GRUNDFOS DATA BOOKLET MD.15.3.4 3x4V Grundfos pump 979187 Thank you for your interest in our products. Please contact us for more information, or visit our website https://www.lenntech.com/grundfos/muldoub/979187/md-15-3-4.html info@lenntech.com tel. +31 152 61 9 fax. +31 152 616 289 BE > THINK > INNOVATE
Position Qty. Description 1 MD.15.3.4 Product No.: On request Note! Product picture may differ from actual product Supplied as complete unit ready for installation, the Multilift consist of a fully integrated collecting tank with two pumps and submersible motors, non-return valve with integrated Y-branch pipe, discharge adapter with flexible connection piece DN1 mounted on the collecting tank and a pre-wired Controller incl. a level sensor. The fully integrated collecting tank has all necessary ports for the connection of inlet pipe, discharge pipe, vent pipe and a manually operated diaphragm pump (accessory). The collecting tank contains 8 inlet sockets around it's shape. The back inlet DN1 is placed on a patented inlet disk to connect all inlet pipe levels (centre) between 18 and 315mm stepless. DN1 and DN inlet sockets on each side. 2 x DN1, DN sockets on the top of the tank. Multilift corrosion free polyethylen collecting tanks are gas- and odour-proof as well as watertight, reduction of residual water and less sedimentation by chamfered bottom design. Pumps with Vortex impeller and a maintenance free submersible motors, oil chamber with physiological harmless oil filling between two shaft seals. Direction of rotation can be observed from outside over the shaft below the eye bolt. An LC221 controller with microprocessor is equipped with display for full monitoring possibilities. The pump and sensor are connected to the controller with 4m or 1m cable and tube length. The power supply cable is 1,5m with plug (incl. phase inverter for 3 phase motor) Contactless, piezo resistive pressure sensor pluggable inside the cabinet, monitored by controller, accurate to the millimetre shown on display. Blockage free pressure tube inside the tank without movable parts inside wastewater. The controller offer thermal motor protection and monitoring of pump operation. The thermal motor protection consists of thermal switches in the winding. Controller functions: on/off, regular and failure changeover of two wastewater pumps based on a continuous signal from a piezo-resistive sensor motor protection via motor-protective circuit breaker and/or current measurement as well as connection of thermal switches. dry running motor protection via run-time limitation with a following emergency operation 24h automatic test runs during long periods of inactivity setting of delay times: - stopping delay (time from the stop level is reached till the pumped is stopped) - starting delay (time from the start level is reached till the pumped is started) - alarm delay (time from a fault appears till an alarm is indicated) to prevents short-time high-level alarm in case of temporary high inflow to the tank. automatic current measurement for alarm indications 1/9
Position Qty. Description operating indication of: - operating mode (auto, manual) - operating hours - impulses (number of starts) - highest measured motor current alarm indication of: - pump status (running, fault) - phase-sequence fault and missing phase - thermal-switch failure - high-water alarm - time for service/maintenance (selectable). selection of automatic alarm resetting fault log of up to 2 alarms selection between different start levels selection of connected sensor type calibration of sensor (preset) selection of maintenance interval (, 3, 6 or 12 months). As standard, the LC 221 has 6 potential-free outputs for: pump running pump failure high water-level alarm common fault. 6 digital inputs for the following functions: connecting a pressure sensor board (pre-assembled) connecting an analogue sensor (4-2mA or -5V) connecting up to four level switches or pressure switches instead of analogue sensor connecting a separate level switch to be used for flood detection outside the Multilift. Lifting stations are often installed in a sump inside the basement - the lowest point in the building. In case of e.g. groundwater inflow or water pipe burst, an alarm will be indicated by the controller. connecting an external alarm reset connecting the thermal switch of the motor. The Multilift range is designed due to the standard EN12-1, approved and monitored by external institute LGA. Further approvals are VDE, GHOST, CB, EMV Controls: Type of control box: LC221.2 Liquid: Liquid temperature range: C.. 4 C Density: 998.2 kg/m³ Technical: Type of impeller: VORTEX Maximum particle size: mm Approvals on nameplate: EN 12-1 Valve type: FLAP VALVE Materials: Impeller: Tank: Gasket: LURANYL LDPE NBR Installation: Pump outlet: 8 Electrical data: Power input - P1: Rated power - P2: Mains frequency: Rated voltage: 2 x 2.1 kw 2 x 1.7 kw Hz 3 x 4 V 2/9
Position Qty. Description Voltage tolerance: +1/-14 % Max starts per. hour: 6 Rated current: 2 X 4,1 A Cos phi - power factor:.8 Rated speed: 142 rpm Motor efficiency at full load: 8.5 % Number of poles: 4 Start. method: direct-on-line Enclosure class (IEC 34-5): IP68 Insulation class (IEC 85): F Type of cable plug: CEE 3P+N+E Mains cable: 1.5 m Tank: Total volume of tank(s): 13 l Total effective volume of collecting tank at 18 mm inlet: Total effective volume of collecting tank at 2 mm inlet: Total effective volume of collecting tank at 315 mm inlet: 49 l 69 l 86 l Others: Net weight: 119 kg 3/9
On request MD.15.3.4 Hz H [m] MD.15.3.4, 3*4 V, Hz eta [%] 1 9 8 7 6 6 5 4 4 3 3 2 2 1 1 1 2 3 4 5 6 7 8 9 1 11 12 13 14 15 P1 [kw] 2.4 2.2 2. 1.8 1.6 1.4 1.2 1..8.6.4.2 Q [l/s] 4/9
868 418 818 DN8 75 DN7 / 16 DN1 / 1 16 DN1 3 / 11 DN1 DN 123 178 / / DN / DN 434 / 178 DN / 11 DN1 123 / 11 DN1 / Description Value General information: Product name: MD.15.3.4 Product No: On request EAN number: On request Technical: Max flow: 15.3 l/s Head max: 9.4 m Type of impeller: VORTEX Maximum particle size: mm Approvals on nameplate: EN 12-1 Valve type: FLAP VALVE Materials: Impeller: LURANYL Tank: LDPE Gasket: NBR Installation: Pump outlet: 8 Liquid: Liquid temperature range: C.. 4 C Density: 998.2 kg/m³ Electrical data: Power input - P1: 2 x 2.1 kw Rated power - P2: 2 x 1.7 kw Mains frequency: Hz Rated voltage: 3 x 4 V Voltage tolerance: +1/-14 % Max starts per. hour: 6 Rated current: 2 X 4,1 A Cos phi - power factor:.8 Rated speed: 142 rpm Motor efficiency at full load: 8.5 % Number of poles: 4 Start. method: direct-on-line Enclosure class (IEC 34-5): IP68 Insulation class (IEC 85): F Motor protec: BIMETAL THERMAL SWITCH Thermal protec: BIMETAL THERMAL SWITCH Motor cable: 4 m Cable type: H7 RN-F Type of cable plug: CEE 3P+N+E Mains cable: 1.5 m Cable size: 4X1,5+2X1 Mains cable: H5 VV-F Controls: Type of control box: LC221.2 Operation mode: S3-%,1MIN Tank: Total volume of tank(s): 13 l Total effective volume of collecting tank at 18 mm inlet: Total effective volume of collecting tank at 2 mm inlet: Total effective volume of collecting tank at 315 mm inlet: Others: Net weight: 49 l 69 l 86 l 119 kg 2 H [m] 1 9 8 7 6 5 4 3 2 1 MD.15.3.4, 3*4 V, Hz 2 4 6 8 1 12 14 P1 [kw] 12 2. 1.5 1..5 123 DN1 / 178 DN / DN1 / 11 DN / 11 123 178 12 DN1 / 2 DN7 / DN1 / 5 551 16 188 32 16 75 11 434 DN / DN / 3 3 1 418 818 868 DN8 Q [l/s] 18 16 164 315 2 458 366 DN1 / 32 722 eta [%] 6 4 3 2 1 16 5/9
On request MD.15.3.4 Hz DN1 / 11 12 2 18 315 2 123 DN1 / 178 DN / 11 458 366 434 DN / DN / 3 3 1 DN1 / 16 DN7 / 75 164 32 32 16 188 16 12 2 5 551 DN1 / 11 123 DN / 178 DN1 / 16 722 418 818 868 DN8 Note! All units are in [mm] unless others are stated. Disclaimer: This simplified dimensional drawing does not show all details. 6/9
Exploded view 251a 251d 77 28 7 7a 17 31a 219 92 31a 11 9 92 51 11b 15 1 215a 215 66a 67 49 45 18 53a 53 215a 217 531a 534 531 534a 6 7/9
Sectional drawing (TM582 for TPE2,TPE3) 5 4 3 2 1 TM582 8/9
Exploded view ( TM5726 for MGE model H/I ) 251d 251b 291 29 293 287 287a 2 277a 273b 277 252a 286 273a 273 275a 266 268 268a 289a 289 251a 288b 288 288a 252b 159e 157 158 1 156c 156 151 152 172 154 185 178 156d 187 153 188 191 156c 156b 192 159d 9/9
Disclaimer: The information about the Grundfos pump in this document may be outdated. Data may be subject to alterations without further notice. Please contact us to verify the data above is still accurate/up-to-date. All information is copyright Grundfos. info@lenntech.com https://www.lenntech.com tel. +31 152 61 9 fax. +31 152 616 289