Datasheet. DIN Rail Mount

Transcription

1 DRH Series Ratings up to 18 & 20 Amps at 600VAC Fits standard 35mm DIN Rail Integrated over-temperature protection Alarm output in case of over-temperature Multicolor LED with input status and alarm indicator AC or DC control Zero Voltage (resistive loads) or instantaneous (inductive loads) turn-on output C-UL-US Listed, IEC Rated, CE & RoHS Compliant, Horsepower Rated Built-in Overvoltage Protection Fan controlled through thermistor and microprocessor to optimize fan operation PRODUCT SELECTION Control Voltage 18A VAC/VDC DRH3P60A VDC DRH3P60D18 20A DRH3P60A20 DRH3P60D20 AVAILABLE OPTIONS Series Required for valid part number For options only and not required for valid part number OUTPUT SPECIFICATIONS (1) Operating Voltage (47-63Hz) [VRMS] Transient Overvoltage [Vpk] (2) Maximum Off-State Leakage Rated Voltage [marms] Minimum Off-State Maximum Rated Voltage [V/μsec] Load Current, General Use 40 C [ARMS] (3) Function 3P: Contactor DRH 3P 60 A 18 U R Operating Voltage 60: VAC Control Voltage A: VAC/VDC D: 4-32 VDC Switching Type Blank: Zero Voltage Turn-On R: Instantaneous Turn-On Rated Load Current 18: 18 Amps (3 Controlled legs) 20: 20 Amps (2 Controlled legs) 18A 20A Load Current, Motor Starting UL C [ARMS] (3) Minimum Load Current [ARMS] Maximum Surge Current [Apk] 1Cycle 60Hz Maximum Surge Current [Apk] 1Cycle 50Hz Maximum I²t for Fusing (8.33 msec) [A²sec] Maximum I²t for Fusing (10 msec) [A²sec] Maximum On-State Voltage Rated Current [Vpk] 1.35 per channel 1.35 per channel Minimum Power Factor (with Maximum Load) Motor Rating UL 508/ IEC [HP/kW] :240 VAC 2/1.5 2/1.5 Motor Rating UL 508/ IEC [HP/kW] :380 VAC 3/2.2 3/2.2 Motor Rating UL 508/ IEC [HP/kW] :480 VAC 5/3.7 5/3.7 INPUT SPECIFICATIONS (1) DRH3P60Dx DRH3P60Ax Control Voltage Range 4-32 VDC VAC/VDC Minimum Turn-On Voltage 4 VDC 90 VAC/VDC Must Turn-Off Voltage 1 VDC 10 VAC Minimum Input Current (for on-state) 2 ma 1 ma Maximum Input Current 17 ma 3 ma Nominal Input Impedance [Ohms] 2k 100k Maximum Turn-On Time [msec] 1 Cycle (4) 30 Maximum Turn-Off Time [msec] 1 Cycle 40

2 POWER SUPPLY SPECIFICATIONS (1) DRH3P60Dx Voltage Range 8-32 VDC Minimum Turn-On Voltage 8 VDC Must Turn-Off Voltage 3 VDC Maximum Source Current [ma] 125 Maximun Start Up Time [msec] 20 Maximun Shut Off Time [msec] 40 DRH3P60Ax VAC/VDC 90 VAC/VDC 5 VAC/VDC ALARM OUTPUT (1) Maximum Contact Switching Voltage [Volts] Contact Rated Current [A] Minimum Recommended Contact Load [ma] Static Contact Resistance (max. init.)[ohms] Turn-On / Off Condition DRH3P60xxx 200 VDC, 120 VAC See Status Chart GENERAL SPECIFICATIONS (1) Parameters Dielectric Strength, Input/Output/Base (50/60Hz) (5) 3750 Vrms Minimum Insulation Resistance (@ 500 VDC) 10 9 Ohm Maximum Capacitance, Input/Output 20 pf Ambient Operating Temperature Range (6) -10 to 70 C Ambient Storage Temperature Range -40 to 70 C Weight (typical) 2 Controlled Legs (7.4 oz [210 g]) / 3 Controlled Legs (8.5 oz [242 g]) Housing Material UL94 V-0 Housing Color Black and Light Gray LED Status Indicator (color) See Status Chart Short Circuit Current Rating (7) 100kA Pollution Degree 2 Protection Degree (8) IP20 Humidity 85% non-condensing Control and Auxiliary Contact Terminal Screw Torque Range (in-lb/nm) 12 / 1.36 Load Terminal Screw Torque Range (in-lb/nm) 15 / 1.7 Input Terminal Wire Capacity AWG (IEC 1-4 mm 2 ) (stranded /solid) Output Terminal Wire Capacity AWG (IEC 1-6 mm 2 ) (stranded /solid) THERMAL DERATE INFORMATION Single unit (9) DRH3P60x18 Multiple units Single unit (9) DRH3P60x20 Multiple units Load Current (Amps) Ambient Temperature (ºC) Load Current (Amps) Ambient Temperature (ºC)

3 WIRING AND BLOCK DIAGRAM L1 L2 L VAC, 50-60Hz L1 L2 L3 / > / > / > Power Supply VAC/VDC (for A Control Voltage) 8-32 VDC (for D Control Voltage) Alarm Output (0.5 A/200 VDC, 120 VAC) Normally Open L1 L2 L3 XXXX +A3 13 +A1 DRH3P60xxx IND. CONT. EQ. INPUT STATUS -A4 14 -A2 T1 T2 T3 CONTROL INPUT Motor Controller / AC-53a Application T1 T2 T3 General Use / AC-51 Application T1 T2 T3 T1 T2 T3 M 3 DRHP60x18 (3 controlled legs model) Main Circuit Alarm Output (DRHP60x18 & DRHP60x20) +A3 L1 L2 L3 +A1 13 -A4 T1 T2 T3 -A2 14 DRHP60x20 (2 controlled legs model) Main Circuit +A3 L1 L2 L3 +A1 -A4 T1 T2 T3 -A2

4 SHORT CIRCUIT AND OVERLOAD PROTECTION FOR ALL DEVICES IEC standard make a distinction between two different types of protection, (called coordination ), which are designated types 1 and "2". Any short-circuit that occurs is cleared safely by either type of coordination. The only difference between the 2 categories concerns the extent of the SSR damage caused by the short-circuit. Type "1" coordination requires that in the event of a short-circuit, the does not endanger personnel or installations, but permanent damage to the SSC is permissible. In this case the SSC may need to be replaced. For this type of co-ordination, the use of fusing or circuit breakers adequate to protect the system and wiring from short circuits, (but not specifically considering SSC protection), can be used. Type "2" coordination requires that under a short-circuit condition, the circuit is interrupted, the SSC does not endanger persons or installations, and in addition the SSR will be able to operate after the fault condition is repaired. Type of coordination 1 For resistive loads: Nominal Current Protection by Thermal Magnetic Circuit Breaker or by Fuse Class gg fuses (example from Littlefuse) 2 controlled legs 3 controlled legs A CY14X51G25 DRH3P60x20 DRH3P60x18 (up to 18A) (10) For motor loads: Protection by Thermal Magnetic Circuit Breaker or by Fuse Nominal Motor Current Thermal Magnetic Circuit Breaker (Schneider Electric) Class gg fuses (example from Littlefuse) 2 controlled legs 3 controlled legs A GV2ME04 / GV2P04 CY14X51G16 DRH3P60x20 DRH3P60x A GV2ME05 / GV2P05 CY14X51G16 DRH3P60x20 DRH3P60x A GV2ME06 / GV2P06 CY14X51G25 DRH3P60x20 DRH3P60x A GV2ME07 / GV2P07 CY14X51G25 DRH3P60x20 DRH3P60x A GV2ME08 / GV2P08 CY14X51G25 DRH3P60x20 DRH3P60x A GV2ME10 / GV2P10 CY14X51G40 DRH3P60x20 DRH3P60x A GV2ME14 / GV2P14 CY14X51G40 DRH3P60x20 (up to 7.6A) DRH3P60x18 (up to 7.6A) (10) Type of coordination 2 For resistive loads: Nominal Current Protection by Fuse Semiconductor fuses with less than 2330 A 2 s Littlefuse SIBA1 (Cylindric) Ferraz (Cylindric) 2 controlled legs 3 controlled legs A LA50QS Z DRH3P60x20 DRH3P60x18 (up to 18A) (10) For motor loads: Nominal Motor Current Protection by Fuse Semiconductor fuses with less than 2330 A 2 s Littlefuse SIBA1 (Cylindric) Ferraz (Cylindric) 2 controlled legs 3 controlled legs A LA50QS A DRH3P60x20 DRH3P60x18 (10)

5 STATUS CHART Control Input A Power Supply A3 Output Over Temperature Alarm Pre-alarm Alarm Output LED Color 2s 3s 0% 50% 75% 100% 100% 75% 50% 3s 3s Fan Speed Step LED Color 1, 15 2, , 12 5, 11 6, Initial Condition Stand by condition. LED is blinking Blue. Fan is activated at full speed for 2 seconds after power is applied to A3 A1 is On, Output is activated, temperature rises. LED is Green Fan is activated at 50% speed. If A1 is disabled, LED changes to blinking Blue Fan is at 75% speed LED changes to blinking Red, fan is at full speed Output is Off, Alarm Output is On, LED changes to solid Red If A1 is disabled while alarm output is active, LED alternates between Blue and Red LED is solid Red, temperature starts to fall Fan is activated at 50% speed, temperature is steady Blue Green Red MECHANICAL SPECIFICATIONS 0.23 [5.8] 2.91 [73.9] 3.51 [89] Tolerances: ±0.02 in / 0.5 mm All dimensions are in: inches [millimeters] +A3 13 +A [86.7] 1.23 [31.3] 2.29 [58.3] 2.58 [65.5] DRH3 IND. CONT. EQ [42.7] XXXX INPUT STATUS -A4 14 -A [95.6] 1.78 [45.3] TERMINAL SCREW TYPE Top/Bottom view (Fig. 1) Fig. 1

6 ACCESSORIES ID Marker ID Marker CNLB CNLN Package of 10 plastic strip comprising 10 individual markers which can be placed for easy identification during the use of multiple units. CNL2 AGENCY APPROVALS Certification in accordance with: United States Standard for Industrial Control Equipment - UL 508 and Canadian Standard Association for Industrial Control Equipment C22.2 No. 14. DRH series conforms to the harmonized EN standard EN/IEC Electromagnetic Compatibility: IEC : Electrostatic Discharge Level 3 IEC : Electrically Fast Transients Level 3 IEC : Electrical Surges Level 3 Vibration Resistance: IEC : Amplitude Range Hz, Displacement 0.75mm Shock Resistance: IEC : Peak Acceleration 15g, Duration 11msec. E GENERAL NOTES (1) All parameters at 25 C unless otherwise specified. (2) Relay will self trigger between V, Not suitable for capacitive loads. (3) Mounted in the Vertical position. (4) Turn-on time for Instantaneous turn-on version is 4 msec. (5) For input to alarm output the dielectric strength is 1.5kV. (6) UL approval up to 40 C surrounding temperature. (7) 100kA, 480VAC, when protected with CC class fuses rated 600VAC, 20A or equivalent. (8) IP20 rating is not associated with the UL approval. (9) Minimum spacing to obtain max. current is 22mm between adjacent units. (10) Combination of these Protective Devices and have not been evaluated by UL. Rev

7 DANGER / PELIGRO / DANGER /GEFAHR / PERICOLO / 危险 HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH. Disconnect all power before installing or working with this equipment. Verify all connections and replace all covers before turning on power. Failure to follow these instructions will result in death or serious injury. RIESGO DE DESCARGA ELECTRICA O EXPLOSION. Desconectar todos los suministros de energia a este equipo antes de trabajar con este equipo. Verificar todas las conexiones y colocar todas las tapas antes de energizer el equipo. El incumplimiento de estas instrucciones puede provocar la muerte o lesiones serias. RISQUE DE DESCHARGE ELECTRIQUE OU EXPLOSION Eteindre toutes les sources d'énergie de cet appareil avant de travailler dessus de cet appareil Vérifier tous connections, et remettre tous couverts en olace avant de mettre sous De non-suivi de ces instructions provoquera la mort ou des lésions sérieuses sérieuses. GEFAHR EINES ELEKTRISCHE N SCHLAGES ODER EINER EXPLOSION. Stellen Sie jeglichen Strom ab, der dieses Gerät versorgt, bevor Sie an dem Gerät Arbeiten durchführen Vor dem Drehen auf Energie alle Anschlüsse überprüfen und alle Abdeckungen ersetzen. Unterlassung dieser Anweisungen können zum Tode oder zu schweren Verletzungen führen. RISCHIO DI SCOSSA ELETTRICA O DELL ESPLOSIONE. Spenga tutta l'alimentazione che fornisce questa apparecchiatura prima di lavorare a questa apparecchiatura Verificare tutti i collegamenti e sostituire tutte le coperture prima dell accensione L'omissione di queste istruzioni provocherà la morte o lesioni serie 存在电击 爆炸或电弧闪烁危险 在操作此设备之前请先关闭电源 若不遵守这些说明, 可能会导致严重的人身伤害甚至死亡 WARNING / AVERTISSEMENT / WARNUNG /ADVERTENCIA / AVVERTENZA / RISK OF MATERIAL DAMAGE AND HOT ENCLOSURE The product's side panels may be hot, allow the product to cool before touching. Follow proper mounting instructions including torque values. Do not allow liquids or foreign objects to enter this product. Failure to follow these instructions can result in serious injury, or equipment damage. RIESGO DE DAÑOS MATERIALES Y DE SOBRECALENTAMIENTO DE LA UNIDAD Los paneles laterales del producto pueden estar calientes. Esperar que el producto se enfríe antes de tocarlo. Respetar las instrucciones de montaje, y en particular los pares de apretado. No dejar que penetren líquidos o cuerpos extraños en el producto. Si no se respetan estas precauciones pueden producirse graves lesiones, daños materiales. RISQUE DE DOMMAGE MATERIEL ET DE SURCHAUFFE DU BOITIER Les panneaux latéraux du produit peuvent être chauds. Laisser le produit refroidir avant de le toucher. Respecter les consignes de montage, et notamment les couples de serrage. Ne pas laisser pénétrer de liquide ni de corps étrangers à l'intérieur du produit. Le non-respect de cette directive peut entraîner, des lésions corporelles graves ou des dommages matériels. RISCHIO DI DANNI MATERIALI E D'INVOLUCRO CALDO I pannelli laterali dell'apparecchio possono scottare; lasciar quindi raffreddare il prodotto prima di toccarlo. Seguire le istruzioni di montaggio corrette. Non far entrare liquidi o oggetti estranei in questo apparecchio. La mancata osservanza di questa precauzione può causare gravi rischi per l'incolumità personale o danni alle apparecchiature. GEFAHR VON MATERIALSCHÄDEN UND GEHÄUSEERHITZUNG Die Seitenwände können heiß sein. Lassen Sie das Produkt abkühlen, bevor Sie es berühren. Beachten Sie die Montageanweisungen, Führen Sie keine Flüssigkeiten oder Fremdkörper in das Produkt ein. Die Nichtbeachtung dieser Anweisung kann Körperverletzung oder Materialschäden zur Folge haben. 材料损坏和高温外壳的危险性 产品的一侧面板可能很热, 在其冷却前请不要触碰 遵照正确的安装说明, 包括扭矩值 请勿让液体及其他异物进入本产品 如不能正确执行这些操作说明, 极有可能造成严重人体伤害或者设备的损坏

8 ANNEX - ENVIROMENTAL INFORMATION The environmental information disclosed in this annex including the EIP Pollution logo are in compliance with People s Republic of China Electronic Industry Standard SJ/T , Marking for Control of Pollution Caused by Electronic Information Products. Part Name Toxic or hazardous Substance and Elements Lead Mercury Cadmium Hexavalent Polybrominated Polybrominated (Pb) (Hg) (Cd) Chromium biphenyls diphenyl ethers (Cr (VI)) (PBB) (PBDE) Semiconductor die Solder 部件有毒有害物质或元素名称铅汞镉六价铬多溴联苯多溴二苯醚 半导体芯片焊接点 (Pb) (Hg) (Cd) (Cr (VI)) (PBB) (PBDE) 50