ROSS CONTROLS. Double Valves for Clutch/Brake Control

ROSS CONTROLS Double Valves for Clutch/rake Control DM Series D and 5 Series

Contents ge DM Series Double Valves for Control Reliable Energy Isolation. -.8 With Dynamic Monitoring & Memory DM Series D SERPR Double Valves 5 Series with L- Monitor with E-P Monitor with D-S Monitor. -.0 SERPR Crossflow Double Valves 5 Series with Pressure Switches without Pressure Switches. -.9 Explosion Proof Valves for Clutch/rake Control Consult ROSS utomatic Systems Consult ROSS Modular ir Distribution Consult ROSS utomation Valves Consult ROSS Cautions and Warranty Compatible Lubricants Cautions and Warnings Inside Cover 0.

DM Series D Double Valves SERPR 5 Series Double Valves SERPR Crossflow 5 Series Double Valves VLVE SERIES asic Size VILLE PORT SIZES MX. FLOW Cv Reset Port Size / /8 / / / / / /8 / / / / Manual Remote Solenoid ge DM D with Total Dynamic Monitoring & Complete Memory DM D,, 8.7.7.8.6.6. -.6 DM D, 0 8.86 0.. -.6 DM D Series E & C Preassembled Wiring Kits.7 ccessories.8 5 SERPR L- Monitor E-P Monitor D-S Monitor 5 SERPR Crossflow With or Without Pressure Switches With Pressure Switches. -. 8.5.5 -.6 8 8.5 9.5 -.6 0 0.0.5 -.6 8.5.7 -.8 8 8.5 9.7 -.8 0 0.7 -.8 8.5.9 -.0 8 8.5 9.9 -.0 0 0.9 -.0 0.9.. -..7..5 -.6.7 8.5.8 -.9 8 8.5 9.8 -.9 0 0.8 -.9

ROSS CONTROLS Double Valves Control Reliable for Clutch/rake Control DM Series D

DM Monitoring: The DM is a patented / normally closed valve (with an intermediate, lockout position) distinguished by SERPR Crossflow passages with poppet and spool valving on the main valve stems. This arrangement provides the valve s outstanding flow characteristics and an integrated monitoring capability with total memory. The valve provides dynamic monitoring and dynamic memory. Dynamic Monitoring means that all monitoring components change state on every valve cycle. Should the valve elements cycle asynchronously, the valve will exhaust downstream air and lock-out, prohibiting further operation. Dynamic Memory within a monitoring system indicates that when a valve lock-out occurs, the valve will retain the fault information regardless of air or electrical changes. The DM system can only be reset by a defined operation/procedure, and will not self-reset (turning the valve off and on) or reset when inlet air supply is removed and re-applied. Such automatic resetting would conceal potential hazards from the operator. Explosion-Proof solenoid pilot valves available, consult ROSS. VILLE PORT SIZES MX. FLOW Cv Reset VLVE SERIES / /8 / / / Port Size / /8 / / / Manual Remote Solenoid ge DM D.7.7.8.6.6 8.86 0.. -.6 DM D Series E & C Preassembled Wiring Kits.7 ccessories.8

Control Reliable Double Valves DM Series D Self Monitored - Clutch/rake Control asic Size,, 8, and 0 Dynamic Monitoring With Complete Memory: Memory, monitoring, and air flow control functions are simply integrated into two identical valve elements. Valves lock-out due to asynchronous movement of valve elements during actuation or de-actuation, resulting in a residual outlet pressure of less than % of supply. Overt action is required for reset cannot be reset by removing and re-applying supply pressure. Reset can only be accomplished by remote air signal, optional electrical solenoid reset signal, or optional manual reset. asic / Normally Closed Valve Function: Dirt tolerant, wear compensating poppet design for quick response and high flow capacity. PTFE back-up rings on pistons to enhance valve endurance operates with or without inline lubrication. Status Indicator (Optional): Includes a pressure switch with both normally open and normally closed contacts to provide status feedback to the press control system indicating whether the valve is in the lockout or ready-torun condition. The Status Indicator can be ordered installed or purchased separately and added to any DM base. Silencers: ll models include high flow, clog resistant silencers. Mounting: ase mounted with SPP or NPT pipe threads. Inlet and outlet ports on both sides provide for flexible piping (plugs for unused ports included). Captive valve-to-base mounting screws. asic Size and 0 Intermediate Pilots: Increases pilot air flow for fast valve response, making it possible to use the same size solenoids as valve sizes, & 8, thereby reducing electrical power requirements for these larger valves. THRED SPP D NPT N N/ (no base) X HOW TO ORDER (Choose your options (in red) to configure your valve model number.) DMD D REVISION LEVEL Size, 8,, 0 Size SIC SIZE 8 5 6 0 8 SE PORT SIZE / inlet / outlet 0 /8 inlet /8 outlet / inlet / outlet / inlet / outlet 8 / inlet / outlet inlet outlet 5 inlet outlet 6 inlet / outlet 7 0 / inlet - outlet 8 Valve Only (less base) X RESET TYPE Remote Solenoid Manual with Total Dynamic Monitoring & Complete Memory STTUS INDICTOR Yes No X Voltage* volts DC 0 volts C, 50 Hz; 0 volts C, 50/60 Hz 0 volts C, 50/60 Hz C** volts DC D volts C E * For other voltages consult ROSS. ** 0 VC not available in the U.S. (OSH regulations limit press control voltage to no more than 0 volts C). Simplified Schematic Connectors ordered separately, refer to page.8. For other options, consult ROSS. C V Valve asic Size - - Weight# lb (Kg).7.66 5 (.).80 6.70 6.0 (.8) 8.6.55 9. (.) 8.86 0.78 5.5 (7.) 0 0. 5.68.6 (.8) # Valve and base assembly with status indicator and solenoid reset. Construction: Dual poppet. Mounting Type: ase mounted. Pilot Solenoids: ccording to VDE 0580. Enclosure rating according to DIN 0050, IEC 6059 IP65. Two solenoids, rated for continuous duty (additional solenoid on optional reset). Standard Voltages/Pilot Solenoids Power Consumption (each solenoid): asic Size,,, 0: Primary and reset solenoids: volts DC; 0 volts C, 50 Hz; 0 volts C, 50/60 Hz. 5.8 watts nominal on C and DC 6.5 watts maximum on C and DC. asic Size 8: volts DC; 0 volts C, 50/60 Hz. Primary solenoids:5 watts on DC; 6 V inrush and.6 V holding on C. Reset solenoid: 6.0 watts on DC; 5.8 V inrush and 0. V holding on C. Electrical connection: DIN 650, Form. mbient Temperature: 5 to 0 F (-0 to 50 C). Media Temperature: 0 to 75 F ( to 80 C). Flow Media: Filtered, lubricated or unlubricated (mineral oils according to DIN 559, viscosity classes -6). STNDRD SPECIFICTIONS (for valves on this page): Inlet Pressure: asic Size : 5 to 50 psig (. to 0. bar). asic Size, 8,, 0: 0 to 0 psig (. to 8. bar). Reset Pressure: For remote air reset option must be equal to inlet pressure. Manual Pressure: Encapsulated, push button actuation. Pressure Switch (Status Indicator) Rating: Contacts - 5 amps at 50 volts C, or 5 amps at 0 volts DC. Monitoring: Dynamically, cyclically, internally during each actuating and de-actuating movement. Monitoring function has memory and requires an overt act to reset unit after lockout. Mounting orientation: Preferably horizontally (valve on top of base) or vertically (with pilot solenoids on top). Functional Safety Data: Category PL e; 0d: 0,000,000; PFHd: 7.7x0-9 ; MTTFd: 0.9 (n op : 6600). Certifications: CE Marked for applicable directives,, CS/UL, TSS for appropriately tested valves. Vibration/Impact Resistance: Tested to S EN 60068--7. IMPORTNT NOTE: Please read carefully and thoroughly all of the CUTIONS, WRNINS on the inside back cover..

Control Reliable Double Valves DM Series D Valve Technical Data Valve Dimensions inches (mm) SU-SE MODEL NUMERS and SU-SE SPECIFIC INFORMTION View X.79 (.6).50 (.) (ase mounting hole pattern) Valve Port Size Sub-ase Valve envelope Status Weight (ased in overall hole asic Model dimnsions at left.) Inlet Outlet Size Number Indicator lb (kg) asic Size asic Size.7 (88.79) 0.6 (6.) Outlet.9 (0.) 0.8 (0.9).7 (.9) Inlet 6.9 (76) 5.8 (.) View X (ase mounting hole pattern) Valve envelope (ased on overall dimensions at left.) 0.97 (.6) Outlet. (.5) Inlet. (.5) X 9.99 (5.8).00 (0.6) 7.7 (96.).99 (75.9).0 (5.9) 0.5 (6.) 0.95 (78.) 9. (9.8) 0. (5.6) ( places).00 (0.6).99 (75.9).00 (0.6).68 (9.7). (0.) 0.6 (.06).00 (0.6).0 (5.9) 0.6 (6.) with Solenoid Reset.7 (69.6) 0.5 (6.) 0.65 (6.6) / / 87C9 No.7 (0.8) / / 87C9 Yes. (.0) /8 /8 87C9 No.7 (0.8) /8 /8 875C9 Yes. (.0) / / 697C9 No.7 (0.8) / / 698C9 Yes. (.) / / 699C9 No.7 (0.8) / / 700C9 Yes. (.) 8 / / 70C9 No.6 (.6) 8 / / 70C9 Yes. (.9) 8 70C9 No.6 (.6) 8 70C9 Yes. (.9) 705C9 No 6. (.8) 706C9 Yes 6.8 (.) / 707C9 No 6. (.8) / 708C9 Yes 6.8 (.) 0 / 709C9 No.0 (5.) 0 / 70C9 Yes.6 (5.7) * NPT port threads. For SPP threads add a D prefix to the model number, e.g., D87C9. 8.7 (.7) 5.9 (50.88) View X (ase mounting hole pattern) Valve envelope (ased on overall dimensions at left.).60 (6.8) asic Size 8 Outlet Inlet.5 (9.).97 (50.0).8 (6.8) x.6 (8.5).7 (.) 0. (8.6) ( places) 0.6 (.06) 6. (58.).8 (08.7).68 (68.) 0.86 (.9).8 (86.9) 7.96 (0.80 View X (ase mounting hole pattern) Valve envelope (ased on overall dimensions at left.) 5.86 (8.8).67 (.).7 (8.) 0. (0.67) ( places) asic Size Outlet Inlet.6 (59.9).08 (5.8).0 (0.0) 7.7 (89.7) 0.57 (.8).7 (9.89).59 (0.) X.6 (0.9).70 97.) 9. (7.) View X (ase mounting hole pattern) Valve envelope (ased on overall dimensions at left.) 8.6 (.88) asic Size 0 Outlet.95 (9.5). (8.8).56 (65.0) 6.56 (0.6) 6.87 (8.5) 0.50 (.7) ( places).6 (9.6) 6. (55.96) 9.7 (7.) Inlet X. (6.5).7 (). 05, ROSS CONTROLS. ll Rights Reserved.

EXHUST OUTLET INLET EXHUST OUTLET INLET EXHUST OUTLET INLET Control Reliable Double Valves DM Series D Valve Operation Valve de-actuated (ready-to-run): The flow of inlet air pressure into the crossover passages is restricted by the size of the passage between the stem and the valve body opening. Flow is sufficient to quickly pressurize pilot supply/timing chambers and. The inlet poppets prevent air flow from crossover passages into the outlet chamber. ir pressure acting on the inlet poppets and return pistons securely hold the valve elements in the closed position. (ir passages shown out of position and reset adapter omitted for clarity. EXHUST OUTLET INLET Valve actuated: Energizing the pilot valves simultaneously applies pressure to both pistons, forcing the internal parts to move to their actuated (open) position, where inlet air flow to crossover passages is fully open, inlet poppets are fully open and exhaust poppets are fully closed. The outlet is then quickly pressurized, and pressure in the inlet, crossovers, outlet, and timing chambers are quickly equalized. De-energizing the pilots quickly causes the valve elements to return to the ready-to-run position. EXHUST OUTLET INLET Valve locked-out: Whenever the valve elements operate in a sufficiently asynchronous manner, either on actuation or de-actuation, the valve will move to a locked-out position. In the locked-out position, one crossover and its related timing chamber will be exhausted, and the other crossover and its related timing chamber will be fully pressurized. The valve element (side ) that is partially actuated has pilot air available to fully actuate it, but no air pressure on the return piston to fully de-actuate the valve element. ir pressure in the crossover acts on the differential of side stem diameters creating a latching force. Side is in a fully closed position, and has no pilot air available to actuate, but has full pressure on the inlet poppet and return piston to hold the element in the fully closed position. Inlet air flow on side into its crossover is restricted, and flows through the open inlet poppet on side, through the outlet into the exhaust port, and from the exhaust port to atmosphere. Residual pressure in the outlet is less than % of inlet pressure. The return springs are limited in travel, and can only return the valve elements to the intermediate (locked-out) position. Sufficient air pressure acting on the return pistons is needed to return the valve elements to a fully closed position. EXHUST OUTLET INLET Resetting the valve: The valve will remain in the locked-out position, even if the inlet air supply is removed and re-applied. remote reset signal (air or electric), or a manual push button actuation EXHUST must be applied to reset the valve. OUTLET Reset is accomplished by momentarily pressurizing the reset port. ctuation of the reset piston physically pushes the main valve elements to their closed position. Inlet INLET air fully pressurizes the crossovers and holds the inlet poppets on seat. ctuation of the reset piston opens the reset poppet, thereby, immediately exhausting pilot supply air, thus, preventing valve operation during reset. (Reset adapter added to illustration.) De-actuation of reset pistons causes the reset poppets to close and pilot supply to fully pressurize. Reset air pressure can be applied by a remote / normally closed valve, or from an optional / normally closed solenoid, or a manual push button mounted on the reset adapter. Status Indicator Pressure Switch Pilot booster on Size & 0 only Status Indicator: The status indicator pressure switch will actuate when the main valve is operating normally, and will de-actuate when the main valve is in the locked-out position or inlet pressure is removed. This device is not part of the valve lockout function, but, rather, only reports the status of the main valve. Status indicator (optional) in normal ready-to-run position. asic Size and 0 valves require relatively large pilots to actuate and de-actuate the main valve elements. In order to achieve extremely quick valve response for such large pilots, a -stage solenoid pilot system is incorporated into the design. This keeps the required electrical current to operate the pilots to a minimum. Reset Port Optional Reset Solenoid Valve asic Size & 0 pilots Schematic - Valve de-actuated.5

Control Reliable Double Valves DM Series D Valve Response Charts The charts below represent the fill and exhaust times for each of the various sizes of DM Series D double valves. The fill times were measured while raising (filling) the pressure in a volume from 0 to 0, 60, & 80 psi (0 to.,., & 5.5 bar) with a 90 psi (6. bar) inlet pressure. Conversely, the exhaust times were measured while lowering the pressure (exhausting) in a volume from 90 psi (6. bar) down to 90 to 60, 0, & 9 psi (.,., & 0.6 bar). Exhausting tests performed with silencer installed. Filling Exhausting asic Size 0.5 (5.5) 0.5 (0.5) 0.75 (5.75) (6) Volume litres (cubic inches) 0.5 (5.5) 0.5 (0.5) 0.75 (5.75) (6) Volume litres (cubic inches) asic Size Volume litres (cubic inches) Volume litres (cubic inches) asic Size 8 Volume litres (cubic inches) Volume litres (cubic inches) asic Size Volume litres (cubic inches) Volume litres (cubic inches) asic Size 0 Volume litres (cubic inches) Volume litres (cubic inches).6 05, ROSS CONTROLS. ll Rights Reserved.

Control Reliable Double Valves with Dynamic Monitoring & Memory DM Series D Preassembled Wiring Kits Preassembled Wiring Kits Kit Number* Length Solenoid Connector Lighted Connector meters Connector Type without Light Volts DC 0 Volts C (feet) 8H77 5H77-W 5H77-Z DIN 650 Form 5 (6.) 8H77 5H77-W 5H77-Z DIN 650 Form 0 (.8) 88H77** M Micro-DC 5 (6.) 89H77** M Micro-DC 0 (.8) * Each cable has one connector. **Coil includes light. Solenoid Cables with DIN Connector NOT USED RN PIN Solenoid Cables with M Connector LUE LCK LCK LUE RN LUE RN/YEL RY PIN RN/YEL ROUND Status Indicator Cable with DIN Connector RN/YEL ROUND RY RN LK RN LK RY These kits include cable for the status indicator, and cables with connector plus a cord grip for each. Wiring Kits with J-ox Kit Number* Connector Types Length meters (feet) 9H77 M - DIN (.) 50H77 M - M (.) * volts DC only. J-ox is a junction box with a 0-pin MINI connector for connecting to the user s control system and () 5-pin M ports for connecting to the solenoids and the status indicator on the DM Series valve. The J-ox kits include the J-ox as described above and () -meter cables for connecting to the valve. These cables have a connector on each end. The status indicator cable and the () solenoid cables have an M connector on one end and a DIN connector on the other end (M-DIN). Standard valves come with DIN type solenoid connections, but could be bought with M type connections as well. Therefore we also offer a kit that provides solenoid cables with an M connector on each end (M-M)..85 (6.9) 7 8 6 9 0 5. (5.9).5-6UN.90 (7.6).9 (00).0 (5) dia. 0.8 [.5] 6 0 Pin Pin # (V+) (V-) 5 6 7 8 9 0 7 5 8 9 0 Port Port Port Port Pin # Pin # Pin # Pin # 5 5 5 5 J-ox Wiring 0 PIN MINI Cable These cables have a 0-pin MINI connector for connecting the J-ox kits above to the user s control system. Kits include one cable with connector and cord grip. Cable conductors are 8-gauge wire. Kit Number Length meters (feet) 5H77.66 () 5H77 6. (0) 55H77 9. (0) 56H77 5. (50) PIN # + volts DC Common volts DC Solenoid Solenoid 5 Remote Reset Outlet Port Pressure Monitoring Wiring Kit PIN # 6-7 - 8-9 Remote Valve Fault Light 0 Remote System OK Light Wire Colors: Orange lue White w/lack Red w/lack reen w/lack Wire Colors: Orange w/lack Red reen/yellow lack White 7 8 6 9 0 5 Kit Number Length meters (feet) 5H77 (.) FEMLE 5 5 MLE PORT SPLITTER 5 FEMLE 5 Some customers prefer to monitor downstream pressure in addition to using the DM or DM Series valve. convenient way to do this is to install a pressure switch in the extra outlet port that is provided on the valve. The Outlet Port Pressure Monitoring kit can be used with one of the J-ox kits above to split one of the M ports on the J-ox so that a pressure switch can be wired in as well. These kits consist of one port splitter (a Tee with three M connectors) and one M-DIN cable ( meter). Ø0.6 Mx Female (0) 0. (7) 0.7 (0).6 Mx Male (0).6 Pressure switch available separately, see valve options. IMPORTNT NOTE: Please read carefully and thoroughly all of the CUTIONS, WRNINS on the inside back cover..7

ccessories & Options for Control Reliable Double Valves DM Series D ELECTRICL CONNECTORS Cord Electrical Connector Model Number Electrical Connector Cord Electrical Connector Type Length Form Diameter Without Lighted Connector meter (feet) Light Volts DC 0 Volts C DIN 650 Form Prewired Connector (8 gauge) (6/) 6-mm 7K77 70K77-W 70K77-Z DIN 650 Form Prewired Connector (8 gauge) (6/) 0-mm 7K77 8K77-W 8K77-Z DIN 650 Form Connector for threaded conduit (/ inch electrical conduit fittings) 7K77 7K77-W 7K77-Z DIN 650 Form Connector Only 97K87 96K87-W 96K87-Z STTUS INDICTOR The Status Indicator pressure switch actuates when the valve is in a ready-to-run condition and de-actuates when the valve is in a lockout condition or when the inlet air pressure has been removed. lthough, the valves can be purchased with this option already installed, the Status Indicator can be purchased separately. Model Number 6709 Downstream PressureMonitoring Pressure Switches Connection Type Model Number Port Threads DIN 650 Form 58686 /8 NPT M Micro-DC 50 /8 NPT DIN Connector Pinout Normally Open Normally Common Closed round M Connector Pinout Pin Normally Open Pin Common Pin Not Used Pin Normally Closed RESET VLVES for DOULE VLVES with REMOTE RESET Valves with the remote reset option require a small / reset valve and the installation of a /8 inch air line from the reset valve to the reset port of the double valve. ROSS offers / normally closed valves with either manual or electric control that are suitable for this purpose. Description Flush Pushbutton: reen Mushroom utton: reen Direct Solenoid Control for Line Mounting Direct Solenoid Control for ase Mounting Reset Valves Model Number FP M 600** W09** (ase: 569) * NPT threads. For SPP threads add a D prefix to the model number, e.g., DFP. ** Insert voltage code: W = volts DC; Z = 0-0 volts C, 50/60 Hz; e.g., 600W. Direct Solenoid Model for Line Mounting: 600** Flush Pushbutton: FP Mushroom utton: M Direct Solenoid Mode for ase Mounting Valve: W09** Sub-ase: 569 IMPORTNT NOTE: Please read carefully and thoroughly all of the CUTIONS, WRNINS on the inside back cover..8 05, ROSS CONTROLS. ll Rights Reserved.

ROSS CONTROLS Double Valves for Clutch/rake Control Serpar 5 Series

SERPR DOULE VLVES 5 SERIES DOULE VLVES WITH INTERNL MONITORIN & LOCKOUT KEY FETURES Internal monitoring requires no additional monitoring circuitry utomatic lock-out/inhibit upon detection of a malfunction Default to de-energized position upon fault detection Dedicated reset function No undesired automatic reset upon removal of electrical or pneumatic energy sources uilt-in non-clogging silencers on Sizes, 8, and 0 5 Series SERPR valves are internally monitored double valves and are available in Size, 8, and 0 ranging from /8 ½ port sizes. Internally monitored double valves contain a built-in monitoring device that checks for the proper operation of each valve element. If the internal monitor detects a valve fault on a particular cycle, the double valve will fail to a safe condition (all downstream air is exhausted) and the monitor will lock-out to inhibit further operation of the device. Normal operation can only be resumed by a momentary reset signal to the valve, either pneumatic or electric. The original application for these double valves was in the control of clutch/brake mechanisms on stamping presses, but they have found their way into many other critical applications such as alternative lockout systems for energy isolation, air cylinder press load-holding systems, as well as other Category - and - safety circuits. ROSS double valves are a vital part of any control-reliable fluid power control system. DESCRIPTION ge SERPR Double Valves with L- Monitor Size. -. SERPR Double Valves with L- Monitor Size 8,, 0.5 -.6 SERPR Double Valves with E-P Monitor Size 8,, 0.7 -.8 SERPR Double Valves with D-S Monitor Size 8,, 0.9 -.0

SERPR Double Valves with L- Monitor, Size 5 Series Model Number* vg. Response Constants Port asic Monitor C V Weight Size Size Reset F Right Inlet Left Inlet M lb (kg) - - - - /8 Manual 57D9** 57D95**.0 6.0 5 0.70 0.0 8. (.7) /8 Remote 57D9** 57D96**.0 6.0 5 0.70 0.0 8. (.7) / Manual 57D** 57D5**.0 8.0 5 0.65 0.5 8. (.7) / Remote 57D** 57D6**.0 8.0 5 0.65 0.5 8. (.7) / Manual 57D5** 57D55**.0 9.0 5 0.65 0.5 8. (.7) / Remote 57D5** 57D56**.0 9.0 5 0.65 0.5 8. (.7) * NPT port threads. For SPP threads, add a D prefix to the model number, e.g., D57D9W. ** Insert voltage code: W = volts DC; Z = 0-0 volts C, 50/60 Hz; e.g., 57D9W. For other voltages consult ROSS. Valve Response Time The constants above, designated M and F, can be used to determine the amount of time required to fill or exhaust a volume of any size using the formula on the right: Vlv. Resp. Time (msec)= M + F *V M = avg. time for parts movement F = msec. per cubic inch of volume V = volume in cubic inches YC Manual Reset COIL Signal COIL Signal Y Y YD ccessories & Options Pressure Switch (Electrical Lockout Indicator) Model Number* * /8 NPT port threads. 58686 (Lockout Indicator)L YE Valve Without Piping Flanges Port Size asic Size /8, /, / Monitor Model Number* Reset Right Inlet Left Inlet Manual 57D** 57D5** Remote 57D** 57D6** Piping Flange Kits Each kit includes two threaded (NPT) flanges and the required seals and mounting bolts. Port Size asic Size Kit Number /8 658K77 / 659K77 / 660K77 RESET VLVES for L- MONITOR On valve models with manual reset a button on the side of the monitor is pushed to perform the reset function. Models for remote reset, however, require a small reset valve and the installation of a /8 line from the reset valve to the reset port on the monitor. ROSS offers / normally closed valves with either manual or electric control that are suitable for this purpose, valves size 8,, 0 with L- monitor are suggested. Reset Valves Description Model Numbers Flush Pushbutton: reen FP Mushroom utton: reen M Direct Solenoid Control for Line Mounting 600** Direct Solenoid Control for ase Mounting W09** (ase: 569) * NPT port threads. For SPP threads, add a D prefix to the model number, e.g., D57DW. ** Insert voltage code: W = volts DC; Z = 0-0 volts C, 50/60 Hz; e.g., 57DW. For other voltages consult ROSS. Valve Without Silencer Exhaust port has threaded flange only, consult ROSS. STNDRD SPECIFICTIONS (for valves on this page): Construction: Dual poppet. Mounting Type: Inline. Pilot Solenoids: Two, rated for continuous duty. Standard Voltages: volts DC; 0-0 volts C, 50/60 Hz. Power Consumption (each solenoid): 0 V inrush, 6 V holding on 50 or 60 Hz; watts on DC. Electrical Connections: Cord-grip connectors at solenoids. mbient Temperature: 0 to 0 F ( to 50 C). Media Temperature: 0 to 75 F ( to 80 C). Flow Media: Filtered air. Inlet Pressure: 0 to 00 psig ( to 7 bar). L- Reset Pressure: Remote pneumatic reset models require a pressure of at least 0 psig ( bar). Manual reset models use internal valve pressure. Inlet Port: Models are available with the inlet port on either the right or the left side of the valve body. IMPORTNT NOTE: Please read carefully and thoroughly all of the CUTIONS, WRNINS on the inside back cover..

SERPR Double Valves with L- Monitor 5 Series Valve Technical Data & Operation Valve Dimensions inches (mm) 8.00 (0) /8 Remote pneumatic reset port or manual reset Inlet or outlet port 5.0 (9).50 (6) 0. (7.8) places LEFT SIDE RIHT SIDE. (6).80 (70) 6.0 (55).05 (5).0 (0) 6.70 (70) 7.0 (8) (78).08 Options ELECTRICL CONNECTORS Electrical Connector Form Electrical Connector Type Cord Length meter (feet) Cord Diameter Electrical Connector Model Number Without Light Lighted Connector Volts DC 0 Volts C DIN 650 Form Prewired Connector (8 gauge) (6/) 6-mm 7K77 70K77-W 70K77-Z DIN 650 Form Prewired Connector (8 gauge) (6/) 0-mm 7K77 8K77-W 8K77-Z DIN 650 Form Connector for threaded conduit (/ inch electrical conduit fittings) 7K77 7K77-W 7K77-Z DIN 650 Form Connector Only 97K87 96K87-W 96K87-Z VLVE OPERTION Conditions at Start: Inlet is closed to outlet by both valve elements and. Outlet is open to exhaust. Pilot air is ported from inlet and through the center section of spool S to the normally closed pilots and. Monitoring pressure signals at both ends of spool S are exhausted. S Detecting a Malfunction: malfunction in the system or the valve itself could cause one valve element to be open and the other closed. ir then flows past the inlet poppet on valve element, into crossflow passage D, but is substantially blocked by the spool portion of element. The large size of the open exhaust passage past element keeps the pressure at the outlet port below two percent of inlet pressure. Full monitoring air pressure from side goes to the right end of spool S, and a reduced pressure goes to the left end. This pressure imbalance causes the spool to shift to the left. This shuts off and exhausts pilot air to both solenoid pilots, and allows valve element to return to the closed position. S CD Normal Operation: Simultaneously energizing both solenoids actuates both pilots and causes valve elements and to shift. Inlet is then connected to outlet via crossflow passages C and D. Exhaust is closed. Monitoring pressure signals go to each end of spool S and become equal to inlet pressure. CD S L- Monitor Locked-out: When the L- spool shifts it is held by a lockout pin (not shown). Pilot air is then exhausted to atmosphere via port Y, and pilot supply air is diverted to atmosphere via port Y. The lockout mechanism must be reset before the valve can return to normal operation. During and following reset, the pilot solenoids must be kept de-energized to prevent inadvertent and possibly dangerous cycling of the press. The reset function is either manual or remote-pneumatic depending on valve model. Y S Y oth solenoids must be energized simultaneously to shift the valve; maintained signal required to keep valve shifted. WRNIN: If monitor must be reset, electrical signals to both solenoids must be removed to prevent the machine controlled by the valve from immediately recycling and producing a potentially hazardous condition. IMPORTNT NOTE: Please read carefully and thoroughly all of the CUTIONS, WRNINS on the inside back cover.. 05, ROSS CONTROLS. ll Rights Reserved.

SERPR Double Valves with L- Monitor, Size 8,, 0 5 Series Port Size asic Size Model Number* C V vg. Response Constants F With Overrides Without Overrides M - - - - Weight lb (kg) / 8 57** 576**.5 8.5 5 0.70 0.0 5. (6.9) / 8 575** 5756**.0 5 0.65 0. 9.0 (8.6) / 5755** 5757** 8.0 5 5 0.65 0. 9.0 (8.6) 8 5765** 5767**.0 0 0. 0. 5. (6.9) 5766** 5768** 8.5 9 0 0.8 0. 9.0 (8.6) / 5776** 5778** 9.0 0 0.8 0. 9.0 (8.6) / 0 5775** 5777** 0 5 0.9 0.07 7.5 (6.9) / 0 5786** 5788** 5 0.8 0.07 7.5 (6.9) 0 inch port size available on size 0 valves. Order part number 999H77 flange kit separately. * NPT port threads. For SPP threads, add a D prefix to the model number, e.g., D57W. ** Insert voltage code: W = volts DC; Z = 0-0 volts C, 50/60 Hz; e.g., 57W. For other voltages consult ROSS. Solenoid Solenoid Valve Response Time The constants above, designated M and F, can be used to determine the amount of time required to fill or exhaust a volume of any size using the formula on the right: Vlv. Resp. Time (msec)= M + F *V M = avg. time for parts movement F = msec. per cubic inch of volume V = volume in cubic inches Lockout Indicator Options Pressure Switch (Electrical Lockout Indicator) Model Number* 58686 * /8 NPT port threads. Y Y Z (Pneumatic Reset Port) Valve Without Piping Flanges Piping Flange Kits Each kit includes two threaded (NPT) flanges and the required seals and mounting bolts. Valve Without Silencer Port Size asic Model Number* Size With Overrides Without Overrides /, /, 8 570** 57** /,, / 5750** 575** /, / 0 5770** 577** Exhaust port has threaded flange only, consult ROSS. Port Size asic Pipe Flange Size Kit Number / 8 66K77 / 8 66K77 8 66K77 / 66K77 665K77 / 666K77 / 0 667K77 / 0 668K77 RESET VLVES for L- MONITOR On valve models with manual reset a button on the side of the monitor is pushed to perform the reset function. Models for remote reset, however, require a small reset valve and the installation of a /8 line from the reset valve to the reset port on the monitor. ROSS offers / normally closed valves with either manual or electric control that are suitable for this purpose, valves size 8,, 0 with L- monitor are suggested. Reset Valves Description Flush Pushbutton: reen Mushroom utton: reen Direct Solenoid Control for Line Mounting Direct Solenoid Control for ase Mounting Model Number* FP M 600** W09** (ase: 569) * NPT port threads. For SPP threads, add a D prefix to the model number, e.g., D570W. ** Insert voltage code: W = volts DC; Z = 0-0 volts C, 50/60 Hz; e.g., 570W. For other voltages consult ROSS. STNDRD SPECIFICTIONS (for valves on this page): Construction: Dual poppet. Mounting Type: Inline. Pilot Solenoids: Two, rated for continuous duty. Standard Voltages: volts DC; 0-0 volts C, 50/60 Hz. Power Consumption (each solenoid): 87 V inrush, 0 V holding on 50 or 60 Hz; watts on DC. Electrical Connections: Uses terminal strip connectors. mbient Temperature: 0 to 0 F ( to 50 C). Media Temperature: 0 to 75 F ( to 80 C). Flow Media: Filtered air. Inlet Pressure: 0 to 5 psig ( to 8.5 bar). L- Reset Pressure: 60 psig ( bar) minimum. IMPORTNT NOTE: Please read carefully and thoroughly all of the CUTIONS, WRNINS on the inside back cover..5

SERPR Double Valves with L- Monitor Valve Dimensions inches (mm) asic Size 8 5 Series Valve Technical Data & Operation VLVE OPERTION.0 () Port (outlet).5 (6) 5.06 (8).6 (06) 8.5 (6) asic Size.80 (5) Port (outlet).75 (70) 5.50 (0).8 () 8.96 (8) asic Size 0 0.8 (7) ( places).7 (6).7 (6).0 (5).68 (9) 0. (9) ( places).00 (76).08 (0) /8 Lockout indicator port /8 Pneumatic reset port Port (inlet) / NPSC electrical opening /8 Lockout indicator port /8 Pneumatic reset port Port (inlet) / NPSC electrical opening 7.0 (8) 8.60 (6). (0).5 ().0 (5).69 ().09 (5).60 (66).5 (6) 5. ().8 (6).0 (6).80 (6).09 (5).00 (76).5 (6) Conditions at Start: Inlet is closed to outlet by both valve elements and. Outlet is open to exhaust. Pilot air is ported from inlet and through the center section of spool S to the normally closed pilots and. Monitoring pressure signals at both ends of spool S are exhausted. Normal Operation: Simultaneously energizing both solenoids actuates both pilots and causes valve elements and to shift. Inlet is then connected to outlet via crossflow passages C and D. Exhaust is closed. Monitoring pressure signals go to each end of spool S and become equal to inlet pressure. Detecting a Malfunction: malfunction in the system or the valve itself could cause one valve element to be open and the other closed. ir then flows past the inlet poppet on valve element, into crossflow passage D, but is substantially blocked by the spool portion of element. The large size of the open exhaust passage past element keeps the pressure at the outlet port below two percent of inlet pressure. Full monitoring air pressure from side goes to the right end of spool S, and a reduced pressure goes to the left end. This pressure imbalance causes the spool to shift to the left. This shuts off and exhausts pilot air to both solenoid pilots, and allows valve element to return to the closed position. S S CD S CD 7.80 (5) Port (outlet).8 (09) 8.56 (7) 6.8 (57).6 () 0.5 () ( places).7 (6).70 (9).0 (0) /8 Lockout indicator port /8 Pneumatic reset port Port (inlet) / NPSC electrical opening.0 (8) 9.6 (8).5 (5).50 (6).7 (58).65 (67) 5.90 (50).0 (77) L- Monitor Locked-out: When the L- spool shifts it is held by a lockout pin (not shown). Pilot air is then exhausted to atmosphere via port Y, and pilot supply air is diverted to atmosphere via port Y. The lockout mechanism must be reset before the valve can return to normal operation. During and following reset, the pilot solenoids must be kept de-energized to prevent inadvertent and possibly dangerous cycling of the press. The reset function is either manual or remote-pneumatic depending on valve model. Y S Y oth solenoids must be energized simultaneously to shift the valve; maintained signal required to keep valve shifted. WRNIN: If monitor must be reset, electrical signals to both solenoids must be removed to prevent the machine controlled by the valve from immediately recycling and producing a potentially hazardous condition. IMPORTNT NOTE: Please read carefully and thoroughly all of the CUTIONS, WRNINS on the inside back cover..6 05, ROSS CONTROLS. ll Rights Reserved.

SERPR Double Valves with E-P Monitor 5 Series Port Size asic Size Single Signal Input With Overrides Model Number* Without Overrides Dual Signal Input With Overrides Without Overrides C V - - M vg. Response Constants F - - Weight lb (kg) / 8 57** 576** 57** 756**.5 8.5 5 0.70 0.0.8 (5.) / 8 575** 5756** 575** 5756**.0 5 0.65 0..8 (5.) / 5755** 5757** 5755** 5757** 8.0 5 5 0.65 0. 5.5 (7.0) 8 5765** 5767** 5765** 5767**.0 0 0. 0..8 (5.) 5766** 5768** 5766** 5768** 8.5 9 0 0.8 0. 5.5 (7.0) / 5776** 5778** 5776** 5778** 9.0 0 0.8 0. 5.5 (7.0) / 0 5775** 5777** 5775** 5777** 0 5 0.9 0.07 5.0 (5.8) / 0 5786** 5788** 5786** 5788** 5 0.8 0.07 5.0 (5.8) 0 inch port size available on size 0 valves. Order part number 999H77 flange kit separately. * NPT port threads. For SPP threads, add a D prefix to the model number, e.g., D57W. ** Insert voltage code: W = volts DC; Z = 0-0 volts C, 50/60 Hz; e.g., 57W. For other voltages consult ROSS. SOL INPUT COM. RESET SOL RESET SOL SOL INPUT COM. SOL INPUT RESET SOL RESET SOL Valve Response Time The constants above, designated M and F, can be used to determine the amount of time required to fill or exhaust a volume of any size using the formula below: Vlv. Resp. Time (msec)= M + F *V M = avg. time for parts movement F = msec. per cubic inch of volume V = volume in cubic inches 5 6 7 8 9 a c Single Input Wiring Diagram b 5 6 7 8 9 During lock-out: Terminals and 7 are connected which allows a panel light, bell, or other electrical device to be wired through terminals 7 and to serve as a lockout indicator. a c Dual Input Wiring Diagram b Options Valve Without Piping Flanges Model Number* asic Port Size Single Signal Input Dual Signal Input Size With Overrides Without Overrides With Overrides Without Overrides /, /, 8 570** 57** 570** 57** /,, / 5750** 575** 5750** 575** /, / 0 5770** 577** 5770** 577** * NPT port threads. For SPP threads, add a D prefix to the model number, e.g., D570W. ** Insert voltage code: W = volts DC; Z = 0-0 volts C, 50/60 Hz; e.g., 570W. For other voltages consult ROSS. Piping Flange Kits Each kit includes two threaded (NPT) flanges and the required seals and mounting bolts. Valve Without Silencer Exhaust port has threaded flange only, consult ROSS. STNDRD SPECIFICTIONS (for valves on this page): Port Size asic Size Kit Number / 8 66K77 / 8 66K77 8 66K77 / 66K77 665K77 / 666K77 / 0 667K77 / 0 668K77 Construction: Dual poppet. Mounting Type: Inline. Pilot Solenoids: Two, rated for continuous duty. Standard Voltages: volts DC; 0-0 volts C, 50/60 Hz. Power Consumption (each solenoid): 87 V inrush, 0 V holding on 50 or 60 Hz; watts on DC. E-P Reset Solenoid: Rated for intermittent duty. Voltages: -8 or 00-0 volts C or DC. mbient Temperature: 0 to 0 F ( to 50 C). Media Temperature: 0 to 75 F ( to 80 C). Flow Media: Filtered air. Pressure Range: 0 to 5 psig ( to 8.5 bar). IMPORTNT NOTE: Please read carefully and thoroughly all of the CUTIONS, WRNINS on the inside back cover..7

SERPR Double Valves with E-P Monitor Valve Dimensions inches (mm) asic Size 8 5 Series Valve Technical Data & Operation VLVE OPERTION.0 (88) Port 0.8 (7) (outlet) ( places) Port (inlet).0 (5).70 (8).5 (). (6) Conditions at Start: Inlet is closed to outlet by both valve elements and. Outlet is open to exhaust. Contacts of switch SW are closed. Monitoring pressure signals at both ends of spool S are exhausted. S SW.5 (6) 5.06 (8).6 (06).6 (67) 8.5 (6) asic Size / NPSC electrical opening 7.0 (8).70 ().80 (6).60 (66) Normal Operation: Simultaneously energizing both solenoids actuates both pilots and causes valve elements and to shift. Inlet is then connected to outlet via crossflow passages C and D. Exhaust is closed. Monitoring pressure signals go to each end of spool S and become equal to inlet pressure. CD S SW.80 () Port (outlet) 0. (9) ( places).00 (76) Port (inlet).8 (6) Completion of Normal Cycle: Simultaneously de-energizing both solenoids returns the valve to the Conditions at Start described above..75 (70) 5.50 (0).8 () 8.96 (8) asic Size 0 7.0 (0) Port (outlet).6 (67) 5.00 (7) 0.5 () ( places).8 (09) 8.56 (7) 6.8 (57).6 (67).6 () 5.90 (50) 5.0 (0) / NPSC electrical opening 8.0 (06) Port (inlet) / NPSC electrical opening.0 (8).8 (7).80 (6).09 (5).00 (76).5 (5).9 (7).09 (5).7 (58).70 (9) Detecting a Malfunction: malfunction in the system or the valve itself could cause one valve element to be open and the other closed. ir then flows past the inlet poppet on valve element, into crossflow passage D, but is substantially blocked by the spool portion of element. The large size of the open exhaust passage past element keeps the pressure at the outlet port below two percent of inlet pressure. Full monitoring air pressure from side goes to the right end of spool S, and a reduced pressure goes to the left end. This pressure imbalance causes the spool to shift to the left. This trips switch SW, breaks the electrical circuit to the pilot solenoids, and allows valve element to return to the closed position. E-P Monitor Locked-out: With both valve elements closed, monitoring air pressure is exhausted from both ends of spool S so that it returns to its normal position. The electrical circuit to the pilot solenoids remains broken by switch SW. To restore the electrical circuit and return the valve to normal operation, the reset solenoid (not shown) must be briefly energized to reset switch SW. During and following reset, the pilot solenoids must be kept de-energized to prevent inadvertent and possibly dangerous cycling of the press. Prolonged energizing of the reset solenoid can cause burnout and nullify the reset function. S CD S SW SW IMPORTNT NOTE: Please read carefully and thoroughly all of the CUTIONS, WRNINS on the inside back cover..8 05, ROSS CONTROLS. ll Rights Reserved.

SERPR Double Valves with D-S Monitor 5 Series Port Size asic Size With Overrides Model Number* Without Overrides C V vg. Response Constants F M - - - - Weight lb (kg) / 8 57** 576**.5 8.5 5 0.70 0.0 6.8 (7.6) / 8 575** 5756**.0 5 0.65 0. 6.8 (7.6) / 5755** 5757** 8.0 5 5 0.65 0. 0.5 (9.) 8 5765** 5767**.0 0 0. 0. 6.8 (7.6) 5766** 5768** 8.5 9 0 0.8 0. 0.5 (9.) / 5776** 5778** 9.0 0 0.8 0. 0.5 (9.) / 0 5775** 5777** 0 5 0.9 0.07 9. (7.7) / 0 5786** 5788** 5 0.8 0.07 9. (7.7) 0 inch port size available on size 0 valves. Order part number 999H77 flange kit separately. * NPT port threads. For SPP threads, add a D prefix to the model number, e.g., D57W. ** Insert voltage code: W = volts DC; Z = 0-0 volts C, 50/60 Hz; e.g., 57W. For other voltages consult ROSS. Valve Response Time The constants above, designated M and F, can be used to determine the amount of time required to fill or exhaust a volume of any size using the formula below: Vlv. Resp. Time (msec)= M + F *V M = avg. time for parts movement F = msec. per cubic inch of volume V = volume in cubic inches b C D E F H J K POWER SOL. a POWER SOL. b MONITOR RESET FULT POWER SWITCH INDICTOR a D-S MONITOR Wiring Diagram D-S MONITOR Options Valve Without Piping Flanges Port Size asic Size Model Number* With Overrides Without Overrides /, /, 8 570** 57** /,, / 5750** 575** /, / 0 5770** 577** * NPT port threads. For SPP threads, add a D prefix to the model number, e.g., D570W. ** Insert voltage code: W = volts DC; Z = 0-0 volts C, 50/60 Hz; e.g., 570W. For other voltages consult ROSS. Piping Flange Kits Each kit includes two threaded (NPT) flanges and the required seals and mounting bolts. Valve Without Silencer Exhaust port has threaded flange only, consult ROSS. STNDRD SPECIFICTIONS (for valves on this page): Port Size asic Size Kit Number / 8 66K77 / 8 66K77 8 66K77 / 66K77 665K77 / 666K77 / 0 667K77 / 0 668K77 Construction: Dual poppet. Mounting Type: Inline. Pilot Solenoids: Two, rated for continuous duty. Standard Voltages: volts DC; 0-0 volts C, 50/60 Hz. Power Consumption (each solenoid): 87 V inrush, 0 V holding on 50 or 60 Hz; watts on DC. D-S Monitor: Rated for same voltage as pilot solenoids. Power supply to monitor must be independent and continuous. mbient Temperature: 0 to 0 F ( to 50 C). Media Temperature: 0 to 75 F ( to 80 C). Flow Media: Filtered air. Pressure Range: 0 to 5 psig ( to 8.5 bar). IMPORTNT NOTE: Please read carefully and thoroughly all of the CUTIONS, WRNINS on the inside back cover..9

SERPR Double Valves with D-S Monitor Valve Dimensions inches (mm) asic Size 8 5 Series Valve Technical Data & Operation VLVE OPERTION Port (outlet) 0.8 (7) ( places).5 (6) 6.50 (8) 9.90 (5) Port (inlet) / NPSC electrical opening.5 () 8.8 () Conditions at Start: Inlet is closed to outlet by both valve elements and. Outlet is open to exhaust. Contacts of switch SW are closed. Monitoring pressure signals at both ends of spool S are exhausted. SWb Sb Sa Ib Ia SWa COMPRTOR and CONTROL CIRCUITS.5 (6) Size Port (outlet) H 5.06 (8).6 (06) 8.5 (6). (87) 0. (9) ( places).00 (76) 7.80 (5) 7.0 (8) Port (inlet).80 (6).60 (66).70 (69).8 (6) Normal Operation: Simultaneously energizing both solenoids actuates both pilots and causes valve elements and to shift. Inlet is then connected to outlet via crossflow passages C and D. Exhaust is closed. Monitoring pressure signals go to pressure indicators Ia and Ib, causing the indicator pins to be extended and to actuate proximity switches SWa and SWb. In normal operation, each pair - solenoids, valve elements, indicators, and proximity switches - responds in unison so that the comparator circuits read the operation as normal. SWb Sb Sa CD Ib Ia SWa COMPRTOR and CONTROL CIRCUITS Completion of Normal Cycle: Simultaneously de-energizing both solenoids returns the valve to the Conditions at Start described above..75 (70) 5.50 (0)..8 () (87 8.96 (8) Size 0 Port (outlet).8 (09) 8.56 (7) 6.8 (57). (87).6 () 0.0 (6) 0.5 () ( places) 5.90 (50) 9.70 (5).80 (55) / NPSC electrical opening 8.0 (06) Port (inlet) / NPSC electrical opening.0 (8) 9.8 (.).80 (6).00 (76).70 (69).5 (5) 8.5 (7).7 (58).70 (9).06 (78) Detecting a Malfunction: malfunction in the system or the valve itself could cause one valve element to be open and the other closed. ir then flows past the inlet poppet on valve element, into crossflow passage D, but is substantially blocked by the spool portion of element. The large size of the open exhaust passage past element keeps the pressure at the outlet port below two percent of inlet pressure. Full monitoring air pressure from side goes to pressure indicator Ia so that its pin is extended and actuates proximity switch SWa. When the time interval between the signal to a solenoid and the signal from its corresponding proximity switch exceeds approximately 75 milliseconds, the D-S monitor breaks contacts Sa and Sb as soon as solenoid power is removed. This allows valve element to return to the closed position. D-S Monitor Locked-out: With the valve locked out by contacts Sa and Sb, solenoids and cannot be energized. The monitor must be reset before another valve cycle can begin. Reset can be achieved by a separately connected ancillary switch, but not if the pilot solenoids are energized. The monitor can be reset by removing and reapplying power to the monitor even when the pilot solenoids are energized. For this reason it is necessary to have the pilot solenoids de-energized during and following reset to prevent inadvertent and possibly dangerous cycling of the press. SWb Sb Sa SWb Sb Sa CD Ib Ia SWa COMPRTOR and CONTROL CIRCUITS Ib Ia SWa COMPRTOR and CONTROL CIRCUITS.0 05, ROSS CONTROLS. ll Rights Reserved.

ROSS CONTROLS Double Valves for Clutch/rake Control SERPR Crossflow 5 Series

SERPR CROSSFLOW DOULE VLVES 5 SERIES WITH PRESSURE SWITCHES FOR EXTERNL MONITORIN KEY FETURES Designed to enable users to comply with current safety regulations Can be integrated with external monitoring systems to provide for lockout and inhibiting further machine operation until the controls system is reset Default to de-energized position upon fault condition uilt-in non-clogging silencers on Sizes, 8, and 0 Size and SERPR Crossflow valves with pressure switches (for external monitoring) are available from ¼ to ¾ port sizes. Externally monitored double valves provide feedback signals (via the pressure switches), which allows the main press controls, or separate monitoring device, The original application for these double valves was in the control of clutch/brake mechanisms on stamping presses, but they have found their way into many other critical applications such as alternative lockout systems for energy isolation, air cylinder press load-holding systems, as well as other Category - and - safety circuits. ROSS double valves are a vital part of any control-reliable fluid power control system. DESCRIPTION ge SERPR Crossflow Double Valves with or without Pressure Switches Size. -. SERPR Crossflow Double Valves with or without Pressure Switches Size.5 -.6 SERPR Crossflow Double Valves with Pressure Switches Size.7 SERPR Crossflow Double Valves with Pressure Switches Size 8,, 0.8 -.9

SERPR Crossflow Double Valves with or without Pressure Switches, Size 5 Series Port Sizes Pressure vg. Response Constants Pressure C asic Size Switch Model Number* V Switches F Provision M, - - - - Weight lb (kg) / / None Yes 576** 0.9. 8.6.. (95) / /8 None No 5760** 0.9.... (95) / / Two## Yes 576** 0.9. 8.6..5 (.) /8 /8 Two## Yes 576**..7 5..8.9 (.) /8 /8 None Yes 5765**..7 5..8.5 (.) * NPT port threads. For SPP threads, add a D prefix to the model number, e.g., D576W. ** Insert voltage code: W = volts DC; Z = 0-0 volts C, 50/60 Hz; e.g., 576W. For other voltages consult ROSS. Valve and base can be ordered separately, consult ROSS. ## Only valves with pressure switches should be used to control clutch/brake mechanisms on press machinery. The pressure switches must be used in conjunction with a monitoring device to assist with OSH compliance (Ref. 90.7). Valve Response Time The constants above, designated M and F, can be used to determine the amount of time required to fill or exhaust a volume of any size using the formula on the right: Vlv. Resp. Time (msec)= M + F *V M = avg. time for parts movement F = msec. per cubic inch of volume V = volume in cubic inches * Non-monitored COIL Signal COIL Signal Solenoid Solenoid ## Pressure Switches & Monitoring: Valves without pressure switches must not be used to control clutch/brake mechanisms on press machinery. Valves with pressure switches must be used in conjunction with an external monitoring device to assist with OSH compliance (Ref. 90.7). The valves on this page do not have a built-in monitor, and must only be used in conjunction with an external monitoring system. Such monitoring system must be capable of inhibiting the operation of the valve in the event of a failure within the valve. SW SW ccessorries & Options To customer s external monitor Electrical Connectors for use with Dropcords DIN 650, Form Electrical Connector Model Number Cord Length Cord Lighted Connector meters (feet) Diameter Without Light Volts DC 0 Volts C Prewired Connector (8 gauge) (6/) 0-mm 66K87 67K87-W 67K87-Z Connector Only 66K87 67K87-W 67K87-Z Silencers Port Thread Model Number vg. Dimensions inches (mm) Weight Size Type NPT Threads SPP Threads C V lb (kg) / Male 550000 D550000. 0.9 (). (55) 0. (0.) /8 Male 55000 D55000.7 0.9 (). (55) 0. (0.) Pressure Range: 0 to 50 psig (0 to 0. bar) maximum. Flow Media: Filtered air. STNDRD SPECIFICTIONS (for valves on this page): Construction: Dual poppet. Mounting Type: Inline. Pilot Solenoids: Two, rated for continuous duty. Standard Voltages: volts DC; 0-0 volts C, 50/60 Hz. Power Consumption (each solenoid): V maximum inrush, 9.8 V maximum holding on 50 or 60 Hz; 7.5 watts nominal on DC. Electrical Connections: Uses two cord-grip connectors at solenoids. DIN 650 Form connector P/N 66K77. mbient Temperature: 0 to 0 F ( to 50 C). Media Temperature: 0 to 75 F ( to 80 C). Flow Media: Filtered air. Inlet Pressure: 0 to 00 psig (.8 to 7 bar). Functional Safety Data: Category PL e; 0d: 0,000,000; PFHd: 7.7x0-9 ; MTTFd: 0.9 (n op: 6600). Certifications: CE Marked for applicable directives,, CS/UL. Vibration/Impact Resistance: Tested to S EN 60068--7. IMPORTNT NOTE: Please read carefully and thoroughly all of the CUTIONS, WRNINS on the inside back cover..

SERPR Crossflow Double Valves with or without Pressure Switches 5 Series Valve Technical Data & Operation Valve without Pressure Switches.76 (5) 0.6 () Valve with Pressure Switches.7 (69).8 (60.) 0.6 ().76 (5).56 (0) Valve Dimensions inches (mm) 5.0 (7) 7.5 (90.5) ase 0.78 (0) 0.6 ().8 (60.).7 (69) 0.87 () 0.6 ().56 (0) 0.78 (0) 0.87 () C F* N E J K M D H L Valve Model Number ase Model Number SE Dimensions inches (mm) C D E F H J K L M N 576 0C9 0. () 0.7 (7).9 (.8) 0. ().7 (69). (6) 0. (5).8 (60.5).6 () 0. ().8 (6). (0).5 (8) 5760 0C9 0.5 () 0.6 (5).6 (.5) 0. ().7 (69). (6) 0. (5).8 (60.5).6 () 0. ().8 (6). (0).5 (8) 576 888C9 0. () 0.7 (7).9 (.8) 0. ().7 (69). (6) 0. (5).8 (60.5).6 () 0. ().8 (6). (0).5 (8) 576 7C9 0.5 () 0.6 (5).7 (7.) 0.5 ().7 (69).5 (6) 0. (5).8 (60.5).6 () 0.8 (9).8 (6). (7).5 (8) 5765 7C9 0.5 () 0.6 (5).7 (7.) 0.5 ().7 (69).5 (6) 0. (5).8 (60.5).6 () 0.8 (9).8 (6). (7).5 (8) For replacement valve (less base), order model 5760. Valve Operation: oth solenoids must be energized simultaneously to shift the valve; maintained signal required to keep valve shifted. CUTION: If the monitor must be reset, electrical signals to both solenoids must be removed to prevent the machine controlled by the valve from immediately recycling and producing a potentially hazardous condition. VLVE OPERTION Conditions at Start: Inlet is closed to outlet by both valve elements and. Outlet is open to exhaust. Pressure signals at both switches SW and SW are exhausted. Contacts and of switches SW and SW are connected. Normal Operation: Simultaneously energizing both solenoids actuates both pilots and causes valve elements and to shift. Inlet is then connected to outlet via crossflow passages C and D. Exhaust is closed. Sensing pressure signals go to each pressure switch and become equal to inlet pressure. oth switches trip and now contacts and of switches SW and SW are connected instead of contacts and. SW SW C D SW SW Completion of Normal Cycle: Simultaneously de-energizing both solenoids returns the valve to the Conditions at Start described at left. Detecting a Malfunction: malfunction in the system or the valve itself could cause one valve element to be open and the other closed. ir then flows past the inlet poppet on valve element, into crossflow passage D, but is substantially blocked by the spool portion of element. The large size of the open exhaust passage past element keeps the pressure at the outlet port below % of inlet pressure. Full sensing air pressure from side goes to switch SW, and a reduced pressure goes to switch SW. This full pressure signal causes switch SW to trip. Switch SW, with a reduced pressure signal, does not trip. n external monitoring system can detect the malfunction by monitoring the condition of the switches SW and SW. The external monitoring system may then react accordingly by shutting down the power to the valve solenoids and any other components deemed necessary to stop the machine. SW C D SW IMPORTNT NOTE: Please read carefully and thoroughly all of the CUTIONS, WRNINS on the inside back cover.. 05, ROSS CONTROLS. ll Rights Reserved.

SERPR Crossflow Double Valves with or without Pressure Switches, Size 5 Series Port Pressure vg. Response Constants asic Inlet Pressure C Sizes Switch Model Number* V Weight F Size Orientation Switches M lb (kg), Provision - - - - / / Left Hand None No 57C60**.7 6.6 0..0. (.95) / / Left Hand None Yes 57C6**.7 6.6 0..0. (.95) / / Left Hand None No 57C60**.7 9.0 5. 0.9. (.95) / / Left Hand Two ## Yes 57C6**.7 6.6 0..0.8 (.8) / / Left Hand None No 57C6**. 9.0 5. 0.9.7 (.) / / Left Hand Two ## Yes 57C6**. 9.0 5. 0.9 5. (.6) / / Left Hand None Yes 57C65**. 9.0 5. 0.9.7 (.) / / Left Hand Two ## Yes 57C65**.7 9.0 5. 0.9. (.95) / Right Hand Two ## Yes 57C706**.7 9.0 0..0. (.95) / Right Hand Two ## Yes 57C75**. 9.0 5. 0.9 5. (.6) / Left Hand None No 5775**.7 9.0 0..0. (.95) / Left Hand Two ## Yes 5776**.7 9.0 0..0. (.95) / Left Hand None No 5777**. 9.0 5. 0.9 5. (.6) / Left Hand Two ## Yes 5778**.7 9.0 5. 0.9 5. (.6) / Right Hand None No 5788**. 9.0 5. 0.9 5. (.6) / Right Hand None No 5789**. 9.0 0..0. (.95) * NPT port threads. For SPP threads, add a D prefix to the model number, e.g., D57C60W. ** Insert voltage code: W = volts DC; Z = 0-0 volts C, 50/60 Hz; e.g., 57C60W. For other voltages consult ROSS. Valve and base can be ordered separately, consult ROSS. ## Only valves with pressure switches should be used to control clutch/brake mechanisms on press machinery. The pressure switches must be used in conjunction with a monitoring device to assist with OSH compliance (Ref. 90.7). * Non-monitored COIL Signal COIL Signal Valve Response Time The constants above, designated M and F, can be used to determine the amount of time required to fill or exhaust a volume of any size using the formula on the right: Vlv. Resp. Time (msec)= M + F *V M = avg. time for parts movement F = msec. per cubic inch of volume V = volume in cubic inches Solenoid Solenoid ## Pressure Switches & Monitoring: Valves without pressure switches must not be used to control clutch/brake mechanisms on press machinery. Valves with pressure switches must be used in conjunction with an external monitoring device to assist with OSH compliance (Ref. 90.7). The valves on this page do not have a built-in monitor, and must only be used in conjunction with an external monitoring system. Such monitoring system must be capable of inhibiting the operation of the valve in the event of a failure within the valve. SW SW To customer s external monitor Valve Operation: oth solenoids must be energized simultaneously to shift the valve; maintained signal required to keep valve shifted. CUTION: If the monitor must be reset, electrical signals to both solenoids must be removed to prevent the machine controlled by the valve from immediately recycling and producing a potentially hazardous condition. STNDRD SPECIFICTIONS (for valves on this page): Construction: Dual poppet. Mounting Type: Inline. Pilot Solenoids: Two, rated for continuous duty. Standard Voltages: volts DC; 0-0 volts C, 50/60 Hz. Power Consumption (each solenoid): 8.5 V maximum inrush, 8.5 V maximum holding on 50 or 60 Hz; 6 watts nominal on DC. Electrical Connections: Uses two cord-grip connectors at solenoids. Din 650 Form connector P/N 97K87. mbient Temperature: 0 to 0 F ( to 50 C). Media Temperature: 0 to 75 F ( to 80 C). Flow Media: Filtered air. Inlet Pressure: 0 to 00 psig (.8 to 7 bar). Functional Safety Data: Category PL e; 0d: 0,000,000; PFHd: 7.7x0-9 ; MTTFd: 0.9 (n op: 6600). Certifications: CE Marked for applicable directives,, CS/UL. Vibration/Impact Resistance: Tested to S EN 60068--7. IMPORTNT NOTE: Please read carefully and thoroughly all of the CUTIONS, WRNINS on the inside back cover..5

SERPR Crossflow Double Valves with or without Pressure Switches 5 Series Valve Technical Data & Operation.78 (5.) Valve without Pressure Switches.8 (7) 6. (60) 0.5 (6.).78 (5.). (86).85 (7.) 0.5 (6.) Valve with Pressure Switches.8 (6).8 (7) 8.8 (.5) C Valve Dimensions inches (mm) ase E K M J F* 0.5 (6.).85 (7.). (86) 0.5 (6.).8 (6) D H L Valve Model Number ase Model Number SE Dimensions inches (mm) C D E F H J K L M 5760 6C9 0.8 (9) 0.7 (7).5 (5.6) 0.6 (5). (86).0 (0) 0. (7).85 (7.). (56) 0.8 (9). (6).6 (9) 576 C9 0.8 (9) 0.7 (7).5 (5.6) 0.6 (5). (86).0 (0) 0. (7).85 (7.). (56) 0.8 (9). (6).6 (9) 5760 08C9. (7).0 (). (58.9) 0.6 (5). (86). (0) 0. (7).85 (7.).6 (6) 0.8 (9).7 ().9 (8) 576 89C9 0.8 (9) 0.7 (7).5 (5.6) 0.6 (5). (86).0 (0) 0. (7).85 (7.). (56) 0.8 (9). (6).6 (9) 576 C9. (7) 0.8 (9).6 (67.). ().7 (9). (0) 0. (7).85 (7.).6 (6) 0.7 (7).0 (50).8 (6) 576 6C9. (7) 0.8 (9).86 (7.7) 0.7 (7).7 (9). (0) 0. (7).85 (7.).6 (6) 0.7 (7).0 (50).8 (6) 5765 6C9. (7) 0.8 (9).86 (7.7) 0.7 (7).7 (9). (0) 0. (7).85 (7.).6 (6) 0.7 (7).0 (50).8 (6) 5765 9C9. (7).0 (). (58.9 0.6 (5). (86). (0) 0. (7).85 (7.).6 (6) 0.8 (9).7 ().9 (8) For replacement valve (less base), order model 5760. ccessories Electrical Connectors Silencers Electrical Cord Electrical Connector Model Number Cord Connector Electrical Connector Type Length Diameter Without Lighted Connector Form meter (feet) Light Volts DC 0 Volts C DIN 650 Form Prewired Connector (8 gauge) (6/) 6-mm 7K77 70K77-W 70K77-Z DIN 650 Form Prewired Connector (8 gauge) (6/) 0-mm 7K77 8K77-W 8K77-Z DIN 650 Form Connector for threaded conduit (/ inch electrical conduit fittings) 7K77 7K77-W 7K77-Z DIN 650 Form Connector Only 97K87 96K87-W 96K87-Z Port Thread Model vg. Dimensions inches (mm) Weight Size Type Number* C V Length Width lb (kg) / Male 550000.7. ().6 (9) 0. (0.) / Male 550050 5.. ().6 (9) 0. (0.) / Male 5500500.5.0 (5) 5. (5) 0.6 (0.) Male 5500600.6.0 (5) 5. (8) 0.6 (0.) Conditions at Start: Inlet is closed to outlet by both valve elements and. Outlet is open to exhaust. Pressure signals at both switches SW and SW are exhausted. Contacts and of switches SW and SW are connected. SW VLVE OPERTION C D SW Normal Operation: Simultaneously energizing both solenoids actuates both pilots and causes valve elements and to shift. Inlet is then connected to outlet via crossflow passages C and D. Exhaust is closed. Sensing pressure signals go to each pressure switch and become equal to inlet pressure. oth switches trip and now contacts and of switches SW and SW are connected instead of contacts and. SW SW Completion of Normal Cycle: Simultaneously de-energizing both solenoids returns the valve to the Conditions at Start described at left. Detecting a Malfunction: malfunction in the system or the valve itself could cause one valve element to be open and the other closed. ir then flows past the inlet poppet on valve element, into crossflow passage D, but is substantially blocked by the spool portion of element. The large size of the open exhaust passage past element keeps the pressure at the outlet port below % of inlet pressure. Full sensing air pressure from side goes to switch SW, and a reduced pressure goes to switch SW. This full pressure signal causes switch SW to trip. Switch SW, with a reduced pressure signal, does not trip. n external monitoring system can detect the malfunction by C D monitoring the condition of the switches SW and SW. The external monitoring system may then react accordingly by shutting down the power to the valve solenoids and any other components deemed SW SW necessary to stop the machine. IMPORTNT NOTE: Please read carefully and thoroughly all of the CUTIONS, WRNINS on the inside back cover..6 05, ROSS CONTROLS. ll Rights Reserved.

SERPR Crossflow Double Valves with Pressure Switches, Size 5 Series Port Size asic Size Model Number* Flanged Ports With Overrides Without Overrides - - C V Weight lb (kg) /8 57C70** 57C76** 7 8. (.8) / 57C70** 57C76** 9 8. (.8) / 57C50** 57C56** 8. (.8) * NPT port threads. For SPP threads, add a D prefix to the model number, e.g., D57C70W. ** Insert voltage code: W = volts DC; Z = 0-0 volts C, 50/60 Hz; e.g., 57C70W. For other voltages consult ROSS. Valve and base can be ordered separately, consult ROSS. EMIII HZ 9770 COIL COIL Signal Signal Valve Dimensions inches (mm) Pressure Switches & Monitoring: Valves with pressure switches must be used in conjunction with an external monitoring device to assist with OSH compliance (Ref. 90.7). The valves on this page do not have a built-in monitor, and so must only be used in conjunction with an external monitoring system. Such monitoring system must be capable of inhibiting the operation of the valve and associated machinery in the event of a failure within the valve. CUTION: If the system must be reset, electrical signals to both solenoids must be removed to prevent the machine from immediately recycling and producing a potentially hazardous condition..7 (9) Threaded-port model 7. (89) Flanged-port model /8 - / 8. (09) Flanged-port model / 7. (85) 6. (55) ccessories Electrical Connectors VLVE OPERTION Electrical Cord Electrical Connector Model Number Cord Connector Electrical Connector Type Length Diameter Without Lighted Connector Form meter (feet) Light Volts DC 0 Volts C DIN 650 Form Prewired Connector (8 gauge) (6/) 6-mm 7K77 70K77-W 70K77-Z DIN 650 Form Prewired Connector (8 gauge) (6/) 0-mm 7K77 8K77-W 8K77-Z DIN 650 Form Connector for threaded conduit (/ inch electrical conduit fittings) 7K77 7K77-W 7K77-Z DIN 650 Form Connector Only 97K87 96K87-W 96K87-Z Refer to page.9. STNDRD SPECIFICTIONS (for valves on this page): Construction: Dual poppet. Mounting Type: Inline. Pilot Solenoids: Two, rated for continuous duty. tandard Voltages: volts DC; 0-0 volts C, 50/60 Hz. Voltages at pressure switches must not exceed 50 volts. Power Consumption (each solenoid): 5 V maximum in-rush, V holding on 50 or 60 Hz; watts nominal on DC. Electrical Connections: Uses cord-grip connectors at solenoids. Connectors according to DIN 650 (ISO 00). Enclosure Rating: IP 65 according to IEC-Publication and DIN 0050, Sheet. mbient Temperature: 0 to 0 F ( to 50 C). Media Temperature: 0 to 75 F ( to 80 C). Flow Media: Filtered air. Inlet Pressure: 0 to 50 psig (.5 to 0 bar). Functional Safety Data: Category PL e; 0d: 0,000,000; PFHd: 7.7x0-9 ; MTTFd: 0.9 (n op: 6600). Certifications: CE Marked for applicable directives,, CS/UL. Vibration/Impact Resistance: Tested to S EN 60068--7. IMPORTNT NOTE: Please read carefully and thoroughly all of the CUTIONS, WRNINS on the inside back cover..7

SERPR Crossflow Double Valves with Pressure Switches, Size 8,, & 0 5 Series Port Size asic Size Model Number* C V Weight lb (kg) Flanged Ports - - / 8 5768**.5 0. (5.) / 8 57568**. (5.) 8 57668**. (5.) / 5756** 8 5 5. (7.0) 5766** 8.5 9 5. (7.0) / 5776** 9.0 5. (7.0) / 0 57760** 0.9 (5.) / 0 57860**.9 (5.) EMIII HZ 9770 * NPT port threads. For SPP threads, add a D prefix to the model number, e.g., D5768W. ** Insert voltage code: W = volts DC; Z = 0-0 volts C, 50/60 Hz; e.g., 5768W. For other voltages consult ROSS. Valve and base can be ordered separately, consult ROSS. COIL Signal COIL Signal Pressure Switches & Monitoring: Valves with pressure switches must be used in conjunction with an external monitoring device to assist with OSH compliance (Ref. 90.7). The valves on this page do not have a built-in monitor, and so must only be used in conjunction with an external monitoring system. Such monitoring system must be capable of inhibiting the operation of the valve and associated machinery in the event of a failure within the valve. CUTION: If the system must be reset, electrical signals to both solenoids must be removed to prevent the machine from immediately recycling and producing a potentially hazardous condition. Valve Dimensions inches (mm). (8) asic Size 8 6.7 (7) Treaded-port model 8.8 () Flanged-port model 7. (8) STNDRD SPECIFICTIONS (for valves on this page): Construction: Dual poppet. Mounting Type: Inline. Pilot Solenoids: Two, rated for continuous duty. Standard Voltages: volts DC; 0-0 volts C, 50/60 Hz. Voltages at pressure switches must not exceed 50 volts. Power Consumption (each solenoid): 87 V maximum in-rush, 0 V holding on 50 or 60 Hz; watts nominal on DC. Electrical Connections: Uses cord-grip connectors at solenoids. Connectors according to DIN 650 (ISO 00). Enclosure Rating: IP 65 according to IEC-Publication and DIN 0050, Sheet. mbient Temperature: 0 to 0 F ( to 50 C). Media Temperature: 0 to 75 F ( to 80 C). Flow Media: Filtered air. Inlet Pressure: 0 to 5 psig ( to 8.5 bar). Functional Safety Data: Category PL e; 0d: 0,000,000; PFHd: 7.7x0-9 ; MTTFd: 0.9 (n op: 6600). Certifications: CE Marked for applicable directives,, CS/UL. Vibration/Impact Resistance: Tested to S EN 60068--7. IMPORTNT NOTE: Please read carefully and thoroughly all of the CUTIONS, WRNINS on the inside back cover..8 05, ROSS CONTROLS. ll Rights Reserved.

SERPR Crossflow Double Valves with Pressure Switches, Size 8,, & 0 5 Series Valve Technical Data & Operation Valve Dimensions inches (mm) 6.5 (0) asic Size. (6) asic Size 0 7.0 (78) Treaded-port model 9. (0) Flanged-port model 8.6 (9) 0. (67) Treaded-port model. (5) Flanged-port model. (8) ccessories Electrical Connectors Electrical Cord Electrical Connector Model Number Cord Connector Electrical Connector Type Length Diameter Without Lighted Connector Form meter (feet) Light Volts DC 0 Volts C DIN 650 Form Prewired Connector (8 gauge) (6/) 6-mm 7K77 70K77-W 70K77-Z DIN 650 Form Prewired Connector (8 gauge) (6/) 0-mm 7K77 8K77-W 8K77-Z DIN 650 Form Connector for threaded conduit (/ inch electrical conduit fittings) 7K77 7K77-W 7K77-Z DIN 650 Form Connector Only 97K87 96K87-W 96K87-Z VLVE OPERTION Conditions at Start: Inlet is closed to outlet by both valve elements and. Outlet is open to exhaust. Pressure signals at both switches SW and SW are exhausted. Contacts and of switches SW and SW are connected. Normal Operation: Simultaneously energizing both solenoids actuates both pilots and causes valve elements and to shift. Inlet is then connected to outlet via crossflow passages C and D. Exhaust is closed. Sensing pressure signals go to each pressure switch and become equal to inlet pressure. oth switches trip and now contacts and of switches SW and SW are connected instead of contacts and. SW SW SW C D SW Completion of Normal Cycle: Simultaneously de-energizing both solenoids returns the valve to the Conditions at Start described at left. Detecting a Malfunction: malfunction in the system or the valve itself could cause one valve element to be open and the other closed. ir then flows past the inlet poppet on valve element, into crossflow passage D, but is substantially blocked by the spool portion of element. The large size of the open exhaust passage past element keeps the pressure at the outlet port below % of inlet pressure. Full sensing air pressure from side goes to switch SW, and a reduced pressure goes to switch SW. This full pressure signal causes switch SW to trip. Switch SW, with a reduced pressure signal, does not trip. n external monitoring system can detect the malfunction by monitoring the condition of the switches SW and SW. The external monitoring system may then react accordingly by shutting down the power to the valve solenoids and any other components deemed necessary to stop the machine. SW C D SW IMPORTNT NOTE: Please read carefully and thoroughly all of the CUTIONS, WRNINS on the inside back cover..9

eneral Information Standard Specifications The standard specifications for the products on each page of this catalog are given on the same page or referenced. For solenoid pilot valves, models with internal pilot supply are listed. Most models are also available for use with external pilot supply or have a built-in pilot supply selector valve. The products in this catalog are intended for use in industrial pneumatic systems. Most products are adaptable to other uses and conditions not covered by the standard specifications given in this catalog. Weights shown are approximate and are subject to change. Dimensions given, unless otherwise noted, are envelope dimensions (not for mounting). Consult ROSS for further information. Port Threads Ports of valves and bases described in this catalog have NPT (NSI.) threads. Other thread types can be specified by putting an appropriate prefix letter on the model or part number when ordering. Thread Types by Model Prefix Letter Pneumatic Port Prefix Threaded Electrical Threads Letter Opening NPT (NSI.) None NPT ISO 8 - DIN 59 rallel, SPP # C* ISO 8 - DIN 59 rallel, SPP # D ISO 8 - JIS 00 Tapered # J ISO SE 96- ISO 96 S NPT * Used only for filters, regulators, lubricators. # ISO 8 threads superseds SPP, and JIS thread types. Flow Ratings Flow ratings are expressed as C V where C V = corresponds to a steady state air flow of approximately scfm under the following conditions: Inlet pressure = 00 psig (6.7 bar) Pressure drop = 0 psi (0.69 bar) ir temperature = 68 F (0 C) Relative humidity = 6 percent Note: ecause widely differing test standards are used to measure C V values, the figures given in this catalog should not be used to compare ROSS valves with those of other makers. The C V ratings given here are intended only for use with performance charts published by ROSS. The C V ratings are averages for the various flow paths through the valve and are for steady flow conditions. pprovals and Certifications ROSS products are designed to meet a number of industrial standards, including the Canadian Standards ssociation (C.S..) guidelines. For more information on specific product approvals, contact your local distributor or ROSS. Solenoids ll ROSS standard solenoids are rated for continuous duty (unless noted otherwise) and will operate the valve within the air pressure range specified in this catalog. Explosion-Proof Solenoid Pilot available, for more information consult ROSS. Voltage & Hertz When ordering a solenoid valve, also specify the desired solenoid voltage and hertz. Voltage Types by Model Suffix Letter Voltage Suffix Letter 0 volts C Z 0 volts C Y volts DC H volts DC W 8 volts DC M 90 volts DC K 0 volts DC P 5 volts DC C Recommended Solenoid Voltages: 00-0 volts, 50 Hz; 00-0 volts, 60 Hz; volts DC; 0 volts DC. In addition, the following voltages are available: 00, 0 volts, 50 Hz 00, 0, 80 volts, 60 Hz, 8, 0 volts, 50 Hz 0 volts, 60 Hz 00, 0 volts, 50 Hz 00, 0 volts, 60 Hz. For example: Model 77500, 0 volts, 60 Hz. Model W60760, 0 volts, 50 Hz. Please note that not all configurations are available for all models. For additional information or help with voltage configuration, please contact your local distributor or ROSS. Port Identification Valve symbols in this catalog conform to the ISO 9-:99 standard of the International Organization for Standardization (ISO) and the SE J05 standard of the Society of utomotive Engineers (SE) respectively. Information or Technical ssistance For additional information or application assistance concerning ROSS products, consult ROSS or your local ROSS distributor (see contact information on the back cover). Order Placement For order placement, consult ROSS or your local ROSS distributor. For a current list of countries and local distributors, visit ROSS website at. 05, ROSS CONTROLS. Content subject to change.

CUTIONS, WRNINS and STNDRD WRRNTY PRE-INSTLLTION or SERVICE. efore servicing a valve or other pneumatic component, be sure that all sources of energy are turned off, the entire pneumatic system is shut off and exhausted, and all power sources are locked out (ref: OSH 90.7, EN 07).. ll ROSS products, including service kits and parts, should be installed and/or serviced only by persons having training and experience with pneumatic equipment. ecause any installation can be tampered with or need servicing after installation, persons responsible for the safety of others or the care of equipment must check every installation on a regular basis and perform all necessary maintenance.. ll applicable instructions should be read and complied with before using any fluid power system in order to prevent harm to persons or equipment. In addition, overhauled or serviced valves must be functionally tested prior to installation and use.. Each ROSS product should be used within its specification limits. In addition, use only ROSS parts to repair ROSS products. WRNIN: Failure to follow these directions can adversely affect the performance of the product or result in the potential for human injury or damage to property. FILTRTION and LURICTION 5. Dirt, scale, moisture, etc. are present in virtually every air system. lthough some valves are more tolerant of these contaminants than others, best performance will be realized if a filter is installed to clean the air supply, thus preventing contaminants from interfering with the proper performance of the equipment. ROSS recommends a filter with a 5-micron rating for normal applications. 6. ll standard ROSS filters and lubricators with polycarbonate plastic bowls are designed for compressed air applications only. Do not fail to use the metal bowl guard, where provided, to minimize danger from high pressure fragmentation in the event of bowl failure. Do not expose these products to certain fluids, such as alcohol or liquefied petroleum gas, as they can cause bowls to rupture, creating a combustible condition, hazardous leakage, and the potential for human injury or damage to property. Immediately replace a crazed, cracked, or deteriorated bowl. When bowl gets dirty, replace it or wipe it with a clean dry cloth. 7. Only use lubricants which are compatible with materials used in the valves and other components in the system. Normally, compatible lubricants are petroleum based oils with oxidation inhibitors, an aniline point between 80 F (8 C) and 0 F (0 C), and an ISO, or lighter, viscosity. void oils with phosphate type additives which can harm polyurethane components, potentially leading to valve failure which risks human injury, and/or damage to property. VOID INTKE/EXHUST RESTRICTION 8. Do not restrict the air flow in the supply line. To do so could reduce the pressure of the supply air below the minimum requirements for the valve and thereby cause erratic action. 9. Do not restrict a valve s exhaust port as this can adversely affect its operation. Exhaust silencers must be resistant to clogging and must have flow capacities at least as great as the exhaust capacities of the valves. Contamination of the silencer can result in reduced flow and increased back pressure. WRNIN: ROSS expressly disclaims all warranties and responsibility for any unsatisfactory performance or injuries caused by the use of the wrong type, wrong size, or an inadequately maintained silencer installed with a ROSS product. POWER PRESSES 0. Mechanical power presses and other potentially hazardous machinery using a pneumatically controlled clutch and brake mechanism must use a press control double valve with a monitoring device. double valve without a self-contained monitoring device should be used only in conjunction with a control system which assures monitoring of the valve. ll double valve installations involving hazardous applications should incorporate a monitoring system which inhibits further operation of the valve and machine in the event of a failure within the valve mechanism. ENERY ISOLTION/EMERENCY STOP. Per specifications and regulations, ROSS L-O-X and L-O-X with EEZ-ON operation products are defined as energy isolation devices, NOT S EMERENCY STOP DEVICES. ll products sold by ROSS CONTROLS are warranted for a one-year period [with the exception of all Filters, Regulators and Lubricators ( FRLs ) which are STNDRD WRRNTY warranted for a period of seven years] from the date of purchase to be free of defects in material and workmanship. ROSS obligation under this warranty is limited to repair or replacement of the product or refund of the purchase price paid solely at the discretion of ROSS and provided such product is returned to ROSS freight prepaid and upon examination by ROSS is found to be defective. This warranty becomes void in the event that product has been subject to misuse, misapplication, improper maintenance, modification or tampering. THE WRRNTY EXPRESSED OVE IS IN LIEU OF ND EXCLUSIVE OF LL OTHER WRRNTIES ND ROSS EXPRESSLY DISCLIMS LL OTHER WRRNTIES EITHER EXPRESSED OR IMPLIED WITH RESPECT TO MERCHNTILITY OR FITNESS FOR PRTICULR PURPOSE. ROSS MKES NO WRRNTY WITH RESPECT TO ITS PRODUCTS MEETIN THE PROVISIONS OF NY OVERNMENTL OCCUPTIONL SFETY ND/OR HELTH LWS OR REULTIONS. IN NO EVENT IS ROSS LILE TO PURCHSER, USER, THEIR EMPLOYEES OR OTHERS FOR INCIDENTL OR CONSEQUENTIL DMES WHICH MY RESULT FROM RECH OF THE WRRNTY DESCRIED OVE OR THE USE OR MISUSE OF THE PRODUCTS. NO STTEMENT OF NY REPRESENTTIVE OR EMPLOYEE OF ROSS MY EXTEND THE LIILITY OF ROSS S SET FORTH HEREIN.

ROSS CONTROLS U.S.. Tel: +-8-76-800 Customer Svs. -800-ET-ROSS Technical Svs. -888-TEK-ROSS sales@rosscontrols.com ROSS EUROP mbh ermany Tel: +9-60-7597-0 sales@rosseuropa.com www.rosseuropa.com ROSS SI K.K. Japan Tel: +8--778-75 www.rossasia.co.jp ROSS UK Ltd. United Kingdom Tel: +-5-6795 sales.uk@rosscontrols.com www.rossuk.co.uk ROSS CONTROLS INDI Pvt. Ltd. India Tel: +9--6-900 ross.chennai@rosscontrols.com ROSS SOUTH MERIC Ltda. razil Tel: +55--5-00 vendas@rosscontrols.com DIMFLUID s.a.s. France Tel: +--9-5-65-65 www.dimafluid.com ROSS CONTROLS (CHIN) Ltd. China Tel: +86--695-796 sales@rosscontrols.com.cn www.rosscontrolschina.com Full-Service lobal Locations There are ROSS Distributors Throughout the World To meet your requirements across the globe, ROSS distributors are located throughout the world. Through ROSS or its distributors, guidance is available for the selection of ROSS products, both for those using pneumatic components for the first time and those designing complex pneumatic systems. Other literature is available for engineering, maintenance, and service requirements. If you need products or specifications not shown here, please contact ROSS or your ROSS distributor. They will be happy to assist you in selecting the best product for your application. For a current list of countries and local distributors, visit ROSS website at. Printed in the U.S.. - Rev. 09/5 Content subject to change. 05, ROSS CONTROLS. ll Rights Reserved. Form ROSS-PRS0