Filtration Range Tube Technology Range Diagtronics Range Catalogue 11 STAUFF Hire 1
Index Introduction 4 Filtration Range 5-9 Tube Technology Range 10-16 Diagtronics Range 17-19 3
Introduction STAUFF Hire The STAUFF Hire programme offers an extensive range of Filtration Range Diagtronics Range specialised equipment for pipework installations, flushing The STAUFF Hire range of filtration equipment provides STAUFF Hire offers diagnostic equipment for the simultaneous and filtration of oil systems and diagnostic measurement flexible solutions for the removal of water, solids, and measurement of flow, pressure, temperature and speed in by contractors and service providers to the hydraulic and oxidation-varnish from oils. Each system is variable to the hydraulic systems. lubrication industries. application and the equipment is therefore customised to These robust units are available in either Analogue or Digital your specific requirement. versions. STAUFF Hire is available for daily, weekly, monthly or long term hire periods. Tube Technology Range The STAUFF Hire range of Tube Technology equipment provides flexible options for the processing of steel and stainless steel tubes. The range of portable and table top equipment available for hire varies from weldless end-forming, pre-assembly of cutting rings, flaring, deburring and manual hand bender. 4
Filtration Range Desorber D10 6 Filter Separator & Fine Filter PTU3-27/108 7 Filter Separator PTU2-27/54 7 Filter Separator PTU2-27/27 8 Fine Filter HDU 27/54 8 Filter Cart SPFC 9 Hi-flow Gear Oil Filter Cart SCFC 9 5
Filtration Range Desorber D10 The Desorber D10 hire unit is designed to remove water from oil through a patented desorption principle. The desorption process is based on the principle that heated air can effectively hold large quantities of water. In the Desorber, oil preheated to 60 C is met by a counter flow of cold, dry air. Heated very quickly by the hot oil, the air will absorb any water present until saturation is reached. The Desorber D10 is unaffected by viscosity - range ISO VG 32-150 and additive packages. The Desorber treats mineral oils as well as synthetic fluids, and stable emulsions. The Desorber can dry oil down to a water content of < 200 ppm, removing 0.2 litres of water per hour, depending on the oil type. small to medium size systems up to 2000 Litres Hydraulic systems Lubrication systems Synthetic fluid systems Gear boxes with small volumes Contaminant Removal: Oil Type: Element: Weekly / Monthly 100 kg Water All Types of Oils Not Required Removes water even from emulsified oil Extends the lifetime of both oil and system Prevents uncontrolled breakdowns Reduces maintenance costs Easy to connect and operate 6
Filtration Range Combined Filtration Unit (Filter Separator & Fine Filter) PTU3-27/108 - Portable The PTU3 Filter Separator is a portable off-line oil filtration system / oil separator, combining fine filtration with water separation all in one unit, with an integrated variable speed driven circulating pump. They are designed for use in applications containing hydraulic oil, diesel fuel, lubrication oil, and others, in which water condensation or ingress is a constant or recurrent problem. Contaminant Removal: Element: 400 kg Water, Solids, Varnish Selection on application It can also be customised to function as a Filter Separator removing water by coalescence, while at the same time minimize oil contamination levels of particles and oil degradation products (oxidation resin/sludge, varnish). The same unit can be converted to function as a Fine Filter, ideal for controlling oil contamination levels of particles, water and degradation products (oxidation resin/sludge, varnish). systems to 20,000 Litres Filter Separator mode: Hydraulic oils (e.g., reservoirs) Boiler feed pumps Steam turbine lubrication oils Gearboxes with potential water ingress (e.g., wet crushers or marine thrusters) Lubrication oil for industrial and marine applications where water ingress is a recurrent problem Fine Filter mode: Hydraulic systems (e.g., test benches, power packs for cranes, presses etc.) Lubrication systems (e.g., for bearings, gears etc.) Marine diesel engine lubrication Quench works and similar industrial and marine applications Extends the lifetime of both oil and system Prevents uncontrolled break downs reduces maintenance costs Easy to connect and operate Combined Filtration Unit (Filter Separator & Fine Filter) PTU3 27/54 - Portable The PTU3 Filter Separator is a portable off-line oil filtration system / oil separator, combining fine filtration with water separation all in one unit, with an integrated variable speed driven circulating pump. They are designed for use in applications containing hydraulic oil, diesel fuel, lubrication oil, and others, in which water condensation or ingress is a constant or recurrent problem. It can also be customised to function as a Filter Separator removing water by coalescence, while at the same time minimize oil contamination levels of particles and oil degradation products (oxidation resin/sludge, varnish). The same unit can be converted to function as a Fine Filter, ideal for controlling oil contamination levels of particles, water and degradation products (oxidation resin/sludge, varnish). Contaminant Removal: Element: 220 kg Water, Solids, Varnish Selection on application Extends the lifetime of both oil and system Prevents uncontrolled breakdowns Reduces maintenance costs Easy to connect and operate systems to 10,000 Litres Filter Separator mode: Hydraulic oils (e.g., reservoirs) Boiler feed pumps Steam turbine lubrication oils Gearboxes with potential water ingress (e.g., wet crushers or marine thrusters) Lubrication oil for industrial and marine applications where water ingress is a recurrent problem Fine Filter mode: Hydraulic systems (e.g., test benches, power packs for cranes, presses etc.) Lubrication systems (e.g., for bearings, gears etc.) Marine diesel engine lubrication Quench works and similar industrial and marine applications 7
Filtration Range Filter Separator PTU2 27/27 - Portable The PTU2 Filter Separator is a portable off-line oil filtration system / oil separator, combining fine filtration with water separation all in one unit, with an integrated variable speed driven circulating pump. The unit is designed for use in applications containing hydraulic oil, diesel fuel, lubrication oil, and more, in which water ingress is a constant / recurrent problem. Filter Separators remove water by coalescence and at the same time minimize oil contamination levels of particles and oil degradation products (oxidation resin/sludge, varnish). systems up to 3000 Litres Hydraulic systems Lubrication systems Marine diesel fuel systems Steam turbine lube systems Water-cooled hydraulic industry equipment. Contaminant Removal: Element: 120 kg Water, Solids, Varnish Selection on application Removes water even from emulsified oil Extends the lifetime of both oil and system Prevents uncontrolled breakdowns Reduces maintenance costs Easy to connect and operate Fine Filter HDU 27/54 - Portable The HDU Fine Filter portable hire unit is an offline oil filtration system with integrated circulating pumps for off-line installation. The filter is a highly efficient purification system for applications involving hydraulic oil, lubrication oil, gear oil, quenching oil, phosphate esters and more. The Fine Filter is ideal for controlling oil contamination levels of particles, water and degradation products (oxidation resin/sludge, varnish). systems up to 5000 Litres Hydraulic systems (e.g., test benches, power packs for cranes, presses etc.) Lubrication systems (e.g., for bearings, gears etc.) Marine diesel engine lubrication Small industrial and marine applications Contaminant Removal: Element: 120 kg Water, Solids, Varnish Selection on application Extends the lifetime of both oil and system Prevents uncontrolled breakdowns Reduces maintenance costs Easy to connect and operate 8
Filtration Range Filter Cart - SPFC - Portable The SPFC Filter Cart is a very complete and practical unit utilising the magnetic core prefiltration and final filtration through a 10 micron absolute element. This cart is designed for transfer, filling, emptying reservoirs with filtration of mineral oil based fluids for hydraulic systems & gearboxes limited to a viscosity range of 10-150 centistokes. The SPFC offers excellent mobility for maintenance, resulting in clean oil changes, improved component lifetime, and ultimately increased equipment up-time. Hydraulic systems (test benches, power packs for mobile equipment, cranes, presses etc.) Lubrication systems (bearings, gears etc.) Similar light industrial applications Contaminant Removal: Element: 53 kg Solids Included Extends the lifetime of both oil and system Prevents uncontrolled breakdowns Reduces maintenance costs Easy to connect and operate Hi-flow Gear Oil Filter Cart - SCFC - Portable The SPFC Filter is a very complete and practical unit utilising the magnetic core pre-filtration and final filtration through 4 x 25 micron absolute elements. This cart is designed for transfer, filling, emptying reservoirs with filtration of mineral oil based fluids for hydraulic systems & gearboxes limited to a viscosity range of 10-1000 centistokes. Hydraulic systems (test benches, power packs for mobile equipment, cranes, presses etc.) Lubrication systems (bearings, gears etc.) Similar light industrial applications Extends the lifetime of both oil and system Prevents uncontrolled breakdowns Reduces maintenance costs Easy to connect and operate Contaminant Removal: Element: Dry Weight 155 kg Solids 4 x 25micron Spin On Cans 1 x Magnetic Core Suction Filter 9
Filtration Range 10
Tube Technology Range STAUFF Press Pre-Assembly and Flare Machine 12 STAUFF Press Manual Hand Pump 13 STAUFF Press Cutting Ring Pre-Assembly and Final Assembly Machine 14 STAUFF Form Tube Forming Machine 15 STAUFF Deburr Unit 16 STAUFF Manual Tube Bender 16 11
Tube Technology Range STAUFF PRESS - Portable The STAUFF PRESS automatic flare & pre-assembly unit is designed for leak free assembly of flaring or cutting ring fittings on tube or hose ends with minimum training of operators. Compact and rugged table-top unit for mobile and flexible use Very well suited for both, assembly of cutting rings and flaring (37 JIC) Pressure table allows for selecting the specific hydraulic pressure (according to the tube diameter and end form method required) Manual pressure adjustment with digital display Short assembly and set-up times when changing tube diameter or end form method 65 kg Two end form systems available: Flaring: Ø 1/4-1 ½ O.D. Pre-assembly: Ø 6-42 mm O.D. All types of on-site tube installations and repairs Steel & stainless steel tube Precise Portable Reduces installation costs Time saving Easy to operate STAUFF PRESS - Tooling Choice of attachments 1. Attachment for 37 JIC flared couplings 2. Attachment for cutting ring assembly Dies: Metric: Ø6-42 mm O.D. Imperial: Ø 1/4-1 ½ O.D. Flaring Pre-assembly Flaring: Pre-assembly: One piece Two pieces 12
Tube Technology Range STAUFF PRESS - Manual Hand Pump The STAUFF PRESS - Manual Hand Pump pre-assembly device consists of a hand-pump pressure unit with a working piston and a pushing head. For assembly, one tool set is required per tube outside diameter. The assembly is carried out by pumping the assembly lever. The correct pre-assembly is determined by the required pressure displayed on the pressure gauge. As a manual device it can be used on site. However, for frequent assemblies, clamping in a vice is recommended. All types of on-site tube installations and repairs Suitable for Steel & Stainless Tube Precise Portable Reduces installation costs Time saving Easy to operate 14 kg STAUFF PRESS - Manual Hand Pump - Tooling Suitable for the pre-assembly of: ES-4 cutting rings with sealings for a Ø 6-42 mm O.D 2S cutting rings for Ø 6-42 mm O.D BV-10 flared cones (weld cone repair system) for Ø 6-42 mm O.D All other cutting rings in accordance with the valid standards (DIN EN ISO 8434-1) Dies to suit Metric: Ø6-42 mm O.D & Imperial Ø 1/4-1 ½ O.D Flare: Pre-assembly: BV 10: Two pieces Two pieces Flare Cone & Jaw 13
Tube Technology Range STAUFF Press Pre-Assembly and Final Assembly Machine The STAUFF Press Assembly Machine SPR-PRC-POC allows the pressure/position-controlled pre-assembly and final assembly of cutting rings from the Extra-Light Series (LL), the Light Series (L) and the Heavy Series (S) according to ISO 8434-1 / DIN 2353 on tube ends with outer diameters between 4 mm and 42 mm. The machine is designed as a robust table-top device for continuous operation in the workshop. It is used in connection with hardened and wear-resistant assembly studs FI-MFK and support plates FI-GP which are specially designed for the machine assisted assembly. The STAUFF Press pre-assembly and final assembly machine can be operated wherever an electrical connection with 400 V AC/16 A/50 Hz is available. All on-site tube installations Suitable for use with Steel or Stainless Steel tubes Precise Portable Reduces installation costs Time saving Easy to operate 95 kg STAUFF Press Pre-Assembly and Final Assembly Machine Tooling Tooling consists of: - Wear-resistant assembly stud FI-MFK - Support plate FI-GP with RFID transponder Suitable for use with Steel and Stainless Steel tubes Fitting and sealing to suit is available for all sizes from STAUFF. Series and diameters: Extra-Light Series (LL): 4, 6, 8, 10, 12 mm Light Series (L): 6, 8, 10, 12, 15, 18, 22, 28, 35, 42 mm Heavy Series (S): 6, 8, 10, 12, 14, 16, 20, 25, 30, 38 mm 14
Tube Technology Range STAUFF Form Tube Forming Machine The type SFO-F tube forming machine facilitates the economical and most reliable production of tube ends made of steel, stainless steel and other materials with a contour typical for the STAUFF Form tube forming system. The machine is designed as a robust table-top device for continuous operation in the workshop. It is used in connection with FI-FST tube shapers and FI-FB clamping jaws. Tube shapers with FI-ID internal tube supports are used with selected tube dimensions, which prevent the tube from being constricted in the shaping area. The STAUFF Form machine can be operated wherever an electrical connection with 400 V AC/16 A/50 Hz is available. The device is equipped with a forming force and is easily manoeuvred using the handle provided. All types of on-site tube installations and repairs Precise Portable Reduces installation costs Time saving Easy to operate 210 kg STAUFF Form Tube Forming Machine Tooling Tooling consists of: - Tube Shaper FI-FST with clear identification of the tube dimensions* - Version of a Tube Shaper FI-FST with Internal Tube Support FI-ID** - Clamping Jaws FI-FB with clear identification of the tube dimension ** * Suitable for use with Steel and Stainless Steel tubes. DIN Metric fittings to DIN 2353 and sealing rings to suit are available for all sizes from STAUFF. Series and dimensions: Light Series (L): 6 x 1,5 mm to 42 x 4 mm Heavy Series (S): 6 x 1,5 mm to 38 x 6 mm 15
Tube Technology Range STAUFF DEBURR - Portable The STAUFF DEBURR unit is a portable table top machine for internal and external deburring of tube ends. Proper connection and assembly of hydraulic lines demands clean deburring of tube ends to prepare the tube end for the pre-assembly of a cutting ring or flare, ensuring highest quality finished tube. 25 kg Tubes of all materials and quality grades are easily deburred within seconds. By pressing the end of the tube to the special tools made from high speed steel, the tube end if cleaned and any superfluous metal swarf from the inner and outer tube is thoroughly removed and collected in the integrated collecting box. This small, lightweight and robust machine is powered by an electric motor 415V/50Hz. Due to the fixed rotation speed of the tools, it guarantees long service life and almost mark-free deburring. Suitable for use with steel and stainless steel tube. All types of on-site tube & pipe installations and repairs Precise Portable Reduces installation costs Time saving Easy to operate STAUFF Manual Tube Bender - Portable The STAUFF Manual Tube Bending Kit is vice mounted bending kit suitable for bending tube below 22 mm O.D. Dies matched to the outside diameter of the tube provide an accurate bend radius which is determined by the scale indicator printed on each bend die. No mandrel required. The Manual Tube Bending Kit has the reliability and flexibility required for any small installation project or repair. Bend Dies included suit metric Ø6-22 mm O.D & Imperial 1/4-3/4 O.D. Suitable for use with steel and stainless steel tubes All types of on-site tube & pipe installations and repairs Custom fuel, brake, and hydraulic lines, small diameter chassis tubing Precise Portable Reduces installation costs Time saving Easy to operate Bend Dies: 5 kg Included 16
Diagtronics Range Analogue Hydraulic Tester 18 Digital Hydraulic Tester 18 Digital Hydraulic Multimeter 19 17
Diagtronics Range Analogue Hydraulic Tester - FTM400R Mining Underground The Analogue Hydraulic Tester measures all three basic parameters: flow, pressure and temperature in a hydraulic system. Suitable for fault-finding and checking performance of equipment, saves hours of guess-work and reduces down time. 15 kg Capacities - Flow: 378 lpm (100 US GPM) Pressure: 420 bar (6000PSI) Accuracy better than +/- 4% of full scale Temperature range 0-116 C (0-240 F) Built-in INTERPASS protection against pressure overload. (safety burst discs included) Flow meter has a dual scale calibrated in both LPM and GPM (Imperial) Pressure gauge is dual scale, 0-400/6000 bar/psi liquid filled for fast reliable reading of fluctuating pressures Can be connected In Line between the pump and valve for convenient machine testing Heat stressed hydraulic fluids can be a major factor in component failure. The thermometer is dual scale C and F is a carefully designed and integrated part of a high quality unit. No electrical components No aluminium components Suitable for Underground Coal and Hard Rock mining equipment Precise Portable Reduces maintenance costs Time saving Easy to operate Digital Hydraulic Multimeter - DHT401 The Digital Hydraulic Multimeter can simultaneously read flow, pressure, temperature and speed, and are also capable of reading drive shaft speed. Bi-Directional loading valve for quick simulation of machine operating loads Built-in INTERPASS protection against pressure overload, safety burst discs fitted Measure flow, pressure and temperature External speed input Simulate machine performance using loading valve Suitable for mobile construction and surface mining equipment, and industrial hydraulic applications Precise Portable Reduces maintenance costs Time saving Easy to operate 12 kg 18
Diagtronics Range Digital Hydraulic Multimeter - DHM803 The Digital Hydraulic Multimeter can simultaneously read flow, pressure, temperature and speed, and are also capable of reading drive shaft speed. Bi-Directional loading valve for quick simulation of machine operating loads All digital display Built-in INTERPASS protection against pressure overload, safety burst discs fitted Measure flow, pressure and temperature External speed input Simulate machine performance using loading valve Suitable for mobile construction and surface mining equipment, and industrial hydraulic applications Precise Portable Reduces maintenance costs Time saving Easy to operate 12 kg 19
Catalogue 11 STAUFF Hire Germany Walter Stauffenberg GmbH & Co. KG Im Ehrenfeld 4 58791 Werdohl Tel.: +49 2392 91 60 Fax: +49 2392 91 61 60 E-Mail: sales@stauff.com STAUFF products and services are globally available through wholly-owned subsidiaries and a tight network of authorised distributors and representatives in all major industrial regions of the world. You can find detailed contact information on the last two pages of this product catalogue or at Adelaide Auckland Brisbane Melbourne Sydney Wollongong SA Australia E: sant.sales@stauff.com.au New Zealand E: sales@stauff.co.nz QLD Australia E: qld.sales@stauff.com.au VIC Australia E: vic.sales@stauff.com.au NSW Australia E: nsw.sales@stauff.com.au NSW Australia E: sales@stauff.com.au Catalogue 11 STAUFF Hire English 06/2018 20