TR & POWR ONTRO STON S OY ONTRO SYSTM ONTNTS PRUTON... 3 PRUTONS... 3 Precaution for Supplemental Restraint System (SRS) "R " and "ST T PR-TN- SONR"...3 SYSTM SRPTON... 4 OMPONNT PRTS... 4 OY ONTRO SYSTM...4 OY ONTRO SYSTM : omponent Parts ocation...4 POWR ONSUMPTON ONTRO SYSTM...4 POWR ONSUMPTON ONTRO SYSTM : omponent Parts ocation...4 SYSTM... 5 OY ONTRO SYSTM...5 OY ONTRO SYSTM : System...5 OMNTON SWT RN SYSTM...6 OMNTON SWT RN SYSTM : System iagram...6 OMNTON SWT RN SYSTM : System...6 SN UR SYSTM...9 SN UR SYSTM : System iagram...10 SN UR SYSTM : System...10 POWR ONSUMPTON ONTRO SYSTM...11 POWR ONSUMPTON ONTRO SYSTM : System iagram...11 POWR ONSUMPTON ONTRO SYSTM : System...11 NOSS SYSTM ()...13 OMMON TM...13 OMMON TM : ONSUT- unction ( - OMMON TM)...13 OOR O...14 OOR O : ONSUT- unction ( - OOR O)...14 RR WNOW OR...15 RR WNOW OR : ONSUT- unction ( - RR OR)...16 UZZR...16 UZZR : ONSUT- unction ( - UZZ- R)...16 NT MP...16 NT MP : ONSUT- unction ( - NT MP)...17 MP...18 MP : ONSUT- unction ( - MP)...18 WPR...21 WPR : ONSUT- unction ( - WPR)...21 SR...22 SR : ONSUT- unction ( - SR)...22 NTNT Y...23 NTNT Y : ONSUT- unction ( - NTNT Y)...23 OM SW...26 OM SW : ONSUT- unction ( - OM SW)...26...27 : ONSUT- unction ( - )...27 MMU...27 MMU : ONSUT- unction ( - MMU)...27 S N O P S-1
TTRY SVR... 28 TTRY SVR : ONSUT- unction ( - TTRY SVR)... 28 TRUN... 29 TRUN : ONSUT- unction ( - TRUN)... 29 TT M... 29 TT M : ONSUT- unction ( - TT)... 29 RTN PWR... 30 RTN PWR : ONSUT- unction ( - RTN PWR)... 30 SN UR... 30 SN UR : ONSUT- unction ( - SN UR)... 31 U NOSS NORMTON... 32... 32 Reference Value... 32 ail-safe... 52 T nspection Priority hart... 54 T ndex... 55 WRN RM... 58... 58 Wiring iagram... 58 S NSPTON... 65 NSPTON N USTMNT... 65 TON SRV WN RPN ONTRO UNT ()... 65 TON SRV WN RPN ONTRO UNT () :... 65 TON SRV WN RPN ONTRO UNT () : Special Repair Requirement... 65 ONURTON ()... 65 ONURTON () :... 65 ONURTON () : Special Repair Requirement... 66 ONURTON () : onfiguration list... 66 T/RUT NOSS... 68 U1000 N OMM... 68... 68 T ogic... 68 iagnosis Procedure... 68 U1010 ONTRO UNT (N)... 69 T ogic... 69 iagnosis Procedure... 69 U0415 V SP... 70... 70 T ogic... 70 iagnosis Procedure... 70 2562 OW VOT... 71 T ogic... 71 iagnosis Procedure... 71 267 TPMS N OMM... 72 T ogic... 72 iagnosis Procedure... 72 POWR SUPPY N ROUN RUT... 73 iagnosis Procedure... 73 OMNTON SWT OUTPUT RUT... 74 iagnosis Procedure... 74 OMNTON SWT NPUT RUT... 76 iagnosis Procedure... 76 SYMPTOM NOSS... 78 OMNTON SWT SYSTM SYMP- TOMS... 78 Symptom Table... 78 RMOV N NSTTON... 79... 79 Removal and nstallation... 79 OMNTON SWT... 80 xploded View... 80 Removal and nstallation... 80 S-2
< PRUTON > PRUTON PRUTONS PRUTONS Precaution for Supplemental Restraint System (SRS) "R " and "ST T PR-TNSONR" NO:0000000006059519 The Supplemental Restraint System such as R and ST T PR-TNSONR, used along with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted. nformation necessary to service the system safely is included in the SRS R and ST T of this Service Manual. WRNN: To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in the event of a collision that would result in air bag inflation, all maintenance must be performed by an authorized NSSN/NNT dealer. mproper maintenance, including incorrect removal and installation of the SRS, can lead to personal injury caused by unintentional activation of the system. or removal of Spiral able and ir ag Module, see the SRS R. o not use electrical test equipment on any circuit related to the SRS unless instructed to in this Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness connectors. PRUTONS WN USN POWR TOOS (R OR TR) N MMRS WRNN: When working near the ir ag iagnosis Sensor Unit or other ir ag System sensors with the ignition ON or engine running, O NOT use air or electric power tools or strike near the sensor(s) with a hammer. eavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing serious injury. When using air or electric power tools or hammers, always switch the ignition O, disconnect the battery, and wait at least 3 minutes before performing any service. S N O P S-3
< SYSTM SRPTON > SYSTM SRPTON OMPONNT PRTS OY ONTRO SYSTM OMPONNT PRTS OY ONTRO SYSTM : omponent Parts ocation NO:0000000006059520 MM0420ZZ 1.. ehind of instrument lower panel POWR ONSUMPTON ONTRO SYSTM POWR ONSUMPTON ONTRO SYSTM : omponent Parts ocation NO:0000000006059521 MM0421ZZ 1. ombination meter 2. PM /R Refer to PS-5, "PM /R : omponent Parts ocation". 4. Refer to S-4, "OY ONTRO SYSTM : omponent Parts ocation". 5. river seat control unit Refer to P-6, "omponent Parts ocation". 3. N gateway Refer to N-130, "omponent Parts ocation". 6. Pre-crash seat belt control unit (driver side) Refer to S-5, "omponent Parts ocation". S-4
< SYSTM SRPTON > SYSTM OY ONTRO SYSTM SYSTM OY ONTRO SYSTM : System NO:0000000006059522 OUTN (ody ontrol Module) controls the various electrical components. t inputs the information required to the control from N communication and the signal received from each switch and sensor. has combination switch reading function for reading the operation status of combination switches (light, turn signal, wiper and washer) in addition to a function for controlling the operation of various electrical components. t also has the signal transmission function as the passed point of signal and the power saving control function that reduces the power consumption with the ignition switch O. is equipped with the diagnosis function that performs the diagnosis with ONSUT- and various settings. ONTRO UNTON ST System ombination switch reading system Signal buffer system Power consumption control system uto light system Turn signal and hazard warning lamp system eadlamp system Parking, license plate, side maker and tail lamps system ront fog lamp system xterior lamp battery saver system aytime running light system nterior room lamp control system nterior room lamp battery saver system ront wiper and washer system utomatic air conditioner Warning chime system Power door lock system S-5 Reference S-6, "OMNTON SWT RN SYSTM : System iagram" S-10, "SN UR SYSTM : System iagram" S-11, "POWR ONSUMPTON ONTRO SYSTM : System iagram" X-13, "UTO T SYSTM (WTOUT TR) : System iagram" (Without daytime running light system) X-15, "UTO T SYSTM (WT TR) : System iagram" (With daytime running light system) X-20, "TURN SN N ZR WRNN MP SYS- TM : System iagram" X-11, "MP SYSTM (WTOUT TR) : System iagram" (Without daytime running light system) X-12, "MP SYSTM (WT TR) : System iagram" (With daytime running light system) X-20, "PRN, NS PT, S MRR N T MP SYSTM (WTOUT TR) : System iagram" (Without daytime running light system) X-21, "PRN, NS PT, S MRR N T MP SYSTM (WT TR) : System iagram" (With daytime running light system) X-19, "RONT O MP SYSTM : System iagram" X-23, "XTROR MP TTRY SVR SYSTM : System iagram" X-16, "YTM RUNNN T SYSTM : System iagram" N-7, "NTROR ROOM MP ONTRO SYSTM : System iagram" N-10, "NTROR ROOM MP TTRY SVR SYSTM : System iagram" WW-7, "RONT WPR N WSR SYSTM : System iagram" -19, "UTOMT R ONTONN SYSTM (WT ORST R) : System iagram" (With orest ir system) -26, "UTOMT R ONTONN SYSTM (WTOUT ORST R) : System iagram" (Without orest ir system) WS-6, "WRNN M SYSTM : System iagram" -12, "System iagram" S N O P
< SYSTM SRPTON > SYSTM System nfiniti Vehicle mmobilizer System (VS) - NTS Reference S-15, "NNT V MMOZR SYSTM-NTS : System iagram" Vehicle security system Rear window defogger system ntelligent ey system/engine start system Trunk lid opener system Power window system Theft warning alarm Panic alarm S-18, "V SURTY SYSTM : System iagram" -6, "System iagram" -14, "NTNT Y SYSTM : System iagram" -28, "System iagram" PW-7, "System iagram" Retained accessory power (RP) system OMNTON SWT RN SYSTM PW-7, "System " OMNTON SWT RN SYSTM : System iagram NO:0000000006059523 NOT: *: T MP switch links lighting switch 1ST and 2N positions. OMNTON SWT RN SYSTM : System MM0422 NO:0000000006059524 OUTN reads the status of the combination switch (light, turn signal, wiper and washer) and recognizes the status of each switch. has a combination of 5 output terminals (OUTPUT 1-5) and 5 input terminals (NPUT 1-5). t reads a maximum of 20 switch status. OMNTON SWT MTRX S-6
< SYSTM SRPTON > SYSTM ombination switch circuit NOT: *: T MP switch links lighting switch 1ST and 2N positions. ombination switch NPUT-OUTPUT system list System NPUT 1 NPUT 2 NPUT 3 NPUT 4 NPUT 5 NOT: eadlamp has a dual system switch. OMNTON SWT RN UNTON reads the status of the combination switch at 10 ms interval normally. MM0423 OUTPUT 1 R WSR R WPR OW TURN TURN R OUTPUT 2 R WPR R WPR UTO PSSN MP 1 OUTPUT 3 WP VOUM 1 MP 2 M OUTPUT 4 WP VOUM 3 UTO T T MP OUTPUT 5 WP VOUM 2 R O S N O PM0609 NOT: reads the status of the combination switch at 60 ms interval when is controlled at low power consumption control mode. operates as follows and judges the status of the combination switch. - t operates the transistor on OUTPUT side in the following order: OUTPUT 1 2 3 4 5, and outputs voltage waveform. P S-7
< SYSTM SRPTON > SYSTM - The voltage waveform of OUTPUT corresponding to the formed circuit is input into the interface on NPUT side if any (1 or more) switches are ON. - t reads this change of the voltage as the status signal of the combination switch. MM0326 Operation xample n the following operation example, the combination of the status signals of the combination switch is replaced as follows: NPUT 1-5 to 1-5 and OUTPUT 1-5 to -. xample 1: When a switch (T MP switch) is turned ON The circuit between OUTPUT 4 and NPUT 5 is formed when the T MP switch is turned ON. detects the combination switch status signal 5 when the signal of OUTPUT 4 is input to NPUT 5. judges that the T MP switch is ON when the signal 5 is detected. xample 2: When some switches (TURN R switch, T MP switch) are turned ON MM0424 S-8
< SYSTM SRPTON > SYSTM The circuits between OUTPUT 1 and NPUT 5 and between OUTPUT 4 and NPUT 5 are formed when the TURN R switch and T MP switch are turned ON. detects the combination switch status signal 5 when the signals of OUTPUT 1 and OUTPUT 4 are input to NPUT 5. judges that the TURN R switch and T MP switch are ON when the signal 5 is detected. WPR VOUM POSTON judges the wiper volume dial 1-7 by the status of WP VOUM 1, 2 and 3 switches. NOT: Wiper volume dial position Switch status MM0425 WP VOUM 1 WP VOUM 2 WP VOUM 3 1 ON ON ON 2 ON ON O 3 ON O O 4 O O O 5 O O ON 6 O ON ON 7 O ON O or details of wiper volume dial position, refer to WW-7, "RONT WPR N WSR SYSTM : System ". SN UR SYSTM S N O P S-9
< SYSTM SRPTON > SYSTM SN UR SYSTM : System iagram NO:0000000006059525 MM0426 SN UR SYSTM : System NO:0000000006059526 OUTN has the signal transmission function that outputs/transmits each input/received signal to each unit. Signal transmission function list Signal name nput gnition switch ON signal gnition switch signal oor switch signal Push-button ignition switch (Push switch) ny door switch PM /R (N) river seat control unit (N) Pre-crash seat belt control unit (N) ombination meter (N) PM /R (N) river seat control unit (N) Pre-crash seat belt control unit (N) Trunk switch signal Trunk room lamp switch ombination meter (N) Oil pressure switch signal PM /R (N) ombination meter (N) Stop lamp switch signal Stop lamp switch TM (N) ow tire pressure warning lamp signal ow tire pressure warning control unit (N) ombination meter (N) nputs the push-button ignition switch (push switch) signal and transmits the ignition switch status judged with via N communication. nputs the door switch signal and transmits it via N communication. nputs the trunk room lamp switch signal and transmits trunk switch signal via N communication. Transmits the received oil pressure switch signal via N communication. nputs the stop lamp switch 1 signal and stop lamp switch 2 signal, and transmits it via N communication. Transmits the received low tire pressure warning signal via N communication. S-10
< SYSTM SRPTON > SYSTM POWR ONSUMPTON ONTRO SYSTM POWR ONSUMPTON ONTRO SYSTM : System iagram NO:0000000006059527 POWR ONSUMPTON ONTRO SYSTM : System MM0427 NO:0000000006059528 OUTN incorporates a power saving control function that reduces the power consumption according to the vehicle status. switches the status (control mode) by itself with the power saving control function. t performs the sleep request to each unit (PM /R, combination meter, driver seat control unit, pre-crash seat belt control unit and N gateway) that operates with the ignition switch O. Normal mode (wake-up) - N communication is normally performed with other units - ach control with is operating properly N communication sleep mode (N sleep) - N transmission is stopped - ontrol with only is operating ow power consumption mode ( sleep) - ow power consumption control is active - N transmission is stopped OW POWR ONSUMPTON ONTRO WT reduces the power consumption with the following operation in the low power consumption mode. The reading interval of the each switches changes from 10 ms interval to 60 ms interval. Sleep mode activation receives the sleep-ready signal (ready) from PM /R and combination meter via N communication. transmits the sleep wake up signal (sleep) to each unit when all of the N sleep conditions are fulfilled. ach unit stops the transmission of N communication with the sleep wake up signal. is in N communication sleep mode. is in the low power consumption mode and perform the low power consumption control when all of the sleep conditions are fulfilled with N sleep condition. S N O P S-11
< SYSTM SRPTON > Sleep condition N sleep condition Receiving the sleep-ready signal (ready) from all units gnition switch: O Vehicle security system and panic alarm: Not operation Warning chime: Not operation ntelligent ey system buzzer: Not operation Trunk room lamp switch status: No change Stop lamp switch: O brake hold relay (with ): O Turn signal indicator lamp: Not operation xterior lamp: O oor lock status: No change ONSUT- communication status: Not communication Meter display signal: Non-transmission oor switch status: No change Rear window defogger: O river door lock status: No change SYSTM sleep condition nterior room lamp battery saver: Time out RP system: O nfiniti Vehicle mmobilizer System (VS) - NTS: Not operation Remote keyless entry receiver communication status: No communication O indicator lamp: Not operation indicator lamp: Not operation ON indicator lamp: Not operation Wake-up operation transmits sleep wake up signal (wake up) to each unit when any condition listed below is established, and then goes into normal mode from low power consumption mode. ach unit starts transmissions with N communication by receiving sleep wake up signals. ach unit transmit wake up signals to with N communication to convey the start of N communication. Wake-up condition Receiving the sleep-ready signal (Not-ready) from any units Push-button ignition switch (push switch): O ON azard switch: ON M switch: O ON, ON O PSSN switch: O ON, ON O MP 1 switch: O ON, ON O MP 2 switch: O ON, ON O T MP switch: O ON R O switch: O ON, ON O TURN R: O ON, ON O TURN : O ON, ON O river door switch: O ON, ON O Passenger door switch: O ON, ON O Rear R door switch: O ON, ON O Rear door switch: O ON, ON O Trunk room lamp switch: O ON, ON O river door request switch: O ON Passenger door request switch: O ON Trunk lid opener request switch: O ON Trunk lid opener switch: O ON Stop lamp switch: ON brake hold relay (with ): ON Remote keyless entry receiver communication: Receiving ront door lock assembly (driver side) (unlock sensor): O ON, ON O Wake-up condition S-12
< SYSTM SRPTON > NOSS SYSTM () OMMON TM NOSS SYSTM () OMMON TM : ONSUT- unction ( - OMMON TM) PPTON TM ONSUT- performs the following functions via N communication with. iagnosis mode Work Support Self iagnostic Result N iag Support Monitor ata Monitor ctive Test cu dentification onfiguration SYSTM PPTON can perform the following functions for each system. NOT: t can perform the diagnosis modes except the following for all sub system selection items. System *: This item is not used. unction NO:0000000006059529 hanges the setting for each system function. isplays the diagnosis results judged by. Monitors the reception status of N communication viewed from. Refer to ONSUT- operation manual. The input/output signals are displayed. The signals used to activate each device are forcibly supplied from. The part number is displayed. Read and save the vehicle specification. Write the vehicle specification when replacing. Sub system selection item iagnosis mode : pplicable item Work Support ata Monitor ctive Test oor lock OOR O Rear window defogger RR OR Warning chime UZZR nterior room lamp timer NT MP xterior lamp MP Wiper and washer WPR Turn signal and hazard warning lamps SR ntelligent ey system ngine start system R ONTONR* NTNT Y ombination switch OM SW ody control system VS - NTS MMU nterior room lamp battery saver TTRY SVR Trunk lid open TRUN Vehicle security system TT M RP system RTN PWR Signal buffer system SN UR RZ RM T () The records the following vehicle condition at the time a particular T is detected, and displays on ONSUT-. S N O P S-13
< SYSTM SRPTON > NOSS SYSTM () ONSUT screen item ndication/unit Vehicle Speed km/h Vehicle speed of the moment a particular T is detected Odo/Trip Meter km Total mileage (Odometer value) of the moment a particular T is detected Vehicle ondition OOR O OOR O : ONSUT- unction ( - OOR O) ONSUT- UNTON ONSUT- performs the following functions via N communication with. WOR SUPPORT SP>O SP>O O> >ON RUN> RN>RUN RUN>URNT >O O>O O> ON>RN O>SP O>SP O O ON N ounter 0-39 NN RUN RNN Power position status of the moment a particular T is detected While turning status from low power consumption mode to normal mode (Power supply position is O ) While turning status from low power consumption mode to normal mode (Power supply position is O.) While turning power supply position from O to While turning power supply position from to N While turning power supply position from RUN to (Vehicle is stopping and selector lever is except P position.) While turning power supply position from RNN to RUN (rom cranking up the engine to run it) While turning power supply position from RUN to (mergency stop operation) While turning power supply position from to O While turning power supply position from O to O While turning power supply position from O to While turning power supply position from N to RNN While turning status from normal mode (Power supply position is O.) to low power consumption mode While turning status from normal mode (Power supply position is O.) to low power consumption mode Power supply position is O (gnition switch O with steering is locked.) Power supply position is O (gnition switch O with steering is unlocked.) Power supply position is (gnition switch ) Power supply position is N (gnition switch ON with engine stopped) Power supply position is RUN (gnition switch ON with engine running) Power supply position is RNN (t engine cranking) The number of times that ignition switch is turned ON after T is detected The number is 0 when a malfunction is detected now. The number increases like 1 2 3...38 39 after returning to the normal condition whenever ignition switch O ON. The number is fixed to 39 until the self-diagnosis results are erased if it is over 39. NO:0000000006134053 S-14
< SYSTM SRPTON > NOSS SYSTM () Monitor item OOR O-UNO ST UTOMT OOR O S- T UTOMT OOR UNO ST UTOMT O/UNO ST T MONTOR Selective unlock function mode can be changed to operation with this mode : Operate : Non-operation utomatic door lock function mode can be selected from the following in this mode V SP: ll doors are locked when vehicle speed more than 24 km/h (15MP) P RN: ll doors are locked when shifting the selector lever from P position to other than the P position utomatic door unlock function mode can be selected from the following in the mode MO 1: ll doors are unlocked when the power supply position is changed from ON to O MO 2: ll doors are unlocked when shifting the selector lever from any position other than the P to P position MO 3: river side door is unlocked when the power supply position is changed from ON to O MO 4: river side door is unlocked when shifting the selector lever from any position other than the P to P position MO 5: This item is displayed, but cannot be used MO 6: This item is displayed, but cannot be used utomatic door lock/unlock function mode can be selected from the following in this mode : Non-operational Unlock ly: oor unlock operation only ock ly: oor lock operation only ock/unlock: ock and unlock operation Monitor tem RQ SW-R RQ SW-S RQ SW-/TR OOR SW-R OOR SW-S OOR SW-RR OOR SW-R OOR SW- O SW UNO SW Y Y -SW Y Y UN-SW TV TST ontents ndicated [/] condition of door request switch (driver side) ndicated [/] condition of door request switch (passenger side) ndicated [/] condition of trunk lid opener request switch ndicated [/] condition of front door switch (driver side) ndicated [/] condition of front door switch (passenger side) ndicated [/] condition of rear door switch R ndicated [/] condition of rear door switch NOT: This item is displayed, but cannot be monitored ndicated [/] condition of lock signal from door lock unlock switch ndicated [/] condition of unlock signal from door lock unlock switch ndicated [/] condition of lock signal from door key cylinder switch ndicated [/] condition of unlock signal from door key cylinder switch S N OOR O Test item RR WNOW OR This test is able to check door lock/unlock operation The all door lock actuators are locked when O on ONSUT- screen is touched The all door lock actuators are unlocked when UN on ONSUT- screen is touched The front door lock actuator (driver side) is unlocked when R UN on ONSUT- screen is touched The front door lock actuator (passenger side) is unlocked when S UN on ONSUT- screen is touched The door lock actuator (other) is unlocked when OTR U on ONSUT- screen is touched O P S-15
< SYSTM SRPTON > NOSS SYSTM () RR WNOW OR : ONSUT- unction ( - RR OR) ata monitor NO:0000000006134059 Monitor tem RR SW PUS SW This is displayed even when it is not equipped. ndicates [ON/O] condition of push switch. TV TST UZZR Test tem RR OR UZZR : ONSUT- unction ( - UZZR) ONSUT- PPTON TMS This test is able to check rear window defogger operation. Rear window defogger operates when ON on ONSUT- screen is touched. NO:0000000006134065 Test item iagnosis mode ata Monitor isplays input data in real time. UZZR ctive Test Operation of electrical loads can be checked by sending driving signal to them. T MONTOR isplay item [Unit] PUS SW [/] UN SN-R [/] V SP 1 [km/h] T MP SW [/] R O SW [/] OOR SW-R [/] O SW [/] Status of push-button ignition switch judged by. Status of unlock sensor judged by. Value of vehicle speed signal received from combination meter with N communication line. Status of lighting switch judged by using the combination switch readout function. Status of front fog lamp switch judged by using the combination switch readout function. Status of driver side door switch judged by. Status of door lock unlock switch judged by. TV TST isplay item [Unit] ST T WRN TST T WRN M NT MP The seat belt warning chime operation can be checked by operating the relevant function (/). The light warning chime operation can be checked by operating the relevant function (/). S-16
< SYSTM SRPTON > NOSS SYSTM () NT MP : ONSUT- unction ( - NT MP) WOR SUPPORT NO:0000000006134060 M0961 ST / -UN NTON ROOM MP TMR ST ROOM MP ON TM ST ROOM MP O TM ST R MP TMR O ST *: actory setting T MONTOR Service item Setting item Setting * With the interior room lamp timer function Without the interior room lamp timer function MO 2 7.5 sec. MO 3* 15 sec. Sets the interior room lamp ON time. (Timer operating time) MO 4 30 sec. MO 1 0.5 sec. MO 2 1 sec. MO 3 2 sec. Sets the interior room lamp gradual brightening time. MO 4 3 sec. MO 5 0 sec. MO 6* radually brightens from 0% to 100% brightness in 1 second. MO 1 0.5 sec. MO 2 1 sec. MO 3 2 sec. Sets the interior room lamp gradual dimming time. MO 4 3 sec. MO 5 0 sec. MO 6* radually dims from 100% to 0% in 1 second. MO 1* nterior room lamp timer activates with synchronizing all doors. MO 2 nterior room lamp timer activates with synchronizing the driver door only. S N O RQ SW-R [/] Monitor item [Unit] The switch status input from request switch (driver side) P RQ SW-S [/] The switch status input from request switch (passenger side) S-17
< SYSTM SRPTON > RQ SW-RR [/] RQ SW-R [/] PUS SW [/] UN SN -R [/] OOR SW-R [/] OOR SW-S [/] OOR SW-RR [/] OOR SW- R [/] OOR SW- [/] O SW [/] UNO SW [/] Y Y -SW [/] Y Y UN-SW [/] TRN/T MNTR [/] R-O [/] R-UNO [/] Monitor item [Unit] NOSS SYSTM () NOT: The item is indicated, but not monitored. Push switch status received from ntelligent ey unit via N communication river door unlock status input from unlock sensor The switch status input from front door switch (driver side) The switch status input from front door switch (passenger side) The switch status input from rear door switch R The switch status input from rear door switch NOT: The item is indicated, but not monitored. ock switch status input from door lock and unlock switch Unlock switch status input from door lock and unlock switch ock switch status received from key cylinder lock/unlock switch Unlock switch status received from key cylinder lock/unlock switch The switch status input from trunk room lamp switch ock signal status received from remote keyless entry receiver Unlock signal status received from remote keyless entry receiver TV TST NT MP MP MP : ONSUT- unction ( - MP) WOR SUPPORT Test item Operation STP MP TST s the interior room lamp control signal to turn the interior room lamps ON. [Map lamp, personal lamp, foot lamp (when applicable lamps switch is in OOR position.)] Stops the interior room lamp control signal to turn the interior room lamps O. s the step lamp control signal to turn the step lamps ON. Stops the step lamp control signal to turn the step lamps ON. NO:0000000006134062 S-18
< SYSTM SRPTON > NOSS SYSTM () Service item Setting item Setting USTOM /T STTN UTO T O ST * MO 1 * MO 2 Normal More sensitive setting than normal setting (Turns ON earlier than normal operation.) MO 3 More sensitive setting than MO 2 (Turns ON earlier than MO 2.) MO 4 ess sensitive setting than normal setting (Turns ON later than normal operation.) MO 1 * MO 2 MO 3 MO 4 MO 5 MO 6 With twilight ON custom & with wiper NT, O and With twilight ON custom & with wiper O and With twilight ON custom & without Without twilight ON custom & with wiper NT, O and Without twilight ON custom & with wiper O and Without twilight ON custom & without TTRY SVR ST * With the exterior lamp battery saver function Without the exterior lamp battery saver function MO 1 * 45 sec. Y ST *: actory setting *: or models with daytime running light system, this item is not displayed. T MONTOR PUS SW [/] Monitor item [Unit] NN STT [Stop/Stall/rank/Run] V SP 1 [km/h] MO 2 MO 3 MO 4 MO 5 MO 6 MO 7 MO 8 Without the function 30 sec. 60 sec. 90 sec. 120 sec. 150 sec. 180 sec. Sets delay timer function timer operation time. (ll doors closed) The switch status input from push-button ignition switch The engine status received from M via N communication The value of the vehicle speed received from combination meter via N communication S N O P S-19
< SYSTM SRPTON > TURN SN R [/] TURN SN [/] T MP SW [/] M SW [/] MP SW1 [/] MP SW2 [/] PSSN SW [/] UTO T SW [/] R O SW [/] RR O SW [/] OOR SW-R [/] OOR SW-S [/] OOR SW-RR [/] OOR SW- R [/] OOR SW- [/] OPT SNSOR [/] Monitor item [Unit] OPT SN (TT) [V] OPT SN (T) [V] NOSS SYSTM () ach switch status that judges from the combination switch reading function NOT: The item is indicated, but not monitored. The switch status input from front door switch (driver side) The switch status input from front door switch (passenger side) The switch status input from rear door switch R The switch status input from rear door switch NOT: The item is indicated, but not monitored. The sensor status input from optical sensor The value of outside brightness voltage input from the optical sensor The sensor outside brightness voltage filtered by. TV TST T MP MP R O MP Test item Operation i ow Transmits the position light request signal to PM /R via N communication to turn the tail lamp ON. Stops the tail lamp request signal transmission. Transmits the high beam request signal via N communication to turn the headlamp (). Transmits the low beam request signal via N communication to turn the headlamp (O). Stops the high & low beam request signal transmission. Transmits the front fog lights request signal to PM /R via N communication to turn the front fog lamp ON. Stops the front fog lights request signal transmission. S-20
< SYSTM SRPTON > NOSS SYSTM () RR O MP YTM RUNNN T* M SN *: or models without daytime running light system, This item is displayed but active test is not operated. WPR WPR : ONSUT- unction ( - WPR) WOR SUPPORT Test item Operation NOT: The item is indicated, but cannot be tested. Transmits the daytime running light request signal via N communication to turn the headlamp (O), parking, license plate, side marker and tail lamps ON. Stop the daytime running light request signal transmission. Transmits the dimmer signal to combination meter via N communication and dims combination meter. Transmits the dimmer signal to V control unit and dims display. Stops the dimmer signal transmission. NO:0000000006134064 Service item Setting item RN SN WP UN ST ROP WP UN ST *: actory setting T MONTOR * MO1 MO2* MO3 MO4 With rain sensor (ront wiper intermittent time linked with the rain sensor, vehicle speed, and UTO dial position) Without rain sensor (ront wiper intermittent time linked with the vehicle speed and UTO dial position) ront wiper drop wipe O ront wiper drop wipe ON The same setting as MO1 The same setting as MO2 The setting of front wiper UTO operation can be changed The setting of drop wipe operation can be changed Monitor tem [Unit] PUS SW [/] V SP 1 [km/h] R WPR [/] R WPR OW [/] R WSR SW [/] R WPR NT [/] R WPR STOP [/] NT VOUM [1 7] The switch status input from push-button ignition switch. isplays the value of the vehicle speed signal received from combination meter via N communication. Status of each switch judged by using the combination switch reading function isplays the status of the front wiper position signal received from PM /R via N communication. Status of each switch judged by using the combination switch reading function S N O P S-21
< SYSTM SRPTON > / WS SW [/] Monitor tem [Unit] RN SNSOR [O/OW//SPS/N] NOSS SYSTM () NOT: This item is indicated, but not monitored Request signal from rain sensor detected by is displayed TV TST R WPR SR Test item Operation SR : ONSUT- unction ( - SR) WOR SUPPORT i o NT Transmits the front wiper request signal () to PM /R via N communication to operate the front wiper operation. Transmits the front wiper request signal (O) to PM /R via N communication to operate the front wiper O operation. Transmits the front wiper request signal (NT) to PM /R via N communication to operate the front wiper NT operation. Stops transmitting the front wiper request signal to stop the front wiper operation. NO:0000000006134063 *: actory setting Service item Setting item Setting ZR NSWR T MONTOR ock ly Unlock ly ock&unlock * With locking only With unlocking only With locking/unlocking Without the function Sets the hazard warning lamp answer back function when the door is lock/unlock with the request switch or the key fob. RQ SW-R [/] RQ SW-S [/] PUS SW [/] TURN SN R [/] TURN SN [/] ZR SW [/] R-O [/] R-UNO [/] R-PN [/] Monitor item [Unit] The switch status input from the request switch (driver side) The switch status input from the request switch (passenger side) The switch status input from the push-button ignition switch ach switch status that detects from the combination switch reading function The switch status input from the hazard switch ock signal status received from the remote keyless entry receiver Unlock signal status received from the remote keyless entry receiver Panic alarm signal status received from the remote keyless entry receiver TV TST S-22
< SYSTM SRPTON > NOSS SYSTM () Test item Operation R s the voltage to blink the right side turn signal lamps. SR s the voltage to blink the left side turn signal lamps. Stops the voltage to turn the turn signal lamps O. NTNT Y NTNT Y : ONSUT- unction ( - NTNT Y) WOR SUPPORT NO:0000000006134054 Monitor item NS NT NOSS O/UNO Y -Y NN STRT Y -Y TRUN/SS T OPN PN RM ST TRUN OPN Y O- TT O Y O WRN NT Y O N UNT ZR NSWR NS -Y O NS -Y UNO SORT RNN OUTPUT This function allows inside key antenna self-diagnosis oor lock/unlock function by door request switch mode can be changed to operation in this mode : Operate : Non-operation ngine start function mode can be changed to operation with this mode : Operate : Non-operation uzzer reminder function mode by trunk lid opener request switch and ntelligent ey can be changed to operation with this mode : Operate : Non-operation Panic alarm button pressing time on ntelligent ey remote control button can be selected from the following with this mode MO 1: 0.5 sec MO 2: Non-operation MO 3: 1.5 sec Trunk button pressing on ntelligent ey can be selected as per the following in this mode. MO 1: Press and hold MO 2: Press twice MO 3: Press and hold, or press twice ntelligent ey low battery warning mode can be changed to operation with this mode : Operate : Non-operation ey reminder function mode can be changed to operation with this mode : Operate : Non-operation azard reminder function mode by door request switch and ntelligent ey button can be selected from the following with this mode ock ly: oor lock operation only Unlock ly: oor unlock operation only ock/unlock: ock and unlock operation : Non-operation uzzer reminder function (lock operation) mode by door request switch can be selected from the following with this mode orn hirp: Sound horn uzzer: Sound ntelligent ey warning buzzer : Non-operation uzzer reminder function (unlock operation) mode by door request switch can be changed to operation with this mode : Operate : Non-operation Starter motor can operate during the times below 70 msec 100 msec 200 msec S N O P S-23
< SYSTM SRPTON > Monitor item ONRM Y O UTO O ST ORN WT YSS O PW OWN ST WOM T ST WOM T OP ST NTNT Y STUP NOSS SYSTM () t can be checked whether ntelligent ey code is registered or not in this mode uto door lock operation time can be changed in this mode MO 1: O MO 2: 30 sec MO 3: 1 minute MO 4: 2 minutes MO 5: 3 minutes MO 6: 4 minutes MO 7: 5 minutes orn reminder function mode by ntelligent ey button can be selected from the following with this mode : Operate : Non-operation Unlock button pressing time on ntelligent ey button can be selected from the following with this mode MO 1: 3 sec MO 2: Non-operation MO 3: 5 sec Welcome light function mode can be selected from the following with this mode Puddle/Outside andle Room lamp ead & Tail amps (this item is displayed, but cannot be used) eart eat Welcome light function mode can be changed to operation with this mode : Operate : Non-operation ntelligent ey interlock function mode can be changed to operation with this mode : Operate : Non-operation S- RSUT Refer to S-55, "T ndex". T MONTOR Monitor tem RQ SW -R RQ SW -S RQ SW -/TR PUS SW UT SW S-24 ondition ndicates [/] condition of door request switch (driver side) ndicates [/] condition of door request switch (passenger side) ndicates [/] condition of trunk lid opener request switch ndicates [/] condition of push-button ignition switch NOT: This item is displayed, but cannot be monitored R SW 1 ndicates [/]* condition of stop lamp switch power supply R SW 2 ndicates [/] condition of stop lamp switch T/N SW ndicates [/] condition of P position ST PN/N SW ndicates [/] condition of P or N position S/ -O ndicates [/] condition of steering lock unit (O) S/ -UNO ndicates [/] condition of steering lock unit (UNO) S/ RY -/ ndicates [/] condition of steering lock relay UN SN -R ndicates [/] condition of driver door UNO status PUS SW -PM ndicates [/] condition of push-button ignition switch N RY1 -/ ndicates [/] condition of ignition relay 1 T SW -PM ndicates [/] condition of P position ST PN -PM ndicates [/] condition of P or N position
< SYSTM SRPTON > NOSS SYSTM () ST P -MT ST N -MT NN STT S/ O-PM S/ UN-PM S/ RY-RQ V SP 1 V SP 2 OOR STT-R OOR STT-S O PRMT N STRT PRMT R STRT TRN/T MNTR R-O R-UNO R-TR/ R-PN R-MO *: O is displayed when brake pedal is depressed while brake switch power supply is O. TV TST Monitor tem R OP OUN1 R OP OUN2 Test item TTRY SVR OUTS UZZR NS UZZR NTOR NT MP ondition ndicates [/] condition of P position ndicates [/] condition of N position ndicates [Stop/Stall/rank/Run] condition of engine states ndicates [/] condition of steering lock unit (O) ndicates [/] condition of steering lock unit (UNO) ndicates [/] condition of steering lock relay isplay the vehicle speed signal received from combination meter by numerical value [m/h] isplay the vehicle speed signal received from S or V or TM by numerical value [m/h] ndicates [O/RY/UN] condition of driver side door status ndicates [O/RY/UN] condition of passenger side door status ndicates [Set/Reset] condition of key ndicates [Set/Reset] condition of engine start possibility NOT: This item is displayed, but cannot be monitored ndicates [/] condition of trunk room lamp switch ndicates [/] condition of O signal from ntelligent ey ndicates [/] condition of UNO signal from ntelligent ey ndicates [/] condition of trunk open signal from ntelligent ey ndicates [/] condition of panic alarm button of ntelligent ey ndicates [/] condition of MO N signal from ntelligent ey When remote keyless entry receiver receives the signal transmitted while operating on ntelligent ey, the numerical value start changing NOT: This item is displayed, but cannot be monitored This test is able to check interior room lamp operation : Operate : Non-operation This test is able to check ntelligent ey warning buzzer operation : Operate : Non-operation This test is able to check warning chime in combination meter operation Take Out: Take away warning chime sounds when ONSUT- screen is touched ey: ey warning chime sounds when ONSUT- screen is touched nob: O position warning chime sounds when ONSUT- screen is touched : Non-operation This test is able to check warning lamp operation Y ON: Y Warning lamp illuminates when ONSUT- screen is touched Y N: Y Warning lamp blinks when ONSUT- screen is touched : Non-operation This test is able to check interior room lamp operation : Operate : Non-operation S N O P S-25
< SYSTM SRPTON > NOSS SYSTM () SR P RN NN SW UM O NTOR NTOR NTON ON N ORN OM SW Test item TRUN/ OOR NTNT Y N NTNT Y N (N) OM SW : ONSUT- unction ( - OM SW) T MONTOR This test is able to check meter display information ngine start information displays when P N on ONSUT- screen is touched ngine start information displays when P on ONSUT- screen is touched ey warning displays when N on ONSUT- screen is touched Steering lock information displays when ROTT on ONSUT- screen is touched P position warning displays when ST P on ONSUT- screen is touched NSRT: This item is displayed, but cannot be monitored TT: This item is displayed, but cannot be monitored Take away through window warning displays when NO Y on ONSUT- screen is touched Take away warning display when OUTY on ONSUT- screen is touched O position warning display when WN on ONSUT- screen is touched This test is able to check hazard warning lamp operation The hazard warning lamps are activated after /R/ on ONSUT- screen is touched This test is able to check T shift selector power supply : Operate : Non-operation This test is able to check push-ignition switch illumination operation Push-ignition switch illumination illuminates when ON on ONSUT- screen is touched This test is able to check O indicator (push-button ignition switch) operation : Operate : Non-operation This test is able to check indicator (push-button ignition switch) operation : Operate : Non-operation This test is able to check ON indicator (push-button ignition switch) operation : Operate : Non-operation This test is able to check horn operation : Operate : Non-operation This test is able to check trunk lid open operation Open: Operate This test is able to check ntelligent ey interlock function No1: transmits ntelligent ey No1 to each control unit No2: transmits ntelligent ey No2 to each control unit This test is able to check ntelligent ey interlock function : Non-operation No1: transmits ntelligent ey No1 to each control unit via N communication line No2: transmits ntelligent ey No2 to each control unit via N communication line No3: transmits ntelligent ey No3 to each control unit via N communication line No4: transmits ntelligent ey No4 to each control unit via N communication line No5: This item is displayed, but cannot be used NO:0000000006059530 Monitor item [UNT] R WPR [/] R WPR OW [/] S-26 isplays the status of the R WPR switch in combination switch judged by with the combination switch reading function. isplays the status of the R WPR OW switch in combination switch judged by with the combination switch reading function.
< SYSTM SRPTON > NOSS SYSTM () Monitor item [UNT] R WSR SW [/] R WPR NT [/] NT VOUM [1-7] TURN SN R [/] TURN SN [/] T MP SW [/] M SW [/] MP SW 1 [/] MP SW 2 [/] PSSN SW [/] isplays the status of the R WSR switch in combination switch judged by with the combination switch reading function. isplays the status of the R WPR UTO switch in combination switch judged by with the combination switch reading function. isplays the status of wiper volume dial position judged by with the combination switch reading function. isplays the status of the TURN R switch in combination switch judged by with the combination switch reading function. isplays the status of the TURN switch in combination switch judged by with the combination switch reading function. isplays the status of the T MP switch in combination switch judged by with the combination switch reading function. isplays the status of the M switch in combination switch judged by with the combination switch reading function. isplays the status of the MP 1 switch in combination switch judged by with the combination switch reading function. isplays the status of the MP 2 switch in combination switch judged by with the combination switch reading function. isplays the status of the PSSN switch in combination switch judged by with the combination switch reading function. UTO T SW [/] R O SW [/] RR O SW [/] : ONSUT- unction ( - ) WOR SUPPORT isplays the status of the UTO T switch in combination switch judged by with the combination switch reading function. isplays the status of the R O switch in combination switch judged by with the combination switch reading function. NOT: The item is indicated, but not monitored. NO:0000000006059531 MMU tem RST STTN VU Return a value set with Work Support of each system to a default value in factory shipment. MMU : ONSUT- unction ( - MMU) NO:0000000006134057 S T MONTOR Monitor item ONRM ONRM 4 ONRM 3 ONRM 2 ONRM 1 TP 4 TP 3 TP 2 TP 1 ontent ndicates [YT] at all time. Switches to [ON] when a registered ntelligent ey backside is contacted to push-button ignition switch. ndicates the number of s that are registered. N O P S-27
< SYSTM SRPTON > NOSS SYSTM () PUS SW Y SW-SOT Monitor item ontent ndicates [ON/O] condition of push-button ignition switch. NOT: This is displayed even when it is not equipped. TV TST TT N Test item This test is able to check security indicator lamp operation. Security indicator lamp is turned on when ON on ONSUT- screen touched. WOR SUPPORT Service item ONRM ON t is possible to check that dongle unit is applied to the vehicle. TTRY SVR TTRY SVR : ONSUT- unction ( - TTRY SVR) NO:0000000006134061 WOR SUPPORT Service item Setting item Setting ROOM MP TMR ST TTRY SVR ST *:actory setting T MONTOR MO 1 * 30 min. Sets the interior room lamp battery saver timer operating MO 2 60 min. time. * With the exterior lamp battery saver function Without the exterior lamp battery saver function RQ SW-R [/] RQ SW-S [/] RQ SW-RR [/] RQ SW-R [/] PUS SW [/] UN SN-R [/] OOR SW-R [/] OOR SW-S [/] OOR SW-RR [/] OOR SW- R [/] OOR SW- [/] Monitor item [Unit] S-28 The switch status input from request switch (driver side) The switch status input from front request switch (passenger side) NOT: The item is indicated, but not monitored. Push switch status received from ntelligent ey unit by N communication river door unlock status input from unlock sensor The switch status input from front door switch (driver side) The switch status input from front door switch (passenger side) The switch status input from rear door switch R The switch status input from rear door switch NOT: The item is indicated, but not monitored.
< SYSTM SRPTON > O SW [/] UNO SW [/] Y Y -SW [/] Y Y UN-SW [/] TRN/T MNTR [/] R-O [/] R-UNO [/] TV TST Monitor item [Unit] NOSS SYSTM () ock switch status input from door lock and unlock switch Unlock switch status input from door lock and unlock switch ock switch status received from key cylinder lock/unlock switch Unlock switch status received from key cylinder lock/unlock switch The switch status input from trunk room lamp switch ock signal status received from remote keyless entry receiver Unlock signal status received from remote keyless entry receiver Test item Operation TTRY SVR *: ach lamp switch is in ON position. TRUN uts the interior room lamp power supply to turn interior room lamps O. s the interior room lamp power supply to turn interior room lamps ON.* TRUN : ONSUT- unction ( - TRUN) T MONTOR NO:0000000006134055 Monitor tem PUS SW UN SN -R V SP 1 Y Y SW-TR TR N SW TR/ OPN SW ontents ndicates [/] condition of push switch ndicates [/] condition of unlock sensor ndicates [m/h] condition of vehicle speed signal from combination meter ndicates [/] condition of trunk key cylinder switch ndicates [/] condition of trunk lid opener cancel switch ndicates [m/h] condition of trunk lid opener switch TRN/T MNTR ndicates [/] condition of trunk room lamp switch R-TR/ ndicates [/] condition of trunk open signal from ntelligent ey TT M TT M : ONSUT- unction ( - TT) T MONTOR NO:0000000006134056 S N O Monitored tem RQ SW -R RQ SW -S RQ SW -RR RQ SW -R RQ SW -/TR ndicates [ON/O] condition of door request switch (driver side). ndicates [ON/O] condition of door request switch (passenger side). NOT: This is displayed even when it is not equipped. NOT: This is displayed even when it is not equipped. ndicates [ON/O] condition of trunk lid opener request switch. P S-29
< SYSTM SRPTON > Monitored tem NOSS SYSTM () PUS SW UN SN -R OOR SW-R OOR SW-S OOR SW-RR OOR SW-R OOR SW- O SW UNO SW Y Y -SW Y Y UN-SW Y Y SW-TR TR/ OPN SW TRN/T MNTR R-O R-UNO R-TR/ ndicates [ON/O] condition of push-button ignition switch ndicates [ON/O] condition of driver door UNO status. ndicates [ON/O] condition of front door switch (driver side). ndicates [ON/O] condition of front door switch (passenger side). ndicates [ON/O] condition of rear door switch R. ndicates [ON/O] condition of rear door switch. NOT: This is displayed even when it is not equipped. ndicates [ON/O] condition of lock signal from door lock and unlock switch. ndicates [ON/O] condition of unlock signal from door lock and unlock switch. ndicates [ON/O] condition of lock signal from door key cylinder switch. ndicates [ON/O] condition of unlock signal from door key cylinder switch. ndicates [ON/O] condition of trunk lid open signal from trunk key cylinder switch. ndicates [ON/O] condition of trunk lid opener switch. ndicates [ON/O] condition of trunk loom lamp switch. ndicates [ON/O] condition of O signal from ntelligent ey. ndicates [ON/O] condition of UNO signal from ntelligent ey. ndicates [ON/O] condition of TRUN OPN signal from ntelligent ey. WOR SUPPORT Test tem SURTY RM ST TT M TR This mode is able to confirm and change vehicle security system (theft warning alarm) ON-O setting. The switch which activated vehicle security system (theft warning alarm) is recorded. This mode is able to confirm and erase the record of theft warning alarm. The trigger data can be erased by touching R on ONSUT- screen. TV TST Test tem TT N V SURTY ORN MP() SR RTN PWR This test is able to check security indicator lamp operation. The lamp is turned on when ON on ONSUT- screen is touched. This test is able to check vehicle security horn operation. The horns are activated for 0.5 seconds after ON on ONSUT- screen is touched. This test is able to check headlamps operation. The headlamps are activated for 0.5 seconds after ON on ONSUT- screen is touched. This test is able to check hazard warning lamp operation. The hazard warning lamps are activated after ON on ONSUT- screen is touched. RTN PWR : ONSUT- unction ( - RTN PWR) NO:0000000006134058 ata monitor Monitor tem OOR SW-R OOR SW-S SN UR ndicates [ON/O] condition of driver side door switch. ndicates [ON/O] condition of passenger side door switch. S-30
< SYSTM SRPTON > NOSS SYSTM () SN UR : ONSUT- unction ( - SN UR) T MONTOR NO:0000000006059532 PUS SW [/] TV TST Monitor item [UNT] isplays the status of the push-button ignition switch (push switch) judged by. Test item Operation O PRSSUR SW O transmits the oil pressure switch signal to the combination meter via N communication, which illuminates the oil pressure warning lamp in the combination meter. S N O P S-31