420 Third Street Piqua, Ohio 436-0603 www.pumpagents.com PumpAgents.com - Click here for Pricing/Ordering SERIES: WG6-2 SECTION 4A PAGE ISSUED 2/03 REPLACES 2/0 SELF-PRIMING CENTRIFUGAL PUMPS 300RPM - 60Hz. CAPACITIES TO 280GPM (7.7LPS) HEADS TO 78 FEET (4.3M) FEATURES CASING Casing is close grain iron of 30,000 psi minimum tensile strength. Back pull-out design eliminates the need to disturb piping should the pump ever require service the casing stays in the line. ENCLOSED BRONZE IMPELLER Enclosed Bronze Impeller is of the latest hydraulic design for maximum efficiency. It is balanced for vibration-free operation. It is precision fit to shaft with key drive and cap screw lock. MECHANICAL SHAFT SEAL Standard self-adjusting shaft seal for temperatures up to 22 F (07 C) and pressures to 0 psi (034kpa). Ceramic seat and carbon seal face for long trouble-free service. Special seals are available for higher temperatures and fluids other than water. JM Type motors have NEMA standard mounting flange, extended steel shaft and dual bearings. These motors offer the advantage of quiet operation, controlled shaft deflection for longer seal life, and bearings sized to provide good service life. All motors are supplied by manufactures with national field service facilities. Flapper and check valves on the suction pipe are not required, but are recommended. BRONZE SHAFT SLEEVE Gasketed and keyed hook-type sleeve protects shaft from wear and corrosion in seal area. FACTORY TESTED After careful assembly and inspection, EVERY pump is factory tested and will meet Hydraulic Institute standards. MAXIMUM OPERATING CONDITIONS TEMPERATURE 22 F (07 C) (For Standard Buna-N Seal) INLET PRESSURE 00 PSI (690kpa) CASING WORKING PRESSURE 200 PSI (379kpa) MOTOR INFORMATION 60 Hz - - ODP :, 7-/2 & 0 Hp. - 230/460 Volt Voltages may differ from some suppliers. Consult factory. Overload Protection: All motors must be installed with a magnetic starter which provides full 3-leg protection. Failure to use correct starter and overloads will void motor warranty. MATERIALS OF CONSTRUCTION ALL IRON BRONZE FITTED Adapter Cast Iron Cast Iron Casing Cast Iron Cast Iron Casing Wear Ring Steel Bronze Shaft #36 Stainless #36 Stainless Impeller Cast Iron Bronze Shaft Seal Carbon-Ceramic S. Steel-Buna-N Carbon-Ceramic S. Steel-Buna-N PUMPS & SYSTEMS A Crane Co. Company
SECTION 4A PAGE 2 ISSUED 6/03 REPLACES 2/03 420 Third Street Piqua, Ohio 436-0603 END SUCTION CENTRIFUGAL PUMPS MODEL 3 PHASE Motor Frame Size DISC. SUCT. DIMENSIONS IN INCHES A AB B CP D DD E F G H L O S X Y 30WG6-2 82JM 2 2 8 3 / 4 9 / 6 3 / 4 2 / 6 4 / 2 6 / 2 3 3 / 4 2 / 4 / 2 3 / 32 4 9 / 6 6 / 6 9 6 / 6 37WG6-2 7 /2 84JM 2 2 8 3 /4 9 /6 6 3 /4 23 /6 4 /2 6 /2 3 3 /4 2 3 /4 300WG6-2 0 23JM 2 2 0 3 /8 0 7 /8 7 3 /4 24 3 /6 /4 6 /2 4 /4 2 3 /4 /2 3 /32 4 9 /6 6 /6 9 6 /6 /8 3 /32 4 7 /8 6 /6 9 6 /6 MODEL 3 PHASE Motor Frame Size DISC. inch SUCT. inch DIMENSIONS IN MILLIMETERS A AB B CP D DD E F G H L O S X Y 30WG6-2 82JM 2 2 222 246 46 4 6 9 7 3 0 36 246 60 229 4 37WG6-2 7 / 2 84JM 2 2 222 246 7 602 4 6 9 70 3 0 36 246 60 229 4 300WG6-2 0 23JM 2 2 264 276 97 64 33 6 08 70 6 0 378 279 60 229 4 Dimensions shown above are approximate maximum dimensions for standard pumps equipped with open drip-proof motors, DO NOT USE FOR CONSTRUCTION PURPOSES. CERTIFIED DRAWINGS AVAILABLE ON REQUEST. PUMPS & SYSTEMS A Crane Co. Company
CSPP-60 RPM & PHASE - MOTORS OPEN DRIP PROOF FRAME SIZE Single Phase (ODP) 09902 280 84JM 23JM (ODP) 09906 09907 09999 0 82JM 84JM 23JM TOTALLY ENCLOSED (TEFC) 0990 099 20000 0 84JM 23JM 2JM EXPLOSION PROOF (XP) 0994 099 2000 0 84JM 23JM 2JM SERIES: WG6-2 SELF-PRIMING CENTRIFUGAL PUMPS File: WG6-200.dwg
SYMBOL * QUANTITY DESCRIPTION 2 22063-C Shaft Sleeve, Bronze 3 04236 Plug, /4-8 - Bronze 4 0928 4 Cap Screw - 3/8-6 x " Lg. (992 Adapter) -68-6 4 Cap Screw - /2-3 x -/4" Lg. (9920 Adapter) -23-6 8 Nut - 3/8-6 6 0307 8 Stud - 3/8-6 x -3/4" Lg. 7 0609-A 8 Washer 8 0992 Adapter, Iron, 82-84 JM Frames 09920 Adapter, Iron, 23-2 JM Frames 9 2323- Casing Assy., Iron w/brz. Wear ring - & 2323 Casing Assy., Iron - 0 0 0294 Plug, --/2 - Sq Hd., Bronze 2304 Key - 3/6 Sq. x -/2" Lg. 2 928-A Cap Screw - 3/8-6 x Lg., S.S. 3 22080 2208 22082 22093 4 2326 Wear Ring, Bronze (2323- Casing Assy) 220-C Washer, Bronze - Impeller Retaining 6 7 8 22083 22084 2208 22094 20420-6.06 09928-6.2 09929-6.2 22099 23000 23002 2300 2 Impeller, Bronze - Impeller, Bronze - Impeller, Bronze - 0 0997 Mechanical Seal - Buna N 9 09926 227 Mechanical Seal - Viton Mechanical Seal - EPDM** 20 0998 Slinger Washer 2 0027 2 Plug, Sq. Hd., Iron SYMBOL 8 0992-B * 9 2323-A- * ** QUANTITY DESCRIPTION DIFFERING S FOR ALL BRONZE CONSTRUCTION Adapter, Brz., 82-84JM Frames 09920-B Adapter, Brz., 23-2JM Frames Casing Assy., Brz w/brz. Wear Ring - & 2323-A Casing, Bronze 2 03289 Cap Screw, 3/8-6 x " Lg., Bronze DIFFERING S FOR ALL IRON CONSTRUCTION 2 22063-A Shaft Sleeve, Stainless Steel 3 9 0 04236-A 2323-B- 2649 Plug, /4-8, Stainless Steel Casing Assy, Iron w/steel wear ring - & Plug --/2 - Sq Hd., Iron 4 7 2326-A 220-A 20420-A-6.06 09928-A-6.2 Wear Ring, Steel (2323-B- Casing Assy) Washer, Steel - Impeller Retaining Impeller, Iron - Impeller, Iron - 09929-A-6.2 Impeller, Iron - 0 ** Size suffixes same as standard bronze impellers. CSPP-6 SERIES: WG6-2 * Casing Assy. Includes Symbol 4. 23270-, -A-, -B- ( & ) are complete casing assemblies consisting of symbols 6, 9, 0, 4 & 2. 23270, -A (0) are complete casing assemblies consisting of symbols 6, 9, 0 & 2.
For technical advice or service please take your pump into your local pump service center. To order pump or parts or for pricing please go to the following links : Burks Pumps Home >> Burks Pumps stock list >>