Automation Swing Gate Opener

Size: px

Start display at page:

Download "Automation Swing Gate Opener"

Sara Megan Reeves
6 years ago
Views:

1 Automation Swing Gate Opener Operating and installation instructions Elegant 3

3 CONTENTS ) DESCRIPTION ) TECHNICAL SPECIFICATIONS 3) THE INSTALLATION TOOLS 4) THE PACKING LIST 5) THE INSTALLATION

4 .DESCRIPTION The ELEGANT 3 automated system for swing gates comprises an electromechanical operator which drives the gate leaves by means of a worm screw. The ELEGANT 3 operator is irreversible and locks mechanically when the motor is not in use, there for a lock does not need to be fitted. ATTENTION: The ELEGANT 3 automated system was designed and manufactured to control access of vehicles. Avoid any other use whatever. The control systems must be installed at a minimum height of.5m from the ground surface and not interfere with the mobile parts. Command pulses must be given from sites where you can see the gate. Use transmitters only if you can see the gate.. Features of this product: This product is configured with an advanced automation control system, allowing many years of fault-free, easy and safe operation. This product adopts advanced driving mode and most suitable driving system, eliminating safety hazards. This uses a DC motor with low noise. This product features fully automated soft start and shutdown, and stable and quiet operation. This system is provided with obstacle detection, stopping and backing functions to protect nearby personnel and property. This product is configured with internal interfaces of complete functions and plug-and-play operation. This product has most prevailing outline structural design. External parts of this product are elaborately treated to prevent accidental injury due to touching. This product has elaborately designed installation structure to facilitate installation. This product has elaborately designed internal structure to facilitate maintenance.. Structure of this product:.. The dimension of the shape:.. The internal structure: (fig.0) fig.0 fig.0.rear bracket.external arm 3.Motor 4.Pin 5.Spring 6.Arm 7.Dish 8.Dish 9. Bearing 0. Wormscrew. Bearing. Downboard 3. Longscrew 4. Lockcover 5. Screw 6. Screw 7. Lockboard 8. Lock 9. Upboard 0. Screw. Bearing. Front fitting

5 . TECHNICAL SPECIFICATIONS. Technical specifications TECHNICAL SPECIFICATIONS Power supply (V) Power (W) Thrust (dan) Current (A) Speed (m/sec) Travel (mm) Max Leaf weight (Kg) Protectionc l a s s Working temperature ELEGANT 3 DC4V 4W 400N A 0.8m/s 400mm 00Kg IP54 >-0ºC, <50ºC 3. THE INSTALLATION TOOLS There are some operating tools before installation as follow: (fig.03) fig THE PACKING LIST You must check the operator packing before the installation of the automated system. (fig.04) fig.04 NO NAME AMOUNT NO NAME AMOUNT Gearmotor 8 Screw 3 Control Box Door Bracket 9 0 Pin Bracket Wall Bracket Rear Bracket Remote Control Key 3 4 Exp a n d e d s c r e w Exp a n d e d s c r e w Lock screw (M6) Lock screw (M8)

6 5. THE INSTALLATION 5. Pre-installation checks ATTENTION: To ensure a correct operation of the automated system, make sure the following requirements are observed as for the gate structure (existing or to be realised) The leaf must be fixed firmly on the hinges to the pillars and must not be flexible during the movement Rotating gate shall be solid wood gate, metal gate or glass aluminum gate; Before the installation of ELEGANT 3, verify all dimension, etc. The mechanical parts must conform to the provision of standards EN604 and EN605. Leaf length in compliance with the operator specification. Sturdy and stiff structure of the leaves, suitable for automation Regular and uniform movement of the leaves, without any friction and dragging during the en t i r e o p e n i n g. Presence of an efficient earthing for electrical connection of the operator Rotating gate shall be two-leaf, and the stops must be added in the path. 5. Installation layout fig.05 fig.06. Operators. Photocells 3. Con t r o l b o a r d 4. Ke y - o p e r a t e d p u s h - b u t t o n 5. Receiver 6. Fl a s h i n g l a m p NOTE. Use suitable tubes and/or hoses to lay electric cables. To avoid any kind of interference always separate low-voltage accessories and control cables from 30V power supply cable using separate sheaths. If not standard layout, all equipment must be carefully selected. 5.3 Door opening angle and depth parameters Max. 0 for this product; if this shall be 90, a stop must be added in the path. angle depth m a x 70mm 40mm 40mm 0mm fig.07 Adjust opening to your preference. This left figure shows an example of such case (maximum opening angle is 90 ). (fig.08) fig.08

7 5.4 Minimum installation gate opening clearance Rotating gate must not be in contact with wall (to avoid potential hazard); minimum clearance between gate and wall shall be 00mm to avoid injury; Gate opening is adjusted by stopper; stopper can be used to adjust distance between gate and wall, while adjusting opening angle. To allow max. angle of opening, make sure to treat walls. Installation for inward opening of gate. 5.5 Minimum installation height fig.09 This system is fully electrically driven; output is at bottom where there is potential hazard; do not get near. Output device of this system is at bottom and certain installation requirements apply. Bottom of compound box shall be at least 50mm to ground. Installation for outward opening fig Minimum side clearance System fully electrically driven. Driving arm has certain rotation radius (with potential hazard). Don t stay near. Driving arm has large rotation radius and certain installation requirements apply. Driving arm shall be at least 500mm to walls. fig. fig. Inward opening installation side clearance fig.3 Outward opening installation side clearance 5.7 Gate opening angle commissioning parameters 5.7. Installation depth D 5.7. Installation translation distance B fig.4 fig.5 fig.6

8 (EN) B Support (EN) A Support stroke engine ELEGANT 3 W X Y Z 95º º After fixing machine slide rod on fixing plate, use marker pen to mark on the gate. Drill holes at markings on the gate and use spare screws to lock the fixing plate. fig.7 fig.8 ATTENTION: At lower part of the gate opening machine, pointed part is system clutch. In case of fault or loss of power, use key to open the clutch. Key Lockbox c o v e r fig.9 fig.30

9 Before installing fixing support, drill mounting holes on wall with electric drill and embed expansion tube in wall. Then put fixing support horizontal and use screws to lock mounting plate. During locking of mounting plate, fixing support must be adjusted horizontal. fig Prepare gate opening machine and use a spare V power supply or battery to push slide rod to its position. Me t h o d o f connection Directionof d o o r o p e n i n g b y t h e m a c h i n e fig.36 fig According to commissioning parameters, installed fixing support on main unit of gate opening machine. fig After fixing machine slide rod on fixing plate, use marker pen to mark on the gate and drill holes on markings on door and use spare screws to lock fixing plate. fig.40 fig.4

Automation Swing Gate Opener

Automation Swing Gate Opener Operating and installation instructions SP EIFFEL 400 V1.0 Rev 08/01 CONTENTS 0) GENERAL SAFETY REGULATIONS...Page 0 1) DESCRIPTION...Page 03 ) TECHNICAL SPECIFICATIONS 3)