ILLUSTRATED PARTS LIST MFG. ID NO. 9605101401 CUSTOMER CATALOG NO. TC 34T PRODUCT NO. 960 51 14-0 47 115 94 3-7
DECALS 7 14 7 14 4 7 5 9 11 13 9 1 4 3 11 6 51 57 97-01 Decal, Warning Eng. 4 59 94 99-01 Decal, Replacement 5 51 57 4-01 Decal, Lower Dash 6 51 57 3-01 Decal, Warning 7 51 6 73-01 Decal, Hood 59 51 47-01 Decal, Side Panel 9 51 57 9-01 Decal, Warning 11 51 57 91-01 Decal, Mower Cut Finger Symbol 13 56 0 03-01 Decal, Tractor Saddle 14 51 57 96-01 Decal, Chassis Hot Muffler 1 53 44 11-9 Decal, Belt Schematic 3 53 44 46-19 Decal, Bypass 4 53 44 54-93 Decal, Warning Combined - - 53 44 14-09 Pad Footrest LH - - 53 44 14-10 Pad Footrest RH - - 115 94 34-0 Manual Operator's (Euro) - - 115 94 36-10 Manual Operator's (Scan) - - 115 94 35-50 Manual Operator's (E-Bloc) - - 115 94 37-40 Manual Operator's (Baltic) WHEELS AND TIRES 1 11 3 7 6 4 10 5 9 1 53 05 91-9 Cap Valve Tire 53 06 51-39 Stem Valve 3 53 13 3-36 Rim Front 4 53 05 99-04 Tube Front (Service Item Only) 5 53 17 04-55 Tire Front 15 x 6-6 6 53 1 49-57 Fitting Grease (Front Wheel Only) 7 53 1 49-59 Bearing Flange (Front Wheel Only) 53 17 50-39 Cap Axle Blk 1 50 x 1 00 9 5 69 19-01 Tire Rear 1 x 9.5-10 53 1 49-6 Tube Rear (Service Item Only) 11 53 13 3-37 Rim Asm " Rear - - 53 14 43-34 Sealant, Tire (10 oz. Tube) wheel_art_1-tex NOTE: All component dimensions given in U.S. inches 1 inch = 5.4 mm
SCHEMATIC 3 SCH19 FUSE RED BATTERY C1 RED SOLENOID RED STARTER M WHITE WHITE CLUTCH/BRAKE (PEDAL UP) B G S M A1 L A BLK/WHT BLUE RED GREEN WHITE 5 6 C1 RED ELECTRIC CLUTCH GRAY PTO SWITCH (DISENGAGED) BLK/WHT REVERSE SWITCH (NOT IN REVERSE) GREEN YELLOW YELLOW SEAT SWITCH (NOT OCCUPIED) 3 1 GREEN 6 GRAY 9 C1 BAG FULL SWITCH (NOT FULL) SHORTING CONNECTOR BAG PRESENT SWITCH (BAG ATTACHED) /WHITE FULL BAG BUZZER BLUE IGNITION UNIT (OPTIONAL) HOUR METER SPARK PLUGS GAP ( PLUGS ON TWIN CYL. ENGINES) BLUE FUEL LINE BLUE 1V POWER OUTLET (OPTIONAL) FUEL SHUT-OFF SOLENOID (IF SO EQUIPPED) BLUE CHARGING SYSTEM OUTPUT 9-16AMPDC@3600 RPM REGULATOR STATOR LIGHT SWITCH ORANGE VOLTS AC @ 3600 RPM (REGULATOR DISCONNECTED) BROWN 4 BROWN C1 IGNITION SWITCH HEADLIGHTS POSITION CIRCUIT OFF M+G+A1 RUN/OVERRIDE B+A1 RUN B+A1 START B+S+A1 MAKE L+A 1 3 4 5 6 9 CHASSIS HARNESS CONNECTOR (C1) (MATING SIDE) DASH HARNESS CONNECTOR (C1) (MATING SIDE) 3 3 1 6 5 4 9 WIRING INSULATED CLIPS NOTE: IF WIRING INSULATED CLIPS WERE REMOVED FOR SERVICING OF UNIT, THEY SHOULD BE RE-INSTALLED TO PROPERLY SECURE YOUR WIRING. NON-REMOVABLE CONNECTIONS REMOVABLE CONNECTIONS
ELECTRICAL 3 TC11SM With Charge Indicator Option (If Equipped) 14 30 33 34 1 143 (+) (-) 0 60 AMPS 60 45 6 40 46 16 71 10 105 9 7 4 99 43 55 10 5 107 3 4
ELECTRICAL 3 1 53 43 71-57 Battery 53 44 09-3 Screw Hex Hd Cap M6 x 1.1mm 16 53 17 61-3 Switch Interlock Push-In 1 55 43 64-01 Harness Light 5 59 3 37-01 Cable Batt., Ga., Red 9, CRD 6 53 17 51-5 Fuse 7 73 51 04-00 Nut Keps Hex 1/4-0 unc 59 3 36-01 Cable, Batt. BLK10 9 53 40 15-45 Switch, Seat 30 53 19 33-50 Switch, Ign DLTA 33 53 41 19-35 Key/Chain Blisterpack 34 53 11 07-1 Switch, Light Reset 40 57 30 4-01 Harness Ign. Dash 4 53 13 15-63 Cover Terminal, Red 43 5 04-01 Solenoid 45 57 55 39-03 Ammeter Guage Round 46 57 55 40-03 Gauge Serviceminder HRMTR 50 5 10 76-01 Switch, PTO Terminal 55 17 06 05-1 Screw Thdrol 5/16-1 x 3/4 TYTT 71 53 44 0-0 Harness Ignition Chassis 3 53 43 67-74 Nut Square M6 x 1..5 x 11mm 99 17 00 05-1 Screw 5/16-1 x 3/4 Thrdl 10 53 44 1-6 Harness Jumper 105 53 40 75-6 Switch Reverse 107 53 1 03-79 Switch Full Bagger 10 59 50 03-01 Switch Snapmount 14 53 5 7-01 Charge Port Pigtail 143 53 44 0-59 Charge Port NOTE: All component dimensions given in U.S. inches 1 inch = 5.4 mm 5
TRACTOR - MODEL NO. TC 34T (9605101401), PRODUCT NO. 960 51 01-4 CHASSIS AND ENCLOSURES 39 0 15 97 96 9 03 130 130 130 3 130 14 350 5 14 06 336 130 37 137 130 176 1 151 375 130 5 0 177 3 176 4 99 130 137 375 191 07 04 344 19 130 175 345 195 05 335 176 13 350 36 194 199 1 36 176 194 176 7 51 53 16 367 13 159 307 30 6 334 6 119 4 47 10 119 194 309 56 30 30 11 34 19 55 33 5 15 340 341 17 19 55 339 30 46 11 343 13 30 30 5 6 36 303 30 46 6 6 159 194 57 150 35 30 49 36 34 159 50 319 6 19 5 54 16 30 35 6 37 16 36 1 34 41 19 304 159 56 347 307 19 chassis-texcrd-gen_tex GT HUSQ II_55 6 366 159 30 30
CHASSIS AND ENCLOSURES 39 NO. NO. DESCRIPTION 3 53 44 44-1 Applique 5 590 74 00-19 Dash 14 53 44 11-77 Hood 15 55 4 03-01 Lens LH 1 57 5 34-01 Grille 5 55 4 0-01 Lens RH 34 50 91 09-01 Plate Engine 36 17 06 05-1 Screw 5/16-1 x 3/4 37 53 44 13-69 Fender 5 73 6 05-00 Nut Lock 5/16-1 6 7 11 06-0 Bolt RdHd Sqnk 3/-16 x 1 Gr. 5 6 539 99 0-5 Screw Thdrol 5/16-1 x 1/ 11 19 13 13-16 Washer 13/3 x 13/16 x 16 Ga. 119 73 6 06-00 Nut Crownlock 3/-16 unc 130 53 41 63-5 Screw #10 x 0.750 137 53 40 75-90 Bumper Dash 150 53 43 97-74 Air Duct 151 53 43 66-70 Bracket Pivot 15 53 43 9-70 Shield Browning 159 17 00 06-1 Screw Hexwsh Thrd 3/-16 x 3/4 16 53 14 4-3 Screw 175 590 60 77-0 Crossmember Plate 176 53 40 07-76 Screw 10-4 x 5/ 177 53 19 5- Bushing Steering 10 53 90 7-01 Chassis 1 53 40 6-59 Dash Lower 13 74 5 05-0 Bolt 5/16-1 x 1-1/4 19 17 00 05-1 Screw 5/16-1 x 3/4 191 56 1-01 Insert Reflective RH 194 73 90 05-00 Nut Lock Hex Flange 5/16-1 195 53 40 41-37 Plug Hole Dash Lower 19 53 44 15-5 Indicator Deck Lift 199 53 41 7-39 Plate Deck Lift 0 53 43 97- Vent Side Hood RH 03 53 43 97-7 Vent Side Hood LH 04 53 44 06-65 Vent Top Hood 05 53 43 97-30 Skirt Hood Side RH 06 53 43 97-9 Skirt Hood Side LH 07 55 4 00-0 Bezel RH 0 55 4 01-0 Bezel LH 13 74 76 05-1 Bolt 5/16-1 x 3/4 14 53 19 91-45 Clip Retainer Tinner 17 53 40 91-67 Rod Pivot 1 53 19 63-95 X-Piece Hood Stop 53 19 51-61 Stud Fastner 9 53 44 14-63 Lid Ext 35 53 40 61-9 Spacer Fender 36 73 93 05-00 Nut Lock 5/16-1 unc 41 17 06 05-16 Screw 5/16-1 x 1 SMGML Tap/R 46 5 05 0-01 Spring TCRD Gen.5 Bagger Ext 47 5 55 6-0 Strap Battery TCRD Gen.5 x.431 4 7 11 05-04 Bolt Carr. 5/16 unc x 1/ 49 56 93 60-01 Screw Button 10-4 x 1/ PTCHD 50 539 97 69-77 Nut #10-4 Hex, Nylon Ring ZD 51 59 31 9-04 Backplate Support Bracket 5 51 99-04 Backplate Support Bracket 53 539 11 56-0 Bolt Carr. 1/4-0 x 3/4 54 73 90 04-00 Nut, Hex Flange 1/4-0 unc 55 59 39-0 Bolt Cross Drilled 3 /16 x 1.75 56 53 19 70-33 Nut Jam 3/-16 57 59 74 66-0 Bagger Latch Assembly LH 5 59 74 67-0 Bagger Latch Assembly RH NO. NO. DESCRIPTION 53 41 41-10 Clip Retainer 3 53 44 7-1 Console Deck Lift LH 4 53 44 7-0 Console Shft RH 7 17 60 04-06 Screw 1/4-0 x 3/ 96 55 4 05-01 LED Light LH 97 56 1 9-01 Insert Reflective LH 99 55 4 04-01 LED Light RH 303 57 49 31-0 Shield LWR LH 304 59 41 30-0 Shield LWR RH 307 57 49 45-01 Shield Upper French 30 53 17 1-77 Bolt 5/16-1 unc x 3/4 w/sems 309 5 55 5-0 Backplate 319 51 31 39-07 Lever Bag 334 53 44 5-37 Bracket Engine 335 53 44-04 Cover RH Lower Close Out 336 53 44 53-09 Cover LH Lower Close Out 33 53 43 66-40 Bolt Shoulder 339 53 43 66-41 Lever Bagger Full 340 5 55 7-0 Door Battery 341 5 06 0-01 Latch Battery Door Tex CRD 34 5 6-0 Supprt Fender 343 53 44 07-49 Clip 344 53 43 9-70 Control Ex Mulch Tex/CRD 345 53 44 06-39 Knob, Oval, Tapered 3/-16 BLK 347 53 44-7 Hitch Tow 350 53 44 51-43 Clip X-Mas Tree 366 51 31 46-0 Bracket RH Front Bagger 367 51 31 45-0 Bracket LH Front Bagger 36 51 4 4-01 Shroud Bag Full Lever 375 56 90-01 Dash Clip-On Bumper 37 590 4 9-01 Bushing Flange Plastic - - 53 43 1- Guard Brush - - 501 76 47-01 Kit ID Box This kit includes Battery Hardware (53 44 09-3 Screw Hex Head Cap M6 x 1.mm), 53 43 67-74 Nut Square M6 x 1..5 x 11mm; refer to pages 4 & 5 in this IPL, Chassis Parts/ Hardware (53 44-7 Tow Hitch), (53 43 66-41 Bagger Full Lever); refer to pages 6 & 7 in this IPL, Bagger Parts/Hardware (53 44 55- Bagger Spring Latch), (17 49 04-1 Screw Hexwsh Thdrol 1/4-0 x 3/4), (73 90 04-00 Nut Hex Flange 1/4-0 unc), (17 00 06-1 Screw Hexwsh Trdr 3/-16 x 3/4), (7 11 06-0 Bolt Rdhd Sqnk 3/-16 x 1 Gr. 5), (73 0 06-00 Nut Lock 3/-16 unc); refer to pages 1 & 19 in this IPL. NOTE: All component dimensions given in U.S. inches 1 inch = 5.4 mm 7
DRIVE 40 1 56 13 9 07 06 15 335 315 09 160 116 7 143 0 36 364 116 351 15 6 34 359 335 34 103 197 196 363 359 161 14 1 35 15 116 195 143 15 339 355 7 6 339 35 15 15 15 4 64 1 160 03 159 167 159 30 16 19 90 49 314 5 163 160 5 0 11 15 14 4 10 99 50 51 15 11 166 33 05 17 9 3 175 05 13 37 6 30 159 360 360 311 31 140 313 336 37 7 343 1 37 13 05 05 79 309 143 drive-texcrd-gen_k57r_pedal_ 73 33
DRIVE 40 1 Transaxle,Tufftorq K57AH (55743601) (Order parts from transaxle manufacturer.) 53 1 35-3 Key Square 6 53 1 40- Bushing Snap 17 53 43 6-7 Spring Brake K46 6 53 19 96-79 Spring Return Cruise 7 17 49 05- Screw Hexwsh Thd 5/16-1 x 1-3/4 9 53 44 7-95 Rod, Brake 30 19 13 16-16 Washer 33 1 00 00-01 Ring E 35 53 6 45-01 Rod, Brake, Park 37 53 1 9-67 Washer Harden.793 x 1.063 x.060 3 53 16 96-13 Nyliner Bushing 4 53 1 4-7 Cover, Foot Pedal 49 7 11 06-14 Bolt Rdhd 3/-16 unc x 3/4 Gr. 5 50 53 19 43-7 Idler Flat 51 73 90 06-00 Lock Nut 3/-16 5 53 19 43-6 Idler V-Groove 56 53 44 7-1 V-Belt, Drive 64 53 19 7-65 Shaft Asm. Pedal Brake Control 73 74 49 05-44 Bolt Flanged 90 53 44 36-05 Keeper Belt Clutching 9 74 76 05-0 Bolt Fin Hex 5/16-1 unc x 1.5 99 53 44 39-47 Rod Spring Bypass 103 73 35 05-00 Nut Hex Jam 5/16-1 116 73 90 05-00 Nut Lock Hex Flange 5/16-1 15 17 00 05-1 Screw 5/16-1 x 3/4 140 10 04 04-00 Washer Lock Hvy Helical 1/4 143 539 99 0-5 Screw 5/16-1 x 1/ 159 76 0 04-1 Pin Cotter 1/ x 3/4 160 53 16 94-4 Retainer Clip 161 53 10 57-09 Spring, Return, Clutch 163 53 44 7-93 Rod Control 166 53 4 91-64 Nut Push 167 53 40 5-57 Latch Brake Parking 175 53 4 93-59 Shaft Asm Crosshift Rear CRD 13 53 13 70-57 Spacer Axle 14 57 65 37-01 Handle Parking Brake 15 7 11 06- Bolt 3/-16 unc x -3/4 Gr. 5 16 53 19 43-1 Spacer Retainer 1 5 1 70-01 Link Clutch, Long 19 53 43 36-11 Bellcrank Ground Drive 195 50 45 69-01 Bracket Rod Brake CRD Tex 196 17 00 06-16 Screw 3/-16 x 1 Smgml Tap/R Blk 197 55 65 6-01 Link Clutch Anti-Rotation 03 19 11 11-16 Washer 11/3 x 11/16 x 16 Ga. 05 53 1 17-4 Washer 5/3 x 1-5/ x 16 Ga. 06 53 44 5-96 Bracket Mount Latch Cruise 07 57 03 14-01 Latch Control Cruise 0 53 19 7-69 Gear Sector Control Cruise 09 53 19 95-9 Rod Control Cruise 10 53 40 09-0 Rocker Asm. Pedal Control 11 53 1 01-3 Bearing Nylon 13 53 40 31-19 Knob Control Cruise 14 53 41 6-63 Pedal Forward 15 56 60 65-0 Pedal Reverse 1 53 40 31-7 Retainer Spring Clip Handle 79 1 0-10 Washer 1/3 x 1-1/4 10 Ga. 6 53 40 15-64 Bracket Strap Torque 7 17 49 05-1 Screw 79 53 44 4-3 Link Shift 0 19 11 10-1 Washer 11/3 x 5/ x 1 Ga. 4 53 41 76-93 Nut 5 74 1 04-1 Screw 309 53 16 55-1 Plate Fstnr Cross Shf 311 53 16 9-45 Washer Nylon 31 53 16 56-14 Hub Tapered 313 74 7 04-16 Bolt Hex Fin 1/4-0 unc x 1 Gr. 5 314 53 44 47-13 Keeper Belt 315 17 5 05-0 Screw Thdrol 5/16-1 x 4.5 335 53 19 95-34 Pulley V-Idler 336 57 5 96-01 Bolt 5/16-1 x 1-3/4 Flanged hex 339 53 43 6-67 Strap Torque K46 CRD Tex 34 53 1 6- Keeper Belt.5" STL V-Idlr CRD 343 539 11-99 Nut 5/16-1 Hex Flanged Nyloc 351 53 43 69-9 Bracket 97 CRD Deck Sway 35 53 43 56-45 Bracket Idler CRD Tex 355 53 43 56-69 Bracket 359 17 49 06-10 Screw Thdrol 3/-16 x 5/ 360 53 44 47-14 Nut 5/16-4 unf 36 53 43 6-1 Idler Flat 363 53 44 7-0 Spacer.343 x.63 x.6 364 53 44 30-3 Bracket Idler CRD Tex 37 5 65 49-01 Keeper Belt Transaxle NOTE: All component dimensions given in U.S. inches 1 inch = 5.4 mm 9
ENGINE 4 1 116 1 10 0 45 69 6 9 1 9 71 137 97 96 90 90 9 1 6 70 15 1 11 37 5 41 4 43 10 9 37 43 SPARK ARRESTER KIT Guard_assembly_5 engine-tex_kawa-cyl_59-10
ENGINE 4 1 Engine KAWA Model No. FR651V (5949301) (Order parts from engine manufacturer.) 53 44 59-6 Muffler 9 501 3 6-0 Keeper Belt Engine 11 57 4 16-01 Clutch Electric 1 53 40 50-97 Pulley Engine 15 53 43 5-16 Tank Fuel 1 53 44 14-6 Fuel Cap 0 53 4 43-41 Control Throttle 1 53 41 63-5 Screw # 10 x 0.750 53 1 95-41 Control Choke 57 04 4-0 Fuel Line 9 53 13 71-0 Spark Arrester Kit 37 53 1 34-7 Clamp Hose 41 53 1 61-97 Washer 1-1/ OD x 15/3 ID x.50 4 539 99 0-47 Washer Lock 7/16 43 17 06 05-16 Screw 5/16-1 x 1 SMGML Tap 45 73 51 04-00 Nut Keps Hex 1/4-0 unc 6 53 43 40-17 Shield Heat Muffler 69 53 17 1-51 Gasket 70 53 95 56-01 Tube Exhaust LH 71 53 95 57-01 Tube Exhaust RH 1 53 14 4-56 Tube Drain Oil Easy 5 501 60 66-01 Bolt Hex 7/16-0 x 3.75 Gr. 5 6 53 1 43-6 Nut Hex Flanged Toplock 90 17 00 06-16 Screw 3/-16 x 1 9 17 1 06-16 Screw 3/-16 x 1 SMGML Tap/R 96 19 09 14-16 Washer 9/3 x 7/ x 16 Ga. 97 17 67 04-1 Screw 1/4-0 x 3/4 10 17 00 05-1 Screw 5/16-1 x 3/4 10 57 17 95-10 Cover Pulley Engine 116 539 13 6-4 Knob Shift 137 53 44 14-61 Spill Cup NOTE: All component dimensions given in U.S. inches 1 inch = 5.4 mm 11
STEERING ASSEMBLY 41 6 50 45 1 1 16 64 7 63 75 60 63 76 9 19 59 7 67 66 9 7 1 35 1 5 4 6 67 6 5 61 69 14 15 6 14 13 6 70 15 13 53 steering-tex_husqsr_67_r1 1
STEERING ASSEMBLY 41 1 53 43 97-40 Wheel, Steering 53 19 59-6 Axle Cast Iron 4 53 40 30-7 Spindle Asm., LH 5 53 40 30- Spindle Asm., RH 6 53 1 49-31 Washer Thrust 0.75 x 1.3 7 53 1 17-4 Washer 5/3 x 1-5/ x 16 Ga. 1 00 00-9 Ring, Klip #T5304-75 9 53 1 1-3 Cap, Spindle 13 53 1 17-49 Washer 5/3 x 1-1/4 x 16 Ga. 14 539 99 01-1 Washer, Lock 3/ 15 73 54 06-00 Nut, Crown Lock 3/-4 unf 16 57 01 60-0 Shaft Steering 19 53 19 47-9 Plate Steering 1 56 4 0-01 Adapter, Wheel Steering Splnd Alum 55 0 9-0 Bearing Shaft Steer Low 6 53 43 97-43 Insert, Wheel Steering 7 19 1 16-16 Washer 1/3 x 1 x 16 Ga. 17 00 06-1 Screw 3/-16 x 3/4 35 53 19 47-3 Gear, Sector Plate 45 57 01 64-01 Washer 3/ ID -3/OD 1 Ga. PLTD 50 73 90 06-00 Nut Lock Flg. 3/-16 unc 53 53 1 9-67 Washer Hardened.793 x 1.637 x.060 5 53 19 47-47 Bolt Shoulder Sector Pivot CFM 59 53 19 47-4 Washer Thrust Sector Steering 60 73 97 10-00 Nut Flange Lock 5/-11 61 5 79 44-0 Draglink, LH 6 5 79 45-0 Draglink, RH 63 17 00 05-1 Screw 5/16-1 x 3/4 64 53 19 9-49 Retainer Clip Spring Steering 66 71 0 07-4 Bolt Hex Fghd 7/16-14 x 3 Serr 67 53 19 47-37 Bushing PM Front Axle 6 73 90 07-00 Nut Lock Flange 7/16-14 Gr. 5 69 53 19 91-6 Washer 1.5 x.505 x.11 70 55 33-01 Bracket Deck Susp. Front 75 50 6 37-01 Pinion 76 50 6 36-01 Screw Head Sock 1 53 44 49-6 Cap Gear Sector NOTE: All component dimensions given in U.S. inches 1 inch = 5.4 mm 13
MOWER DECK 44 16 101 17 43 75 14 116 11 10 11 10 7 11 4 11 49 14 140 13 15 95 4 43 17 11 13 110 111 115 114 119 137 136 139 13 17 1 7 91 139 16 105 159 16 117 17 1 117 75 76 154 91 16 11 1 5 3 97 19 96 5 117 75 160 14 117 4 5 50 50 50 119 115 11 19 154 117 113 5 5 50 50 50 110 117 101 5 94 9 117 161 14 147 3 1 16 91 1 47 64 100 19 130 131 9 99 117 16 117 11 104 17 11 164 55 55 117 3 100 33 34 45 14 16 91 1 17 55 35 5 141 55 tex-deck_texcrd-gen_95 157 156 55 39 15 165 41 7 156 3 6 14
MOWER DECK 44 1 50 97 33-01 Deck Weldment 53 4 30-6 Palnut 1/4 3 73 90 05-00 Nut Lock Hex Flange 5/16-1 5 17 00 05-10 Bolt 5/16-1 Hex Whs Hd Lckserr 11 53 13 77-9 Screw Thd Roll 1/4-0 x 5/ 13 7 11 06-1 Bolt Carr Sh 3/-16 x 1-1/ Gr. 5 14 53 15 60-5 Keeper Belt Idler 16 73 90 06-00 Nut Lock FlG 3/-16 unc 17 53 40 0-34 Nut Flange Lock Top 1 53 1 76-90 Washer, Spacer, Mandrel 19 55 3 39-01 Bearing Mandrel 3 17 49 06- Screw Thdrol 3/-16 x 1-3/4 7 53 44 5-7 V-Belt Drive 3 53 44 6-05 Spring Return Deck 33 53 1 7-1 Mandrel Asm. Tall 34 57 5 65-01 Shaft Asm Mndrl 35 53 1 05-3 Blade Mower LH 3 590 40-01 Bolt Blade 7/16-0 x 1.5 Gr. 39 51 5 65-01 Washer 7/16 Flat 41 539 99 0-47 Washer lock 7/16 4 17 00 05-1 Screw 5/16-1 x 3/4 43 53 44 3-39 Pulley Mandrel 45 53 13 71-5 Mandrel Asm. Short 7 51 45 41-03 Chute Upper 75 53 13 14-94 Pulley Idler Flat 76 53 43 96-40 Washout Port 4 53 44 3-35 Keeper Belt Mandrel 5 53 1 05-4 Blade Mower RH 6 53 1 17-13 Bolt 3/-4 x 1.50 Gr. 7 539 99 01-1 Washer Lock Hvy 3/ 53 14 0-96 Washer, Hard, Blade, Mover 91 19 13 0-1 Washer 13/3 x 1-1/4 x 1 Ga. 94 53 19 7-50 Bracket Clutch Cable 95 17 00 06-1 Screw 3/-16 x 3/4 96 53 40 0-71 Spacer 97 53 1 0-61 Shield Idler Mower 9 53 19 51-61 Stud Fastener 99 53 19 51-6 Arm Suspension Mower Rear 100 53 19 65-39 Bolt Shoulder 101 73 6 09-00 Nut Crownlock 9/16-1 unc 10 53 40 5-11 Spacer Bearing Swing Plate 104 51 71 40-01 Mandrel Cover RH 105 53 44 47-55 Mandrel Cover LH 110 57 93 4-01 Gear Output 111 53 43 69-79 Gasket Gearcase 11 53 44 3-5 Shaft Gearcase 113 53 43 5-33 Plug Oil 114 5 17 05-01 Valve Relief 115 1 03 10-16 Screw Torx #10-4 x 1 116 7 11 04-14 Bolt 1/4-0 x 1.75 Gr. 5 117 73 90 04-00 Nut Hex Flange 1/4-0 unc 11 53 44 3-3 Arm Clutching 119 53 43 1-66 Gearcase Subasm 10 53 44 3-36 Keeper Belt RH 11 53 43 69-5 Washer 14 53 43 69-6 Non Greasable Mandrel Shaft 15 53 43 69-94 Bracket Idler Chassis 17 53 19 34-06 Bolt Shoulder 3/-16 x 3-5/ Gr. 5 1 59 5 73-01 Wheel Gauge 19 53 44 3-37 Rod Anti-Sway 130 19 13 13-1 Washer 13/3 x 13/16 x 1 Ga. 131 53 19 4-0 Pin Cotter 5/16 Bow Tie Lock 133 53 43 1-97 EZ Mulch Door 134 53 43 5-61 Pin Hinge 135 53 43 79- E-Ring 5/16 136 53 43 96-39 Washout Port Remote Hookup 137 1 00 00-9 Ring Klip 13 53 44 76-67 Hose Washout Port 139 53 44 07-4 Hose 3/ Clamp 140 501 5 00-01 Guard Asm. LH 141 501 57 96-0 Guard Asm. LH 146 53 44 5-96 Spring Tex CRD EZ Mulch 147 59 39 9-01 Bolt Crss DRLD 3/-16 x 1.75 14 53 19 70-33 Nut Jam 3/-16 154 53 19 9-55 Screw 1/4-0 Panhead 156 53 44 69-95 Adapter Weldment Blade 157 53 44 69-93 Blade Cross LH 107 15 53 1 04-5 Blade Cross RH 107 159 55 30 94-05 Plate LH Side 160 55 30 95-05 Plate LH Front 161 55 31 60-05 Plate RH Front 16 55 31 61-05 Plate RH Side 164 59 35 5-0 Baffle Plate LH 165 57 4 61-0 Baffle Plate RH 47 59 00 96-0 Guard Steel Mandrel Cover RH 4 51 6 36-0 LH Rear Steel Guard 49 51 6 35-0 LH Front Steel Guard 50 19 11 1-1 Washer 11/3 x 3/4 x 1 Ga. 55 539 10 9-00 Carriage Bolt 1/4-0 x 1 Gr. 5 5 54 95 39-01 Bolt Hex Wsh Hd.316-1 x 1.19 64 59 39 9-01 Retainer Asm. Upper Chute - - 57 5 33-01 Mandrel Assembly Tall (Includes Housing (key #33), Shaft Assembly (key #34), And Bearing Only (key #19) - Pulley/Nut/ Washer And Blade Bolt/Washers Not Included) - - 59 64 4-01 Replacement Mower Complete - - 53 44 1-3 Gear Case Kit Use.75 oz. Shell 460 oil (Include Gear Output (key #110), Gasket Gearcase (key#111), Shaft Gearcase (key #11), Plug Oil (key #113),Vent Breather 1/ NPT (key #114), Screw Torx (key #115), Gearcase Subasm (key #119)) NOTE: All component dimensions given in U.S. inches 1 inch = 5.4 mm 15
MOWER LIFT 45 7 7 90 9 116 10 3 97 100 91 97 7 9 101* 9 7 lift-tex_50 *Key 91 may be substituted for Key 101 53 43 69-96 Deck Lift Weldment 3 53 19 5-31 Lever Asm., Lift RH 7 50 96 3-01 Grip, Lever 10 53 19 63-14 Spring Torsion 7 53 19 4-09 Pin Cotter 7/16 Bow Tie Lock 53 44 54-96 Spring Lift Assist 9 19 19 19-1 Washer Clear Zinc 90 53 19 4-0 Pin Cotter 5/16 Bow Tie Lock 91 53 19 51-1 Link Lift Susp Mower Rear 97 17 49 06-0 Screw 3/-16 x 1/ 9 53 19 5-70 Link Lift Susp. Front Mower 100 73 93 06-00 Nut Centerlock 101 53 40 70-03 Link Asm. Lift 116 19 15 15-16 Washer 15/3 x 15/16 x 16 Ga. NOTE: All component dimensions given in U.S. inches 1 inch = 5.4 mm 16
SEAT ASSEMBLY 4 1 7 7 41 40 10 1 6 37 44 44 43 37 43 1 3 seat-tex_6.5sl_6_r1 1 5 55 67-01 Seat 53 1 01-66 Bracket Pivot Fender 3 53 14 06-75 Strap, Asm Fender 6 73 0 06-00 Nut, Lock W/Ins. 3/-16 unc 7 59 4 35-01 Spring, Seat Cprsn 53 17 1-77 Bolt 5/16-1 unc x 3/4 w/sems 10 57 3 0-0 Pan, Seat Plate 1 57 90 7-01 Bolt, Shoulder 5/16-1 x 5/ 37 73 0 05-00 Nut, Lock 5/16-1 unc 40 53 19 76-61 Handle Slide Seat 41 53 19-00 Spring Latch Seat 43 74 76 06-1 Bolt Fin Hex 3/-16 unc x 3/4 44 501 05 1-01 Washer 13/3 x -3/ x 1 Ga. NOTE: All component dimensions given in U.S. inches 1 inch = 5.4 mm 17
BAGGER 46 7 70 6 5 1 53 4 3 94 47 3 43 44 45 4 3 4 46 19 44 44 51 55 65 59 56 54 3 3 95 3 4 3 93 44 5 5 55 59 65 65 10 56 4 9 95 50 44 3 9 3 4 49 5 49 3 49 7 5 70 3 4 3 50 69 1 Bagger_TexCRD-Gen_11 1
BAGGER 46 1 53 4 6-10 Tube Handle Bagger 53 44 75-7 Applique 3 53 17 4-14 Clip 5 53 44 37-6 Upper Pivot Tube 53 44 75-75 Bagger Top 10 53 44 37-55 Frame Front 19 53 19 4-0 Cotter Pin 5/16 Bow Tie 1 51 33 71-03 Bag Asm 7 53 44 55-9 Grommet Rubber 53 16 57-7 Grip Handle 4 53 44 04- Clip 43 53 1 6-75 Clevis Pin 44 53 19 96-7 Bolt 1/4-0 45 53 44 37-54 Upper Frame 46 53 44 55-41 Bag Corner Close Out RH 47 53 44 40-79 Bag Corner Close Out LH 4 53 44 40-0 Top Bagger Side Close Out 49 53 17 1-73 Bolt Shoulder 5/16-1 50 53 17 1-77 Bolt 5/16-1 x 3/4 W/Sems 51 7 11 05-06 Bolt 5/16 x 1 x 3/4 5 73 0 05-00 Nut Lock Hex W/Ins 5/16-1 unc 53 53 44 41-95 Bracket Dump Handle 54 53 44 7-1 Bagger Top Front Handle 55 539 10 9-33 Bolt 5/16-1 x 1-1/ 56 53 4 03-06 Pin Clevis.13 x 1.6 59 53 44 47-63 Bagger Sprd Tube 65 53 1 47- Retainer Spring 69 53 4 1-01 Screw # Flat Head Drill 70 17 00 06-1 Screw 3/-16 x 3/4 3 73 0 06-00 Nut Lock Hex w/ins. 3/-16 unc 4 7 11 06-0 Bolt 3/-16 x 1 Gr. 5 5 51 31 44-0 Bracket RH Pivot 6 51 31 43-0 Bracket LH Pivot 7 51 31 4-0 Bracket RH 51 31 47-0 Bracket LH 9 51 31 51-04 Weldment Offset Strut 9 56 05 3-0 Bracket Top Support 93 56 05 4-0 Bracket Support RH 94 56 05 5-0 Bracket Support LH 95 17 00 05-1 Screw 5/16-1 x 3/4 - - 501 70 56-01 Bagger Dump Kit (Includes Key#'s 5, 6, 7,, & 9) NOTE: All component dimensions given in U.S. inches 1 inch = 5.4 mm 19
09.1.017 JSE