Delta IP65: New Light with a high protection factor The continuous-line luminaire Delta IP65 impresses with a particularly high protection rating for solid and liquid materials. It combines protection with efficiency: Its particular strengths are due to high-quality components such as the robust aluminium section state-of-the-art Miro Silver reflector technology allows for the best possible light efficiency. Flexible: The flexible modular system enables tailor-made solutions for any on-site requirement. Safe: High quality components achieve IP65 protection, meaning the continuous line is outstandingly suitable for damp rooms. Uncomplicated: Simple logic and intelligent concept make installation child s play. Efficient: The continuous line is especially efficient due to Miro Silver reflector technology. Long-life: Interplay of high quality components means a long operating and service life.
Due to its all-around closed design and the use of high-quality components, the continuous line luminaire implements the protection rating IP65. The Delta IP65 is therefore also ideally suited for use in wet rooms. The sophisticated reflectors made of Miro Silver material assure optimal light efficiency. The Plug&Play system allows for easy and quick installation. 1
Rapid mounting continuous line luminaire system with integral trunking Suspension Base unit End cap for base unit Gear tray for T5 Photometric accessories reflector Cover IP65 Same profile for different lamp options All gear trays of the Delta programme are installed into a standard base profile. For example, in the event there are zones requiring different strengths of illumination, this allows for the use of both single-lamp gear trays and twin-lamp models. As a result, the reticulated appearance typical of Delta remains unaffected, independent of the respective light needs. 2
Base units q54oa IP65 0.2 Joule PMMA 650 C Silicate glass 850 C 07620 Base units Integral trunking and reflector profile. Luminaire body made of anodised extruded aluminium profile. Tool-free installation of gear trays, for T5 lamps, in single-lamp and twin-lamp version. 07620 E/ Base unit for individual luminaires. With 5-pole female connector, direct light distribution. With silicate cover, clear, safely held in surrounding frame, for maintenance purposes hinged access and suspension at the reflector, protection rating IP65. 07620 Base unit for continuous line luminaires. With pre-assembled trunking connector on one side. Factory wired with heat-resistant single wires, 1.5 mm² or 2.5 mm², with 5-pole or 7-pole male/female pair for quick electrical connection of trunking, direct light distribution, with silicate cover, clear, safely held in surrounding frame, for maintenance purposes hinged access and suspension at the reflector, protection rating IP65. 7620 E/ PMMA Base unit for individual luminaires. With 5-pole female connector, direct light distribution. With PMMA cover, clear, safely held in surrounding frame, for maintenance purposes hinged access and suspension at the reflector, protection rating IP65. Description TOC Length kg mm Base units with silicate glass cover 07620 E/1500 07 60 618 00 1500 7.4 Wire diameter 1.5 mm² 07620 II/5LV-1.5/1500 07 60 619 00 3000 11.8 07620 III/5LV-1.5/1500 07 60 620 00 4500 16.0 07620 II/7LV-1.5/1500 07 60 621 00 3000 11.9 07620 III/7LV-1.5/1500 07 60 622 00 4500 16.2 Wire diameter 2.5 mm² 07620 II/5LV-2.5/1500 07 60 623 00 3000 12.0 07620 III/5LV-2.5/1500 07 60 624 00 4500 16.2 07620 II/7LV-2.5/1500 07 60 625 00 3000 12.1 07620 III/7LV-2.5/1500 07 60 626 00 4500 16.5 Base units with PMMA cover 07620 E/1500 PMMA 07 60 695 00 1500 6.3 Wire diameter 1.5 mm² 07620 II/5LV-1.5/1500 PMMA 07 60 696 00 3000 10.6 07620 III/5LV-1.5/1500 PMMA 07 60 697 00 4500 14.8 07620 II/7LV-1.5/1500 PMMA 07 60 698 00 3000 10.8 07620 III/7LV-1.5/1500 PMMA 07 60 699 00 4500 15.0 Wire diameter 2.5 mm² 07620 II/5LV-2.5/1500 PMMA 07 60 700 00 3000 10.8 07620 III/5LV-2.5/1500 PMMA 07 60 701 00 4500 15.1 07620 II/7LV-2.5/1500 PMMA 07 60 702 00 3000 11.0 07620 III/7LV-2.5/1500 PMMA 07 60 703 00 4500 15.3 Base units can be equipped with gear trays in single-lamp or in twin-lamp version. Gear trays must be ordered separately. 07620 PMMA Base unit for continuous line luminaires. With pre-assembled trunking connector on one side. Factory wired with heat-resistant single wires, 1.5 mm² or 2.5 mm², with 5-pole or 7-pole male/female pair for quick electrical connection of trunking, direct light distribution, with PMMA cover, clear, safely held in surrounding frame, for maintenance purposes hinged access and suspension at the reflector, protection rating IP65. 07620 1500 ( I ), 3000 ( II ), 4500 ( III ) 3
Gear trays q54oa IP65 0.2 Joule PMMA 650 C Silicate glass 850 C 7621/ 7621 A 7622 Areas of application Production facilities, workshops, assembly halls, sales areas, training rooms, welding work spaces and chemical factories. Gear trays for T5 fluorescent lamps Sheet steel, white. Mounts to base unit through tool-free metal rotary latch, plasticcoated. Electrical connection Occurs automatically upon placing the gear tray into the base unit. Lamp circuit connections can be adjusted tool-free to the relevant conductor. Description TOC Electrical version Light sources Length kg terminology E EDD W mm Single-lamp version 7621/35/49/80 60 633 04 07 1 x 35/49/80 2 1.7 Single-lamp version, asymmetrical* 7621 A/35/49/80 60 638 04 07 1 x 35/49/80 2 1.9 Twin-lamp version 7622/35/49 60 634 04 07 2 x 35/49 2 1.8 * For an asymmetric light distribution, an asymmetric specular reflector 07620SAX must be used. Electrical version Version 35/49 in multi-lamp technology for operation of T5 lamps of different power levels. E with electronic ballast. EDD With digitally dimmable electronic control gear (DALI). 7621 7621 A 7622 07620 SAX 4
Gear tray for emergency lighting q54oa IP65 0.2 Joule PMMA 650 C Silicate glass 850 C E EB E+UR Gear tray + EB1 Gear trays for continuous line luminaires and individual luminaires with electronic control gear (EVG) and individual battery. Sheet steel, white. Mounts to base unit through tool-free metal rotary latch, plastic-coated. With electronic control gear (EVG). Fluorescent lamps in continuous mode, in case of mains failure continued operation of one lamp on individual battery with maintenance-free batteries, light emitting diode as indicator of level of charge. + EB1 Nominal operation time 1 hour. + EB3 Nominal operation time 3 hours. Description TOC Length of Light sources Length kg operation terminology W mm Gear tray with individual battery supply for continuous mode 7621/35/49/80 E EB1H 60 635 04 1 hour 1 x 35/49/80 2 2.5 7621/35/49/80 E EB3H 60 636 04 3 hours 1 x 35/49/80 2 2.7 7622/35/49 E EB3H 60 637 04 3 hours 2 x 35/49 2 3.1 Gear tray with relay for continuous mode 7621/35/49/80 E+UR 60 708 04 1 x 35/49/80 2 1.8 7622/35/49 E+UR 60 709 04 2 x 35/49 2 2.1 Gear tray + UR Gear trays for continuous line luminaires and individual luminaires. With electronic control gear (EVG) and relay for switching to safety current supply. Electronic ballast in multilamp technology for operation of T5 lamps of different power levels. Fluorescent lamps in continuous mode, in case of mains failure continued operation of one lamp on site by standby power source. Sheet steel, white. Mounts to base unit through tool-free metal rotary latch, plastic-coated. With electronic control gear (EVG). Electrical connection The connection to the electrical and the emergency circuit takes place automatically upon placing the gear tray into the base unit. Lamp circuit connections can be adjusted tool-free. With electronic Multi-Lamp control gear. 5
Optical systems q54oa IP65 0.2 Joule PMMA 650 C Silicate glass 850 C 07620 HRLX 07620 STX 07620 SBX 07620 SAX 07620 RSX-Ag Specular reflector HRLX. Energy-efficient specular reflector for the highest degree of efficiency. With reflectionintensifying silver surface, highly specular. Reflectance value > 98 %. For extremely narrow-angle light distribution. Specular reflector STX. Energy-efficient specular reflector for the highest degree of efficiency. With reflectionintensifying silver surface, highly specular. Reflectance value > 98 %. For symmetrical narrow-angle light distribution. Description TOC Component designation kg Specular reflectors 07620 HRLX 60 628 00 Miro Silver specular reflector HRLX, extremely narrow-angle light distribution 0.3 07620 STX 60 629 00 Miro Silver specular reflector STX, narrow-angle light distribution 0.3 07620 SBX 60 631 00 Miro Silver specular reflector SBX, wide-angle light distribution 0.3 07620 SAX 60 630 00 Miro Silver specular reflector SAX, asymmetrical light distribution 0.3 Specular louvre 07620 RSX-Ag 60 632 00 Miro Silver specular louvre RSX, semi-specular 0.4 Blanking cover 07620 B/1500 60 707 00 Blanking cover 1500 mm long 1.1 Please order base units and gear trays separately. Specular reflector SBX. Energy-efficient specular reflector for the highest degree of efficiency. With reflectionintensifying silver surface, highly specular. Reflectance value > 98 %. For symmetrical wide-angle light distribution. Specular reflector SAX. Energy-efficient specular reflector for the highest degree of efficiency. With reflectionintensifying silver surface, highly specular. Reflectance value > 98 %. For asymmetrical light distribution. Parabolic louvre RSX-Ag. Energy-efficient parabolic louvre. With reflection-intensifying silver surface, semi-specular. Reflectance value > 98 %. VDU-compliant in accordance with EN 12464-1 due to reduced illuminance L 1000 cd/m² for distribution angles above 65 all around. Blanking cover B/1500. Sheet steel, white. Mounts to base unit through tool-free metal rotary latch, plasticcoated. 07620 HRLX 07620 STX 07620 SBX 07620 RSX-Ag 6
Accessories q54oa IP65 0.2 Joule PMMA 650 C Silicate glass 850 C 07620 M-RK PC A 01 SX VA S A 01 SX VA K A 01 SX VA D Description TOC kg End caps 07620 M-RK PC 60 627 00 0.2 Wire suspensions A 01 SX VA S 60 683 00 0.1 A 01 SX VA K 60 684 00 0.2 A 01 SX VA D 60 685 00 0.1 E 03 KD 23 427 00 0.1 E 01 VA 60 711 00 0.1 03630S 29 265 00 End caps 1 pair end caps, for base units 07620, plastic, silver-grey, with 2 knockouts. Each continuous line luminaire and/or individual luminaire requires 2 end caps. Wire suspension 1 piece, consisting of stainless steel wire, 2000 mm long, and suspension clamp, with loop and a spring hook. Height tool-free adjustable. Wire suspension 1 piece, consisting of stainless steel wire, 2000 mm long, and suspension clamp, with two spring hooks. Height toolfree adjustable. Wire suspension 1 piece, consisting of stainless steel wire, 2000 mm long, and suspension clamp, with M6 thread fixing and a spring hook. Height tool-free adjustable. E 03 KD E 01 VA 03630S Suspension clamp 1 piece, for chain suspension, stainless steel, for tool-free mounting on the base unit. Ceiling fixing plate 1 piece. Sheet steel, galvanised, with spring hook for tool-free hanging of chains and wires. Removal tool Vacuum plug for removing luminaire covers OA and OTA in case of maintenance. 7
Contacts TRILUX GmbH & Co. KG Heidestraße D-59759 Arnsberg Postfach 19 60 D-59753 Arnsberg Tel. +49 (0) 29 32.3 01-0 Fax +49 (0) 29 32.3 01-3 75 sales@trilux.com www.trilux.com PROLJUS AB Kyrkogatan 18 570 03 VRIGSTAD Tel. +46 (0) 70 601 05 63 info@proljus.se - www.proljus.se 8
11/44-GB-int. 085 043