Installation and Operation Manual for E4OD and 4R100 Transmissions

Transcription

1 Installation and Operation Manual for E4OD and 4R100 Transmissions

2 US Shift Transmission Control System instruction and operation manual. Baumann Electronic Controls, LLC. Phone: (864) Address: 207 Mistr Lane, Pickens, SC This work and the ideas and processes contained herein are the exclusive property of Baumann Electronic Controls, LLC and may not be copied, reproduced, or distributed in any form without the express written consent of Baumann Electronic Controls, LLC or Karl Baumann. The technology and processes contained in this product are proprietary and may be used only on a single unit basis or as defined by the written permission of Baumann Electronic Controls, LLC. vf4.0.1 Copyright by Baumann Electronic Controls, LLC. All rights reserved. WARRANTY Baumann Electronic Controls, LLC. is dedicated to producing the highest quality products available in the industry and is committed to customer satisfaction. Because we have no control over the circumstances under which our products are used, we can assume no more responsibility for damages (consequential or otherwise) or defects in materials and workmanship than the original purchase price of our product. Baumann Electronic Controls, LLC. will repair or replace all defective components unconditionally for a period of five years from the date of sale. This warranty does not cover damages due to abuse, improper application, or connection of the device. After the warranty period, Baumann Electronic Controls, LLC. will service this device for a nominal fee. APPLICATION COVERAGE This system works with all E4OD and 4R100 automatic transmissions. It is recommended that you use the US Shift wiring harness with this system. 2

3 CONTENTS Preparation Page 4 Connecting the Essentials Page 5 Setting up the Quick 4 Page 9 Notes on Installation Page 11 Transmission Diagrams Page 13 Optional Features Page 18 Manual Shift Connections Page 23 Shiftware Page 29 Important Information Page 32 Troubleshooting Error Codes Page 33 Contact Page 35 READ BEFORE PROCEEDING Before installing the Quick 4 unit, we recommend you read the manual from beginning to end. Some of the information in this manual is very important and, if the unit is improperly installed or an error code misunderstood, could result in serious damage to your vehicle and transmission. 3

4 PREPARATION Pre-1995 Transmissions The Quick 4 does not support the early ATR (MLPS or Range Sensor) connector used from 1989 to It was found to not be adequately waterproof. Ford services the old sensor by providing the new one with the updated connector shell and instructions for replacing it. If you don t already have the 1995 and up range senor, you will need to purchase it. US Shift sells the updated range sensor as well as Ford. 4

5 Step 1: Ground Splice the ground wires (Pins 15 & 16 Black) from the Quick 4 into the main ECU (Engine Control Unit) ground wire. Do NOT connect the ground wires to sheet metal or other ground sources. The Quick 4 MUST be connected to the Main ECU ground, as close to the ECU as possible. CONNECTING THE ESSENTIALS (ELECTRONIC FUEL INJECTION) Step 2: Power Splice the power wire (Pin 9 Red with 7.5 Amp fuse) from the Quick 4 into the main ECU (Engine Control Unit) ignition-switched power wire. Step 3: Throttle Position Sensor or Accelerator Pedal Position Sensor Splice the Throttle Position Sensor signal wire (Pin 3 Green) from the Quick 4 into the Throttle Position Sensor (TPS) signal input of the ECU (Engine Control Unit). If the vehicle has Electronic Throttle Control, use the Accelerator Pedal Position (APP) Sensor instead of the TPS. 5

6 CONNECTING THE ESSENTIALS (CARBURETED AND MECHANICALLY-INJECTED DIESEL) Step 1: Ground Connect the ground wire (Pin 15 Black) from the Quick 4 directly to the battery ground post or negative battery cable. Do NOT connect the ground wire to sheet metal or other ground sources. The Quick 4 MUST be connected directly to the battery ground post or negative battery cable. Step 2: Power Connect the power wire (Pin 9 Red with 7.5 Amp fuse) from the Quick 4 to ignitionswitched power wire. Do NOT use accessoryswitched power. Step 3: Throttle Position Sensor Attach the 3 Throttle Position wires from the Quick 4 to the Throttle Position Sensor. Pin 16 Black is dedicated ground. Pin 11 Orange is +5v reference feed. Pin 3 Dark Green is the position sensor signal. See the "Throttle Position Sensor" section for details. 6

7 7

8 Step 4: Transmission Connectors Connect the Solenoid, PRNDL, and TSS cables to the transmission. Additionally, connect the Neutral Safety Switch and the Backup Lamp Switch (See page 16). An output shaft speed sensor, a VSS, or an electronic speedo can be used for speed input. Step 5: Optional Features Connect any extra features you wish to use. See the "Optional Features" section for details. 8

9 SETTING UP THE QUICK 4 Step 6: Calibration For a detailed video walkthrough of the setup process, scan the QR code to the right using your smart phone. You can also find the video on USshift.com. Verify that the correct calibration is loaded on the Quick 4. A standard calibration specific to your order is loaded before shipment. However, if the transmission configuration has changed since the order was placed, you'll need to connect the Quick 4 to a Windows PC and install the Shiftware Tuning Software. (See the Shiftware section for installation instructions.) Using the software, load the calibration that matches your transmission's configuration. 9

10 Step 7: Throttle Position Sensor Calibration Set the Closed Throttle and Full Throttle Positions. This step should be done with the ignition turned to ON, but the engine off. The engine should also be warm. Turn the knob to Tune (tne) and click once. Closed Throttle Position (CtP) should be displayed. Leave the accelerator untouched. Click the knob once, then double-click to set the current Closed Throttle Position. Click again to exit. Turn the knob to Full Throttle Position (FtP). Hold the accelerator all the way down. Click the knob once, then double-click to set the current Full Throttle Position. Click again to exit. Turn the knob to Save and Exit (SAE). Click once to save and exit. 10

11 NOTES ON INSTALLATION If any error codes or unexpected characters are displayed, refer to the troubleshooting section at the end of this manual for detailed explanations. General Installation The Quick 4 unit should be mounted within the passenger compartment of the vehicle in a protected location. Good mounting areas include under the dash, behind a kick panel, or under the seat, as long as the unit and wiring are not subject to damage. Under-hood mounting is NOT possible with the Quick 4 unit. It is not waterproof or rated for under-hood temperatures. Passenger compartment mounting is also necessary to provide easy access to the USB port, which is used to interface with a PC for programming and diagnostics, as well as the display and function control knob. For this reason, be sure to mount the unit in a way that gives easy access to the USB port, knob, and display. If you will be using a desktop PC for programming, install the unit so that it can be unplugged and moved easily. All electrical connections should be made using 60/40 rosin core solder. Cover the connection with heat-shrinkable tubing for improved insulation and mechanical strength. Individual connector terminals can be connected using a piggy-back method, where the terminal is removed from the plastic connector housing to allow the new wire to be soldered on to the terminal atop the original wire. Two wires may be connected together by twisting them together longitudinally, soldering, then covering with the appropriate size heat-shrink tubing. Before Driving the Vehicle Start the engine and move the shifter through all positions, ensuring that the gear position and all sensor readings shown on the controller are correct. Most importantly, make sure that no error codes are shown on the Quick 4 display. It is a good idea to periodically check the Quick 4 display for errors as you drive, so it is wise to consider an accessible mounting location. If possible, perform a line pressure check to ensure that line pressure is correct at idle (typically 60-80PSI), and that it smoothly increases toward maximum (typically PSI) as the throttle position increases. If you have any questions about the installation or line pressure readings, please contact our technical support department. 11

12 Adaptation for Factory-Equipped Transmissions It is possible to use the Quick 4 controller in a vehicle which was originally equipped with one of the intended transmissions. This could be done in conjunction with an engine management system upgrade that no longer supports the transmission. Use of the controller for this purpose allows flexibility in choosing the engine management system, in addition to the increased control, performance, and transmission durability afforded by Quick 4. If you retain the stock PCM/VCM, it can probably be modified or re-flashed to disable the transmission functionality. Identifying the Terminals of an Unknown Throttle Position Sensor This is a procedure for identifying the correct terminal connections of any potentiometer-style throttle position sensor (almost all three-terminal TP sensors). A DVOM or analog Ohmmeter is required. 1. Set the meter to resistance mode and set it to a scale that can read up to 10K or 20K Ohms (if it is not auto-ranging). Please keep in mind when setting up and reading the meter that "K" means thousands of Ohms. In other words, 15K Ohms is the same as 15,000 Ohms. 2. Connect the meter to two pins at a time while operating the lever or cam of the TPS. Watch the meter while rotating the sensor. Check all three pairs of pins until you find a pair that does not change resistance when you rotate the sensor. The two pins that do not change resistance are the fixed ends of the resistance element (+5V and ground). The remaining pin that did change is known as the "wiper". It is the moving contact that slides along the resistance element to give the varying voltage. This is the output terminal of the sensor and should be connected to our green wire (Vehicle pin 3). 3. Next, with the sensor at the idle or closed throttle position, measure the resistance between the wiper (output) and each of the end terminals (the two whose resistance did not change in step 2) of the sensor. The end terminal with the lowest resistance to the wiper (at idle) is the ground terminal, and should connect to the black main ground wire of the controller (Vehicle pin 16). The terminal with the higher resistance to the wiper is the 5 volt reference input to the sensor and should connect to the orange wire (Vehicle pin 11) in our harness. General Guidelines for setting up Throttle Position Sensors The linkage to a throttle position sensor should use most of the rotating range of the throttle position sensor. This can be adjusted by changing the ratio of the linkage. Also, please make sure that a small amount of the sensor's travel is being used at idle. You will want a TPS voltage at idle of at least 0.35 volts. This is done to allow the controller to detect problems with the TP sensor. For instance, if the sensor becomes disconnected or the linkage falls off, the TPS voltage will fall below the set idle threshold. If the TPS voltage goes below the idle threshold, the controller assumes that the TPS is bad and will switch to failsafe line pressure and default shift points. This is done to prevent damage to the transmission from low line pressure and will provide a safe "limp home" mode. 12

13 TRANSMISSION DIAGRAMS 13

14 14

15 15

16 16

17 17

18 OPTIONAL FEATURES MULTI-TUNE This feature allows completely different calibrations to be used for the transmission at any time. The table selection switch can be a latching type switch (maintained toggle switch, latching push-button, etc.) or a momentary type switch (spring-loaded push-button switch, spring-loaded toggle switch, etc.) which applies ground to the table select input at Vehicle connector pin 5 when turned on. When a latching switch is used, it can only be used to switch between two tables. When the latching switch is activated, the controller will use the secondary calibration table (normally table 2), and it will run off of the primary table (normally table 1) when the switch is off. A momentary switch will cycle through all of the tables in use ( ). The Table Selection input may also be connected to a nitrous oxide system to provide an alternate calibration for use when the nitrous system is engaged. Other uses for this input include a Sport/Economy switch or a Normal/Aggressive switch. Whenever the table state is changed, it will be scrolled on the controller s display (tb1, tb2, tb3, tb4). There are alternative table select input methods that can be used. You can hold the O/D button for 2 seconds, single-click the controller knob while at the status screen, or attach a latching or momentary switch to the brown wire (pin 4). This would free up the purple wire (pin 5) to be a low-range selection switch. Different modes can be selected in the tuning software which will select different tables for different situations. For example, Select Tables Using Only 4WD Mode will use table 1 in 2WD and 4WD high range, with table 2 for 4WD low range (Tables 3-4 will be used for the second and third low ranges, if equipped) If a switch is connected to the table select wire, Select Tables Using Switch and 4WD Mode chooses tables 1 or 2 in 2WD mode and table 3 or 4 in 4WD (depending on switch position). Select Tables Using O/D On-Off Mode will choose the table according to the Overdrive switch. O/D On will use table 1, O/D Off will use table 2, and Manual mode will use table 3 (if enabled). 18

19 4x4 Low Range Detection Low range detection can be enabled if you want the controller to switch to an alternate calibration table when 4x4 low range is engaged. Configure the options in Shiftware under the 2WD/4WD Options and Table Select tabs in the settings window. For example, 4x4 low range detection can be enabled so that when ground is applied to pin 5 (purple) of the vehicle harness, the controller will switch to table 2. Other options include holding the O/D switch for 2 seconds or single-clicking the controller knob to enable 4x4 low range calibration. Up to 3 low range ratios can be used. Whenever 4x4 low-range state is changed, it will be scrolled on the controller s display (4HI, 4Lo, 4L2, 4L3). Speedometer Output We have provided an adjustable speed signal output on the tan wire on pin 12 of the vehicle connector that can be used to drive an electronic speedometer, if desired. Use of this output signal is not necessary, but it can be helpful if your speedometer can not be driven correctly from another source. This signal can also be corrected for different gear ratios and tire heights, so it can be very useful in some applications. The speedometer output signal is normally provided as a 5 Volt square wave, but it can also be configured to provide a 12 Volt square wave when required (please refer to the "jumper settings" document for more information). There are two speedometer output modes that can be selected via the tuning software or the built-in tuning interface. It can also be disabled if not used. In the replicated speed sensor output mode, the speedometer output provides an amplified and squared version of the original speed sensor signal. Replicated mode is useful for applications that require a signal with the exact pulse rate of the speed sensor being used. There is also an adjustable corrected mode, which is very useful for correcting speedometer errors or providing unusual speedometer output signal frequencies. Adjustable mode is essentially the electronic equivalent of a ratio corrector gear box for a mechanical speedometer. In adjustable mode, the correction factor is entered as a decimal number. The correction factor is the frequency ratio of the speedometer output frequency to the speed sensor frequency. This number can be easily adjusted to synchronize the vehicle speedometer to a GPS or other instrument. 19

20 In some cases, such as driving the input of an engine control ECU, the 0-5 Volt (or 0-12 Volt) square wave signal will not be able to properly drive the device that it is connected to. This is because some devices are only designed to accept an input signal from a variable reluctance (magnetic coil) sensor. Because of this, they may expect the input signal to swing below ground (0 Volts). To drive this type of input, use the included capacitor to "offset" the DC value of the speedometer signal to 0 Volts. As a result, the driven device will see a -2.5V to +2.5V signal instead of 0V to 5V. To make this signal work, install the provided 10µF, 25v, non-polar, electrolytic capacitor inline between the speedometer output of the Quick 4 and the device that it is driving. To install the capacitor, cut the speedometer output wire and solder a capacitor lead to each of the two cut wires. Tachometer Signal Input The tachometer input can be connected to a digital tachometer output from an engine computer or the tachometer output from an MSD ignition or similar CDI (Capacitive Discharge Ignition) system, but NEVER to the coil outputs of a CDI system like MSD. For breaker points (or conventional electronic ignition systems such as GM HEI, Ford Duraspark or TFI), it can be connected to the coil negative terminal. For COP (Coil on Plug) ignition systems that do not have a conventional tachometer output (such as later Mustang engines), one of the coil trigger wires can be used, but the update rate will be slow. A better approach for such applications would be to use a tachometer adapter such as the AutoMeter Overdrive On-Off Switch The Overdrive switch can be used to turn overdrive on or off. The switch can be a latching switch (toggle switch, latching push-button, etc.) or a momentary type switch (spring-loaded push-button switch, spring-loaded toggle switch, etc.) connected to +12v ignition-switched power and pin 4 (brown) of the vehicle harness. (The tan wire on pin 12 is for VSS output and shouldn t be confused with the brown wire on pin 4 for the O/D switch.) A momentary switch is needed to use more than 2 states. Optionally, you can add an O/D indicator lamp between +12v ignition-switched power and pin 2 (white) of the vehicle harness. This lamp will normally light up when overdrive is off. Also, without adding a switch, a single-click of the controller s knob can turn overdrive on and off. This setting can be configured under the Flex-Shift tab of the tuning software. Whenever the O/D or manual state is changed, it will be scrolled on the controller s display (O-d On, O-d Off). 20

21 The FLEX-SHIFT Settings window. O/D settings are at the bottom. To use an LED bulb for the O/D light (without built-in resistors for 12v), connect the cathode (-) lead to the white wire on pin 2 of the vehicle harness and the anode (+) lead to +12v ignition-switched power. Put a resistor in series on either side. We recommend using a 1.2k Ohm resistor, but you can use one with a lower resistance to make the LED brighter or one with a higher resistance to make it dimmer. It s best to stay above 1k Ohm to protect the LED. A 1/4w resistor or higher is recommended. 21

22 22

23 MANUAL SHIFT CONNECTION Manutronic Overview If connected and enabled in the software, the ManuTronic feature will allow manual selection of all forward gears using paddles, buttons, or another type of switch. With ManuTronic engaged, a brief press of the UPSHIFT button will change to the next higher gear, while DOWNSHIFT will change to the next lower gear. ManuTronic also has a safety feature which inhibits downshifting if the engine RPM is too high, which prevents over-revving of the engine due to a driver's error. Manutronic Reference Supply (JW2-5) There are several different ways to configure the Manutronic to meet your specific needs. Depending on your Manutronic configuration, you may need to install or uninstall the Manutronic jumper (JW2-5). You can find the jumper settings manual on the Quick 4 software disc in PDF format. This jumper supplies 5V to the Manutronic 1 input and should be installed for all Manutronic configurations (except for a Ford cruise control system). See the sections below for further explanation. 23

24 Ford Cruise Buttons For this configuration, you will need to solder the Dark Blue wire (Pin 14 on the Vehicle Connector) to the Blue / Black striped wire that connects the steering wheel buttons to the cruise module. (Follow the guidelines for soldering found in the General Installation section.) The Light Blue wire is not needed for this configuration. The Manutronic jumper should not be installed in the Quick 4 controller. Be sure to use the correct settings in the Shiftware setup. To enable the Manutronic, double-click the CRUISE OFF button. Press ON or OFF once to disable it. 24

25 Ford Cruise Buttons without Cruise Module For this configuration, you will need to connect the Dark Blue wire (Pin 14 on the Vehicle Connector) to the steering wheel buttons. (Follow the guidelines for soldering found in the General Installation section.) The Light Blue wire is not needed for this configuration. Remember that the Manutronic jumper must be installed in the Quick 4 controller and the correct settings used in the Shiftware setup. To enable the Manutronic, double-click the CRUISE OFF button. Press ON or OFF once to disable it. 25

26 Momentary Shift Buttons with Latching On / Off Switch For this configuration, you will need to connect the Dark Blue wire (Pin 14 on the Vehicle Connector) to your down-shift button (momentary) and connect the Light Blue wire (Pin 6 on the Vehicle Connector) to your up-shift button (momentary). To connect the on / off switch (latching), solder the switch's wire onto the Dark Blue down-shift wire with a 680 Ohm resistor between them. (Follow the guidelines for soldering found in the General Installation section.) Remember that the Manutronic jumper must be installed in the Quick 4 controller and the correct settings used in the Shiftware setup. Manutronic will be enabled when the toggle switch is turned on and disabled when it is turned off. 26

27 Momentary Shift Buttons with Momentary On / Off Switch For this configuration, you will need to connect the Dark Blue wire (Pin 14 on the Vehicle Connector) to your down-shift button (momentary) and connect the Light Blue wire (Pin 6 on the Vehicle Connector) to your up-shift button (momentary). To connect the on / off switch (momentary), solder one side of the switch onto the Dark Blue down-shift wire and the other side to the Light Blue up-shift wire. (Follow the guidelines for soldering found in the General Installation section.) Remember that the Manutronic jumper must be installed in the Quick 4 controller and the correct settings used in the Shiftware setup. To enable the Manutronic, press the On/Off button once and do the same to disable it. 27

28 Twist Machine Shrifter TM For this configuration, you will need to connect the Dark Blue wire (Pin 14 on the Vehicle Connector) to COM2 of the receiver and connect the Light Blue wire (Pin 6 on the Vehicle Connector) to COM1 of the receiver. You can use either a momentary push-button on / off switch or a latching toggle on / off switch. (Refer to the previous two sections on how to install and use the on / off switch.) Remember that the Manutronic jumper must be installed in the Quick 4 controller and the correct settings used in the Shiftware setup. 28

29 SHIFTWARE Introduction Using the Shiftware software allows you to modify the way your Quick 4 Transmission Control System behaves. You can customize shift-points as well as monitor and diagnose the Quick 4 unit in real-time. Setup To create a calibration for the Quick 4, it is best to start with one of the standard calibrations which are included with the software. To load a standard configuration for your transmission, click the Open button on the toolbar, then browse to the folder where the transmission calibration files are located. (Default location is C:\Shiftware\) The files are named according to the transmission and RPM range and have the.btc file extension. Choose the calibration file and click Open. Once the calibration file is loaded, click the System Settings button on the toolbar to check the settings and make sure that they are correct for your transmission. The System Settings window has several tabs within it. Click each one to see each section of settings specific for your transmission. The System Settings Window 29

30 Customize The main window is where all of the shift points and line pressure editing is done. The graph displays the up-shift and down-shift speeds in relation to throttle position for each shift. It also displays the line pressure & firmness curve in relation to throttle position. The line pressure curve is displayed in PSI, so the higher the curve, the more firm shifts will be. You can use the checkboxes on the right to turn on the curves for individual shift firmness and adjust them independently. The Main Window You can get help on anything by clicking the Question button (or the F1 key) and then clicking on an item. This can be used in any area of the software. The help messages in the settings pages are transmission-specific and are more like getting professional advice than normal help tips. The graph has ten points from left to right, 0 being idle and 9 being Wide-Open- Throttle (WOT). On the left side of the graph is the shift speed. When you hover over a graph point, you can also see the corresponding shift speed in RPM or the applicable unit values for items other than shift points. Click on a point in the graph to select it. 30

31 If Select Pairs Together is enabled, then the corresponding down-shift point will be automatically selected along with the up-shift point. This can be turned off by clicking the Select Pairs Together checkbox on the right. You can select multiple points by holding CTRL while clicking the points or a range of points by holding SHIFT and clicking the two points on each end. You can move between adjacent points using the LEFT and RIGHT arrow keys. Once a point (or points) is selected, you can drag it with the mouse to raise and lower its value. A yellow box will appear in the graph telling you what the value of the point is. Adaptive Learning By default, the Quick 4 will learn the shift and TCC timing characteristics of your transmission. It will complete a learning cycle over the first few hard-throttle passes and will use the learned data to optimize shifts. For learning to occur, the tachometer input signal must be connected and functioning properly. During the learning cycle, you may notice unusual TCC operation. This is normal and will end once learning is complete. Once learned, the data will not change unless it is erased using the clear (CLr) command on the controller s display. Clearing the data will cause another learning cycle to begin. For optimum accuracy, learning should be done at the same transmission fluid temperature that it will be run at during normal operation. Once learned, shift point accuracy will only be limited by the consistency of your transmission s valve body. If you wish to disable learning, enter Settings in the tuning software and switch to the Miscellaneous tab. Uncheck Enable Learned Shift Timing. This will stop the controller from using learned data, but will not erase the learned data. This would be useful if you plan to make changes to the transmission or are unable to complete a proper learning cycle. Save & Load Once you have created your calibration, you can save the file to your hard drive or an external storage device. To save, click the Save button on the toolbar. Then, browse to the location where you want it saved and click Save. Use Save As under the FILE menu to leave the original file unchanged and create a new version. Type the desired filename and click Save. Files are saved with a.btc extension. To load a calibration file, click the Open button on the toolbar. Then, browse to the file and click Open. 31

32 Writing a Calibration to the Quick 4 For the changes you've made to take effect on the Quick 4 controller, you first must write the calibration to the unit. Connect the Quick 4 to your computer using a standard USB cord (Type A to Type B). Click the Write Calibration button on the toolbar and a menu will appear. If you aren t using multiple calibrations, click the All Tables button to save the calibration to the controller. The Quick 4 can now be disconnected from the computer and installed in the vehicle. (To use multiple tables, you can create a new calibration and choose one of the other table buttons when writing to the controller.) When the Quick 4 unit is disconnected from the computer, the Write Calibration button will be grayed out. IMPORTANT INFORMATION How to Avoid Errors The Shiftware software gives you complete freedom and flexibility to customize your shifting calibration however you want. This freedom requires diligence to avoid errors. It is very important that the up-shift and down-shift curves for a given gear do not cross. The up-shift point at any throttle position should usually be at least 15% greater than the down-shift point. For instance, if the 2-3 up-shift point at ½-throttle is 45MPH, then the 3-2 down-shift point should usually be less than 40MPH. The On-Off differential between up-shift and down-shift points is called Deadband (also known as Hysteresis). The more deadband you use for your shift points, the more stable the system will be. Not using enough deadband can result in erratic shift behavior. Too much deadband will result in sluggish behavior due to a reluctance to down-shift. Pay close attention to the interaction between different shifts. Overlapping the 1-2 and 2-3 shifts can cause skipped gears and other drivability problems. Also note that torque converter slip at low speeds renders engine RPM values meaningless. It is usually desirable to have light-throttle shift points within a low RPM range. In this case, it is best to base light-throttle shift points on vehicle speed rather than engine RPM (as most auto manufacturers do). 32

33 TROUBLESHOOTING ERROR CODES WARNING! If the transmission does not begin to operate correctly within the first few feet of the road test, STOP immediately, check the troubleshooting guide, and call Baumann Electronic Controls if you need assistance. In some cases, just a few blocks of operation with low fluid pressure can destroy a transmission. Error Codes: The following error codes will be shown on the controller's display when faults are detected. For more detailed error messages, you can also view the Controller Fault Display in the tuning software. The software is not limited to currently set faults, but can show fault history as well. History is cleared when the controller powers down completely (ignition turned off and USB cable removed from computer.) Scan the QR Code to be directed to the corresponding troubleshooting guide webpage or visit t1x.us. F:bL Battery voltage is too low (Less than 8 volts) t1x.us/211 F:bH Battery voltage is too high (More than 17.2 volts) t1x.us/212 OCP Pressure control solenoid overcurrent error (Pressure control disabled, max line pressure) t1x.us/213 OC1 Overcurrent error in solenoid bank 1 (Outputs disabled) t1x.us/214 OC2 Overcurrent error in solenoid bank 2 (Outputs disabled) t1x.us/215 OC3 Overcurrent error in solenoid bank 3 (Outputs disabled) t1x.us/216 F:tP Throttle position sensor value has dropped below the minimum (idle) voltage setting t1x.us/210 F:tL Transmission fluid temperature sensor voltage is too low (Possible short to ground) t1x.us/218 F:tH Transmission fluid temperature sensor voltage is too high (Possible open circuit in sensor or wiring harness) t1x.us/219 Hot Transmission is overheating (Fluid temperature is above warning temperature setting) t1x.us/220 33

34 F:OS Output Shaft Speed Sensor Missing or Open t1x.us/221 F:IS The Input Shaft (Turbine) Speed Sensor (if equipped) is open or missing t1x.us/222 F:C1 Checksum error in table 1 (Use tuning software to reload table 1 tune) t1x.us/2a F:C2 Checksum error in table 2 (Use tuning software to reload table 2 tune) t1x.us/2b F:C3 Checksum error in table 3 (Use tuning software to reload table 3 tune) t1x.us/2c F:C4 Checksum error in table 4 (Use tuning software to reload table 4 tune) t1x.us/2d CSL Torque converter clutch slip detected when fully engaged t1x.us/224 F:SL Transmission appears to be slipping in at least one gear t1x.us/208 FSS Transmission continued to slip after maximum line pressure was commanded t1x.us/208 rsl Transmission slip was detected more than twice in this drive cycle (max. line pressure latched) t1x.us/208 F:rE Transmission gear ratio appears to be too high in at least one gear t1x.us/225 F:rS There are several errors which can cause this code to appear. The Controller Fault Display in the tuning software will differentiate between all of the errors listed which show the F:rS error code on the controller. Analog range sensor voltage or PWM duty cycle is out of tolerance, but is within approximate range for a given position. Controller is configured for a PWM range sensor, but no PWM signal was detected. Digital range sensor signal combination is not valid. Analog range sensor voltage or PWM duty cycle below low limit (Possible short to ground). Analog range sensor voltage or PWM duty cycle above high limit (Possible open sensor). Ford digital range sensor analog window voltage is too low (Possible short on TR3A pin). Ford digital range sensor analog window voltage is too high (270 Ohm resistor on TR3A pin not detected) t1x.us/203 34

35 CONTACT If you have any questions, problems, or product orders, don t hesitate to call our customer service line. (864) (Monday-Friday 10AM-6PM EST). If no one is available, please leave a detailed message and we will reply promptly. Whenever possible, we will try to return urgent technical support calls left after hours or over the weekend. You can also customer service at support@usshift.com Scan this code to copy the customer service phone number and address to your phone. 35