CLUTCH SECTION CL CONTENTS
|
|
- Arleen Bell
- 6 years ago
- Views:
Transcription
1 CLUTCH SECTON CL CONTENTS HYDRAULC CLUTCH CONTROL... CL- 2 CLUTCH CONTROL. Release Bearing... CL- 6 CLUTCH UNT... CL- 7 SERVCE DATA AND SPECFCATONS (S.D.S.)... c1-10 SPECAL SERVCE TOOLS... CL-12
2 HYDRAULC CLUTCH CONTROL Push rod lock nut ( Clutch master cylinder , Operating cylinder Operating cylinder fl : Nm kg-m. ft-lbl Clutch damper securing , Precautions SCL161 0 Recommended fluid is brake fluid "DOT 3". Do not reuse drained brake fluid. 0 Be careful not to splash brake fluid on painted areas. When removing and installing clutch tube, use Tool GG To clean or wash all parts of master cylinder, operating cylinder and clutch damper, clean brake fluid mu& be used. 0 Never use mineral oils such as gasoline or kerosene. t will ruin the rubber parts of the hydraulic system. CL-2
3 8.07 Bleeding Procedure HYDRAULC CLUTCH CONTROL Adjusting Clutch Pedal Carefully monitor fluid level at master cylinder during bleeding operation. Bleed air according to the following procedure. Clutch damper + Operating cylinder 1. Top up reservoir with recommended brake fluid. 2. Connect a transparent vinyl tube to air bleeder valve. Clutch dampet or clutch switch pedal noppr ( , ).Clutch -itch Dash insulator Dash floor p anell Operating cylinder SCL204 (9) : N m im,ft-lbl SCL162 Pedal height "H" mm (7.68 ~ Pedal free play "A" 1-3 mm ( in) in) 1. Adjust pedal height with pedal stopper or clutch switch. 2. Adjust pedal free play with push rod. 3. Fully depress clutch pedal several times. 4. With clutch pedal depressed, open bleeder valve to release air. 5. Close bleeder valve. 6. Repeat steps 3 through 5 above until brake fluid comes out of air bleeder valve without air bubbles. CL-3
4 HYDRAULC CLUTCH CONTROL Adjusting Clutch Pedal (Cont'd) 3. Adjust clearance "C" between pedal stopper rubber and threaded end of clutch interlock switch while depressing clutch pedal fully. Clearance C: flacp Pedal stopper rubber! \ 1 Clutch intsrlock witch Reservoir cap Clutch Master Cylinder 7 'Piston assembly Return spring 7 Reservoir Reservoir band Winder ( Supply valve stopper ( ( Remove this stopper, when removing piston, spring seat and return spring. LMarter cylinder securing nut - ( * Always replace when dissembled (91: N.m kgm, ft-lb1 SCL163 NSPECTON Check parts for wear or damage. Replace component if any wear or damage is found. CL-4
5 Operating Cylinder HYDRAULC CLUTCH CONTROL Clutch Damper Bleeder screw p , Gasket Operating Cylinder7 Damper cover-, Piston Piston spring , cylinder '% ' \ pl Lm 8-11 ( , (018.0!L 61~., Piston cup : Nm kgm. ft-lbl m: Nm kgm,ft-lbl SCLl64 SCL205 Do not reuse piston cup and dust cover. 0 0 Do not reuse piston cup. Do not let oil touch the damper rubber as it will ruin the rubber. CL-5
6 CLUTCH CONTROL - Release Bearing Release Bearing REMOVAL AND NSTALLATON LUBRCATON Apply recommended grease to contact surface and sliding surface. Too much lubricant might cause clutch disc facing damage. CL145 Pack this recess Pres SCL167 SCL166 CL-6
7 CLUTCH UNT Clutch Unit *1: Slight burn or discoloration of contact surface with clutch disc can be corrected by polishing with emery paper. main drive shaft doer not adhere to clutch disc. \ Clutch cover sscuring bolt Clutch eaver'l SCLZOS WARNNG: Clean away clutch disc dust using a dust collector after cleaning with a cloth. Do not use compressed air. CL- 7
8 CLUTCH UNT nspecting Clutch Disc Check clutch disc for runout, etc. Runout limit of facing 1st 115 mm (4.53 in1 from the hub center1 : 1.0 mm in) nspecting Clutch Cover Check height and unevenness of diaphragm spring after setting Tool. Diaphragm spring height "A": C240S: mm ( in) C250S: mm ( in) Uneven limit: 0.5 mm (0.020 in) Maximum backlash (at outer dge of did: 1.0 mm (0.039 in) o[;/lat u or grease SCL153 T- y/a'/a- ST ST A SCL155 Check clutch disc for wear. Adjust unevenness of diaphragm spring with Tool. Measure the depth of rivet head Mora than 0.3 mm (0.012 in1 SCL207 Check thrust rings for wear or damage by shaking cover assembly up and down to listen for chattering noise, or lightly hammering on rivets for a slightly cracked noise. CL-8
9 CLUTCH UNT installing Clutch Cover nsert Tool into clutch disc hub when installing clutch cover and disc. SCL2oa CL-9
10 SERVCE DATA AND SPECFCATONS (S.D.S.) General Specifications -nspection and Adjustment CLUTCH CONTROL SYSTEM Type of clutch Control Hydraulic CLUTCH PEDAL Unit: mm (in1 Pedal height "H" CLUTCH MASTER CYLNDER nner diameter mm (in /81 CLUTCH OPERATNG CYLNDER Pedal free play "A" 1-3 ( Clearance between pedal stopper rubber and threaded end of clutch interlock witch CLUTCH DSC Unit: mm linl Model 240T8L 250T8L Ensine VG30E VG30El Facing size Outer dia. x inner dia. x thickness mm (in1 Thickness of disc assembly 70~111._., --." With load N ( ) (600 kg, 1,323 bl mm (in) Model 240TBL 25OT8L Wear limit of facing surface to rivet head Runout limit 1.0 ( Distance of runout checkpoint 115 (4.53) 120 (4.72) (from the hub center) Maximum backlash of spline la1 outer edae of d irl CLUTCH COVER Unit: mm (in) Model C240S C250S Model C240S C250S Full load 4,904 kg'bl (500. 1,1031 Diaphragm spring height Uneven limit of diaphragm spring toe height ( ( (0.020) CL-10
11 SERVCE DATA AND SPECFCATONS (S.D.S.) Tightening Torque Unit N.m kg-m ft-lb Pedal stopper lock nut Clutch switch lock nut Fulcrum pin securing nut Master cvlinder push rod lock nut Master cylinder securing nut Supply valve stopper Operating cylinder securing bolt Bleeder screw Clutch damper securing bolt Damper COYB to cylinder Clutch tube flare nut Clutch hose to operating cylinder and clutch damper securing nut Clutch mwr securing bolt VG30E VG30ET CL-11
12 SPECAL SERVCE TOOLS Tool number (Kent-Moore No.) ST (J26366) Tool name Clutch aligning bar ST ( - ) Distance piece a.:;: ,;y. ST ) Diaphragm spring adjusting wrench GGW ( - ) Flare nut torque wrench CL-12
CLUTCH SECTION CL CONTENTS C TRANSMISSION/TRANSAXLE CL-1
C TRANSMISSION/TRANSAXLE SECTION CL A B CLUTCH CL D CONTENTS E PRECAUTIONS... 2 Precautions for Supplemental Restraint System (SRS) AIR BAG and SEAT BELT PRE-TEN- SIONER... 2 Service Notice or Precautions...
More informationCLUTCH SECTION CL CONTENTS C TRANSMISSION/TRANSAXLE CL-1
C TRANSMISSION/TRANSAXLE SECTION CL A B CLUTCH CL D CONTENTS E PRECAUTIONS... 2 Precautions for Supplemental Restraint System (SRS) AIR BAG and SEAT BELT PRE-TEN- SIONER... 2 Service Notice or Precautions...
More informationCLUTCH SECTION CL CONTENTS C TRANSMISSION/TRANSAXLE CL-1
CLUTCH C TRANSMISSION/TRANSAXLE SECTION CL A B CLUTCH CL D CONTENTS E PRECAUTIONS... 2 Caution... 2 PREPARATION... 3 Special Service Tools... 3 Commercial Service Tools... 3 NOISE, VIBRATION AND HARSHNESS
More informationCLUTCH SECTION CL CONTENTS C TRANSMISSION/TRANSAXLE CL-1
CLUTCH C TRANSMISSION/TRANSAXLE SECTION CL A B CLUTCH CL D CONTENTS E PRECAUTIONS... 2 Caution... 2 PREPARATION... 3 Special Service Tools... 3 Commercial Service Tools... 3 NOISE, VIBRATION AND HARSHNESS
More informationCLUTCH SECTION CL CONTENTS TRANSMISSION & DRIVELINE CL-1 SYMPTOM DIAGNOSIS... 2 REMOVAL AND INSTALLATION...16 PRECAUTION... 4 PREPARATION...
TRANSMISSION & DRIVELINE SETION L A LUTH L ONTENTS E SYMPTOM DIAGNOSIS... 2 NOISE, VIRATION AND HARSHNESS (NVH) TROULESHOOTING... 2 NVH Troubleshooting hart...2 PREAUTION... 4 PREAUTIONS... 4 Precaution
More informationCLUTCH Nissan 240SX DESCRIPTION PEDAL HEIGHT & FREE PLAY ADJUST CLUTCH ASSEMBLY R & I Clutch. Pathfinder, Pickup, 240SX, 300ZX
CLUTCH 1990 Nissan 240SX 1990 Clutch Pathfinder, Pickup, 240SX, 300ZX DESCRIPTION Clutch is of dry, single disc type, with a diaphragm spring type pressure plate. Clutch release bearing is prelubricated.
More informationCLUTCH COMPONENT LOCATION INDEX
2005 TRANSMISSION Clutch - MX-5 Miata CLUTCH COMPONENT LOCATION INDEX Fig. 1: Identifying Clutch Components GENERAL PROCEDURES (CLUTCH) PRECAUTION Clutch pipe If any clutch pipe has been disconnected anytime
More information1. General Description
General Description 1. General Description A: SPECIFICATION Front disc brake Rear disc brake Master cylinder Brake booster Brake line Model Other models WRX MT WRX AT STi Size 15 inch type 16 inch type
More informationBRAKE SYSTEM SECTION CONTENTS F BRAKES BR-1
F BRAKES A SECTION BRAKE SYSTEM B C D CONTENTS E PRECAUTIONS... 3 Precautions for Supplemental Restraint System (SRS) AIR BAG and SEAT BELT PRE-TEN- SIONER... 3 Precautions for Brake System... 3 PREPARATION...
More informationBRAKE SYSTEM SECTION CONTENTS F BRAKES BR-1
F BRAKES A SECTION BRAKE SYSTEM B C D CONTENTS E PRECAUTIONS... 3 Precautions for Supplemental Restraint System (SRS) AIR BAG and SEAT BELT PRE-TEN- SIONER... 3 Precautions for Brake System... 3 PREPARATION...
More informationBRAKE SYSTEM Nissan 240SX DESCRIPTION BRAKE BLEEDING * PLEASE READ FIRST * BLEEDING PROCEDURES ADJUSTMENTS BRAKE PEDAL HEIGHT SPECS TABLE
BRAKE SYSTEM 1990 Nissan 240SX 1990 BRAKE SYSTEMS Nissan Disc & Drum Axxess, Maxima, Pathfinder, Pickup, Pulsar NX, Sentra, Stanza, 240SX, 300ZX DESCRIPTION All brake systems are hydraulically operated
More information1992 Clutch. Eclipse, Expo/Expo LRV, Galant, Mirage, Precis, 3000GT
Article Text ARTICLE BEGINNING 1992 Clutch Eclipse, Expo/Expo LRV, Galant, Mirage, Precis, 3000GT DESCRIPTION All clutches are single disc type. Pressure plate assembly uses a diaphragm spring to engage
More informationBRAKE SYSTEM SECTION BR CONTENTS BRAKES BR-1 PRECAUTION... 3 PREPARATION... 5 PERIODIC MAINTENANCE...14 SYMPTOM DIAGNOSIS... 6 BASIC INSPECTION...
BRAKES SECTION BR A BRAKE SYSTEM B C D CONTENTS E PRECAUTION... 3 PRECAUTIONS... 3 Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TEN- SIONER"...3 Precaution for Procedure
More information21A-1 CLUTCH CONTENTS CLUTCH... CLUTCH OVERHAUL
21A-1 CLUTCH CONTENTS CLUTCH... 21A CLUTCH OVERHAUL... 21B 21A-2 CLUTCH CONTENTS GENERAL INFORMATION... 3 SERVICE SPECIFICATIONS... 3 LUBRICANTS... 3 ON-VEHICLE SERVICE... 3 Clutch Pedal Inspection and
More informationSymptom Suspect Area See page 5. Engine mounting (Loosen) 6. Clutch disc assy (Runout is excessive) 7. Clutch disc assy (Oily)
CLUTCH CLUTCH SYSTEM (MTM) PROBLEM SYMPTOMS TABLE HINT: CLUTCH SYSTEM (MTM) Use the table below to help you find the cause of the problem. The numbers indicate the priority of the likely cause of the problem.
More informationCLUTCH SECTION CL CONTENTS TRANSMISSION & DRIVELINE CL-1 PRECAUTION... 2 PREPARATION... 4 UNIT REMOVAL AND INSTALLATION...17 SYMPTOM DIAGNOSIS...
TRSSS & DRV ST UT TTS RUT... 2 RUTS... 2 recaution for Supplemental Restraint System (SRS) "R " and "ST T R-T- SR"...2 recaution for rocedure without owl Top over...2 Service otice or recautions for lutch...2
More informationCLUTCH PREPARATION Union Nut Wrench 10 mm Clutch Guide Tool Input Shaft Front Bearing Puller
CLUTCH CL1 CL2 PREPARATION SST (SPECIAL SERVICE TOOLS) CLUTCH PREPARATION 0902300100 Union Nut Wrench 10 mm Clutch line 0930100110 Clutch Guide Tool 0930335011 Input Shaft Front Bearing Puller 0930430012
More informationBRAKE SYSTEM Return To Main Table of Contents
BRAKE SYSTEM Return To Main Table of Contents GENERAL... 2 BRAKE PEDAL... 10 MASTER CYLINDER... 13 BRAKE BOOSTER... 16 BRAKE LINE... 18 PROPORTIONING VALVE... 19 FRONT DISC BRAKE... 20 REAR DRUM BRAKE...
More informationBRAKE SYSTEM SECTION BR CONTENTS F BRAKES BR-1
BRAKE SYSTEM F BRAKES SECTION BR A BRAKE SYSTEM B C D CONTENTS E PRECAUTIONS... 3 Precautions for Supplemental Restraint System (SRS) AIR BAG and SEAT BELT PRE-TEN- SIONER... 3 Precautions for Brake System...
More informationBRAKE SYSTEM SECTION BR CONTENTS BRAKES BR-1 PRECAUTION... 3 ON-VEHICLE MAINTENANCE...12 PREPARATION... 5 FUNCTION DIAGNOSIS... 6
BRAKES SECTION BR A BRAKE SYSTEM B C D CONTENTS E PRECAUTION... 3 PRECAUTIONS... 3 Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TEN- SIONER"...3 Precautions For High-Voltage
More informationOVERHAUL. Remove the union bolt and a gasket from the disc brake cylinder, then disconnect the flexible hose from the disc brake cylinder.
OVERHAUL COMPONENTS: See page 3232 Overhaul the RH side by the same procedures with LH side. Two types of brake pad exist; one is with slit and the other without slit. 1. REMOVE REAR WHEEL 2. DRAIN FLUID
More informationBRAKE SYSTEM SECTION CONTENTS . BR- 4 BR- 6 . BR-17. BR BR- 2 BR BR-11.. BR-12. REAR DISC BRAKE (CL14H, CL14HB) - Callper
7- I BRAKE SYSTEM P BR SECTION CONTENTS BRAKE HYDRAULIC LINE.. BRAKE PEDAL..... MASTER CYLINDER. BRAKE BOOSTER FRONT DISC BRAKE (CL28VA, CL28VB) - Caliper FRONT DISC BRAKE (CL28VA, CL28VB) - Rotor REAR
More informationBRAKE SYSTEM SECTION CONTENTS F BRAKES BR-1
BRAKE SYSTEM F BRAKES A SECTION BRAKE SYSTEM B C D CONTENTS E PRECAUTIONS... 3 Precautions for Supplemental Restraint System (SRS) AIR BAG and SEAT BELT PRE-TEN- SIONER... 3 Precautions for Battery Service...
More information1994 Mazda MX-5 Miata. CLUTCH 1994 Clutch
CLUTCH 1994 Clutch DESCRIPTION Miata uses a hydraulically operated clutch. HYDRAULIC SYSTEM BLEEDING 1. Remove bleeder screw cap, located at clutch release cylinder. Install vinyl hose onto bleeder screw.
More informationBRAKE SYSTEM SECTION CONTENTS F BRAKES BR-1
F BRAKES A SECTION BRAKE SYSTEM B C D CONTENTS E PRECAUTIONS... 3 Precautions for Supplemental Restraint System (SRS) AIR BAG and SEAT BELT PRE-TEN- SIONER... 3 Precautions for Brake System... 3 PREPARATION...
More informationThis file is available for free download at
This file is available for free download at http://www.iluvmyrx7.com This file is fully text-searchable select Edit and Find and type in what you re looking for. This file is intended more for online viewing
More informationBRAKE SYSTEM SECTION BR CONTENTS F BRAKES BR-1
F BRAKES SECTION BR A BRAKE SYSTEM B C D CONTENTS E PRECAUTIONS... 3 Precautions for Supplemental Restraint System (SRS) AIR BAG and SEAT BELT PRE-TEN- SIONER... 3 Precautions for Brake System... 3 PREPARATION...
More informationCHASSIS CONTENTS EXTERIOR PARTS 6-1 FRAME COVER 6-2 REAR FRAME COVER 6-4 FRONT WHEEL 6-6 FRONT BRAKE 6-10 HANDLEBARS 6-17 FRONT FORK 6-19
CHASSIS CONTENTS EXTERIOR PARTS 6- FRAME COVER 6- REAR FRAME COVER 6-4 FRONT WHEEL 6-6 FRONT BRAKE 6-0 HANDLEBARS 6-7 FRONT FORK 6-9 STEERING 6-6 REAR WHEEL 6-3 REAR BRAKE 6-39 6 REAR SHOCK ABSORBER 6-43
More informationCHASSIS CONTENTS EXTERIOR PARTS 7-1 FRONT WHEEL 7-2 FRONT BRAKE 7-6 HANDLEBARS 7-13 FRONT FORK 7-15 STEERING 7-23 REAR WHEEL 7-26 REAR BRAKE 7-30
CHASSIS CONTENTS EXTERIOR PARTS 7- FRONT WHEEL 7-2 FRONT BRAKE 7-6 HANDLEBARS 7-3 FRONT FORK 7-5 STEERING 7-23 REAR WHEEL 7-26 REAR BRAKE 7-30 REAR SHOCK ABSORBER 7-32 SWING ARM 7-33 7 7- CHASSIS EXTERIOR
More informationREAR AXLE & REAR SUSPENSION SECTION CONTENTS
I REAR AXLE & REAR SUSPENSION RA SECTION CONTENTS REAR AXLE AND REAR SUSPENSION... RA- 2 REAR AXLE. Axle Shaft... RA- 4 DRIVE SHAFT... RA- 6 DRIVE SHAFT."Tripod-Tripod" Type... RA- 7 DRIVE SHAFT."Double
More informationOVERHAUL. Using SST, disconnect the 2 brake tubes from the master cylinder. SST
3215 320J001 OVERHAUL 1. DRAIN BRAKE FLUID Wash the brake fluid off immediately if it comes into contact with any painted surface. 2. REMOVE AIR CLEANER CAP SUBASSY 3. REMOVE (a) Disconnect the brake fluid
More informationClutch cover Type Diaphragm spring strap. Clutch pedal Type Suspended type. Maximum operating travel
000000 043 1. SPECIFICATION Operating type Description Hydraulic type Specification Clutch cover Type Diaphragm spring strap Adjusting type Clutch pedal Type Suspended type Max. operating travel Pedal
More informationA proportioning valve is used to regulate brake pressure between front and rear brakes. Rear brakes on all models are self-adjusting.
Page 1 of 21 ARTICLE BEGINNING DESCRIPTION & OPERATION WARNING: For warnings and procedures regarding vehicles equipped with Anti- Lock Brake Systems (ABS), see ANTI-LOCK BRAKE SYSTEM article in the BRAKES
More informationCHASSIS CONTENTS EXTERIOR PARTS 6-1 FRONT WHEEL 6-2 FRONT BRAKE 6-6 HANDLEBARS 6-12 REAR WHEEL 6-30 REAR BRAKE 6-34 REAR SHOCK ABSORBER 6-36
CHASSIS CONTENTS EXTERIOR PARTS 6-1 FRONT WHEEL 6-2 FRONT BRAKE 6-6 HANDLEBARS 6-12 FRONT FORK ( ) 6-14 FRONT FORK ( ) 6-20 STEERING 6-27 REAR WHEEL 6-30 REAR BRAKE 6-34 REAR SHOCK ABSORBER 6-36 6 SWING
More informationParking brake Mechanical brake acting on rear wheels
11 Brake System 11.1 General SPECIFICATIONS EJTC0010 Master cylinder Type Tandem type I.D. mm(in.) 20.64 mm (0.813 in.) Fluid level warning sensor Provided Brake booster Type Vacuum Boosting ratio 4.0
More informationBRAKE SYSTEM Article Text 1996 Toyota RAV4 For Copyright 1998 Mitchell Repair Information Company, LLC Wednesday, September 13, :30PM
Article Text ARTICLE BEGINNING 1996 BRAKES Toyota - Disc & Drum RAV4 * PLEASE READ THIS FIRST * WARNING: For warnings and procedures regarding vehicles equipped with Anti-Lock Brake Systems (ABS), see
More informationALLDATA Online Saturn L200 L4-2.2L VIN F - Base Brake Bleeding. Base Brake Bleeding
Page 1 of 9 Base Brake Bleeding BASE BRAKE BLEEDING TOOLS REQUIRED J-439l5 Brake Bleed Adapter J29532 Pressure Bleeder MANUAL BLEEDING NOTICE: Brake fluid is corrosive to painted surfaces. Take care not
More informationInstallation Instructions
Preparing your vehicle to install your brake system upgrade 1. Rack the vehicle. 2. If you don t have a rack, then you must take extra safety precautions. 3. Choose a firmly packed and level ground to
More informationSECTION 4A HYDRAULIC BRAKES
SECTION 4A HYDRAULIC BRAKES Caution: Disconnect the negative battery cable before removing or installing any electrical unit or when a tool or equipment could easily come in contact with exposed electrical
More informationON-VEHICLE SERVICE
1- CLUTCH General Information/Service Specifications/ Lubricants/On-vehicle Service GENERAL INFORMATION 110001009 The clutch is a dry single-disc, diaphragm type; hydraulic pressure is used for the clutch
More information2003 Infiniti G35. CAUTION: When brake caliper is removed, DO NOT depress brake pedal, or piston will pop out.
FRONT & REAR DISC PADS CAUTION: When brake caliper is removed, DO NOT depress brake pedal, or piston will pop out. To determine which brake system vehicle is equipped with, see MODEL IDENTIFICATION. Removal
More informationBRAKE SYSTEM SECTION BR CONTENTS F BRAKES BR-1
BRAKE SYSTEM F BRAKES SECTION BR A BRAKE SYSTEM B C D CONTENTS E PRECAUTIONS... 3 Precautions for Supplemental Restraint System (SRS) AIR BAG and SEAT BELT PRE-TEN- SIONER... 3 Precautions for Brake System...
More informationwww.clubsuprafrance.com CLUTCH 1996 Toyota Supra 1995-96 Clutch Supra DESCRIPTION The single, dry-type disc clutch uses a hydraulicallyoperated master cylinder with a clutch release cylinder mounted on
More informationDRAIN BRAKE FLUID NOTICE:
REAR DISC OVERHAUL Overhaul the RH side by the same procedure as the LH side. 1. REMOVE REAR WHEEL 2. DRAIN FLUID Wash the brake fluid off immediately if it comes into contact with any painted surface.
More informationFRONT BRAKE COMPONENTS
BR18 BRAKE SYSTEM FRONT BRAKE COMPONENTS REPLACEMENT OF BRAKE PADS HINT: If a squealing noise occurs from the front brakes while driving, check the pad wear indicator. If there are traces of the indicator
More informationCLUTCH Toyota Celica DESCRIPTION ADJUSTMENTS CLUTCH PEDAL HEIGHT Clutch. Celica
CLUTCH 1993 Toyota Celica 1993 Clutch Celica DESCRIPTION The single, dry disc type clutch uses a hydraulically operated master cylinder and a release cylinder mounted on clutch housing. Clutch release
More informationThis file is available for free download at
This file is available for free download at http://www.iluvmyrx7.com This file is fully text-searchable select Edit and Find and type in what you re looking for. This file is intended more for online viewing
More informationDISC BRAKE/DUAL MASTER CYLINDER CONVERSION. Tools, Equipment and Supplies Needed:
Please take the time to read the enclosed instructions carefully. If you have any questions, call our Product Assistance personnel for clarification. It is important to note that these instructions contain
More informationBRAKE SYSTEM SECTION CONTENTS F BRAKES BR-1
F BRAKES A SECTION BRAKE SYSTEM B C D CONTENTS E PRECAUTIONS... 3 Precautions for Supplemental Restraint System (SRS) AIR BAG and SEAT BELT PRE-TEN- SIONER... 3 Precautions for Brake System... 3 Wiring
More informationILLUSTRATION ILLUSTRATION
ILLUSTRATION ILLUSTRATION REMOVAL 1. DISABLE BRAKE CONTROL (a) Wait at least 2 minutes after the power switch off. When the brake pedal is depressed or the door courtesy switch is turned on even if the
More informationANTI-LOCK BRAKE SYSTEM
ANTI-LOCK BRAKE SYSTEM 1992 Infiniti G20 1990-92 BRAKES Infiniti Anti-Lock Brake System Infiniti; G20, M30, Q45 DESCRIPTION & OPERATION The Anti-Lock Brake System (ABS) prevents wheel lock-up during abrupt
More informationBRAKE SYSTEM TROUBLESHOOTING CHECKS AND ADJUSTMENTS MASTER CYLINDER BRAKE BOOSTER REAR BRAKE
BR-1 BRAKE SYSTEM PRECAUTIONS TROUBLESHOOTING CHECKS AND ADJUSTMENTS MASTER CYLINDER BRAKE BOOSTER VACUUM PUMP FRONT BRAKE REAR BRAKE Drum Brake Disc Brake Parking Brake LOAD SENSING PROPORTIONING AND
More informationTools, Equipment and Supplies Needed:
153-162 DISC BRAKE/DUAL MASTER CYLINDER CONVERSION Please take the time to read the enclosed instructions carefully. If you have any questions, call our Product Assistance personnel for clarifi cation.
More informationBRAKE SYSTEM SECTION BR CONTENTS F BRAKES BR-1
BRAKE SYSTEM F BRAKES SECTION BR A BRAKE SYSTEM B C CONTENTS E PRECAUTIONS... 3 Precautions for Supplemental Restraint System (SRS) AIR BAG and SEAT BELT PRE-TEN- SIONER... 3 Precautions for Brake System...
More informationGENERAL PROCEDURES. Component Bleeding. Master Cylinder Priming In-Vehicle or Bench
206-00-1 Brake System General Information 206-00-1 GENERAL PROCEDURES Component Bleeding Special Tool(s) Worldwide Diagnostic System (WDS) 418-F224, New Generation STAR (NGS) Tester 418-F052, or equivalent
More information2010 Toyota Prius Repair Manual
REMOVAL 1. DISABLE BRAKE CONTROL (a) Wait at least 2 minutes after the power switch off. NOTICE: When the brake pedal is depressed or the door courtesy switch is turned on even if the power switch is off,
More information1999 Toyota RAV BRAKES Disc & Drum - Trucks & Vans
DESCRIPTION & OPERATION 1999-2000 BRAKES Disc & Drum - Trucks & Vans WARNING: For warnings and procedures regarding vehicles equipped with Anti-Lock Brake Systems (ABS), see appropriate ANTI-LOCK article.
More informationFRONT & REAR SUSPENSION SECTIONSU CONTENTS IDX. FRONT SUSPENSION...2 Precautions...2
FRONT & REAR SUSPENSION SECTIONSU GI MA EM LC CONTENTS EC FE FRONT SUSPENSION...2 Precautions...2 PRECAUTIONS...2 Preparation...2 SPECIAL SERVICE TOOLS...2 COMMERCIAL SERVICE TOOLS...2 Noise, Vibration
More information12. FRONT WHEEL/FRONT BRAKE/
12 4.5kgm 0.9kg-m 4.5kg-m 12-0 SERVICE INFORMATION... 12-1 HYDRAULIC BRAKE... 12-10 TROUBLESHOOTING... 12-2 FRONT SHOCK ABSORBER... 12-16 FRONT WHEEL... 12-3 STEERING HANDLEBAR... 12-19 FRONT BRAKE...
More informationBRAKE SYSTEM SECTION CONTENTS F BRAKES BR-1
F BRKES SECTION BRKE SYSTEM B C D CONTENTS E PRECUTIONS... 3 Precautions for Supplemental Restraint System (SRS) IR BG and SET BELT PRE-TEN- SIONER... 3 Precautions for Brake System... 3 Wiring Diagrams
More informationBRAKE SYSTEM SECTIONBR CONTENTS
BRAKE SYSTEM SECTIONBR CONTENTS PRECAUTIONS...3 Supplemental Restraint System (SRS) AIR BAG and SEAT BELT PRE-TENSIONER...3 Precautions for Brake System...3 Wiring Diagrams and Trouble Diagnosis...4 PREPARATION...5
More informationA 1 SERVICE SPECIFICATIONS
A1 A2 Clutch CLUTCH Specifications Pedal height (from asphalt sheet) Release point (from pedal stroke end position) Push rod play at pedal top Pedal freeplay Disc rivet head depth Disc runout Diaphragm
More information12. FRONT WHEEL/FRONT BRAKE/
12 12 12-0 SERVICE INFORMATION... 12-1 FRONT BRAKE... 12-7 TROUBLESHOOTING... 12-2 FRONT SHOCK ABSORBER... 12-18 STEERING HANDLEBAR... 12-3 FRONT FORK... 12-21 FRONT WHEEL... 12-4 SERVICE INFORMATION GENERAL
More informationCLUTCH GROUP 21A 21A-1 CONTENTS CLUTCH PEDAL AND MASTER CYLINDER... 21A-4 GENERAL INFORMATION... 21A-2 SERVICE SPECIFICATIONS...
21A-1 GROUP 21A CONTENTS GENERAL INFORMATION 21A-2 SERVICE SPECIFICATIONS 21A-2 LUBRICANTS 21A-2 ON-VEHICLE SERVICE 21A-2 PEDAL CHECK 21A-2 BLEEDING 21A-3 PEDAL AND MASTER CYLINDER 21A-4 REMOVAL AND INSTALLATION
More informationSECTION 4A BRAKE SYSTEM TABLE OF CONTENTS
SECTION 4A BRAKE SYSTEM TABLE OF CONTENTS Description and Operation... 4A-2 Braking System Testing... 4A-2 Hydraulic Brake System... 4A-2 Brake Pedal... 4A-2 Master Cylinder... 4A-2 Brake Booster... 4A-3
More informationCHASSIS CONTENTS FRONT WHEEL 6-1 FRONT BRAKE 6-7 FRONT FORK 6-14 STEERING 6-18 REAR WHEEL AND REAR BRAKE 6-22
CHASSIS CONTENTS FRONT WHEEL 6- FRONT BRAKE 6-7 FRONT FORK 6-4 STEERING 6-8 REAR WHEEL AND REAR BRAKE 6-6 6- CHASSIS FRONT WHEEL REMOVAL AND DISASSEMBLY Remove the front brake caliper by removing the mounting
More information16. BRAKE SYSTEM 16-0 BRAKE SYSTEM UXV 500
16 BRAKE SYSTEM 16 SERVICE INFORMATION------------------------------------------------ 16-1 TROUBLESHOOTING----------------------------------------------------- 16-2 BRAKE PADS REPLACEMENT-----------------------------------------
More informationBRAKE SYSTEM SECTIONBR CONTENTS IDX
BRAKE SYSTEM SECTIONBR GI MA EM LC EC CONTENTS FE PRECAUTIONS...4 Supplemental Restraint System (SRS) AIR BAG and SEAT BELT PRE-TENSIONER...4 Precautions for Brake System...4 Wiring Diagrams and Trouble
More informationDRAIN BRAKE FLUID NOTICE:
OVERHAUL Overhaul procedure of the RH side is the same as that of with LH side. 1. REMOVE REAR WHEEL 2. DRAIN BRAKE FLUID Wash off the brake fluid immediately if it comes into contact with a painted surface.
More informationFRONT BRAKE COMPONENTS
BR18 COMPONENTS BRAKE PADS REPLACEMENT HINT: If a squealing noise occurs from the brakes while driving, check the pad wear indicator plate. If the pad wear indicator plate contacts the disc, the brake
More informationSECTION BR CONTENTS BRAKE SYSTEM IDX
BRAKE SYSTEM SECTION BR GI MA EM PRECAUTIONS AND PREPARATION... 3 Supplemental Restraint System (SRS) AIR BAG and SEAT BELT PRE-TENSIONER... 3 Precautions for Brake System... 3 Commercial Service Tools...
More informationThis chapter covers the location and servicing of the front brake components for the KYMCO MXU 700i and MXU 500i models.
KYMCO MXU 500i/700i Repair Manual Brake System 9.Brake System This chapter covers the location and servicing of the front brake components for the KYMCO MXU 700i and MXU 500i models. 1.Brake Discs... 9-3
More informationSERVICE PROCEDURES FOR CLUTCH HYDRAULIC UNITS
SERVICE PROCEDURES FOR CLUTCH HYDRAULIC UNITS SAFETY PROCEDURES Always follow the vehicle manufacturer's recommended safety procedures in your Shop and Owners Manual. REQUIRED TOOLS Flat blade screwdriver,
More informationMASTER CYLINDER INSPECTION
7-16 CHASSIS A-PDF Split DEMO : Purchase from www.a-pdf.com to remove the watermark Remove the piston assembly. MASTER CYLINDER INSPECTION MASTER CYLINDER Inspect the master cylinder bore for any scratches
More informationBRAKE SYSTEM SECTION BR CONTENTS F BRAKES BR-1
BRAKE SYSTEM F BRAKES SECTION BR A BRAKE SYSTEM B C CONTENTS E PRECAUTIONS... 3 Precautions for Supplemental Restraint System (SRS) AIR BAG and SEAT BELT PRE-TEN- SIONER... 3 Precautions for Brake System...
More informationClutch System Troubleshooting Guide-Service Tips
DESCRIPTION AND OPERATION Clutch System The purpose of the clutch is to connect and disconnect a manually operated transmission and the remainder of the powertrain system from the engine. This permits
More informationSERVICE BRAKES GROUP 35A 35A-1 CONTENTS GENERAL DESCRIPTION... 35A-2 BRAKE PEDAL... 35A-22 BASIC BRAKE SYSTEM DIAGNOSIS 35A-3
35A-1 GROUP 35A CONTENTS GENERAL DESCRIPTION 35A-2 BASIC BRAKE SYSTEM DIAGNOSIS 35A-3 INTRODUCTION TO BASIC BRAKE SYSTEM DIAGNOSIS 35A-3 BASIC BRAKE SYSTEM DIAGNOSTIC TROUBLESHOOTING STRATEGY 35A-3 SYMPTOM
More informationFRONT AXLE SECTION CONTENTS D DRIVELINE/AXLE FAX-1 FAX
FRONT AXLE D DRIVELINE/AXLE A SECTION FRONT AXLE B C FAX CONTENTS E PRECAUTIONS... 2 Caution... 2 PREPARATION... 3 Special Service Tools (SST)... 3 Commercial Service Tools... 3 NOISE, VIBRATION AND HARSHNESS
More informationREAR AXLE SECTION CONTENTS D DRIVELINE/AXLE RAX-1 RAX
REAR AXLE D DRIVELINE/AXLE A SECTION REAR AXLE B C RAX CONTENTS E PRECAUTIONS... 2 Caution... 2 PREPARATION... 3 Special Service Tools... 3 Commercial Service Tools... 4 NOISE, VIBRATION AND HARSHNESS
More informationCL - Clutch Replacement
2003 3.2CL - Clutch Replacement Special Tools Required Pressure plate compressor 07AAE-P8EA000 Clutch alignment shaft 07AAF-P8EA000 Pressure plate compressor adapter 07AAK-P8EA000 Ring gear holder 07LAB-PV00100
More informationFRONT AXLE SECTION FAX CONTENTS TRANSMISSION & DRIVELINE FAX-1 PRECAUTION... 2 REMOVAL AND INSTALLATION... 6 PREPARATION... 3
TRANSMISSION & DRIVELINE SECTION FAX A FRONT AXLE B C FAX CONTENTS E PRECAUTION... 2 PRECAUTIONS... 2 Precaution...2 PREPARATION... 3 PREPARATION... 3 Special Service Tool...3 Commercial Service Tool...3
More informationBRAKE SYSTEM Toyota Celica DESCRIPTION DRUM BRAKES ADJUSTMENTS BRAKE PEDAL HEIGHT ADJUSTMENTS BRAKE PEDAL FREE PLAY ADJUSTMENTS
BRAKE SYSTEM 1988 Toyota Celica 1988-89 BRAKES Toyota Celica, Corolla, MR2, Tercel DESCRIPTION The hydraulic brake system uses a tandem master cylinder with a vacuum power assist servo. MR2 and some Celica
More informationDF 78. HINT: Face the rough side of the thrust washer marked by # to the differential case. INSPECTION
78 DIFFERENTIAL REAR DIFFERENTIAL CARRIER ASSEMBLY (w/ Differential Lock) Face the rough side of the thrust washer marked by # to the differential case. INSPECTION 1. DIFFERENTIAL SIDE GEAR (w/ LSD Differential)
More informationServicing front brakes
46-1 Servicing front brakes C54 brake caliper, servicing Special tools and workshop equipment required VAG 1331 Torque wrench (or equivalent) VAG 1410 Torque wrench (or equivalent) VAG 1869/2 Brake pedal
More informationSECTION 3A FRONT DRIVE AXLE TABLE OF CONTENTS SPECIFICATIONS GENERAL SPECIFICATIONS. Description Drive Shaft Type. CV Joint Axle Housing Type
SECTION 3A FRONT DRIVE AXLE TABLE OF CONTENTS Specifications........................ 3A-1 General Specifications.................. 3A-1 Fastener Tightening Specifications......... 3A-2 Component Locator...................
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS PERFORMANCE AT THE WHEELS KIT W120-22, W120-23 1964 1/2-69 MUSTANG Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs. Pleases take the time to read
More informationFRONT & REAR AXLE SECTIONAX CONTENTS. FRONT AXLE...2 Precautions...2
FRONT & REAR AXLE SECTIONAX CONTENTS FRONT AXLE...2 Precautions...2 PRECAUTIONS...2 Preparation...2 SPECIAL SERVICE TOOLS...2 COMMERCIAL SERVICE TOOLS...2 Noise, Vibration and Harshness (NVH) Troubleshooting...3
More informationMANUAL TRANSMISSION SECTION MT CONTENTS TRANSMISSION/TRANSAXLE MT-1 SERVICE INFORMATION POSITION SWITCH...13 Checking...13
TRANSMISSION/TRANSAXLE SECTION MT A B MANUAL TRANSMISSION MT D CONTENTS E SERVICE INFORMATION... 2 PRECAUTIONS... 2 Service Notice or Precaution...2 PREPARATION... 3 Special Service Tool...3 Commercial
More informationFRONT AXLE SECTION CONTENTS D DRIVELINE/AXLE FAX-1 FAX
D DRIVELINE/AXLE A SECTION FRONT AXLE B C FAX CONTENTS E PRECAUTIONS... 2 Precautions... 2 PREPARATION... 3 Special Service Tools... 3 Commercial Service Tools... 3 NOISE, VIBRATION, AND HARSHNESS (NVH)
More information19. HYDRAULIC BRAKE 19-1 SYSTEM COMPONENTS FRONT MASTER CYLINDER SERVICE INFORMATION 19-3 FRONT BRAKE CALIPER 19-15
19. HYDRAULIC BRAKE SYSTEM COMPONENTS- 19-2 FRONT MASTER CYLINDER 19-10 SERVICE INFORMATION 19-3 FRONT BRAKE CALIPER 19-15 TROUBLESHOOTING 19-4 REAR MASTER CYLINDER 19-18 BRAKE FLUID REPLACEMENT/ REAR
More informationCLUTCH 6-1 CLUTCH CONTENTS
TJ CLUTCH 6-1 CLUTCH CONTENTS page GENERAL INFORMATION CLUTCH COMPONENTS... 1 INSTALLATION METHODS AND PARTS USAGE... 1 DESCRIPTION AND OPERATION CLUTCH OPERATION... 1 DIAGNOSIS AND TESTING DIAGNOSTIC
More informationRelease the electrical wire from the bracket -2- toward the left -A- and remove.
Page 1 of 8 Front Brake Pads, FBC-60, Removing and Installing Always replace on both axles. Special tools and workshop equipment required t Torque Wrench 5 50 Nm -V.A.G 1331- t Reversible Ratchet -V.A.G.
More informationFRONT AXLE SECTION FAX CONTENTS DRIVELINE/AXLE FAX-1 SERVICE INFORMATION... 2
DRIVELINE/AXLE SECTION FAX A FRONT AXLE B C FAX CONTENTS E SERVICE INFORMATION... 2 PRECAUTIONS... 2 Caution...2 PREPARATION... 3 Special Service Tool...3 Commercial Service Tool...3 NOISE, VIBRATION AND
More informationin the 1970 Ford Car Shop Manual, Volume One, Chassis. It is strongly recommended that a Shop Manual be obtained and followed.
1970 Trans Am Mustang Front Disk brake instructions 1. The installation of this kit follows the standard procedures described in the 1970 Ford Car Shop Manual, Volume One, Chassis. It is strongly recommended
More informationM-2300-M Mustang GT Rear Disc Brake Bracket Kit INSTALLATION INSTRUCTIONS
Please contact the Tech Line for the most current instruction information (800) 367-3788!!! PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION!!! INTRODUCTION: This kit allows for the
More informationCHASSIS CONTENTS FRONT WHEEL 6-1 FRONT BRAKE 6-6 FRONT FORK 6-14 STEERING STEM 6-20 REAR WHEEL AND REAR BRAKE 6-25 SUSPENSION 6-31 REAR SWING ARM 6-36
CHASSIS CONTENTS FRONT WHEEL 6-1 FRONT BRAKE 6-6 FRONT FORK 6-14 STEERING STEM 6-20 REAR WHEEL AND REAR BRAKE 6-25 SUSPENSION 6-31 REAR SWING ARM 6-36 6 6-1 CHASSIS FRONT WHEEL REMOVAL Support the machine
More informationfor filling and bleeding hydraulic disk brake systems Instruction
Seite 1 von 6 Instruction All processes described in this instruction are applicable for brake fluid DOT4 and hydraulic fluid based on mineral oil. Never the less the fluids must never be mixed up, otherwise
More informationFRONT AXLE AND SUSPENSION FA 1
FRONT AXLE AND SUSPENSION FA1 FRONT AXLE AND SUSPENSION FA2 FRONT AXLE AND SUSPENSION Troubleshooting TROUBLESHOOTING Problem Possible cause Remedy Page Wanders/pulls Tires worn or improperly inflated
More informationBRAKE SYSTEM SECTION CONTENTS F BRAKES BR-1
BRAKE SYSTEM F BRAKES A SETION BRAKE SYSTEM B D ONTENTS E PREAUTIONS... 3 Precautions for Supplemental Restraint System (SRS) AIR BAG and SEAT BELT PRE-TEN- SIONER... 3 Precautions for Procedures without
More informationFRONT WHEEL AND BRAKE DISCS. Order Job/Part Q ty Remarks Removing the front wheel and brake discs NOTE:
FRONT WHEEL AND BRAKE DISCS EAS00514 SIS FRONT WHEEL AND BRAKE DISCS 1 2 3 4 Order Job/Part Q ty Remarks Removing the front wheel and brake discs Remove the parts in the order listed. Place the motorcycle
More information