QUICK CHANGE DUAL FILTER SYSTEM page 1 of 5 130mm 290mm 70mm 380mm 100mm (filter unit depth) 180mm Dimensions are nominal measurements only. 1. 3/4 Multifunction valve 2. Filter isolating valve 3. 90 deg elbow fitting 4. 3/8 Flexible tube 5. PP filter 6. Disruptor filter 7. Filter housing 8. 3/8 Flexible tube CLEANING RECOMMENDATIONS 9. Flexible tube to thread tap connector 10. Lock nut 11. Shake proof washer 12. Black locating washer We recommend the use of soapy water or approved cleaners. 13. Rubber O-ring 14. Chrome plated sink mount 15. Chrome plated tap body and handle 16. Chrome plated tap spout 17. Above and below sink This product should not be cleaned with abrasive materials. Damage caused by any improper treatment is not covered by the product warranty- refer to Warranty Conditions To see the complete Mizu range go to www.reece.com.au/bathrooms AS/NZS 3497 Lic. WM-022281 Disclaimer: Products in this specification manual must by regulation be installed by licensed and registered trade people. The manufacturer/distributor reserves the right to vary specifications or delete models from their range without prior notification. Dimensions are nominal measurements only. Dimensions and set-outs listed are correct at time of publication however the manufacturer/distributor takes no responsibility for printing errors. Tech Page Version 3
page 2 of 5 130mm 290mm 16 1 7 2 3 14 13 12 11 10 17 15 70mm 380mm 9 5 6 8 4 100mm (filter unit depth) 180mm 1. 3/4 Multifunction valve 2. Filter isolating valve 3. 90 deg elbow fitting 4. 3/8 Flexible tube 5. PP filter 6. Disruptor filter 7. Filter housing 8. 3/8 Flexible tube 9. Flexible tube to thread tap connector 10. Lock nut 11. Shake proof washer 12. Black locating washer 13. Rubber O-ring 14. Chrome plated sink mount 15. Chrome plated tap body and handle 16. Chrome plated tap spout 17. Above and below sink
page 3 of 5 Installation Instructions Fitting into s/steel braided hose line 1. Isolate water supply to kitchen tap. 2. Turn on kitchen tap to release pressure in pipe then turn tap off 3. Find a convenient location for the filter system under the sink, taking into consideration ease of access for servicing and best use of cupboard space (5,6,7). 4. Disconnect 1/2 copper pipe or s/steel braided hose at the stop cock, and insert the 3/4 multifunction valve using instructions supplied with the valve (1). 5. Install filter isolation valve (2) into the multifunction valve and insert the 90 deg elbow (3) into the end of the isolation valve. 6. The valve should be in off position. Turn water supply on, slowly turn the kitchen tap on and check for leaks Drill hole in sink for tap 7. Select location for tap (consider ease of use). Check that there are no obstructions under the sink 8. First drill 3mm pilot hole. Then drill 1/2 final hole. N.B. Use slow speed drill. Excessive speed may blunt drill and discolor stainless steel. 9. Mount tap onto sink (9 to 16). Connecting system for use 10. Cut suitable length of the 3/8 tubing (4), fit to the elbow (3) 11. Insert 3/8 tubing firmly into quick connector (7) on filter inlet 12. Cut suitable length of the 3/8 tubing, install it to the 3/8 quick connector on the filter outlet (7) and insert the other end to the tap connector (9). 13. After all tubing has been connected. i.e. from the plumbing valve to the inlet side of the system and from the outlet side to the tap. Place the tap in the open position, then open the filter isolating valve slowly. This will allow any air to escape. (Check for leaks and adjust if necessary). 14. Let the system run for a few minutes to flush the filter cartridge. 15. Allow the system to stand for 2 to 3 hours and then flush again for several minutes. The system now is operational. Water flow reduction usually indicates clogging of filter cartridges. Filter cartridge should be changed based on filter changing instructions. The service life will vary due to water quality and usage. Changing filter cartridge 16. Turn filter isolating valve (2) off and open sink tap to vent pressure 17. To remove the filter: turn filter 1/4 turn to the left. The filter will rotate away from the filter head. Pull the filter down to remove. 18. To replace the filter: Insert filter into the filter head. Turn filter 1/4 turn to the right until it stops. The top surface of the filter will be flush with the bottom of the filter head when fully installed. 19. Slowly turn on the filter isolating valve to expel air and initial water flush. See points 14-15
Cautions and Warnings I nstallation must comply with AS/NZS 3500 or Local Plumbing codes maximum operating pressure: 1250 kpa; the minimum operating pressure: 50 kpa. maximum operating temperature is 38 C, and the minimum operating temperature is 4 C. N ominal flow rate is 7.5 L/min P rotect the filter from freezing, failure to do so may result in it cracking and leaking D o not install where the unit will be exposed to direct sunlight or freezing Do not install this system using copper solder fittings. The heat from the soldering process will damage the unit. U se PTFE thread tape at all threaded joints water filter should be used only on water that is microbiologically safe. This is water that has been adequately chlorinated or disinfected for bacteria protection, either before or after filter system. page 4 of 5 This appliance meets the domestic water treatment appliance Standards AS/NZS 3497 and AS/NZS 4348 for the following water treatment process: Treatment and tests Class Treatment Type Function Pass I II II(a) Microbiological Status Bacteriostatic Will stop bacteria increasing, but will not remove them unless II(a) is ticked N/A Microbiological Treatment Bacterial removal Will remove or inactivate bacteria N/A II(b) Virus removal Will remove or inactivate virus N/A II(c) Protozoa removal Will remove or inactivate Cryptosporidium and Giardia III Turbidity and particulate reduction Will reduce cloudiness IV Taste and odour reduction Will reduce taste and odours V Chemical treatment Removes Chlorine Substance Australian Drinking Water Guidelines Influent Maximum Effluent Minimum Percent Removal (%) Effluent Percent Removal (%) Turbidity <1 NTU 10498 1165 89.0 1156 89.0 Particles/mL Particles/mL Particles/mL Chlorine 5.0 mg/l 2.0 mg/l 0.26 mg/l 84.0 0.23 mg/l 88.6 Testing Conditions - Flow rate: 5.5 LPM, Pressure: 60 psi, ph: 7.75, Temp: 22 C Important The filter must be maintained and the filter cartridges changed periodically as recommended. Record the date of installation to remind you when your cartridges need changing. Recommended to replace after 6 months. This may vary depending on water quality. Distributor: Reece Australia Ltd. 118 Burwood Highway, Burwood Victoria 3125 Tel: +613 9274 000 For further technical information or assistance, contact 1800 032 566 or visit www.reece.com.au for your nearest Reece showroom
page 5 of 5 7YEAR QUALITY GUARANTEE REECE PRODUCT QUALITY GUARANTEE You have purchased a quality product from Reece Pty Ltd ABN 84 004 097 090 ( Reece ). This product is covered by a 7 year replacement product warranty and a 12 month warranty over spare parts and labour. 7 YEAR WARRANTY DOMESTIC USE This warranty covers faults in the product construction, material and assembly. Products which are within 7 years from the date of purchase, found upon inspection by an authorised Reece representative, to be defective in construction, material or assembly, will be repaired or exchanged with an equivalent product free of charge. Replaced items become Reece s property. This warranty also covers any spare parts included under Manufacturer s Provisions below. All replacement products will be available for collection without charge to the customer at the nearest Reece branch to the customer s location, or elsewhere as agreed between the customer and Reece. Manufacturer s Provisions The following spare parts are covered by a 7 year warranty: Labour and Spare Parts The labour for the replacement of products and spare parts to which this warranty applies will be supplied by Reece or relevant supplier using licensed plumbers engaged by Reece or relevant supplier within 1 year from the date of purchase. Filter cartridges are not covered by labour and spare parts warranty. Cartridges need to be replaced by the end user periodically as per the usage instructions. Spare parts other than those listed in the Manufacturer s Provisions above, which are within 1 year from the date of purchase found upon inspection by an authorised Reece representative to be defective in construction, material or assembly, will be replaced free of charge. Warranty Conditions This warranty will apply only under all of the following conditions: The item has been installed by a licensed plumber The item has been installed for and subjected to domestic residential use only Failure is due to a fault in the manufacture of the product Proof of purchase (including the date of purchase) is provided The installation of the product is in accordance with the instructions provided This warranty does not cover products purchased as an ex-display without being fully checked and tested for sale by the manufacturer. This warranty does not include faults caused by: Unsuitable or improper use Incorrect installation or installation not in accordance with the instructions provided Installation or part installation by the purchaser or any person other than a LICENSED PLUMBER Normal wear and tear Inadequate or complete lack of maintenance Chemical, electrochemical or electrical influences Harsh detergents or abrasive cleaners used on product finishes 1 YEAR WARRANTY COMMERCIAL USE Commercial use is all use other than for normal domestic residential purposes, including use in non-business places as in public buildings, schools, sports centres and in establishments that contain private bathrooms with high frequency of use by many individuals, such as hotels, motels, retirement villages and hospitals. The Commercial warranty covers this product against manufacturing faults in the construction, material and assembly of both the finished products and any spare parts for a period of 1 year from the date of purchase. Products and spare parts which are found upon inspection by an authorised Reece representative to be defective in construction, material or assembly will be repaired or exchanged free of charge. Replaced items become Reece s property. The labour for the replacement of products and spare parts/ water filter cartridges to which this warranty applies will be supplied by Reece or relevant supplier using licensed plumbers engaged by Reece or relevant supplier. The Warranty Conditions and exclusions which apply to the domestic use warranty also apply to this commercial warranty. EXCLUSIONS To the fullest extent permitted by law, Reece excludes all liability for damage or injury to any person, damage to any property, and any indirect consequential or other loss or damage. CLAIM PROCEDURE For all warranty queries customers are to contact the branch where the product was purchased. These details can be found on your purchase invoice. Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. WATER FILTER/TAPT1.7YR Don t risk it, use a licensed plumber.