Revised 6/01 Flexible Sewer couplings are the result of many years of experience with sewer pipe connections. Today's couplings are made of specially formulated elastomeric PVC with high tear and shear strength and are highly resistant to caustic chemicals. Saddles Sewer service saddles provide accurate, economical and fast installation of sewer lines. The newer stainless steel strap-on type saddle eliminates the need for bolting and drilling, while insuring watertight seal. Saddles are available in 45 and 90 angles and are made for all types of sewer lines. O.D. Chart NOTE: Due to variations in outside diameter and specifications, dimensions listed above are approximate. For this reason, the O.D. of the pipe being used must be determined before placing order.
K-1 Flexible For Sewer and Drain Connection and Repair Straight Coupling Connect pipes of same or different sizes and materials, quickly and easily Positive seal against infiltration and exfiltration Stainless steel clamps are corrosion-resistant and rustproof Leakproof, rootproof Reducing Coupling Fast: Takes only minutes for average connection. Simple: Place coupling over spigot and tighten bands. Economical: Saves money by saving on installation time. K coupling SIZE (inches) clay clay clay CI or PVC clay ac, fibre or DI concrete concrete concrete ci or pvc ac, fibre or di ci or pvc ac, fibre or di ac, fibre or di ci, pvc, copper or steel ci, pvc, copper or steel 4 3 * 62217 * * 62219 * * 62218 4 4 62236 62245 62235 62232 62237 62234 62233 62247 5 4 * 62279 62277 * * 62287 * * 5 5 * 62283 62281 * * 62282 62284 62282 1 6 4 * 62317 * * 62316 62315 * 62337 6 5 62306 62305 62307 * * 62344 62342 * 6 6 62323 62326 62313 62310 62325 62309 62308 62314 8 4 * * * * * * * 62447 8 6 62415 62418 62445 * 62417 62449 * 62448 8 8 62451 62458 62456 * 62454 62453 62452 62455 10 8 * 62466 * * 62464 62468 * 62465 10 10 62472 62477 62484 * 62476 62488 62486 62475 12 10 * 62499 * * * * * 62498 12 12 62512 62528 62514 62515 62517 62516 * 62524 15 12 * 62535 * * * * * * 15 15 62536 62537 62540 * 62534 62538 * 62539 18 18 62547 3 62547 62547 1 * 62547 2 62547 4 * 62546 24 24 * 62550 1 * * * * * 62550 * Non-Stock items; other sizes and material combinations are available upon request. conform to applicable parts of ASTM C443, C564 and D1869. www.ejprescott.com K-1
K-2 Caps and Manhole Adapters Flexible Cap Concrete Manhole Adapters Fast, easy installation Permanent or temporary cap For underground or above-ground use Low cost and reusable Caps offer a quick, easy way to cap pipe ends, cleanouts and open test pipes. Made of flexible PVC, they're suitable for either above ground or underground use on cast iron, steel, copper or plastic piping. Caps are designed to fit all drain, waste and vent pipe materials in a given nominal size. The convex face allows the cap to withstand greater pressure for testing purposes and minimizes ballooning. To install, simply place over open end of pipe and tighten to 60 inch lbs. torque. Concrete Manhole Adapters (CMA) help eliminate leaks around pipe entering manhole walls, yet are flexible enough to permit lateral pipe movement without destroying seal integrity. It is particularly useful for pipe to which concrete will not adhere, such as plastic pipe. The CMA is made of elastomeric PVC, is corrosion proof and is unaffected by acid or alkali. Because the CMA may be subjected to various conditions beyond the manufacturer s control which can affect its ability to seal, discretion must be used in its application and installation. Due to the various factors that can influence the CMA s effectiveness as a seal, (high water tables, quality of grout, workmanship and field conditions) Fernco does not warrant this product as a positive water seal. CAPS size PRODUCT NUMBER 4" 62195 6" 62197 8" 62199 PRODUCT size NUMBER CONCRETE 4" 62242 MANHOLE 6" 62385 8" 62459 ADAPTER 10" 62481 12" 62522 NOTE: Larger sizes available upon request. K-2 Phone: 800-EJP-24HR (357-2447) Fax: 207-582-5637
K-3 Flexible Sewer Saddles Flexible Sewer Saddles Features: The flexible sewer saddle's elastomeric construction will allow one saddle to fit pipe diameters of 4" through 12" thus eliminating the need for an inventory of various sizes of rigid PVC saddles. The flexible sewer saddle is available with a 4" or 6" inlet. The flexible sewer saddle is tightened onto the pipe with stainless steel series 300 clamps. Steel reinforced edges prevent distortion when torque is applied to the stainless steel bands. Inlet range from SCH-40 pipe down to SDR-35 pipe which includes standard weight soil pipe. Available in Tee or Wye configurations. DESCRIPTION 4" - 12" Flexible Tee Saddle 4" - 12" Flexible Wye Saddle inlet size PRODUCT NUMBER 4" 62891 6" 62893 4" 62892 6" 62894 Tee Saddle K Wye Saddle Installation Instructions: To insure a tight seal it is recommended that pressure be 1. applied to the skirt of the saddle as illustrated. 2. Then tighten clamps to at least 60 inch lbs. of torque. www.ejprescott.com K-3
K-4 PVC Inserta Tee Inserta Tee is a three-piece service connection that is compression fit into the cored wall of the mainline or manhole. Inserta Tee is easy to install and is used on all gravity flow pipe currently on the market. Inserta Tee consists of a PVC Hub, Stainless Steel Band and Rubber Sleeve, for side services of 4" (100mm) through 12" (300mm) and fits all mainline diameters. Features: New and Rehab Installations: Inserta Tee allows easier grading of mainline and ensures side services are installed exactly where they need to be. Tapping Existing Lines: Install Inserta Tee without disturbing the bedding while eliminating: 1. Glues, epoxies, grout and specialized gaskets. 2. Specialized tooling. 3. Tightening & retightening bands. Applications: Manholes Storm Sewers Irrigation Sanitary Sewers Drainage Inserta Tee Can Be Used With These Pipes: Ductile Iron Concrete Clay Polyethylene PVC Perma Loc Fiberglass N12 Culvert Spirolite Vylon H.C. HIQ/Sur-Loc Ultra Rib Culvert Installation Procedures: 1. Make sure bit is perpendicular to mainline. Core the proper size hole. Feel inside hole and clear any remaining material. 2. Insert the rubber sleeve into the cored hole with the gold vertical line on the rubber sleeve facing to the side of the mainline. The upper segment should be on top of the wall or rib and the lower segment (PVC, Ribbed & Polyethylene pipe only) should be on the inside of the pipe. Feel inside to be sure lower segment is flat against inside wall. 3. Apply the Inserta Tee solution supplied to the inside of the rubber sleeve and to the outside of the PVC hub adapter spigot. WARNING! Using pipe lube may result in Hub adapter popping out! 4. Place the PVC hub adapter into the rubber sleeve. Make sure that the red vertical line on the pvc hub adapter is in line with the gold vertical line on the rubber sleeve. Push hub adapter in as far as possible by hand. Make sure hub adapter is perpendicular to mainline. Forcing hub adapter through at an angle may cause damage to rubber sleeve or hub adapter. 5. Place a 2 x 4 board onto the top of the PVC hub adapter. 6. The red horizontal line at the top of the hub adapter is a depth mark. This tells the installer just how far to drive the adapter into the rubber sleeve. Drive the PVC hub adapter into the rubber sleeve to where the horizontal red line on the PVC hub adapter meets the top of the rubber sleeve. 7. Place the stainless band around the top of the rubber sleeve and tighten down. 8. Install sideservice pipe in normal manner. NOTE: Inserta Tee construction varies with pipe type and size. For pipe not listed please contact your local Team EJP Sales Office. K-4 Phone: 800-EJP-24HR (357-2447) Fax: 207-582-5637
K-5 QwikSeal Connectors QS-4 Connects 4" SDR-35 Plain End Pipe Stub to 8" and Larger Drain Pipe QS-6 Connects 6" SDR-35 Plain End Pipe Stub to 10" and Larger Drain Pipe QwikSeal allows you to connect service pipes to all known solid wall, profile, closed profile and corrugated pipe manufactured today. Features: Available in 4", 6" and 8" sizes Use a standard 5" or 7" hole cutter One size fits ALL clay, PVC, concrete and corrugated pipe materials No more searching for the right gasket Fast - Simple - Reliable Tap into new, existing and rehabilitated sanitary and storm sewer Heavy duty 316 series stainless steel clamp SDR 35 Pipe Connected to Concrete K SDR 35 Pipe Connected to Clay SDR 35 Pipe Connected to Corrugated Polyethylene Drain Pipe www.ejprescott.com K-5
K-6 Mechanical Plugs Gripper Plugs Cherne s Gripper plugs can be used in a variety of applications including DWV (drain, waste and vent) testing and stack testing. End-of-the-pipe design won t fall in, whereas the Inside-of-the-pipe design allows you to locate the plug inside the pipe as far as you need. Features: Ideal for sewer testing* and long-term applications Made with glass-reinforced ABS plastic End-of-pipe design seals only at the end of a pipe Inside-of-pipe design seals inside pipe as far as needed Equipped with: 1. Easy-to-install extra-large wing nut 2. Natural rubber o-ring * Always block plugs when conducting air tests END TYPE PLASTIC GRIPPER PLUG nominal SIZE (inches) MINIMUM SEALING DIAMETER End of Pipe Gripper Plug MAXIMUM ALLOWABLE BACK PRESSURE AIR WATER PSIG FEET PRODUCT NUMBER 4" 3.80 5 40 27108 6" 5.76 5 40 27188 8" 7.76 5 40 27279 Inside Gripper Plugs Mechanical Bypass Plug INSIDE PLASTIC GRIPPER PLUG nominal SIZE (inches) MINIMUM SEALING DIAMETER MAXIMUM ALLOWABLE BACK PRESSURE AIR WATER PSIG FEET PRODUCT NUMBER 4" ¼" 3.80 5 40 27108 2 6" ½" 5.76 5 40 27189 1 8" ½" 7.76 5 40 27279 5 MECHANICAL BYPASS PLUG 8" ¾" 7.81 5 40 27278 10" ¾" 9.81 5 40 27356 12" 1¼" 11.68 5 40 27429 K-6 Phone: 800-EJP-24HR (357-2447) Fax: 207-582-5637
K-7 Pipe Plugs 6" to 60" The Pipe Plug The Pipe Plug can be used in Gas, Sewer, Water and Storm Drainage Applications. It will fit all pipe from 6" to 60", including, but not limited to the following: RCP Polyethylene Clay PVC Ductile Iron Steel Benefits: Stop sand and mud build-up Keep valves clean Keep children and animals out of pipes Decrease downtime - less cleaning of pipe needed Other Uses For The Plug: Temporary manhole covers Septic tank covers Weirs Caution: These pipe plugs are not to be used as test plugs K TEMPORARY PIPE PLUGS size USE ON PRODuct Number 6" SDR 35 27184 8" SDR 35 27279 2 8" DI/C900 27279 3 12" DI/C900 27429 1 NOTE: Custom size plugs are available upon request www.ejprescott.com K-7
K-8 Ko r-n-se a l I Connectors Ko r-n-se a l I - We d g e Ko r b a n d Flexible Pipe-To-Manhole Connector The Ko r-n-seal I Connector is ideally suited for small diameter pipe-to-manhole connections. It provides a flexible, watertight, environmentally safe joint that exceeds ASTM C923 specifications. A specially formulated EPDM rubber compound offers superior resistance to weather, ozone, oils, acids, alkalis and animal/vegetable fats. Both the Korband and the pipe clamp are nonmagnetic series 304 stainless steel to achieve maximum corrosion resistance. Installation: Ko r-n-seal I installation is simple and can be completed in minutes. It is a one man operation and a standard torque wrench installs any size Wedge-style connector. Detailed recommended installation procedures are included with every shipment. Advantages: Ensures a positive, watertight seal Can be installed in either cored or formed holes with wide diameter variations Accommodates both angular and lateral misalignment Provides a flexible, vibration-absorbing joint Allows for variations in pipe diameter tolerances Allows for changes in pipe material Can be easily replaced if necessary Ensures trouble-free, efficient installations Conforms to ASTM C923 specifications Accommodates ground movement and prevents shear Kor-N-Seal I Connectors SIZE PRODuct Number 7" 4" 62815 12" 6" 62818 12" 8" 62819 12" 10" 62820 16" 12" 62825 K-8 Phone: 800-EJP-24HR (357-2447) Fax: 207-582-5637