Instruction Sheet P/N 0870G0 WARNING: Allow only qualified personnel to perform the following tasks. Follow the safety instructions in this document and all other related documentation. Introduction The spray pressure control (SPC) manifold is part of the Nordson Spray Pressure Control system. The manifold houses a fixed orifice (restrictor) that reduces pressure fluctuations in the fluid system. A T-filter is mounted on the manifold upstream from the orifice to prevent contaminants from blocking it. Figure (Shown with Drip Tray) Part 0870G0
Installation See Figure for a typical dual spray gun system using Spray Pressure Control. Review this recommended plumbing circuit before installing any parts into the system. Additional customer-supplied parts may be required. 6 7 DRAIN DRAIN SUPPLY DRAIN 0 9 8 Figure Recommended Circuit for Spray Pressure Control. Nordson EP Pump. Pressure-reducing regulator. Two-way ball valve 6. Spray gun. Heater 7. SPC manifold assembly. Filter 8. Back pressure regulator 9. Two-way ball valve 0. Three-way ball valve (drain) Part 0870G0
Installation WARNING: Relieve system fluid pressure before installing the SPC manifold. Failure to observe this warning may cause personal injury or equipment damage. NOTE: Restrictors are not included with the SPC manifold, as they are application-specific. Refer to Restrictors on page 6 for a list of available restrictors.. See Figure. Install the manifold with the drain nipple () pointing down.. Connect a fluid line from the spray gun output to the inlet connector ().. Connect a fluid line from the outlet connector () to the fluid return line to the pump.. After you have installed the manifold, flush the fluid delivery system to remove any contaminants from the system.. Remove the restrictor holder (), install a restrictor and seal (), then install the holder back in the manifold. See Figure for restrictor installation. Figure Installation. Outlet connector. Inlet connector. Drain nipple. Restrictor and seal. Restrictor holder Part 0870G0
SPC Manifold Parts See Figure. Item Part Description Quantity Note 90 MANIFOLD, circulation assembly 7900 FILTER, liquid, / in. NPT, stainless steel, T-type A 7967 GASKET, filter, liquid, stainless steel, Type-TF A 9797 NIPPLE, hex, / 8 x / x.06 in., stainless steel - - - - - - BLOCK, orifice 696 HOLDER, restrictor, mini-insert B 9709 NIPPLE, hex, / 8 x / 8 x. in., stainless steel 6 976 NIPPLE, extra heavy, / 8 x.0 in., stainless steel 7 767 VALVE, ball, -way, stainless steel 8 97099 CONNECTOR, male, 7, / -0 x / 8 in. NPT, stainless steel 9 9709 CONNECTOR, male, 7, / -0 x / in., stainless steel 0 6966 FILTER ELEMENT, 0 micron A 0 BRACKET, drip tray, universal, SPC 980 SCREW, hex, / -0 x.7 in., cap, zinc 980 NUT, jam, / -0, steel, zinc 980 WASHER, lock, split, / in., steel, zinc NOTE A: Included in T-Filter Cleaning Kit, part 090. B: The restrictor holder does not include a restrictor or O-rings. Refer to Restrictors on page 6 to select the appropriate restrictor for your application and to order restrictor holder O-rings and backup ring. Part 0870G0
9 A 0 8 7 6 Park filter cap on drip tray while changing filter Drip Tray Mounting Options Figure SPC Manifold Parts Part 0870G0
6 Restrictors for SPC Manifolds Restrictors are not included with the SPC manifold. Select the appropriate restrictor for your application. NOTE: See Figure. A seal (item ) is included with all restrictors. Restrictor Flow Rate (gpm) Orifice Size Part Number H 0 @00 psi 8 0.008 0.0 067 0.00 0.0 0077 0.0 0.06 0077 0.0 0.09 0 0.0 0. 6 0.00 0. 0.0 0. 7 0.0 0.9 Restrictor Acessory Group See Figure. This kit contains a 0.00 restrictor, restrictor seal, and the restrictor holder O-rings and backup ring. Use this list to order replacement restrictor seals (all restrictors include the listed seal), and the restrictor holder O-rings and backup ring. Item Part Description Quantity Note 7966 ACCESSORY group, MI, M, 0.00 906 O-RING, Viton, black, / 6 -in. tube 908 BACK-UP RING, single, / 6 x 7 / 6 in. 90 O-RING, Viton, black, 0. x 0.8 in. 067 RESTRICTOR, MI, M, 0.00 in. orifice 709 SEAL, ring, M Figure Restrictor Accessory Group Issued /08 Original copyright date 99. MEG, Nordson, and the Nordson logo are registered trademarks of Nordson Corporation. Viton is a registered trademark of DuPont Dow Elastomers. L.L.C. Part 0870G0