High-Pressure Fluid Swivel onnectors escription The figures in this document are for general reference only. High-pressure fluid swivel connectors can be used in a variety of different combinations, and with other high-pressure fittings or adapters. They are not pressure-balanced and therefore move more freely when the system is open and the application device is in use. epending on your requirements for coupling size and fitting type, you may purchase these modular swivels separately and assemble them according to your application needs. The types of connectors, sizes, and part numbers are listed in this document. Specifications Maximum fluid temperature: 450 F ( ) Maximum pressure: 4000 psi (76 bar) WRNING llow only qualified personnel to perform the following tasks. Follow the safety instructions in this document and all other related documentation. Select the Proper Swivel ombination Table shows the standard measurements for JI tube fittings. Use this information to select swivel connectors from the tables in this document. ash Numbers (JI-) Table JI Tube Fittings Tube O (in.) Straight Thread 5 5 / 6 / -0 6 / 8 9 / 6-8 8 / / 4-6 0 5 / 8 7 / 8-4 / 4 / 6-0 / 4 5 / 8-005 Nordson orporation Issued /05 Instruction Sheet: 0869
High-Pressure Fluid Swivel onnectors Small Swivels. See Figure and refer to Table. hoose one elbow swivel () as the basis for your assembly.. dd one straight swivel () to the elbow to create a two-plane assembly or add an elbow swivel () and a straight swivel () to create a three-plane assembly. (male) (female) (male) F E Figure Small Swivels Typical ombinations Table Small Swivel onnectors ÁÁÁÁ Á Swivel End Swivel End Note Item Part ÁÁÁÁ Á ÁÁÁÁ Á 905 ÁÁÁÁ / 4 in. NPT (male) Á 9 ÁÁÁÁ / 8 in. NPT (male) Á SE-6 (female) 9098 ÁÁÁÁ / 8 in. NPSM (female) Á 909 ÁÁÁÁ SE-6 (male) Á ÁÁÁÁ Á ÁÁÁÁ 909 JI-5 (male) ÁÁÁÁ 909 JI-6 (male) 9094 JI-8 (male) ÁÁÁÁ SE-6 (male) Á 9095 ÁÁÁÁ ÁÁÁÁ JI-0 (male) ÁÁÁ 9096 ÁÁÁ JI- (male) ÁÁÁ 9097 ÁÁÁ JI-0 (male) ÁÁÁ ÁÁÁÁ E ÁÁÁÁ F ÁÁÁ ÁÁÁÁ 909 SE-6 (male) SE-6 (female) : Use this swivel with the standard Pro-Flo trim set outlet or other compatible adapter. : These straight swivels can also be used alone as single swivels. Instruction Sheet: 0869 Issued /05 005 Nordson orporation
High-Pressure Fluid Swivel onnectors Miscellaneous Straight Swivels See Figure and refer to Table, which lists miscellaneous straight swivel connectors. These straight swivels cannot be combined with any other swivels. Figure Small Swivels Typical ombinations Table Miscellaneous Straight Swivels Item Part ÁÁÁÁ Swivel End ÁÁÁÁ Swivel End ÁÁÁ Note 906 ÁÁÁ JI-5 (male) ÁÁÁ 907 ÁÁÁ JI-6 (male) ÁÁÁ ÁÁÁÁ 908 JI-8 (male) ÁÁÁÁ / 4 in. NPT (male) Á 909 JI-0 (male) ÁÁÁÁ 90 ÁÁÁÁ ÁÁÁÁ ÁÁÁ JI- (male) Á 9 ÁÁÁ JI-0 (male) ÁÁÁ 9 ÁÁÁ JI-5 (male) ÁÁÁ 94 ÁÁÁ JI-6 (male) ÁÁÁ 95 ÁÁÁÁ ÁÁÁÁ JI-8 (male) ÁÁÁ ÁÁÁÁ / 8 in. NPT (male) Á 96 JI-0 (male) ÁÁÁÁ 97 JI- (male) ÁÁÁÁ 98 JI-0 (male) ÁÁÁÁ 9099 ÁÁÁÁ ÁÁÁÁ ÁÁÁ JI-5 (male) Á 900 ÁÁÁ JI-6 (male) ÁÁÁ 90 ÁÁÁÁ ÁÁÁÁ JI-8 (male) ÁÁÁ 90 ÁÁÁÁ / 8 in. NPSM (female) ÁÁÁÁ JI-0 (male) ÁÁÁ 90 ÁÁÁ JI- (male) ÁÁÁ ÁÁÁÁ 904 JI-0 (male) : Use item (Figure ) for reference. This swivel looks identical to item but varies in size. 005 Nordson orporation Issued /05 Instruction Sheet: 0869
4 High-Pressure Fluid Swivel onnectors Large Swivels. See Figure and refer to Table 4. hoose one elbow swivel () as the basis for your assembly.. dd one straight swivel () to the elbow to create a two-plane assembly or add an elbow swivel () and a straight swivel () to create a three-plane assembly. E F Figure Large Swivels Typical ombinations Table 4 Large Swivels ÁÁ Swivel End ÁÁÁÁ Note Á 5795 SE-0 (male) SE- (female) 5794 SE- (male) SE- (female) ÁÁÁÁ ÁÁÁ ÁÁÁÁ 5796 ÁÁÁÁ SE- (male) ÁÁÁ JI-0 (male) ÁÁÁÁ 5799 ÁÁÁÁ SE- (male) ÁÁÁ JI-0 (male) ÁÁÁÁ 5800 ÁÁÁÁ SE- (male) ÁÁÁ JI-6 (male) ÁÁÁÁ 55469 ÁÁÁÁ SE- (male) ÁÁÁ JI-4 (male) ÁÁÁÁ 75589 SE-0 (male) JI-0 (male), 6496 SE-0 (male) JI-6 (male), E F 5794 ÁÁÁÁ SE- (male) ÁÁÁ SE- (female) ÁÁÁÁ Swivel End Item Part ÁÁÁÁ : These straight swivels can be used as single swivels. : This large straight swivel can only be used as a single swivel and cannot be used to configure two- and three-plane assemblies. Use item (Figure ) for reference only this swivel cannot be joined with an elbow. Instruction Sheet: 0869 Issued /05 005 Nordson orporation
High-Pressure Fluid Swivel onnectors 5 ssemble the Swivels To prepare and assemble the two- and three-plane swivel assemblies, perform the following procedures based on swivel size. Small Swivels WRNING Once assembled, these swivels must not be disassembled. Failure to follow this could result in leakage, swivel damage, and the chance of personal injury or component damage. The callouts in this procedure refer to the ordering information listed in Table 5. Use the following procedures to assemble small swivels.. Verify the swivel configuration and that the connectors are compatible before assembling them. Use the proper size O-rings () for the SE-6 connectors.. pply cleaner or primer () to the threads of the parts to be fitted.. pply threadlocking adhesive () to the threads of the parts to be fitted. 4. Install the parts by hand and tighten until the O-ring begins to be compressed. 5. Tighten the swivel connectors lightly with a wrench. 6. llow the thread sealant to dry for 90 minutes before using the swivel assembly. Table 5 ssembly Items Item Part escription 94508 O-ring, Viton, black, / 8 tube (SE-6) 94505 O-ring, Viton, 5 / 8 tube (SE-0) 94509 O-ring, Viton, / 4 tube (SE-) 900455 Primer, thread adhesive 900470 dhesive, threadlocking Large Swivels WRNING You must use a swivel lock key to install large swivel SE connectors. Otherwise, the connection could loosen and leak, a cause a threat to personnel in the area. Use the following procedures to assemble large swivels. You may disassemble the large swivel assemblies if you re-install the swivel lock key as detailed in these procedures.. Make sure that your swivel configuration is correct and that the connectors are compatible before assembling them. Use the proper size O-ring for the SE-0 and SE- connectors. Refer to Table 5 for O-ring ordering information.. See Figure 4. Remove the cap screw and swivel lock key () from the elbow swivel.. ssemble the parts by hand and tighten the SE connection until the O-ring compresses slightly. 4. Tighten the SE connection with a wrench. o not overtighten. Locate the two tapped holes (4) on the elbow swivel near the SE connection. Use only one hole to secure the swivel lock key () to the elbow swivel. 5. Position the swivel lock key so the cutout () rests against the SE hex (5). 6. Move the swivel lock key () so the slot () aligns with one of the two tapped holes (4) in the elbow swivel. Install and tighten the cap screw in this hole. 7. Repeat steps 6, as needed, when assembling three-plane swivels to attach each additional swivel lock key. Figure 4 5 4 Swivel Lock Key 005 Nordson orporation Issued /05 Instruction Sheet: 0869
6 High-Pressure Fluid Swivel onnectors Original copyright date 99. Nordson and the Nordson logo are registered trademarks of Nordson orporation. Viton is a registered trademark of E.I. upont de Nemours & o. Instruction Sheet: 0869 Issued /05 005 Nordson orporation