inside of wheel yoke arm. Assembly 33

34 NOTE: Pneumatic (BW15.50 and BW15.50Q only), notat, and airplane tires are available for this cutter. See page 51 for parts list. Winch Kit Installation (Optional) Refer to page 59 for Installation and Operation instructions. 5. Wing wheel yoke arm, right 58. Wheel and hub 83. 1/2 NC x 3 HHCS GR /2 NC Flanged lock nut Figure 25. Wing Wheel - Right 34 Assembly MAN1237 (9/1/2017)

35 DEALER CHECK LISTS PRE-DELIVERY CHECK LIST (DEALER S RESPONSIBILITY) Inspect the equipment thoroughly after assembly to ensure it is set up properly before delivering it to the customer. The following check lists are a reminder of points to inspect. Check off each item as it is found satisfactory or after proper adjustment is made. Check that all safety decals are installed and in good condition. Replace if damaged. Check that shields and guards are properly installed and in good condition. Replace if damaged. Check all bolts to be sure they are properly torqued. Check wheel bolts for proper torque. Check that all cotter pins and safety pins are properly installed. Replace if damaged. Check that blades have been properly installed. Check and grease all lubrication points as identified in lubrication information on page 20. Check the level of gearbox fluids before delivery. Service, if required, as specified in the lubrication information on page 20. DELIVERY CHECK LIST (DEALER S RESPONSIBILITY) Show customer how to make adjustments and select proper PTO speed. Show customer how to make sure driveline is properly installed and that spring-activated locking pin or collar slides freely and is seated in groove on tractor PTO shaft. Show customer how to determine the turning limits of the CV PTO driveline. Show customer the safe, proper procedures to be used when mounting, dismounting, and storing equipment. Make customer aware of optional equipment available so that customer can make proper choices as required. Instruct customer how to lubricate and explain importance of lubrication. Point out the safety decals. Explain their meaning and the need to keep them in place and in good condition. Emphasize the increased safety hazards when instructions are not followed. Explain to customer that when transporting the cutter, the wing and center sections should be raised and their respective transport bars installed and pinned in place. Present Operator's Manual and request that customer and all operators read it before operating equipment. Point out the manual safety rules, explain their meanings and emphasize the increased safety hazards that exist when safety rules are not followed. Explain to customer the potential crushing hazards of going underneath raised equipment. Instruct that before going underneath to disconnect the driveline, securely block up all corners with jack stands and to follow all instructions in the BLOCKING METHOD, page 19 of the operator s manual. Explain that blocking up prevents equipment dropping from hydraulic leak down, hydraulic system failures or mechanical component failures. Point out all guards and shields. Explain their importance and the safety hazards that exist when not kept in place and in good condition. Explain to customer that when towing on a public road to comply with all state and local lighting/marking laws and to use a safety tow chain. MAN1237 (9/1/2017) Dealer Check Lists 35

36 NOTES 36 Notes MAN1237 (9/1/2017)

37 PARTS INDEX BATWING Rotary Cutter BW15.50, BW15.50Q BW10.50, BW10.50Q CENTER FRAME ASSEMBLY HYDRAULIC SYSTEM CENTER WHEEL YOKE ASSEMBLY WING ASSEMBLY TONGUE ASSEMBLY SPLITTER GEARBOX ASSEMBLY WING & CENTER GEARBOX ASSEMBLY DRIVE ASSEMBLY 540 RPM & 1000 RPM CV DRIVE CENTER DECK DRIVE WING DRIVE WHEEL & TIRE ASSEMBLY 5-BOLT LIGHT KIT ASSEMBLY CHAIN SHIELDING - REAR CHAIN SHIELDING - FRONT HYDRAULIC CYLINDERS HYDRAULIC CYLINDER STROKE CONTROL KIT CROSSBAR PULLER (OPTIONAL) BW10.50 / BW10.50Q COUNTERWEIGHT BOX ASSEMBLY (OPTIONAL) WINCH KIT (OPTIONAL) MAN1237 (9/1/2017) Parts 37

38 CENTER FRAME ASSEMBLY REF PART QTY DESCRIPTION Splitter gearbox RPM (see page 45) -OR Splitter gearbox RPM (see page 45) Gearbox RPM (see page 47) -OR Gearbox RPM (see page 47) Driveline complete, 2400, w/clutch (see page 50) RP 1 Splitter gearbox shield RP 1 Input drive shield Front skid, right Front skid, left (not shown) RP 1 Crossbar assembly KT 1 Blade kit, CCW RP 2 1-1/2 Blade pin Shim, 18 GA, 1-1/2 blade pin Shim, 20 GA, 1-1/2 blade pin Spacer, 5/16 thick Keyhole plate - special Blade pin lock clip - special * 2 1/2 NC x 1-1/2 HHCS, GR Washer, 1.22 x x M30 x 2.0P Castle nut REF PART QTY DESCRIPTION * 1 1/4 x 2-1/4 Cotter pin Access hole cover Manual tube /8 NC x 1-3/4 HFS, GR * 4 5/8 NC Flanged lock nut /4 NC x 3-1/2 HFS, GR /4 NC Flanged lock nut /2 NC x 1-3/4 HFS, GR * 8 1/2 NC Flanged lock nut 28 N/S * 3 5/16 NC x 1 Hex whiz bolt, GR M8-1.25P x 16 mm HFS, CL x.977 x 3.14 Magnet x.565 Aluminum rivet Hinge Pin Pin Transport Lock Lynch pin with chain /4 x 1-1/2 spring pin Complete decal set English safety decal set Spanish safety decal set N/S Not Serviced * Standard Hardware, Obtain Locally HHCS Hex Head Cap Screw HFS Hex Flange Screw (Rev. 12/11/2017) 38 Parts MAN1237 (9/1/2017)

39 CYLINDER ASSEMBLY REF PART QTY DESCRIPTION RP 2 WING LOCK (FOR CYLINDER PG. 58) 1A RP 2 WING LOCK (FOR CYLINDER PG. 57) PIN.75 X PIN 1.00 X WASHER 1" HYDRAULIC CYLINDER 3-1/2 X /2 NPT VENT PLUG 10 W ADAPTER 1/4 NPTF 1/2 NPTM /4 X 1/4 90 EL 1/16 RESTRICTOR HOSE.25 ID X.25 NPT X HOSE.25 ID X.25 NPT X MALE HYDRAULIC COUPLER LYNCH PIN W/ CHAIN REF PART QTY DESCRIPTION /4 X 1-1/2 COTTER PIN BOLT X CLAMP.50 DIA STEEL CUSHION CYLINDER, 3.0 X 1.25 X 10.0 NPT8 22A CYLINDER, 3.0 X 1.25 X 10.0 NPT RP 2 ATTITUTE ROD, RP 2 HOSE COVER CHANNEL NUT, HFN 5/16 NC, DRI-LOC PATCH FEEDLINE CLAMP - 1/ WASHER 3/4 SAE FLAT HRDN PIPE 3/4 X NUT HEX 3/4 NC PLTD WASHER 3/4" PIN 1.0 X 2.50 (Rev. 11/7/2017) MAN1237 (9/1/2017) Parts 39

40 CENTER WHEEL YOKE ASSEMBLY REF PART QTY DESCRIPTION RP 1 Wheel yoke, center RP 1 Wheel yoke, right RP 1 Wheel yoke, left RP 2 Spring link Spring, comp 3.25 x.56 x 7.3 x Adjustable link SMV Emblem Tire & hub (see page 51) x 4.31 Pin x 3.84 Pin x 2.50 Pin REF PART QTY DESCRIPTION * 4 1/2 NC x 3 HHCS, GR * 4 1/2 NC Flanged lock nut * 11 3/8 NC x 1 Carriage bolt, GR * 11 3/8 NC Flanged lock nut * 2 1/4 NC x 1 Button head screw, GR5 17 W70065 * 2 1/4 NC Whiz nut * 2 1/4 x 1-1/2 Cotter pin * 10 1/4-28 Straight grease fitting * Standard Hardware, Obtain Locally HHCS Hex Head Cap Screw (Rev. 11/7/2017) 40 Parts MAN1237 (9/1/2017)

41 WING ASSEMBLY REF PART QTY DESCRIPTION Gearbox, Right wing (see page 47) -or Gearbox, Left wing (see page 47) RP 1 Clutch shield, hinged RP 1 Skid, Right wing -or RP 1 Skid, Left wing RP 1 Crossbar assembly KT 1 Blade kit, CCW (Right wing) -or KT 1 Blade kit, CW (Left wing) RP 2 1-1/2 Blade pin Shim, 18 GA, 1-1/2 blade pin Shim, 20 GA, 1-1/2 blade pin Spacer, 5/16 thick Keyhole plate - special Blade pin lock clip - special (Rev. 11/7/2017) MAN1237 (9/1/2017) REF PART QTY DESCRIPTION * 2 1/2 NC x 1-1/2 HHCS, GR Washer, 1.22 x x M30 x 2.0P Castle nut * 1 1/4 x 2-1/4 Cotter pin /2 NC x 1-1/4 HFS, GR * 4 1/2 NC Flanged lock nut /4 NC x 3-1/2 HFS, GR /4 NC Flanged lock nut M8-1.25P x 16 mm HFS, CL x.977 x 3.14 Magnet x.565 Aluminum rivet * Standard Hardware, Obtain Locally HHCS Hex Head Cap Screw HFS Hex Flange Screw Parts 41

42 TONGUE ASSEMBLY (Rev. 11/7/2017) 42 Parts MAN1237 (9/1/2017)

43 TONGUE ASSEMBLY REF PART QTY DESCRIPTION * 2 HHCS 1/2 NC X 3-1/2 GR5 ZP * 1 HHCS 3/4 NC X 1-1/2 GR5 ZP SLV 3/4 X 1 X 9/16 HT * 2 3/4 NC X 2-1/4 HHCS, GR SAFETY CHAIN ASY 6400LB WSHR 3/4ID 1-1/2OD 1/4THICK SWIVEL PARKING JACK * 1 1/4 X 1-3/4 KLIK PIN * 4 HHCS.312 NC X 3/4 FLANGE ROLLER 2 X RP 1 WA, TONGUE HITCH, CAST ZERK, 1/4 DRIVE TYPE MOUNT, JACK RP 1 WA, SPRING LIFT RP 1 LINK, CV LIFT ARM RP 1 LINK, CV LIFT SPRING, 1.0 X LB RP 2 LINK, SPRING REF PART QTY DESCRIPTION RP 2 LINK, SPRING T RP 2 ANGLE, SPRING PIN,.50 X * 2 SCREW, HFS, 1/2 NC X 1.0 GR CLEVIS, CAT * 2 NUT, HFN 3/4 NC, DRI-LOC PATCH * 2 NUT, HFN 1/2 NC, DRI-LOC PATCH * 4 NUT, HFN 3/8 NC, DRI-LOC PATCH * 4 NUT, HFN 5/16 NC, DRI-LOC PATCH 30 W WSHR 3/4ID 2OD 3/8THICK WA, PIN 1.0 X * 2 BOLT, CARRIAGE 3/8 NC X 1 GR5 ZP * 1 BOLT, CARRIAGE 1/4 NC X 3/4 GR5 ZP RP 1 STOP LUG * 1 NUT, HFN 1/4 NC BOLT, 3/8 X 1 * Standard Hardware, Obtain Locally HHCS Hex Head Cap Screw HFS Hex Flange Screw HFN Hex Flange Nut HT Heat Treated Optional Towing Eye Kit REF PART QTY DESCRIPTION WASHER, FLAT, 1 SAE ZP WASHER, SPECIAL, 1.62 X 3 X BOLT, HEX 1 NC X 7.50 GR NUT, LOCK 1 NC BUSHING, FOR PINTLE RING 1.06X3.25X RP 1 WA, HITCH 46 W PINTLE RING, W/HARDWARE (Rev. 11/7/2017) MAN1237 (9/1/2017) Parts 43

44 SPLITTER GEARBOX ASSEMBLY REF PART PART QTY DESCRIPTION 540 RPM 1000 RPM Complete splitter gearbox Output shaft 1-3/ Seal, output double lip /8 Plug Snap ring, internal 80 mm Bearing Gear Bearing Shim set Housing Snap ring - internal 85 mm Oil seal - input Bearing Input shaft 1-3/ Snap ring - external Gear Plug - relief, 1/2-14 NPT * Lock washer, M8 split * Screw, hex M8 x 1.25P x 35 mm Cover Snap ring, external 40 mm * Standard hardware, obtain locally 44 Parts MAN1237 (9/1/2017)

45 SPLITTER GEARBOX ASSEMBLY MAN1237 (9/1/2017) Parts 45

46 WING & CENTER GEARBOX ASSEMBLY 46 Parts MAN1237 (9/1/2017)

47 WING & CENTER GEARBOX ASSEMBLY REF QTY Left Wing 540 & 1000 Right Wing 540 & 1000 Center 540 Only Center 1000 Only DESCRIPTION A Complete repair gearbox ** Gear crown 2 1 NS NS NS NS Gearbox housing Input shaft Output shaft Gear pinion Bearing cup & cone Bearing cup & cone Protective seal 9 1 * * * * Cotter pin 3/16 x Snap ring 85 UNI Snap ring 50 UNI Shim 45.3 x Shim 70.3 x Castle nut M40 x 1.5P Castle nut M30 x 2.0P Shim 50.3 x Shim 40.3 x 61.7 x Oil seal 50 x 90 x Oil seal 45 x 85 x Cap Top cover 23 6 * * * * M8 x 16 GR8.8 HHCS Dipstick, 1/2 x * * * * Cotter pin 1/4 x 2-1/ Washer, 1.22 x x Gearbox repair kit (Includes items (6, 7, 8, 10, 11, 12, 13, 18, & 19) Magnetic drain plug [NOT SHOWN] (low neck of housing) * * Crown gear placed on opposite end of input shaft for right wing * Standard hardware, obtain locally NS Not Serviced (Rev. 11/7/2017) MAN1237 (9/1/2017) Parts 47

48 540 RPM & 1000 RPM FRONT CV DRIVE REF PART QTY DESCRIPTION A Complete CV drive (540 RPM) B Complete CV drive (1000 RPM) C Complete CV drive (1000 RPM, 1-3/4") Slide lock repair kit 1C Slide lock repair kit (1000 RPM, 1-3/4") 2A Yoke QD CV (540 RPM) 2B Yoke QD CV (1000 RPM) 2C Yoke QD CV (1000 RPM, 1-3/4") CV U-Joint repair kit Cat 6 55E CV Body with fitting 5A Yoke and shaft CV splined 25.9 (540 RPM) 5B Yoke and shaft - CV splined 26.6 (1000 RPM) 5C Yoke and shaft CVSP lines 30.9 (1000 RPM) Drive shield bearing kit Decal, danger rotating driveline (see page 12) 8A CV shield outer (540 RPM) 8B CV shield outer (1000 RPM) 8C CV shield outer (1000 RPM, 1-3/4") REF PART QTY DESCRIPTION 9A CV shield inner (540 RPM) 9B CV shield inner (1000 RPM) 9C CV shield Inner (1000 RPM, 1-3/4") Decal, danger guard missing (see page 13) 11A Yoke 55R x 36.4 x (540 RPM) 11B Yoke 55R x 38.4 x (1000 RPM) 11C Yoke, tube & sleeve 55R x 39.8 x (1000 RPM, 1-3/4") U-Joint cross and bearing kit Yoke, 55R x 5.06 x SP * 1 5/8 NC Lock nut * 1 5/8 NC x 3 HHCS GR5 Not shown HHCS Hex Head Cap Screw * Standard hardware, obtain locally (Rev. 11/7/2017) 48 Parts MAN1237 (9/1/2017)

49 CENTER DECK DRIVE ASSEMBLY REF PART QTY DESCRIPTION A Complete center drive assembly Yoke, 1-3/4, 20 spline Cross & bearing kit Double yoke Grease fitting Friction clutch /4, 20 spline Flange yoke Friction disc (package of 2) REF PART QTY DESCRIPTION Hub, 1-3/4, 20 spline Thrust plate Belleville spring plate M10 x 1.5P x 55 mm HHCS M10 x 1.5P Hex lock nut M12 x 1.75P Hex lock nut M12 x 1.75P x 65 mm HHCS Clutch repair kit (includes items 7, 10, 11, 12, 13 & 14) MAN1237 (9/1/2017) Parts 49

50 WING DRIVE ASSEMBLY REF PART QTY DESCRIPTION Yoke 1 3/4"-20 SPL. I.C Cross & Bearing Kit Inboard Yoke 1B Spring pin 10 x Inner Profile 1B Profile & Sleeve WA-2AL Inboard Yoke 2A 9 2 Guard Cone 4 Rib Bearing Ring SC Guard Tube Outer 12 1 Guard Tube Inner Screw-In Item Decal Outer - In Item Decal Inner - In Item Restraint Chain Support Bearing Zerk - In Item 6 19 N/S 2 Reinforcing Collar Outer Guard Half - Incl Items 9-11, 13, 14, Inner Guard Half - Incl Items 9, 10, 12, 13, 16, 17, 19 REF PART QTY DESCRIPTION Friction Clutch 1-3/4, 20 spline Flange yoke Friction disc (package of 2) Hub, 1-3/4, 20 spline Thrust plate Belleville spring plate M10 x 1.5P x 55mm HHCS M10 x 1.5P Hex lock nut M12 x 1.75P Hex lock nut M12 x 1.75P x 65mm HHCS 8.8 N/S NOT SERVICED (Rev. 12/11/17) 50 Parts MAN1237 (9/1/2017)

51 5-BOLT WHEEL & TIRE ASSEMBLY REF PART QTY DESCRIPTION Heavy hub assembly (includes items 1 through 15) Heavy wheel hub with cups (includes items 6,7,14) Axle Seal Bearing cone Bearing cup Bearing cup Bearing cone Washer Castle nut Hub cap Stud Cotter pin Grease fitting Nut, lug 1/2 NF " Rim for pneumatic tire - 5 bolt -or x 9 Solid tire, rim & hardware - 5 bolt -or x 8-14 Severe duty ag tire, rim & hardware - 5 bolt -or- REF PART QTY DESCRIPTION F 1 25 x 8-14 Severe duty ag tire, rim & hardware, foam filled - 5 bolt x 9 x 15 Aircraft tire, rim & hardware - 5 bolt x 6.0 Rim half (for 29" aircraft wheel only) x 6.0 Rim half w/ valve hole (for 29" aircraft wheel only) * 1/2 NC x 1-1/4 HHCS GR * 1/2 NC Lock nut * 3/8 NC x 1 HHCS GR * 3/8 Standard lock washer * 3/8 NC Hex nut x 9 x 15 Inner tube (for 29" aircraft wheel only) Rim half for 6 x 9 solid tire * Standard hardware, obtain locally MAN1237 (9/1/2017) Parts 51

52 LIGHT KIT ASSEMBLY REF PART QTY DESCRIPTION A LED Light kit, complete Wire harness, 16 foot, main AG Enhancer module Wire harness, rear, 2 pieces (Includes both left & right harnesses) LED AG Combo lamp, right LED AG Combo lamp, left REF PART QTY DESCRIPTION * 2 Screw, #10 NC x 1/2 self-tapping * 8 1/4 NC x 1 HHCS, GR5 * Standard hardware, obtain locally HHCS Hex Head Cap Screw 52 Parts MAN1237 (9/1/2017)

53 CHAIN SHIELDING - CENTER & WING (REAR) (SINGLE ROW STANDARD ON BW10.50 AND BW MODELS) (DOUBLE ROW OPTIONAL ON BW10.50 AND BW15.50 MODELS) SINGLE ROW REF PART QTY DESCRIPTION /4 NC X 1.0 BUTTON HEAD SCREW RP 2 REAR CENTER RETAINER /16 CHAIN - 4 LINK /16 CHAIN - 5 LINK /16 CHAIN - 7 LINK RP 2 REAR WING CHAIN RETAINER /16 CHAIN - 6 LINK DOUBLE ROW REF PART QTY DESCRIPTION RP 2 REAR WING DOUBLE CHAIN RETAINER /16 CHAIN - 11 LINK /16 CHAIN - 13 LINK /16 CHAIN - 9 LINK RP 2 REAR CENTER DBL RETAINER (Rev. 11/7/2017) MAN1237 (9/1/2017) Parts 53

54 CHAIN SHIELDING - CENTER & WING (FRONT) (SINGLE ROW STANDARD ON BW10.50 AND MODELS) (DOUBLE ROW OPTIONAL ON BW10.50 AND BW15.50 MODELS) SINGLE ROW REF PART QTY DESCRIPTION /4 NC X 1.0 BUTTON HEAD SCREW /16 CHAIN - 4 LINK /16 CHAIN - 5 LINK /16 CHAIN - 7 LINK /16 CHAIN - 6 LINK RP 2 INNER WINGLET RETAINER RP 1 FRONT CENTER RETAINER RP 2 FRONT ENTER INNER RADUIS RETAINER RP 2 FRONT CENTER OUTER RADIUS RETAINER RP 2 STRAIGHT WINGLET RETAINER RP 2 CURVED WINGLET RETAINER RP 2 FRONT WING STRAIGHT CHAIN RETAINER RP 2 FRONT WING RADIUS CHAIN RETAINER RP 2 FRONT WING OUTER CHAIN RETAINER DOUBLE ROW REF PART QTY DESCRIPTION RP 2 STRAIGHT WINGLET DBL RETAINER RP 2 CURVED WINGLET DBL RETAINER RP 2 FRONT WING STRAIGHT DBL CHAIN RETAINER RP 2 FRONT WING RADIUS DBL CHAIN RETAINER RP 2 FRONT WING OUTER DBL CHAIN RETAINER /16 CHAIN - 11 LINK /16 CHAIN - 13 LINK /16 CHAIN - 9 LINK RP 1 FRONT CENTER DBL RETAINER RP 2 FRONT CENTER INNER RADIUS DBL RETAINER RP 2 FRONT CENTER OUTER RADIUS DBL RETAINER (Rev. 11/7/2017) 54 Parts MAN1237 (9/1/2017)

55 HYDRAULIC CYLINDERS Wing REF 3 x 10 PART OR- MAN1237 (9/1/2017) Center 3.5 x 8 PART QTY DESCRIPTION Seal repair kit (includes 2A - 2G) HD Seal repair kit w/ heavy duty piston seal (includes 2A - 2G) 2A 1 Wiper seal 2C 2 1-1/4 ID U-Cup 2D 2 Barrel O-ring 2E Rod static O-ring 2F 2 Piston back-up washer 2G 1 Pistol seal O-ring 3 NS Rod end housing 4 NS Piston Jam nut 6 NS NS 4 Cylinder tie rid /2 Pipe Plug -OR * 11893* 1 1/2 x 1/4 Pipe reducer bushing 8 NS NS 1 Cylinder butt end 9 923* 923* 4 1/4 x 1-3/4 Cotter pin x 3-5/8 Clevis pin (Rev. 11/7/2017) REF Wing 3 x 10 Center 3.5 x 8 QTY DESCRIPTION PART PART * /2 x 1/4 Pipe reducer bushing -OR /2 NPT Vent plug 12 NS NS 1 Cylinder barrel 15 * * 8 Tie rod nut Hydraulic cylinder rod clevis * 6698* 1 3/8 NC Lock nut * * 1 3/8 NC x 1-1/2 Socket head cap screw 19 NS Hydraulic cylinder rod x 10 Hydraulic cylinder - Wing /2 x 8 Hydraulic cylinder w/ breather complete * Obtain locally Not used on this cylinder Included in seal kit NS Not sold separately Parts 55

56 HYDRAULIC CYLINDERS 3.0X1.25ø ROD REF PART QTY DESCRIPTION COMPLETE CYLINDER SEAL KIT (INCLUDES ITEMS 2A-2F) 2A 2 CAP O-RING 2B 1 PISTON SEAL 2C 1 ROD O-RING 2D 1 CAP SEAL 2E 1 WIPER SEAL 2F 2 BACKUP SEAL 3 N/S 1 CYLINDER HOUSING ROD END 4 N/S 1 PISTON 5 N/S 1 JAM NUT 6 N/S 4 CYLINDER TIE ROD 7 * 3 1/2 PIPE PLUG 8 N/S 1 CYLINDER HOUSING BUTT END 9 N/S 1 CYLINDER BARREL 10 N/S 8 TIE ROD NUT 11 N/S 1 CYLINDER CLEVIS 12 N/S 1 CYLINDER ROD INCLUDED IN SEAL KIT * STANDARD HARDWARE, OBTAIN LOCALLY N/S NOT SERVICED (Rev. 11/7/2017) 56 Parts MAN1237 (9/1/2017)

57 HYDRAULIC CYLINDER STROKE CONTROL KIT REF PART QTY DESCRIPTION Stroke control set for 1-1/4" cylinder rod (contains items 2-5) /2" Segment /4" Segment 4 1 1" Segment 5 1 3/4" Segment CROSSBAR PULLER (OPTIONAL) REF PART QTY DESCRIPTION A Crossbar puller, complete Crossbar puller clevis * 4 5/8 NC x 4-1/2 HHCS GR * 4 5/8 NC Hex nut REF PART QTY DESCRIPTION Crossbar puller pad assembly Crossbar puller tube assembly Crossbar puller screw assembly Crossbar puller link * Standard hardware - obtain locally MAN1237 (9/1/2017) Parts 57

58 BW10.50 / BW10.50Q WEIGHT BOX ASSEMBLY REF PART QTY DESCRIPTION /2 FLANGE NUT LOCK /8 FLANGE NUT LOCK /8 CARRIAGE BOLT X 1-1/4 GR /2 NC X 5 GR5 HHCS RP 1 WEIGHT BOX SKID PLATE RP 1 WEIGHT BOX HINGE RP 6 WEIGHT BOX INNER PLATE RP 1 WEIGHT BOX OUTER PLATE RP 1 JACK MOUNT RP 1 WEIGHT BOX MOUNT DCL, 2 X 9 REFLECTOR /8 NC X 1.25 GR5 HHCS /8 FLANGE LOCK NUT REFLECTOR LUG HHCS HEX HEAD CAP SCREW (Rev. 11/7/2017) 58 Parts MAN1237 (9/1/2017)

59 WINCH KIT (OPTIONAL) REF PART QTY DESCRIPTION A Winch kit, complete RP 2 WINCH UPRIGHT RP 1 WINCH MOUNT CHANNEL RP 1 WINCH TIE LINK NC X 1 HEX FLANGE SCREW /8 NC FLANGE NUT X 1.25 HEX FLANGE SCREW CABLE CLAMP CABLE HOOK 9 N/S 1 1/4" X 24 FT CABLE 10 N/S 1 CLAMP KIT WINCH CLEVIS PIN 1/2 X KLIK PIN, 3/16 X CHAIN IDLER CASTING 15 N/S 4 IDLER BRACKET HFS.50NC X 1.25 GR NUT, HFN 1/2 NC, DRI-LOC PATCH N/S NOT SERVICED Winch Kit Installation 1. Locate and drill one 9/16" hole in each wing as shown. Assemble items 15, 14, 12 and 13 and use to locate and drill remaining holes. 2. Secure idler brackets (15) and rollers (14) to deck with bolts (16) and nuts (17). 3. Assemble uprights (1) to cylinder lugs using existing pins. 4. Assemble winch assembly to uprights (10) using bolts (5) and lock nuts (6). 5. Tighten all hardware. Winch Kit Operation 1. Move cutter so wing is on the up slope of a ditch to aid in wing lift with the winch. 2. Unwind cable and remove roller (14). 3. Place cable around roller (14) and reinstall using pin (12) and Klik pin (13). 4. Connect C-Hook (8) to winch mount (2). 5. Remove cylinder pin from clevis end and raise slowly with winch. 6. Install transport lock before moving unit. (Rev. 12/11/17) MAN1237 (9/1/2017) Parts 59

60 BOLT TORQUE CHART Always tighten hardware to these values unless a different torque value or tightening procedure is listed for a specific application. Fasteners must always be replaced with the same grade as specified in the manual parts list. Always use the proper tool for tightening hardware: SAE for SAE hardware and Metric for metric hardware. Make sure fastener threads are clean and you start thread engagement properly. All torque values are given to specifications used on hardware defined by SAE J1701 MAR 99 & J1701M JUL 96. A SAE SERIES TORQUE CHART SAE Grade 2 (No Dashes) SAE Bolt Head Identification SAE Grade 5 (3 Radial Dashes) SAE Grade 8 (6 Radial Dashes) A MARKING ON HEAD Diameter Wrench SAE 2 SAE 5 SAE 8 (Inches) Size lbs-ft N-m lbs-ft N-m lbs-ft N-m 1/4" 7/16" /16" 1/2" /8" 9/16" /16" 5/8" /2" 3/4" /16" 13/16" /8" 15/16" /4" 1-1/8" /8" 1-5/16" " 1-1/2" A METRIC SERIES TORQUE CHART Coarse Thread 8.8 Metric Grade 8.8 Metric Bolt Head Identification Fine Thread Metric Grade 10.9 A Marking on Head Marking on Head A Diameter & Diameter & Metric 8.8 Metric 10.9 Metric 8.8 Metric 10.9 Thread Pitch Wrench Thread Pitch (Millimeters) Size N-m lbs-ft N-m lbs-ft N-m lbs-ft N-m lbs-ft (Millimeters) 6 x mm x x mm x x mm x x mm x x mm x x mm x x mm x x mm x x mm x x mm x x mm x Typical Washer Installations :1;1 Lock Washer Flat Washer 8/9/00 Bolt Torque & Size Charts (Rev. 3/28/2007) Appendix 60

61 BOLT SIZE CHART NOTE: Chart shows bolt thread sizes and corresponding head (wrench) sizes for standard SAE and metric bolts. SAE Bolt Thread Sizes 5/16 3/8 1/2 5/8 3/4 7/8 IN MM Metric Bolt Thread Sizes 8MM 10MM 12MM 14MM 16MM 18MM AG...Agriculture ASABE... American Society of Agricultural & Biological Engineers (formerly ASAE) ASAE...American Society of Agricultural Engineers ATF...Automatic Transmission Fluid BSPP... British Standard Pipe Parallel BSPTM... British Standard Pipe Tapered Male CV...Constant Velocity CCW...Counter-Clockwise CW...Clockwise F...Female FT...Full Thread GA... Gauge GR (5, etc.)...grade (5, etc.) HHCS... Hex Head Cap Screw HT...Heat-Treated JIC... Joint Industry Council 37 Flare LH... Left Hand LT...Left m...meter mm...millimeter M... Male ABBREVIATIONS MPa...Mega Pascal N... Newton NC...National Coarse NF... National Fine NPSM... National Pipe Straight Mechanical NPT...National Pipe Tapered NPT SWF... National Pipe Tapered Swivel Female ORBM... O-Ring Boss - Male P... Pitch PBY...Power-Beyond psi...pounds per Square Inch PTO... Power Take Off QD... Quick Disconnect RH... Right Hand ROPS...Roll-Over Protective Structure RPM... Revolutions Per Minute RT... Right SAE... Society of Automotive Engineers UNC...Unified Coarse UNF... Unified Fine UNS... Unified Special 61 Appendix Bolt Torque & Size Charts (Rev. 3/28/2007)

62 ADJUSTMENTS Cutting Height 15 Slip Clutch 22 ASSEMBLY Dealer Set-Up Instructions 33 Fill Gearboxes 25 DEALER CHECK LIST Check Lists Delivery (Dealer s Responsibility) 35 Pre-Delivery (Dealer s Responsibility) 35 DEALER SERVICE Crossbar Installation 31 Removal 30 Gearbox Maintenance Seal Installation 25 Seal Replacement 25 Horizontal Shaft 26 Vertical Shaft 26 Gearbox Repair Assembly 26 Disassembly 26 Reinstallation 27 Removal 26 Splitter Gearbox Repair Assembly 28 Check Gearbox for Leaks 29 Disassembly 28 Reinstallation 29 Removal from Cutter 28 Universal Joint Assembly 32 Disassembly 31 Repair 321 GENERAL Abbreviations 61 Bolt Size Chart 61 Bolt Torque Chart 59 General Information 4 Introduction 2 Obtaining Replacement Manuals 2 Product Registration 2 Specifications 4 Table of Contents 3 Warranty Product 63 Replacement Parts 64 INDEX OPERATION Connecting Cutter to Tractor 14 Cutting Height Adjustment 15 CV Driveline Turning Limits 15 Hydraulic Connection 15 Interference Check 15 Cutter Operation 16 Mowing Tips 16 Shredding 16 Pre-Operation Check List (Owner s Responsibility) 18 Storage 18 Tractor Operation 16 Transporting 17 Lock-Up 17 Center Section 17 Wing 17 OWNER SERVICE Adjusting Slip Clutch 22 Blades Installation 21 Removal 21 Sharpening 22 Blocking Method 19 Lubrication Driveline 20 Gearbox 20 Lubrication Points 20 Seasonal 21 Shielding Repair 23 Slip Clutch Adjustment 22 PARTS Parts Index 37 SAFETY Blocking Method 19 Check Lists Delivery Check List (Dealer s Responsibility) 35 Pre-Delivery Check List (Dealer s Responsibility) 35 Pre-Operation Check List (Owner s Responsibility) 18 Free Mower Safety Video Order Form 5, 6 Safety & Instructional Decals 11, 12, 13 Safety Rules 7, 8, 9, 10 Safety Symbols Explained 2 TROUBLESHOOTING Index MAN1237 (9/1/2017)

63 WOODS shall not be liable for any incidental or consequential losses, damages or expenses, arising directly or indirectly from the product, whether such claim is based upon breach of contract, breach of warranty, negligence, strict liability in tort or any other legal theory. Without limiting the generality of the foregoing, Woods specifically disclaims any damages relating to (i) lost profits, business, revenues or goodwill; (ii) loss of crops; (iii) loss because of delay in harvesting; (iv) any expense or loss incurred for labor, supplies, substitute machinery or rental; or (v) any other type of damage to property or economic loss. This Warranty is subject to any existing conditions of supply which may directly affect WOODS ability to obtain materials or manufacture replacement parts. No agent, representative, dealer, distributor, serviceperson, salesperson, or employee of any company, including without limitation, WOODS, its authorized dealers, distributors, and service centers, is authorized to alter, modify, or WOODS A Blount International Brand 2606 South Illinois Route 2 Post Office Box 1000 Oregon, Illinois USA tel fax woodsequipment.com WARRANTY All Models Except Mow n Machine TM Zero-Turn Mowers Please Enter Information Below and Save for Future Reference. Date Purchased: _ From (Dealer): Model Number: _ Serial Number: Woods Equipment Company ( WOODS ) warrants this product to be free from defect in material and workmanship. Except as otherwise set forth below, the duration of this Warranty shall be for TWELVE (12) MONTHS COMMENCING ON THE DATE OF DELIVERY OF THE PRODUCT TO THE ORIGINAL PURCHASER. All current model backhoes, loaders and mounts (except 3-pt. SAF-T-LOK mounts) are warranted for two (2) years from the date of delivery to the original purchaser. The limited warranty covers any defects in the material and/or workmanship. Following the proper, recommended installation by an authorized Woods Dealer and normal use of a Woods mounting and backhoe or loader, if a tractor incurs damage resulting from the attachment, Woods will cover the existing tractor warranty in the event the manufacturer voids its tractor warranty because of the attachment. Warranty does not cover any misuse or abusive conditions that could cause premature wear or damage to attachment or tractor. The warranty periods for specific parts or conditions are listed below: Part or Condition Warranted Gearbox components Blade spindles Model Number All units invoiced after 4/30/2012 BB48X, BB60X, BB72X, BB84X, BB600X, BB720X, BB840X, BB6000X, BB7200X, BB8400X, DS12.50, TS14.60, DS1440, TS1680, DS8.30, DS10.40, DS8.50, DSO8.50, DS10.50, DSO10.50, DBH5.30, DBH6.30 BW12, BW15, BW126X, BW180X, BW126XHD, BW180XHD, BW1260X, BW1800X BW10.50, BW10.50Q, BW15.50, BW15.50Q, BW15.60, BW15.60Q, BW10.60, BW10.60Q BW240X, BW240XHD, BW1620X, BW2400X RD990X, PRD6000, PRD7200, PRD8400, S15CD, S20CD, S22CD, S25CD, S27CD, S30CD, TC/ R74, TC/R68, TC/R60, TBW144, TBW180, TBW204, TSG50, S12ED, S15ED, S18ED, S20ED, TPD25, TPD35, TPD65, TPD95 RDC54, RD60, RD72, TBW150C, TS/R60, TS/R52, TS/R44, RC3.5, RC4, RC5, RC6 RD990X, PRD6000, PRD7200, PRD8400, TBW144, TBW180, TBW204 Duration (from date of delivery to the original purchaser) Under no circumstances will this Warranty apply in the event that the product, in the good faith opinion of WOODS, has been subjected to improper operation, improper maintenance, misuse, or an accident. This Warranty does not apply in the event that the product has been materially modified or repaired by someone other than WOODS, a WOODS authorized dealer or distributor, and/or a WOODS authorized service center. This Warranty does not cover normal wear or tear, or normal maintenance items. This Warranty also does not cover repairs made with parts other than those obtainable through WOODS. This Warranty is extended solely to the original purchaser of the product. Should the original purchaser sell or otherwise transfer this product to a third party, this Warranty does not transfer to the third party purchaser in any way. There are no third party beneficiaries of this Warranty. WOODS makes no warranty, express or implied, with respect to engines, batteries, tires or other parts or accessories not manufactured by WOODS. Warranties for these items, if any, are provided separately by their respective manufacturers. WOODS obligation under this Warranty is limited to, at WOODS option, the repair or replacement, free of charge, of the product if WOODS, in its sole discretion, deems it to be defective or in noncompliance with this Warranty. The product must be returned to WOODS with proof of purchase within thirty (30) days after such defect or noncompliance is discovered or should have been discovered, routed through the dealer and distributor from whom the purchase was made, transportation charges prepaid. WOODS shall complete such repair or replacement within a reasonable time after WOODS receives the product. THERE ARE NO OTHER REMEDIES UNDER THIS WARRANTY. THE REMEDY OF REPAIR OR REPLACEMENT IS THE SOLE AND EXCLUSIVE REMEDY UNDER THIS WARRANTY. THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE OF THIS WARRANTY. WOODS MAKES NO OTHER WARRANTY, EXPRESS OR IMPLIED, AND WOODS SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTY OF MERCHANTABILITY AND/OR ANY IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE. 6 years 3 years (1 year if used in rental or commercial applications) 3 years F-3079 (Rev. 7/31/2017)

64 WARRANTY (Replacement Parts For All Models Except Mow n Machine TM Zero-Turn Mowers and Woods Boundary TM Utility Vehicles) Woods Equipment Company ( WOODS ) warrants this product to be free from defect in material and workmanship for a period of ninety (90) days from the date of delivery of the product to the original purchaser with the exception of V-belts, which will be free of defect in material and workmanship for a period of 12 months. Under no circumstances will this Warranty apply in the event that the product, in the good faith opinion of WOODS, has been subjected to improper operation, improper maintenance, misuse, or an accident. This Warranty does not cover normal wear or tear, or normal maintenance items. This Warranty is extended solely to the original purchaser of the product. Should the original purchaser sell or otherwise transfer this product to a third party, this Warranty does not transfer to the third party purchaser in any way. There are no third party beneficiaries of this Warranty. WOODS obligation under this Warranty is limited to, at WOODS option, the repair or replacement, free of charge, of the product if WOODS, in its sole discretion, deems it to be defective or in noncompliance with this Warranty. The product must be returned to WOODS with proof of purchase within thirty (30) days after such defect or noncompliance is discovered or should have been discovered, routed through the dealer and distributor from whom the purchase was made, transportation charges prepaid. WOODS shall complete such repair or replacement within a reasonable time after WOODS receives the product. THERE ARE NO OTHER REMEDIES UNDER THIS WARRANTY. THE REMEDY OF REPAIR OR REPLACEMENT IS THE SOLE AND EXCLUSIVE REMEDY UNDER THIS WARRANTY. THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE OF THIS WARRANTY. WOODS MAKES NO OTHER WARRANTY, EXPRESS OR IMPLIED, AND WOODS SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTY OF MERCHANTABILITY AND/OR ANY IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE. WOODS shall not be liable for any incidental or consequential losses, damages or expenses, arising directly or indirectly from the product, whether such claim is based upon breach of contract, breach of warranty, negligence, strict liability in tort or any other legal theory. Without limiting the generality of the foregoing, Woods specifically disclaims any damages relating to (i) lost profits, business, revenues or goodwill; (ii) loss of crops; (iii) loss because of delay in harvesting; (iv) any expense or loss incurred for labor, supplies, substitute machinery or rental; or (v) any other type of damage to property or economic loss. This Warranty is subject to any existing conditions of supply which may directly affect WOODS ability to obtain materials or manufacture replacement parts. No agent, representative, dealer, distributor, service person, salesperson, or employee of any company, including without limitation, WOODS, its authorized dealers, distributors, and service centers, is authorized to alter, modify, or enlarge this Warranty. Answers to any questions regarding warranty service and locations may be obtained by contacting: WOODS A Blount International Brand 2606 South Illinois Route 2 Post Office Box 1000 Oregon, Illinois USA tel fax woodsequipment.com 2017 Woods Equipment Company. All rights reserved. Woods and the Woods logo are trademarks of Woods Equipment Company. All other trademarks, trade names, or service marks not owned by Woods Equipment Company that appear in this manual are the property of their respective companies or mark holders. Specifications subject to change without notice. F-8494 (Rev. 1/3/2017)