SYSTEM ACCESSORIES SECTI 6 VACUSTAT, PRESSURE SENSORS, VACUUM SENSORS, & FILTERS 6 2012 EDCO USA. www.edcousa.net 6:1
6 SYSTEM ACCESSORIES CTENTS VACUSTAT MECHANICAL PRESSURE SWITCH INLINE VACUUM FILTER MECHANICAL VACUUM SWITCH 602-SERIES DIGITAL PRESSURE & VACUUM SENSORS T-STYLE VACUUM FILTER DVN-100-4 V-STYLE VACUUM SENSOR 61-SERIES & 62-SERIES DIGITAL VACUUM SENSORS VACUUM SYSTEM ACCESSORIES Vacustat 6:3 6:4 Mechanical Pressure Switches 6:5 Mechanical Vacuum Switches 6:6 V-Style Vacuum Sensors 6:7 61-Series & 62-Series Digital Vacuum Sensors 6:8 DVN-100-4 6:9 200-Series Pressure & Vacuum Sensors 6:10 602-Series Pressure & Vacuum Sensors 6:11 T-Style Vacuum Filters 6:12 Inline Vacuum Filters 6:12 200-SERIES DIGITAL PRESSURE & VACUUM SENSORS 6:2 2012 EDCO USA. www.edcousa.net
VACUSTAT The Vacustat is the basis for energy-saver controls and is used with any suitable vacuum pump in conjunction with a vacuum check valve. Vacuum pumps that are equipped with an integral non-return valve or a vacuum pump and external vacuum check valve such as VC18 fit the requirements for a vacustat control. As always, energy-saver controls can only be used in leak-free systems and some provision must be made to dissipate the checked vacuum and release the work piece when desired. VU-18F is an adjustable vacuum-controlled 2/2 valve that supplies compressed air to the vacuum pump whenever system vacuum level is shallower than the Vacustat set point. When the set point is achieved, the Vacustat shuts off the pump air supply until system vacuum level again requires replenishment. Weight: lb. (g) 0.23 (102) 6 HOW TO ORDER VU-18F PORT CNECTIS CODE FUNCTI Thread 1 Air Supply - Main 2 Vacuum Sense Port 3 Air Supply to Pump 0.23 [5.8] 1 2 3 0.95 [24.1] 0.36 [9.1] 0.71 [18] 1.06 [26.9] 1.55 [39.4] 0.2 [5.1] 0.7 [17.8] 1.2 [30.5] 1.4 [35.6] 1.26 [32] 0.31 [7.9] 1.9 [48.3] 1.68 [42.7] 3 0.95 [24.1] 1.72 [43.7] 1.32 [33.5] 0.95 [24.1] 0.18 [4.6] Thru Hole 2 Places 1 1.22 [31] 0.84 [21.3] 0.48 [12.2] 2 0.48 [12.2] Set Point Adjustment 0.13 [3.3] Thru Hole 2 Places 0.12 [3] 2012 EDCO USA. www.edcousa.net 6:3
6 VACUSTAT VACUSTAT MOUNTED AN AX-STYLE PUMP WITH N-RETURN VALVE Fittings and vacuum pump not included VACUSTAT MOUNTED A J-SERIES PUMP WITH N-RETURN VALVE Fittings and vacuum pump not included 6:4 2012 EDCO USA. www.edcousa.net
MECHANICAL PRESSURE SENSORS ELECTRICAL OUTPUT Electrical pressure sensors come with UL and CSA snap action silver contact SPDT (Single Pole Double Throw) switch with 0.187in (4.75mm) spade terminals. Triple terminal electrical connector and insulator kit for attaching wires is included. 1.00 [25.1] Set Point Adjustment 1.50 [38.1] 6 1.38 [35.1] 1/8 NPT 0.36 [9.1] 1.00 [25.4] 0.5 [12.7] OUTPUT PART NUMBER SPECIFICATIS ELECTRICAL PS18-E Pressure Adjustment Range: 10 to 140 psi (0.69 to 9.65 bar) N.C. PNEUMATIC PS18-NCL Temperature Range: -20 to +140 F (-29 to 60 C) N.O. PNEUMATIC PS18-NOP Electrical: 5 Amp @ 125 V AC, 250 V AC Maximum WEIGHT 2.3 oz (66g) Air Valve: 20 to 115 psi (1.4 to 7.9 bar); Cv = 6; 2.5 scfm (71 Nl/m) Construction: Housing: Zinc/Aluminum, Diaphram: Polymide, Spring: Stainless Steel. For Pneumatic Sensors: Port #1 - Air Supply ; Port #2 - Output Signal PNEUMATIC OUTPUT Pneumatic pressure sensors are available in normally-closed (NCL) and normallyopen (NOP) versions. Normally-closed (NCL) sensors open to pass air when the desired set point is achieved. Normallyopen sensors close to block air when the desired set point is achieved. Both versions have integral 5/32 (4mm) tube connectors. Set Point Adjustment 1.00 [25.4] 1.50 [38.1] 1.14 [29] 1.38 [35.1] 1/8 NPT 0.36 [9.1] 1.35 [34.3] 0.82 [20.8] 0.5 [12.7] 2012 EDCO USA. www.edcousa.net 6:5
6 MECHANICAL VACUUM SENSORS ELECTRICAL OUTPUT 1.38 [35.1] Electrical vacuum sensors come with UL and CSA snap action silver contact SPDT (Single Pole Double Throw) switch with 0.187in (4.75mm) spade terminals. Triple terminal electrical connector and insulator kit for attaching wires is included. 0.64 [16.3] 0.95 [24.1] 0.48 [12.2] 0.39 [9.9] 1.76 [44.7] 1/8 NPT Set Point Adjustment 0.3 [7.6] 0.5 [12.7] 0.72 [18.3] 0.3 [7.6] PNEUMATIC OUTPUT OUTPUT PART NUMBER SPECIFICATIS ELECTRICAL VSA18-E Vacuum Adjustment Range: -8 to -28 inhg (-27.1 to 94.8 kpa) N.C. PNEUMATIC VSA18-NCL Temperature Range: -20 to +140 F (-29 to 60 C) N.O. PNEUMATIC VSA18-NOP Electrical: 5 Amp @ 125 V AC, 250 V AC Maximum WEIGHT 2.1 oz (59g) Air Valve: 20 to 100 psi (1.4 to 6.9 bar); Cv = 6; 2.5 scfm (71 Nl/m) Construction: Housing: Aluminum, Diaphram: Nitrile, Spring: Stainless Steel. Pneumatic vacuum sensors are available in normally-closed (NCL) and normallyopen (NOP) versions. Normally-closed (NCL) sensors open to pass air when the desired set point is achieved. Normallyopen sensors close to block air when the desired set point is achieved. Both versions have integral 5/32 (4mm) tube connectors. For Pneumatic Sensors: Port #1 - Air Supply ; Port #2 - Output Signal 0.64 [16.3] 1.73 [43.9] 0.95 [24.1] 0.48 [12.2] 1.72 [43.7] 1.39 [35.3] 0.39 [9.9] 0.5 [12.7] 1.88 [47.8] 1/8 NPT Set Point Adjustment 0.3 [7.6] 0.72 0.3 0.47 [18.3] [7.6] [11.9] 6:6 2012 EDCO USA. www.edcousa.net
ELECTRIC SENSORS OPTIAL -18M MOUNT 0.72 [18.3] OUTPUT LED 0.3 [7.6] 0.4 [10.2] 0.68 [17.3] 1.01 [25.7] 0.26 [6.6] M5 x 0.8 6 150mm CABLE WITH 8mm MALE 3-PIN OR 4-PIN CNECTOR HOW TO ORDER OUTPUT V P - 4-18M A* = Analog 3 = 3-pin (Blank) = M5 x 0.8 (10-32 UNF) Male N = NPN 4 = 4-pin 18M = Male P = PNP CNECTOR MOUNTING THREADS *Analog output only available with 3-pin connector. ORDER CABLE SEPARATELY OUTPUT RATED PRESSURE -100kPa = 29.9" Hg = 100% VACUUM SET POINT ATMOSPHERIC PRESSURE: 0 kpa = 0" Hg = 0% VACUUM 3-PIN CABLES PART NUMBER 3QD2 3QD5 DESCRIPTI 3-pin, Quick Disconnect, 2 meter cable 3-pin, Quick Disconnect, 5 meter cable 4-PIN CABLES PART NUMBER Specifications Media Non lubricated air, Non-corrosive gas. Maximum Pressure 29 psi (200 kpa) Rated Pressure Range 0 ~ -29.5 inhg (0 ~ -100 kpa) Operating Temperature 14 ~ 122 (-10 ~ 60 ) Storage Temperature -4 ~ 158 (-20 ~ 70 ) Humidity 35 ~ 85% RH Electrical Connection -3: 3 pin pico 8 mm connector OR -4: 4 pin pico 8 mm connector Operating Voltage 10.8 ~ 30 V DC (including ripple) Current Consumption 20 ma maximum Display Red LED Circuit Analog, NPN, PNP Setting Accuracy ±3% F.S. max. Hysteresis Fixed, 2% F.S. max. Switching Capacity 30 VDC, 80 ma max. Response Time Approx. 1 ms Vibration 10 ~ 55 Hz 1.5 mm maximum, XYZ for 2 hrs Shock 1000 m/s 2, XYZ Insulation Resistance 100 MΩ minimum Dielectric Strength 500 V AC for 1 min. Analog Output Voltage 0 inhg (0 kpa) = 1 ± 4 V DC, -29.5 inhg (-100 kpa) = 5 ± 4 V DC NPN Output Voltage 0.8 V DC max. PNP Output Voltage 1.8 V DC max. 2012 EDCO USA. www.edcousa.net 6:7 4QD2 4QD5 DESCRIPTI 4-pin, Quick Disconnect, 2 meter cable 4-pin, Quick Disconnect, 5 meter cable ELECTRICAL CNECTI M8 Male Connector 3 3 - Pin 1. Brown Wire: +24 V DC 2. Black Wire: Output 3. Blue Wire: Common 4 - Pin 2 1 2 1. Brown Wire: +24 V DC 2. White Wire: Not Used 3. Blue Wire: Common 4. Black Wire: Output 4 3 1
6 DIGITAL SENSORS -18M Option 61 Output 1 Red LED 0.33 [8.4] Output Red LED Output 2 Green LED 0.87 [22.1] 0.49 [12.4] 0.12 [3.0] M3 x 0.5 2 Places 0.3 [7.6] 0.2 [5.1] 0.1 [2.5] 62 0.39 [9.9] 0.98 [24.9] 0.73 [18.5] 0.26 [6.6] -5F Option M5 x 0.8 (10-32 UNF) 0.18 [4.6] 0.13 [3.3] Thru Hole 2 Places 2.07 [52.6] 150mm CABLE WITH 8mm MALE 4-PIN CNECTOR ORDER CABLE SEPARATELY HOW TO ORDER OUTPUT NUMBER OF OUTPUTS MOUNTING THREADS DV P - 62-18M N = NPN 61 = 1 Output + Analog 5F = M5 x 0.8 (10-32 UNF) Female P = PNP 62 = 2 Outputs 18M = Male PART NUMBER Specifications Media Non lubricated air, Non-corrosive gas. ELECTRICAL CNECTI M8 Male 4-pin Connector Maximum Pressure 29 psi (200 kpa) Rated Pressure Range 0 ~ -29.5 inhg (0 ~ -100 kpa) Operating Temperature 14 ~ 140 (-10 ~ 60 ) 61 Storage Temperature -4 ~ 158 (-20 ~ 70 ) Humidity 35 ~ 85% RH 2 4 Electrical Connection 4 pin pico 8 mm connector Operating Voltage 10.8 ~ 26.4 V DC (including ripple) 1 3 Current Consumption 35 ma maximum Display 2-digit, 7 segment Red LED 1. Brown Wire: Power Supply Rated Display 0 ~ 99 2. White Wire: Analog Output Units Percent Vacuum (kpa) 3. Blue Wire: Common Output Display SET (1) - Red LED: SET 2 - Green LED Display Cycle 4 Hz 4. Black Wire: Output Resolution ±1 count Accuracy ±3% F.S. max. Hysteresis 61 - Adjustable approx. 0 ~ 15% F.S. : 62 - Fixed 2% F.S. max. 62 Switching Capacity 30 VDC, 80 ma max. Response Time Approx. 2 ms Vibration 10 ~ 500 Hz 1.5 mm maximum, XYZ for 2 hrs 2 4 Shock 196 m/s 2, XYZ Insulation Resistance 100 MΩ minimum 1 3 Dielectric Strength 500 V AC for 1 min. 1. Brown Wire: Power Supply Analog Output Voltage 0 inhg (0 kpa) = 1 ± 0.1 V DC, -29.5 inhg (-100 kpa) = 5 ± 0.2 V DC 2. White Wire: Output 2 Analog Output Current 1 ma max. Analog Hysteresis / Linearity ± 0.5% F.S. 3. Blue Wire: Common NPN Output Voltage 0.8 V DC max. 4. Black Wire: Output 1 PNP Output Voltage 1.2 V DC max. Thermal Error ±0.1% F.S./ max. in range of 0 ~ 50 (32 ~ 122 ) 6:8 2012 EDCO USA. www.edcousa.net 4QD2 4QD5 DESCRIPTI 4-pin, Quick Disconnect, 2 meter cable 4-pin, Quick Disconnect, 5 meter cable
DIGITAL SENSORS HOW TO ORDER DVN 100 4 Output 1 Red LED Male Output 2 Green LED Up Menu Selection Mode Down 1.11 [28.2] M5 x 0.8 (10-32 UNF) Female 6 0.49 [12.4] 0.39 [9.9] 0.63 [16] 0.31 [7.9] 0.31 [7.9] 2.29 [58.2] 2.76 [70.1] 0.31 [7.9] ORDER CABLE SEPARATELY OUTPUT PART NUMBER 4QD2 4QD5 DESCRIPTI 4-pin, Quick Disconnect, 2 meter cable 4-pin, Quick Disconnect, 5 meter cable RATED PRESSURE -100kPa = 29.9" Hg = 100% VACUUM SET POINT ATMOSPHERIC PRESSURE: 0 kpa = 0" Hg = 0% VACUUM Specifications Media Non lubricated air, Non-corrosive gas. Maximum Pressure 58 psi (400 kpa) Electrical Connection 4 pin pico 8 mm connector Operating Voltage 18 ~ 30 V DC polarity protection ± 10% Current Consumption <100 ma Display 2-digit, 7 segment Red LED Rated Display 0 ~ 99 Units Percent Vacuum (kpa) Output Display Output 1 - Red LED: Output 2 - Green LED Transistor Output 125 ma 24 V DC, Programable N.O. or N.C. Electromagnetic Comp. Industrial Standard, Class B Body Material Polyacetal Hysteresis Adjustable Protection IP 65 Programming Push Buttons Shock 10 G, XYZ 2012 EDCO USA. www.edcousa.net 6:9 ELECTRICAL CNECTI M8 Male 4-pin Connector 2 1 1. Brown Wire: Power Supply 2. White Wire: Output 2 3. Blue Wire: Common 4. Black Wire: Output 1 4 3
6 DIGITAL SENSORS HOW TO ORDER 1.22 [31] STYLE D V N 200 V = Vacuum P = Pressure 1.22 [31] OUTPUT N = NPN P = PNP 1.46 [37.1] 150mm CABLE WITH 8mm MALE 4-PIN CNECTOR 0.63 [16] 0.33 [8.4] 0.61 [15.5] SEPARATE OUTPUT MODE (HI OPERATI) (LO OPERATI) WINDOW COMPARATOR MODE (A OPERATI) (B OPERATI) ORDER CABLE SEPARATELY 0.61 [15.5] ELECTRICAL CNECTI M8 Male 4-pin Connector 2 4 1 3 PART NUMBER 4QD2 4QD5 DESCRIPTI 4-pin, Quick Disconnect, 2 meter cable 4-pin, Quick Disconnect, 5 meter cable 1. Brown Wire: Power Supply 2. White Wire: Output 2 3. Blue Wire: Common 4. Black Wire: Output 1 Optional Mounting Brackets Kit BT200-A SPECIFICATIS DV -200 DP -200 Media Non lubricated air, Non-corrosive gas, Incombustible gases. Maximum Pressure 29.5 psi (200 kpa) 200 psi (1379 kpa) Rated Pressure Range 0 ~ -29.5 inhg (0 ~ -100 kpa) 0 ~ 145 psi (1000 kpa) Operating Temperature 32 ~ 122 F (0 ~ 50 C) Storage Temperature -4 ~ 140 F (-20 ~ 60 C) Humidity 35 ~ 85% RH Electrical Connection 4 pin pico 8 mm connector Operating Voltage 12 ~ 24 V DC ± 10%, Ripple (P-P) 10% or less Current Consumption 55mA Display 3-digit, 7 segment Red LED Output Display OUT 1 - Green LED: OUT 2 - Red LED Display Cycle 5 Hz Repeatability ±0.2% F.S. ±1 digit (ambient temp. 25 ± 3 C) Hysteresis Hysteresis Mode: Adjustable, Window Comparator Mode: Fixed (3 digits) Switching Capacity 30 V DC, 80 ma max. Response Time 2.5 ms (chattering-proof function: 24 ms, 192 ms & 768 ms selections) Vibration Total amplitude 1.5 mm, 10Hz - 55Hz - 10Hz scan for 1 min, 2 hrs each XYZ Shock Insulation Resistance 980 m/s 2 (100G), 3 times each XYZ 50 MΩ minimum (at 500 V DC M, between case and lead wire) Dielectric Strength 1000 V AC in 1 min. (between case and lead wire) Thermal Error ± 2% F.S. of detected press. (25 C) at temp. Range of 0 ~ 50 C (32 ~ 122 F) kpa 0.1 MPa 01 kgf/cm 2 01 1 Set Pressure bar 01 1 Resolution psi 1 0.1 inhg 0.1 mmhg 1 mmh 2 O 0.1 6:10 2012 EDCO USA. www.edcousa.net
DIGITAL SENSORS HOW TO ORDER STYLE OUTPUT MOUNTING THREADS D V N 602 18M V = Vacuum N = NPN 5F = M5 x 0.8 (10-32 UNF) Female P = Pressure P = PNP 18M = Male 6-5F Option M5 x 0.8 (10-32 UNF) 0.49 [12.4] -18M Option 0.2 [5.1] 0.4 [10.2] 0.98 [24.9] 0.73 [18.5] 0.26 [6.6] 0.33 [8.4] 0.17 [4.3] 0.12 [3.0] Thru Hole 2 Places DISPLAY MODE: Press any button to activate the display for 10 seconds. Decimal point blinks in non-display mode. 2.07 [52.6] 2.24 [56.9] SEPARATE OUTPUT MODE (HI OPERATI) (LO OPERATI) WINDOW COMPARATOR MODE (A OPERATI) (B OPERATI) ORDER CABLE SEPARATELY Black White Brown Blue PART NUMBER JST1.5X4W DESCRIPTI 4-pin, Plug, 2 meter cable Specifications Media Non lubricated air, Non-corrosive gas. Maximum Pressure 29 psi (200 kpa) Rated Pressure Range -29.5 ~ 29.5 inhg (-100 ~ 100 kpa) Operating Temperature 14 ~ 122 F (-10 ~ 50 C) Storage Temperature -4 ~ 158 F (-20 ~ 70 C) Humidity 35 ~ 85% RH Electrical Connection 4 pin pico 8 mm connector Operating Voltage 10.8 ~ 26.4 V DC (including ripple) Current Consumption 30 ma maximum Display 3-digit, 7 segment Red LED Output Display P1 - Red LED: P2 - Red LED Display Cycle 4 Hz Resolution ±1 count Repeatability ±0.3% F.S. max. Hysteresis Adjustable, 0 ~ 30 counts Switching Capacity 30 V DC, 100 ma max. Response Time Adjustable, approx. 5, 25, or 250 ms Vibration 10 ~ 500 Hz 1.5 mm maximum, XYZ for 2 hrs Shock 490 m/s 2, XYZ for 2 times each in the power off condition. Insulation Resistance 100 MΩ minimum Dielectric Strength 500 V AC for 1 min. NPN Output Voltage 1.2 VDC max. PNP Output Voltage 2.2 V DC max. Thermal Error ±3% F.S. max. in range of 32 ~ 122 F (0 ~ 50 C) 2012 EDCO USA. www.edcousa.net 6:11 CODE PRESSURE DISPLAY RANGE UNITS 2-0.10 ~ 1.00 MPa 4-1.0 ~ 1 bar 5-14 ~ 145 psi MAXIMUM PRESSURE: 210 psi (1.5 MPa) CODE VACUUM DISPLAY RANGE UNITS 1-100 ~ 100 kpa 3-75 ~ 75 cmhg 4-1.00 ~ 1.00 bar 5-14.5 ~ 14.5 psi 6 29.5 ~ 0 inhg MAXIMUM PRESSURE: 58 psi (200 kpa)
6 OTHER ACCESSORIES 0.50 VACUUM SWITCH PROTECTORS [12.7] VSP-18 - Bi-directional VSP protects vacuum switches or gauges from positive pressure spikes by relieving pressure in excess of 10 psi (0.7 bar) to atmosphere. Connects to 1/8 NPTF or 1/8 BSPP threads. 0.60 [15.2] 0.33 [8.4] 0.24 [6.1] T-STYLE FILTERS Made of rugged nylon 6/6 body with transparent bowl for checking filter condition at a glance. HDPE filter element can be easily and quickly replaced without disturbing system plumbing. T-Style Filters are rated for full vacuum or pressure up to 150 psi. A A B D B D C C WITH MOLDED POLYETHYLENE ELEMENT FILTER A B C D WEIGHT ELEMENT PORTS NUMBER in. (mm) in. (mm) in. (mm) in. (mm) lb. (g) (3 PACK) PPSF125MX10 1/8 NPT M 3.06 (77.7) 2.42 (61.5) 1.86 (47.2) 1.98 (50.3) 0.13 (59) PPX10RE3 PPSF250MX10 1/4 NPT M 3.06 (77.7) 2.42 (61.5) 1.86 (47.2) 1.98 (50.3) 0.11 (49.9) PPX10RE3 PPSF375MX10 3/8 NPT M 3.06 (77.7) 2.42 (61.5) 1.86 (47.2) 1.98 (50.3) 0.16 (72.6) PPX10RE3 PPSF125X10 1/8 NPT F 3.06 (77.7) 2.42 (61.5) 1.86 (47.2) 1.98 (50.3) 0.13 (59) PPX10RE3 PPSF250X10 1/4 NPT F 3.06 (77.7) 2.42 (61.5) 1.86 (47.2) 1.98 (50.3) 0.11 (49.9) PPX10RE3 PPSF375X10 3/8 NPT F 3.06 (77.7) 2.42 (61.5) 1.86 (47.2) 1.98 (50.3) 0.16 (72.6) PPX10RE3 PPSF500X35 1/2 NPT F 3.64 (92.5) 5.35 (136) 2.95 (74.9) 4.8 (122) 0.37 (168) PPX35RE3 PPSF750X35 3/4 NPT F 3.64 (92.5) 5.35 (136) 2.95 (74.9) 4.8 (122) 0.4 (181) PPX35RE3 PPSF100X50 1 NPT F 4.62 (117) 6.36 (162) 4 (102) 5.6 (142) 0.94 (426) PPX50RE3 PPSF150X75 1-1/2 NPT F 5.16 (131) 8.1 (206) 4 (102) 6.93 (176) 1.18 (535) PPX75RE3 Some sizes are available in polypropylene. Call for availability. Add suffix - PP for polypropylene body and bowl. Bowl will be opaque, NOT transparent. For example: PPSF750X35-PP would be a 3/4 NPTF filter made of Black polypropylene. INLINE FILTER F10-18F The rugged F10-18F inline filter is designed to carry the full load of 50mm and smaller suction cups. The inline filter is ideal for use with Flow Sensor or Tri- Flow Valves in extremely dusty environments such as woodworking shops. The F10-18F provides more than 10 times the surface area of the standard FSV filter disk, providing a longer life. A Quick Release (blow-off) may be used to momentarily back flow the filters to help keep them clean. 1.74 [44.2] 1.0 [25.4] Anodized aluminum body, polyethylene element, and stainless steel fasteners. Replacement Filter Disk - FD-116 6:12 2012 EDCO USA. www.edcousa.net