Section 00 Chapter 3 GENERAL SPECIFICATIONS AND SPECIAL TORQUES 6-13870NH
TABLE OF CONTENTS GENERAL SPECIFICATIONS... 0-3 Fluid Capacities and Types... 0-3 Hydraulic Specifications... 0-3 Electrical Specifications... 0-3 Cab Fuse Identification and Amperage... 0-4 Cab Relay Identification (Facing Rear Window)... 0-5 Engine Compartment Fuse/Relay Identification (Power Distribution Box)... 0-5 Lamps and Bulbs... 0-6 Accessory Connectors... 0-6 Air Conditioner System Specifications... 0-7 Engine Specifications... 0-7 Transmission Specifications... 0-7 Hitch Specifications... 0-7 SPECIAL TORQUES... 0-8 00-2
Fluid Capacities and Types GENERAL SPECIFICATIONS All fluid capacities listed are a guide to the quantities required. Always use dipsticks, sight glasses or level plugs to ensure that the units are filled to the correct level. Coolant Capacity TG 210 and 230... 22.7 liters 6 U.S. gal TG 255 and 285... 24.6 liters 6.5 U.S. gal Fluid Type... 50 Percent Ethylene Glycol and Water Engine Oil Capacity With Filter Change... 21 liters 5.5 U.S. Gal Without Filter Change... 19 liters 5 U.S. Gal Oil Type...NH No. 1 Engine Oil Transmission/Hydraulic System Capacity MFD... 172 liters 45.5 U.S. gal Oil Type... New Holland Ambria 134D MFD Axle Differential 10 Bolt... 12.3 liters 13 quarts 12 Bolts... 11.3 liters 12.3 quarts Supersteer (all)... 10.5 liters 11.1 quarts Oil Type...API GL5 SAE 85W-140 Planetary (Each) 10 Bolts... 1.3 liters 2.8 U.S. pints 12 Bolts... 3.2 liters 6.8 U.S. pints Oil Type... SAE 85W-140 Gear Lubricant Fuel Tank Standard - TG 210 and 230... 492 liters 130 U.S. gal Standard - TG 255 and 285 (Optional - TG 210 and 230)... 606 liters 160 U.S. gal Fuel Type... No. 2 Diesel Hydraulic Specifications Pump Type... Axial Piston, Closed Center Load Sensing Maximum Pressure at Rated Engine RPM at Pump...224 bar 3250 psi Maximum Flow at Remote Couplers at 2000 Engine RPM Standard... 136 l/min 36 gpm Optional Mega Flow... 244 l/min 64 gpm Electrical Specifications Type of System...12 Volt Negative Ground Batteries...Two 1000 CCA Low Maintenance, Group Size 31 Alternator...Bosch 135 Amp Output Cranking Motor...Nipendenzo, 12 Volt, 4 kw 00-3
Cab Fuse Identification and Amperage 50 51 15A 52 15A 53 54 55 56 ITALIAN BRAKES 5A 43 15A 44 15A 45 46 30A 47 30A 48 20A 49 30A ICU/PMU ECU 36 15A 37 5A 38 10A 39 10A 40 10A 41 5A 42 10A SW B+ CONTROLLER AFS TRANS CONT. 29 10A 30 31 10A 32 5A 33 10A 34 SW B+ UNSW. B+ STOP 22 10A 23 15A 24 10A SUSP. AXLE 25 20A 26 10A 27 LIGHTS SW. B+ 5A 35 28 C /F TEMP. DISPLAY 5A 15 30A 16 ICU/PMU 5A 17 5A 18 10A 19 10A 20 20A 21 10A UNSW B+ 8 20A 9 15A 10 15A 11 20A 12 30A 13 30A 14 372943A1 1 5A 2 3 20A 4 10A 5 20A 6 10A 7 10A RI02G018 Fuse No. Circuit 1 Electronic Governor (TG 255 & TG 285) 5 2 Cruise Control 5 3 Rear Fender Worklights 20 4 Beltline Worklights 10 5 Roof Worklights 20 6 Worklight/Headlight Interlock 10 7 Battery Power to Key Switch 5 8 Headliner Shelf Auxiliary Power/3-Pin/ Cigar Outlets (Unswitched) 9 Seat Power 15 10 Cab Pressurizer Blower (Continuous) 15 Fuse Amp 11 Cigar Lighter/RH Fender Console (Unswitched) 20 12 Exterior 7-Pin Connector (Switched) 30 13 RH Front Post/RH Fender 3-Pin Auxiliary Connectors (Unswitched) 30 15 Governor (MX255 & MX285) 30 16 Tractor Instrumentation (Unswitched) 5 18 High Beam Relay 10 19 Dome Light/Map Light/Radio (Unswitched) 10 20 Amber Flashers 20 21 Tail Lights 10 22 Stop Lights 10 23 Strobe Light/Beacon 15 20 Fuse No. 24 Mirror/Radio 10 25 Ether/Horn 20 28 Circuit Auto Climate Display (With Fuse = C, Without Fuse = F) 29 Seat Heater 10 31 AFS (Switched) 10 32 AFS (Unswitched) 10 33 RH ArmRest Controller (Switched) 10 34 True Ground Radar 5 35 Transmission Controller 20 36 Remote Hydraulic Controller 15 37 Tractor Instrumentation (Switched) 5 38 PTO/Differential Lock/MFD Controller 10 39 Hitch Controller 10 41 Case Data Bus, Tractor 5 42 Case Data Bus Diagnostic Connector 10 46 RH Front Post/RH Fender 3-Pin Connectors (Switched) 30 47 HVAC Controller 30 48 Headliner Shelf 3-Pin Connectors (Switched) 20 49 HVAC Blower 30 51* Front Wiper/Washer 15 52 Rear Wiper/Washer 15 56 Italian Brakes 5 Fuse Amp 5 (Unswitched) - Unswitched power (Continuous). (Switched) - Power available when keyswitch is in ON position. * = Circuit breaker. 00-4
Cab Relay Identification (Facing Rear Window) 4 1 10 7 19 5 2 11 8 6 3 12 9 RH02G061 1. BRAKE LAMPS 6. NEUTRAL RELAY 11. GOVERNOR (KEY SWITCH) 2. OPEN 7. OPEN 12. FENDER WORK LAMPS 3. REAR ROOF WORK LAMPS 8. BELTLINE WORK LAMPS 19. CONTROLLER POWER 4. WORK LAMP INTERLOCK 9. FRONT ROOF WORK LAMPS 5. PARK LATCH 10. CAB PRESSURIZER BLOWER Engine Compartment Fuse/Relay Identification (Power Distribution Box) STARTER FUEL SHUT OFF 6 7 10 11 25 F6 30 F7 25A 30A 16 17 3 4 (D1) (D2) (3) (4) 12 30A 15A CENTER & SIDE 25A 30A 13 14 25 F1 30 F2 1 2 HIGH BEAM LOW BEAM 8 9 15 F8 15 F9 15A 15A 5 15 F5 15A (D1) (D2) 15 HIGH BYPASS RH02G062 1. CENTER SIDE & HID 6. FUEL SHUT OFF RELAY 11. FUEL SHUT OFF RELAY 16. DIODE 1 WORKLAMP RELAY FUSE FUSE 2. HIGH/LOW BEAM & 7. STARTER RELAY FUSE 12. CENTER AND SIDE 17. NOT USED - DIODE 2 BYPASS RELAYS FUSE WORKLAMP RELAY 3. STARTER RELAY FUSE 8. RH LO BEAM RELAY FUSE 13. HIGH BEAM RELAY 4. RH HI BEAM FUSE 9. LH LO BEAM RELAY FUSE 14. LOW BEAM RELAY 5. LH HI BEAM RELAY FUSE 10. STARTER RELAY 15. HIGH BYPASS RELAY 00-5
Lamps and Bulbs Application G.E. Bulb No. (Watts) Dome Lamp Bulb... Case Part No. 3050958R1, (10W) Console Lamp Bulb... No. 168 Flasher Lamp Bulb... No. 1156 Head Lamps... No. H4, (55W/60W Halogen) Brake Lamps... 3157 (37W) Side Work Lamps...No. 885, (50W) Front and Rear Flood Lamps, Optional Fender/Rear Roof/Beltline Flood Lamps... No. H3, (55W) Tail Lamp Bulbs... No. 3157, (37W) Fender Standard Work Lamp...No. 894, (37W) Front Roof Work Lamp...No. 894, (37W) Center Grille Work Lamp...No. 885, (50W) HID Center Roof Work Lamp...New Holland Part No. 86988628, (35W) Strobe Light...No. 400, (80W) Number Plate Lamp... Case Part No. P40556 Accessory Connectors 7 Terminal Electrical Outlet... Equipped for Directional Lamps, Tail lamps and 12 Volt Power for Implements with Fuse Protection 3 Pin Cab Connector (2 Standard) (2 Optional)...12 volt Power with/or with/out Key Switch and Direct Ground for Implement Controllers and Monitors! WARNING: Do not look directly into the High Intensity Discharge Lamp. Eye damage can occur. M638! WARNING: Do not tamper with the ballast on the High Intensity Discharge Lamp as it contains high voltage. Personal injury or death can occur. M639 00-6
Air Conditioner System Specifications Refrigerant Type...HFC-134A Per ARI Standard 700 System Capacity... 2100 grams 4.63 lb Compressor Manufacture...SANDEN Model...SD 7H15MD4609 Clutch Current Draw at 12 Volts...2 Amps Clearance Between Front Plate and Pulley... 0.4 to 0.8 mm 0.016 to 0.32 inch Engine Specifications Make... CDC Model... 6TAA - Magna Force Firing Order...1-5-3-6-2-4 Bore and Stroke... 114 mm x 135 mm Displacement... 8.3 liters Engine Speeds High Idle TG 210...2415 to 2505 RPM TG 230...2395 to 2485 RPM TG 255 and TG 285...2390 to 2410 RPM Rated Engine Speed All Engines...2200 RPM Low Idle All Engines...850 to 950 RPM Valve Clearance-Engine Cold Intake Valves... 0.25 mm Exhaust Valves... 0.50 mm 0.010 inch 0.020 inch Transmission Specifications Number of Forward Speeds... 18 - Full Power shift Reverse Speeds...4 Creeper Speeds (If Equipped)...6 Forward and 2 Reverse Hitch Specifications Type Hitch... Three Point, Category III (Convertible to II or IIIN) Lift Capacity at 24 Inch (610 mm) Behind Lift Point Standard Hitch TG 210 and 230... 6 134 Kg (13 520 lb) TG 255... 6 789 Kg (14 970 lb) TG 285... 7 301 Kg (15 970 lb) Optional Hitch TG 210 and 230... 7 301 Kg (15 970 lb) TG 255 and 285... 8 138 Kg (17 920 lb) European Hitch TG 210... 6 283 Kg (13 850 lb) TG 230 and 255... 6 706 Kg (14 780 lb) TG 285... 7 416 Kg (16 350 lb) Type Draft Arms TG 210 and 230...Telescoping TG 255 and 285...Rigid With Integral Quick Coupler Position Control and Draft Control... Electronic 00-7
SPECIAL TORQUES Alternator Mounting Bolts... 100 Nm Pulley Retaining Nuts... 60 to 70 Nm MFD Steering Cylinder and Axles King Pin Retaining Bolts... 156 to 170 Nm Socket Clamp to Steering Cylinder... 95 to 108 Nm Steering Cylinder Tapered Stud...10 Bolt - 190 / 12 Bolt - 272 Nm Tie Rod Tapered Stud... 275 Nm Differential Housing to Axle Bolts... 122 to 135 Nm Ring Gear Bolts... 163 to 190 Nm Wheel Carrier to Knuckle Bolts... 110 to 125 Nm Planetary Carrier to Wheel Hub Screws... 10 to 16 Nm Wheel Hub Drain / Filler Plug... 40 Nm Front Wheel Disc to Rim Nuts - MFD... 298 to 366 Nm Disc to Front Axle Hub Nut - MFD... 385 to 425 Nm MFD Drive Shaft Retaining Bolts... 67 to 73Nm MFD Output Shaft Bearing Cage M20 X 60-12.9... 375 to 485 Nm M20 X 150-12.9... 375 to 485 Nm Transmission Speed to Range Transmission Retaining Bolts M16 X 60-8.8... 234 to 260 Nm M16 X 80-10.9... 220 to 250 Nm M20 X 90-10.9... 430 to 486 Nm Range Transmission to Rear Frame M16 X 60-8.8... 232 to 262 Nm M16 X 80-10.9... 220 to 250 Nm M16 X 110-10.9... 220 to 250 Nm Wheel to Hub Bolts... 528 to 569 Nm Wheel Bushing Bolts... 300 to 350 Nm Axle Carrier to Rear Frame - All... 229 to 265 Nm (Thru Axle Carrier Flange Into Rear Frame) Differential and Differential Lock Ring Gear Retaining Bolts... 297 to 328 Nm Differential Lock Clutch Cage Retaining Bolts... 297 to 328 Nm Hydraulic PTO PTO Housing Retaining Bolts... 55 Nm PTO Speed Sensor... 16 to 22 Nm 74 lb ft 44 to 52 lb ft 115 to 125 lb ft 70 to 80 lb ft 10 Bolt 140 / 12 Bolt 200 lb ft 200 lb ft 90 to 100 lb ft 120 to 140 lb ft 89 to 90 lb ft 7 to 12 lb ft 30 lb ft 220 to 270 lb ft 285 to 315 lb ft 49 to 54 lb ft 277 to 358 lb ft 277 to 358 lb ft 173 to 192 lb ft 162 to 185 lb ft 317 to 358 lb ft 171 to 193 lb ft 162 to 184 lb ft 162 to 184 lb ft 390 to 420 lb ft 220 to 260 lb ft 169 to 195 lb ft 219 to 242 lb ft 219 to 242 lb ft 40 lb ft 12 to 16 lb ft 00-8
Hydraulics Hydraulic Pump Mounting Bolts... 134 to 151 Nm Charge / Lubrication Pump Mounting Bolts... 134 to 151 Nm Solenoid Valve Installation Torque... 19 to 25 Nm Solenoid Valve Coil Retaining Nut... 5 to 8 Nm Remote Valve Retaining Nuts... 61 to 69 Nm Load Check Valve Body... 34 to 41 Nm Load Check Poppet Spring Retainer... 4 to 5 Nm Check Valve Body... 16 to 19 Nm Check Valve Plug... 4 to 4.5 Nm PTO Spool End Plug... 19 to 25 Nm Inching Spool End Plug... 19 to 25Nm Pressure Transducer... 19 to 25 Nm Rear Hitch Top Link Mounting Bracket (M20)... 490 to 550 Nm RH and LH C Bracket Casting Bolts (M24)... 845 to 950 Nm Rocker Tie Bolt (M24)... 490 to 550 Nm Quick Coupler Latch Bolt (M16)... 95 to 125 Nm Air Conditioning Compressor Clutch Retaining Nut... 15 to 20 Nm Compressor Oil Fill Plug... 15 to 24 Nm Dust Cover Screws... 7 to 11 Nm Low / High Pressure Switch... 14 to 20 Nm 99 to 112 lb ft 99 to 112 lb ft 14 to 18.5 lb ft 4 to 6 lb ft 45 to 51 lb ft 25 to 30 lb ft 3 to 4 lb ft 12 to 14 lb ft 3 to 3.5 lb ft 14 to 18.5 lb ft 14 to 18.5 lb ft 14 to 18.5 lb ft 360 to 405 lb ft 625 to 700 lb ft 360 to 405 lb ft 70 to 90 lb ft 11 to 15 lb ft 11 to 18 lb ft 5 to 8 lb ft 10 to 15 lb ft 00-9
00-10